Skip to contentSkip to conversation

ARM: dts: exynos: Adjust ldo23 and ldo27 to lower levels on Arndale Octa

PATCH New Krzysztof Kozlowski 1 participant 3 messages Mar 9, 2019

Subsystems (2)
lore
Share & tools
lore

Krzysztof Kozlowski

author maintainer
#0 lore raw

PATCH 1/3 ARM: dts: exynos: Adjust ldo23 and ldo27 to lower levels on Arndale Octa

Although on the schematics of Insignal Arndale Octa board the PVDD_MIFS_1V1 (ldo23) and PVDD_G3DS_1V0 (ldo27) are marked as 1.2 V, the vendor v3.4 Android kernel sets them lower. Also name suggests that they should work on 1.1 V and 1.0 V respectively, not 1.2 V.

---
 arch/arm/boot/dts/exynos5420-arndale-octa.dts | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
arch/arm/boot/dts/exynos5420-arndale-octa.dts +4 -4
index 6f5e6e2fde22..751e772b5710 100644
@@ -504,8 +504,8 @@
 
 			ldo23_reg: LDO23 {
 				regulator-name = "PVDD_MIFS_1V1";
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <1200000>;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
 				regulator-always-on;
 			};
 
@@ -530,8 +530,8 @@
 
 			ldo27_reg: LDO27 {
 				regulator-name = "PVDD_G3DS_1V0";
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <1200000>;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
 			};
 
 			ldo28_reg: LDO28 {
Signature · 1 line
2.17.1
author maintainer
#1 lore raw

PATCH 2/3 ARM: dts: exynos: Add support for UHS-I SD cards on Arndale Octa

The Exynos5420's Mobile Storage Host supports SD cards in UHS-I standard (SD specification v3.0), with 1.8 V signaling in SD UHS DDR50. Adjust the regulator and add necessary capability properties. Change the SDR and DDR timings to match values in Insignal v3.4 Android kernel.

Tested with SD UHS-I card in SD UHS DDR50 mode.

---
 arch/arm/boot/dts/exynos5420-arndale-octa.dts | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)
arch/arm/boot/dts/exynos5420-arndale-octa.dts +6 -3
index 751e772b5710..96a0eb73a99b 100644
@@ -441,7 +441,7 @@
 
 			ldo13_reg: LDO13 {
 				regulator-name = "PVDD_APIO_MMCOFF_2V8";
-				regulator-min-microvolt = <2800000>;
+				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <2800000>;
 			};
 
@@ -701,14 +701,17 @@
 	status = "okay";
 	card-detect-delay = <200>;
 	samsung,dw-mshc-ciu-div = <3>;
-	samsung,dw-mshc-sdr-timing = <2 3>;
-	samsung,dw-mshc-ddr-timing = <1 2>;
+	samsung,dw-mshc-sdr-timing = <0 4>;
+	samsung,dw-mshc-ddr-timing = <0 2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
 	vmmc-supply = <&ldo19_reg>;
 	vqmmc-supply = <&ldo13_reg>;
 	bus-width = <4>;
 	cap-sd-highspeed;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	sd-uhs-ddr50;
 };
 
 &pinctrl_0 {
Signature · 1 line
2.17.1
author maintainer
#2 lore raw

PATCH 3/3 ARM: dts: exynos: Extend the eMMC node on Arndale Octa

In reply to Krzysztof Kozlowski

Describe properly the MMC0 node (with attached embedded MMC memory) on Arndale Node by:
1. Adding the regulator for host interface (although it still has to be "always-on" so the board with Linaro U-Boot will boot;
2. Using "non-removable" instead of "broken-cd" property, because eMMC is embedded into the board;
3. Adding support for HS200 v1.8 to indicate support in host controller although this has no practical effect (embedded memory does not support it).

---
 arch/arm/boot/dts/exynos5420-arndale-octa.dts | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)
arch/arm/boot/dts/exynos5420-arndale-octa.dts +9 -1
index 96a0eb73a99b..56a42c68bc39 100644
@@ -378,6 +378,12 @@
 				regulator-name = "PVDD_APIO_MMCON_1V8";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
+				/*
+				 * Must be always on, even though there is
+				 * a consumer (mmc_0).  Otherwise the board
+				 * does not reboot with vendor U-Boot
+				 * (Linaro for Arndale Octa, v2012.07).
+				 */
 				regulator-always-on;
 			};
 
@@ -685,7 +691,7 @@
 
 &mmc_0 {
 	status = "okay";
-	broken-cd;
+	non-removable;
 	card-detect-delay = <200>;
 	samsung,dw-mshc-ciu-div = <3>;
 	samsung,dw-mshc-sdr-timing = <0 4>;
@@ -693,8 +699,10 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
 	vmmc-supply = <&ldo10_reg>;
+	vqmmc-supply = <&ldo3_reg>;
 	bus-width = <8>;
 	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
 };
 
 &mmc_2 {
Signature · 1 line
2.17.1