Skip to contentSkip to conversation

arm: bcm: Enable reset and pinctrl for ARCH_BRCMSTB

PATCH In review Florian Fainelli 1 participant 4 messages May 31, 2019 – Jun 11, 2019

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

cover arm: bcm: Enable reset and pinctrl for ARCH_BRCMSTB

This patch series enabled PINCTRL and ARCH_HAS_RESET_CONTROLLER for ARCH_BRCMSTB since we have platforms that require these two subsystems.

Doug Berger (1):
ARM: bcm: Enable PINCTRL for ARCH_BRCMSTB

Jim Quinlan (1):
ARM: bcm: Enable ARCH_HAS_RESET_CONTROLLER for ARCH_BRCMSTB

 arch/arm/mach-bcm/Kconfig | 2 ++
 1 file changed, 2 insertions(+)
Signature · 7 lines
2.17.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#1 lore raw

PATCH 1/2 ARM: bcm: Enable ARCH_HAS_RESET_CONTROLLER for ARCH_BRCMSTB

From: Jim Quinlan <[email protected]>

Allow the use of reset controllers on ARCH_BRCMSTB such as the recently introduced RESET_BRCMSTB driver.

---
 arch/arm/mach-bcm/Kconfig | 1 +
 1 file changed, 1 insertion(+)
arch/arm/mach-bcm/Kconfig +1 -0
index ef4600cd2ce9..9c51d9d0aa68 100644
@@ -208,6 +208,7 @@ config ARCH_BCM_63XX
 config ARCH_BRCMSTB
 	bool "Broadcom BCM7XXX based boards"
 	depends on ARCH_MULTI_V7
+	select ARCH_HAS_RESET_CONTROLLER
 	select ARM_GIC
 	select ARM_ERRATA_798181 if SMP
 	select HAVE_ARM_ARCH_TIMER
Signature · 7 lines
2.17.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#2 lore raw

PATCH 2/2 ARM: bcm: Enable PINCTRL for ARCH_BRCMSTB

In reply to Florian Fainelli

From: Doug Berger <[email protected]>

ARCH_BRCMSTB needs to use the BCM2835 pin controller for chips like BCM7211 which adopted that pin controller for GPIO.

---
 arch/arm/mach-bcm/Kconfig | 1 +
 1 file changed, 1 insertion(+)
arch/arm/mach-bcm/Kconfig +1 -0
index 9c51d9d0aa68..31065c9a6936 100644
@@ -219,6 +219,7 @@ config ARCH_BRCMSTB
 	select ZONE_DMA if ARM_LPAE
 	select SOC_BRCMSTB
 	select SOC_BUS
+	select PINCTRL
 	help
 	  Say Y if you intend to run the kernel on a Broadcom ARM-based STB
 	  chipset.
Signature · 7 lines
2.17.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#3 lore raw
In reply to Florian Fainelli
Quoted 8 lines · Florian Fainelli

This patch series enabled PINCTRL and ARCH_HAS_RESET_CONTROLLER for ARCH_BRCMSTB since we have platforms that require these two subsystems.

Doug Berger (1):
ARM: bcm: Enable PINCTRL for ARCH_BRCMSTB

Jim Quinlan (1):
ARM: bcm: Enable ARCH_HAS_RESET_CONTROLLER for ARCH_BRCMSTB

Series applied to soc/next, thanks!

Signature · 7 lines
-- 
Florian

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel