Skip to contentSkip to conversation

Add support for PCIe RC and EP mode in TI's AM654 SoC

PATCH Superseded Kishon Vijay Abraham I 3 participants 33 messages Mar 25, 2019 – Apr 16, 2019

Subsystems (8)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

v2 cover Add support for PCIe RC and EP mode in TI's AM654 SoC

Add PCIe RC support for TI's AM654 SoC. The PCIe controller in AM654 uses Synopsys core revision 4.90a and uses the same TI wrapper as used in keystone2 with certain modification. Hence AM654 will use the same pci wrapper driver pci-keystone.c

This series was initially part of [1]. This series only includes patches that has to be merged via Lorenzo's tree. The PHY patches and dt patches will be sent separately.

This series is created over keystone MSI cleanup series [2].

This series:
*) Cleanup pci-keystone driver so that both RC mode and EP mode of
AM654 can be supported
*) Modify epc-core to support allocation of aligned buffers required for
AM654
*) Fix ATU unroll identification
*) Add support for both host mode and device mode in AM654

Changes from v1:
*) Support for legacy interrupt in AM654 is removed (see backgrond here [3]) *) Allow of_pci_get_max_link_speed to be used by Endpoint controller driver
*) Add support to set max-link-speed from DT in pci-keystone driver *) Update "Reviewed-by: Rob Herring <[email protected]>" tags.

[1] -> https://lore.kernel.org/patchwork/cover/989487/
[2] -> https://lkml.org/lkml/2019/3/21/193
[3] -> https://lkml.org/lkml/2019/3/19/235

Kishon Vijay Abraham I (26):
PCI: keystone: Add start_link/stop_link dw_pcie_ops
PCI: keystone: Cleanup error_irq configuration
dt-bindings: PCI: keystone: Add "reg-names" binding information
PCI: keystone: Perform host initialization in a single function
PCI: keystone: Use platform_get_resource_byname to get memory
resources
PCI: keystone: Move initializations to appropriate places
dt-bindings: PCI: Add dt-binding to configure PCIe mode
PCI: keystone: Explicitly set the PCIe mode
dt-bindings: PCI: Document "atu" reg-names
PCI: dwc: Enable iATU unroll for endpoint too
PCI: dwc: Fix ATU identification for designware version >= 4.80
PCI: keystone: Prevent ARM32 specific code to be compiled for ARM64
dt-bindings: PCI: Add PCI RC dt binding documentation for AM654
PCI: keystone: Add support for PCIe RC in AM654x Platforms
PCI: keystone: Invoke phy_reset API before enabling PHY
PCI: OF: Allow of_pci_get_max_link_speed() to be used by PCI Endpoint
drivers
PCI: keystone: Add support to set the max link speed from DT
PCI: endpoint: Add support to allocate aligned buffers to be mapped in
BARs
PCI: dwc: Add const qualifier to struct dw_pcie_ep_ops
PCI: dwc: Fix dw_pcie_ep_find_capability to return correct capability
offset
PCI: dwc: Add callbacks for accessing dbi2 address space
PCI: keystone: Add support for PCIe EP in AM654x Platforms
PCI: designware-ep: Configure RESBAR to advertise the smallest size
PCI: designware-ep: Use aligned ATU window for raising MSI interrupts
misc: pci_endpoint_test: Add support to test PCI EP in AM654x
misc: pci_endpoint_test: Fix test_reg_bar to be updated in
pci_endpoint_test

 .../bindings/pci/designware-pcie.txt          |   7 +-
 .../devicetree/bindings/pci/pci-keystone.txt  |  14 +-
 drivers/misc/pci_endpoint_test.c              |  18 +
 drivers/pci/Makefile                          |   2 +-
 drivers/pci/controller/dwc/Kconfig            |  25 +-
 drivers/pci/controller/dwc/pci-dra7xx.c       |   2 +-
 drivers/pci/controller/dwc/pci-keystone.c     | 577 +++++++++++++++---
 drivers/pci/controller/dwc/pcie-artpec6.c     |   2 +-
 .../pci/controller/dwc/pcie-designware-ep.c   |  55 +-
 .../pci/controller/dwc/pcie-designware-host.c |  19 -
 .../pci/controller/dwc/pcie-designware-plat.c |   2 +-
 drivers/pci/controller/dwc/pcie-designware.c  |  52 ++
 drivers/pci/controller/dwc/pcie-designware.h  |  15 +-
 drivers/pci/endpoint/functions/pci-epf-test.c |   5 +-
 drivers/pci/endpoint/pci-epf-core.c           |  10 +-
 drivers/pci/of.c                              |  44 +-
 include/linux/pci-epc.h                       |   2 +
 include/linux/pci-epf.h                       |   3 +-
 18 files changed, 682 insertions(+), 172 deletions(-)
Signature · 1 line
2.17.1
#1 lore raw

PATCH v2 1/26 PCI: keystone: Add start_link/stop_link dw_pcie_ops

Add start_link/stop_link dw_pcie_ops and invoke ks_pcie_start_link directly from host_init. start_link/stop_link ops is required for adding EP mode support.

---
 drivers/pci/controller/dwc/pci-keystone.c | 44 +++++++++++------------
 1 file changed, 22 insertions(+), 22 deletions(-)
drivers/pci/controller/dwc/pci-keystone.c +22 -22
index b757692e2848..07f55b355d75 100644
@@ -460,18 +460,33 @@ static int ks_pcie_link_up(struct dw_pcie *pci)
 	return (val == PORT_LOGIC_LTSSM_STATE_L0);
 }
 
-static void ks_pcie_initiate_link_train(struct keystone_pcie *ks_pcie)
+static void ks_pcie_stop_link(struct dw_pcie *pci)
 {
+	struct keystone_pcie *ks_pcie = to_keystone_pcie(pci);
 	u32 val;
 
 	/* Disable Link training */
 	val = ks_pcie_app_readl(ks_pcie, CMD_STATUS);
 	val &= ~LTSSM_EN_VAL;
 	ks_pcie_app_writel(ks_pcie, CMD_STATUS, LTSSM_EN_VAL | val);
+}
+
+static int ks_pcie_start_link(struct dw_pcie *pci)
+{
+	struct keystone_pcie *ks_pcie = to_keystone_pcie(pci);
+	struct device *dev = pci->dev;
+	u32 val;
+
+	if (dw_pcie_link_up(pci)) {
+		dev_dbg(dev, "link is already up\n");
+		return 0;
+	}
 
 	/* Initiate Link Training */
 	val = ks_pcie_app_readl(ks_pcie, CMD_STATUS);
 	ks_pcie_app_writel(ks_pcie, CMD_STATUS, LTSSM_EN_VAL | val);
+
+	return 0;
 }
 
 /**
@@ -556,26 +571,6 @@ static void ks_pcie_quirk(struct pci_dev *dev)
 }
 DECLARE_PCI_FIXUP_ENABLE(PCI_ANY_ID, PCI_ANY_ID, ks_pcie_quirk);
 
-static int ks_pcie_establish_link(struct keystone_pcie *ks_pcie)
-{
-	struct dw_pcie *pci = ks_pcie->pci;
-	struct device *dev = pci->dev;
-
-	if (dw_pcie_link_up(pci)) {
-		dev_info(dev, "Link already up\n");
-		return 0;
-	}
-
-	ks_pcie_initiate_link_train(ks_pcie);
-
-	/* check if the link is up or not */
-	if (!dw_pcie_wait_for_link(pci))
-		return 0;
-
-	dev_err(dev, "phy link never came up\n");
-	return -ETIMEDOUT;
-}
-
 static void ks_pcie_msi_irq_handler(struct irq_desc *desc)
 {
 	unsigned int irq = desc->irq_data.hwirq;
@@ -813,7 +808,7 @@ static int __init ks_pcie_host_init(struct pcie_port *pp)
 
 	dw_pcie_setup_rc(pp);
 
-	ks_pcie_establish_link(ks_pcie);
+	ks_pcie_stop_link(pci);
 	ks_pcie_setup_rc_app_regs(ks_pcie);
 	ks_pcie_setup_interrupts(ks_pcie);
 	writew(PCI_IO_RANGE_TYPE_32 | (PCI_IO_RANGE_TYPE_32 << 8),
@@ -830,6 +825,9 @@ static int __init ks_pcie_host_init(struct pcie_port *pp)
 	hook_fault_code(17, ks_pcie_fault, SIGBUS, 0,
 			"Asynchronous external abort");
 
+	ks_pcie_start_link(pci);
+	dw_pcie_wait_for_link(pci);
+
 	return 0;
 }
 
@@ -892,6 +890,8 @@ static const struct of_device_id ks_pcie_of_match[] = {
 };
 
 static const struct dw_pcie_ops ks_pcie_dw_pcie_ops = {
+	.start_link = ks_pcie_start_link,
+	.stop_link = ks_pcie_stop_link,
 	.link_up = ks_pcie_link_up,
 };
 
Signature · 1 line
2.17.1
#2 lore raw

PATCH v2 2/26 PCI: keystone: Cleanup error_irq configuration

In reply to Kishon Vijay Abraham I

pci-keystone driver uses irq_of_parse_and_map to get irq number of error_irq. Use platform_get_irq instead and move platform_get_irq() and request_irq() of error_irq from ks_pcie_add_pcie_port to ks_pcie_probe since error_irq is common to both RC mode and EP mode.

---
 drivers/pci/controller/dwc/pci-keystone.c | 43 +++++++++--------------
 1 file changed, 17 insertions(+), 26 deletions(-)
drivers/pci/controller/dwc/pci-keystone.c +17 -26
index 07f55b355d75..e50f8773e768 100644
@@ -98,8 +98,6 @@ struct keystone_pcie {
 	struct irq_domain	*legacy_irq_domain;
 	struct device_node	*np;
 
-	int error_irq;
-
 	/* Application register space */
 	void __iomem		*va_app_base;	/* DT 1st resource */
 	struct resource		app;
@@ -743,12 +741,6 @@ static int ks_pcie_config_legacy_irq(struct keystone_pcie *ks_pcie)
 	return ret;
 }
 
-static void ks_pcie_setup_interrupts(struct keystone_pcie *ks_pcie)
-{
-	if (ks_pcie->error_irq > 0)
-		ks_pcie_enable_error_irq(ks_pcie);
-}
-
 /*
  * When a PCI device does not exist during config cycles, keystone host gets a
  * bus error instead of returning 0xffffffff. This handler always returns 0
@@ -810,7 +802,6 @@ static int __init ks_pcie_host_init(struct pcie_port *pp)
 
 	ks_pcie_stop_link(pci);
 	ks_pcie_setup_rc_app_regs(ks_pcie);
-	ks_pcie_setup_interrupts(ks_pcie);
 	writew(PCI_IO_RANGE_TYPE_32 | (PCI_IO_RANGE_TYPE_32 << 8),
 			pci->dbi_base + PCI_IO_BASE);
 
@@ -854,23 +845,6 @@ static int __init ks_pcie_add_pcie_port(struct keystone_pcie *ks_pcie,
 	struct device *dev = &pdev->dev;
 	int ret;
 
-	/*
-	 * Index 0 is the platform interrupt for error interrupt
-	 * from RC.  This is optional.
-	 */
-	ks_pcie->error_irq = irq_of_parse_and_map(ks_pcie->np, 0);
-	if (ks_pcie->error_irq <= 0)
-		dev_info(dev, "no error IRQ defined\n");
-	else {
-		ret = request_irq(ks_pcie->error_irq, ks_pcie_err_irq_handler,
-				  IRQF_SHARED, "pcie-error-irq", ks_pcie);
-		if (ret < 0) {
-			dev_err(dev, "failed to request error IRQ %d\n",
-				ks_pcie->error_irq);
-			return ret;
-		}
-	}
-
 	pp->ops = &ks_pcie_host_ops;
 	ret = ks_pcie_dw_host_init(ks_pcie);
 	if (ret) {
@@ -946,6 +920,7 @@ static int __init ks_pcie_probe(struct platform_device *pdev)
 	u32 num_lanes;
 	char name[10];
 	int ret;
+	int irq;
 	int i;
 
 	ks_pcie = devm_kzalloc(dev, sizeof(*ks_pcie), GFP_KERNEL);
@@ -965,6 +940,20 @@ static int __init ks_pcie_probe(struct platform_device *pdev)
 		return ret;
 	}
 
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(dev, "missing IRQ resource: %d\n", irq);
+		return irq;
+	}
+
+	ret = request_irq(irq, ks_pcie_err_irq_handler, IRQF_SHARED,
+			  "ks-pcie-error-irq", ks_pcie);
+	if (ret < 0) {
+		dev_err(dev, "failed to request error IRQ %d\n",
+			irq);
+		return ret;
+	}
+
 	ret = of_property_read_u32(np, "num-lanes", &num_lanes);
 	if (ret)
 		num_lanes = 1;
@@ -1020,6 +1009,8 @@ static int __init ks_pcie_probe(struct platform_device *pdev)
 	if (ret < 0)
 		goto err_get_sync;
 
+	ks_pcie_enable_error_irq(ks_pcie);
+
 	return 0;
 
 err_get_sync:
Signature · 1 line
2.17.1
#3 lore raw

PATCH v2 3/26 dt-bindings: PCI: keystone: Add "reg-names" binding information

In reply to Kishon Vijay Abraham I

Add "reg-names" binding information in order for device tree node to be populated with the correct register strings. This will break old dt compatibility. However Keystone PCI has never worked in upstream kernel due to lack of SERDES support. Before SERDES support is added, cleanup the Keystone PCI dt-bindngs. This new binding will also be used by PCI in AM654 platform.

---
 Documentation/devicetree/bindings/pci/pci-keystone.txt | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
Documentation/devicetree/bindings/pci/pci-keystone.txt +4 -2
index 2030ee0dc4f9..3a551687cfa2 100644
@@ -12,8 +12,10 @@ described here as well as properties that are not applicable.
 Required Properties:-
 
 compatibility: "ti,keystone-pcie"
-reg:	index 1 is the base address and length of DW application registers.
-	index 2 is the base address and length of PCI device ID register.
+reg: Three register ranges as listed in the reg-names property
+reg-names: "dbics" for the DesignWare PCIe registers, "app" for the
+	   TI specific application registers, "config" for the
+	   configuration space address
 
 pcie_msi_intc : Interrupt controller device node for MSI IRQ chip
 	interrupt-cells: should be set to 1
Signature · 1 line
2.17.1
#4 lore raw

PATCH v2 4/26 PCI: keystone: Perform host initialization in a single function

In reply to Kishon Vijay Abraham I

No functional change. Instead of having two functions ks_pcie_add_pcie_port and ks_pcie_dw_host_init for initializing host, have a single function to perform all the host initialization.

---
 drivers/pci/controller/dwc/pci-keystone.c | 63 +++++++++--------------
 1 file changed, 23 insertions(+), 40 deletions(-)
drivers/pci/controller/dwc/pci-keystone.c +23 -40
index e50f8773e768..566718ea7ebf 100644
@@ -487,45 +487,6 @@ static int ks_pcie_start_link(struct dw_pcie *pci)
 	return 0;
 }
 
-/**
- * ks_pcie_dw_host_init() - initialize host for v3_65 dw hardware
- *
- * Ioremap the register resources, initialize legacy irq domain
- * and call dw_pcie_v3_65_host_init() API to initialize the Keystone
- * PCI host controller.
- */
-static int __init ks_pcie_dw_host_init(struct keystone_pcie *ks_pcie)
-{
-	struct dw_pcie *pci = ks_pcie->pci;
-	struct pcie_port *pp = &pci->pp;
-	struct device *dev = pci->dev;
-	struct platform_device *pdev = to_platform_device(dev);
-	struct resource *res;
-
-	/* Index 0 is the config reg. space address */
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	pci->dbi_base = devm_pci_remap_cfg_resource(dev, res);
-	if (IS_ERR(pci->dbi_base))
-		return PTR_ERR(pci->dbi_base);
-
-	/*
-	 * We set these same and is used in pcie rd/wr_other_conf
-	 * functions
-	 */
-	pp->va_cfg0_base = pci->dbi_base + SPACE0_REMOTE_CFG_OFFSET;
-	pp->va_cfg1_base = pp->va_cfg0_base;
-
-	/* Index 1 is the application reg. space address */
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-	ks_pcie->va_app_base = devm_ioremap_resource(dev, res);
-	if (IS_ERR(ks_pcie->va_app_base))
-		return PTR_ERR(ks_pcie->va_app_base);
-
-	ks_pcie->app = *res;
-
-	return dw_pcie_host_init(pp);
-}
-
 static void ks_pcie_quirk(struct pci_dev *dev)
 {
 	struct pci_bus *bus = dev->bus;
@@ -843,10 +804,32 @@ static int __init ks_pcie_add_pcie_port(struct keystone_pcie *ks_pcie,
 	struct dw_pcie *pci = ks_pcie->pci;
 	struct pcie_port *pp = &pci->pp;
 	struct device *dev = &pdev->dev;
+	struct resource *res;
 	int ret;
 
+	/* Index 0 is the config reg. space address */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	pci->dbi_base = devm_pci_remap_cfg_resource(dev, res);
+	if (IS_ERR(pci->dbi_base))
+		return PTR_ERR(pci->dbi_base);
+
+	/*
+	 * We set these same and is used in pcie rd/wr_other_conf
+	 * functions
+	 */
+	pp->va_cfg0_base = pci->dbi_base + SPACE0_REMOTE_CFG_OFFSET;
+	pp->va_cfg1_base = pp->va_cfg0_base;
+
+	/* Index 1 is the application reg. space address */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	ks_pcie->va_app_base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(ks_pcie->va_app_base))
+		return PTR_ERR(ks_pcie->va_app_base);
+
+	ks_pcie->app = *res;
+
 	pp->ops = &ks_pcie_host_ops;
-	ret = ks_pcie_dw_host_init(ks_pcie);
+	ret = dw_pcie_host_init(pp);
 	if (ret) {
 		dev_err(dev, "failed to initialize host\n");
 		return ret;
Signature · 1 line
2.17.1
#5 lore raw

PATCH v2 5/26 PCI: keystone: Use platform_get_resource_byname to get memory resources

In reply to Kishon Vijay Abraham I

Use platform_get_resource_byname() instead of platform_get_resource() which uses index to get memory resources. While at that get the memory resource defined specifically for configuration space instead of deriving the configuration space address from dbics address space. Since pci-keystone driver has never worked out of the box in mainline kernel, dt backward compatibility is ignored.

---
 drivers/pci/controller/dwc/pci-keystone.c | 17 +++++++----------
 1 file changed, 7 insertions(+), 10 deletions(-)
drivers/pci/controller/dwc/pci-keystone.c +7 -10
index 566718ea7ebf..5eebef9b9ada 100644
@@ -44,7 +44,6 @@
 #define CFG_TYPE1			BIT(24)
 
 #define OB_SIZE				0x030
-#define SPACE0_REMOTE_CFG_OFFSET	0x1000
 #define OB_OFFSET_INDEX(n)		(0x200 + (8 * (n)))
 #define OB_OFFSET_HI(n)			(0x204 + (8 * (n)))
 #define OB_ENABLEN			BIT(0)
@@ -807,21 +806,19 @@ static int __init ks_pcie_add_pcie_port(struct keystone_pcie *ks_pcie,
 	struct resource *res;
 	int ret;
 
-	/* Index 0 is the config reg. space address */
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbics");
 	pci->dbi_base = devm_pci_remap_cfg_resource(dev, res);
 	if (IS_ERR(pci->dbi_base))
 		return PTR_ERR(pci->dbi_base);
 
-	/*
-	 * We set these same and is used in pcie rd/wr_other_conf
-	 * functions
-	 */
-	pp->va_cfg0_base = pci->dbi_base + SPACE0_REMOTE_CFG_OFFSET;
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "config");
+	pp->va_cfg0_base = devm_pci_remap_cfg_resource(dev, res);
+	if (IS_ERR(pp->va_cfg0_base))
+		return PTR_ERR(pp->va_cfg0_base);
+
 	pp->va_cfg1_base = pp->va_cfg0_base;
 
-	/* Index 1 is the application reg. space address */
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "app");
 	ks_pcie->va_app_base = devm_ioremap_resource(dev, res);
 	if (IS_ERR(ks_pcie->va_app_base))
 		return PTR_ERR(ks_pcie->va_app_base);
Signature · 1 line
2.17.1
#6 lore raw

PATCH v2 6/26 PCI: keystone: Move initializations to appropriate places

In reply to Kishon Vijay Abraham I

No functional change. Move host specific platform_get_resource to ks_add_pcie_port and the common platform_get_resource (applicable to both host and endpoint) to probe. This is in preparation for adding endpoint support to pci-keystone driver.

---
 drivers/pci/controller/dwc/pci-keystone.c | 27 +++++++++++++----------
 1 file changed, 15 insertions(+), 12 deletions(-)
drivers/pci/controller/dwc/pci-keystone.c +15 -12
index 5eebef9b9ada..95997885a05c 100644
@@ -806,11 +806,6 @@ static int __init ks_pcie_add_pcie_port(struct keystone_pcie *ks_pcie,
 	struct resource *res;
 	int ret;
 
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbics");
-	pci->dbi_base = devm_pci_remap_cfg_resource(dev, res);
-	if (IS_ERR(pci->dbi_base))
-		return PTR_ERR(pci->dbi_base);
-
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "config");
 	pp->va_cfg0_base = devm_pci_remap_cfg_resource(dev, res);
 	if (IS_ERR(pp->va_cfg0_base))
@@ -818,13 +813,6 @@ static int __init ks_pcie_add_pcie_port(struct keystone_pcie *ks_pcie,
 
 	pp->va_cfg1_base = pp->va_cfg0_base;
 
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "app");
-	ks_pcie->va_app_base = devm_ioremap_resource(dev, res);
-	if (IS_ERR(ks_pcie->va_app_base))
-		return PTR_ERR(ks_pcie->va_app_base);
-
-	ks_pcie->app = *res;
-
 	pp->ops = &ks_pcie_host_ops;
 	ret = dw_pcie_host_init(pp);
 	if (ret) {
@@ -895,6 +883,8 @@ static int __init ks_pcie_probe(struct platform_device *pdev)
 	struct dw_pcie *pci;
 	struct keystone_pcie *ks_pcie;
 	struct device_link **link;
+	struct resource *res;
+	void __iomem *base;
 	u32 num_viewport;
 	struct phy **phy;
 	u32 num_lanes;
@@ -911,6 +901,19 @@ static int __init ks_pcie_probe(struct platform_device *pdev)
 	if (!pci)
 		return -ENOMEM;
 
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "app");
+	ks_pcie->va_app_base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(ks_pcie->va_app_base))
+		return PTR_ERR(ks_pcie->va_app_base);
+
+	ks_pcie->app = *res;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbics");
+	base = devm_pci_remap_cfg_resource(dev, res);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	pci->dbi_base = base;
 	pci->dev = dev;
 	pci->ops = &ks_pcie_dw_pcie_ops;
 
Signature · 1 line
2.17.1
#7 lore raw

Re: [PATCH v2 06/26] PCI: keystone: Move initializations to appropriate places

Quoted 4 lines · Kishon Vijay Abraham I

No functional change. Move host specific platform_get_resource to ks_add_pcie_port and the common platform_get_resource (applicable to both host and endpoint) to probe. This is in preparation for adding endpoint support to pci-keystone driver.

This seems to move platform_get_resource() *from* (not *to*) ks_add_pcie_port().

You seem to be making a distinction in the commit log between (1) a resource that's only used for host mode, and (2) a common resource that's used for both host and endpoint mode.  But I don't see that distinction in the patch, so it's a little confusing to mention it in the commit log.

It must make endpoint support easier, but I can't quite connect the dots yet. Maybe endpoint will also use ks_pcie_add_pcie_port(), but will have a separate .probe() function that doesn't look up the resource that's specific to host mode?

Quoted 67 lines
---
 drivers/pci/controller/dwc/pci-keystone.c | 27 +++++++++++++----------
 1 file changed, 15 insertions(+), 12 deletions(-)
drivers/pci/controller/dwc/pci-keystone.c +15 -12
index 5eebef9b9ada..95997885a05c 100644
@@ -806,11 +806,6 @@ static int __init ks_pcie_add_pcie_port(struct keystone_pcie *ks_pcie,
 	struct resource *res;
 	int ret;
 
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbics");
-	pci->dbi_base = devm_pci_remap_cfg_resource(dev, res);
-	if (IS_ERR(pci->dbi_base))
-		return PTR_ERR(pci->dbi_base);
-
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "config");
 	pp->va_cfg0_base = devm_pci_remap_cfg_resource(dev, res);
 	if (IS_ERR(pp->va_cfg0_base))
@@ -818,13 +813,6 @@ static int __init ks_pcie_add_pcie_port(struct keystone_pcie *ks_pcie,
 
 	pp->va_cfg1_base = pp->va_cfg0_base;
 
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "app");
-	ks_pcie->va_app_base = devm_ioremap_resource(dev, res);
-	if (IS_ERR(ks_pcie->va_app_base))
-		return PTR_ERR(ks_pcie->va_app_base);
-
-	ks_pcie->app = *res;
-
 	pp->ops = &ks_pcie_host_ops;
 	ret = dw_pcie_host_init(pp);
 	if (ret) {
@@ -895,6 +883,8 @@ static int __init ks_pcie_probe(struct platform_device *pdev)
 	struct dw_pcie *pci;
 	struct keystone_pcie *ks_pcie;
 	struct device_link **link;
+	struct resource *res;
+	void __iomem *base;
 	u32 num_viewport;
 	struct phy **phy;
 	u32 num_lanes;
@@ -911,6 +901,19 @@ static int __init ks_pcie_probe(struct platform_device *pdev)
 	if (!pci)
 		return -ENOMEM;
 
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "app");
+	ks_pcie->va_app_base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(ks_pcie->va_app_base))
+		return PTR_ERR(ks_pcie->va_app_base);
+
+	ks_pcie->app = *res;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbics");
+	base = devm_pci_remap_cfg_resource(dev, res);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	pci->dbi_base = base;
 	pci->dev = dev;
 	pci->ops = &ks_pcie_dw_pcie_ops;
 
Signature · 1 line
2.17.1
#8 lore raw

Re: [PATCH v2 06/26] PCI: keystone: Move initializations to appropriate places

Hi Bjorn,

Quoted 8 lines · Bjorn Helgaas
Quoted 4 lines · Kishon Vijay Abraham I

No functional change. Move host specific platform_get_resource to ks_add_pcie_port and the common platform_get_resource (applicable to both host and endpoint) to probe. This is in preparation for adding endpoint support to pci-keystone driver.

This seems to move platform_get_resource() *from* (not *to*) ks_add_pcie_port().

Maybe I should have mentioned "Keep host specific platform_get_resource() in ks_add_pcie_port() and move the common platform_get_resource() (applicable to both host and endpoint) to probe()"

Quoted 11 lines

You seem to be making a distinction in the commit log between (1) a resource that's only used for host mode, and (2) a common resource that's used for both host and endpoint mode.  But I don't see that distinction in the patch, so it's a little confusing to mention it in the commit log.

It must make endpoint support easier, but I can't quite connect the dots yet. Maybe endpoint will also use ks_pcie_add_pcie_port(), but will have a separate .probe() function that doesn't look up the resource that's specific to host mode?

No ks_pcie_add_pcie_port() is specific to host mode, so "config" resource is kept there whereas "dbics" and "app" resources are common to both host mode and device mode, so they are moved to probe().

Thanks
Kishon

Quoted 65 lines
Quoted 65 lines
---
 drivers/pci/controller/dwc/pci-keystone.c | 27 +++++++++++++----------
 1 file changed, 15 insertions(+), 12 deletions(-)
drivers/pci/controller/dwc/pci-keystone.c +15 -12
index 5eebef9b9ada..95997885a05c 100644
@@ -806,11 +806,6 @@ static int __init ks_pcie_add_pcie_port(struct keystone_pcie *ks_pcie,
 	struct resource *res;
 	int ret;
 
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbics");
-	pci->dbi_base = devm_pci_remap_cfg_resource(dev, res);
-	if (IS_ERR(pci->dbi_base))
-		return PTR_ERR(pci->dbi_base);
-
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "config");
 	pp->va_cfg0_base = devm_pci_remap_cfg_resource(dev, res);
 	if (IS_ERR(pp->va_cfg0_base))
@@ -818,13 +813,6 @@ static int __init ks_pcie_add_pcie_port(struct keystone_pcie *ks_pcie,
 
 	pp->va_cfg1_base = pp->va_cfg0_base;
 
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "app");
-	ks_pcie->va_app_base = devm_ioremap_resource(dev, res);
-	if (IS_ERR(ks_pcie->va_app_base))
-		return PTR_ERR(ks_pcie->va_app_base);
-
-	ks_pcie->app = *res;
-
 	pp->ops = &ks_pcie_host_ops;
 	ret = dw_pcie_host_init(pp);
 	if (ret) {
@@ -895,6 +883,8 @@ static int __init ks_pcie_probe(struct platform_device *pdev)
 	struct dw_pcie *pci;
 	struct keystone_pcie *ks_pcie;
 	struct device_link **link;
+	struct resource *res;
+	void __iomem *base;
 	u32 num_viewport;
 	struct phy **phy;
 	u32 num_lanes;
@@ -911,6 +901,19 @@ static int __init ks_pcie_probe(struct platform_device *pdev)
 	if (!pci)
 		return -ENOMEM;
 
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "app");
+	ks_pcie->va_app_base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(ks_pcie->va_app_base))
+		return PTR_ERR(ks_pcie->va_app_base);
+
+	ks_pcie->app = *res;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbics");
+	base = devm_pci_remap_cfg_resource(dev, res);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	pci->dbi_base = base;
 	pci->dev = dev;
 	pci->ops = &ks_pcie_dw_pcie_ops;
 
Quoted 3 lines
Quoted 3 lines
Signature · 1 line
2.17.1

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#9 lore raw

Re: [PATCH v2 06/26] PCI: keystone: Move initializations to appropriate places

Quoted 9 lines · Kishon Vijay Abraham I

Hi Bjorn,

Quoted 6 lines · Bjorn Helgaas
Quoted 4 lines · Kishon Vijay Abraham I

No functional change. Move host specific platform_get_resource to ks_add_pcie_port and the common platform_get_resource (applicable to both host and endpoint) to probe. This is in preparation for adding endpoint support to pci-keystone driver.

Quoted 6 lines
Quoted 2 lines

This seems to move platform_get_resource() *from* (not *to*) ks_add_pcie_port().

Maybe I should have mentioned "Keep host specific platform_get_resource() in ks_add_pcie_port() and move the common platform_get_resource() (applicable to both host and endpoint) to probe()"

Commit log updated, pushed out pci/keystone again.

Thanks,
Lorenzo

Quoted 86 lines
Quoted 10 lines

You seem to be making a distinction in the commit log between (1) a resource that's only used for host mode, and (2) a common resource that's used for both host and endpoint mode.  But I don't see that distinction in the patch, so it's a little confusing to mention it in the commit log.

It must make endpoint support easier, but I can't quite connect the dots yet. Maybe endpoint will also use ks_pcie_add_pcie_port(), but will have a separate .probe() function that doesn't look up the resource that's specific to host mode?

No ks_pcie_add_pcie_port() is specific to host mode, so "config" resource is kept there whereas "dbics" and "app" resources are common to both host mode and device mode, so they are moved to probe().

Thanks
Kishon

Quoted 68 lines
Quoted 68 lines
---
 drivers/pci/controller/dwc/pci-keystone.c | 27 +++++++++++++----------
 1 file changed, 15 insertions(+), 12 deletions(-)
drivers/pci/controller/dwc/pci-keystone.c +15 -12
index 5eebef9b9ada..95997885a05c 100644
@@ -806,11 +806,6 @@ static int __init ks_pcie_add_pcie_port(struct keystone_pcie *ks_pcie,
 	struct resource *res;
 	int ret;
 
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbics");
-	pci->dbi_base = devm_pci_remap_cfg_resource(dev, res);
-	if (IS_ERR(pci->dbi_base))
-		return PTR_ERR(pci->dbi_base);
-
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "config");
 	pp->va_cfg0_base = devm_pci_remap_cfg_resource(dev, res);
 	if (IS_ERR(pp->va_cfg0_base))
@@ -818,13 +813,6 @@ static int __init ks_pcie_add_pcie_port(struct keystone_pcie *ks_pcie,
 
 	pp->va_cfg1_base = pp->va_cfg0_base;
 
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "app");
-	ks_pcie->va_app_base = devm_ioremap_resource(dev, res);
-	if (IS_ERR(ks_pcie->va_app_base))
-		return PTR_ERR(ks_pcie->va_app_base);
-
-	ks_pcie->app = *res;
-
 	pp->ops = &ks_pcie_host_ops;
 	ret = dw_pcie_host_init(pp);
 	if (ret) {
@@ -895,6 +883,8 @@ static int __init ks_pcie_probe(struct platform_device *pdev)
 	struct dw_pcie *pci;
 	struct keystone_pcie *ks_pcie;
 	struct device_link **link;
+	struct resource *res;
+	void __iomem *base;
 	u32 num_viewport;
 	struct phy **phy;
 	u32 num_lanes;
@@ -911,6 +901,19 @@ static int __init ks_pcie_probe(struct platform_device *pdev)
 	if (!pci)
 		return -ENOMEM;
 
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "app");
+	ks_pcie->va_app_base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(ks_pcie->va_app_base))
+		return PTR_ERR(ks_pcie->va_app_base);
+
+	ks_pcie->app = *res;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbics");
+	base = devm_pci_remap_cfg_resource(dev, res);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	pci->dbi_base = base;
 	pci->dev = dev;
 	pci->ops = &ks_pcie_dw_pcie_ops;
 
Signature · 1 line
2.17.1
#10 lore raw

PATCH v2 7/26 dt-bindings: PCI: Add dt-binding to configure PCIe mode

In reply to Kishon Vijay Abraham I

Add "ti,syscon-pcie-mode" dt-binding to hold phandle to the syscon register that should be used to configure PCIe in RC mode or EP mode.

---
 Documentation/devicetree/bindings/pci/pci-keystone.txt | 2 ++
 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/pci/pci-keystone.txt +2 -0
index 3a551687cfa2..8ee07197a063 100644
@@ -23,6 +23,8 @@ pcie_msi_intc : Interrupt controller device node for MSI IRQ chip
 
 ti,syscon-pcie-id : phandle to the device control module required to set device
 		    id and vendor id.
+ti,syscon-pcie-mode : phandle to the device control module required to configure
+		      PCI in either RC mode or EP mode.
 
  Example:
 	pcie_msi_intc: msi-interrupt-controller {
Signature · 1 line
2.17.1
#11 lore raw

PATCH v2 8/26 PCI: keystone: Explicitly set the PCIe mode

In reply to Kishon Vijay Abraham I

Explicitly set the PCIe mode to BOOTCFG_DEVCFG instead of always relying on the default values. This is required when EP mode has to be explicitly written to BOOTCFG_DEVCFG register.

---
 drivers/pci/controller/dwc/pci-keystone.c | 37 +++++++++++++++++++++++
 1 file changed, 37 insertions(+)
drivers/pci/controller/dwc/pci-keystone.c +37 -0
index 95997885a05c..dfe54553d832 100644
@@ -79,6 +79,15 @@
 #define PCIE_RC_K2L			0xb00a
 #define PCIE_RC_K2G			0xb00b
 
+#define KS_PCIE_DEV_TYPE_MASK		(0x3 << 1)
+#define KS_PCIE_DEV_TYPE(mode)		((mode) << 1)
+
+#define EP				0x0
+#define LEG_EP				0x1
+#define RC				0x2
+
+#define KS_PCIE_SYSCLOCKOUTEN		BIT(0)
+
 #define to_keystone_pcie(x)		dev_get_drvdata((x)->dev)
 
 struct keystone_pcie {
@@ -876,6 +885,30 @@ static int ks_pcie_enable_phy(struct keystone_pcie *ks_pcie)
 	return ret;
 }
 
+static int ks_pcie_set_mode(struct device *dev)
+{
+	struct device_node *np = dev->of_node;
+	struct regmap *syscon;
+	u32 val;
+	u32 mask;
+	int ret = 0;
+
+	syscon = syscon_regmap_lookup_by_phandle(np, "ti,syscon-pcie-mode");
+	if (IS_ERR(syscon))
+		return 0;
+
+	mask = KS_PCIE_DEV_TYPE_MASK | KS_PCIE_SYSCLOCKOUTEN;
+	val = KS_PCIE_DEV_TYPE(RC) | KS_PCIE_SYSCLOCKOUTEN;
+
+	ret = regmap_update_bits(syscon, 0, mask, val);
+	if (ret) {
+		dev_err(dev, "failed to set pcie mode\n");
+		return ret;
+	}
+
+	return 0;
+}
+
 static int __init ks_pcie_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -988,6 +1021,10 @@ static int __init ks_pcie_probe(struct platform_device *pdev)
 		goto err_get_sync;
 	}
 
+	ret = ks_pcie_set_mode(dev);
+	if (ret < 0)
+		goto err_get_sync;
+
 	ret = ks_pcie_add_pcie_port(ks_pcie, pdev);
 	if (ret < 0)
 		goto err_get_sync;
Signature · 1 line
2.17.1
#12 lore raw

PATCH v2 9/26 dt-bindings: PCI: Document "atu" reg-names

In reply to Kishon Vijay Abraham I

Document "atu" reg-names required to get the register space for ATU in Synopsys designware core version >= 4.80.

---
 Documentation/devicetree/bindings/pci/designware-pcie.txt | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)
Documentation/devicetree/bindings/pci/designware-pcie.txt +5 -2
index c124f9bc11f3..5561a1c060d0 100644
@@ -4,8 +4,11 @@ Required properties:
 - compatible:
 	"snps,dw-pcie" for RC mode;
 	"snps,dw-pcie-ep" for EP mode;
-- reg: Should contain the configuration address space.
-- reg-names: Must be "config" for the PCIe configuration space.
+- reg: For designware cores version < 4.80 contains the configuration
+       address space. For designware core version >= 4.80, contains
+       the configuration and ATU address space
+- reg-names: Must be "config" for the PCIe configuration space and "atu" for
+	     the ATU address space.
     (The old way of getting the configuration address space from "ranges"
     is deprecated and should be avoided.)
 - num-lanes: number of lanes to use
Signature · 1 line
2.17.1
#13 lore raw

PATCH v2 10/26 PCI: dwc: Enable iATU unroll for endpoint too

In reply to Kishon Vijay Abraham I

iatu_unroll_enabled flag is set only for Designware in host mode. However iATU unroll can be applicable for endpoint mode too. Set iatu_unroll_enabled flag in dw_pcie_setup which is common for both host mode and endpoint mode.

---
 .../pci/controller/dwc/pcie-designware-ep.c   |  4 ----
 .../pci/controller/dwc/pcie-designware-host.c | 19 -------------------
 drivers/pci/controller/dwc/pcie-designware.c  | 19 +++++++++++++++++++
 3 files changed, 19 insertions(+), 23 deletions(-)
drivers/pci/controller/dwc/pcie-designware-ep.c +0 -4
index 24f5a775ad34..dc6a4bbd3ace 100644
@@ -517,10 +517,6 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep)
 		dev_err(dev, "dbi_base/dbi_base2 is not populated\n");
 		return -EINVAL;
 	}
-	if (pci->iatu_unroll_enabled && !pci->atu_base) {
-		dev_err(dev, "atu_base is not populated\n");
-		return -EINVAL;
-	}
 
 	ret = of_property_read_u32(np, "num-ib-windows", &ep->num_ib_windows);
 	if (ret < 0) {
drivers/pci/controller/dwc/pcie-designware-host.c +0 -19
index 7e0ff7d428a9..7bf6558341b6 100644
@@ -608,17 +608,6 @@ static struct pci_ops dw_pcie_ops = {
 	.write = dw_pcie_wr_conf,
 };
 
-static u8 dw_pcie_iatu_unroll_enabled(struct dw_pcie *pci)
-{
-	u32 val;
-
-	val = dw_pcie_readl_dbi(pci, PCIE_ATU_VIEWPORT);
-	if (val == 0xffffffff)
-		return 1;
-
-	return 0;
-}
-
 void dw_pcie_setup_rc(struct pcie_port *pp)
 {
 	u32 val, ctrl, num_ctrls;
@@ -672,14 +661,6 @@ void dw_pcie_setup_rc(struct pcie_port *pp)
 	 * we should not program the ATU here.
 	 */
 	if (!pp->ops->rd_other_conf) {
-		/* Get iATU unroll support */
-		pci->iatu_unroll_enabled = dw_pcie_iatu_unroll_enabled(pci);
-		dev_dbg(pci->dev, "iATU unroll: %s\n",
-			pci->iatu_unroll_enabled ? "enabled" : "disabled");
-
-		if (pci->iatu_unroll_enabled && !pci->atu_base)
-			pci->atu_base = pci->dbi_base + DEFAULT_DBI_ATU_OFFSET;
-
 		dw_pcie_prog_outbound_atu(pci, PCIE_ATU_REGION_INDEX0,
 					  PCIE_ATU_TYPE_MEM, pp->mem_base,
 					  pp->mem_bus_addr, pp->mem_size);
drivers/pci/controller/dwc/pcie-designware.c +19 -0
index 31f6331ca46f..a14ca00f72aa 100644
@@ -339,6 +339,17 @@ int dw_pcie_link_up(struct dw_pcie *pci)
 		(!(val & PCIE_PHY_DEBUG_R1_LINK_IN_TRAINING)));
 }
 
+static u8 dw_pcie_iatu_unroll_enabled(struct dw_pcie *pci)
+{
+	u32 val;
+
+	val = dw_pcie_readl_dbi(pci, PCIE_ATU_VIEWPORT);
+	if (val == 0xffffffff)
+		return 1;
+
+	return 0;
+}
+
 void dw_pcie_setup(struct dw_pcie *pci)
 {
 	int ret;
@@ -347,6 +358,14 @@ void dw_pcie_setup(struct dw_pcie *pci)
 	struct device *dev = pci->dev;
 	struct device_node *np = dev->of_node;
 
+	/* Get iATU unroll support */
+	pci->iatu_unroll_enabled = dw_pcie_iatu_unroll_enabled(pci);
+	dev_dbg(pci->dev, "iATU unroll: %s\n",
+		pci->iatu_unroll_enabled ? "enabled" : "disabled");
+
+	if (pci->iatu_unroll_enabled && !pci->atu_base)
+		pci->atu_base = pci->dbi_base + DEFAULT_DBI_ATU_OFFSET;
+
 	ret = of_property_read_u32(np, "num-lanes", &lanes);
 	if (ret)
 		lanes = 0;
Signature · 1 line
2.17.1
#14 lore raw

PATCH v2 11/26 PCI: dwc: Fix ATU identification for designware version >= 4.80

In reply to Kishon Vijay Abraham I

Synopsys designware version >= 4.80 uses a separate register space for programming ATU. The current code identifies if there exists a separate register space by accessing the register address of ATUs in designware version < 4.80. Accessing this address results in abort in the case of K2G.

Fix it here by adding "version" member to struct dw_pcie. This should be set by platform specific drivers and designware core will use it to identify if the platform has a separate ATU space. For platforms which hasn't populated the version member, the old method of identification will still be used.

---
 drivers/pci/controller/dwc/pcie-designware.c | 14 ++++++++------
 drivers/pci/controller/dwc/pcie-designware.h |  1 +
 2 files changed, 9 insertions(+), 6 deletions(-)
drivers/pci/controller/dwc/pcie-designware.c +8 -6
index a14ca00f72aa..4e2f7946da89 100644
@@ -358,13 +358,15 @@ void dw_pcie_setup(struct dw_pcie *pci)
 	struct device *dev = pci->dev;
 	struct device_node *np = dev->of_node;
 
-	/* Get iATU unroll support */
-	pci->iatu_unroll_enabled = dw_pcie_iatu_unroll_enabled(pci);
-	dev_dbg(pci->dev, "iATU unroll: %s\n",
-		pci->iatu_unroll_enabled ? "enabled" : "disabled");
+	if (pci->version >= 0x480A || (!pci->version &&
+				       dw_pcie_iatu_unroll_enabled(pci))) {
+		pci->iatu_unroll_enabled = true;
+		if (!pci->atu_base)
+			pci->atu_base = pci->dbi_base + DEFAULT_DBI_ATU_OFFSET;
+	}
+	dev_dbg(pci->dev, "iATU unroll: %s\n", pci->iatu_unroll_enabled ?
+		"enabled" : "disabled");
 
-	if (pci->iatu_unroll_enabled && !pci->atu_base)
-		pci->atu_base = pci->dbi_base + DEFAULT_DBI_ATU_OFFSET;
 
 	ret = of_property_read_u32(np, "num-lanes", &lanes);
 	if (ret)
drivers/pci/controller/dwc/pcie-designware.h +1 -0
index ca3a3190a6f5..90a5b1215344 100644
@@ -234,6 +234,7 @@ struct dw_pcie {
 	struct pcie_port	pp;
 	struct dw_pcie_ep	ep;
 	const struct dw_pcie_ops *ops;
+	unsigned int		version;
 };
 
 #define to_dw_pcie_from_pp(port) container_of((port), struct dw_pcie, pp)
Signature · 1 line
2.17.1
#15 lore raw

PATCH v2 12/26 PCI: keystone: Prevent ARM32 specific code to be compiled for ARM64

In reply to Kishon Vijay Abraham I

hook_fault_code is an ARM32 specific API for hooking into data abort. Since pci-keystone.c will be used for AM65X platforms which is an ARM64 platform, allow hook_fault_code to be compiled only for ARM32.

---
 drivers/pci/controller/dwc/pci-keystone.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/pci/controller/dwc/pci-keystone.c +4 -0
index dfe54553d832..93296d434f40 100644
@@ -710,6 +710,7 @@ static int ks_pcie_config_legacy_irq(struct keystone_pcie *ks_pcie)
 	return ret;
 }
 
+#ifdef CONFIG_ARM
 /*
  * When a PCI device does not exist during config cycles, keystone host gets a
  * bus error instead of returning 0xffffffff. This handler always returns 0
@@ -729,6 +730,7 @@ static int ks_pcie_fault(unsigned long addr, unsigned int fsr,
 
 	return 0;
 }
+#endif
 
 static int __init ks_pcie_init_id(struct keystone_pcie *ks_pcie)
 {
@@ -778,12 +780,14 @@ static int __init ks_pcie_host_init(struct pcie_port *pp)
 	if (ret < 0)
 		return ret;
 
+#ifdef CONFIG_ARM
 	/*
 	 * PCIe access errors that result into OCP errors are caught by ARM as
 	 * "External aborts"
 	 */
 	hook_fault_code(17, ks_pcie_fault, SIGBUS, 0,
 			"Asynchronous external abort");
+#endif
 
 	ks_pcie_start_link(pci);
 	dw_pcie_wait_for_link(pci);
Signature · 1 line
2.17.1
#16 lore raw

PATCH v2 13/26 dt-bindings: PCI: Add PCI RC dt binding documentation for AM654

In reply to Kishon Vijay Abraham I

Add devicetree binding documentation for PCIe in RC mode present in AM654 SoC.

---
 Documentation/devicetree/bindings/pci/pci-keystone.txt | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/pci/pci-keystone.txt +5 -1
index 8ee07197a063..5c60e911b8b1 100644
@@ -11,7 +11,8 @@ described here as well as properties that are not applicable.
 
 Required Properties:-
 
-compatibility: "ti,keystone-pcie"
+compatibility: Should be "ti,keystone-pcie" for RC on Keystone2 SoC
+	       Should be "ti,am654-pcie-rc" for RC on AM654x SoC
 reg: Three register ranges as listed in the reg-names property
 reg-names: "dbics" for the DesignWare PCIe registers, "app" for the
 	   TI specific application registers, "config" for the
@@ -20,6 +21,9 @@ reg-names: "dbics" for the DesignWare PCIe registers, "app" for the
 pcie_msi_intc : Interrupt controller device node for MSI IRQ chip
 	interrupt-cells: should be set to 1
 	interrupts: GIC interrupt lines connected to PCI MSI interrupt lines
+	(required if the compatible is "ti,keystone-pcie")
+msi-map: As specified in Documentation/devicetree/bindings/pci/pci-msi.txt
+	 (required if the compatible is "ti,am654-pcie-rc".
 
 ti,syscon-pcie-id : phandle to the device control module required to set device
 		    id and vendor id.
Signature · 1 line
2.17.1
#17 lore raw

PATCH v2 14/26 PCI: keystone: Add support for PCIe RC in AM654x Platforms

In reply to Kishon Vijay Abraham I

Add PCIe RC support for AM654x Platforms in pci-keystone.c

---
 drivers/pci/controller/dwc/Kconfig        |   2 +-
 drivers/pci/controller/dwc/pci-keystone.c | 161 ++++++++++++++++++++--
 2 files changed, 148 insertions(+), 15 deletions(-)
drivers/pci/controller/dwc/Kconfig +1 -1
index 6ea74b1c0d94..d1d00833e0b3 100644
@@ -104,7 +104,7 @@ config PCIE_SPEAR13XX
 
 config PCI_KEYSTONE
 	bool "TI Keystone PCIe controller"
-	depends on ARCH_KEYSTONE || (ARM && COMPILE_TEST)
+	depends on ARCH_KEYSTONE || ARCH_K3 || ((ARM || ARM64) && COMPILE_TEST)
 	depends on PCI_MSI_IRQ_DOMAIN
 	select PCIE_DW_HOST
 	help
drivers/pci/controller/dwc/pci-keystone.c +147 -14

293 lines not on this page · raw message

Signature · 1 line
2.17.1
#18 lore raw

PATCH v2 15/26 PCI: keystone: Invoke phy_reset API before enabling PHY

In reply to Kishon Vijay Abraham I

SERDES connected to the PCIe controller in AM654 requires power on reset enable (POR_EN) to be set in the SERDES. The SERDES driver sets POR_EN in the reset ops and it has to be invoked before init or enable ops. In order for SERDES driver to set POR_EN, invoke phy_reset API in pci-keystone driver.

---
 drivers/pci/controller/dwc/pci-keystone.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/pci/controller/dwc/pci-keystone.c +4 -0
index a6a482bd648f..e4a816f53b8e 100644
@@ -897,6 +897,10 @@ static int ks_pcie_enable_phy(struct keystone_pcie *ks_pcie)
 	int num_lanes = ks_pcie->num_lanes;
 
 	for (i = 0; i < num_lanes; i++) {
+		ret = phy_reset(ks_pcie->phy[i]);
+		if (ret < 0)
+			goto err_phy;
+
 		ret = phy_init(ks_pcie->phy[i]);
 		if (ret < 0)
 			goto err_phy;
Signature · 1 line
2.17.1
#19 lore raw

PATCH v2 16/26 PCI: OF: Allow of_pci_get_max_link_speed() to be used by PCI Endpoint drivers

In reply to Kishon Vijay Abraham I

of_pci_get_max_link_speed() is built only if CONFIG_PCI is enabled. Make of_pci_get_max_link_speed() to be also used by PCI Endpoint controllers with just CONFIG_PCI_ENDPOINT enabled.

---
 drivers/pci/Makefile |  2 +-
 drivers/pci/of.c     | 44 +++++++++++++++++++++++---------------------
 2 files changed, 24 insertions(+), 22 deletions(-)
drivers/pci/Makefile +1 -1
index 657d642fcc67..28cdd8c0213a 100644
@@ -10,10 +10,10 @@ obj-$(CONFIG_PCI)		+= access.o bus.o probe.o host-bridge.o \
 ifdef CONFIG_PCI
 obj-$(CONFIG_PROC_FS)		+= proc.o
 obj-$(CONFIG_SYSFS)		+= slot.o
-obj-$(CONFIG_OF)		+= of.o
 obj-$(CONFIG_ACPI)		+= pci-acpi.o
 endif
 
+obj-$(CONFIG_OF)		+= of.o
 obj-$(CONFIG_PCI_QUIRKS)	+= quirks.o
 obj-$(CONFIG_PCIEPORTBUS)	+= pcie/
 obj-$(CONFIG_HOTPLUG_PCI)	+= hotplug/
drivers/pci/of.c +23 -21

59 lines not on this page · raw message

Signature · 1 line
2.17.1
#20 lore raw

PATCH v2 17/26 PCI: keystone: Add support to set the max link speed from DT

In reply to Kishon Vijay Abraham I

PCIe in TI's AM654 devices is by default configured to work in GEN3 mode. However PCIe doesn't work reliably in GEN3 mode because of SERDES configuration.

Add support to set the link speed to GEN1, GEN2 or GEN3 based on "max-link-speed" dt property with GEN2 as the default speed if "max-link-speed" is absent.

---
 drivers/pci/controller/dwc/pci-keystone.c | 35 +++++++++++++++++++++++
 1 file changed, 35 insertions(+)
drivers/pci/controller/dwc/pci-keystone.c +35 -0
index e4a816f53b8e..312fd0c49bbb 100644
@@ -28,6 +28,7 @@
 #include <linux/resource.h>
 #include <linux/signal.h>
 
+#include "../../pci.h"
 #include "pcie-designware.h"
 
 #define PCIE_VENDORID_MASK	0xffff
@@ -89,6 +90,8 @@
 #define LEG_EP				0x1
 #define RC				0x2
 
+#define EXP_CAP_ID_OFFSET		0x70
+
 #define KS_PCIE_SYSCLOCKOUTEN		BIT(0)
 
 #define AM654_PCIE_DEV_TYPE_MASK	0x3
@@ -971,6 +974,31 @@ static int ks_pcie_am654_set_mode(struct device *dev)
 	return 0;
 }
 
+static void ks_pcie_set_link_speed(struct dw_pcie *pci, int link_speed)
+{
+	u32 val;
+
+	dw_pcie_dbi_ro_wr_en(pci);
+
+	val = dw_pcie_readl_dbi(pci, EXP_CAP_ID_OFFSET + PCI_EXP_LNKCAP);
+	if ((val & PCI_EXP_LNKCAP_SLS) != link_speed) {
+		val &= ~((u32)PCI_EXP_LNKCAP_SLS);
+		val |= link_speed;
+		dw_pcie_writel_dbi(pci, EXP_CAP_ID_OFFSET + PCI_EXP_LNKCAP,
+				   val);
+	}
+
+	val = dw_pcie_readl_dbi(pci, EXP_CAP_ID_OFFSET + PCI_EXP_LNKCTL2);
+	if ((val & PCI_EXP_LNKCAP_SLS) != link_speed) {
+		val &= ~((u32)PCI_EXP_LNKCAP_SLS);
+		val |= link_speed;
+		dw_pcie_writel_dbi(pci, EXP_CAP_ID_OFFSET + PCI_EXP_LNKCTL2,
+				   val);
+	}
+
+	dw_pcie_dbi_ro_wr_dis(pci);
+}
+
 static const struct ks_pcie_of_data ks_pcie_rc_of_data = {
 	.host_ops = &ks_pcie_host_ops,
 	.version = 0x365A,
@@ -1011,6 +1039,7 @@ static int __init ks_pcie_probe(struct platform_device *pdev)
 	void __iomem *base;
 	u32 num_viewport;
 	struct phy **phy;
+	int link_speed;
 	u32 num_lanes;
 	char name[10];
 	int ret;
@@ -1165,6 +1194,12 @@ static int __init ks_pcie_probe(struct platform_device *pdev)
 		gpiod_set_value_cansleep(gpiod, 1);
 	}
 
+	link_speed = of_pci_get_max_link_speed(np);
+	if (link_speed < 0)
+		link_speed = 2;
+
+	ks_pcie_set_link_speed(pci, link_speed);
+
 	pci->pp.ops = host_ops;
 	ret = ks_pcie_add_pcie_port(ks_pcie, pdev);
 	if (ret < 0)
Signature · 1 line
2.17.1
#21 lore raw

PATCH v2 18/26 PCI: endpoint: Add support to allocate aligned buffers to be mapped in BARs

In reply to Kishon Vijay Abraham I

Modify pci_epf_alloc_space API to take alignment size as argument in order to argument in order to allocate aligned buffers to be mapped to BARs.

Add 'align' parameter to epc_features which can be used by platform drivers to specifiy the BAR allocation alignment requirements and use this while invoking pci_epf_alloc_space.

This is mainly required for Synopsys Designware PCIe core which masks the lower bits based on the BAR size (See "I/O and MEM Match Modes" section in DesignWare Cores PCI Express Controller Databook version 4.90a).

---
 drivers/pci/endpoint/functions/pci-epf-test.c |  5 +++--
 drivers/pci/endpoint/pci-epf-core.c           | 10 ++++++++--
 include/linux/pci-epc.h                       |  2 ++
 include/linux/pci-epf.h                       |  3 ++-
 4 files changed, 15 insertions(+), 5 deletions(-)
drivers/pci/endpoint/functions/pci-epf-test.c +3 -2
index d0b91da49bf4..c0786ca74312 100644
@@ -438,7 +438,7 @@ static int pci_epf_test_alloc_space(struct pci_epf *epf)
 	epc_features = epf_test->epc_features;
 
 	base = pci_epf_alloc_space(epf, sizeof(struct pci_epf_test_reg),
-				   test_reg_bar);
+				   test_reg_bar, epc_features->align);
 	if (!base) {
 		dev_err(dev, "Failed to allocated register space\n");
 		return -ENOMEM;
@@ -453,7 +453,8 @@ static int pci_epf_test_alloc_space(struct pci_epf *epf)
 		if (!!(epc_features->reserved_bar & (1 << bar)))
 			continue;
 
-		base = pci_epf_alloc_space(epf, bar_size[bar], bar);
+		base = pci_epf_alloc_space(epf, bar_size[bar], bar,
+					   epc_features->align);
 		if (!base)
 			dev_err(dev, "Failed to allocate space for BAR%d\n",
 				bar);
drivers/pci/endpoint/pci-epf-core.c +8 -2
index 8bfdcd291196..fb1306de8f40 100644
@@ -109,10 +109,12 @@ EXPORT_SYMBOL_GPL(pci_epf_free_space);
  * pci_epf_alloc_space() - allocate memory for the PCI EPF register space
  * @size: the size of the memory that has to be allocated
  * @bar: the BAR number corresponding to the allocated register space
+ * @align: alignment size for the allocation region
  *
  * Invoke to allocate memory for the PCI EPF register space.
  */
-void *pci_epf_alloc_space(struct pci_epf *epf, size_t size, enum pci_barno bar)
+void *pci_epf_alloc_space(struct pci_epf *epf, size_t size, enum pci_barno bar,
+			  size_t align)
 {
 	void *space;
 	struct device *dev = epf->epc->dev.parent;
@@ -120,7 +122,11 @@ void *pci_epf_alloc_space(struct pci_epf *epf, size_t size, enum pci_barno bar)
 
 	if (size < 128)
 		size = 128;
-	size = roundup_pow_of_two(size);
+
+	if (align)
+		size = ALIGN(size, align);
+	else
+		size = roundup_pow_of_two(size);
 
 	space = dma_alloc_coherent(dev, size, &phys_addr, GFP_KERNEL);
 	if (!space) {
include/linux/pci-epc.h +2 -0
index c3ffa3917f88..f641badc2c61 100644
@@ -109,6 +109,7 @@ struct pci_epc {
  * @reserved_bar: bitmap to indicate reserved BAR unavailable to function driver
  * @bar_fixed_64bit: bitmap to indicate fixed 64bit BARs
  * @bar_fixed_size: Array specifying the size supported by each BAR
+ * @align: alignment size required for BAR buffer allocation
  */
 struct pci_epc_features {
 	unsigned int	linkup_notifier : 1;
@@ -117,6 +118,7 @@ struct pci_epc_features {
 	u8	reserved_bar;
 	u8	bar_fixed_64bit;
 	u64	bar_fixed_size[BAR_5 + 1];
+	size_t	align;
 };
 
 #define to_pci_epc(device) container_of((device), struct pci_epc, dev)
include/linux/pci-epf.h +2 -1
index ec02f58758c8..2d6f07556682 100644
@@ -149,7 +149,8 @@ void pci_epf_destroy(struct pci_epf *epf);
 int __pci_epf_register_driver(struct pci_epf_driver *driver,
 			      struct module *owner);
 void pci_epf_unregister_driver(struct pci_epf_driver *driver);
-void *pci_epf_alloc_space(struct pci_epf *epf, size_t size, enum pci_barno bar);
+void *pci_epf_alloc_space(struct pci_epf *epf, size_t size, enum pci_barno bar,
+			  size_t align);
 void pci_epf_free_space(struct pci_epf *epf, void *addr, enum pci_barno bar);
 int pci_epf_bind(struct pci_epf *epf);
 void pci_epf_unbind(struct pci_epf *epf);
Signature · 1 line
2.17.1
#22 lore raw

PATCH v2 19/26 PCI: dwc: Add const qualifier to struct dw_pcie_ep_ops

In reply to Kishon Vijay Abraham I

Add const qualifier to struct dw_pcie_ep_ops member of struct dw_pcie_ep.

---
 drivers/pci/controller/dwc/pci-dra7xx.c           | 2 +-
 drivers/pci/controller/dwc/pcie-artpec6.c         | 2 +-
 drivers/pci/controller/dwc/pcie-designware-plat.c | 2 +-
 drivers/pci/controller/dwc/pcie-designware.h      | 2 +-
 4 files changed, 4 insertions(+), 4 deletions(-)
drivers/pci/controller/dwc/pci-dra7xx.c +1 -1
index ae84a69ae63a..b287dbf6914c 100644
@@ -406,7 +406,7 @@ dra7xx_pcie_get_features(struct dw_pcie_ep *ep)
 	return &dra7xx_pcie_epc_features;
 }
 
-static struct dw_pcie_ep_ops pcie_ep_ops = {
+static const struct dw_pcie_ep_ops pcie_ep_ops = {
 	.ep_init = dra7xx_pcie_ep_init,
 	.raise_irq = dra7xx_pcie_raise_irq,
 	.get_features = dra7xx_pcie_get_features,
drivers/pci/controller/dwc/pcie-artpec6.c +1 -1
index dba83abfe764..d00252bd8fae 100644
@@ -444,7 +444,7 @@ static int artpec6_pcie_raise_irq(struct dw_pcie_ep *ep, u8 func_no,
 	return 0;
 }
 
-static struct dw_pcie_ep_ops pcie_ep_ops = {
+static const struct dw_pcie_ep_ops pcie_ep_ops = {
 	.ep_init = artpec6_pcie_ep_init,
 	.raise_irq = artpec6_pcie_raise_irq,
 };
drivers/pci/controller/dwc/pcie-designware-plat.c +1 -1
index 932dbd0b34b6..b58fdcbc664b 100644
@@ -106,7 +106,7 @@ dw_plat_pcie_get_features(struct dw_pcie_ep *ep)
 	return &dw_plat_pcie_epc_features;
 }
 
-static struct dw_pcie_ep_ops pcie_ep_ops = {
+static const struct dw_pcie_ep_ops pcie_ep_ops = {
 	.ep_init = dw_plat_pcie_ep_init,
 	.raise_irq = dw_plat_pcie_ep_raise_irq,
 	.get_features = dw_plat_pcie_get_features,
drivers/pci/controller/dwc/pcie-designware.h +1 -1
index 90a5b1215344..e36941ff7cf6 100644
@@ -196,7 +196,7 @@ struct dw_pcie_ep_ops {
 
 struct dw_pcie_ep {
 	struct pci_epc		*epc;
-	struct dw_pcie_ep_ops	*ops;
+	const struct dw_pcie_ep_ops *ops;
 	phys_addr_t		phys_base;
 	size_t			addr_size;
 	size_t			page_size;
Signature · 1 line
2.17.1
#23 lore raw

PATCH v2 20/26 PCI: dwc: Fix dw_pcie_ep_find_capability to return correct capability offset

In reply to Kishon Vijay Abraham I

commit beb4641a787df79a ("PCI: dwc: Add MSI-X callbacks handler") while adding MSI-X callback handler, introduced dw_pcie_ep_find_capability and __dw_pcie_ep_find_next_cap for finding the MSI and MSIX capability.

However if MSI or MSIX capability is the last capability (i.e there are no additional items in the capabilities list and the Next Capability Pointer is set to '0'), __dw_pcie_ep_find_next_cap will return '0' even though MSI or MSIX capability may be present. This is because of incorrect ordering of "next_cap_ptr" check. Fix it here.

Fixes beb4641a787df79a142 ("PCI: dwc: Add MSI-X callbacks handler")
---
 drivers/pci/controller/dwc/pcie-designware-ep.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)
drivers/pci/controller/dwc/pcie-designware-ep.c +5 -5
index dc6a4bbd3ace..74477ad7467f 100644
@@ -46,16 +46,19 @@ static u8 __dw_pcie_ep_find_next_cap(struct dw_pcie *pci, u8 cap_ptr,
 	u8 cap_id, next_cap_ptr;
 	u16 reg;
 
+	if (!cap_ptr)
+		return 0;
+
 	reg = dw_pcie_readw_dbi(pci, cap_ptr);
-	next_cap_ptr = (reg & 0xff00) >> 8;
 	cap_id = (reg & 0x00ff);
 
-	if (!next_cap_ptr || cap_id > PCI_CAP_ID_MAX)
+	if (cap_id > PCI_CAP_ID_MAX)
 		return 0;
 
 	if (cap_id == cap)
 		return cap_ptr;
 
+	next_cap_ptr = (reg & 0xff00) >> 8;
 	return __dw_pcie_ep_find_next_cap(pci, next_cap_ptr, cap);
 }
 
@@ -67,9 +70,6 @@ static u8 dw_pcie_ep_find_capability(struct dw_pcie *pci, u8 cap)
 	reg = dw_pcie_readw_dbi(pci, PCI_CAPABILITY_LIST);
 	next_cap_ptr = (reg & 0x00ff);
 
-	if (!next_cap_ptr)
-		return 0;
-
 	return __dw_pcie_ep_find_next_cap(pci, next_cap_ptr, cap);
 }
 
Signature · 1 line
2.17.1
#24 lore raw

PATCH v2 21/26 PCI: dwc: Add callbacks for accessing dbi2 address space

In reply to Kishon Vijay Abraham I

Certain platforms like TI's AM654 doesn't have separate address space for dbi2 instead they are accessed using the same address space as dbi with some configuration bit set. In order to support such platforms, add callbacks for accessing dbi2 address space.

---
 drivers/pci/controller/dwc/pcie-designware.c | 31 ++++++++++++++++++++
 drivers/pci/controller/dwc/pcie-designware.h | 12 ++++++--
 2 files changed, 41 insertions(+), 2 deletions(-)
drivers/pci/controller/dwc/pcie-designware.c +31 -0
index 4e2f7946da89..d7cc1a0c1de6 100644
@@ -89,6 +89,37 @@ void __dw_pcie_write_dbi(struct dw_pcie *pci, void __iomem *base, u32 reg,
 		dev_err(pci->dev, "Write DBI address failed\n");
 }
 
+u32 __dw_pcie_read_dbi2(struct dw_pcie *pci, void __iomem *base, u32 reg,
+			size_t size)
+{
+	int ret;
+	u32 val;
+
+	if (pci->ops->read_dbi2)
+		return pci->ops->read_dbi2(pci, base, reg, size);
+
+	ret = dw_pcie_read(base + reg, size, &val);
+	if (ret)
+		dev_err(pci->dev, "read DBI address failed\n");
+
+	return val;
+}
+
+void __dw_pcie_write_dbi2(struct dw_pcie *pci, void __iomem *base, u32 reg,
+			  size_t size, u32 val)
+{
+	int ret;
+
+	if (pci->ops->write_dbi2) {
+		pci->ops->write_dbi2(pci, base, reg, size, val);
+		return;
+	}
+
+	ret = dw_pcie_write(base + reg, size, val);
+	if (ret)
+		dev_err(pci->dev, "write DBI address failed\n");
+}
+
 static u32 dw_pcie_readl_ob_unroll(struct dw_pcie *pci, u32 index, u32 reg)
 {
 	u32 offset = PCIE_GET_ATU_OUTB_UNR_REG_OFFSET(index);
drivers/pci/controller/dwc/pcie-designware.h +10 -2
index e36941ff7cf6..7abca9eb00bf 100644
@@ -218,6 +218,10 @@ struct dw_pcie_ops {
 			    size_t size);
 	void	(*write_dbi)(struct dw_pcie *pcie, void __iomem *base, u32 reg,
 			     size_t size, u32 val);
+	u32     (*read_dbi2)(struct dw_pcie *pcie, void __iomem *base, u32 reg,
+			     size_t size);
+	void    (*write_dbi2)(struct dw_pcie *pcie, void __iomem *base, u32 reg,
+			      size_t size, u32 val);
 	int	(*link_up)(struct dw_pcie *pcie);
 	int	(*start_link)(struct dw_pcie *pcie);
 	void	(*stop_link)(struct dw_pcie *pcie);
@@ -249,6 +253,10 @@ u32 __dw_pcie_read_dbi(struct dw_pcie *pci, void __iomem *base, u32 reg,
 		       size_t size);
 void __dw_pcie_write_dbi(struct dw_pcie *pci, void __iomem *base, u32 reg,
 			 size_t size, u32 val);
+u32 __dw_pcie_read_dbi2(struct dw_pcie *pci, void __iomem *base, u32 reg,
+			size_t size);
+void __dw_pcie_write_dbi2(struct dw_pcie *pci, void __iomem *base, u32 reg,
+			  size_t size, u32 val);
 int dw_pcie_link_up(struct dw_pcie *pci);
 int dw_pcie_wait_for_link(struct dw_pcie *pci);
 void dw_pcie_prog_outbound_atu(struct dw_pcie *pci, int index,
@@ -292,12 +300,12 @@ static inline u8 dw_pcie_readb_dbi(struct dw_pcie *pci, u32 reg)
 
 static inline void dw_pcie_writel_dbi2(struct dw_pcie *pci, u32 reg, u32 val)
 {
-	__dw_pcie_write_dbi(pci, pci->dbi_base2, reg, 0x4, val);
+	__dw_pcie_write_dbi2(pci, pci->dbi_base2, reg, 0x4, val);
 }
 
 static inline u32 dw_pcie_readl_dbi2(struct dw_pcie *pci, u32 reg)
 {
-	return __dw_pcie_read_dbi(pci, pci->dbi_base2, reg, 0x4);
+	return __dw_pcie_read_dbi2(pci, pci->dbi_base2, reg, 0x4);
 }
 
 static inline void dw_pcie_writel_atu(struct dw_pcie *pci, u32 reg, u32 val)
Signature · 1 line
2.17.1
#25 lore raw

PATCH v2 22/26 PCI: keystone: Add support for PCIe EP in AM654x Platforms

In reply to Kishon Vijay Abraham I

Add PCIe EP support for AM654x Platforms in pci-keystone.c

---
 drivers/pci/controller/dwc/Kconfig        |  23 +-
 drivers/pci/controller/dwc/pci-keystone.c | 242 +++++++++++++++++++---
 2 files changed, 236 insertions(+), 29 deletions(-)
drivers/pci/controller/dwc/Kconfig +21 -2
index d1d00833e0b3..b450ad2823a5 100644
@@ -105,14 +105,33 @@ config PCIE_SPEAR13XX
 config PCI_KEYSTONE
 	bool "TI Keystone PCIe controller"
 	depends on ARCH_KEYSTONE || ARCH_K3 || ((ARM || ARM64) && COMPILE_TEST)
-	depends on PCI_MSI_IRQ_DOMAIN
-	select PCIE_DW_HOST
 	help
 	  Say Y here if you want to enable PCI controller support on Keystone
 	  SoCs. The PCI controller on Keystone is based on DesignWare hardware
 	  and therefore the driver re-uses the DesignWare core functions to
 	  implement the driver.
 
+if PCI_KEYSTONE
+
+config PCI_KEYSTONE_HOST
+	bool "PCI Keystone Host Mode"
+	depends on PCI_MSI_IRQ_DOMAIN
+	select PCIE_DW_HOST
+	default y
+	help
+	 Enables support for the PCIe controller in the Keystone SoC to work in
+	 host mode.
+
+config PCI_KEYSTONE_EP
+	bool "PCI Keystone Endpoint Mode"
+	depends on PCI_ENDPOINT
+	select PCIE_DW_EP
+	help
+	 Enables support for the PCIe controller in the Keystone SoC to work in
+	 endpoint mode.
+
+endif
+
 config PCI_LAYERSCAPE
 	bool "Freescale Layerscape PCIe controller"
 	depends on OF && (ARM || ARCH_LAYERSCAPE || COMPILE_TEST)
drivers/pci/controller/dwc/pci-keystone.c +215 -27

345 lines not on this page · raw message

Signature · 1 line
2.17.1
#26 lore raw

PATCH v2 23/26 PCI: designware-ep: Configure RESBAR to advertise the smallest size

In reply to Kishon Vijay Abraham I

Configure RESBAR capability to advertise the smallest size (1MB) for couple of reasons. A) Host side resource allocation of BAR fails for larger sizes. B) Endpoint function driver does not allocate memory for all supported sizes in RESBAR capability.
If and when there is a usecase required to add more flexibility using RESBAR, this can be revisited.

---
 .../pci/controller/dwc/pcie-designware-ep.c   | 34 +++++++++++++++++++
 1 file changed, 34 insertions(+)
drivers/pci/controller/dwc/pcie-designware-ep.c +34 -0
index 74477ad7467f..0c208b9bda43 100644
@@ -504,10 +504,32 @@ void dw_pcie_ep_exit(struct dw_pcie_ep *ep)
 	pci_epc_mem_exit(epc);
 }
 
+static unsigned int dw_pcie_ep_find_ext_capability(struct dw_pcie *pci, int cap)
+{
+	u32 header;
+	int pos = PCI_CFG_SPACE_SIZE;
+
+	while (pos) {
+		header = dw_pcie_readl_dbi(pci, pos);
+		if (PCI_EXT_CAP_ID(header) == cap)
+			return pos;
+
+		pos = PCI_EXT_CAP_NEXT(header);
+		if (!pos)
+			break;
+	}
+
+	return 0;
+}
+
 int dw_pcie_ep_init(struct dw_pcie_ep *ep)
 {
+	int i;
 	int ret;
+	u32 reg;
 	void *addr;
+	unsigned int nbars;
+	unsigned int offset;
 	struct pci_epc *epc;
 	struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
 	struct device *dev = pci->dev;
@@ -591,6 +613,18 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep)
 
 	ep->msix_cap = dw_pcie_ep_find_capability(pci, PCI_CAP_ID_MSIX);
 
+	offset = dw_pcie_ep_find_ext_capability(pci, PCI_EXT_CAP_ID_REBAR);
+	if (offset) {
+		reg = dw_pcie_readl_dbi(pci, offset + PCI_REBAR_CTRL);
+		nbars = (reg & PCI_REBAR_CTRL_NBAR_MASK) >>
+			PCI_REBAR_CTRL_NBAR_SHIFT;
+
+		dw_pcie_dbi_ro_wr_en(pci);
+		for (i = 0; i < nbars; i++, offset += PCI_REBAR_CTRL)
+			dw_pcie_writel_dbi(pci, offset + PCI_REBAR_CAP, 0x0);
+		dw_pcie_dbi_ro_wr_dis(pci);
+	}
+
 	dw_pcie_setup(pci);
 
 	return 0;
Signature · 1 line
2.17.1
#27 lore raw

Re: [PATCH v2 23/26] PCI: designware-ep: Configure RESBAR to advertise the smallest size

Quoted 6 lines · Kishon Vijay Abraham I

Configure RESBAR capability to advertise the smallest size (1MB) for couple of reasons. A) Host side resource allocation of BAR fails for larger sizes. B) Endpoint function driver does not allocate memory for all supported sizes in RESBAR capability.
If and when there is a usecase required to add more flexibility using RESBAR, this can be revisited.

The #define used in the code below is "REBAR"; maybe spell it out once and then use REBAR instead of RESBAR?

Quoted 64 lines
---
 .../pci/controller/dwc/pcie-designware-ep.c   | 34 +++++++++++++++++++
 1 file changed, 34 insertions(+)
drivers/pci/controller/dwc/pcie-designware-ep.c +34 -0
index 74477ad7467f..0c208b9bda43 100644
@@ -504,10 +504,32 @@ void dw_pcie_ep_exit(struct dw_pcie_ep *ep)
 	pci_epc_mem_exit(epc);
 }
 
+static unsigned int dw_pcie_ep_find_ext_capability(struct dw_pcie *pci, int cap)
+{
+	u32 header;
+	int pos = PCI_CFG_SPACE_SIZE;
+
+	while (pos) {
+		header = dw_pcie_readl_dbi(pci, pos);
+		if (PCI_EXT_CAP_ID(header) == cap)
+			return pos;
+
+		pos = PCI_EXT_CAP_NEXT(header);
+		if (!pos)
+			break;
+	}
+
+	return 0;
+}
+
 int dw_pcie_ep_init(struct dw_pcie_ep *ep)
 {
+	int i;
 	int ret;
+	u32 reg;
 	void *addr;
+	unsigned int nbars;
+	unsigned int offset;
 	struct pci_epc *epc;
 	struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
 	struct device *dev = pci->dev;
@@ -591,6 +613,18 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep)
 
 	ep->msix_cap = dw_pcie_ep_find_capability(pci, PCI_CAP_ID_MSIX);
 
+	offset = dw_pcie_ep_find_ext_capability(pci, PCI_EXT_CAP_ID_REBAR);
+	if (offset) {
+		reg = dw_pcie_readl_dbi(pci, offset + PCI_REBAR_CTRL);
+		nbars = (reg & PCI_REBAR_CTRL_NBAR_MASK) >>
+			PCI_REBAR_CTRL_NBAR_SHIFT;
+
+		dw_pcie_dbi_ro_wr_en(pci);
+		for (i = 0; i < nbars; i++, offset += PCI_REBAR_CTRL)
+			dw_pcie_writel_dbi(pci, offset + PCI_REBAR_CAP, 0x0);
+		dw_pcie_dbi_ro_wr_dis(pci);
+	}
+
 	dw_pcie_setup(pci);
 
 	return 0;
Signature · 1 line
2.17.1
#28 lore raw

Re: [PATCH v2 23/26] PCI: designware-ep: Configure RESBAR to advertise the smallest size

Quoted 10 lines · Bjorn Helgaas
Quoted 6 lines · Kishon Vijay Abraham I

Configure RESBAR capability to advertise the smallest size (1MB) for couple of reasons. A) Host side resource allocation of BAR fails for larger sizes. B) Endpoint function driver does not allocate memory for all supported sizes in RESBAR capability.
If and when there is a usecase required to add more flexibility using RESBAR, this can be revisited.

The #define used in the code below is "REBAR"; maybe spell it out once and then use REBAR instead of RESBAR?

I think we should just name the capability as it is (Resizable BAR) the kernel defines are there already anyway. I will rewrite the log accordingly.

Lorenzo

Quoted 64 lines
Quoted 64 lines
---
 .../pci/controller/dwc/pcie-designware-ep.c   | 34 +++++++++++++++++++
 1 file changed, 34 insertions(+)
drivers/pci/controller/dwc/pcie-designware-ep.c +34 -0
index 74477ad7467f..0c208b9bda43 100644
@@ -504,10 +504,32 @@ void dw_pcie_ep_exit(struct dw_pcie_ep *ep)
 	pci_epc_mem_exit(epc);
 }
 
+static unsigned int dw_pcie_ep_find_ext_capability(struct dw_pcie *pci, int cap)
+{
+	u32 header;
+	int pos = PCI_CFG_SPACE_SIZE;
+
+	while (pos) {
+		header = dw_pcie_readl_dbi(pci, pos);
+		if (PCI_EXT_CAP_ID(header) == cap)
+			return pos;
+
+		pos = PCI_EXT_CAP_NEXT(header);
+		if (!pos)
+			break;
+	}
+
+	return 0;
+}
+
 int dw_pcie_ep_init(struct dw_pcie_ep *ep)
 {
+	int i;
 	int ret;
+	u32 reg;
 	void *addr;
+	unsigned int nbars;
+	unsigned int offset;
 	struct pci_epc *epc;
 	struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
 	struct device *dev = pci->dev;
@@ -591,6 +613,18 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep)
 
 	ep->msix_cap = dw_pcie_ep_find_capability(pci, PCI_CAP_ID_MSIX);
 
+	offset = dw_pcie_ep_find_ext_capability(pci, PCI_EXT_CAP_ID_REBAR);
+	if (offset) {
+		reg = dw_pcie_readl_dbi(pci, offset + PCI_REBAR_CTRL);
+		nbars = (reg & PCI_REBAR_CTRL_NBAR_MASK) >>
+			PCI_REBAR_CTRL_NBAR_SHIFT;
+
+		dw_pcie_dbi_ro_wr_en(pci);
+		for (i = 0; i < nbars; i++, offset += PCI_REBAR_CTRL)
+			dw_pcie_writel_dbi(pci, offset + PCI_REBAR_CAP, 0x0);
+		dw_pcie_dbi_ro_wr_dis(pci);
+	}
+
 	dw_pcie_setup(pci);
 
 	return 0;
Signature · 1 line
2.17.1
#29 lore raw

PATCH v2 24/26 PCI: designware-ep: Use aligned ATU window for raising MSI interrupts

In reply to Kishon Vijay Abraham I

Certain platforms like K2G reguires the outbound ATU window to be aligned. The alignment size is already present in mem->page_size. Use the alignment size present in mem->page_size to configre a aligned ATU window. In order to raise an interrupt, CPU has to write to address offset from the start of the window unlike before where writes were always to the beginning of the ATU window.

---
 drivers/pci/controller/dwc/pcie-designware-ep.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/pci/controller/dwc/pcie-designware-ep.c +5 -2
index 0c208b9bda43..2bf5a35c0570 100644
@@ -397,6 +397,7 @@ int dw_pcie_ep_raise_msi_irq(struct dw_pcie_ep *ep, u8 func_no,
 {
 	struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
 	struct pci_epc *epc = ep->epc;
+	unsigned int aligned_offset;
 	u16 msg_ctrl, msg_data;
 	u32 msg_addr_lower, msg_addr_upper, reg;
 	u64 msg_addr;
@@ -422,13 +423,15 @@ int dw_pcie_ep_raise_msi_irq(struct dw_pcie_ep *ep, u8 func_no,
 		reg = ep->msi_cap + PCI_MSI_DATA_32;
 		msg_data = dw_pcie_readw_dbi(pci, reg);
 	}
-	msg_addr = ((u64) msg_addr_upper) << 32 | msg_addr_lower;
+	aligned_offset = msg_addr_lower & (epc->mem->page_size - 1);
+	msg_addr = ((u64)msg_addr_upper) << 32 |
+			(msg_addr_lower & ~aligned_offset);
 	ret = dw_pcie_ep_map_addr(epc, func_no, ep->msi_mem_phys, msg_addr,
 				  epc->mem->page_size);
 	if (ret)
 		return ret;
 
-	writel(msg_data | (interrupt_num - 1), ep->msi_mem);
+	writel(msg_data | (interrupt_num - 1), ep->msi_mem + aligned_offset);
 
 	dw_pcie_ep_unmap_addr(epc, func_no, ep->msi_mem_phys);
 
Signature · 1 line
2.17.1
#30 lore raw

PATCH v2 25/26 misc: pci_endpoint_test: Add support to test PCI EP in AM654x

In reply to Kishon Vijay Abraham I

TI's AM654x PCIe EP has a restriction that BAR_0 is mapped to application registers. "PCIe Inbound Address Translation" section in AM65x Sitara Processors TRM (SPRUID7 – April 2018) describes BAR0 is reserved. Configure pci_endpoint_test to use BAR_2 instead. Also set alignment to 64K since "PCIe Subsystem Address Translation" section in TRM indicates minimum ATU window size is 64K.

---
 drivers/misc/pci_endpoint_test.c | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)
drivers/misc/pci_endpoint_test.c +17 -0
index 29582fe57151..e015e8fa9bd3 100644
@@ -75,6 +75,11 @@
 #define PCI_ENDPOINT_TEST_IRQ_TYPE		0x24
 #define PCI_ENDPOINT_TEST_IRQ_NUMBER		0x28
 
+#define PCI_DEVICE_ID_TI_AM654			0xb00c
+
+#define is_am654_pci_dev(pdev)		\
+		((pdev)->device == PCI_DEVICE_ID_TI_AM654)
+
 static DEFINE_IDA(pci_endpoint_test_ida);
 
 #define to_endpoint_test(priv) container_of((priv), struct pci_endpoint_test, \
@@ -588,6 +593,7 @@ static long pci_endpoint_test_ioctl(struct file *file, unsigned int cmd,
 	int ret = -EINVAL;
 	enum pci_barno bar;
 	struct pci_endpoint_test *test = to_endpoint_test(file->private_data);
+	struct pci_dev *pdev = test->pdev;
 
 	mutex_lock(&test->mutex);
 	switch (cmd) {
@@ -595,6 +601,8 @@ static long pci_endpoint_test_ioctl(struct file *file, unsigned int cmd,
 		bar = arg;
 		if (bar < 0 || bar > 5)
 			goto ret;
+		if (is_am654_pci_dev(pdev) && bar == BAR_0)
+			goto ret;
 		ret = pci_endpoint_test_bar(test, bar);
 		break;
 	case PCITEST_LEGACY_IRQ:
@@ -785,11 +793,20 @@ static void pci_endpoint_test_remove(struct pci_dev *pdev)
 	pci_disable_device(pdev);
 }
 
+static const struct pci_endpoint_test_data am654_data = {
+	.test_reg_bar = BAR_2,
+	.alignment = SZ_64K,
+	.irq_type = IRQ_TYPE_MSI,
+};
+
 static const struct pci_device_id pci_endpoint_test_tbl[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_DRA74x) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_DRA72x) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_FREESCALE, 0x81c0) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_SYNOPSYS, 0xedda) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_AM654),
+	  .driver_data = (kernel_ulong_t)&am654_data
+	},
 	{ }
 };
 MODULE_DEVICE_TABLE(pci, pci_endpoint_test_tbl);
Signature · 1 line
2.17.1
#31 lore raw

PATCH v2 26/26 misc: pci_endpoint_test: Fix test_reg_bar to be updated in pci_endpoint_test

In reply to Kishon Vijay Abraham I

commit 834b9051992580ac8fd3966d023b ("misc: pci_endpoint_test: Add support for PCI_ENDPOINT_TEST regs to be mapped to any BAR") while adding test_reg_bar in order to map PCI_ENDPOINT_TEST regs to be mapped to any BAR failed to update test_reg_bar in pci_endpoint_test. This results in test_reg_bar having invalid value when used outside probe. Fix it here.

Fixes 834b9051992580ac8fd3966d023b ("misc: pci_endpoint_test: Add support

for PCI_ENDPOINT_TEST regs to be mapped to any BAR")

---
 drivers/misc/pci_endpoint_test.c | 1 +
 1 file changed, 1 insertion(+)
drivers/misc/pci_endpoint_test.c +1 -0
index e015e8fa9bd3..7b015f2a1c6f 100644
@@ -670,6 +670,7 @@ static int pci_endpoint_test_probe(struct pci_dev *pdev,
 	data = (struct pci_endpoint_test_data *)ent->driver_data;
 	if (data) {
 		test_reg_bar = data->test_reg_bar;
+		test->test_reg_bar = test_reg_bar;
 		test->alignment = data->alignment;
 		irq_type = data->irq_type;
 	}
Signature · 1 line
2.17.1
#32 lore raw
In reply to Kishon Vijay Abraham I

Hi,

Quoted 19 lines · Kishon Vijay Abraham I

Add PCIe RC support for TI's AM654 SoC. The PCIe controller in AM654 uses Synopsys core revision 4.90a and uses the same TI wrapper as used in keystone2 with certain modification. Hence AM654 will use the same pci wrapper driver pci-keystone.c

This series was initially part of [1]. This series only includes patches that has to be merged via Lorenzo's tree. The PHY patches and dt patches will be sent separately.

This series is created over keystone MSI cleanup series [2].

This series:
*) Cleanup pci-keystone driver so that both RC mode and EP mode of
AM654 can be supported
*) Modify epc-core to support allocation of aligned buffers required for
AM654
*) Fix ATU unroll identification
*) Add support for both host mode and device mode in AM654

Quoted 6 lines

Changes from v1:
*) Support for legacy interrupt in AM654 is removed (see backgrond here [3]) *) Allow of_pci_get_max_link_speed to be used by Endpoint controller driver
*) Add support to set max-link-speed from DT in pci-keystone driver *) Update "Reviewed-by: Rob Herring <[email protected]>" tags.

Looks like I've missed updating the tags in the version that was sent out. I'll resend the series. Sorry for the noise.

Thanks
Kishon

Quoted 58 lines

[1] -> https://lore.kernel.org/patchwork/cover/989487/
[2] -> https://lkml.org/lkml/2019/3/21/193
[3] -> https://lkml.org/lkml/2019/3/19/235

Kishon Vijay Abraham I (26):
PCI: keystone: Add start_link/stop_link dw_pcie_ops
PCI: keystone: Cleanup error_irq configuration
dt-bindings: PCI: keystone: Add "reg-names" binding information
PCI: keystone: Perform host initialization in a single function
PCI: keystone: Use platform_get_resource_byname to get memory
resources
PCI: keystone: Move initializations to appropriate places
dt-bindings: PCI: Add dt-binding to configure PCIe mode
PCI: keystone: Explicitly set the PCIe mode
dt-bindings: PCI: Document "atu" reg-names
PCI: dwc: Enable iATU unroll for endpoint too
PCI: dwc: Fix ATU identification for designware version >= 4.80
PCI: keystone: Prevent ARM32 specific code to be compiled for ARM64
dt-bindings: PCI: Add PCI RC dt binding documentation for AM654
PCI: keystone: Add support for PCIe RC in AM654x Platforms
PCI: keystone: Invoke phy_reset API before enabling PHY
PCI: OF: Allow of_pci_get_max_link_speed() to be used by PCI Endpoint
drivers
PCI: keystone: Add support to set the max link speed from DT
PCI: endpoint: Add support to allocate aligned buffers to be mapped in
BARs
PCI: dwc: Add const qualifier to struct dw_pcie_ep_ops
PCI: dwc: Fix dw_pcie_ep_find_capability to return correct capability
offset
PCI: dwc: Add callbacks for accessing dbi2 address space
PCI: keystone: Add support for PCIe EP in AM654x Platforms
PCI: designware-ep: Configure RESBAR to advertise the smallest size
PCI: designware-ep: Use aligned ATU window for raising MSI interrupts
misc: pci_endpoint_test: Add support to test PCI EP in AM654x
misc: pci_endpoint_test: Fix test_reg_bar to be updated in
pci_endpoint_test

 .../bindings/pci/designware-pcie.txt          |   7 +-
 .../devicetree/bindings/pci/pci-keystone.txt  |  14 +-
 drivers/misc/pci_endpoint_test.c              |  18 +
 drivers/pci/Makefile                          |   2 +-
 drivers/pci/controller/dwc/Kconfig            |  25 +-
 drivers/pci/controller/dwc/pci-dra7xx.c       |   2 +-
 drivers/pci/controller/dwc/pci-keystone.c     | 577 +++++++++++++++---
 drivers/pci/controller/dwc/pcie-artpec6.c     |   2 +-
 .../pci/controller/dwc/pcie-designware-ep.c   |  55 +-
 .../pci/controller/dwc/pcie-designware-host.c |  19 -
 .../pci/controller/dwc/pcie-designware-plat.c |   2 +-
 drivers/pci/controller/dwc/pcie-designware.c  |  52 ++
 drivers/pci/controller/dwc/pcie-designware.h  |  15 +-
 drivers/pci/endpoint/functions/pci-epf-test.c |   5 +-
 drivers/pci/endpoint/pci-epf-core.c           |  10 +-
 drivers/pci/of.c                              |  44 +-
 include/linux/pci-epc.h                       |   2 +
 include/linux/pci-epf.h                       |   3 +-
 18 files changed, 682 insertions(+), 172 deletions(-)