MTD: Add Initial Hyperbus support
Vignesh Raghavendra
maintainerv2 cover MTD: Add Initial Hyperbus support
Cypress HyperBus is Low Signal Count, High Performance Double Data Rate Bus interface between a host system master and one or more slave interfaces. HyperBus is used to connect microprocessor, microcontroller, or ASIC devices with random access NOR flash memory(called HyperFlash) or self refresh DRAM(called HyperRAM).
Its a 8-bit data bus (DQ[7:0]) with Read-Write Data Strobe (RWDS) signal and either Single-ended clock(3.0V parts) or Differential clock (1.8V parts). It uses ChipSelect lines to select b/w multiple slaves. At bus level, it follows a separate protocol described in HyperBus specification[1].
HyperFlash follows CFI AMD/Fujitsu Extended Command Set (0x0002) similar to that of existing parallel NORs. Since Hyperbus is x8 DDR bus, its equivalent to x16 parallel NOR flash wrt bits per clk. But Hyperbus operates at >166MHz frequencies.
HyperRAM provides direct random read/write access to flash memory array.
Framework is modelled along the lines of spi-nor framework. HyperBus memory controller(HBMC) drivers call hyperbus_register_device() to register a single HyperFlash device. HyperFlash core parses MMIO access information from DT, sets up the map_info struct, probes CFI flash and registers it with MTD framework.
This is an early RFC, to know if its okay to use maps framework and existing CFI compliant flash support code to support Hyperflash
Also would like input on different types of HBMC master IPs out there and their programming sequences.
Would appreciate any testing/review.
Tested on modified TI AM654 EVM with Cypress Hyperflash S26KS512 by creating a UBIFS partition and writing and reading files to it. Stress tested by writing/reading 16MB flash repeatedly at different offsets using dd commmand.
HyperBus specification can be found at[1]
HyperFlash datasheet can be found at[2]
TI's HBMC controller details at[3]
[1] https://www.cypress.com/file/213356/download
[2] https://www.cypress.com/file/213346/download
[3] http://www.ti.com/lit/ug/spruid7b/spruid7b.pdf
Table 12-5741. HyperFlash Access Sequence
Enumeration log:
https://pastebin.ubuntu.com/p/GhqxJ8XTTx/
Change log:
Since RFC v1:
* Re-work Hyperbus core to provide separate struct representation for controller and slave devices
* Rename all files and func names to have hyperbus_ prefix
* Provide default calibration routine for use by controller drivers
* Fix up errors with patch spliting
* Address comments by Sergei Shtylyov <[email protected]>
Vignesh Raghavendra (5):
mtd: cfi_cmdset_0002: Add support for polling status register
dt-bindings: mtd: Add binding documentation for Hyperbus memory
devices
mtd: Add support for Hyperbus memory devices
dt-bindings: mtd: Add bindings for TI's AM654 Hyperbus memory
controller
mtd: hyperbus: Add driver for TI's Hyperbus memory controller
.../bindings/mtd/cypress,hyperbus.txt | 6 + .../devicetree/bindings/mtd/ti,am654-hbmc.txt | 27 +++ MAINTAINERS | 8 + drivers/mtd/Kconfig | 2 + drivers/mtd/Makefile | 1 + drivers/mtd/chips/cfi_cmdset_0002.c | 50 +++++ drivers/mtd/hyperbus/Kconfig | 21 ++ drivers/mtd/hyperbus/Makefile | 4 + drivers/mtd/hyperbus/hbmc_am654.c | 108 +++++++++++ drivers/mtd/hyperbus/hyperbus-core.c | 183 ++++++++++++++++++ include/linux/mtd/cfi.h | 5 + include/linux/mtd/hyperbus.h | 91 +++++++++ 12 files changed, 506 insertions(+) create mode 100644 Documentation/devicetree/bindings/mtd/cypress,hyperbus.txt create mode 100644 Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt create mode 100644 drivers/mtd/hyperbus/Kconfig create mode 100644 drivers/mtd/hyperbus/Makefile create mode 100644 drivers/mtd/hyperbus/hbmc_am654.c create mode 100644 drivers/mtd/hyperbus/hyperbus-core.c create mode 100644 include/linux/mtd/hyperbus.h
Signature · 6 lines
2.21.0 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Vignesh Raghavendra
maintainerRFC PATCH v2 1/5 mtd: cfi_cmdset_0002: Add support for polling status register
HyperFlash devices are compliant with CFI AMD/Fujitsu Extended Command Set(0x0002) for flash operations, therefore drivers/mtd/chips/cfi_cmdset_0002.c can be use as is. But these devices do not support DQ polling method of determining chip ready/good status. These flashes provide Status Register whose bits can be polled to know status of flash operation.
Cypress HyperFlash datasheet here[1], talks about CFI Amd/Fujitsu Extended Query version 1.5. Bit 0 of "Software Features supported" field of CFI Primary Vendor-Specific Extended Query table indicates presence/absence of status register and Bit 1 indicates whether or not DQ polling is supported. Using these bits, its possible to determine whether flash supports DQ polling or need to use Status Register.
Add support for polling status register to know device ready/status of erase/write operations when DQ polling is not supported.
[1] https://www.cypress.com/file/213346/download
--- drivers/mtd/chips/cfi_cmdset_0002.c | 50 +++++++++++++++++++++++++++++ include/linux/mtd/cfi.h | 5 +++ 2 files changed, 55 insertions(+)
drivers/mtd/chips/cfi_cmdset_0002.c +50 -0
@@ -49,6 +49,14 @@#define SST49LF008A 0x005a#define AT49BV6416 0x00d6 +/* +* Bits of Status Register definition for flash devices that don't +* support DQ polling (Eg.: Hyperflash) +*/ +#define CFI_SR_DRB BIT(7) +#define CFI_SR_ESB BIT(5) +#define CFI_SR_PSB BIT(4) +static int cfi_amdstd_read (struct mtd_info *,loff_t ,size_t ,size_t *,u_char *);static int cfi_amdstd_write_words (struct mtd_info *,loff_t ,size_t ,size_t *,const u_char *);static int cfi_amdstd_write_buffers (struct mtd_info *,loff_t ,size_t ,size_t *,const u_char *);
@@ -97,6 +105,18 @@ static struct mtd_chip_driver cfi_amdstd_chipdrv = { .module = THIS_MODULE }; +/* +* Use status register to poll for Erase/write completion when DQ is not +* supported. This is indicated by Bit[1:0] of SoftwareFeatures field in +* CFI Primary Vendor-Specific Extended Query table 1.5 +*/ +static int cfi_use_status_reg (struct cfi_private *cfi) +{ +struct cfi_pri_amdstd *extp = cfi->cmdset_priv; + +return (extp->MinorVersion >='5' ) && + (extp->SoftwareFeatures &0x11 ) ==1 ; +}/* #define DEBUG_CFI_FEATURES */
@@ -744,8 +764,21 @@ static struct mtd_info *cfi_amdstd_setup(struct mtd_info *mtd)*/ static int __xipram chip_ready(struct map_info *map, unsigned long addr) { +struct cfi_private *cfi = map->fldrv_priv;map_word d, t; +if (cfi_use_status_reg (cfi)) { +/* +* For chips that support status register, check device +* ready bit +*/ +cfi_send_gen_cmd (0x70 , cfi->addr_unlock1,0 , map, cfi, + cfi->device_type,NULL ); + d =map_read (map, addr); + +return d.x[0 ] &CFI_SR_DRB ; + } + d =map_read (map, addr); t =map_read (map, addr);
@@ -769,8 +802,25 @@ static int __xipram chip_ready(struct map_info *map, unsigned long addr)*/ static int __xipram chip_good(struct map_info *map, unsigned long addr, map_word expected) { +struct cfi_private *cfi = map->fldrv_priv;map_word oldd, curd; +if (cfi_use_status_reg (cfi)) { +/* +* For chips that support status register, check device +* ready bit and Erase/Program status bit to know if +* operation succeeded. +*/ +cfi_send_gen_cmd (0x70 , cfi->addr_unlock1,0 , map, cfi, + cfi->device_type,NULL ); + curd =map_read (map, addr); + +if (curd.x[0 ] &CFI_SR_DRB ) +return !(curd.x[0 ] & (CFI_SR_PSB |CFI_SR_ESB )); + +return 0 ; + } + oldd =map_read (map, addr); curd =map_read (map, addr);
include/linux/mtd/cfi.h +5 -0
@@ -233,6 +233,11 @@ struct cfi_pri_amdstd {uint8_t VppMin;uint8_t VppMax;uint8_t TopBottom; +/* Below field are added from version 1.5 */ +uint8_t ProgramSuspend; +uint8_t UnlockBypass; +uint8_t SecureSiliconSector; +uint8_t SoftwareFeatures; } __packed;/* Vendor-Specific PRI for Atmel chips (command set 0x0002) */
Signature · 1 line
2.21.0
Re: [RFC PATCH v2 1/5] mtd: cfi_cmdset_0002: Add support for polling status register
Quoted 14 lines · Vignesh Raghavendra
HyperFlash devices are compliant with CFI AMD/Fujitsu Extended Command Set(0x0002) for flash operations, therefore
drivers/mtd/chips/cfi_cmdset_0002.ccan be use as is. But these devices do not support DQ polling method of determining chip ready/good status. These flashes provide Status Register whose bits can be polled to know status of flash operation.Cypress HyperFlash datasheet here[1], talks about CFI Amd/Fujitsu Extended Query version 1.5. Bit 0 of "Software Features supported" field of CFI Primary Vendor-Specific Extended Query table indicates presence/absence of status register and Bit 1 indicates whether or not DQ polling is supported. Using these bits, its possible to determine whether flash supports DQ polling or need to use Status Register.
Quoted 2 lines
Add support for polling status register to know device ready/status of erase/write operations when DQ polling is not supported.
Isn't this new Status scheme just a copy of Intels(cmdset_0001)? If so I think the new status impl. in 0002 should borrow from 0001 as this is a hardened and battle tested impl.
I know other modern 0002 chips supports both old and new impl. of Status and I world guess that we will see more chips with new Status only.
Jocke
Vignesh Raghavendra
maintainerRe: [RFC PATCH v2 1/5] mtd: cfi_cmdset_0002: Add support for polling status register
Hi,
Quoted 15 lines · Joakim Tjernlund
Quoted 14 lines · Vignesh Raghavendra
HyperFlash devices are compliant with CFI AMD/Fujitsu Extended Command Set(0x0002) for flash operations, therefore
drivers/mtd/chips/cfi_cmdset_0002.ccan be use as is. But these devices do not support DQ polling method of determining chip ready/good status. These flashes provide Status Register whose bits can be polled to know status of flash operation.Cypress HyperFlash datasheet here[1], talks about CFI Amd/Fujitsu Extended Query version 1.5. Bit 0 of "Software Features supported" field of CFI Primary Vendor-Specific Extended Query table indicates presence/absence of status register and Bit 1 indicates whether or not DQ polling is supported. Using these bits, its possible to determine whether flash supports DQ polling or need to use Status Register.
Quoted 4 lines
Quoted 2 lines
Add support for polling status register to know device ready/status of erase/write operations when DQ polling is not supported.
Isn't this new Status scheme just a copy of
Intels(cmdset_0001)?
Yes, but with one difference: At the end of program/erase operation, device directly enters status register mode and starts reflecting status register content at any address.
The device remains in the read status register state until another command is written to the device. Therefore there is notion of device is in "status register read mode" (FL_STATUS) state
But in case of cfi_cmdset_0002, once program/erase operation is complete, device returns to previous address space overlay from which operation was started from (mostly read mode)
In order to enter status register overlay mode, Read Status command is to be written to addr_unlock1(0x555) address. The overlay is in effect for one read access, specifically the next read access that follows the Status Register Read command
Therefore code around FL_STATUS state in cfi_cmdset_0001 is not applicable to cfi_cmdset_0002 as is.
Quoted 3 lines
If so I think the new status impl. in 0002 should borrow from 0001 as this is a hardened and battle tested impl.
In case of cfi_cmdset_0001.c, program/erase is followed by inval_cache_and_wait_for_operation() to poll ready bit and based on status register value, success or the error handling is done.
Most of the code corresponding to inval_cache_and_wait_for_operation() is already in cfi_cmdset_0002.c. So, whats missing in this patch is handling and reporting of errors as reflected in status register after write/erase failures. I will add that in the next version.
But, I don't see much to borrow apart from error handling sequence. Please, let me know if I missed something.
Quoted 3 lines
I know other modern 0002 chips supports both old and new impl. of Status and I world guess that we will see more chips with new Status only.
Agreed. Newer devices would mostly be CFI 1.5.
Signature · 6 lines
Regards Vignesh ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [RFC PATCH v2 1/5] mtd: cfi_cmdset_0002: Add support for polling status register
Quoted 23 lines · Vignesh Raghavendra
CAUTION: This email originated from outside of the organization. Do not click links or open attachments unless you recognize the sender and know the content is safe.
Hi,
Quoted 17 lines · Joakim Tjernlund
Quoted 15 lines · Vignesh Raghavendra
HyperFlash devices are compliant with CFI AMD/Fujitsu Extended Command Set(0x0002) for flash operations, therefore
drivers/mtd/chips/cfi_cmdset_0002.ccan be use as is. But these devices do not support DQ polling method of determining chip ready/good status. These flashes provide Status Register whose bits can be polled to know status of flash operation.Cypress HyperFlash datasheet here[1], talks about CFI Amd/Fujitsu Extended Query version 1.5. Bit 0 of "Software Features supported" field of CFI Primary Vendor-Specific Extended Query table indicates presence/absence of status register and Bit 1 indicates whether or not DQ polling is supported. Using these bits, its possible to determine whether flash supports DQ polling or need to use Status Register.
Add support for polling status register to know device ready/status of erase/write operations when DQ polling is not supported.
Quoted 8 lines
Quoted 1 line
Isn't this new Status scheme just a copy of
Intels(cmdset_0001)?Yes, but with one difference: At the end of program/erase operation, device directly enters status register mode and starts reflecting status register content at any address.
The device remains in the read status register state until another command is written to the device. Therefore there is notion of device is in "status register read mode" (FL_STATUS) state
That seems to vary and long time ago RMK added this:
/* If the flash has finished erasing, then 'erase suspend' * appears to make some (28F320) flash devices switch to * 'read' mode. Make sure that we switch to 'read status' * mode so we get the right data. --rmk */ map_write(map, CMD(0x70), chip->in_progress_block_addr);
Quoted 4 lines
But in case of
cfi_cmdset_0002, once program/erase operation is complete, device returns to previous address space overlay from which operation was started from (mostly read mode)
I hope you can do the same as Intel here, issue an explicit Status CMD or you will be in trouble.
Also, I think you need to use the various map_word_xxx as in:
status = map_read(map, chip->in_progress_block_addr); if (map_word_andequal(map, status, status_OK, status_OK))
break;
otherwise you will break interleaved setups(like two 8-bit flashes in parallel to form one 16 bit bus). Maybe this is not supported for CMDSET 0002 ?
Jocke
Quoted 34 lines
In order to enter status register overlay mode, Read Status command is to be written to
addr_unlock1(0x555)address. The overlay is in effect for one read access, specifically the next read access that follows the Status Register Read command
Therefore code aroundFL_STATUSstate incfi_cmdset_0001is not applicable tocfi_cmdset_0002as is.Quoted 3 lines
If so I think the new status impl. in 0002 should borrow from 0001 as this is a hardened and battle tested impl.
In case of
cfi_cmdset_0001.c, program/erase is followed byinval_cache_and_wait_for_operation()to poll ready bit and based on status register value, success or the error handling is done.Most of the code corresponding to
inval_cache_and_wait_for_operation()is already incfi_cmdset_0002.c. So, whats missing in this patch is handling and reporting of errors as reflected in status register after write/erase failures. I will add that in the next version.But, I don't see much to borrow apart from error handling sequence. Please, let me know if I missed something.
Quoted 3 lines
I know other modern 0002 chips supports both old and new impl. of Status and I world guess that we will see more chips with new Status only.
Agreed. Newer devices would mostly be CFI 1.5.
--
Regards
Vignesh
Vignesh Raghavendra
maintainerRe: [RFC PATCH v2 1/5] mtd: cfi_cmdset_0002: Add support for polling status register
Quoted 33 lines · Joakim Tjernlund
Quoted 23 lines · Vignesh Raghavendra
CAUTION: This email originated from outside of the organization. Do not click links or open attachments unless you recognize the sender and know the content is safe.
Hi,
Quoted 17 lines · Joakim Tjernlund
Quoted 15 lines · Vignesh Raghavendra
HyperFlash devices are compliant with CFI AMD/Fujitsu Extended Command Set(0x0002) for flash operations, therefore
drivers/mtd/chips/cfi_cmdset_0002.ccan be use as is. But these devices do not support DQ polling method of determining chip ready/good status. These flashes provide Status Register whose bits can be polled to know status of flash operation.Cypress HyperFlash datasheet here[1], talks about CFI Amd/Fujitsu Extended Query version 1.5. Bit 0 of "Software Features supported" field of CFI Primary Vendor-Specific Extended Query table indicates presence/absence of status register and Bit 1 indicates whether or not DQ polling is supported. Using these bits, its possible to determine whether flash supports DQ polling or need to use Status Register.
Add support for polling status register to know device ready/status of erase/write operations when DQ polling is not supported.
Quoted 8 lines
Quoted 1 line
Isn't this new Status scheme just a copy of
Intels(cmdset_0001)?Yes, but with one difference: At the end of program/erase operation, device directly enters status register mode and starts reflecting status register content at any address.
The device remains in the read status register state until another command is written to the device. Therefore there is notion of device is in "status register read mode" (FL_STATUS) state
Quoted 8 lines
That seems to vary and long time ago RMK added this:
/* If the flash has finished erasing, then 'erase suspend' * appears to make some (28F320) flash devices switch to * 'read' mode. Make sure that we switch to 'read status' * mode so we get the right data. --rmk */ map_write(map, CMD(0x70), chip->in_progress_block_addr);
This behavior is expected with cmdset_0001. Because "The device remains in the read status register state until another command is written", therefore "erase suspend' command after erase completion will switch device to read mode. And therefore read status is safe thing to do for cmdset_0001.
But in case of cmdset_0002 erase completion will not put device to read status mode and therefore no special status tracking is required.
Quoted 6 lines
Quoted 4 lines
But in case of
cfi_cmdset_0002, once program/erase operation is complete, device returns to previous address space overlay from which operation was started from (mostly read mode)I hope you can do the same as Intel here, issue an explicit Status CMD or you will be in trouble.
Even if we issue Read Status command to enter read status mode, any single subsequent read will put device back to read mode. So, sending explicit Status CMD is of not much use.
As long as cmdset_0002 driver ensures sending Read Status cmd and next single read can be done in one go (ie. mutex held), I don't see any trouble here. This is already take care off.
Quoted 5 lines
Also, I think you need to use the various
map_word_xxxas in:
status =map_read(map, chip->in_progress_block_addr); if (map_word_andequal(map, status, status_OK, status_OK))break;
Yes, I will fixup this patch to use map_word_* wherever necessary in the next revision.
Quoted 3 lines
otherwise you will break interleaved setups(like two 8-bit flashes in parallel to form one 16 bit bus). Maybe this is not supported for CMDSET 0002 ?
Interleaved is indeed supported by cmdset_0002. Thanks for pointing that out!
Quoted 37 lines
Jocke
Quoted 34 lines
In order to enter status register overlay mode, Read Status command is to be written to
addr_unlock1(0x555)address. The overlay is in effect for one read access, specifically the next read access that follows the Status Register Read command
Therefore code aroundFL_STATUSstate incfi_cmdset_0001is not applicable tocfi_cmdset_0002as is.Quoted 3 lines
If so I think the new status impl. in 0002 should borrow from 0001 as this is a hardened and battle tested impl.
In case of
cfi_cmdset_0001.c, program/erase is followed byinval_cache_and_wait_for_operation()to poll ready bit and based on status register value, success or the error handling is done.Most of the code corresponding to
inval_cache_and_wait_for_operation()is already incfi_cmdset_0002.c. So, whats missing in this patch is handling and reporting of errors as reflected in status register after write/erase failures. I will add that in the next version.But, I don't see much to borrow apart from error handling sequence. Please, let me know if I missed something.
Quoted 3 lines
I know other modern 0002 chips supports both old and new impl. of Status and I world guess that we will see more chips with new Status only.
Agreed. Newer devices would mostly be CFI 1.5.
--
Regards
Vignesh
Signature · 6 lines
Regards Vignesh ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [RFC PATCH v2 1/5] mtd: cfi_cmdset_0002: Add support for polling status register
Quoted 59 lines · Vignesh Raghavendra
Quoted 33 lines · Joakim Tjernlund
Quoted 23 lines · Vignesh Raghavendra
CAUTION: This email originated from outside of the organization. Do not click links or open attachments unless you recognize the sender and know the content is safe.
Hi,
Quoted 17 lines · Joakim Tjernlund
Quoted 15 lines · Vignesh Raghavendra
HyperFlash devices are compliant with CFI AMD/Fujitsu Extended Command Set(0x0002) for flash operations, therefore
drivers/mtd/chips/cfi_cmdset_0002.ccan be use as is. But these devices do not support DQ polling method of determining chip ready/good status. These flashes provide Status Register whose bits can be polled to know status of flash operation.Cypress HyperFlash datasheet here[1], talks about CFI Amd/Fujitsu Extended Query version 1.5. Bit 0 of "Software Features supported" field of CFI Primary Vendor-Specific Extended Query table indicates presence/absence of status register and Bit 1 indicates whether or not DQ polling is supported. Using these bits, its possible to determine whether flash supports DQ polling or need to use Status Register.
Add support for polling status register to know device ready/status of erase/write operations when DQ polling is not supported.
Quoted 8 lines
Quoted 1 line
Isn't this new Status scheme just a copy of
Intels(cmdset_0001)?Yes, but with one difference: At the end of program/erase operation, device directly enters status register mode and starts reflecting status register content at any address.
The device remains in the read status register state until another command is written to the device. Therefore there is notion of device is in "status register read mode" (FL_STATUS) stateQuoted 8 lines
That seems to vary and long time ago RMK added this:
/* If the flash has finished erasing, then 'erase suspend' * appears to make some (28F320) flash devices switch to * 'read' mode. Make sure that we switch to 'read status' * mode so we get the right data. --rmk */ map_write(map, CMD(0x70), chip->in_progress_block_addr);This behavior is expected with
cmdset_0001. Because "The device remains in the read status register state until another command is written", therefore "erase suspend' command after erase completion will switch device to read mode. And therefore read status is safe thing to do forcmdset_0001.But in case of
cmdset_0002erase completion will not put device to read status mode and therefore no special status tracking is required.Quoted 5 lines
Quoted 3 lines
But in case of
cfi_cmdset_0002, once program/erase operation is complete, device returns to previous address space overlay from which operation was started from (mostly read mode)I hope you can do the same as Intel here, issue an explicit Status CMD or you will be in trouble.
Quoted 7 lines
Even if we issue Read Status command to enter read status mode, any single subsequent read will put device back to read mode. So, sending explicit Status CMD is of not much use.
As long as
cmdset_0002driver ensures sending Read Status cmd and next single read can be done in one go (ie. mutex held), I don't see any trouble here. This is already take care off.
Ouch, a non sticky Status sounds borken. Are you sure that nothing can change the chip between you issue the Status CMD and read out of status bits?
Like if an erase/suspend/resume completes just after Status CMD but before Status readout?
Jocke
Quoted 52 lines
Quoted 5 lines
Also, I think you need to use the various
map_word_xxxas in:
status =map_read(map, chip->in_progress_block_addr); if (map_word_andequal(map, status, status_OK, status_OK))break;Yes, I will fixup this patch to use map_word_* wherever necessary in the next revision.
Quoted 3 lines
otherwise you will break interleaved setups(like two 8-bit flashes in parallel to form one 16 bit bus). Maybe this is not supported for CMDSET 0002 ?
Interleaved is indeed supported by
cmdset_0002. Thanks for pointing that out!Quoted 35 lines
Jocke
Quoted 33 lines
In order to enter status register overlay mode, Read Status command is to be written to
addr_unlock1(0x555)address. The overlay is in effect for one read access, specifically the next read access that follows the Status Register Read command
Therefore code aroundFL_STATUSstate incfi_cmdset_0001is not applicable tocfi_cmdset_0002as is.Quoted 3 lines
If so I think the new status impl. in 0002 should borrow from 0001 as this is a hardened and battle tested impl.
In case of
cfi_cmdset_0001.c, program/erase is followed byinval_cache_and_wait_for_operation()to poll ready bit and based on status register value, success or the error handling is done.Most of the code corresponding to
inval_cache_and_wait_for_operation()is already incfi_cmdset_0002.c. So, whats missing in this patch is handling and reporting of errors as reflected in status register after write/erase failures. I will add that in the next version.But, I don't see much to borrow apart from error handling sequence. Please, let me know if I missed something.
Quoted 3 lines
I know other modern 0002 chips supports both old and new impl. of Status and I world guess that we will see more chips with new Status only.
Agreed. Newer devices would mostly be CFI 1.5.
--
Regards
Vignesh
Vignesh Raghavendra
maintainerRe: [RFC PATCH v2 1/5] mtd: cfi_cmdset_0002: Add support for polling status register
Quoted 64 lines · Joakim Tjernlund
Quoted 63 lines · Vignesh Raghavendra
Quoted 33 lines · Joakim Tjernlund
Quoted 23 lines · Vignesh Raghavendra
CAUTION: This email originated from outside of the organization. Do not click links or open attachments unless you recognize the sender and know the content is safe.
Hi,
Quoted 17 lines · Joakim Tjernlund
Quoted 15 lines · Vignesh Raghavendra
HyperFlash devices are compliant with CFI AMD/Fujitsu Extended Command Set(0x0002) for flash operations, therefore
drivers/mtd/chips/cfi_cmdset_0002.ccan be use as is. But these devices do not support DQ polling method of determining chip ready/good status. These flashes provide Status Register whose bits can be polled to know status of flash operation.Cypress HyperFlash datasheet here[1], talks about CFI Amd/Fujitsu Extended Query version 1.5. Bit 0 of "Software Features supported" field of CFI Primary Vendor-Specific Extended Query table indicates presence/absence of status register and Bit 1 indicates whether or not DQ polling is supported. Using these bits, its possible to determine whether flash supports DQ polling or need to use Status Register.
Add support for polling status register to know device ready/status of erase/write operations when DQ polling is not supported.
Quoted 8 lines
Quoted 1 line
Isn't this new Status scheme just a copy of
Intels(cmdset_0001)?Yes, but with one difference: At the end of program/erase operation, device directly enters status register mode and starts reflecting status register content at any address.
The device remains in the read status register state until another command is written to the device. Therefore there is notion of device is in "status register read mode" (FL_STATUS) stateQuoted 8 lines
That seems to vary and long time ago RMK added this:
/* If the flash has finished erasing, then 'erase suspend' * appears to make some (28F320) flash devices switch to * 'read' mode. Make sure that we switch to 'read status' * mode so we get the right data. --rmk */ map_write(map, CMD(0x70), chip->in_progress_block_addr);This behavior is expected with
cmdset_0001. Because "The device remains in the read status register state until another command is written", therefore "erase suspend' command after erase completion will switch device to read mode. And therefore read status is safe thing to do forcmdset_0001.But in case of
cmdset_0002erase completion will not put device to read status mode and therefore no special status tracking is required.Quoted 5 lines
Quoted 3 lines
But in case of
cfi_cmdset_0002, once program/erase operation is complete, device returns to previous address space overlay from which operation was started from (mostly read mode)I hope you can do the same as Intel here, issue an explicit Status CMD or you will be in trouble.
Even if we issue Read Status command to enter read status mode, any single subsequent read will put device back to read mode. So, sending explicit Status CMD is of not much use.
Quoted 8 lines
Quoted 3 lines
As long as
cmdset_0002driver ensures sending Read Status cmd and next single read can be done in one go (ie. mutex held), I don't see any trouble here. This is already take care off.Ouch, a non sticky Status sounds borken. Are you sure that nothing can change the chip between you issue the Status CMD and read out of status bits?
Like if an erase/suspend/resume completes just after Status CMD but before Status readout?
Yes, I did some tests(with HyperFlash) and erase/program completion/suspend in b/w issue of Status CMD but before status readout does not result in exiting status read address space overlay. So we are safe here with non sticky Status.
Signature · 6 lines
Regards Vignesh ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [RFC PATCH v2 1/5] mtd: cfi_cmdset_0002: Add support for polling status register
In reply to Vignesh RaghavendraHello!
Quoted 6 lines · Vignesh Raghavendra
HyperFlash devices are compliant with CFI AMD/Fujitsu Extended Command Set(0x0002) for flash operations, therefore
drivers/mtd/chips/cfi_cmdset_0002.ccan be use as is. But these devices do not support DQ polling method of determining chip ready/good status. These flashes provide Status Register whose bits can be polled to know status of flash operation.
Quoted 6 lines
Cypress HyperFlash datasheet here[1], talks about CFI Amd/Fujitsu Extended Query version 1.5. Bit 0 of "Software Features supported" field of CFI Primary Vendor-Specific Extended Query table indicates presence/absence of status register and Bit 1 indicates whether or not DQ polling is supported. Using these bits, its possible to determine whether flash supports DQ polling or need to use Status Register.
We need?
Quoted 15 lines
Add support for polling status register to know device ready/status of erase/write operations when DQ polling is not supported.
[1] https://www.cypress.com/file/213346/download
Signed-off-by Vignesh Raghavendra <[email protected]>--- drivers/mtd/chips/cfi_cmdset_0002.c | 50 +++++++++++++++++++++++++++++ include/linux/mtd/cfi.h | 5 +++ 2 files changed, 55 insertions(+)drivers/mtd/chips/cfi_cmdset_0002.c +0
-0
[...]
include/linux/mtd/cfi.h struct cfi_pri_amdstd { · line 236
Quoted 9 lines
include/linux/mtd/cfi.h +1
-0@@ -233,6 +233,11 @@ struct cfi_pri_amdstd {uint8_t VppMin;uint8_t VppMax;uint8_t TopBottom; +/* Below field are added from version 1.5 */
The below fields are.
include/linux/mtd/cfi.h struct cfi_pri_amdstd { · line 243
Quoted 8 lines
include/linux/mtd/cfi.h +4
-0+uint8_t ProgramSuspend; +uint8_t UnlockBypass; +uint8_t SecureSiliconSector; +uint8_t SoftwareFeatures; } __packed;/* Vendor-Specific PRI for Atmel chips (command set 0x0002) */
MBR, Sergei
Vignesh Raghavendra
maintainerRFC PATCH v2 2/5 dt-bindings: mtd: Add binding documentation for Hyperbus memory devices
In reply to Vignesh RaghavendraAdd DT binding documentation for Hyperbus memory devices. Only Hyperflash is supported at the moment.
--- Documentation/devicetree/bindings/mtd/cypress,hyperbus.txt | 6 ++++++ 1 file changed, 6 insertions(+) create mode 100644 Documentation/devicetree/bindings/mtd/cypress,hyperbus.txt
Documentation/devicetree/bindings/mtd/cypress,hyperbus.txt new file +6 -0
@@ -0,0 +1,6 @@ +Bindings for Hyperflash NOR flash chips compliant with Cypress Hyperbus +specification and supports Cypress CFI specification 1.5 command set. + +Required properties: +- compatible : "cypress,hyperflash" for Hyperflash NOR chips +- reg : Address where flash's memory mapped space
Signature · 1 line
2.21.0
Re: [RFC PATCH v2 2/5] dt-bindings: mtd: Add binding documentation for Hyperbus memory devices
Hello!
Quoted 15 lines · Vignesh Raghavendra
Add DT binding documentation for Hyperbus memory devices. Only Hyperflash is supported at the moment.
Signed-off-by Vignesh Raghavendra <[email protected]>--- Documentation/devicetree/bindings/mtd/cypress,hyperbus.txt | 6 ++++++ 1 file changed, 6 insertions(+) create mode 100644 Documentation/devicetree/bindings/mtd/cypress,hyperbus.txtDocumentation/devicetree/bindings/mtd/cypress,hyperbus.txt new file +0
-0
Documentation/devicetree/bindings/mtd/cypress,hyperbus.txt line 5
Quoted 5 lines
Documentation/devicetree/bindings/mtd/cypress,hyperbus.txt new file +5
-0@@ -0,0 +1,6 @@ +Bindings for Hyperflash NOR flash chips compliant with Cypress Hyperbus +specification and supports Cypress CFI specification 1.5 command set. + +Required properties: +- compatible : "cypress,hyperflash" for Hyperflash NOR chips
What about "cfi-flash", shouldn't it be also specified?
Documentation/devicetree/bindings/mtd/cypress,hyperbus.txt line 6
Quoted 1 line
Documentation/devicetree/bindings/mtd/cypress,hyperbus.txt new file +1
-0+- reg : Address where flash's memory mapped space
MBR, Sergei
Vignesh Raghavendra
maintainerRe: [RFC PATCH v2 2/5] dt-bindings: mtd: Add binding documentation for Hyperbus memory devices
Hi,
Quoted 13 lines · Sergei Shtylyov
Hello!
Quoted 9 lines · Vignesh Raghavendra
Add DT binding documentation for Hyperbus memory devices. Only Hyperflash is supported at the moment.
Signed-off-by Vignesh Raghavendra <[email protected]>--- Documentation/devicetree/bindings/mtd/cypress,hyperbus.txt | 6 ++++++ 1 file changed, 6 insertions(+) create mode 100644 Documentation/devicetree/bindings/mtd/cypress,hyperbus.txt
Quoted 13 lines
Documentation/devicetree/bindings/mtd/cypress,hyperbus.txt line 5
Quoted 11 lines
Documentation/devicetree/bindings/mtd/cypress,hyperbus.txt new file +5
-0@@ -0,0 +1,6 @@ +Bindings for Hyperflash NOR flash chips compliant with Cypress Hyperbus +specification and supports Cypress CFI specification 1.5 command set. + +Required properties: +- compatible : "cypress,hyperflash" for Hyperflash NOR chipsWhat about "cfi-flash", shouldn't it be also specified?
Oh, right. I missed that. Hyperflash is CFI compliant. Will add that next time. Thanks!
Quoted 5 lines
Documentation/devicetree/bindings/mtd/cypress,hyperbus.txt line 6
Quoted 2 lines
Documentation/devicetree/bindings/mtd/cypress,hyperbus.txt new file +1
-0+- reg : Address where flash's memory mapped spaceMBR, Sergei
Signature · 6 lines
Regards Vignesh ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Vignesh Raghavendra
maintainerRFC PATCH v2 3/5 mtd: Add support for Hyperbus memory devices
In reply to Vignesh RaghavendraCypress' Hyperbus is Low Signal Count, High Performance Double Data Rate Bus interface between a host system master and one or more slave interfaces. Hyperbus is used to connect microprocessor, microcontroller, or ASIC devices with random access NOR flash memory (called Hyperflash) or self refresh DRAM (called HyperRAM).
Its a 8-bit data bus (DQ[7:0]) with Read-Write Data Strobe (RWDS) signal and either Single-ended clock(3.0V parts) or Differential clock (1.8V parts). It uses ChipSelect lines to select b/w multiple slaves. At bus level, it follows a separate protocol described in Hyperbus specification[1].
Hyperflash follows CFI AMD/Fujitsu Extended Command Set (0x0002) similar to that of existing parallel NORs. Since Hyperbus is x8 DDR bus, its equivalent to x16 parallel NOR flash wrt bits per clock cycle. But Hyperbus operates at >166MHz frequencies.
HyperRAM provides direct random read/write access to flash memory array.
But, Hyperbus memory controllers seem to abstract implementation details and expose a simple MMIO interface to access connected flash.
Add support for registering Hyperflash devices with MTD framework. MTD maps framework along with CFI chip support framework are used to support communicating with flash.
Framework is modelled along the lines of spi-nor framework. Hyperbus memory controller (HBMC) drivers calls hyperbus_register_device() to register a single Hyperflash device. Hyperflash core parses MMIO access information from DT, sets up the map_info struct, probes CFI flash and registers it with MTD framework.
Some HBMC masters need calibration/training sequence[3] to be carried out, in order for DLL inside the controller to lock, by reading a known string/pattern. This is done by repeatedly reading CFI Query Identification String. Calibration needs to be done before trying to detect flash as part of CFI flash probe.
HyperRAM is not supported at the moment.
Hyperbus specification can be found at[1]
Hyperflash datasheet can be found at[2]
[1] https://www.cypress.com/file/213356/download
[2] https://www.cypress.com/file/213346/download
[3] http://www.ti.com/lit/ug/spruid7b/spruid7b.pdf
Table 12-5741. HyperFlash Access Sequence
--- MAINTAINERS | 7 + drivers/mtd/Kconfig | 2 + drivers/mtd/Makefile | 1 + drivers/mtd/hyperbus/Kconfig | 11 ++ drivers/mtd/hyperbus/Makefile | 3 + drivers/mtd/hyperbus/hyperbus-core.c | 183 +++++++++++++++++++++++++++ include/linux/mtd/hyperbus.h | 91 +++++++++++++ 7 files changed, 298 insertions(+) create mode 100644 drivers/mtd/hyperbus/Kconfig create mode 100644 drivers/mtd/hyperbus/Makefile create mode 100644 drivers/mtd/hyperbus/hyperbus-core.c create mode 100644 include/linux/mtd/hyperbus.h
MAINTAINERS +7 -0
@@ -7188,6 +7188,13 @@ F: include/uapi/linux/hyperv.h F: tools/hv/ F: Documentation/ABI/stable/sysfs-bus-vmbus +HYPERBUS SUPPORT +M: Vignesh Raghavendra <[email protected]> +S: Supported +F: drivers/mtd/hyperbus/ +F: include/linux/mtd/hyperbus.h +F: Documentation/devicetree/bindings/mtd/cypress,hyperbus.txt + HYPERVISOR VIRTUAL CONSOLE DRIVER L: [email protected] S: Odd Fixes
drivers/mtd/Kconfig +2 -0
@@ -290,4 +290,6 @@ source "drivers/mtd/spi-nor/Kconfig" source "drivers/mtd/ubi/Kconfig" +source "drivers/mtd/hyperbus/Kconfig" + endif # MTD
drivers/mtd/Makefile +1 -0
@@ -35,3 +35,4 @@ obj-y += chips/ lpddr/ maps/ devices/ nand/ tests/ obj-$(CONFIG_MTD_SPI_NOR) += spi-nor/ obj-$(CONFIG_MTD_UBI) += ubi/ +obj-$(CONFIG_MTD_HYPERBUS) += hyperbus/
drivers/mtd/hyperbus/Kconfig new file +11 -0
@@ -0,0 +1,11 @@ +menuconfig MTD_HYPERBUS + tristate "Hyperbus support" + select MTD_CFI + select MTD_MAP_BANK_WIDTH_2 + select MTD_CFI_AMDSTD + select MTD_COMPLEX_MAPPINGS + help + This is the framework for the Hyperbus which can be used by + the Hyperbus Controller driver to communicate with + Hyperflash. See Cypress Hyperbus specification for more + details
drivers/mtd/hyperbus/Makefile new file +3 -0
@@ -0,0 +1,3 @@ +# SPDX-License-Identifier: GPL-2.0 + +obj-$(CONFIG_MTD_HYPERBUS) += hyperbus-core.o
drivers/mtd/hyperbus/hyperbus-core.c new file +183 -0
183 lines not on this page · raw message
include/linux/mtd/hyperbus.h new file +91 -0
91 lines not on this page · raw message
Signature · 1 line
2.21.0
Re: [RFC PATCH v2 3/5] mtd: Add support for Hyperbus memory devices
Hello!
Quoted 1 line · Vignesh Raghavendra
Cypress' Hyperbus is Low Signal Count, High Performance Double Data Rate
It's HyperBus, according to the spec...
Quoted 10 lines
Bus interface between a host system master and one or more slave interfaces. Hyperbus is used to connect microprocessor, microcontroller, or ASIC devices with random access NOR flash memory (called Hyperflash) or self refresh DRAM (called HyperRAM).
Its a 8-bit data bus (DQ[7:0]) with Read-Write Data Strobe (RWDS) signal and either Single-ended clock(3.0V parts) or Differential clock (1.8V parts). It uses ChipSelect lines to select b/w multiple slaves. At bus level, it follows a separate protocol described in Hyperbus specification[1].
HyperBus.
Quoted 8 lines
Hyperflash follows CFI AMD/Fujitsu Extended Command Set (
0x0002) similar to that of existing parallel NORs. Since Hyperbus is x8 DDR bus, its equivalent to x16 parallel NOR flash wrt bits per clock cycle. But Hyperbus operates at >166MHz frequencies.
HyperRAM provides direct random read/write access to flash memory array.But, Hyperbus memory controllers seem to abstract implementation details
HyperBus.
Quoted 3 lines
and expose a simple MMIO interface to access connected flash.
Add support for registering Hyperflash devices with MTD framework. MTD
HyperFlash.
Quoted 4 lines
maps framework along with CFI chip support framework are used to support communicating with flash.
Framework is modelled along the lines of spi-nor framework. Hyperbus
HyperBus.
Quoted 2 lines
memory controller (HBMC) drivers calls
hyperbus_register_device()to register a single Hyperflash device. Hyperflash core parses MMIO access
HyperFlash.
Quoted 9 lines
information from DT, sets up the
map_infostruct, probes CFI flash and registers it with MTD framework.Some HBMC masters need calibration/training sequence[3] to be carried out, in order for DLL inside the controller to lock, by reading a known string/pattern. This is done by repeatedly reading CFI Query Identification String. Calibration needs to be done before trying to detect flash as part of CFI flash probe.
Quoted 4 lines
HyperRAM is not supported at the moment.
Hyperbus specification can be found at[1]
Hyperflash datasheet can be found at[2]
HyperBus & HyperFlash.
Quoted 6 lines
[1] https://www.cypress.com/file/213356/download
[2] https://www.cypress.com/file/213346/download
[3] http://www.ti.com/lit/ug/spruid7b/spruid7b.pdf
Table 12-5741. HyperFlash Access SequenceSigned-off-by Vignesh Raghavendra <[email protected]>
[...]
Quoted 13 lines
drivers/mtd/hyperbus/hyperbus-core.c new file +7
-0@@ -0,0 +1,183 @@ +// SPDX-License-Identifier: GPL-2.0 +// +// Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/ +// Author: Vignesh Raghavendra <[email protected]> + +#include <linux/err.h> +#include <linux/kernel.h>
drivers/mtd/hyperbus/hyperbus-core.c line 17
Quoted 10 lines
drivers/mtd/hyperbus/hyperbus-core.c new file +10
-0+#include <linux/module.h> +#include <linux/mtd/hyperbus.h> +#include <linux/mtd/map.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/cfi.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/types.h> + +#define HYPERBUS_CALIB_COUNT 25
As I said, this seems platform specific...
[...]
drivers/mtd/hyperbus/hyperbus-core.c line 62
Quoted 1 line
drivers/mtd/hyperbus/hyperbus-core.c new file +1
-0+/* Default calibration routine for use by Hyperbus controller.
No, there should be easy opt-out from the calibration method.
Currently, the driver will have to define its own calibrate method, even if does't need any calibration...
Quoted 9 lines
drivers/mtd/hyperbus/hyperbus-core.c new file +9
-0+* Controller is calibrated by repeatedly reading known pattern ("QRY" +* string from CFI space) +* It is not enough to just ensure "QRY" string is read correctly, need +* to read mulitple times to ensure stability of the DLL lock. +*/ +int hyperbus_calibrate (struct hyperbus_device *hbdev) +{ +struct map_info *map = &hbdev->map; +struct cfi_private cfi;
drivers/mtd/hyperbus/hyperbus-core.c line 81
Quoted 10 lines
drivers/mtd/hyperbus/hyperbus-core.c new file +10
-0+int count =HYPERBUS_CALIB_COUNT ; +int ret; + + cfi.interleave =1 ; + cfi.device_type =CFI_DEVICETYPE_X16 ; +cfi_send_gen_cmd (0xF0 ,0 ,0 , map, &cfi, cfi.device_type,NULL ); +cfi_send_gen_cmd (0x98 ,0x55 ,0 , map, &cfi, cfi.device_type,NULL ); + +while (count--) +cfi_qry_present (map,0 , &cfi);
I still don't understand why we have to spin all 25 times here if QRY
appears earlier than that.
Quoted 7 lines
drivers/mtd/hyperbus/hyperbus-core.c new file +7
-0+ + ret =cfi_qry_present (map,0 , &cfi); +cfi_qry_mode_off (0 , map, &cfi); + +return ret; +} +EXPORT_SYMBOL_GPL (hyperbus_calibrate);
[...]
Quoted 13 lines
include/linux/mtd/hyperbus.h new file +7
-0@@ -0,0 +1,91 @@ +/* SPDX-License-Identifier: GPL-2.0 +* +* Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/ +*/ + +#ifndef __LINUX_MTD_HYPERBUS_H__ +#define __LINUX_MTD_HYPERBUS_H__
include/linux/mtd/hyperbus.h line 17
Quoted 10 lines
include/linux/mtd/hyperbus.h new file +10
-0+ +#include <linux/mtd/map.h> + +enum hyperbus_memtype { +HYPERFLASH , +HYPERRAM , +}; + +/** +* struct hyerbus_device - struct representing Hyperbus slave device
hyperbus_device.
include/linux/mtd/hyperbus.h line 22
Quoted 5 lines
include/linux/mtd/hyperbus.h new file +5
-0+* @map: map_info struct for accessing MMIO Hyperbus flash memory +* @np: pointer to Hyperbus slave device node +* @mtd: pointer to MTD struct +* @ctlr: pointer to Hyperbus controller struct +* @memtype: type of memory device: Hyperflash or HyperRAM
HyperFlash.
[...]
include/linux/mtd/hyperbus.h line 69
Quoted 3 lines
include/linux/mtd/hyperbus.h new file +3
-0+/** +* hyperbus_calibrate - default calibration routine for use by Hyperbus ctlr. +* @hbdev: hyperbus_device to be used for calibration
HyperBus.
[...]
MBR, Sergei
Re: [RFC PATCH v2 3/5] mtd: Add support for Hyperbus memory devices
Quoted 94 lines · Sergei Shtylyov
Quoted 1 line
Cypress' Hyperbus is Low Signal Count, High Performance Double Data Rate
It's HyperBus, according to the spec...
Quoted 10 lines
Bus interface between a host system master and one or more slave interfaces. Hyperbus is used to connect microprocessor, microcontroller, or ASIC devices with random access NOR flash memory (called Hyperflash) or self refresh DRAM (called HyperRAM).
Its a 8-bit data bus (DQ[7:0]) with Read-Write Data Strobe (RWDS) signal and either Single-ended clock(3.0V parts) or Differential clock (1.8V parts). It uses ChipSelect lines to select b/w multiple slaves. At bus level, it follows a separate protocol described in Hyperbus specification[1].
HyperBus.
Quoted 8 lines
Hyperflash follows CFI AMD/Fujitsu Extended Command Set (
0x0002) similar to that of existing parallel NORs. Since Hyperbus is x8 DDR bus, its equivalent to x16 parallel NOR flash wrt bits per clock cycle. But Hyperbus operates at >166MHz frequencies.
HyperRAM provides direct random read/write access to flash memory array.But, Hyperbus memory controllers seem to abstract implementation details
HyperBus.
Quoted 3 lines
and expose a simple MMIO interface to access connected flash.
Add support for registering Hyperflash devices with MTD framework. MTD
HyperFlash.
Quoted 4 lines
maps framework along with CFI chip support framework are used to support communicating with flash.
Framework is modelled along the lines of spi-nor framework. Hyperbus
HyperBus.
Quoted 2 lines
memory controller (HBMC) drivers calls
hyperbus_register_device()to register a single Hyperflash device. Hyperflash core parses MMIO accessHyperFlash.
Quoted 9 lines
information from DT, sets up the
map_infostruct, probes CFI flash and registers it with MTD framework.Some HBMC masters need calibration/training sequence[3] to be carried out, in order for DLL inside the controller to lock, by reading a known string/pattern. This is done by repeatedly reading CFI Query Identification String. Calibration needs to be done before trying to detect flash as part of CFI flash probe.
Quoted 4 lines
HyperRAM is not supported at the moment.
Hyperbus specification can be found at[1]
Hyperflash datasheet can be found at[2]HyperBus & HyperFlash.
Quoted 6 lines
[1] https://www.cypress.com/file/213356/download
[2] https://www.cypress.com/file/213346/download
[3] http://www.ti.com/lit/ug/spruid7b/spruid7b.pdf
Table 12-5741. HyperFlash Access SequenceSigned-off-by Vignesh Raghavendra <[email protected]>[...]
Quoted 13 lines
drivers/mtd/hyperbus/hyperbus-core.c new file +7
-0@@ -0,0 +1,183 @@ +// SPDX-License-Identifier: GPL-2.0 +// +// Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/ +// Author: Vignesh Raghavendra <[email protected]> + +#include <linux/err.h> +#include <linux/kernel.h> drivers/mtd/hyperbus/hyperbus-core.c line 17
Quoted 10 lines
drivers/mtd/hyperbus/hyperbus-core.c new file +10
-0+#include <linux/module.h> +#include <linux/mtd/hyperbus.h> +#include <linux/mtd/map.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/cfi.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/types.h> + +#define HYPERBUS_CALIB_COUNT 25As I said, this seems platform specific...
Quoted 6 lines
[...]
Quoted 1 line
+/* Default calibration routine for use by Hyperbus controller.
No, there should be easy opt-out from the calibration method.
Currently, the driver will have to define its own calibrate method, even if does't need any calibration...
Nevermind -- the method ptr can be NULL, of course, so there's easy opt-out...
[...]
MBR, Sergei
Vignesh Raghavendra
maintainerRFC PATCH v2 4/5 dt-bindings: mtd: Add bindings for TI's AM654 Hyperbus memory controller
In reply to Vignesh RaghavendraAdd binding documentation for TI's Hyperbus memory controller present on AM654 SoC.
--- .../devicetree/bindings/mtd/ti,am654-hbmc.txt | 27 +++++++++++++++++++ MAINTAINERS | 1 + 2 files changed, 28 insertions(+) create mode 100644 Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt
Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt new file +27 -0
@@ -0,0 +1,27 @@ +Bindings for Hyperbus Memory Controller on TI's K3 family of SoCs + +Required properties: +- compatible : "ti,am654-hbmc" for AM654 SoC +- reg : Two entries: + First entry pointed to the register space of HBMC controller + Second entry pointing to the memory map region dedicated for + MMIO access to attached flash devices +- ranges : Address range allocated for each Chipselect in the MMIO space + +Example: + hbmc: hbmc@47034000 { + compatible = "ti,am654-hbmc"; + reg = <0x0 0x47034000 0x0 0x100>, + <0x5 0x00000000 0x1 0x0000000>; + power-domains = <&k3_pds 55>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x5 0x00000000 0x4000000>, /* CS0 - 64MB */ + <0x1 0x5 0x04000000 0x4000000>; /* CS1 - 64MB + + /* Slave flash node */ + flash@0{ + compatible = "cypress,hyperflash"; + reg = <0x0 0x4000000>; + }; + };
MAINTAINERS +1 -0
@@ -7194,6 +7194,7 @@ S: Supported F: drivers/mtd/hyperbus/ F: include/linux/mtd/hyperbus.h F: Documentation/devicetree/bindings/mtd/cypress,hyperbus.txt +F: Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt HYPERVISOR VIRTUAL CONSOLE DRIVER L: [email protected]
Signature · 1 line
2.21.0
Vignesh Raghavendra
maintainerRFC PATCH v2 5/5 mtd: hyperbus: Add driver for TI's Hyperbus memory controller
In reply to Vignesh RaghavendraAdd driver for Hyperbus memory controller on TI's AM654 SoC. Programming IP is pretty simple and provides direct memory mapped access to connected Flash devices.
Add basic support for the IP without DMA. Second ChipSelect is not supported for now.
--- drivers/mtd/hyperbus/Kconfig | 10 +++ drivers/mtd/hyperbus/Makefile | 1 + drivers/mtd/hyperbus/hbmc_am654.c | 108 ++++++++++++++++++++++++++++++ 3 files changed, 119 insertions(+) create mode 100644 drivers/mtd/hyperbus/hbmc_am654.c
drivers/mtd/hyperbus/Kconfig +10 -0
@@ -9,3 +9,13 @@ menuconfig MTD_HYPERBUS the Hyperbus Controller driver to communicate with Hyperflash. See Cypress Hyperbus specification for more details + +if MTD_HYPERBUS + +config HBMC_AM654 + tristate "Hyperbus controller driver for AM65x SoC" + help + This is the driver for Hyperbus controller on TI's AM65x and + other SoCs + +endif # MTD_HYPERBUS
drivers/mtd/hyperbus/Makefile +1 -0
@@ -1,3 +1,4 @@ # SPDX-License-Identifier: GPL-2.0 obj-$(CONFIG_MTD_HYPERBUS) += hyperbus-core.o +obj-$(CONFIG_HBMC_AM654) += hbmc_am654.o
drivers/mtd/hyperbus/hbmc_am654.c new file +108 -0
108 lines not on this page · raw message
Signature · 1 line
2.21.0
Re: [RFC PATCH v2 5/5] mtd: hyperbus: Add driver for TI's Hyperbus memory controller
Quoted 8 lines · Vignesh Raghavendra
Add driver for Hyperbus memory controller on TI's AM654 SoC. Programming IP is pretty simple and provides direct memory mapped access to connected Flash devices.
Add basic support for the IP without DMA. Second ChipSelect is not supported for now.
Signed-off-by Vignesh Raghavendra <[email protected]>
[...]
Quoted 45 lines
drivers/mtd/hyperbus/Makefile +1
-0@@ -1,3 +1,4 @@ # SPDX-License-Identifier: GPL-2.0 obj-$(CONFIG_MTD_HYPERBUS) += hyperbus-core.o +obj-$(CONFIG_HBMC_AM654) += hbmc_am654.odrivers/mtd/hyperbus/hbmc_am654.c new file +30
-0@@ -0,0 +1,108 @@ +// SPDX-License-Identifier: GPL-2.0 +// +// Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/ +// Author: Vignesh Raghavendra <[email protected]> + +#include <linux/err.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/mtd/hyperbus.h> +#include <linux/mtd/mtd.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/pm_runtime.h> +#include <linux/types.h> + +struct am654_hbmc_priv { +struct hyperbus_ctlr ctlr; +struct hyperbus_device hbdev; +void __iomem *regbase; +}; + +static const struct hyperbus_ops am654_hbmc_ops = { + .calibrate = hyperbus_calibrate, +}; + +static int am654_hbmc_probe (struct platform_device *pdev) +{ +struct device *dev = &pdev->dev; +struct am654_hbmc_priv *priv; +struct resource *res;
drivers/mtd/hyperbus/hbmc_am654.c line 40
Quoted 10 lines
drivers/mtd/hyperbus/hbmc_am654.c new file +10
-0+int ret; + + priv =devm_kzalloc (&pdev->dev,sizeof (*priv),GFP_KERNEL ); +if (!priv) +return -ENOMEM ; + +platform_set_drvdata (pdev, priv); + + res =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); +if (!res) {
This is redundant as devm_ioremap_resource() checks for !res anyway.
drivers/mtd/hyperbus/hbmc_am654.c line 45
Quoted 5 lines
drivers/mtd/hyperbus/hbmc_am654.c new file +5
-0+dev_err (&pdev->dev,"failed to get memory resource\n" ); +return -ENOENT ; + } + + priv->regbase =devm_ioremap_resource (dev, res);
BTW, there's devm_platform_ioremap_resource() now...
[...]
MBR, Sergei