dt-bindings: vendor-prefixes: add AZW
Subsystems (2)
PATCH 1/2 dt-bindings: vendor-prefixes: add AZW
Shenzhen AZW Technology Co. Ltd. is a manufacturer specialized in Android smart TV boxes, Intel mini PCs and home cloud TV boxes with NAS.
Add the vendor prefix for AZW.
--- Documentation/devicetree/bindings/vendor-prefixes.txt | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/vendor-prefixes.txt +1 -0
@@ -54,6 +54,7 @@ avic Shanghai AVIC Optoelectronics Co., Ltd. avnet Avnet, Inc. axentia Axentia Technologies AB axis Axis Communications AB +azw Shenzhen AZW Technology Co., Ltd. bananapi BIPAI KEJI LIMITED bhf Beckhoff Automation GmbH & Co. KG bitmain Bitmain Technologies
Signature · 1 line
2.17.1
PATCH 2/2 ARM: dts: sun50i: h6: Introduce Beelink GS1 board
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- FN-Link 6222B-SRB Wifi/BT
- 1x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- S/PDIF Tx
- IR receiver
- 5V/2A DC power supply
---
Thanks to Jagan and Icenowy, most of this devicetree is taken from their works on the OrangePi One Plus and Pine H64.
arch/arm64/boot/dts/allwinner/Makefile | 1 + .../dts/allwinner/sun50i-h6-beelink-gs1.dts | 252 ++++++++++++++++++ 2 files changed, 253 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
arch/arm64/boot/dts/allwinner/Makefile +1 -0
@@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-beelink-gs1.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-lite2.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts new file +252 -0
252 lines not on this page · raw message
Signature · 1 line
2.17.1
Re: [PATCH 2/2] ARM: dts: sun50i: h6: Introduce Beelink GS1 board
Hi,
Quoted 47 lines · Clément Péron
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- FN-Link 6222B-SRB Wifi/BT
- 1x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- S/PDIF Tx
- IR receiver
- 5V/2A DC power supplySigned-off-by Clément Péron <[email protected]>---
Thanks to Jagan and Icenowy, most of this devicetree is taken from their works on the OrangePi One Plus and Pine H64.
arch/arm64/boot/dts/allwinner/Makefile | 1 + .../dts/allwinner/sun50i-h6-beelink-gs1.dts | 252 ++++++++++++++++++ 2 files changed, 253 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dtsarch/arm64/boot/dts/allwinner/Makefile +1
-0@@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-beelink-gs1.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-lite2.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtbarch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts new file +4
-0@@ -0,0 +1,252 @@ +// SPDX-License-Identifier: (GPL-2.0+ or MIT) +/* + * Copyright (C) 2019 Clément Péron <[email protected]> + */
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts line 14
Quoted 10 lines
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts new file +10
-0+ +/dts-v1/; + +#include "sun50i-h6.dtsi" + +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Beelink GS1"; + compatible = "azw,beelink-gs1", "allwinner,sun50i-h6";
Please add that board to Documentation/devicetree/bindings/arm/sunxi.yaml, it's new and in linux-next.
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts line 103
Quoted 12 lines
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts new file +12
-0+&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + vmmc-supply = <®_cldo1>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; + bus-width = <4>; + status = "okay"; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>;
If those (mmc0 and mmc2_pins) are the only muxing options as their names suggests, it should be set in the DTSI.
If not, the name of the pin group should be changed.
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts line 202
Quoted 13 lines
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts new file +13
-0+ reg_cldo2: cldo2 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-1"; + }; + + reg_cldo3: cldo3 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-2"; + };
I don't see any SDIO bus declared, why do you need those regulators on?
Can you also declare the PIO regulators?
Thanks!
Maxmie
--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
Re: [PATCH 2/2] ARM: dts: sun50i: h6: Introduce Beelink GS1 board
Hi,
Quoted 57 lines · Maxime Ripard
Hi,
Quoted 53 lines · Clément Péron
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- FN-Link 6222B-SRB Wifi/BT
- 1x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- S/PDIF Tx
- IR receiver
- 5V/2A DC power supplySigned-off-by Clément Péron <[email protected]>---
Thanks to Jagan and Icenowy, most of this devicetree is taken from their works on the OrangePi One Plus and Pine H64.
arch/arm64/boot/dts/allwinner/Makefile | 1 + .../dts/allwinner/sun50i-h6-beelink-gs1.dts | 252 ++++++++++++++++++ 2 files changed, 253 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dtsarch/arm64/boot/dts/allwinner/Makefile +1
-0@@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-beelink-gs1.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-lite2.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtbarch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts new file +10
-0@@ -0,0 +1,252 @@ +// SPDX-License-Identifier: (GPL-2.0+ or MIT) +/* + * Copyright (C) 2019 Clément Péron <[email protected]> + */ + +/dts-v1/; + +#include "sun50i-h6.dtsi" + +#include <dt-bindings/gpio/gpio.h>
Quoted 8 lines
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts line 14
Quoted 4 lines
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts new file +4
-0+ +/ { + model = "Beelink GS1"; + compatible = "azw,beelink-gs1", "allwinner,sun50i-h6";Please add that board to
Documentation/devicetree/bindings/arm/sunxi.yaml, it's new and in linux-next.
OK didn't know about that will do it.
Quoted 16 lines
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts line 103
Quoted 13 lines
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts new file +12
-0+&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + vmmc-supply = <®_cldo1>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; + bus-width = <4>; + status = "okay"; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>;If those (mmc0 and
mmc2_pins) are the only muxing options as their names suggests, it should be set in the DTSI.
Yes, it's the only muxing. I will add a patch to move these in the SOC dtsi.
Quoted 17 lines
If not, the name of the pin group should be changed.
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts line 202
Quoted 13 lines
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts new file +13
-0+ reg_cldo2: cldo2 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-1"; + }; + + reg_cldo3: cldo3 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-2"; + };
Quoted 1 line
I don't see any SDIO bus declared, why do you need those regulators on?
You're right forget to remove. Will do.
Quoted 2 lines
Can you also declare the PIO regulators?
Ok,
Thanks for the review.
Quoted 8 lines
Thanks!
Maxmie--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com