Skip to contentSkip to conversation

ARM: sun8i: h3: bluetooth for Banana Pi M2 Zero board

PATCH Superseded Andreas Kemnade 3 participants 5 messages Mar 1, 2019 – Apr 12, 2019

Subsystems (2)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 ARM: sun8i: h3: bluetooth for Banana Pi M2 Zero board

The Banana Pi M2 Zero board has an AP6212 BT+Wifi combo chip with broadcom internals attached to UART1 and some gpios. This addition is in line with similar boards

---
changes in v2: remove pinctrl things

 arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 15 +++++++++++++++
 1 file changed, 15 insertions(+)
arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts +15 -0
index 1db2541135a7..57432d0500b1 100644
@@ -69,6 +69,8 @@
 		compatible = "mmc-pwrseq-simple";
 		pinctrl-names = "default";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+		clocks = <&rtc 1>;
+		clock-names = "ext_clock";
 	};
 };
 
@@ -122,7 +124,20 @@
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	uart-has-rtscts;
 	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rtc 1>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_vcc3v3>;
+		vddio-supply = <&reg_vcc3v3>;
+		device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+		host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
+		shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	};
+
 };
 
 &usb_otg {
Signature · 1 line
2.11.0
#1 lore raw

ping

Quoted 48 lines · On Fri, 1 Mar 2019 19:52:12 +0100 Andreas Kemnade <[email protected]> wrote:

The Banana Pi M2 Zero board has an AP6212 BT+Wifi combo chip with broadcom internals attached to UART1 and some gpios. This addition is in line with similar boards

---
changes in v2: remove pinctrl things

 arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 15 +++++++++++++++
 1 file changed, 15 insertions(+)
arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts +15 -0
index 1db2541135a7..57432d0500b1 100644
@@ -69,6 +69,8 @@
 		compatible = "mmc-pwrseq-simple";
 		pinctrl-names = "default";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+		clocks = <&rtc 1>;
+		clock-names = "ext_clock";
 	};
 };
 
@@ -122,7 +124,20 @@
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	uart-has-rtscts;
 	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rtc 1>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_vcc3v3>;
+		vddio-supply = <&reg_vcc3v3>;
+		device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+		host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
+		shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	};
+
 };
 
 &usb_otg {
Signature · 1 line
2.11.0
#2 lore raw
Quoted 10 lines · Andreas Kemnade

ping

Quoted 5 lines · On Fri, 1 Mar 2019 19:52:12 +0100 Andreas Kemnade <[email protected]> wrote:

The Banana Pi M2 Zero board has an AP6212 BT+Wifi combo chip with broadcom internals attached to UART1 and some gpios. This addition is in line with similar boards

I never received that patch, who did you send it to?

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

#3 lore raw

Hi,

Quoted 6 lines · On Mon, 8 Apr 2019 10:14:04 +0200 Maxime Ripard <[email protected]>…
Quoted 5 lines · Andreas Kemnade

ping

On Fri, 1 Mar 2019 19:52:12 +0100
Andreas Kemnade <[email protected]> wrote:

Quoted 8 lines
Quoted 5 lines
Quoted 5 lines

The Banana Pi M2 Zero board has an AP6212 BT+Wifi combo chip with broadcom internals attached to UART1 and some gpios. This addition is in line with similar boards

I never received that patch, who did you send it to?

Seems that I only have sent you the first version of that patch. Somehow I must have left you out during copy and paste of adresses.

Regards,
Andreas