Skip to contentSkip to conversation

ti-sysc changes to probe devices with dts data only

PATCH In review Tony Lindgren 3 participants 23 messages Mar 25, 2019 – Apr 8, 2019

Subsystems (5)
lore
Share & tools
lore

Tony Lindgren

author maintainer
#0 lore raw

cover ti-sysc changes to probe devices with dts data only

Hi all,

Here are some ti-sysc interconnect target module changes that allow dropping legacy platform data for many devices in favor of devicetree provided data.

This series depends on patch series "[PATCH 0/7] omap changes to allocate struct omap_hwmod dynamically".

I'll be posting patches separately to drop platform data. Meanwhile, the easiest way to test this series is to just temporarily comment out selected platform data entries one driver at a time. This can be done in the SoC specific struct omap_hwmod_ocp_if array at the end of the arch/arm/mach-omap2/omap_hwmod_*_data.c files.

Note that we are not yet handling all the quirks yet listed in arch/arm/mach-omap2/omap_hwmod.h in "omap_hwmod.flags definitions". We currently do not yet handle quirks for devices with:

HWMOD_NO_OCP_AUTOIDLE
HWMOD_NO_IDLEST
HWMOD_BLOCK_WFI
HWMOD_FORCE_MSTANDBY
HWMOD_RECONFIG_IO_CHAIN
HWMOD_CLKDM_NOAUTO

I'll be posting patches for these later on as needed.

Regards,

Tony

Tony Lindgren (14):
bus: ti-sysc: Fix sysc_unprepare() when no clocks have been allocated
bus: ti-sysc: Handle missed no-idle property in addition to
no-idle-on-init
bus: ti-sysc: Make functions static
bus: ti-sysc: Move legacy platform data idling into separate functions
bus: ti-sysc: Add separate functions for handling clocks
bus: ti-sysc: Enable all clocks directly during init to read revision
bus: ti-sysc: Allocate mdata as needed and do platform data based init
later
bus: ti-sysc: Manage clocks for the interconnect target module in all
cases
bus: ti-sysc: Move rstctrl reset to happen later
bus: ti-sysc: Add support for early quirks based on register address
bus: ti-sysc: Add quirk handling for external optional functional
clock
bus: ti-sysc: Pass clockactivity quirk to platform functions
bus: ti-sysc: Handle swsup idle mode quirks
bus: ti-sysc: Detect DMIC for debugging

 .../devicetree/bindings/bus/ti-sysc.txt       |   2 +
 arch/arm/mach-omap2/omap_hwmod.c              |  10 +
 drivers/bus/ti-sysc.c                         | 537 ++++++++++++++----
 include/linux/platform_data/ti-sysc.h         |   9 +-
 4 files changed, 438 insertions(+), 120 deletions(-)
Signature · 1 line
2.21.0
author maintainer
#1 lore raw

PATCH 1/14 bus: ti-sysc: Fix sysc_unprepare() when no clocks have been allocated

If we return early before ddata->clocks have been allocated we will get a NULL pointer dereference in sysc_unprepare(). Let's fix this by returning early when no clocks are allocated.

Fixes 0eecc636e5a2 ("bus: ti-sysc: Add minimal TI sysc interconnect target driver")
---
 drivers/bus/ti-sysc.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/bus/ti-sysc.c +3 -0
@@ -1331,6 +1331,9 @@ static void sysc_unprepare(struct sysc *ddata)
 {
 	int i;
 
+	if (!ddata->clocks)
+		return;
+
 	for (i = 0; i < SYSC_MAX_CLOCKS; i++) {
 		if (!IS_ERR_OR_NULL(ddata->clocks[i]))
 			clk_unprepare(ddata->clocks[i]);
Signature · 1 line
2.21.0
author maintainer
#2 lore raw

PATCH 2/14 bus: ti-sysc: Handle missed no-idle property in addition to no-idle-on-init

In reply to Tony Lindgren

We have ti,no-idle in use in addition to ti,no-idle-on-init but we're missing handling for it in the ti-sysc interconnect target module driver.

Let's also group the idle defines together and update the binding documentation for it.

---
 Documentation/devicetree/bindings/bus/ti-sysc.txt | 2 ++
 arch/arm/mach-omap2/omap_hwmod.c                  | 2 ++
 drivers/bus/ti-sysc.c                             | 5 ++++-
 include/linux/platform_data/ti-sysc.h             | 5 +++--
 4 files changed, 11 insertions(+), 3 deletions(-)
Documentation/devicetree/bindings/bus/ti-sysc.txt +2 -0
@@ -94,6 +94,8 @@ Optional properties:
 
 - ti,no-idle-on-init	interconnect target module should not be idled at init
 
+- ti,no-idle		interconnect target module should not be idled
+
 Example: Single instance of MUSB controller on omap4 using interconnect ranges
 using offsets from l4_cfg second segment (0x4a000000 + 0x80000 = 0x4a0ab000):
 
arch/arm/mach-omap2/omap_hwmod.c +2 -0
@@ -3675,6 +3675,8 @@ int omap_hwmod_init_module(struct device *dev,
 	if (error)
 		return error;
 
+	if (data->cfg->quirks & SYSC_QUIRK_NO_IDLE)
+		oh->flags |= HWMOD_NO_IDLE;
 	if (data->cfg->quirks & SYSC_QUIRK_NO_IDLE_ON_INIT)
 		oh->flags |= HWMOD_INIT_NO_IDLE;
 	if (data->cfg->quirks & SYSC_QUIRK_NO_RESET_ON_INIT)
drivers/bus/ti-sysc.c +4 -1
@@ -920,7 +920,8 @@ static int sysc_init_module(struct sysc *ddata)
 {
 	int error;
 
-	if (ddata->cfg.quirks & SYSC_QUIRK_NO_IDLE_ON_INIT) {
+	if (ddata->cfg.quirks &
+	    (SYSC_QUIRK_NO_IDLE | SYSC_QUIRK_NO_IDLE_ON_INIT)) {
 		ddata->revision = sysc_read_revision(ddata);
 		goto rev_quirks;
 	}
@@ -1281,6 +1282,8 @@ static const struct sysc_dts_quirk sysc_dts_quirks[] = {
 	  .mask = SYSC_QUIRK_NO_IDLE_ON_INIT, },
 	{ .name = "ti,no-reset-on-init",
 	  .mask = SYSC_QUIRK_NO_RESET_ON_INIT, },
+	{ .name = "ti,no-idle",
+	  .mask = SYSC_QUIRK_NO_IDLE, },
 };
 
 static void sysc_parse_dts_quirks(struct sysc *ddata, struct device_node *np,
include/linux/platform_data/ti-sysc.h +3 -2
@@ -46,8 +46,9 @@ struct sysc_regbits {
 	s8 emufree_shift;
 };
 
-#define SYSC_QUIRK_LEGACY_IDLE		BIT(8)
-#define SYSC_QUIRK_RESET_STATUS		BIT(7)
+#define SYSC_QUIRK_LEGACY_IDLE		BIT(9)
+#define SYSC_QUIRK_RESET_STATUS		BIT(8)
+#define SYSC_QUIRK_NO_IDLE		BIT(7)
 #define SYSC_QUIRK_NO_IDLE_ON_INIT	BIT(6)
 #define SYSC_QUIRK_NO_RESET_ON_INIT	BIT(5)
 #define SYSC_QUIRK_OPT_CLKS_NEEDED	BIT(4)
Signature · 1 line
2.21.0
maintainer Reviewed-by on v1 2/14
#3 lore raw

Re: [PATCH 02/14] bus: ti-sysc: Handle missed no-idle property in addition to no-idle-on-init

Quoted 9 lines · Tony Lindgren

We have ti,no-idle in use in addition to ti,no-idle-on-init but we're missing handling for it in the ti-sysc interconnect target module driver.

Let's also group the idle defines together and update the binding documentation for it.

Quoted 7 lines
---
 Documentation/devicetree/bindings/bus/ti-sysc.txt | 2 ++
 arch/arm/mach-omap2/omap_hwmod.c                  | 2 ++
 drivers/bus/ti-sysc.c                             | 5 ++++-
 include/linux/platform_data/ti-sysc.h             | 5 +++--
 4 files changed, 11 insertions(+), 3 deletions(-)
author maintainer
#4 lore raw

PATCH 3/14 bus: ti-sysc: Make functions static

In reply to Tony Lindgren

We can make sysc_write() and sysc_child_pm_domain static as noted by sparse.

---
 drivers/bus/ti-sysc.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/bus/ti-sysc.c +2 -2
@@ -94,7 +94,7 @@ struct sysc {
 static void sysc_parse_dts_quirks(struct sysc *ddata, struct device_node *np,
 				  bool is_child);
 
-void sysc_write(struct sysc *ddata, int offset, u32 value)
+static void sysc_write(struct sysc *ddata, int offset, u32 value)
 {
 	writel_relaxed(value, ddata->module_va + offset);
 }
@@ -1209,7 +1209,7 @@ static int sysc_child_resume_noirq(struct device *dev)
 }
 #endif
 
-struct dev_pm_domain sysc_child_pm_domain = {
+static struct dev_pm_domain sysc_child_pm_domain = {
 	.ops = {
 		SET_RUNTIME_PM_OPS(sysc_child_runtime_suspend,
 				   sysc_child_runtime_resume,
Signature · 1 line
2.21.0
author maintainer
#5 lore raw

PATCH 4/14 bus: ti-sysc: Move legacy platform data idling into separate functions

In reply to Tony Lindgren

Let's move the legacy idle and enable into separate functions to simplify PM runtime functions a bit.

---
 drivers/bus/ti-sysc.c | 78 +++++++++++++++++++++++++++----------------
 1 file changed, 50 insertions(+), 28 deletions(-)
drivers/bus/ti-sysc.c +50 -28
@@ -622,9 +622,50 @@ static void sysc_show_registers(struct sysc *ddata)
 		buf);
 }
 
-static int __maybe_unused sysc_runtime_suspend(struct device *dev)
+static int __maybe_unused sysc_runtime_suspend_legacy(struct device *dev,
+						      struct sysc *ddata)
+{
+	struct ti_sysc_platform_data *pdata;
+	int error;
+
+	pdata = dev_get_platdata(ddata->dev);
+	if (!pdata)
+		return 0;
+
+	if (!pdata->idle_module)
+		return -ENODEV;
+
+	error = pdata->idle_module(dev, &ddata->cookie);
+	if (error)
+		dev_err(dev, "%s: could not idle: %i\n",
+			__func__, error);
+
+	return 0;
+}
+
+static int __maybe_unused sysc_runtime_resume_legacy(struct device *dev,
+						     struct sysc *ddata)
 {
 	struct ti_sysc_platform_data *pdata;
+	int error;
+
+	pdata = dev_get_platdata(ddata->dev);
+	if (!pdata)
+		return 0;
+
+	if (!pdata->enable_module)
+		return -ENODEV;
+
+	error = pdata->enable_module(dev, &ddata->cookie);
+	if (error)
+		dev_err(dev, "%s: could not enable: %i\n",
+			__func__, error);
+
+	return 0;
+}
+
+static int __maybe_unused sysc_runtime_suspend(struct device *dev)
+{
 	struct sysc *ddata;
 	int error = 0, i;
 
@@ -634,19 +675,11 @@ static int __maybe_unused sysc_runtime_suspend(struct device *dev)
 		return 0;
 
 	if (ddata->legacy_mode) {
-		pdata = dev_get_platdata(ddata->dev);
-		if (!pdata)
-			return 0;
-
-		if (!pdata->idle_module)
-			return -ENODEV;
-
-		error = pdata->idle_module(dev, &ddata->cookie);
-		if (error)
-			dev_err(dev, "%s: could not idle: %i\n",
-				__func__, error);
+		error = sysc_runtime_suspend_legacy(dev, ddata);
+		if (!error)
+			ddata->enabled = false;
 
-		goto idled;
+		return error;
 	}
 
 	for (i = 0; i < ddata->nr_clocks; i++) {
@@ -659,7 +692,6 @@ static int __maybe_unused sysc_runtime_suspend(struct device *dev)
 		clk_disable(ddata->clocks[i]);
 	}
 
-idled:
 	ddata->enabled = false;
 
 	return error;
@@ -667,7 +699,6 @@ static int __maybe_unused sysc_runtime_suspend(struct device *dev)
 
 static int __maybe_unused sysc_runtime_resume(struct device *dev)
 {
-	struct ti_sysc_platform_data *pdata;
 	struct sysc *ddata;
 	int error = 0, i;
 
@@ -677,19 +708,11 @@ static int __maybe_unused sysc_runtime_resume(struct device *dev)
 		return 0;
 
 	if (ddata->legacy_mode) {
-		pdata = dev_get_platdata(ddata->dev);
-		if (!pdata)
-			return 0;
+		error = sysc_runtime_resume_legacy(dev, ddata);
+		if (!error)
+			ddata->enabled = true;
 
-		if (!pdata->enable_module)
-			return -ENODEV;
-
-		error = pdata->enable_module(dev, &ddata->cookie);
-		if (error)
-			dev_err(dev, "%s: could not enable: %i\n",
-				__func__, error);
-
-		goto awake;
+		return error;
 	}
 
 	for (i = 0; i < ddata->nr_clocks; i++) {
@@ -704,7 +727,6 @@ static int __maybe_unused sysc_runtime_resume(struct device *dev)
 			return error;
 	}
 
-awake:
 	ddata->enabled = true;
 
 	return error;
Signature · 1 line
2.21.0
author maintainer
#6 lore raw

PATCH 5/14 bus: ti-sysc: Add separate functions for handling clocks

In reply to Tony Lindgren

At least McPDM module depends on an external optional clock to be usable. To make handling of the McPDM clock easier in the following patches, let's add separate functions for handling the main clocks and the optional clocks.

Let's also add error handling to shut down already enabled clocks while at it.

---
 drivers/bus/ti-sysc.c | 141 ++++++++++++++++++++++++++++++++++++------
 1 file changed, 123 insertions(+), 18 deletions(-)
drivers/bus/ti-sysc.c +123 -18
@@ -231,6 +231,112 @@ static int sysc_get_clocks(struct sysc *ddata)
 	return 0;
 }
 
+static int sysc_enable_main_clocks(struct sysc *ddata)
+{
+	struct clk *clock;
+	int i, error;
+
+	if (!ddata->clocks)
+		return 0;
+
+	for (i = 0; i < SYSC_OPTFCK0; i++) {
+		clock = ddata->clocks[i];
+
+		/* Main clocks may not have ick */
+		if (IS_ERR_OR_NULL(clock))
+			continue;
+
+		error = clk_enable(clock);
+		if (error)
+			goto err_disable;
+	}
+
+	return 0;
+
+err_disable:
+	for (; i >= 0; i--) {
+		clock = ddata->clocks[i];
+
+		/* Main clocks may not have ick */
+		if (IS_ERR_OR_NULL(clock))
+			continue;
+
+		clk_disable(clock);
+	}
+
+	return error;
+}
+
+static void sysc_disable_main_clocks(struct sysc *ddata)
+{
+	struct clk *clock;
+	int i;
+
+	if (!ddata->clocks)
+		return;
+
+	for (i = 0; i < SYSC_OPTFCK0; i++) {
+		clock = ddata->clocks[i];
+		if (IS_ERR_OR_NULL(clock))
+			continue;
+
+		clk_disable(clock);
+	}
+}
+
+static int sysc_enable_opt_clocks(struct sysc *ddata)
+{
+	struct clk *clock;
+	int i, error;
+
+	if (!ddata->clocks)
+		return 0;
+
+	for (i = SYSC_OPTFCK0; i < SYSC_MAX_CLOCKS; i++) {
+		clock = ddata->clocks[i];
+
+		/* Assume no holes for opt clocks */
+		if (IS_ERR_OR_NULL(clock))
+			return 0;
+
+		error = clk_enable(clock);
+		if (error)
+			goto err_disable;
+	}
+
+	return 0;
+
+err_disable:
+	for (; i >= 0; i--) {
+		clock = ddata->clocks[i];
+		if (IS_ERR_OR_NULL(clock))
+			continue;
+
+		clk_disable(clock);
+	}
+
+	return error;
+}
+
+static void sysc_disable_opt_clocks(struct sysc *ddata)
+{
+	struct clk *clock;
+	int i;
+
+	if (!ddata->clocks)
+		return;
+
+	for (i = SYSC_OPTFCK0; i < SYSC_MAX_CLOCKS; i++) {
+		clock = ddata->clocks[i];
+
+		/* Assume no holes for opt clocks */
+		if (IS_ERR_OR_NULL(clock))
+			return;
+
+		clk_disable(clock);
+	}
+}
+
 /**
  * sysc_init_resets - reset module on init
  * @ddata: device driver data
@@ -667,7 +773,7 @@ static int __maybe_unused sysc_runtime_resume_legacy(struct device *dev,
 static int __maybe_unused sysc_runtime_suspend(struct device *dev)
 {
 	struct sysc *ddata;
-	int error = 0, i;
+	int error = 0;
 
 	ddata = dev_get_drvdata(dev);
 
@@ -682,15 +788,10 @@ static int __maybe_unused sysc_runtime_suspend(struct device *dev)
 		return error;
 	}
 
-	for (i = 0; i < ddata->nr_clocks; i++) {
-		if (IS_ERR_OR_NULL(ddata->clocks[i]))
-			continue;
+	sysc_disable_main_clocks(ddata);
 
-		if (i >= SYSC_OPTFCK0 && !sysc_opt_clks_needed(ddata))
-			break;
-
-		clk_disable(ddata->clocks[i]);
-	}
+	if (sysc_opt_clks_needed(ddata))
+		sysc_disable_opt_clocks(ddata);
 
 	ddata->enabled = false;
 
@@ -700,7 +801,7 @@ static int __maybe_unused sysc_runtime_suspend(struct device *dev)
 static int __maybe_unused sysc_runtime_resume(struct device *dev)
 {
 	struct sysc *ddata;
-	int error = 0, i;
+	int error = 0;
 
 	ddata = dev_get_drvdata(dev);
 
@@ -715,20 +816,24 @@ static int __maybe_unused sysc_runtime_resume(struct device *dev)
 		return error;
 	}
 
-	for (i = 0; i < ddata->nr_clocks; i++) {
-		if (IS_ERR_OR_NULL(ddata->clocks[i]))
-			continue;
-
-		if (i >= SYSC_OPTFCK0 && !sysc_opt_clks_needed(ddata))
-			break;
-
-		error = clk_enable(ddata->clocks[i]);
+	if (sysc_opt_clks_needed(ddata)) {
+		error = sysc_enable_opt_clocks(ddata);
 		if (error)
 			return error;
 	}
 
+	error = sysc_enable_main_clocks(ddata);
+	if (error)
+		goto err_main_clocks;
+
 	ddata->enabled = true;
 
+	return 0;
+
+err_main_clocks:
+	if (sysc_opt_clks_needed(ddata))
+		sysc_disable_opt_clocks(ddata);
+
 	return error;
 }
 
Signature · 1 line
2.21.0
author maintainer
#7 lore raw

Re: [PATCH 05/14] bus: ti-sysc: Add separate functions for handling clocks

Quoted 2 lines · Tony Lindgren

Let's also add error handling to shut down already enabled clocks while at it.

...

Quoted 5 lines
drivers/bus/ti-sysc.c +3 -0
+err_disable:
+	for (; i >= 0; i--) {
+		clock = ddata->clocks[i];

drivers/bus/ti-sysc.c

Quoted 10 lines
drivers/bus/ti-sysc.c +10 -0
+
+		/* Main clocks may not have ick */
+		if (IS_ERR_OR_NULL(clock))
+			continue;
+
+		clk_disable(clock);
+	}
+
+	return error;
+}

We need to ignore the current clock on error above and use for (i--; i >= 0; i--) instead. The same for sysc_enable_opt_clocks().

Updated patch below.

Regards,

Tony

8< --------------------

Quoted 1 line

From tony Mon Sep 17 00:00:00 2001

From: Tony Lindgren <[email protected]>
Date: Thu, 21 Mar 2019 11:00:21 -0700
Subject: [PATCH] bus: ti-sysc: Add separate functions for handling clocks

At least McPDM module depends on an external optional clock to be usable. To make handling of the McPDM clock easier in the following patches, let's add separate functions for handling the main clocks and the optional clocks.

Let's also add error handling to shut down already enabled clocks while at it.

---
 drivers/bus/ti-sysc.c | 141 ++++++++++++++++++++++++++++++++++++------
 1 file changed, 123 insertions(+), 18 deletions(-)
drivers/bus/ti-sysc.c +123 -18
@@ -231,6 +231,112 @@ static int sysc_get_clocks(struct sysc *ddata)
 	return 0;
 }
 
+static int sysc_enable_main_clocks(struct sysc *ddata)
+{
+	struct clk *clock;
+	int i, error;
+
+	if (!ddata->clocks)
+		return 0;
+
+	for (i = 0; i < SYSC_OPTFCK0; i++) {
+		clock = ddata->clocks[i];
+
+		/* Main clocks may not have ick */
+		if (IS_ERR_OR_NULL(clock))
+			continue;
+
+		error = clk_enable(clock);
+		if (error)
+			goto err_disable;
+	}
+
+	return 0;
+
+err_disable:
+	for (i--; i >= 0; i--) {
+		clock = ddata->clocks[i];
+
+		/* Main clocks may not have ick */
+		if (IS_ERR_OR_NULL(clock))
+			continue;
+
+		clk_disable(clock);
+	}
+
+	return error;
+}
+
+static void sysc_disable_main_clocks(struct sysc *ddata)
+{
+	struct clk *clock;
+	int i;
+
+	if (!ddata->clocks)
+		return;
+
+	for (i = 0; i < SYSC_OPTFCK0; i++) {
+		clock = ddata->clocks[i];
+		if (IS_ERR_OR_NULL(clock))
+			continue;
+
+		clk_disable(clock);
+	}
+}
+
+static int sysc_enable_opt_clocks(struct sysc *ddata)
+{
+	struct clk *clock;
+	int i, error;
+
+	if (!ddata->clocks)
+		return 0;
+
+	for (i = SYSC_OPTFCK0; i < SYSC_MAX_CLOCKS; i++) {
+		clock = ddata->clocks[i];
+
+		/* Assume no holes for opt clocks */
+		if (IS_ERR_OR_NULL(clock))
+			return 0;
+
+		error = clk_enable(clock);
+		if (error)
+			goto err_disable;
+	}
+
+	return 0;
+
+err_disable:
+	for (i--; i >= 0; i--) {
+		clock = ddata->clocks[i];
+		if (IS_ERR_OR_NULL(clock))
+			continue;
+
+		clk_disable(clock);
+	}
+
+	return error;
+}
+
+static void sysc_disable_opt_clocks(struct sysc *ddata)
+{
+	struct clk *clock;
+	int i;
+
+	if (!ddata->clocks)
+		return;
+
+	for (i = SYSC_OPTFCK0; i < SYSC_MAX_CLOCKS; i++) {
+		clock = ddata->clocks[i];
+
+		/* Assume no holes for opt clocks */
+		if (IS_ERR_OR_NULL(clock))
+			return;
+
+		clk_disable(clock);
+	}
+}
+
 /**
  * sysc_init_resets - reset module on init
  * @ddata: device driver data
@@ -667,7 +773,7 @@ static int __maybe_unused sysc_runtime_resume_legacy(struct device *dev,
 static int __maybe_unused sysc_runtime_suspend(struct device *dev)
 {
 	struct sysc *ddata;
-	int error = 0, i;
+	int error = 0;
 
 	ddata = dev_get_drvdata(dev);
 
@@ -682,15 +788,10 @@ static int __maybe_unused sysc_runtime_suspend(struct device *dev)
 		return error;
 	}
 
-	for (i = 0; i < ddata->nr_clocks; i++) {
-		if (IS_ERR_OR_NULL(ddata->clocks[i]))
-			continue;
+	sysc_disable_main_clocks(ddata);
 
-		if (i >= SYSC_OPTFCK0 && !sysc_opt_clks_needed(ddata))
-			break;
-
-		clk_disable(ddata->clocks[i]);
-	}
+	if (sysc_opt_clks_needed(ddata))
+		sysc_disable_opt_clocks(ddata);
 
 	ddata->enabled = false;
 
@@ -700,7 +801,7 @@ static int __maybe_unused sysc_runtime_suspend(struct device *dev)
 static int __maybe_unused sysc_runtime_resume(struct device *dev)
 {
 	struct sysc *ddata;
-	int error = 0, i;
+	int error = 0;
 
 	ddata = dev_get_drvdata(dev);
 
@@ -715,20 +816,24 @@ static int __maybe_unused sysc_runtime_resume(struct device *dev)
 		return error;
 	}
 
-	for (i = 0; i < ddata->nr_clocks; i++) {
-		if (IS_ERR_OR_NULL(ddata->clocks[i]))
-			continue;
-
-		if (i >= SYSC_OPTFCK0 && !sysc_opt_clks_needed(ddata))
-			break;
-
-		error = clk_enable(ddata->clocks[i]);
+	if (sysc_opt_clks_needed(ddata)) {
+		error = sysc_enable_opt_clocks(ddata);
 		if (error)
 			return error;
 	}
 
+	error = sysc_enable_main_clocks(ddata);
+	if (error)
+		goto err_main_clocks;
+
 	ddata->enabled = true;
 
+	return 0;
+
+err_main_clocks:
+	if (sysc_opt_clks_needed(ddata))
+		sysc_disable_opt_clocks(ddata);
+
 	return error;
 }
 
Signature · 1 line
2.21.0
author maintainer
#8 lore raw

PATCH 6/14 bus: ti-sysc: Enable all clocks directly during init to read revision

In reply to Tony Lindgren

The first thing we want to do is just read the module revision register to be able to configure the module specific quirks and configure the module registers.

As the interconnect target module may not yet be properly configured and may need a reset first, we don't want to use pm_runtime_get() at this point.

To read the revision register, let's just enable the all the clocks for the interconnect target module during init even if the optional clocks are not needed. That way we can read the revision register to configure the quirks needed for PM runtime.

---
 drivers/bus/ti-sysc.c | 50 ++++++++++++++++++++++++-------------------
 1 file changed, 28 insertions(+), 22 deletions(-)
drivers/bus/ti-sysc.c +28 -22
@@ -1042,39 +1042,45 @@ static int sysc_reset(struct sysc *ddata)
 				  100, MAX_MODULE_SOFTRESET_WAIT);
 }
 
-/* At this point the module is configured enough to read the revision */
+/*
+ * At this point the module is configured enough to read the revision but
+ * module may not be completely configured yet to use PM runtime. Enable
+ * all clocks directly during init to configure the quirks needed for PM
+ * runtime based on the revision register.
+ */
 static int sysc_init_module(struct sysc *ddata)
 {
-	int error;
+	int error = 0;
+	bool manage_clocks = true;
 
 	if (ddata->cfg.quirks &
-	    (SYSC_QUIRK_NO_IDLE | SYSC_QUIRK_NO_IDLE_ON_INIT)) {
-		ddata->revision = sysc_read_revision(ddata);
-		goto rev_quirks;
-	}
+	    (SYSC_QUIRK_NO_IDLE | SYSC_QUIRK_NO_IDLE_ON_INIT))
+		manage_clocks = false;
 
-	error = pm_runtime_get_sync(ddata->dev);
-	if (error < 0) {
-		pm_runtime_put_noidle(ddata->dev);
+	if (manage_clocks) {
+		error = sysc_enable_opt_clocks(ddata);
+		if (error)
+			return error;
 
-		return 0;
+		error = sysc_enable_main_clocks(ddata);
+		if (error)
+			goto err_opt_clocks;
 	}
 
+	ddata->revision = sysc_read_revision(ddata);
+	sysc_init_revision_quirks(ddata);
+
 	error = sysc_reset(ddata);
-	if (error) {
+	if (error)
 		dev_err(ddata->dev, "Reset failed with %d\n", error);
-		pm_runtime_put_sync(ddata->dev);
 
-		return error;
-	}
-
-	ddata->revision = sysc_read_revision(ddata);
-	pm_runtime_put_sync(ddata->dev);
-
-rev_quirks:
-	sysc_init_revision_quirks(ddata);
+	if (manage_clocks)
+		sysc_disable_main_clocks(ddata);
+err_opt_clocks:
+	if (manage_clocks)
+		sysc_disable_opt_clocks(ddata);
 
-	return 0;
+	return error;
 }
 
 static int sysc_init_sysc_mask(struct sysc *ddata)
@@ -1812,11 +1818,11 @@ static int sysc_probe(struct platform_device *pdev)
 	if (error)
 		return error;
 
-	pm_runtime_enable(ddata->dev);
 	error = sysc_init_module(ddata);
 	if (error)
 		goto unprepare;
 
+	pm_runtime_enable(ddata->dev);
 	error = pm_runtime_get_sync(ddata->dev);
 	if (error < 0) {
 		pm_runtime_put_noidle(ddata->dev);
Signature · 1 line
2.21.0
author maintainer
#9 lore raw

PATCH 7/14 bus: ti-sysc: Allocate mdata as needed and do platform data based init later

In reply to Tony Lindgren

The platform data based init functions typically reset the interconnect target module configure the registers. As we may need the interconnect target module specific quirks configured based on the revision register, we want to move the platform data based init to happen later.

Let's allocate mdata as needed so it's available for sysc_legacy_init() that we call with module clocks enabled from sysc_init_module().

---
 drivers/bus/ti-sysc.c | 54 +++++++++++++++++++++++++++++++------------
 1 file changed, 39 insertions(+), 15 deletions(-)
drivers/bus/ti-sysc.c +39 -15
@@ -75,6 +75,7 @@ struct sysc {
 	u32 module_size;
 	void __iomem *module_va;
 	int offsets[SYSC_MAX_REGS];
+	struct ti_sysc_module_data *mdata;
 	struct clk **clocks;
 	const char **clock_roles;
 	int nr_clocks;
@@ -1012,6 +1013,26 @@ static void sysc_init_revision_quirks(struct sysc *ddata)
 	}
 }
 
+/*
+ * Note that pdata->init_module() typically does a reset first. After
+ * pdata->init_module() is done, PM runtime can be used for the interconnect
+ * target module.
+ */
+static int sysc_legacy_init(struct sysc *ddata)
+{
+	struct ti_sysc_platform_data *pdata = dev_get_platdata(ddata->dev);
+	int error;
+
+	if (!ddata->legacy_mode || !pdata || !pdata->init_module)
+		return 0;
+
+	error = pdata->init_module(ddata->dev, ddata->mdata, &ddata->cookie);
+	if (error == -EEXIST)
+		error = 0;
+
+	return error;
+}
+
 static int sysc_reset(struct sysc *ddata)
 {
 	int offset = ddata->offsets[SYSC_SYSCONFIG];
@@ -1070,10 +1091,15 @@ static int sysc_init_module(struct sysc *ddata)
 	ddata->revision = sysc_read_revision(ddata);
 	sysc_init_revision_quirks(ddata);
 
+	error = sysc_legacy_init(ddata);
+	if (error)
+		goto err_main_clocks;
+
 	error = sysc_reset(ddata);
 	if (error)
 		dev_err(ddata->dev, "Reset failed with %d\n", error);
 
+err_main_clocks:
 	if (manage_clocks)
 		sysc_disable_main_clocks(ddata);
 err_opt_clocks:
@@ -1715,28 +1741,26 @@ static const struct sysc_capabilities sysc_dra7_mcan = {
 static int sysc_init_pdata(struct sysc *ddata)
 {
 	struct ti_sysc_platform_data *pdata = dev_get_platdata(ddata->dev);
-	struct ti_sysc_module_data mdata;
-	int error = 0;
+	struct ti_sysc_module_data *mdata;
 
 	if (!pdata || !ddata->legacy_mode)
 		return 0;
 
-	mdata.name = ddata->legacy_mode;
-	mdata.module_pa = ddata->module_pa;
-	mdata.module_size = ddata->module_size;
-	mdata.offsets = ddata->offsets;
-	mdata.nr_offsets = SYSC_MAX_REGS;
-	mdata.cap = ddata->cap;
-	mdata.cfg = &ddata->cfg;
+	mdata = devm_kzalloc(ddata->dev, sizeof(*mdata), GFP_KERNEL);
+	if (!mdata)
+		return -ENOMEM;
 
-	if (!pdata->init_module)
-		return -ENODEV;
+	mdata->name = ddata->legacy_mode;
+	mdata->module_pa = ddata->module_pa;
+	mdata->module_size = ddata->module_size;
+	mdata->offsets = ddata->offsets;
+	mdata->nr_offsets = SYSC_MAX_REGS;
+	mdata->cap = ddata->cap;
+	mdata->cfg = &ddata->cfg;
 
-	error = pdata->init_module(ddata->dev, &mdata, &ddata->cookie);
-	if (error == -EEXIST)
-		error = 0;
+	ddata->mdata = mdata;
 
-	return error;
+	return 0;
 }
 
 static int sysc_init_match(struct sysc *ddata)
Signature · 1 line
2.21.0
author maintainer
#10 lore raw

PATCH 8/14 bus: ti-sysc: Manage clocks for the interconnect target module in all cases

In reply to Tony Lindgren

We are currently not managing interconnect target module clocks in the for legacy platform data based case. This causes a problem for using the platform data based functions when dropping the platform data for the interconnect target module configuration.

To avoid a situation where we need to populate the main and optional clocks also for the platform data based functions, let's just manage the clocks directly in ti-sysc driver. This means that until the interconnect target module confugration platform data is dropped our use count for clk_enable() will be 2 instead of 1.

---
 drivers/bus/ti-sysc.c | 24 +++++++++++-------------
 1 file changed, 11 insertions(+), 13 deletions(-)
drivers/bus/ti-sysc.c +11 -13
@@ -783,10 +783,8 @@ static int __maybe_unused sysc_runtime_suspend(struct device *dev)
 
 	if (ddata->legacy_mode) {
 		error = sysc_runtime_suspend_legacy(dev, ddata);
-		if (!error)
-			ddata->enabled = false;
-
-		return error;
+		if (error)
+			return error;
 	}
 
 	sysc_disable_main_clocks(ddata);
@@ -809,14 +807,6 @@ static int __maybe_unused sysc_runtime_resume(struct device *dev)
 	if (ddata->enabled)
 		return 0;
 
-	if (ddata->legacy_mode) {
-		error = sysc_runtime_resume_legacy(dev, ddata);
-		if (!error)
-			ddata->enabled = true;
-
-		return error;
-	}
-
 	if (sysc_opt_clks_needed(ddata)) {
 		error = sysc_enable_opt_clocks(ddata);
 		if (error)
@@ -825,13 +815,21 @@ static int __maybe_unused sysc_runtime_resume(struct device *dev)
 
 	error = sysc_enable_main_clocks(ddata);
 	if (error)
-		goto err_main_clocks;
+		goto err_opt_clocks;
+
+	if (ddata->legacy_mode) {
+		error = sysc_runtime_resume_legacy(dev, ddata);
+		if (error)
+			goto err_main_clocks;
+	}
 
 	ddata->enabled = true;
 
 	return 0;
 
 err_main_clocks:
+	sysc_disable_main_clocks(ddata);
+err_opt_clocks:
 	if (sysc_opt_clks_needed(ddata))
 		sysc_disable_opt_clocks(ddata);
 
Signature · 1 line
2.21.0
author maintainer
#11 lore raw

PATCH 9/14 bus: ti-sysc: Move rstctrl reset to happen later

In reply to Tony Lindgren

We should not do the reset until the clocks are enabled. Let's only init restctrl in sysc_init_resets() and do the reset later on in sysc_reset().

---
 drivers/bus/ti-sysc.c | 61 ++++++++++++++++++++++++++-----------------
 1 file changed, 37 insertions(+), 24 deletions(-)
drivers/bus/ti-sysc.c +37 -24
@@ -339,38 +339,18 @@ static void sysc_disable_opt_clocks(struct sysc *ddata)
 }
 
 /**
- * sysc_init_resets - reset module on init
+ * sysc_init_resets - init rstctrl reset line if configured
  * @ddata: device driver data
  *
- * A module can have both OCP softreset control and external rstctrl.
- * If more complicated rstctrl resets are needed, please handle these
- * directly from the child device driver and map only the module reset
- * for the parent interconnect target module device.
- *
- * Automatic reset of the module on init can be skipped with the
- * "ti,no-reset-on-init" device tree property.
+ * See sysc_rstctrl_reset_deassert().
  */
 static int sysc_init_resets(struct sysc *ddata)
 {
-	int error;
-
 	ddata->rsts =
 		devm_reset_control_array_get_optional_exclusive(ddata->dev);
 	if (IS_ERR(ddata->rsts))
 		return PTR_ERR(ddata->rsts);
 
-	if (ddata->cfg.quirks & SYSC_QUIRK_NO_RESET_ON_INIT)
-		goto deassert;
-
-	error = reset_control_assert(ddata->rsts);
-	if (error)
-		return error;
-
-deassert:
-	error = reset_control_deassert(ddata->rsts);
-	if (error)
-		return error;
-
 	return 0;
 }
 
@@ -1031,14 +1011,47 @@ static int sysc_legacy_init(struct sysc *ddata)
 	return error;
 }
 
+/**
+ * sysc_rstctrl_reset_deassert - deassert rstctrl reset
+ * @ddata: device driver data
+ * @reset: reset before deassert
+ *
+ * A module can have both OCP softreset control and external rstctrl.
+ * If more complicated rstctrl resets are needed, please handle these
+ * directly from the child device driver and map only the module reset
+ * for the parent interconnect target module device.
+ *
+ * Automatic reset of the module on init can be skipped with the
+ * "ti,no-reset-on-init" device tree property.
+ */
+static int sysc_rstctrl_reset_deassert(struct sysc *ddata, bool reset)
+{
+	int error;
+
+	if (!ddata->rsts)
+		return 0;
+
+	if (reset) {
+		error = reset_control_assert(ddata->rsts);
+		if (error)
+			return error;
+	}
+
+	return reset_control_deassert(ddata->rsts);
+}
+
 static int sysc_reset(struct sysc *ddata)
 {
 	int offset = ddata->offsets[SYSC_SYSCONFIG];
-	int val;
+	int error, val;
 
 	if (ddata->legacy_mode || offset < 0 ||
 	    ddata->cfg.quirks & SYSC_QUIRK_NO_RESET_ON_INIT)
-		return 0;
+		return sysc_rstctrl_reset_deassert(ddata, false);
+
+	error = sysc_rstctrl_reset_deassert(ddata, true);
+	if (error)
+		return error;
 
 	/*
 	 * Currently only support reset status in sysstatus.
Signature · 1 line
2.21.0
author maintainer
#12 lore raw

Re: [PATCH 09/14] bus: ti-sysc: Move rstctrl reset to happen later

Quoted 2 lines · Tony Lindgren

We should not do the reset until the clocks are enabled. Let's only init restctrl in sysc_init_resets() and do the reset later on in sysc_reset().

...

Quoted 4 lines

static int sysc_reset(struct sysc *ddata)
{

(quoted diff) +0 -1
 	int offset = ddata->offsets[SYSC_SYSCONFIG];
-	int val;

Review

Quoted 10 lines
(quoted diff) +6 -1
+	int error, val;
 
 	if (ddata->legacy_mode || offset < 0 ||
 	    ddata->cfg.quirks & SYSC_QUIRK_NO_RESET_ON_INIT)
-		return 0;
+		return sysc_rstctrl_reset_deassert(ddata, false);
+
+	error = sysc_rstctrl_reset_deassert(ddata, true);
+	if (error)
+		return error;

This change is wrong, we need to deassert rstctrl reset before we enable clocks, not after. Updated version below.

Regards,

Tony

8< --------------------

Quoted 1 line

From tony Mon Sep 17 00:00:00 2001

From: Tony Lindgren <[email protected]>
Date: Thu, 21 Mar 2019 11:00:21 -0700
Subject: [PATCH] bus: ti-sysc: Move rstctrl reset to happen later

We can do the rsstctrl a bit later, but need to deassert rstctrl reset before the clocks are enabled if asserted. Let's only init restctrl in sysc_init_resets() and do the reset later on just before we enable the device clocks.

---
 drivers/bus/ti-sysc.c | 61 +++++++++++++++++++++++++++----------------
 1 file changed, 39 insertions(+), 22 deletions(-)
drivers/bus/ti-sysc.c +39 -22
@@ -339,38 +339,18 @@ static void sysc_disable_opt_clocks(struct sysc *ddata)
 }
 
 /**
- * sysc_init_resets - reset module on init
+ * sysc_init_resets - init rstctrl reset line if configured
  * @ddata: device driver data
  *
- * A module can have both OCP softreset control and external rstctrl.
- * If more complicated rstctrl resets are needed, please handle these
- * directly from the child device driver and map only the module reset
- * for the parent interconnect target module device.
- *
- * Automatic reset of the module on init can be skipped with the
- * "ti,no-reset-on-init" device tree property.
+ * See sysc_rstctrl_reset_deassert().
  */
 static int sysc_init_resets(struct sysc *ddata)
 {
-	int error;
-
 	ddata->rsts =
 		devm_reset_control_array_get_optional_exclusive(ddata->dev);
 	if (IS_ERR(ddata->rsts))
 		return PTR_ERR(ddata->rsts);
 
-	if (ddata->cfg.quirks & SYSC_QUIRK_NO_RESET_ON_INIT)
-		goto deassert;
-
-	error = reset_control_assert(ddata->rsts);
-	if (error)
-		return error;
-
-deassert:
-	error = reset_control_deassert(ddata->rsts);
-	if (error)
-		return error;
-
 	return 0;
 }
 
@@ -1031,6 +1011,35 @@ static int sysc_legacy_init(struct sysc *ddata)
 	return error;
 }
 
+/**
+ * sysc_rstctrl_reset_deassert - deassert rstctrl reset
+ * @ddata: device driver data
+ * @reset: reset before deassert
+ *
+ * A module can have both OCP softreset control and external rstctrl.
+ * If more complicated rstctrl resets are needed, please handle these
+ * directly from the child device driver and map only the module reset
+ * for the parent interconnect target module device.
+ *
+ * Automatic reset of the module on init can be skipped with the
+ * "ti,no-reset-on-init" device tree property.
+ */
+static int sysc_rstctrl_reset_deassert(struct sysc *ddata, bool reset)
+{
+	int error;
+
+	if (!ddata->rsts)
+		return 0;
+
+	if (reset) {
+		error = reset_control_assert(ddata->rsts);
+		if (error)
+			return error;
+	}
+
+	return reset_control_deassert(ddata->rsts);
+}
+
 static int sysc_reset(struct sysc *ddata)
 {
 	int offset = ddata->offsets[SYSC_SYSCONFIG];
@@ -1071,6 +1080,14 @@ static int sysc_init_module(struct sysc *ddata)
 {
 	int error = 0;
 	bool manage_clocks = true;
+	bool reset = true;
+
+	if (ddata->cfg.quirks & SYSC_QUIRK_NO_RESET_ON_INIT)
+		reset = false;
+
+	error = sysc_rstctrl_reset_deassert(ddata, reset);
+	if (error)
+		return error;
 
 	if (ddata->cfg.quirks &
 	    (SYSC_QUIRK_NO_IDLE | SYSC_QUIRK_NO_IDLE_ON_INIT))
Signature · 1 line
2.21.0
#13 lore raw

Re: [PATCH 09/14] bus: ti-sysc: Move rstctrl reset to happen later

Hi Tony,

Quoted 11 lines · Tony Lindgren
Quoted 2 lines · Tony Lindgren

We should not do the reset until the clocks are enabled. Let's only init restctrl in sysc_init_resets() and do the reset later on in sysc_reset().

...

Quoted 6 lines

static int sysc_reset(struct sysc *ddata)
{

(quoted diff) +1 -1
 	int offset = ddata->offsets[SYSC_SYSCONFIG];
-	int val;
+	int error, val;
Quoted 11 lines

Review

Quoted 8 lines
(quoted diff) +5 -1
 	if (ddata->legacy_mode || offset < 0 ||
 	    ddata->cfg.quirks & SYSC_QUIRK_NO_RESET_ON_INIT)
-		return 0;
+		return sysc_rstctrl_reset_deassert(ddata, false);
+
+	error = sysc_rstctrl_reset_deassert(ddata, true);
+	if (error)
+		return error;

This change is wrong, we need to deassert rstctrl reset before we enable clocks, not after. Updated version below.

Hmm, are you envisioning the SYSC reset (OCP SoftReset) here or the PRCM RSTCTRL hardresets here? The latter in general requires the clocks to be running first (module won't be in ready status until you deassert the hardresets with clocks running). You can look up the Warm-reset or Cold-reset sequences in the TRMs for any of the processors.

I am working on preparing the next version of PRUSS patches with ti-sysc on AM33xx/AM437x/AM57xx platforms, so will pick up these patches for my testing.

regards
Suman

Quoted 117 lines

Regards,

Tony

8< --------------------
From tony Mon Sep 17 00:00:00 2001
From: Tony Lindgren <[email protected]>
Date: Thu, 21 Mar 2019 11:00:21 -0700
Subject: [PATCH] bus: ti-sysc: Move rstctrl reset to happen later

We can do the rsstctrl a bit later, but need to deassert rstctrl reset before the clocks are enabled if asserted. Let's only init restctrl in sysc_init_resets() and do the reset later on just before we enable the device clocks.

---
 drivers/bus/ti-sysc.c | 61 +++++++++++++++++++++++++++----------------
 1 file changed, 39 insertions(+), 22 deletions(-)
drivers/bus/ti-sysc.c +39 -22
@@ -339,38 +339,18 @@ static void sysc_disable_opt_clocks(struct sysc *ddata)
 }
 
 /**
- * sysc_init_resets - reset module on init
+ * sysc_init_resets - init rstctrl reset line if configured
  * @ddata: device driver data
  *
- * A module can have both OCP softreset control and external rstctrl.
- * If more complicated rstctrl resets are needed, please handle these
- * directly from the child device driver and map only the module reset
- * for the parent interconnect target module device.
- *
- * Automatic reset of the module on init can be skipped with the
- * "ti,no-reset-on-init" device tree property.
+ * See sysc_rstctrl_reset_deassert().
  */
 static int sysc_init_resets(struct sysc *ddata)
 {
-	int error;
-
 	ddata->rsts =
 		devm_reset_control_array_get_optional_exclusive(ddata->dev);
 	if (IS_ERR(ddata->rsts))
 		return PTR_ERR(ddata->rsts);
 
-	if (ddata->cfg.quirks & SYSC_QUIRK_NO_RESET_ON_INIT)
-		goto deassert;
-
-	error = reset_control_assert(ddata->rsts);
-	if (error)
-		return error;
-
-deassert:
-	error = reset_control_deassert(ddata->rsts);
-	if (error)
-		return error;
-
 	return 0;
 }
 
@@ -1031,6 +1011,35 @@ static int sysc_legacy_init(struct sysc *ddata)
 	return error;
 }
 
+/**
+ * sysc_rstctrl_reset_deassert - deassert rstctrl reset
+ * @ddata: device driver data
+ * @reset: reset before deassert
+ *
+ * A module can have both OCP softreset control and external rstctrl.
+ * If more complicated rstctrl resets are needed, please handle these
+ * directly from the child device driver and map only the module reset
+ * for the parent interconnect target module device.
+ *
+ * Automatic reset of the module on init can be skipped with the
+ * "ti,no-reset-on-init" device tree property.
+ */
+static int sysc_rstctrl_reset_deassert(struct sysc *ddata, bool reset)
+{
+	int error;
+
+	if (!ddata->rsts)
+		return 0;
+
+	if (reset) {
+		error = reset_control_assert(ddata->rsts);
+		if (error)
+			return error;
+	}
+
+	return reset_control_deassert(ddata->rsts);
+}
+
 static int sysc_reset(struct sysc *ddata)
 {
 	int offset = ddata->offsets[SYSC_SYSCONFIG];
@@ -1071,6 +1080,14 @@ static int sysc_init_module(struct sysc *ddata)
 {
 	int error = 0;
 	bool manage_clocks = true;
+	bool reset = true;
+
+	if (ddata->cfg.quirks & SYSC_QUIRK_NO_RESET_ON_INIT)
+		reset = false;
+
+	error = sysc_rstctrl_reset_deassert(ddata, reset);
+	if (error)
+		return error;
 
 	if (ddata->cfg.quirks &
 	    (SYSC_QUIRK_NO_IDLE | SYSC_QUIRK_NO_IDLE_ON_INIT))
author maintainer
#14 lore raw

Re: [PATCH 09/14] bus: ti-sysc: Move rstctrl reset to happen later

Hi,

Quoted 6 lines · Suman Anna

On 3/26/19 6:13 PM, Tony Lindgren wrote:
Hmm, are you envisioning the SYSC reset (OCP SoftReset) here or the PRCM RSTCTRL hardresets here? The latter in general requires the clocks to be running first (module won't be in ready status until you deassert the hardresets with clocks running). You can look up the Warm-reset or Cold-reset sequences in the TRMs for any of the processors.

That's for rstctrl. I just did a quick test with my earlier reset-simple patch and I noticed sgx on am33xx produces a clock error unless we deassert it's rstrctrl before enabling clocks first:

gfx-l3-clkctrl:0004:0: failed to enable

Quoted 3 lines

I am working on preparing the next version of PRUSS patches with ti-sysc on AM33xx/AM437x/AM57xx platforms, so will pick up these patches for my testing.

OK great, yes please check and test with your rstctrl use case. I guess you still need to use the reset-simple patch for now until we have a proper prm rstctrl driver.

Note that you probably also want to leave out the struct omap_hwmod data from omap_hwmod_*_data.c files with rstctrl entries.

Regards,

Tony

#15 lore raw

Re: [PATCH 09/14] bus: ti-sysc: Move rstctrl reset to happen later

Hi Tony,

Quoted 10 lines · Tony Lindgren

Hi,

Quoted 6 lines · Suman Anna

On 3/26/19 6:13 PM, Tony Lindgren wrote:
Hmm, are you envisioning the SYSC reset (OCP SoftReset) here or the PRCM RSTCTRL hardresets here? The latter in general requires the clocks to be running first (module won't be in ready status until you deassert the hardresets with clocks running). You can look up the Warm-reset or Cold-reset sequences in the TRMs for any of the processors.

Quoted 6 lines

That's for rstctrl. I just did a quick test with my earlier reset-simple patch and I noticed sgx on am33xx produces a clock error unless we deassert it's rstrctrl before enabling clocks first:

gfx-l3-clkctrl:0004:0: failed to enable

Yeah, and I see a similar one across the other modules controlled by RSTCTRL bits for me as well - MMUs, PRUSS etc. This is because you can only check the module ready status in _omap4_clkctrl_clk_enable() only both after the clocks are turned on and resets are deasserted. That check will always fail with rstctrl asserted. The omap_hwmod code does use the reset status checks for bailing out, but that stuff is not present in clkctrl code and can only be achieved by adding a CLKF_NO_IDLEST (somewhat misnamed) to the corresponding clkctrl atm.

See [1] for AM33xx SGX. I will be posting some of these once I check the behavior.

Quoted 5 lines
Quoted 4 lines

I am working on preparing the next version of PRUSS patches with ti-sysc on AM33xx/AM437x/AM57xx platforms, so will pick up these patches for my testing.

Quoted 7 lines

OK great, yes please check and test with your rstctrl use case. I guess you still need to use the reset-simple patch for now until we have a proper prm rstctrl driver.

Note that you probably also want to leave out the struct omap_hwmod data from omap_hwmod_*_data.c files with rstctrl entries.

You mean no hwmod entries at all, or hwmod entries with no rstctrl data?

regards
Suman

[1]
http://git.ti.com/gitweb/?p=ti-linux-kernel/ti-linux-kernel.git;a=commitdiff;h=536d660714e98bdb7f96e5990a095283e52e4d8a

author maintainer
#16 lore raw

Re: [PATCH 09/14] bus: ti-sysc: Move rstctrl reset to happen later

Quoted 8 lines · Suman Anna
Quoted 6 lines · Tony Lindgren

That's for rstctrl. I just did a quick test with my earlier reset-simple patch and I noticed sgx on am33xx produces a clock error unless we deassert it's rstrctrl before enabling clocks first:

gfx-l3-clkctrl:0004:0: failed to enable

Quoted 8 lines

Yeah, and I see a similar one across the other modules controlled by RSTCTRL bits for me as well - MMUs, PRUSS etc. This is because you can only check the module ready status in _omap4_clkctrl_clk_enable() only both after the clocks are turned on and resets are deasserted. That check will always fail with rstctrl asserted. The omap_hwmod code does use the reset status checks for bailing out, but that stuff is not present in clkctrl code and can only be achieved by adding a CLKF_NO_IDLEST (somewhat misnamed) to the corresponding clkctrl atm.

Sounds like on ti-sysc init we should just deassert the rstctrl if asserted, then enable clocks, and then read the revision.

Then if we actually need to toggle rstctrl reset, that can be added with later patches. But with reset driver, the device IP handling device driver(s) should probably manage the rstctrl bits directly.

Quoted 2 lines

See [1] for AM33xx SGX. I will be posting some of these once I check the behavior.

Yeah OK sounds like we can avoid those issues by deasserting the module related rstctrl bit before enabling the clocks. Then deal with resets later if needed.

Quoted 5 lines
Quoted 3 lines

Note that you probably also want to leave out the struct omap_hwmod data from omap_hwmod_*_data.c files with rstctrl entries.

You mean no hwmod entries at all, or hwmod entries with no rstctrl data?

Except for the lack of rstctrl reset driver, struct hwmod_data entries should only be needed for the few cases where we're not yet handling some oh->flags quirks. I think most of the remaining unhandled quirks are for omap2 and 3.

Regards,

Tony

Quoted 4 lines

[1]
http://git.ti.com/gitweb/?p=ti-linux-kernel/ti-linux-kernel.git;a=commitdiff;h=536d660714e98bdb7f96e5990a095283e52e4d8a

author maintainer
#17 lore raw

PATCH 10/14 bus: ti-sysc: Add support for early quirks based on register address

In reply to Tony Lindgren

At least mcpdm needs an optional external clock enabled to function and this clock typically comes from the PMIC. We can detect mcpdm based on the interconnect target module address and set a quirk flag early.

To do this, let's initialize the clocks a bit later and add a new function for sysc_init_early_quirks(). Note that we cannot yet enable the early quirks for mcpdm until the optional external clocks are handled in the in the following patch.

---
 drivers/bus/ti-sysc.c | 46 +++++++++++++++++++++++++++++++++++++++----
 1 file changed, 42 insertions(+), 4 deletions(-)
drivers/bus/ti-sysc.c +42 -4
@@ -959,6 +959,42 @@ static const struct sysc_revision_quirk sysc_revision_quirks[] = {
 #endif
 };
 
+/*
+ * Early quirks based on module base and register offsets only that are
+ * needed before the module revision can be read
+ */
+static void sysc_init_early_quirks(struct sysc *ddata)
+{
+	const struct sysc_revision_quirk *q;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(sysc_revision_quirks); i++) {
+		q = &sysc_revision_quirks[i];
+
+		if (!q->base)
+			continue;
+
+		if (q->base != ddata->module_pa)
+			continue;
+
+		if (q->rev_offset >= 0 &&
+		    q->rev_offset != ddata->offsets[SYSC_REVISION])
+			continue;
+
+		if (q->sysc_offset >= 0 &&
+		    q->sysc_offset != ddata->offsets[SYSC_SYSCONFIG])
+			continue;
+
+		if (q->syss_offset >= 0 &&
+		    q->syss_offset != ddata->offsets[SYSC_SYSSTATUS])
+			continue;
+
+		ddata->name = q->name;
+		ddata->cfg.quirks |= q->quirks;
+	}
+}
+
+/* Quirks that also consider the revision register value */
 static void sysc_init_revision_quirks(struct sysc *ddata)
 {
 	const struct sysc_revision_quirk *q;
@@ -1825,10 +1861,6 @@ static int sysc_probe(struct platform_device *pdev)
 	if (error)
 		goto unprepare;
 
-	error = sysc_get_clocks(ddata);
-	if (error)
-		return error;
-
 	error = sysc_map_and_check_registers(ddata);
 	if (error)
 		goto unprepare;
@@ -1849,6 +1881,12 @@ static int sysc_probe(struct platform_device *pdev)
 	if (error)
 		goto unprepare;
 
+	sysc_init_early_quirks(ddata);
+
+	error = sysc_get_clocks(ddata);
+	if (error)
+		return error;
+
 	error = sysc_init_resets(ddata);
 	if (error)
 		return error;
Signature · 1 line
2.21.0
author maintainer
#18 lore raw

PATCH 11/14 bus: ti-sysc: Add quirk handling for external optional functional clock

In reply to Tony Lindgren

We cannot access mcpdm registers at all unless there is an optional pdmclk configured. As this is currently only needed for mcpdm, let's check for mcpdm in sysc_get_clocks(). If it turns out to be needed for other modules too, we can add more flags to the quirks table for this.

---
 drivers/bus/ti-sysc.c                 | 90 ++++++++++++++++++++++++++-
 include/linux/platform_data/ti-sysc.h |  1 +
 2 files changed, 90 insertions(+), 1 deletion(-)
drivers/bus/ti-sysc.c +89 -1
@@ -47,7 +47,10 @@ enum sysc_clocks {
 	SYSC_MAX_CLOCKS,
 };
 
-static const char * const clock_names[SYSC_ICK + 1] = { "fck", "ick", };
+static const char * const clock_names[SYSC_MAX_CLOCKS] = {
+	"fck", "ick", "opt0", "opt1", "opt2", "opt3", "opt4",
+	"opt5", "opt6", "opt7",
+};
 
 #define SYSC_IDLEMODE_MASK		3
 #define SYSC_CLOCKACTIVITY_MASK		3
@@ -129,6 +132,81 @@ static u32 sysc_read_revision(struct sysc *ddata)
 	return sysc_read(ddata, offset);
 }
 
+static int sysc_add_named_clock_from_child(struct sysc *ddata,
+					   const char *name,
+					   const char *optfck_name)
+{
+	struct device_node *np = ddata->dev->of_node;
+	struct device_node *child;
+	struct clk_lookup *cl;
+	struct clk *clock;
+	const char *n;
+
+	if (name)
+		n = name;
+	else
+		n = optfck_name;
+
+	/* Does the clock alias already exist? */
+	clock = of_clk_get_by_name(np, n);
+	if (!IS_ERR(clock)) {
+		clk_put(clock);
+
+		return 0;
+	}
+
+	child = of_get_next_available_child(np, NULL);
+	if (!child)
+		return -ENODEV;
+
+	clock = devm_get_clk_from_child(ddata->dev, child, name);
+	if (IS_ERR(clock))
+		return PTR_ERR(clock);
+
+	/*
+	 * Use clkdev_add() instead of clkdev_alloc() to avoid the MAX_DEV_ID
+	 * limit for clk_get(). If cl ever needs to be freed, it should be done
+	 * with clkdev_drop().
+	 */
+	cl = kcalloc(1, sizeof(*cl), GFP_KERNEL);
+	if (!cl)
+		return -ENOMEM;
+
+	cl->con_id = n;
+	cl->dev_id = dev_name(ddata->dev);
+	cl->clk = clock;
+	clkdev_add(cl);
+
+	clk_put(clock);
+
+	return 0;
+}
+
+static int sysc_init_ext_opt_clock(struct sysc *ddata, const char *name)
+{
+	const char *optfck_name;
+	int error, index;
+
+	if (ddata->nr_clocks < SYSC_OPTFCK0)
+		index = SYSC_OPTFCK0;
+	else
+		index = ddata->nr_clocks;
+
+	if (name)
+		optfck_name = name;
+	else
+		optfck_name = clock_names[index];
+
+	error = sysc_add_named_clock_from_child(ddata, name, optfck_name);
+	if (error)
+		return error;
+
+	ddata->clock_roles[index] = optfck_name;
+	ddata->nr_clocks++;
+
+	return 0;
+}
+
 static int sysc_get_one_clock(struct sysc *ddata, const char *name)
 {
 	int error, i, index = -ENODEV;
@@ -200,6 +278,12 @@ static int sysc_get_clocks(struct sysc *ddata)
 	if (ddata->nr_clocks < 1)
 		return 0;
 
+	if ((ddata->cfg.quirks & SYSC_QUIRK_EXT_OPT_CLOCK)) {
+		error = sysc_init_ext_opt_clock(ddata, NULL);
+		if (error)
+			return error;
+	}
+
 	if (ddata->nr_clocks > SYSC_MAX_CLOCKS) {
 		dev_err(ddata->dev, "too many clocks for %pOF\n", np);
 
@@ -901,6 +985,10 @@ static const struct sysc_revision_quirk sysc_revision_quirks[] = {
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x47422e03, 0xffffffff,
 		   SYSC_QUIRK_LEGACY_IDLE),
 
+	/* Quirks that need to be set based on the module address */
+	SYSC_QUIRK("mcpdm", 0x40132000, 0, 0x10, -1, 0x50000800, 0xffffffff,
+		   SYSC_QUIRK_EXT_OPT_CLOCK),
+
 #ifdef DEBUG
 	SYSC_QUIRK("adc", 0, 0, 0x10, -1, 0x47300001, 0xffffffff, 0),
 	SYSC_QUIRK("atl", 0, 0, -1, -1, 0x0a070100, 0xffffffff, 0),
include/linux/platform_data/ti-sysc.h +1 -0
@@ -46,6 +46,7 @@ struct sysc_regbits {
 	s8 emufree_shift;
 };
 
+#define SYSC_QUIRK_EXT_OPT_CLOCK	BIT(10)
 #define SYSC_QUIRK_LEGACY_IDLE		BIT(9)
 #define SYSC_QUIRK_RESET_STATUS		BIT(8)
 #define SYSC_QUIRK_NO_IDLE		BIT(7)
Signature · 1 line
2.21.0
author maintainer
#19 lore raw

Re: [PATCH 11/14] bus: ti-sysc: Add quirk handling for external optional functional clock

Review static int sysc_get_clocks(struct sysc *ddata) · line 286

Quoted 10 lines · Tony Lindgren
(quoted diff) +6 -0
@@ -200,6 +278,12 @@ static int sysc_get_clocks(struct sysc *ddata)
 	if (ddata->nr_clocks < 1)
 		return 0;
 
+	if ((ddata->cfg.quirks & SYSC_QUIRK_EXT_OPT_CLOCK)) {
+		error = sysc_init_ext_opt_clock(ddata, NULL);
+		if (error)
+			return error;
+	}
+

After some more testing with mcpdm, these flags are not enough for dropping the platform data. We need to use the same flags as in platform data, and add SYSC_QUIRK_NO_RESET_ON_INIT and SYSC_QUIRK_SWSUP_SIDLE to avoid patching this again. Updated patch below.

Regards,

Tony

8< ----------------------

Quoted 1 line

From tony Mon Sep 17 00:00:00 2001

From: Tony Lindgren <[email protected]>
Date: Thu, 21 Mar 2019 11:00:21 -0700
Subject: [PATCH] bus: ti-sysc: Add quirk handling for external optional
functional clock

We cannot access mcpdm registers at all unless there is an optional pdmclk configured. As this is currently only needed for mcpdm, let's check for mcpdm in sysc_get_clocks(). If it turns out to be needed for other modules too, we can add more flags to the quirks table for this.

---
 drivers/bus/ti-sysc.c                 | 91 ++++++++++++++++++++++++++-
 include/linux/platform_data/ti-sysc.h |  1 +
 2 files changed, 91 insertions(+), 1 deletion(-)
drivers/bus/ti-sysc.c +90 -1
@@ -47,7 +47,10 @@ enum sysc_clocks {
 	SYSC_MAX_CLOCKS,
 };
 
-static const char * const clock_names[SYSC_ICK + 1] = { "fck", "ick", };
+static const char * const clock_names[SYSC_MAX_CLOCKS] = {
+	"fck", "ick", "opt0", "opt1", "opt2", "opt3", "opt4",
+	"opt5", "opt6", "opt7",
+};
 
 #define SYSC_IDLEMODE_MASK		3
 #define SYSC_CLOCKACTIVITY_MASK		3
@@ -129,6 +132,81 @@ static u32 sysc_read_revision(struct sysc *ddata)
 	return sysc_read(ddata, offset);
 }
 
+static int sysc_add_named_clock_from_child(struct sysc *ddata,
+					   const char *name,
+					   const char *optfck_name)
+{
+	struct device_node *np = ddata->dev->of_node;
+	struct device_node *child;
+	struct clk_lookup *cl;
+	struct clk *clock;
+	const char *n;
+
+	if (name)
+		n = name;
+	else
+		n = optfck_name;
+
+	/* Does the clock alias already exist? */
+	clock = of_clk_get_by_name(np, n);
+	if (!IS_ERR(clock)) {
+		clk_put(clock);
+
+		return 0;
+	}
+
+	child = of_get_next_available_child(np, NULL);
+	if (!child)
+		return -ENODEV;
+
+	clock = devm_get_clk_from_child(ddata->dev, child, name);
+	if (IS_ERR(clock))
+		return PTR_ERR(clock);
+
+	/*
+	 * Use clkdev_add() instead of clkdev_alloc() to avoid the MAX_DEV_ID
+	 * limit for clk_get(). If cl ever needs to be freed, it should be done
+	 * with clkdev_drop().
+	 */
+	cl = kcalloc(1, sizeof(*cl), GFP_KERNEL);
+	if (!cl)
+		return -ENOMEM;
+
+	cl->con_id = n;
+	cl->dev_id = dev_name(ddata->dev);
+	cl->clk = clock;
+	clkdev_add(cl);
+
+	clk_put(clock);
+
+	return 0;
+}
+
+static int sysc_init_ext_opt_clock(struct sysc *ddata, const char *name)
+{
+	const char *optfck_name;
+	int error, index;
+
+	if (ddata->nr_clocks < SYSC_OPTFCK0)
+		index = SYSC_OPTFCK0;
+	else
+		index = ddata->nr_clocks;
+
+	if (name)
+		optfck_name = name;
+	else
+		optfck_name = clock_names[index];
+
+	error = sysc_add_named_clock_from_child(ddata, name, optfck_name);
+	if (error)
+		return error;
+
+	ddata->clock_roles[index] = optfck_name;
+	ddata->nr_clocks++;
+
+	return 0;
+}
+
 static int sysc_get_one_clock(struct sysc *ddata, const char *name)
 {
 	int error, i, index = -ENODEV;
@@ -200,6 +278,12 @@ static int sysc_get_clocks(struct sysc *ddata)
 	if (ddata->nr_clocks < 1)
 		return 0;
 
+	if ((ddata->cfg.quirks & SYSC_QUIRK_EXT_OPT_CLOCK)) {
+		error = sysc_init_ext_opt_clock(ddata, NULL);
+		if (error)
+			return error;
+	}
+
 	if (ddata->nr_clocks > SYSC_MAX_CLOCKS) {
 		dev_err(ddata->dev, "too many clocks for %pOF\n", np);
 
@@ -901,6 +985,11 @@ static const struct sysc_revision_quirk sysc_revision_quirks[] = {
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x47422e03, 0xffffffff,
 		   SYSC_QUIRK_LEGACY_IDLE),
 
+	/* Quirks that need to be set based on the module address */
+	SYSC_QUIRK("mcpdm", 0x40132000, 0, 0x10, -1, 0x50000800, 0xffffffff,
+		   SYSC_QUIRK_EXT_OPT_CLOCK | SYSC_QUIRK_NO_RESET_ON_INIT |
+		   SYSC_QUIRK_SWSUP_SIDLE),
+
 #ifdef DEBUG
 	SYSC_QUIRK("adc", 0, 0, 0x10, -1, 0x47300001, 0xffffffff, 0),
 	SYSC_QUIRK("atl", 0, 0, -1, -1, 0x0a070100, 0xffffffff, 0),
include/linux/platform_data/ti-sysc.h +1 -0
@@ -46,6 +46,7 @@ struct sysc_regbits {
 	s8 emufree_shift;
 };
 
+#define SYSC_QUIRK_EXT_OPT_CLOCK	BIT(10)
 #define SYSC_QUIRK_LEGACY_IDLE		BIT(9)
 #define SYSC_QUIRK_RESET_STATUS		BIT(8)
 #define SYSC_QUIRK_NO_IDLE		BIT(7)
Signature · 1 line
2.21.0
author maintainer
#20 lore raw

PATCH 12/14 bus: ti-sysc: Pass clockactivity quirk to platform functions

In reply to Tony Lindgren

We already have the clockactivity quirk set for some modules like i2c, timers and smartreflex. But we're not passing it to the platform functions yet. Let's start doing that in preparation of dropping interconnect target module platform data in favor of device tree based data.

---
 arch/arm/mach-omap2/omap_hwmod.c | 2 ++
 1 file changed, 2 insertions(+)
arch/arm/mach-omap2/omap_hwmod.c +2 -0
@@ -3681,6 +3681,8 @@ int omap_hwmod_init_module(struct device *dev,
 		oh->flags |= HWMOD_INIT_NO_IDLE;
 	if (data->cfg->quirks & SYSC_QUIRK_NO_RESET_ON_INIT)
 		oh->flags |= HWMOD_INIT_NO_RESET;
+	if (data->cfg->quirks & SYSC_QUIRK_USE_CLOCKACT)
+		oh->flags |= HWMOD_SET_DEFAULT_CLOCKACT;
 
 	error = omap_hwmod_check_module(dev, oh, data, sysc_fields,
 					rev_offs, sysc_offs, syss_offs,
Signature · 1 line
2.21.0
author maintainer
#21 lore raw

PATCH 13/14 bus: ti-sysc: Handle swsup idle mode quirks

In reply to Tony Lindgren

In preparation of dropping interconnect target module platform data in favor of devicetree based data, we must pass swsup idle quirks to the platform data functions.

For now, let's only tag the UART modules with the SWSUP_SIDLE_ACT quirk. The other modules will get tagged with swsup quirks as we drop the platform data and test the changes.

---
 arch/arm/mach-omap2/omap_hwmod.c      | 6 ++++++
 drivers/bus/ti-sysc.c                 | 6 +++---
 include/linux/platform_data/ti-sysc.h | 3 +++
 3 files changed, 12 insertions(+), 3 deletions(-)
arch/arm/mach-omap2/omap_hwmod.c +6 -0
@@ -3683,6 +3683,12 @@ int omap_hwmod_init_module(struct device *dev,
 		oh->flags |= HWMOD_INIT_NO_RESET;
 	if (data->cfg->quirks & SYSC_QUIRK_USE_CLOCKACT)
 		oh->flags |= HWMOD_SET_DEFAULT_CLOCKACT;
+	if (data->cfg->quirks & SYSC_QUIRK_SWSUP_SIDLE)
+		oh->flags |= HWMOD_SWSUP_SIDLE;
+	if (data->cfg->quirks & SYSC_QUIRK_SWSUP_SIDLE_ACT)
+		oh->flags |= HWMOD_SWSUP_SIDLE_ACT;
+	if (data->cfg->quirks & SYSC_QUIRK_SWSUP_MSTANDBY)
+		oh->flags |= HWMOD_SWSUP_MSTANDBY;
 
 	error = omap_hwmod_check_module(dev, oh, data, sysc_fields,
 					rev_offs, sysc_offs, syss_offs,
drivers/bus/ti-sysc.c +3 -3
@@ -978,12 +978,12 @@ static const struct sysc_revision_quirk sysc_revision_quirks[] = {
 	SYSC_QUIRK("timer", 0, 0, 0x10, -1, 0x4fff1301, 0xffff00ff,
 		   0),
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x00000052, 0xffffffff,
-		   SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 	/* Uarts on omap4 and later */
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x50411e03, 0xffff00ff,
-		   SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x47422e03, 0xffffffff,
-		   SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 
 	/* Quirks that need to be set based on the module address */
 	SYSC_QUIRK("mcpdm", 0x40132000, 0, 0x10, -1, 0x50000800, 0xffffffff,
include/linux/platform_data/ti-sysc.h +3 -0
@@ -46,6 +46,9 @@ struct sysc_regbits {
 	s8 emufree_shift;
 };
 
+#define SYSC_QUIRK_SWSUP_MSTANDBY	BIT(13)
+#define SYSC_QUIRK_SWSUP_SIDLE_ACT	BIT(12)
+#define SYSC_QUIRK_SWSUP_SIDLE		BIT(11)
 #define SYSC_QUIRK_EXT_OPT_CLOCK	BIT(10)
 #define SYSC_QUIRK_LEGACY_IDLE		BIT(9)
 #define SYSC_QUIRK_RESET_STATUS		BIT(8)
Signature · 1 line
2.21.0
author maintainer
#22 lore raw

PATCH 14/14 bus: ti-sysc: Detect DMIC for debugging

In reply to Tony Lindgren

Detect DMIC to see what we have connected if config DEBUG is enabled.

---
 drivers/bus/ti-sysc.c | 1 +
 1 file changed, 1 insertion(+)
drivers/bus/ti-sysc.c +1 -0
@@ -999,6 +999,7 @@ static const struct sysc_revision_quirk sysc_revision_quirks[] = {
 		   0xffff00f0, 0),
 	SYSC_QUIRK("dcan", 0, 0, -1, -1, 0xffffffff, 0xffffffff, 0),
 	SYSC_QUIRK("dcan", 0, 0, -1, -1, 0x00001401, 0xffffffff, 0),
+	SYSC_QUIRK("dmic", 0, 0, 0x10, -1, 0x50010000, 0xffffffff, 0),
 	SYSC_QUIRK("dwc3", 0, 0, 0x10, -1, 0x500a0200, 0xffffffff, 0),
 	SYSC_QUIRK("epwmss", 0, 0, 0x4, -1, 0x47400001, 0xffffffff, 0),
 	SYSC_QUIRK("gpu", 0, 0x1fc00, 0x1fc10, -1, 0, 0, 0),
Signature · 1 line
2.21.0