Skip to contentSkip to conversation

pico-imx7d: README: Adjust the binary name after DM conversion

PATCH New Fabio Estevam 2 participants 2 messages Apr 26, 2019 Arm i.MX and Layerscape

lore
Share & tools
lore

Fabio Estevam

author reviewer
#0 lore raw

PATCH 1/1 pico-imx7d: README: Adjust the binary name after DM conversion

After the conversion to DM the U-Boot binary is called u-boot-dtb.imx, so fix the README file accordingly.

---
 board/technexion/pico-imx7d/README | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
board/technexion/pico-imx7d/README +6 -6
index f21d8301cb..6aa0d25af5 100644
@@ -11,7 +11,7 @@ $ make mrproper
 $ make pico-imx7d_defconfig
 $ make
 
-This generates the SPL and u-boot.img binaries.
+This generates the SPL and u-boot-dtb.img binaries.
 
 1. Loading U-Boot via USB Serial Download Protocol
 
@@ -32,15 +32,15 @@ to use an externally powered USB hub between the board and the host computer.
 
 Open a terminal program such as minicom.
 
-Copy SPL and u-boot.img to the imx_usb_loader folder.
+Copy SPL and u-boot-dtb.img to the imx_usb_loader folder.
 
 Load the SPL binary via USB:
 
 $ sudo ./imx_usb SPL
 
-Load the u-boot.img binary via USB:
+Load the u-boot-dtb.img binary via USB:
 
-$ sudo ./imx_usb u-boot.img
+$ sudo ./imx_usb u-boot-dtb.img
 
 Then U-Boot starts and its messages appear in the console program.
 
@@ -55,11 +55,11 @@ Run the DFU agent so we can flash the new images using dfu-util tool:
 
 => dfu 0 mmc 0
 
-Flash SPL and u-boot.img into the eMMC running the following commands on a PC:
+Flash SPL and u-boot-dtb.img into the eMMC running the following commands on a PC:
 
 $ sudo dfu-util -D SPL -a spl
 
-$ sudo dfu-util -D u-boot.img -a u-boot
+$ sudo dfu-util -D u-boot-dtb.img -a u-boot
 
 Remove power from the pico board.
 
Signature · 1 line
2.17.1
#1 lore raw

PATCH 1/1 pico-imx7d: README: Adjust the binary name after DM conversion

Le 26/04/2019 à 14:36, Fabio Estevam a écrit :

Quoted 44 lines

After the conversion to DM the U-Boot binary is called u-boot-dtb.imx, so fix the README file accordingly.

---
  board/technexion/pico-imx7d/README | 12 ++++++------
  1 file changed, 6 insertions(+), 6 deletions(-)
board/technexion/pico-imx7d/README +4 -4
index f21d8301cb..6aa0d25af5 100644
@@ -11,7 +11,7 @@ $ make mrproper
  $ make pico-imx7d_defconfig
  $ make
 
-This generates the SPL and u-boot.img binaries.
+This generates the SPL and u-boot-dtb.img binaries.
 
  1. Loading U-Boot via USB Serial Download Protocol
 
@@ -32,15 +32,15 @@ to use an externally powered USB hub between the board and the host computer.
 
  Open a terminal program such as minicom.
 
-Copy SPL and u-boot.img to the imx_usb_loader folder.
+Copy SPL and u-boot-dtb.img to the imx_usb_loader folder.
 
  Load the SPL binary via USB:
 
  $ sudo ./imx_usb SPL
 
-Load the u-boot.img binary via USB:
+Load the u-boot-dtb.img binary via USB:
 
-$ sudo ./imx_usb u-boot.img
+$ sudo ./imx_usb u-boot-dtb.img
 
  Then U-Boot starts and its messages appear in the console program.
 
@@ -55,11 +55,11 @@ Run the DFU agent so we can flash the new images using dfu-util tool:
 
  => dfu 0 mmc 0
 

board/technexion/pico-imx7d/README Run the DFU agent so we can flash the new images using dfu-util tool: · line 65

Quoted 10 lines
board/technexion/pico-imx7d/README +2 -2
-Flash SPL and u-boot.img into the eMMC running the following commands on a PC:
+Flash SPL and u-boot-dtb.img into the eMMC running the following commands on a PC:
 
  $ sudo dfu-util -D SPL -a spl
 
-$ sudo dfu-util -D u-boot.img -a u-boot
+$ sudo dfu-util -D u-boot-dtb.img -a u-boot
 
  Remove power from the pico board.