drm/i915: Fix TypeC port mode switching
Subsystems (2)
cover drm/i915: Fix TypeC port mode switching
Atm we switch the TypeC port mode upon receiving an HPD interrupt. That's unsafe since the port could be active (after a modeset) or there could be other users that depend on the port mode to stay fixed. To make the mode switching robust add a TypeC port mode refcounting reflecting the active state of the port and locking for any other users of it (connector detection/AUX transfers).
The port mode will be reset if needed, whenever the TypeC lock is taken and the port is inactive. During a modeset resetting the port and selecting the proper PLL for the new mode must happen during the atomic commit phase, after the port and its PLL got disabled. For that we need to reserve both the TBT and MG PHY PLLs for the port and select the correct one after the port mode got reset/locked down for the duration of the port's active state.
The patchset has a few refactorings getting to the state described above gradually, so that reviewing the actual changes is somewhat easier. I also pushed the whole lot to [1].
The patchset also has a few fixes mostly related to the TBT-alt mode.
[1] https://github.com/ideak/linux/commits/typec-mode-switch
Imre Deak (23):
drm/i915/icl: Add support to read out the TBT PLL HW state drm/i915: Tune down WARNs about TBT AUX power well enabling drm/i915: Move the TypeC port handling code to a separate file drm/i915: Sanitize the terminology used for TypeC port modes drm/i915: Don't enable the DDI-IO power in the TypeC TBT-alt mode drm/i915: Fix the TBT AUX power well enabling
drm/i915: Use the correct AUX power domain in TypeC TBT-alt mode drm/i915: Unify the TypeC port notation in debug/error messages drm/i915: Factor out common parts from TypeC port handling functions drm/i915: Wait for TypeC PHY complete flag to clear in safe mode drm/i915: Handle the TCCOLD power-down event
drm/i915: Sanitize the TypeC connect/detect sequences drm/i915: Fix the TypeC port mode sanitization during loading/resume drm/i915: Keep the TypeC port mode fixed for detect/AUX transfers drm/i915: Sanitize the TypeC FIA lane configuration decoding drm/i915: Sanitize the shared DPLL reserve/release interface drm/i915: Sanitize the shared DPLL find/reference interface drm/i915/icl: Split getting the DPLLs to port type specific functions drm/i915/icl: Reserve all required PLLs for TypeC ports drm/i915: Keep the TypeC port mode fixed when the port is active drm/i915: Add state verification for the TypeC port mode drm/i915: Remove unneeded disconnect in TypeC legacy port mode drm/i915: WARN about invalid lane reversal in TBT-alt/DP-alt modes
drivers/gpu/drm/i915/Makefile | 3 +- drivers/gpu/drm/i915/Makefile.header-test | 1 + drivers/gpu/drm/i915/intel_ddi.c | 123 ++--- drivers/gpu/drm/i915/intel_ddi.h | 7 + drivers/gpu/drm/i915/intel_display.c | 160 ++++++- drivers/gpu/drm/i915/intel_display.h | 7 +- drivers/gpu/drm/i915/intel_display_power.c | 111 ++++- drivers/gpu/drm/i915/intel_dp.c | 243 +--------- drivers/gpu/drm/i915/intel_dp.h | 2 - drivers/gpu/drm/i915/intel_dp_mst.c | 6 + drivers/gpu/drm/i915/intel_dp_mst.h | 8 +- drivers/gpu/drm/i915/intel_dpll_mgr.c | 524 +++++++++++++++------ drivers/gpu/drm/i915/intel_dpll_mgr.h | 25 +- drivers/gpu/drm/i915/intel_drv.h | 21 +- drivers/gpu/drm/i915/intel_hdmi.c | 7 + drivers/gpu/drm/i915/intel_tc.c | 469 ++++++++++++++++++ drivers/gpu/drm/i915/intel_tc.h | 27 ++ 17 files changed, 1272 insertions(+), 472 deletions(-) create mode 100644 drivers/gpu/drm/i915/intel_tc.c create mode 100644 drivers/gpu/drm/i915/intel_tc.h
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 1/23 drm/i915/icl: Add support to read out the TBT PLL HW state
Add support to read out the TBT PLL HW state.
--- drivers/gpu/drm/i915/intel_display.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-)
drivers/gpu/drm/i915/intel_display.c +9 -2
@@ -9859,13 +9859,20 @@ static void icelake_get_ddi_pll(struct drm_i915_private *dev_priv,enum intel_dpll_id id;u32 temp; -/* TODO: TBT pll not implemented. */ if (intel_port_is_combophy (dev_priv, port)) { temp =I915_READ (DPCLKA_CFGCR0_ICL ) &DPCLKA_CFGCR0_DDI_CLK_SEL_MASK (port); id = temp >>DPCLKA_CFGCR0_DDI_CLK_SEL_SHIFT (port); }else if (intel_port_is_tc (dev_priv, port)) { - id =icl_tc_port_to_pll_id (intel_port_to_tc (dev_priv, port)); +u32 clk_sel =I915_READ (DDI_CLK_SEL (port)) &DDI_CLK_SEL_MASK ; + +if (clk_sel ==DDI_CLK_SEL_MG ) { + id =icl_tc_port_to_pll_id (intel_port_to_tc (dev_priv, + port)); + }else { +WARN_ON (clk_sel <DDI_CLK_SEL_TBT_162 ); + id =DPLL_ID_ICL_TBTPLL ; + } }else {WARN (1 ,"Invalid port %x\n" , port);return ;
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 01/23] drm/i915/icl: Add support to read out the TBT PLL HW state
Quoted 1 line · Imre Deak
Add support to read out the TBT PLL HW state.
Quoted 35 lines
Cc Vandita Kulkarni <[email protected]>Cc Paulo Zanoni <[email protected]>Cc Lucas De Marchi <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_display.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-)drivers/gpu/drm/i915/intel_display.c +4
-2@@ -9859,13 +9859,20 @@ static void icelake_get_ddi_pll(structdrm_i915_private *dev_priv, enum intel_dpll_id id;u32 temp; -/* TODO: TBT pll not implemented. */ if (intel_port_is_combophy (dev_priv, port)) { temp =I915_READ (DPCLKA_CFGCR0_ICL ) &DPCLKA_CFGCR0_DDI_CLK_SEL_MASK (port); id = temp >>DPCLKA_CFGCR0_DDI_CLK_SEL_SHIFT (port); }else if (intel_port_is_tc (dev_priv, port)) { - id =icl_tc_port_to_pll_id (intel_port_to_tc (dev_priv, port)); +u32 clk_sel =I915_READ (DDI_CLK_SEL (port)) &DDI_CLK_SEL_MASK ; + +if (clk_sel ==DDI_CLK_SEL_MG ) { + id =icl_tc_port_to_pll_id(intel_port_to_tc(dev_priv,
drivers/gpu/drm/i915/intel_display.c +1
-0+ port));
drivers/gpu/drm/i915/intel_display.c static void icelake_get_ddi_pll(struct drm_i915_private *dev_priv, · line 9878
Quoted 7 lines
drivers/gpu/drm/i915/intel_display.c +4
-0+ }else { +WARN_ON (clk_sel <DDI_CLK_SEL_TBT_162 ); + id =DPLL_ID_ICL_TBTPLL ; + } }else {WARN (1 ,"Invalid port %x\n" , port);return ;
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 2/23 drm/i915: Tune down WARNs about TBT AUX power well enabling
In reply to Imre DeakThe HW completion flag for the TBT AUX power well enabling/disabling gets stuck if the firmware tears down the TBT DP tunnel before the completion.
We shouldn't complain about the timeout, since it's expected to happen and doesn't cause further issues. We suppress the disabling timeout already, do the same for enabling.
--- drivers/gpu/drm/i915/intel_display_power.c | 15 ++++++++++----- 1 file changed, 10 insertions(+), 5 deletions(-)
drivers/gpu/drm/i915/intel_display_power.c +10 -5
@@ -268,11 +268,16 @@ static void hsw_wait_for_power_well_enable(struct drm_i915_private *dev_priv,int pw_idx = power_well->desc->hsw.idx;/* Timeout for PW1:10 us, AUX:not specified, other PWs:20 us. */ -WARN_ON (intel_wait_for_register (&dev_priv->uncore, - regs->driver, -HSW_PWR_WELL_CTL_STATE (pw_idx), -HSW_PWR_WELL_CTL_STATE (pw_idx), -1 )); +if (intel_wait_for_register (&dev_priv->uncore, + regs->driver, +HSW_PWR_WELL_CTL_STATE (pw_idx), +HSW_PWR_WELL_CTL_STATE (pw_idx), +1 )) { +DRM_DEBUG_KMS ("%s forced off\n" , power_well->desc->name); + +/* An AUX timeout is expected if the TBT DP tunnel is down. */ +WARN_ON (!power_well->desc->hsw.is_tc_tbt); + } } static u32 hsw_power_well_requesters(struct drm_i915_private *dev_priv,
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 02/23] drm/i915: Tune down WARNs about TBT AUX power well enabling
Quoted 8 lines · Imre Deak
The HW completion flag for the TBT AUX power well enabling/disabling gets stuck if the firmware tears down the TBT DP tunnel before the completion.
We shouldn't complain about the timeout, since it's expected to happen
and doesn't cause further issues. We suppress the disabling timeout already, do the same for enabling.
This was documented in spec?
Quoted 22 lines
Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_display_power.c | 15 ++++++++++----- 1 file changed, 10 insertions(+), 5 deletions(-)drivers/gpu/drm/i915/intel_display_power.c +0
-2@@ -268,11 +268,16 @@ static void hsw_wait_for_power_well_enable(struct drm_i915_private *dev_priv, int pw_idx = power_well->desc->hsw.idx;/* Timeout for PW1:10 us, AUX:not specified, other PWs:20 us. */ - WARN_ON(intel_wait_for_register(&dev_priv->uncore, - regs->driver,
drivers/gpu/drm/i915/intel_display_power.c static void · line 279
Quoted 10 lines
drivers/gpu/drm/i915/intel_display_power.c +6
-3-HSW_PWR_WELL_CTL_STATE (pw_idx), -HSW_PWR_WELL_CTL_STATE (pw_idx), - 1)); +if (intel_wait_for_register (&dev_priv->uncore, + regs->driver, +HSW_PWR_WELL_CTL_STATE (pw_idx), +HSW_PWR_WELL_CTL_STATE (pw_idx), +1 )) { +DRM_DEBUG_KMS ("%s forced off\n" , power_well->desc- >name);
Maybe "%s power well enable timeout"?
Anyways we can fix that latter.
Quoted 9 lines
drivers/gpu/drm/i915/intel_display_power.c +2
-0+ +/* An AUX timeout is expected if the TBT DP tunnel is down. */
drivers/gpu/drm/i915/intel_display_power.c +2
-0+WARN_ON (!power_well->desc->hsw.is_tc_tbt); + } } static u32 hsw_power_well_requesters(struct drm_i915_private
*dev_priv,
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 02/23] drm/i915: Tune down WARNs about TBT AUX power well enabling
Quoted 43 lines · Jose
Quoted 8 lines · Imre Deak
The HW completion flag for the TBT AUX power well enabling/disabling gets stuck if the firmware tears down the TBT DP tunnel before the completion.
We shouldn't complain about the timeout, since it's expected to happen
and doesn't cause further issues. We suppress the disabling timeout already, do the same for enabling.This was documented in spec?
Quoted 31 lines
Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_display_power.c | 15 ++++++++++----- 1 file changed, 10 insertions(+), 5 deletions(-)drivers/gpu/drm/i915/intel_display_power.c +6
-5@@ -268,11 +268,16 @@ static void hsw_wait_for_power_well_enable(struct drm_i915_private *dev_priv, int pw_idx = power_well->desc->hsw.idx;/* Timeout for PW1:10 us, AUX:not specified, other PWs:20 us. */ -WARN_ON (intel_wait_for_register (&dev_priv->uncore, - regs->driver, -HSW_PWR_WELL_CTL_STATE (pw_idx), -HSW_PWR_WELL_CTL_STATE (pw_idx), -1 )); +if (intel_wait_for_register (&dev_priv->uncore, + regs->driver, +HSW_PWR_WELL_CTL_STATE (pw_idx), +HSW_PWR_WELL_CTL_STATE (pw_idx), +1 )) { + DRM_DEBUG_KMS("%s forced off\n", power_well->desc-
Quoted 3 lines
drivers/gpu/drm/i915/intel_display_power.c static void · line 279
Quoted 1 line
drivers/gpu/drm/i915/intel_display_power.c +0
-0>name);Maybe "%s power well enable timeout"?
Yep, makes sense, will change this.
Quoted 11 lines
Anyways we can fix that latter.
Reviewed-by José Roberto de Souza <[email protected]>Quoted 7 lines
drivers/gpu/drm/i915/intel_display_power.c +2
-0+ +/* An AUX timeout is expected if the TBT DP tunnel is down. */
drivers/gpu/drm/i915/intel_display_power.c +2
-0+WARN_ON (!power_well->desc->hsw.is_tc_tbt); + } }
Quoted 2 lines
Quoted 2 lines
static u32 hsw_power_well_requesters(struct
drm_i915_private*dev_priv,
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 3/23 drm/i915: Move the TypeC port handling code to a separate file
In reply to Imre DeakMove the TypeC port handling functions to a new file for clarity.
While at it:
- s/icl_tc_port_connected()/intel_tc_port_connected()/ icl_tc_phy_disconnect(), will be unexported later.
- s/intel_dp_get_fia_supported_lane_count()/intel_tc_port_fia_max_lane_count()/ It's used for HDMI legacy mode too.
- Simplify function interfaces by passing only dig_port to them.
No functional changes.
--- drivers/gpu/drm/i915/Makefile | 3 +- drivers/gpu/drm/i915/Makefile.header-test | 1 + drivers/gpu/drm/i915/intel_ddi.c | 6 +- drivers/gpu/drm/i915/intel_dp.c | 227 +-------------------- drivers/gpu/drm/i915/intel_dp.h | 2 - drivers/gpu/drm/i915/intel_tc.c | 230 ++++++++++++++++++++++ drivers/gpu/drm/i915/intel_tc.h | 13 ++ 7 files changed, 252 insertions(+), 230 deletions(-) create mode 100644 drivers/gpu/drm/i915/intel_tc.c create mode 100644 drivers/gpu/drm/i915/intel_tc.h
drivers/gpu/drm/i915/Makefile +2 -1
@@ -171,7 +171,8 @@ i915-y += intel_audio.o \ intel_psr.o \ intel_quirks.o \ intel_sideband.o \ - intel_sprite.o + intel_sprite.o \ + intel_tc.o i915-$(CONFIG_ACPI) += intel_acpi.o intel_opregion.o i915-$(CONFIG_DRM_FBDEV_EMULATION) += intel_fbdev.o
drivers/gpu/drm/i915/Makefile.header-test +1 -0
@@ -58,6 +58,7 @@ header_test := \ intel_sdvo.h \ intel_sideband.h \ intel_sprite.h \ + intel_tc.h \ intel_tv.h \ intel_uncore.h \ intel_vdsc.h \
drivers/gpu/drm/i915/intel_ddi.c +3 -3
@@ -45,6 +45,7 @@#include "intel_lspcon.h" #include "intel_panel.h" #include "intel_psr.h" +#include "intel_tc.h" #include "intel_vdsc.h" struct ddi_buf_trans {
@@ -3904,7 +3905,6 @@ static int intel_ddi_compute_config(struct intel_encoder *encoder,static void intel_ddi_encoder_suspend (struct intel_encoder *encoder) {struct intel_digital_port *dig_port =enc_to_dig_port (&encoder->base); -struct drm_i915_private *i915 =to_i915 (encoder->base.dev);intel_dp_encoder_suspend (encoder);
@@ -3914,7 +3914,7 @@ static void intel_ddi_encoder_suspend(struct intel_encoder *encoder)* even if the sink has disappeared while being suspended. */ if (dig_port->tc_legacy_port) -icl_tc_phy_disconnect (i915, dig_port); +icl_tc_phy_disconnect (dig_port); }static void intel_ddi_encoder_reset (struct drm_encoder *drm_encoder)
@@ -3936,7 +3936,7 @@ static void intel_ddi_encoder_destroy(struct drm_encoder *encoder)intel_dp_encoder_flush_work (encoder);if (intel_port_is_tc (i915, dig_port->base.port)) -icl_tc_phy_disconnect (i915, dig_port); +icl_tc_phy_disconnect (dig_port);drm_encoder_cleanup (encoder);kfree (dig_port);
drivers/gpu/drm/i915/intel_dp.c +3 -224
257 lines not on this page · raw message
drivers/gpu/drm/i915/intel_dp.h +0 -2
@@ -112,8 +112,6 @@ bool intel_dp_get_colorimetry_status(struct intel_dp *intel_dp);int intel_dp_link_required (int pixel_clock,int bpp);int intel_dp_max_data_rate (int max_link_clock,int max_lanes);bool intel_digital_port_connected (struct intel_encoder *encoder); -void icl_tc_phy_disconnect (struct drm_i915_private *dev_priv, -struct intel_digital_port *dig_port);static inline unsigned int intel_dp_unused_lane_mask (int lane_count) {
drivers/gpu/drm/i915/intel_tc.c new file +230 -0
230 lines not on this page · raw message
drivers/gpu/drm/i915/intel_tc.h new file +13 -0
@@ -0,0 +1,13 @@ +#ifndef __INTEL_TC_H__ +#define __INTEL_TC_H__ + +#include <linux/types.h> + +struct intel_digital_port ; + +void icl_tc_phy_disconnect (struct intel_digital_port *dig_port); + +bool intel_tc_port_connected (struct intel_digital_port *dig_port); +int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port); + +#endif /* __INTEL_TC_H__ */
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Jani Nikula
maintainerRe: [PATCH 03/23] drm/i915: Move the TypeC port handling code to a separate file
Quoted 6 lines · Imre Deak
Move the TypeC port handling functions to a new file for clarity.
While at it:
- s/icl_tc_port_connected()/intel_tc_port_connected()/icl_tc_phy_disconnect(), will be unexported later.
Quoted 6 lines
- s/intel_dp_get_fia_supported_lane_count()/intel_tc_port_fia_max_lane_count()/ It's used for HDMI legacy mode too.
- Simplify function interfaces by passing only
dig_portto them.No functional changes.
Some nitpicks below.
BR,
Jani.
Quoted 365 lines
Cc Animesh Manna <[email protected]>Cc Paulo Zanoni <[email protected]>Cc José Roberto de Souza <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/Makefile | 3 +- drivers/gpu/drm/i915/Makefile.header-test | 1 + drivers/gpu/drm/i915/intel_ddi.c | 6 +- drivers/gpu/drm/i915/intel_dp.c | 227 +-------------------- drivers/gpu/drm/i915/intel_dp.h | 2 - drivers/gpu/drm/i915/intel_tc.c | 230 ++++++++++++++++++++++ drivers/gpu/drm/i915/intel_tc.h | 13 ++ 7 files changed, 252 insertions(+), 230 deletions(-) create mode 100644 drivers/gpu/drm/i915/intel_tc.c create mode 100644 drivers/gpu/drm/i915/intel_tc.hdrivers/gpu/drm/i915/Makefile +2
-1@@ -171,7 +171,8 @@ i915-y += intel_audio.o \ intel_psr.o \ intel_quirks.o \ intel_sideband.o \ - intel_sprite.o + intel_sprite.o \ + intel_tc.o i915-$(CONFIG_ACPI) += intel_acpi.o intel_opregion.o i915-$(CONFIG_DRM_FBDEV_EMULATION) += intel_fbdev.odrivers/gpu/drm/i915/Makefile.header-test +1
-0@@ -58,6 +58,7 @@ header_test := \ intel_sdvo.h \ intel_sideband.h \ intel_sprite.h \ + intel_tc.h \ intel_tv.h \ intel_uncore.h \ intel_vdsc.h \drivers/gpu/drm/i915/intel_ddi.c +3
-3@@ -45,6 +45,7 @@#include "intel_lspcon.h" #include "intel_panel.h" #include "intel_psr.h" +#include "intel_tc.h" #include "intel_vdsc.h" struct ddi_buf_trans {@@ -3904,7 +3905,6 @@ static int intel_ddi_compute_config(struct intel_encoder *encoder,static void intel_ddi_encoder_suspend (struct intel_encoder *encoder) {struct intel_digital_port *dig_port =enc_to_dig_port (&encoder->base); -struct drm_i915_private *i915 =to_i915 (encoder->base.dev);intel_dp_encoder_suspend (encoder);@@ -3914,7 +3914,7 @@ static void intel_ddi_encoder_suspend(struct intel_encoder *encoder)* even if the sink has disappeared while being suspended. */ if (dig_port->tc_legacy_port) -icl_tc_phy_disconnect (i915, dig_port); +icl_tc_phy_disconnect (dig_port); }static void intel_ddi_encoder_reset (struct drm_encoder *drm_encoder)@@ -3936,7 +3936,7 @@ static void intel_ddi_encoder_destroy(struct drm_encoder *encoder)intel_dp_encoder_flush_work (encoder);if (intel_port_is_tc (i915, dig_port->base.port)) -icl_tc_phy_disconnect (i915, dig_port); +icl_tc_phy_disconnect (dig_port);drm_encoder_cleanup (encoder);kfree (dig_port);drivers/gpu/drm/i915/intel_dp.c +3
-224@@ -62,6 +62,7 @@#include "intel_panel.h" #include "intel_psr.h" #include "intel_sideband.h" +#include "intel_tc.h" #include "intel_vdsc.h" #define DP_DPRX_ESI_LEN 14@@ -211,46 +212,13 @@ static int intel_dp_max_common_rate(struct intel_dp *intel_dp)return intel_dp->common_rates[intel_dp->num_common_rates -1 ]; } -static int intel_dp_get_fia_supported_lane_count (struct intel_dp *intel_dp) -{ -struct intel_digital_port *dig_port =dp_to_dig_port (intel_dp); -struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); -enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); -intel_wakeref_t wakeref; -u32 lane_info; - -if (tc_port ==PORT_TC_NONE || dig_port->tc_type !=TC_PORT_TYPEC ) -return 4 ; - - lane_info =0 ; -with_intel_display_power (dev_priv,POWER_DOMAIN_DISPLAY_CORE , wakeref) - lane_info = (I915_READ(PORT_TX_DFLEXDPSP) & -DP_LANE_ASSIGNMENT_MASK (tc_port)) >> -DP_LANE_ASSIGNMENT_SHIFT (tc_port); - -switch (lane_info) { -default : -MISSING_CASE (lane_info); -case 1 : -case 2 : -case 4 : -case 8 : -return 1 ; -case 3 : -case 12 : -return 2 ; -case 15 : -return 4 ; - } -} -/* Theoretical max between source and sink */ static int intel_dp_max_common_lane_count (struct intel_dp *intel_dp) {struct intel_digital_port *intel_dig_port =dp_to_dig_port (intel_dp);int source_max = intel_dig_port->max_lanes;int sink_max =drm_dp_max_lane_count (intel_dp->dpcd); -int fia_max =intel_dp_get_fia_supported_lane_count (intel_dp); +int fia_max =intel_tc_port_fia_max_lane_count (intel_dig_port);return min3 (source_max, sink_max, fia_max); }@@ -5231,195 +5199,6 @@ static bool icl_combo_port_connected(struct drm_i915_private *dev_priv,return I915_READ (SDEISR ) &SDE_DDI_HOTPLUG_ICP (port); } -static const char *tc_type_name (enum tc_port_type type) -{ -static const char *const names[] = { - [TC_PORT_UNKNOWN ] ="unknown" , - [TC_PORT_LEGACY ] ="legacy" , - [TC_PORT_TYPEC ] ="typec" , - [TC_PORT_TBT ] ="tbt" , - }; - -if (WARN_ON (type >=ARRAY_SIZE (names))) - type =TC_PORT_UNKNOWN ; - -return names[type]; -} - -static void icl_update_tc_port_type (struct drm_i915_private *dev_priv, -struct intel_digital_port *intel_dig_port, -bool is_legacy,bool is_typec,bool is_tbt) -{ -enum port port = intel_dig_port->base.port; -enum tc_port_type old_type = intel_dig_port->tc_type; - -WARN_ON (is_legacy + is_typec + is_tbt !=1 ); - -if (is_legacy) - intel_dig_port->tc_type =TC_PORT_LEGACY ; -else if (is_typec) - intel_dig_port->tc_type =TC_PORT_TYPEC ; -else if (is_tbt) - intel_dig_port->tc_type =TC_PORT_TBT ; -else -return ; - -/* Types are not supposed to be changed at runtime. */ -WARN_ON (old_type !=TC_PORT_UNKNOWN && - old_type != intel_dig_port->tc_type); - -if (old_type != intel_dig_port->tc_type) -DRM_DEBUG_KMS ("Port %c has TC type %s\n" ,port_name (port), -tc_type_name (intel_dig_port->tc_type)); -} - -/* -* This function implements the first part of the Connect Flow described by our -* specification, Gen11 TypeC Programming chapter. The rest of the flow (reading -* lanes, EDID, etc) is done as needed in the typical places. -* -* Unlike the other ports, type-C ports are not available to use as soon as we -* get a hotplug. The type-C PHYs can be shared between multiple controllers: -* display, USB, etc. As a result, handshaking through FIA is required around -* connect and disconnect to cleanly transfer ownership with the controller and -* set the type-C power state. -* -* We could opt to only do the connect flow when we actually try to use the AUX -* channels or do a modeset, then immediately run the disconnect flow after -* usage, but there are some implications on this for a dynamic environment: -* things may go away or change behind our backs. So for now our driver is -* always trying to acquire ownership of the controller as soon as it gets an -* interrupt (or polls state and sees a port is connected) and only gives it -* back when it sees a disconnect. Implementation of a more fine-grained model -* will require a lot of coordination with user space and thorough testing for -* the extra possible cases. -*/ -static bool icl_tc_phy_connect (struct drm_i915_private *dev_priv, -struct intel_digital_port *dig_port) -{ -enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); -u32 val; - -if (dig_port->tc_type !=TC_PORT_LEGACY && - dig_port->tc_type !=TC_PORT_TYPEC ) -return true; - - val =I915_READ (PORT_TX_DFLEXDPPMS ); -if (!(val &DP_PHY_MODE_STATUS_COMPLETED (tc_port))) { -DRM_DEBUG_KMS ("DP PHY for TC port %d not ready\n" , tc_port); -WARN_ON (dig_port->tc_legacy_port); -return false; - } - -/* -* This function may be called many times in a row without an HPD event -* in between, so try to avoid the write when we can. -*/ - val =I915_READ (PORT_TX_DFLEXDPCSSS ); -if (!(val &DP_PHY_MODE_STATUS_NOT_SAFE (tc_port))) { - val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); -I915_WRITE (PORT_TX_DFLEXDPCSSS , val); - } - -/* -* Now we have to re-check the live state, in case the port recently -* became disconnected. Not necessary for legacy mode. -*/ -if (dig_port->tc_type ==TC_PORT_TYPEC && - !(I915_READ (PORT_TX_DFLEXDPSP ) &TC_LIVE_STATE_TC (tc_port))) { -DRM_DEBUG_KMS ("TC PHY %d sudden disconnect.\n" , tc_port); -icl_tc_phy_disconnect (dev_priv, dig_port); -return false; - } - -return true; -} - -/* -* See the comment at the connect function. This implements the Disconnect -* Flow. -*/ -void icl_tc_phy_disconnect (struct drm_i915_private *dev_priv, -struct intel_digital_port *dig_port) -{ -enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); - -if (dig_port->tc_type ==TC_PORT_UNKNOWN ) -return ; - -/* -* TBT disconnection flow is read the live status, what was done in -* caller. -*/ -if (dig_port->tc_type ==TC_PORT_TYPEC || - dig_port->tc_type ==TC_PORT_LEGACY ) { -u32 val; - - val =I915_READ (PORT_TX_DFLEXDPCSSS ); - val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); -I915_WRITE (PORT_TX_DFLEXDPCSSS , val); - } - -DRM_DEBUG_KMS ("Port %c TC type %s disconnected\n" , -port_name (dig_port->base.port), -tc_type_name (dig_port->tc_type)); - - dig_port->tc_type =TC_PORT_UNKNOWN ; -} - -/* -* The type-C ports are different because even when they are connected, they may -* not be available/usable by the graphics driver: see the comment on -* icl_tc_phy_connect(). So in our driver instead of adding the additional -* concept of "usable" and make everything check for "connected and usable" we -* define a port as "connected" when it is not only connected, but also when it -* is usable by the rest of the driver. That maintains the old assumption that -* connected ports are usable, and avoids exposing to the users objects they -* can't really use. -*/ -static bool icl_tc_port_connected (struct drm_i915_private *dev_priv, -struct intel_digital_port *intel_dig_port) -{ -enum port port = intel_dig_port->base.port; -enum tc_port tc_port =intel_port_to_tc (dev_priv, port); -bool is_legacy, is_typec, is_tbt; -u32 dpsp; - -/* -* Complain if we got a legacy port HPD, but VBT didn't mark the port as -* legacy. Treat the port as legacy from now on. -*/ -if (!intel_dig_port->tc_legacy_port && -I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) { -DRM_ERROR ("VBT incorrectly claims port %c is not TypeC legacy\n" , -port_name (port)); - intel_dig_port->tc_legacy_port = true; - } - is_legacy = intel_dig_port->tc_legacy_port; - -/* -* The spec says we shouldn't be using the ISR bits for detecting -* between TC and TBT. We should use DFLEXDPSP. -*/ - dpsp =I915_READ (PORT_TX_DFLEXDPSP ); - is_typec = dpsp &TC_LIVE_STATE_TC (tc_port); - is_tbt = dpsp &TC_LIVE_STATE_TBT (tc_port); - -if (!is_legacy && !is_typec && !is_tbt) { -icl_tc_phy_disconnect (dev_priv, intel_dig_port); - -return false; - } - -icl_update_tc_port_type (dev_priv, intel_dig_port, is_legacy, is_typec, - is_tbt); - -if (!icl_tc_phy_connect (dev_priv, intel_dig_port)) -return false; - -return true; -} -static bool icl_digital_port_connected (struct intel_encoder *encoder) {struct drm_i915_private *dev_priv =to_i915 (encoder->base.dev);@@ -5428,7 +5207,7 @@ static bool icl_digital_port_connected(struct intel_encoder *encoder)if (intel_port_is_combophy (dev_priv, encoder->port))return icl_combo_port_connected (dev_priv, dig_port);else if (intel_port_is_tc (dev_priv, encoder->port)) -return icl_tc_port_connected (dev_priv, dig_port); +return intel_tc_port_connected (dig_port);else MISSING_CASE (encoder->hpd_pin);drivers/gpu/drm/i915/intel_dp.h +0
-2@@ -112,8 +112,6 @@ bool intel_dp_get_colorimetry_status(struct intel_dp *intel_dp);int intel_dp_link_required (int pixel_clock,int bpp);int intel_dp_max_data_rate (int max_link_clock,int max_lanes);bool intel_digital_port_connected (struct intel_encoder *encoder); -void icl_tc_phy_disconnect (struct drm_i915_private *dev_priv, -struct intel_digital_port *dig_port);static inline unsigned int intel_dp_unused_lane_mask (int lane_count) {drivers/gpu/drm/i915/intel_tc.c new file +0
-0
drivers/gpu/drm/i915/intel_tc.c line 4
Quoted 4 lines
drivers/gpu/drm/i915/intel_tc.c new file +4
-0@@ -0,0 +1,230 @@ +// SPDX-License-Identifier: MIT +/* +* Copyright © 2019 Intel Corporation +*/
From the Nitpicks Department, please add a blank line here.
drivers/gpu/drm/i915/intel_tc.c line 7
Quoted 3 lines
drivers/gpu/drm/i915/intel_tc.c new file +3
-0+#include "intel_display.h" +#include "i915_drv.h" +#include "intel_tc.h"
And sort the includes.
drivers/gpu/drm/i915/intel_tc.h
Quoted 229 lines
drivers/gpu/drm/i915/intel_tc.c new file +223
-0+ +static const char *tc_type_name (enum tc_port_type type) +{ +static const char *const names[] = { + [TC_PORT_UNKNOWN ] ="unknown" , + [TC_PORT_LEGACY ] ="legacy" , + [TC_PORT_TYPEC ] ="typec" , + [TC_PORT_TBT ] ="tbt" , + }; + +if (WARN_ON (type >=ARRAY_SIZE (names))) + type =TC_PORT_UNKNOWN ; + +return names[type]; +} + +int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +intel_wakeref_t wakeref; +u32 lane_info; + +if (tc_port ==PORT_TC_NONE || dig_port->tc_type !=TC_PORT_TYPEC ) +return 4 ; + + lane_info =0 ; +with_intel_display_power (dev_priv,POWER_DOMAIN_DISPLAY_CORE , wakeref) + lane_info = (I915_READ(PORT_TX_DFLEXDPSP) & +DP_LANE_ASSIGNMENT_MASK (tc_port)) >> +DP_LANE_ASSIGNMENT_SHIFT (tc_port); + +switch (lane_info) { +default : +MISSING_CASE (lane_info); +case 1 : +case 2 : +case 4 : +case 8 : +return 1 ; +case 3 : +case 12 : +return 2 ; +case 15 : +return 4 ; + } +} + +/* +* This function implements the first part of the Connect Flow described by our +* specification, Gen11 TypeC Programming chapter. The rest of the flow (reading +* lanes, EDID, etc) is done as needed in the typical places. +* +* Unlike the other ports, type-C ports are not available to use as soon as we +* get a hotplug. The type-C PHYs can be shared between multiple controllers: +* display, USB, etc. As a result, handshaking through FIA is required around +* connect and disconnect to cleanly transfer ownership with the controller and +* set the type-C power state. +* +* We could opt to only do the connect flow when we actually try to use the AUX +* channels or do a modeset, then immediately run the disconnect flow after +* usage, but there are some implications on this for a dynamic environment: +* things may go away or change behind our backs. So for now our driver is +* always trying to acquire ownership of the controller as soon as it gets an +* interrupt (or polls state and sees a port is connected) and only gives it +* back when it sees a disconnect. Implementation of a more fine-grained model +* will require a lot of coordination with user space and thorough testing for +* the extra possible cases. +*/ +static bool icl_tc_phy_connect (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +u32 val; + +if (dig_port->tc_type !=TC_PORT_LEGACY && + dig_port->tc_type !=TC_PORT_TYPEC ) +return true; + + val =I915_READ (PORT_TX_DFLEXDPPMS ); +if (!(val &DP_PHY_MODE_STATUS_COMPLETED (tc_port))) { +DRM_DEBUG_KMS ("DP PHY for TC port %d not ready\n" , tc_port); +WARN_ON (dig_port->tc_legacy_port); +return false; + } + +/* +* This function may be called many times in a row without an HPD event +* in between, so try to avoid the write when we can. +*/ + val =I915_READ (PORT_TX_DFLEXDPCSSS ); +if (!(val &DP_PHY_MODE_STATUS_NOT_SAFE (tc_port))) { + val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); +I915_WRITE (PORT_TX_DFLEXDPCSSS , val); + } + +/* +* Now we have to re-check the live state, in case the port recently +* became disconnected. Not necessary for legacy mode. +*/ +if (dig_port->tc_type ==TC_PORT_TYPEC && + !(I915_READ (PORT_TX_DFLEXDPSP ) &TC_LIVE_STATE_TC (tc_port))) { +DRM_DEBUG_KMS ("TC PHY %d sudden disconnect.\n" , tc_port); +icl_tc_phy_disconnect (dig_port); +return false; + } + +return true; +} + +/* +* See the comment at the connect function. This implements the Disconnect +* Flow. +*/ +void icl_tc_phy_disconnect (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); + +if (dig_port->tc_type ==TC_PORT_UNKNOWN ) +return ; + +/* +* TBT disconnection flow is read the live status, what was done in +* caller. +*/ +if (dig_port->tc_type ==TC_PORT_TYPEC || + dig_port->tc_type ==TC_PORT_LEGACY ) { +u32 val; + + val =I915_READ (PORT_TX_DFLEXDPCSSS ); + val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); +I915_WRITE (PORT_TX_DFLEXDPCSSS , val); + } + +DRM_DEBUG_KMS ("Port %c TC type %s disconnected\n" , +port_name (dig_port->base.port), +tc_type_name (dig_port->tc_type)); + + dig_port->tc_type =TC_PORT_UNKNOWN ; +} + +static void icl_update_tc_port_type (struct drm_i915_private *dev_priv, +struct intel_digital_port *intel_dig_port, +bool is_legacy,bool is_typec,bool is_tbt) +{ +enum port port = intel_dig_port->base.port; +enum tc_port_type old_type = intel_dig_port->tc_type; + +WARN_ON (is_legacy + is_typec + is_tbt !=1 ); + +if (is_legacy) + intel_dig_port->tc_type =TC_PORT_LEGACY ; +else if (is_typec) + intel_dig_port->tc_type =TC_PORT_TYPEC ; +else if (is_tbt) + intel_dig_port->tc_type =TC_PORT_TBT ; +else +return ; + +/* Types are not supposed to be changed at runtime. */ +WARN_ON (old_type !=TC_PORT_UNKNOWN && + old_type != intel_dig_port->tc_type); + +if (old_type != intel_dig_port->tc_type) +DRM_DEBUG_KMS ("Port %c has TC type %s\n" ,port_name (port), +tc_type_name (intel_dig_port->tc_type)); +} + + +/* +* The type-C ports are different because even when they are connected, they may +* not be available/usable by the graphics driver: see the comment on +* icl_tc_phy_connect(). So in our driver instead of adding the additional +* concept of "usable" and make everything check for "connected and usable" we +* define a port as "connected" when it is not only connected, but also when it +* is usable by the rest of the driver. That maintains the old assumption that +* connected ports are usable, and avoids exposing to the users objects they +* can't really use. +*/ +bool intel_tc_port_connected (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum port port = dig_port->base.port; +enum tc_port tc_port =intel_port_to_tc (dev_priv, port); +bool is_legacy, is_typec, is_tbt; +u32 dpsp; + +/* +* Complain if we got a legacy port HPD, but VBT didn't mark the port as +* legacy. Treat the port as legacy from now on. +*/ +if (!dig_port->tc_legacy_port && +I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) { +DRM_ERROR ("VBT incorrectly claims port %c is not TypeC legacy\n" , +port_name (port)); + dig_port->tc_legacy_port = true; + } + is_legacy = dig_port->tc_legacy_port; + +/* +* The spec says we shouldn't be using the ISR bits for detecting +* between TC and TBT. We should use DFLEXDPSP. +*/ + dpsp =I915_READ (PORT_TX_DFLEXDPSP ); + is_typec = dpsp &TC_LIVE_STATE_TC (tc_port); + is_tbt = dpsp &TC_LIVE_STATE_TBT (tc_port); + +if (!is_legacy && !is_typec && !is_tbt) { +icl_tc_phy_disconnect (dig_port); + +return false; + } + +icl_update_tc_port_type (dev_priv, dig_port, is_legacy, is_typec, + is_tbt); + +if (!icl_tc_phy_connect (dig_port)) +return false; + +return true; +} +drivers/gpu/drm/i915/intel_tc.h new file +0
-0@@ -0,0 +1,13 @@
SPDX header here please.
drivers/gpu/drm/i915/intel_tc.h line 8
Quoted 8 lines
drivers/gpu/drm/i915/intel_tc.h new file +8
-0+#ifndef __INTEL_TC_H__ +#define __INTEL_TC_H__ + +#include <linux/types.h> + +struct intel_digital_port ; + +void icl_tc_phy_disconnect (struct intel_digital_port *dig_port);
I'd like to see this named intel_tc_* in the future.
BR,
Jani.
Quoted 5 lines
drivers/gpu/drm/i915/intel_tc.h new file +5
-0+ +bool intel_tc_port_connected (struct intel_digital_port *dig_port); +int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port); + +#endif /* __INTEL_TC_H__ */
Signature · 5 lines
Jani Nikula, Intel Open Source Graphics Center _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 03/23] drm/i915: Move the TypeC port handling code to a separate file
Quoted 7 lines · Jani Nikula
Quoted 6 lines · Imre Deak
Move the TypeC port handling functions to a new file for clarity.
While at it:
- s/icl_tc_port_connected()/intel_tc_port_connected()/icl_tc_phy_disconnect(), will be unexported later.
Quoted 8 lines
Quoted 6 lines
- s/intel_dp_get_fia_supported_lane_count()/intel_tc_port_fia_max_lane_count()/ It's used for HDMI legacy mode too.
- Simplify function interfaces by passing only
dig_portto them.No functional changes.
Some nitpicks below.
Forgot,
on the idea.
Quoted 635 lines
BR,
Jani.Quoted 365 lines
Cc Animesh Manna <[email protected]>Cc Paulo Zanoni <[email protected]>Cc José Roberto de Souza <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/Makefile | 3 +- drivers/gpu/drm/i915/Makefile.header-test | 1 + drivers/gpu/drm/i915/intel_ddi.c | 6 +- drivers/gpu/drm/i915/intel_dp.c | 227 +-------------------- drivers/gpu/drm/i915/intel_dp.h | 2 - drivers/gpu/drm/i915/intel_tc.c | 230 ++++++++++++++++++++++ drivers/gpu/drm/i915/intel_tc.h | 13 ++ 7 files changed, 252 insertions(+), 230 deletions(-) create mode 100644 drivers/gpu/drm/i915/intel_tc.c create mode 100644 drivers/gpu/drm/i915/intel_tc.hdrivers/gpu/drm/i915/Makefile +2
-1@@ -171,7 +171,8 @@ i915-y += intel_audio.o \ intel_psr.o \ intel_quirks.o \ intel_sideband.o \ - intel_sprite.o + intel_sprite.o \ + intel_tc.o i915-$(CONFIG_ACPI) += intel_acpi.o intel_opregion.o i915-$(CONFIG_DRM_FBDEV_EMULATION) += intel_fbdev.odrivers/gpu/drm/i915/Makefile.header-test +1
-0@@ -58,6 +58,7 @@ header_test := \ intel_sdvo.h \ intel_sideband.h \ intel_sprite.h \ + intel_tc.h \ intel_tv.h \ intel_uncore.h \ intel_vdsc.h \drivers/gpu/drm/i915/intel_ddi.c +3
-3@@ -45,6 +45,7 @@#include "intel_lspcon.h" #include "intel_panel.h" #include "intel_psr.h" +#include "intel_tc.h" #include "intel_vdsc.h" struct ddi_buf_trans {@@ -3904,7 +3905,6 @@ static int intel_ddi_compute_config(struct intel_encoder *encoder,static void intel_ddi_encoder_suspend (struct intel_encoder *encoder) {struct intel_digital_port *dig_port =enc_to_dig_port (&encoder->base); -struct drm_i915_private *i915 =to_i915 (encoder->base.dev);intel_dp_encoder_suspend (encoder);@@ -3914,7 +3914,7 @@ static void intel_ddi_encoder_suspend(struct intel_encoder *encoder)* even if the sink has disappeared while being suspended. */ if (dig_port->tc_legacy_port) -icl_tc_phy_disconnect (i915, dig_port); +icl_tc_phy_disconnect (dig_port); }static void intel_ddi_encoder_reset (struct drm_encoder *drm_encoder)@@ -3936,7 +3936,7 @@ static void intel_ddi_encoder_destroy(struct drm_encoder *encoder)intel_dp_encoder_flush_work (encoder);if (intel_port_is_tc (i915, dig_port->base.port)) -icl_tc_phy_disconnect (i915, dig_port); +icl_tc_phy_disconnect (dig_port);drm_encoder_cleanup (encoder);kfree (dig_port);drivers/gpu/drm/i915/intel_dp.c +3
-224@@ -62,6 +62,7 @@#include "intel_panel.h" #include "intel_psr.h" #include "intel_sideband.h" +#include "intel_tc.h" #include "intel_vdsc.h" #define DP_DPRX_ESI_LEN 14@@ -211,46 +212,13 @@ static int intel_dp_max_common_rate(struct intel_dp *intel_dp)return intel_dp->common_rates[intel_dp->num_common_rates -1 ]; } -static int intel_dp_get_fia_supported_lane_count (struct intel_dp *intel_dp) -{ -struct intel_digital_port *dig_port =dp_to_dig_port (intel_dp); -struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); -enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); -intel_wakeref_t wakeref; -u32 lane_info; - -if (tc_port ==PORT_TC_NONE || dig_port->tc_type !=TC_PORT_TYPEC ) -return 4 ; - - lane_info =0 ; -with_intel_display_power (dev_priv,POWER_DOMAIN_DISPLAY_CORE , wakeref) - lane_info = (I915_READ(PORT_TX_DFLEXDPSP) & -DP_LANE_ASSIGNMENT_MASK (tc_port)) >> -DP_LANE_ASSIGNMENT_SHIFT (tc_port); - -switch (lane_info) { -default : -MISSING_CASE (lane_info); -case 1 : -case 2 : -case 4 : -case 8 : -return 1 ; -case 3 : -case 12 : -return 2 ; -case 15 : -return 4 ; - } -} -/* Theoretical max between source and sink */ static int intel_dp_max_common_lane_count (struct intel_dp *intel_dp) {struct intel_digital_port *intel_dig_port =dp_to_dig_port (intel_dp);int source_max = intel_dig_port->max_lanes;int sink_max =drm_dp_max_lane_count (intel_dp->dpcd); -int fia_max =intel_dp_get_fia_supported_lane_count (intel_dp); +int fia_max =intel_tc_port_fia_max_lane_count (intel_dig_port);return min3 (source_max, sink_max, fia_max); }@@ -5231,195 +5199,6 @@ static bool icl_combo_port_connected(struct drm_i915_private *dev_priv,return I915_READ (SDEISR ) &SDE_DDI_HOTPLUG_ICP (port); } -static const char *tc_type_name (enum tc_port_type type) -{ -static const char *const names[] = { - [TC_PORT_UNKNOWN ] ="unknown" , - [TC_PORT_LEGACY ] ="legacy" , - [TC_PORT_TYPEC ] ="typec" , - [TC_PORT_TBT ] ="tbt" , - }; - -if (WARN_ON (type >=ARRAY_SIZE (names))) - type =TC_PORT_UNKNOWN ; - -return names[type]; -} - -static void icl_update_tc_port_type (struct drm_i915_private *dev_priv, -struct intel_digital_port *intel_dig_port, -bool is_legacy,bool is_typec,bool is_tbt) -{ -enum port port = intel_dig_port->base.port; -enum tc_port_type old_type = intel_dig_port->tc_type; - -WARN_ON (is_legacy + is_typec + is_tbt !=1 ); - -if (is_legacy) - intel_dig_port->tc_type =TC_PORT_LEGACY ; -else if (is_typec) - intel_dig_port->tc_type =TC_PORT_TYPEC ; -else if (is_tbt) - intel_dig_port->tc_type =TC_PORT_TBT ; -else -return ; - -/* Types are not supposed to be changed at runtime. */ -WARN_ON (old_type !=TC_PORT_UNKNOWN && - old_type != intel_dig_port->tc_type); - -if (old_type != intel_dig_port->tc_type) -DRM_DEBUG_KMS ("Port %c has TC type %s\n" ,port_name (port), -tc_type_name (intel_dig_port->tc_type)); -} - -/* -* This function implements the first part of the Connect Flow described by our -* specification, Gen11 TypeC Programming chapter. The rest of the flow (reading -* lanes, EDID, etc) is done as needed in the typical places. -* -* Unlike the other ports, type-C ports are not available to use as soon as we -* get a hotplug. The type-C PHYs can be shared between multiple controllers: -* display, USB, etc. As a result, handshaking through FIA is required around -* connect and disconnect to cleanly transfer ownership with the controller and -* set the type-C power state. -* -* We could opt to only do the connect flow when we actually try to use the AUX -* channels or do a modeset, then immediately run the disconnect flow after -* usage, but there are some implications on this for a dynamic environment: -* things may go away or change behind our backs. So for now our driver is -* always trying to acquire ownership of the controller as soon as it gets an -* interrupt (or polls state and sees a port is connected) and only gives it -* back when it sees a disconnect. Implementation of a more fine-grained model -* will require a lot of coordination with user space and thorough testing for -* the extra possible cases. -*/ -static bool icl_tc_phy_connect (struct drm_i915_private *dev_priv, -struct intel_digital_port *dig_port) -{ -enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); -u32 val; - -if (dig_port->tc_type !=TC_PORT_LEGACY && - dig_port->tc_type !=TC_PORT_TYPEC ) -return true; - - val =I915_READ (PORT_TX_DFLEXDPPMS ); -if (!(val &DP_PHY_MODE_STATUS_COMPLETED (tc_port))) { -DRM_DEBUG_KMS ("DP PHY for TC port %d not ready\n" , tc_port); -WARN_ON (dig_port->tc_legacy_port); -return false; - } - -/* -* This function may be called many times in a row without an HPD event -* in between, so try to avoid the write when we can. -*/ - val =I915_READ (PORT_TX_DFLEXDPCSSS ); -if (!(val &DP_PHY_MODE_STATUS_NOT_SAFE (tc_port))) { - val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); -I915_WRITE (PORT_TX_DFLEXDPCSSS , val); - } - -/* -* Now we have to re-check the live state, in case the port recently -* became disconnected. Not necessary for legacy mode. -*/ -if (dig_port->tc_type ==TC_PORT_TYPEC && - !(I915_READ (PORT_TX_DFLEXDPSP ) &TC_LIVE_STATE_TC (tc_port))) { -DRM_DEBUG_KMS ("TC PHY %d sudden disconnect.\n" , tc_port); -icl_tc_phy_disconnect (dev_priv, dig_port); -return false; - } - -return true; -} - -/* -* See the comment at the connect function. This implements the Disconnect -* Flow. -*/ -void icl_tc_phy_disconnect (struct drm_i915_private *dev_priv, -struct intel_digital_port *dig_port) -{ -enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); - -if (dig_port->tc_type ==TC_PORT_UNKNOWN ) -return ; - -/* -* TBT disconnection flow is read the live status, what was done in -* caller. -*/ -if (dig_port->tc_type ==TC_PORT_TYPEC || - dig_port->tc_type ==TC_PORT_LEGACY ) { -u32 val; - - val =I915_READ (PORT_TX_DFLEXDPCSSS ); - val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); -I915_WRITE (PORT_TX_DFLEXDPCSSS , val); - } - -DRM_DEBUG_KMS ("Port %c TC type %s disconnected\n" , -port_name (dig_port->base.port), -tc_type_name (dig_port->tc_type)); - - dig_port->tc_type =TC_PORT_UNKNOWN ; -} - -/* -* The type-C ports are different because even when they are connected, they may -* not be available/usable by the graphics driver: see the comment on -* icl_tc_phy_connect(). So in our driver instead of adding the additional -* concept of "usable" and make everything check for "connected and usable" we -* define a port as "connected" when it is not only connected, but also when it -* is usable by the rest of the driver. That maintains the old assumption that -* connected ports are usable, and avoids exposing to the users objects they -* can't really use. -*/ -static bool icl_tc_port_connected (struct drm_i915_private *dev_priv, -struct intel_digital_port *intel_dig_port) -{ -enum port port = intel_dig_port->base.port; -enum tc_port tc_port =intel_port_to_tc (dev_priv, port); -bool is_legacy, is_typec, is_tbt; -u32 dpsp; - -/* -* Complain if we got a legacy port HPD, but VBT didn't mark the port as -* legacy. Treat the port as legacy from now on. -*/ -if (!intel_dig_port->tc_legacy_port && -I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) { -DRM_ERROR ("VBT incorrectly claims port %c is not TypeC legacy\n" , -port_name (port)); - intel_dig_port->tc_legacy_port = true; - } - is_legacy = intel_dig_port->tc_legacy_port; - -/* -* The spec says we shouldn't be using the ISR bits for detecting -* between TC and TBT. We should use DFLEXDPSP. -*/ - dpsp =I915_READ (PORT_TX_DFLEXDPSP ); - is_typec = dpsp &TC_LIVE_STATE_TC (tc_port); - is_tbt = dpsp &TC_LIVE_STATE_TBT (tc_port); - -if (!is_legacy && !is_typec && !is_tbt) { -icl_tc_phy_disconnect (dev_priv, intel_dig_port); - -return false; - } - -icl_update_tc_port_type (dev_priv, intel_dig_port, is_legacy, is_typec, - is_tbt); - -if (!icl_tc_phy_connect (dev_priv, intel_dig_port)) -return false; - -return true; -} -static bool icl_digital_port_connected (struct intel_encoder *encoder) {struct drm_i915_private *dev_priv =to_i915 (encoder->base.dev);@@ -5428,7 +5207,7 @@ static bool icl_digital_port_connected(struct intel_encoder *encoder)if (intel_port_is_combophy (dev_priv, encoder->port))return icl_combo_port_connected (dev_priv, dig_port);else if (intel_port_is_tc (dev_priv, encoder->port)) -return icl_tc_port_connected (dev_priv, dig_port); +return intel_tc_port_connected (dig_port);else MISSING_CASE (encoder->hpd_pin);drivers/gpu/drm/i915/intel_dp.h +0
-2@@ -112,8 +112,6 @@ bool intel_dp_get_colorimetry_status(struct intel_dp *intel_dp);int intel_dp_link_required (int pixel_clock,int bpp);int intel_dp_max_data_rate (int max_link_clock,int max_lanes);bool intel_digital_port_connected (struct intel_encoder *encoder); -void icl_tc_phy_disconnect (struct drm_i915_private *dev_priv, -struct intel_digital_port *dig_port);static inline unsigned int intel_dp_unused_lane_mask (int lane_count) {drivers/gpu/drm/i915/intel_tc.c new file +0
-0drivers/gpu/drm/i915/intel_tc.c line 4
Quoted 4 lines
drivers/gpu/drm/i915/intel_tc.c new file +4
-0@@ -0,0 +1,230 @@ +// SPDX-License-Identifier: MIT +/* +* Copyright © 2019 Intel Corporation +*/ From the Nitpicks Department, please add a blank line here.
drivers/gpu/drm/i915/intel_tc.c line 7
Quoted 3 lines
drivers/gpu/drm/i915/intel_tc.c new file +3
-0+#include "intel_display.h" +#include "i915_drv.h" +#include "intel_tc.h" And sort the includes.
drivers/gpu/drm/i915/intel_tc.h
Quoted 229 lines
drivers/gpu/drm/i915/intel_tc.c new file +223
-0+ +static const char *tc_type_name (enum tc_port_type type) +{ +static const char *const names[] = { + [TC_PORT_UNKNOWN ] ="unknown" , + [TC_PORT_LEGACY ] ="legacy" , + [TC_PORT_TYPEC ] ="typec" , + [TC_PORT_TBT ] ="tbt" , + }; + +if (WARN_ON (type >=ARRAY_SIZE (names))) + type =TC_PORT_UNKNOWN ; + +return names[type]; +} + +int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +intel_wakeref_t wakeref; +u32 lane_info; + +if (tc_port ==PORT_TC_NONE || dig_port->tc_type !=TC_PORT_TYPEC ) +return 4 ; + + lane_info =0 ; +with_intel_display_power (dev_priv,POWER_DOMAIN_DISPLAY_CORE , wakeref) + lane_info = (I915_READ(PORT_TX_DFLEXDPSP) & +DP_LANE_ASSIGNMENT_MASK (tc_port)) >> +DP_LANE_ASSIGNMENT_SHIFT (tc_port); + +switch (lane_info) { +default : +MISSING_CASE (lane_info); +case 1 : +case 2 : +case 4 : +case 8 : +return 1 ; +case 3 : +case 12 : +return 2 ; +case 15 : +return 4 ; + } +} + +/* +* This function implements the first part of the Connect Flow described by our +* specification, Gen11 TypeC Programming chapter. The rest of the flow (reading +* lanes, EDID, etc) is done as needed in the typical places. +* +* Unlike the other ports, type-C ports are not available to use as soon as we +* get a hotplug. The type-C PHYs can be shared between multiple controllers: +* display, USB, etc. As a result, handshaking through FIA is required around +* connect and disconnect to cleanly transfer ownership with the controller and +* set the type-C power state. +* +* We could opt to only do the connect flow when we actually try to use the AUX +* channels or do a modeset, then immediately run the disconnect flow after +* usage, but there are some implications on this for a dynamic environment: +* things may go away or change behind our backs. So for now our driver is +* always trying to acquire ownership of the controller as soon as it gets an +* interrupt (or polls state and sees a port is connected) and only gives it +* back when it sees a disconnect. Implementation of a more fine-grained model +* will require a lot of coordination with user space and thorough testing for +* the extra possible cases. +*/ +static bool icl_tc_phy_connect (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +u32 val; + +if (dig_port->tc_type !=TC_PORT_LEGACY && + dig_port->tc_type !=TC_PORT_TYPEC ) +return true; + + val =I915_READ (PORT_TX_DFLEXDPPMS ); +if (!(val &DP_PHY_MODE_STATUS_COMPLETED (tc_port))) { +DRM_DEBUG_KMS ("DP PHY for TC port %d not ready\n" , tc_port); +WARN_ON (dig_port->tc_legacy_port); +return false; + } + +/* +* This function may be called many times in a row without an HPD event +* in between, so try to avoid the write when we can. +*/ + val =I915_READ (PORT_TX_DFLEXDPCSSS ); +if (!(val &DP_PHY_MODE_STATUS_NOT_SAFE (tc_port))) { + val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); +I915_WRITE (PORT_TX_DFLEXDPCSSS , val); + } + +/* +* Now we have to re-check the live state, in case the port recently +* became disconnected. Not necessary for legacy mode. +*/ +if (dig_port->tc_type ==TC_PORT_TYPEC && + !(I915_READ (PORT_TX_DFLEXDPSP ) &TC_LIVE_STATE_TC (tc_port))) { +DRM_DEBUG_KMS ("TC PHY %d sudden disconnect.\n" , tc_port); +icl_tc_phy_disconnect (dig_port); +return false; + } + +return true; +} + +/* +* See the comment at the connect function. This implements the Disconnect +* Flow. +*/ +void icl_tc_phy_disconnect (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); + +if (dig_port->tc_type ==TC_PORT_UNKNOWN ) +return ; + +/* +* TBT disconnection flow is read the live status, what was done in +* caller. +*/ +if (dig_port->tc_type ==TC_PORT_TYPEC || + dig_port->tc_type ==TC_PORT_LEGACY ) { +u32 val; + + val =I915_READ (PORT_TX_DFLEXDPCSSS ); + val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); +I915_WRITE (PORT_TX_DFLEXDPCSSS , val); + } + +DRM_DEBUG_KMS ("Port %c TC type %s disconnected\n" , +port_name (dig_port->base.port), +tc_type_name (dig_port->tc_type)); + + dig_port->tc_type =TC_PORT_UNKNOWN ; +} + +static void icl_update_tc_port_type (struct drm_i915_private *dev_priv, +struct intel_digital_port *intel_dig_port, +bool is_legacy,bool is_typec,bool is_tbt) +{ +enum port port = intel_dig_port->base.port; +enum tc_port_type old_type = intel_dig_port->tc_type; + +WARN_ON (is_legacy + is_typec + is_tbt !=1 ); + +if (is_legacy) + intel_dig_port->tc_type =TC_PORT_LEGACY ; +else if (is_typec) + intel_dig_port->tc_type =TC_PORT_TYPEC ; +else if (is_tbt) + intel_dig_port->tc_type =TC_PORT_TBT ; +else +return ; + +/* Types are not supposed to be changed at runtime. */ +WARN_ON (old_type !=TC_PORT_UNKNOWN && + old_type != intel_dig_port->tc_type); + +if (old_type != intel_dig_port->tc_type) +DRM_DEBUG_KMS ("Port %c has TC type %s\n" ,port_name (port), +tc_type_name (intel_dig_port->tc_type)); +} + + +/* +* The type-C ports are different because even when they are connected, they may +* not be available/usable by the graphics driver: see the comment on +* icl_tc_phy_connect(). So in our driver instead of adding the additional +* concept of "usable" and make everything check for "connected and usable" we +* define a port as "connected" when it is not only connected, but also when it +* is usable by the rest of the driver. That maintains the old assumption that +* connected ports are usable, and avoids exposing to the users objects they +* can't really use. +*/ +bool intel_tc_port_connected (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum port port = dig_port->base.port; +enum tc_port tc_port =intel_port_to_tc (dev_priv, port); +bool is_legacy, is_typec, is_tbt; +u32 dpsp; + +/* +* Complain if we got a legacy port HPD, but VBT didn't mark the port as +* legacy. Treat the port as legacy from now on. +*/ +if (!dig_port->tc_legacy_port && +I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) { +DRM_ERROR ("VBT incorrectly claims port %c is not TypeC legacy\n" , +port_name (port)); + dig_port->tc_legacy_port = true; + } + is_legacy = dig_port->tc_legacy_port; + +/* +* The spec says we shouldn't be using the ISR bits for detecting +* between TC and TBT. We should use DFLEXDPSP. +*/ + dpsp =I915_READ (PORT_TX_DFLEXDPSP ); + is_typec = dpsp &TC_LIVE_STATE_TC (tc_port); + is_tbt = dpsp &TC_LIVE_STATE_TBT (tc_port); + +if (!is_legacy && !is_typec && !is_tbt) { +icl_tc_phy_disconnect (dig_port); + +return false; + } + +icl_update_tc_port_type (dev_priv, dig_port, is_legacy, is_typec, + is_tbt); + +if (!icl_tc_phy_connect (dig_port)) +return false; + +return true; +} +drivers/gpu/drm/i915/intel_tc.h new file +0
-0@@ -0,0 +1,13 @@SPDX header here please.
drivers/gpu/drm/i915/intel_tc.h line 8
Quoted 8 lines
drivers/gpu/drm/i915/intel_tc.h new file +8
-0+#ifndef __INTEL_TC_H__ +#define __INTEL_TC_H__ + +#include <linux/types.h> + +struct intel_digital_port ; + +void icl_tc_phy_disconnect (struct intel_digital_port *dig_port);I'd like to see this named intel_tc_* in the future.
BR,
Jani.Quoted 5 lines
drivers/gpu/drm/i915/intel_tc.h new file +5
-0+ +bool intel_tc_port_connected (struct intel_digital_port *dig_port); +int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port); + +#endif /* __INTEL_TC_H__ */
Signature · 5 lines
Jani Nikula, Intel Open Source Graphics Center _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 03/23] drm/i915: Move the TypeC port handling code to a separate file
In reply to Jani NikulaQuoted 377 lines · Jani Nikula
Quoted 6 lines · Imre Deak
Move the TypeC port handling functions to a new file for clarity.
While at it:
- s/icl_tc_port_connected()/intel_tc_port_connected()/icl_tc_phy_disconnect(), will be unexported later.Quoted 6 lines
- s/intel_dp_get_fia_supported_lane_count()/intel_tc_port_fia_max_lane_count()/ It's used for HDMI legacy mode too.
- Simplify function interfaces by passing only
dig_portto them.No functional changes.
Some nitpicks below.
BR,
Jani.Quoted 357 lines
Cc Animesh Manna <[email protected]>Cc Paulo Zanoni <[email protected]>Cc José Roberto de Souza <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/Makefile | 3 +- drivers/gpu/drm/i915/Makefile.header-test | 1 + drivers/gpu/drm/i915/intel_ddi.c | 6 +- drivers/gpu/drm/i915/intel_dp.c | 227 +-------------------- drivers/gpu/drm/i915/intel_dp.h | 2 - drivers/gpu/drm/i915/intel_tc.c | 230 ++++++++++++++++++++++ drivers/gpu/drm/i915/intel_tc.h | 13 ++ 7 files changed, 252 insertions(+), 230 deletions(-) create mode 100644 drivers/gpu/drm/i915/intel_tc.c create mode 100644 drivers/gpu/drm/i915/intel_tc.hdrivers/gpu/drm/i915/Makefile +2
-1@@ -171,7 +171,8 @@ i915-y += intel_audio.o \ intel_psr.o \ intel_quirks.o \ intel_sideband.o \ - intel_sprite.o + intel_sprite.o \ + intel_tc.o i915-$(CONFIG_ACPI) += intel_acpi.o intel_opregion.o i915-$(CONFIG_DRM_FBDEV_EMULATION) += intel_fbdev.odrivers/gpu/drm/i915/Makefile.header-test +1
-0@@ -58,6 +58,7 @@ header_test := \ intel_sdvo.h \ intel_sideband.h \ intel_sprite.h \ + intel_tc.h \ intel_tv.h \ intel_uncore.h \ intel_vdsc.h \drivers/gpu/drm/i915/intel_ddi.c +3
-3@@ -45,6 +45,7 @@#include "intel_lspcon.h" #include "intel_panel.h" #include "intel_psr.h" +#include "intel_tc.h" #include "intel_vdsc.h" struct ddi_buf_trans {@@ -3904,7 +3905,6 @@ static int intel_ddi_compute_config(struct intel_encoder *encoder,static void intel_ddi_encoder_suspend (struct intel_encoder *encoder) {struct intel_digital_port *dig_port =enc_to_dig_port (&encoder->base); -struct drm_i915_private *i915 =to_i915 (encoder->base.dev);intel_dp_encoder_suspend (encoder);@@ -3914,7 +3914,7 @@ static void intel_ddi_encoder_suspend(struct intel_encoder *encoder)* even if the sink has disappeared while being suspended. */ if (dig_port->tc_legacy_port) -icl_tc_phy_disconnect (i915, dig_port); +icl_tc_phy_disconnect (dig_port); }static void intel_ddi_encoder_reset (struct drm_encoder *drm_encoder)@@ -3936,7 +3936,7 @@ static void intel_ddi_encoder_destroy(struct drm_encoder *encoder)intel_dp_encoder_flush_work (encoder);if (intel_port_is_tc (i915, dig_port->base.port)) -icl_tc_phy_disconnect (i915, dig_port); +icl_tc_phy_disconnect (dig_port);drm_encoder_cleanup (encoder);kfree (dig_port);drivers/gpu/drm/i915/intel_dp.c +3
-224@@ -62,6 +62,7 @@#include "intel_panel.h" #include "intel_psr.h" #include "intel_sideband.h" +#include "intel_tc.h" #include "intel_vdsc.h" #define DP_DPRX_ESI_LEN 14@@ -211,46 +212,13 @@ static int intel_dp_max_common_rate(struct intel_dp *intel_dp)return intel_dp->common_rates[intel_dp->num_common_rates -1 ]; } -static int intel_dp_get_fia_supported_lane_count (struct intel_dp *intel_dp) -{ -struct intel_digital_port *dig_port =dp_to_dig_port (intel_dp); -struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); -enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); -intel_wakeref_t wakeref; -u32 lane_info; - -if (tc_port ==PORT_TC_NONE || dig_port->tc_type !=TC_PORT_TYPEC ) -return 4 ; - - lane_info =0 ; -with_intel_display_power (dev_priv,POWER_DOMAIN_DISPLAY_CORE , wakeref) - lane_info = (I915_READ(PORT_TX_DFLEXDPSP) & -DP_LANE_ASSIGNMENT_MASK (tc_port)) >> -DP_LANE_ASSIGNMENT_SHIFT (tc_port); - -switch (lane_info) { -default : -MISSING_CASE (lane_info); -case 1 : -case 2 : -case 4 : -case 8 : -return 1 ; -case 3 : -case 12 : -return 2 ; -case 15 : -return 4 ; - } -} -/* Theoretical max between source and sink */ static int intel_dp_max_common_lane_count (struct intel_dp *intel_dp) {struct intel_digital_port *intel_dig_port =dp_to_dig_port (intel_dp);int source_max = intel_dig_port->max_lanes;int sink_max =drm_dp_max_lane_count (intel_dp->dpcd); -int fia_max =intel_dp_get_fia_supported_lane_count (intel_dp); +int fia_max =intel_tc_port_fia_max_lane_count (intel_dig_port);return min3 (source_max, sink_max, fia_max); }@@ -5231,195 +5199,6 @@ static bool icl_combo_port_connected(struct drm_i915_private *dev_priv,return I915_READ (SDEISR ) &SDE_DDI_HOTPLUG_ICP (port); } -static const char *tc_type_name (enum tc_port_type type) -{ -static const char *const names[] = { - [TC_PORT_UNKNOWN ] ="unknown" , - [TC_PORT_LEGACY ] ="legacy" , - [TC_PORT_TYPEC ] ="typec" , - [TC_PORT_TBT ] ="tbt" , - }; - -if (WARN_ON (type >=ARRAY_SIZE (names))) - type =TC_PORT_UNKNOWN ; - -return names[type]; -} - -static void icl_update_tc_port_type (struct drm_i915_private *dev_priv, -struct intel_digital_port *intel_dig_port, -bool is_legacy,bool is_typec,bool is_tbt) -{ -enum port port = intel_dig_port->base.port; -enum tc_port_type old_type = intel_dig_port->tc_type; - -WARN_ON (is_legacy + is_typec + is_tbt !=1 ); - -if (is_legacy) - intel_dig_port->tc_type =TC_PORT_LEGACY ; -else if (is_typec) - intel_dig_port->tc_type =TC_PORT_TYPEC ; -else if (is_tbt) - intel_dig_port->tc_type =TC_PORT_TBT ; -else -return ; - -/* Types are not supposed to be changed at runtime. */ -WARN_ON (old_type !=TC_PORT_UNKNOWN && - old_type != intel_dig_port->tc_type); - -if (old_type != intel_dig_port->tc_type) -DRM_DEBUG_KMS ("Port %c has TC type %s\n" ,port_name (port), -tc_type_name (intel_dig_port->tc_type)); -} - -/* -* This function implements the first part of the Connect Flow described by our -* specification, Gen11 TypeC Programming chapter. The rest of the flow (reading -* lanes, EDID, etc) is done as needed in the typical places. -* -* Unlike the other ports, type-C ports are not available to use as soon as we -* get a hotplug. The type-C PHYs can be shared between multiple controllers: -* display, USB, etc. As a result, handshaking through FIA is required around -* connect and disconnect to cleanly transfer ownership with the controller and -* set the type-C power state. -* -* We could opt to only do the connect flow when we actually try to use the AUX -* channels or do a modeset, then immediately run the disconnect flow after -* usage, but there are some implications on this for a dynamic environment: -* things may go away or change behind our backs. So for now our driver is -* always trying to acquire ownership of the controller as soon as it gets an -* interrupt (or polls state and sees a port is connected) and only gives it -* back when it sees a disconnect. Implementation of a more fine-grained model -* will require a lot of coordination with user space and thorough testing for -* the extra possible cases. -*/ -static bool icl_tc_phy_connect (struct drm_i915_private *dev_priv, -struct intel_digital_port *dig_port) -{ -enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); -u32 val; - -if (dig_port->tc_type !=TC_PORT_LEGACY && - dig_port->tc_type !=TC_PORT_TYPEC ) -return true; - - val =I915_READ (PORT_TX_DFLEXDPPMS ); -if (!(val &DP_PHY_MODE_STATUS_COMPLETED (tc_port))) { -DRM_DEBUG_KMS ("DP PHY for TC port %d not ready\n" , tc_port); -WARN_ON (dig_port->tc_legacy_port); -return false; - } - -/* -* This function may be called many times in a row without an HPD event -* in between, so try to avoid the write when we can. -*/ - val =I915_READ (PORT_TX_DFLEXDPCSSS ); -if (!(val &DP_PHY_MODE_STATUS_NOT_SAFE (tc_port))) { - val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); -I915_WRITE (PORT_TX_DFLEXDPCSSS , val); - } - -/* -* Now we have to re-check the live state, in case the port recently -* became disconnected. Not necessary for legacy mode. -*/ -if (dig_port->tc_type ==TC_PORT_TYPEC && - !(I915_READ (PORT_TX_DFLEXDPSP ) &TC_LIVE_STATE_TC (tc_port))) { -DRM_DEBUG_KMS ("TC PHY %d sudden disconnect.\n" , tc_port); -icl_tc_phy_disconnect (dev_priv, dig_port); -return false; - } - -return true; -} - -/* -* See the comment at the connect function. This implements the Disconnect -* Flow. -*/ -void icl_tc_phy_disconnect (struct drm_i915_private *dev_priv, -struct intel_digital_port *dig_port) -{ -enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); - -if (dig_port->tc_type ==TC_PORT_UNKNOWN ) -return ; - -/* -* TBT disconnection flow is read the live status, what was done in -* caller. -*/ -if (dig_port->tc_type ==TC_PORT_TYPEC || - dig_port->tc_type ==TC_PORT_LEGACY ) { -u32 val; - - val =I915_READ (PORT_TX_DFLEXDPCSSS ); - val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); -I915_WRITE (PORT_TX_DFLEXDPCSSS , val); - } - -DRM_DEBUG_KMS ("Port %c TC type %s disconnected\n" , -port_name (dig_port->base.port), -tc_type_name (dig_port->tc_type)); - - dig_port->tc_type =TC_PORT_UNKNOWN ; -} - -/* -* The type-C ports are different because even when they are connected, they may -* not be available/usable by the graphics driver: see the comment on -* icl_tc_phy_connect(). So in our driver instead of adding the additional -* concept of "usable" and make everything check for "connected and usable" we -* define a port as "connected" when it is not only connected, but also when it -* is usable by the rest of the driver. That maintains the old assumption that -* connected ports are usable, and avoids exposing to the users objects they -* can't really use. -*/ -static bool icl_tc_port_connected (struct drm_i915_private *dev_priv, -struct intel_digital_port *intel_dig_port) -{ -enum port port = intel_dig_port->base.port; -enum tc_port tc_port =intel_port_to_tc (dev_priv, port); -bool is_legacy, is_typec, is_tbt; -u32 dpsp; - -/* -* Complain if we got a legacy port HPD, but VBT didn't mark the port as -* legacy. Treat the port as legacy from now on. -*/ -if (!intel_dig_port->tc_legacy_port && -I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) { -DRM_ERROR ("VBT incorrectly claims port %c is not TypeC legacy\n" , -port_name (port)); - intel_dig_port->tc_legacy_port = true; - } - is_legacy = intel_dig_port->tc_legacy_port; - -/* -* The spec says we shouldn't be using the ISR bits for detecting -* between TC and TBT. We should use DFLEXDPSP. -*/ - dpsp =I915_READ (PORT_TX_DFLEXDPSP ); - is_typec = dpsp &TC_LIVE_STATE_TC (tc_port); - is_tbt = dpsp &TC_LIVE_STATE_TBT (tc_port); - -if (!is_legacy && !is_typec && !is_tbt) { -icl_tc_phy_disconnect (dev_priv, intel_dig_port); - -return false; - } - -icl_update_tc_port_type (dev_priv, intel_dig_port, is_legacy, is_typec, - is_tbt); - -if (!icl_tc_phy_connect (dev_priv, intel_dig_port)) -return false; - -return true; -} -static bool icl_digital_port_connected (struct intel_encoder *encoder) {struct drm_i915_private *dev_priv =to_i915 (encoder->base.dev);@@ -5428,7 +5207,7 @@ static bool icl_digital_port_connected(struct intel_encoder *encoder)if (intel_port_is_combophy (dev_priv, encoder->port))return icl_combo_port_connected (dev_priv, dig_port);else if (intel_port_is_tc (dev_priv, encoder->port)) -return icl_tc_port_connected (dev_priv, dig_port); +return intel_tc_port_connected (dig_port);else MISSING_CASE (encoder->hpd_pin);drivers/gpu/drm/i915/intel_dp.h +0
-2@@ -112,8 +112,6 @@ bool intel_dp_get_colorimetry_status(struct intel_dp *intel_dp);int intel_dp_link_required (int pixel_clock,int bpp);int intel_dp_max_data_rate (int max_link_clock,int max_lanes);bool intel_digital_port_connected (struct intel_encoder *encoder); -void icl_tc_phy_disconnect (struct drm_i915_private *dev_priv, -struct intel_digital_port *dig_port);
Quoted 14 lines
drivers/gpu/drm/i915/intel_tc.c line 4
Quoted 12 lines
drivers/gpu/drm/i915/intel_dp.h +0
-0static inline unsigned int intel_dp_unused_lane_mask (int lane_count) {drivers/gpu/drm/i915/intel_tc.c new file +4
-0@@ -0,0 +1,230 @@ +// SPDX-License-Identifier: MIT +/* +* Copyright © 2019 Intel Corporation +*/ From the Nitpicks Department, please add a blank line here.
Ok.
Quoted 6 lines
drivers/gpu/drm/i915/intel_tc.c line 7
Quoted 4 lines
drivers/gpu/drm/i915/intel_tc.c new file +3
-0+#include "intel_display.h" +#include "i915_drv.h" +#include "intel_tc.h" And sort the includes.
Ok, forgot that here..
Quoted 224 lines
Quoted 224 lines
drivers/gpu/drm/i915/intel_tc.c new file +223
-0+ +static const char *tc_type_name (enum tc_port_type type) +{ +static const char *const names[] = { + [TC_PORT_UNKNOWN ] ="unknown" , + [TC_PORT_LEGACY ] ="legacy" , + [TC_PORT_TYPEC ] ="typec" , + [TC_PORT_TBT ] ="tbt" , + }; + +if (WARN_ON (type >=ARRAY_SIZE (names))) + type =TC_PORT_UNKNOWN ; + +return names[type]; +} + +int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +intel_wakeref_t wakeref; +u32 lane_info; + +if (tc_port ==PORT_TC_NONE || dig_port->tc_type !=TC_PORT_TYPEC ) +return 4 ; + + lane_info =0 ; +with_intel_display_power (dev_priv,POWER_DOMAIN_DISPLAY_CORE , wakeref) + lane_info = (I915_READ(PORT_TX_DFLEXDPSP) & +DP_LANE_ASSIGNMENT_MASK (tc_port)) >> +DP_LANE_ASSIGNMENT_SHIFT (tc_port); + +switch (lane_info) { +default : +MISSING_CASE (lane_info); +case 1 : +case 2 : +case 4 : +case 8 : +return 1 ; +case 3 : +case 12 : +return 2 ; +case 15 : +return 4 ; + } +} + +/* +* This function implements the first part of the Connect Flow described by our +* specification, Gen11 TypeC Programming chapter. The rest of the flow (reading +* lanes, EDID, etc) is done as needed in the typical places. +* +* Unlike the other ports, type-C ports are not available to use as soon as we +* get a hotplug. The type-C PHYs can be shared between multiple controllers: +* display, USB, etc. As a result, handshaking through FIA is required around +* connect and disconnect to cleanly transfer ownership with the controller and +* set the type-C power state. +* +* We could opt to only do the connect flow when we actually try to use the AUX +* channels or do a modeset, then immediately run the disconnect flow after +* usage, but there are some implications on this for a dynamic environment: +* things may go away or change behind our backs. So for now our driver is +* always trying to acquire ownership of the controller as soon as it gets an +* interrupt (or polls state and sees a port is connected) and only gives it +* back when it sees a disconnect. Implementation of a more fine-grained model +* will require a lot of coordination with user space and thorough testing for +* the extra possible cases. +*/ +static bool icl_tc_phy_connect (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +u32 val; + +if (dig_port->tc_type !=TC_PORT_LEGACY && + dig_port->tc_type !=TC_PORT_TYPEC ) +return true; + + val =I915_READ (PORT_TX_DFLEXDPPMS ); +if (!(val &DP_PHY_MODE_STATUS_COMPLETED (tc_port))) { +DRM_DEBUG_KMS ("DP PHY for TC port %d not ready\n" , tc_port); +WARN_ON (dig_port->tc_legacy_port); +return false; + } + +/* +* This function may be called many times in a row without an HPD event +* in between, so try to avoid the write when we can. +*/ + val =I915_READ (PORT_TX_DFLEXDPCSSS ); +if (!(val &DP_PHY_MODE_STATUS_NOT_SAFE (tc_port))) { + val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); +I915_WRITE (PORT_TX_DFLEXDPCSSS , val); + } + +/* +* Now we have to re-check the live state, in case the port recently +* became disconnected. Not necessary for legacy mode. +*/ +if (dig_port->tc_type ==TC_PORT_TYPEC && + !(I915_READ (PORT_TX_DFLEXDPSP ) &TC_LIVE_STATE_TC (tc_port))) { +DRM_DEBUG_KMS ("TC PHY %d sudden disconnect.\n" , tc_port); +icl_tc_phy_disconnect (dig_port); +return false; + } + +return true; +} + +/* +* See the comment at the connect function. This implements the Disconnect +* Flow. +*/ +void icl_tc_phy_disconnect (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); + +if (dig_port->tc_type ==TC_PORT_UNKNOWN ) +return ; + +/* +* TBT disconnection flow is read the live status, what was done in +* caller. +*/ +if (dig_port->tc_type ==TC_PORT_TYPEC || + dig_port->tc_type ==TC_PORT_LEGACY ) { +u32 val; + + val =I915_READ (PORT_TX_DFLEXDPCSSS ); + val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); +I915_WRITE (PORT_TX_DFLEXDPCSSS , val); + } + +DRM_DEBUG_KMS ("Port %c TC type %s disconnected\n" , +port_name (dig_port->base.port), +tc_type_name (dig_port->tc_type)); + + dig_port->tc_type =TC_PORT_UNKNOWN ; +} + +static void icl_update_tc_port_type (struct drm_i915_private *dev_priv, +struct intel_digital_port *intel_dig_port, +bool is_legacy,bool is_typec,bool is_tbt) +{ +enum port port = intel_dig_port->base.port; +enum tc_port_type old_type = intel_dig_port->tc_type; + +WARN_ON (is_legacy + is_typec + is_tbt !=1 ); + +if (is_legacy) + intel_dig_port->tc_type =TC_PORT_LEGACY ; +else if (is_typec) + intel_dig_port->tc_type =TC_PORT_TYPEC ; +else if (is_tbt) + intel_dig_port->tc_type =TC_PORT_TBT ; +else +return ; + +/* Types are not supposed to be changed at runtime. */ +WARN_ON (old_type !=TC_PORT_UNKNOWN && + old_type != intel_dig_port->tc_type); + +if (old_type != intel_dig_port->tc_type) +DRM_DEBUG_KMS ("Port %c has TC type %s\n" ,port_name (port), +tc_type_name (intel_dig_port->tc_type)); +} + + +/* +* The type-C ports are different because even when they are connected, they may +* not be available/usable by the graphics driver: see the comment on +* icl_tc_phy_connect(). So in our driver instead of adding the additional +* concept of "usable" and make everything check for "connected and usable" we +* define a port as "connected" when it is not only connected, but also when it +* is usable by the rest of the driver. That maintains the old assumption that +* connected ports are usable, and avoids exposing to the users objects they +* can't really use. +*/ +bool intel_tc_port_connected (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum port port = dig_port->base.port; +enum tc_port tc_port =intel_port_to_tc (dev_priv, port); +bool is_legacy, is_typec, is_tbt; +u32 dpsp; + +/* +* Complain if we got a legacy port HPD, but VBT didn't mark the port as +* legacy. Treat the port as legacy from now on. +*/ +if (!dig_port->tc_legacy_port && +I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) { +DRM_ERROR ("VBT incorrectly claims port %c is not TypeC legacy\n" , +port_name (port)); + dig_port->tc_legacy_port = true; + } + is_legacy = dig_port->tc_legacy_port; + +/* +* The spec says we shouldn't be using the ISR bits for detecting +* between TC and TBT. We should use DFLEXDPSP. +*/ + dpsp =I915_READ (PORT_TX_DFLEXDPSP ); + is_typec = dpsp &TC_LIVE_STATE_TC (tc_port); + is_tbt = dpsp &TC_LIVE_STATE_TBT (tc_port); + +if (!is_legacy && !is_typec && !is_tbt) { +icl_tc_phy_disconnect (dig_port); + +return false; + } + +icl_update_tc_port_type (dev_priv, dig_port, is_legacy, is_typec, + is_tbt); + +if (!icl_tc_phy_connect (dig_port)) +return false; + +return true; +} +
Quoted 8 lines
drivers/gpu/drm/i915/intel_tc.h
Quoted 6 lines
drivers/gpu/drm/i915/intel_tc.h new file +0
-0@@ -0,0 +1,13 @@SPDX header here please.
Ok, added that like:
https://github.com/ideak/linux/blob/2dee09f687ba/drivers/gpu/drm/i915/intel_tc.h#L2
Quoted 11 lines
drivers/gpu/drm/i915/intel_tc.h line 8
Quoted 9 lines
drivers/gpu/drm/i915/intel_tc.h new file +8
-0+#ifndef __INTEL_TC_H__ +#define __INTEL_TC_H__ + +#include <linux/types.h> + +struct intel_digital_port ; + +void icl_tc_phy_disconnect (struct intel_digital_port *dig_port);I'd like to see this named intel_tc_* in the future.
Yep, thought about that rule, which is good, but I kept this one as-is, since later in this patchset it will get unexported.
Quoted 5 lines
BR,
Jani.
Quoted 8 lines
Quoted 5 lines
drivers/gpu/drm/i915/intel_tc.h new file +5
-0+ +bool intel_tc_port_connected (struct intel_digital_port *dig_port); +int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port); + +#endif /* __INTEL_TC_H__ */ Signature · 1 line
Jani Nikula, Intel Open Source Graphics Center
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 03/23] drm/i915: Move the TypeC port handling code to a separate file
In reply to Jani NikulaQuoted 392 lines · Jani Nikula
Quoted 6 lines · Imre Deak
Move the TypeC port handling functions to a new file for clarity.
While at it:
- s/icl_tc_port_connected()/intel_tc_port_connected()/icl_tc_phy_disconnect(), will be unexported later.Quoted 6 lines
- s/intel_dp_get_fia_supported_lane_count()/intel_tc_port_fia_max_lane_count()/ It's used for HDMI legacy mode too.
- Simplify function interfaces by passing only
dig_portto them.No functional changes.
Some nitpicks below.
BR,
Jani.Quoted 365 lines
Cc Animesh Manna <[email protected]>Cc Paulo Zanoni <[email protected]>Cc José Roberto de Souza <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/Makefile | 3 +- drivers/gpu/drm/i915/Makefile.header-test | 1 + drivers/gpu/drm/i915/intel_ddi.c | 6 +- drivers/gpu/drm/i915/intel_dp.c | 227 +-------------------- drivers/gpu/drm/i915/intel_dp.h | 2 - drivers/gpu/drm/i915/intel_tc.c | 230 ++++++++++++++++++++++ drivers/gpu/drm/i915/intel_tc.h | 13 ++ 7 files changed, 252 insertions(+), 230 deletions(-) create mode 100644 drivers/gpu/drm/i915/intel_tc.c create mode 100644 drivers/gpu/drm/i915/intel_tc.hdrivers/gpu/drm/i915/Makefile +2
-1@@ -171,7 +171,8 @@ i915-y += intel_audio.o \ intel_psr.o \ intel_quirks.o \ intel_sideband.o \ - intel_sprite.o + intel_sprite.o \ + intel_tc.o i915-$(CONFIG_ACPI) += intel_acpi.o intel_opregion.o i915-$(CONFIG_DRM_FBDEV_EMULATION) += intel_fbdev.odrivers/gpu/drm/i915/Makefile.header-test +1
-0@@ -58,6 +58,7 @@ header_test := \ intel_sdvo.h \ intel_sideband.h \ intel_sprite.h \ + intel_tc.h \ intel_tv.h \ intel_uncore.h \ intel_vdsc.h \drivers/gpu/drm/i915/intel_ddi.c +3
-3@@ -45,6 +45,7 @@#include "intel_lspcon.h" #include "intel_panel.h" #include "intel_psr.h" +#include "intel_tc.h" #include "intel_vdsc.h" struct ddi_buf_trans {@@ -3904,7 +3905,6 @@ static int intel_ddi_compute_config(struct intel_encoder *encoder,static void intel_ddi_encoder_suspend (struct intel_encoder *encoder) {struct intel_digital_port *dig_port =enc_to_dig_port (&encoder->base); -struct drm_i915_private *i915 =to_i915 (encoder->base.dev);intel_dp_encoder_suspend (encoder);@@ -3914,7 +3914,7 @@ static void intel_ddi_encoder_suspend(struct intel_encoder *encoder)* even if the sink has disappeared while being suspended. */ if (dig_port->tc_legacy_port) -icl_tc_phy_disconnect (i915, dig_port); +icl_tc_phy_disconnect (dig_port); }static void intel_ddi_encoder_reset (struct drm_encoder *drm_encoder)@@ -3936,7 +3936,7 @@ static void intel_ddi_encoder_destroy(struct drm_encoder *encoder)intel_dp_encoder_flush_work (encoder);if (intel_port_is_tc (i915, dig_port->base.port)) -icl_tc_phy_disconnect (i915, dig_port); +icl_tc_phy_disconnect (dig_port);drm_encoder_cleanup (encoder);kfree (dig_port);drivers/gpu/drm/i915/intel_dp.c +3
-224@@ -62,6 +62,7 @@#include "intel_panel.h" #include "intel_psr.h" #include "intel_sideband.h" +#include "intel_tc.h" #include "intel_vdsc.h" #define DP_DPRX_ESI_LEN 14@@ -211,46 +212,13 @@ static int intel_dp_max_common_rate(struct intel_dp *intel_dp)return intel_dp->common_rates[intel_dp->num_common_rates -1 ]; } -static int intel_dp_get_fia_supported_lane_count (struct intel_dp *intel_dp) -{ -struct intel_digital_port *dig_port =dp_to_dig_port (intel_dp); -struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); -enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); -intel_wakeref_t wakeref; -u32 lane_info; - -if (tc_port ==PORT_TC_NONE || dig_port->tc_type !=TC_PORT_TYPEC ) -return 4 ; - - lane_info =0 ; -with_intel_display_power (dev_priv,POWER_DOMAIN_DISPLAY_CORE , wakeref) - lane_info = (I915_READ(PORT_TX_DFLEXDPSP) & -DP_LANE_ASSIGNMENT_MASK (tc_port)) >> -DP_LANE_ASSIGNMENT_SHIFT (tc_port); - -switch (lane_info) { -default : -MISSING_CASE (lane_info); -case 1 : -case 2 : -case 4 : -case 8 : -return 1 ; -case 3 : -case 12 : -return 2 ; -case 15 : -return 4 ; - } -} -/* Theoretical max between source and sink */ static int intel_dp_max_common_lane_count (struct intel_dp *intel_dp) {struct intel_digital_port *intel_dig_port =dp_to_dig_port (intel_dp);int source_max = intel_dig_port->max_lanes;int sink_max =drm_dp_max_lane_count (intel_dp->dpcd); -int fia_max =intel_dp_get_fia_supported_lane_count (intel_dp); +int fia_max =intel_tc_port_fia_max_lane_count (intel_dig_port);return min3 (source_max, sink_max, fia_max); }@@ -5231,195 +5199,6 @@ static bool icl_combo_port_connected(struct drm_i915_private *dev_priv,return I915_READ (SDEISR ) &SDE_DDI_HOTPLUG_ICP (port); } -static const char *tc_type_name (enum tc_port_type type) -{ -static const char *const names[] = { - [TC_PORT_UNKNOWN ] ="unknown" , - [TC_PORT_LEGACY ] ="legacy" , - [TC_PORT_TYPEC ] ="typec" , - [TC_PORT_TBT ] ="tbt" , - }; - -if (WARN_ON (type >=ARRAY_SIZE (names))) - type =TC_PORT_UNKNOWN ; - -return names[type]; -} - -static void icl_update_tc_port_type (struct drm_i915_private *dev_priv, -struct intel_digital_port *intel_dig_port, -bool is_legacy,bool is_typec,bool is_tbt) -{ -enum port port = intel_dig_port->base.port; -enum tc_port_type old_type = intel_dig_port->tc_type; - -WARN_ON (is_legacy + is_typec + is_tbt !=1 ); - -if (is_legacy) - intel_dig_port->tc_type =TC_PORT_LEGACY ; -else if (is_typec) - intel_dig_port->tc_type =TC_PORT_TYPEC ; -else if (is_tbt) - intel_dig_port->tc_type =TC_PORT_TBT ; -else -return ; - -/* Types are not supposed to be changed at runtime. */ -WARN_ON (old_type !=TC_PORT_UNKNOWN && - old_type != intel_dig_port->tc_type); - -if (old_type != intel_dig_port->tc_type) -DRM_DEBUG_KMS ("Port %c has TC type %s\n" ,port_name (port), -tc_type_name (intel_dig_port->tc_type)); -} - -/* -* This function implements the first part of the Connect Flow described by our -* specification, Gen11 TypeC Programming chapter. The rest of the flow (reading -* lanes, EDID, etc) is done as needed in the typical places. -* -* Unlike the other ports, type-C ports are not available to use as soon as we -* get a hotplug. The type-C PHYs can be shared between multiple controllers: -* display, USB, etc. As a result, handshaking through FIA is required around -* connect and disconnect to cleanly transfer ownership with the controller and -* set the type-C power state. -* -* We could opt to only do the connect flow when we actually try to use the AUX -* channels or do a modeset, then immediately run the disconnect flow after -* usage, but there are some implications on this for a dynamic environment: -* things may go away or change behind our backs. So for now our driver is -* always trying to acquire ownership of the controller as soon as it gets an -* interrupt (or polls state and sees a port is connected) and only gives it -* back when it sees a disconnect. Implementation of a more fine-grained model -* will require a lot of coordination with user space and thorough testing for -* the extra possible cases. -*/ -static bool icl_tc_phy_connect (struct drm_i915_private *dev_priv, -struct intel_digital_port *dig_port) -{ -enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); -u32 val; - -if (dig_port->tc_type !=TC_PORT_LEGACY && - dig_port->tc_type !=TC_PORT_TYPEC ) -return true; - - val =I915_READ (PORT_TX_DFLEXDPPMS ); -if (!(val &DP_PHY_MODE_STATUS_COMPLETED (tc_port))) { -DRM_DEBUG_KMS ("DP PHY for TC port %d not ready\n" , tc_port); -WARN_ON (dig_port->tc_legacy_port); -return false; - } - -/* -* This function may be called many times in a row without an HPD event -* in between, so try to avoid the write when we can. -*/ - val =I915_READ (PORT_TX_DFLEXDPCSSS ); -if (!(val &DP_PHY_MODE_STATUS_NOT_SAFE (tc_port))) { - val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); -I915_WRITE (PORT_TX_DFLEXDPCSSS , val); - } - -/* -* Now we have to re-check the live state, in case the port recently -* became disconnected. Not necessary for legacy mode. -*/ -if (dig_port->tc_type ==TC_PORT_TYPEC && - !(I915_READ (PORT_TX_DFLEXDPSP ) &TC_LIVE_STATE_TC (tc_port))) { -DRM_DEBUG_KMS ("TC PHY %d sudden disconnect.\n" , tc_port); -icl_tc_phy_disconnect (dev_priv, dig_port); -return false; - } - -return true; -} - -/* -* See the comment at the connect function. This implements the Disconnect -* Flow. -*/ -void icl_tc_phy_disconnect (struct drm_i915_private *dev_priv, -struct intel_digital_port *dig_port) -{ -enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); - -if (dig_port->tc_type ==TC_PORT_UNKNOWN ) -return ; - -/* -* TBT disconnection flow is read the live status, what was done in -* caller. -*/ -if (dig_port->tc_type ==TC_PORT_TYPEC || - dig_port->tc_type ==TC_PORT_LEGACY ) { -u32 val; - - val =I915_READ (PORT_TX_DFLEXDPCSSS ); - val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); -I915_WRITE (PORT_TX_DFLEXDPCSSS , val); - } - -DRM_DEBUG_KMS ("Port %c TC type %s disconnected\n" , -port_name (dig_port->base.port), -tc_type_name (dig_port->tc_type)); - - dig_port->tc_type =TC_PORT_UNKNOWN ; -} - -/* -* The type-C ports are different because even when they are connected, they may -* not be available/usable by the graphics driver: see the comment on -* icl_tc_phy_connect(). So in our driver instead of adding the additional -* concept of "usable" and make everything check for "connected and usable" we -* define a port as "connected" when it is not only connected, but also when it -* is usable by the rest of the driver. That maintains the old assumption that -* connected ports are usable, and avoids exposing to the users objects they -* can't really use. -*/ -static bool icl_tc_port_connected (struct drm_i915_private *dev_priv, -struct intel_digital_port *intel_dig_port) -{ -enum port port = intel_dig_port->base.port; -enum tc_port tc_port =intel_port_to_tc (dev_priv, port); -bool is_legacy, is_typec, is_tbt; -u32 dpsp; - -/* -* Complain if we got a legacy port HPD, but VBT didn't mark the port as -* legacy. Treat the port as legacy from now on. -*/ -if (!intel_dig_port->tc_legacy_port && -I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) { -DRM_ERROR ("VBT incorrectly claims port %c is not TypeC legacy\n" , -port_name (port)); - intel_dig_port->tc_legacy_port = true; - } - is_legacy = intel_dig_port->tc_legacy_port; - -/* -* The spec says we shouldn't be using the ISR bits for detecting -* between TC and TBT. We should use DFLEXDPSP. -*/ - dpsp =I915_READ (PORT_TX_DFLEXDPSP ); - is_typec = dpsp &TC_LIVE_STATE_TC (tc_port); - is_tbt = dpsp &TC_LIVE_STATE_TBT (tc_port); - -if (!is_legacy && !is_typec && !is_tbt) { -icl_tc_phy_disconnect (dev_priv, intel_dig_port); - -return false; - } - -icl_update_tc_port_type (dev_priv, intel_dig_port, is_legacy, is_typec, - is_tbt); - -if (!icl_tc_phy_connect (dev_priv, intel_dig_port)) -return false; - -return true; -} -static bool icl_digital_port_connected (struct intel_encoder *encoder) {struct drm_i915_private *dev_priv =to_i915 (encoder->base.dev);@@ -5428,7 +5207,7 @@ static bool icl_digital_port_connected(struct intel_encoder *encoder)if (intel_port_is_combophy (dev_priv, encoder->port))return icl_combo_port_connected (dev_priv, dig_port);else if (intel_port_is_tc (dev_priv, encoder->port)) -return icl_tc_port_connected (dev_priv, dig_port); +return intel_tc_port_connected (dig_port);else MISSING_CASE (encoder->hpd_pin);drivers/gpu/drm/i915/intel_dp.h +0
-2@@ -112,8 +112,6 @@ bool intel_dp_get_colorimetry_status(struct intel_dp *intel_dp);int intel_dp_link_required (int pixel_clock,int bpp);int intel_dp_max_data_rate (int max_link_clock,int max_lanes);bool intel_digital_port_connected (struct intel_encoder *encoder); -void icl_tc_phy_disconnect (struct drm_i915_private *dev_priv, -struct intel_digital_port *dig_port);static inline unsigned int intel_dp_unused_lane_mask (int lane_count) {drivers/gpu/drm/i915/intel_tc.c new file +0
-0drivers/gpu/drm/i915/intel_tc.c line 4
Quoted 4 lines
drivers/gpu/drm/i915/intel_tc.c new file +4
-0@@ -0,0 +1,230 @@ +// SPDX-License-Identifier: MIT +/* +* Copyright © 2019 Intel Corporation +*/ From the Nitpicks Department, please add a blank line here.
Quoted 5 lines
drivers/gpu/drm/i915/intel_tc.c line 7
Quoted 3 lines
drivers/gpu/drm/i915/intel_tc.c new file +3
-0+#include "intel_display.h" +#include "i915_drv.h" +#include "intel_tc.h" And sort the includes.
humn... In some other projects I use the convention of always having the correspondent header to be included first and the rest sorted. Here it would be like:
#include "intel_tc.h"
#include "intel_display.h"
#include "intel_drv.h"
This way we guarantee that intel_tc.h header is self-contained: anything it needs, it includes or declares. If we adopted such convention I don't see why we would still need Makefile.header-test for example.
Lucas De Marchi
Quoted 248 lines
drivers/gpu/drm/i915/intel_tc.h
Quoted 230 lines
drivers/gpu/drm/i915/intel_tc.c new file +223
-0+ +static const char *tc_type_name (enum tc_port_type type) +{ +static const char *const names[] = { + [TC_PORT_UNKNOWN ] ="unknown" , + [TC_PORT_LEGACY ] ="legacy" , + [TC_PORT_TYPEC ] ="typec" , + [TC_PORT_TBT ] ="tbt" , + }; + +if (WARN_ON (type >=ARRAY_SIZE (names))) + type =TC_PORT_UNKNOWN ; + +return names[type]; +} + +int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +intel_wakeref_t wakeref; +u32 lane_info; + +if (tc_port ==PORT_TC_NONE || dig_port->tc_type !=TC_PORT_TYPEC ) +return 4 ; + + lane_info =0 ; +with_intel_display_power (dev_priv,POWER_DOMAIN_DISPLAY_CORE , wakeref) + lane_info = (I915_READ(PORT_TX_DFLEXDPSP) & +DP_LANE_ASSIGNMENT_MASK (tc_port)) >> +DP_LANE_ASSIGNMENT_SHIFT (tc_port); + +switch (lane_info) { +default : +MISSING_CASE (lane_info); +case 1 : +case 2 : +case 4 : +case 8 : +return 1 ; +case 3 : +case 12 : +return 2 ; +case 15 : +return 4 ; + } +} + +/* +* This function implements the first part of the Connect Flow described by our +* specification, Gen11 TypeC Programming chapter. The rest of the flow (reading +* lanes, EDID, etc) is done as needed in the typical places. +* +* Unlike the other ports, type-C ports are not available to use as soon as we +* get a hotplug. The type-C PHYs can be shared between multiple controllers: +* display, USB, etc. As a result, handshaking through FIA is required around +* connect and disconnect to cleanly transfer ownership with the controller and +* set the type-C power state. +* +* We could opt to only do the connect flow when we actually try to use the AUX +* channels or do a modeset, then immediately run the disconnect flow after +* usage, but there are some implications on this for a dynamic environment: +* things may go away or change behind our backs. So for now our driver is +* always trying to acquire ownership of the controller as soon as it gets an +* interrupt (or polls state and sees a port is connected) and only gives it +* back when it sees a disconnect. Implementation of a more fine-grained model +* will require a lot of coordination with user space and thorough testing for +* the extra possible cases. +*/ +static bool icl_tc_phy_connect (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +u32 val; + +if (dig_port->tc_type !=TC_PORT_LEGACY && + dig_port->tc_type !=TC_PORT_TYPEC ) +return true; + + val =I915_READ (PORT_TX_DFLEXDPPMS ); +if (!(val &DP_PHY_MODE_STATUS_COMPLETED (tc_port))) { +DRM_DEBUG_KMS ("DP PHY for TC port %d not ready\n" , tc_port); +WARN_ON (dig_port->tc_legacy_port); +return false; + } + +/* +* This function may be called many times in a row without an HPD event +* in between, so try to avoid the write when we can. +*/ + val =I915_READ (PORT_TX_DFLEXDPCSSS ); +if (!(val &DP_PHY_MODE_STATUS_NOT_SAFE (tc_port))) { + val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); +I915_WRITE (PORT_TX_DFLEXDPCSSS , val); + } + +/* +* Now we have to re-check the live state, in case the port recently +* became disconnected. Not necessary for legacy mode. +*/ +if (dig_port->tc_type ==TC_PORT_TYPEC && + !(I915_READ (PORT_TX_DFLEXDPSP ) &TC_LIVE_STATE_TC (tc_port))) { +DRM_DEBUG_KMS ("TC PHY %d sudden disconnect.\n" , tc_port); +icl_tc_phy_disconnect (dig_port); +return false; + } + +return true; +} + +/* +* See the comment at the connect function. This implements the Disconnect +* Flow. +*/ +void icl_tc_phy_disconnect (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); + +if (dig_port->tc_type ==TC_PORT_UNKNOWN ) +return ; + +/* +* TBT disconnection flow is read the live status, what was done in +* caller. +*/ +if (dig_port->tc_type ==TC_PORT_TYPEC || + dig_port->tc_type ==TC_PORT_LEGACY ) { +u32 val; + + val =I915_READ (PORT_TX_DFLEXDPCSSS ); + val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); +I915_WRITE (PORT_TX_DFLEXDPCSSS , val); + } + +DRM_DEBUG_KMS ("Port %c TC type %s disconnected\n" , +port_name (dig_port->base.port), +tc_type_name (dig_port->tc_type)); + + dig_port->tc_type =TC_PORT_UNKNOWN ; +} + +static void icl_update_tc_port_type (struct drm_i915_private *dev_priv, +struct intel_digital_port *intel_dig_port, +bool is_legacy,bool is_typec,bool is_tbt) +{ +enum port port = intel_dig_port->base.port; +enum tc_port_type old_type = intel_dig_port->tc_type; + +WARN_ON (is_legacy + is_typec + is_tbt !=1 ); + +if (is_legacy) + intel_dig_port->tc_type =TC_PORT_LEGACY ; +else if (is_typec) + intel_dig_port->tc_type =TC_PORT_TYPEC ; +else if (is_tbt) + intel_dig_port->tc_type =TC_PORT_TBT ; +else +return ; + +/* Types are not supposed to be changed at runtime. */ +WARN_ON (old_type !=TC_PORT_UNKNOWN && + old_type != intel_dig_port->tc_type); + +if (old_type != intel_dig_port->tc_type) +DRM_DEBUG_KMS ("Port %c has TC type %s\n" ,port_name (port), +tc_type_name (intel_dig_port->tc_type)); +} + + +/* +* The type-C ports are different because even when they are connected, they may +* not be available/usable by the graphics driver: see the comment on +* icl_tc_phy_connect(). So in our driver instead of adding the additional +* concept of "usable" and make everything check for "connected and usable" we +* define a port as "connected" when it is not only connected, but also when it +* is usable by the rest of the driver. That maintains the old assumption that +* connected ports are usable, and avoids exposing to the users objects they +* can't really use. +*/ +bool intel_tc_port_connected (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum port port = dig_port->base.port; +enum tc_port tc_port =intel_port_to_tc (dev_priv, port); +bool is_legacy, is_typec, is_tbt; +u32 dpsp; + +/* +* Complain if we got a legacy port HPD, but VBT didn't mark the port as +* legacy. Treat the port as legacy from now on. +*/ +if (!dig_port->tc_legacy_port && +I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) { +DRM_ERROR ("VBT incorrectly claims port %c is not TypeC legacy\n" , +port_name (port)); + dig_port->tc_legacy_port = true; + } + is_legacy = dig_port->tc_legacy_port; + +/* +* The spec says we shouldn't be using the ISR bits for detecting +* between TC and TBT. We should use DFLEXDPSP. +*/ + dpsp =I915_READ (PORT_TX_DFLEXDPSP ); + is_typec = dpsp &TC_LIVE_STATE_TC (tc_port); + is_tbt = dpsp &TC_LIVE_STATE_TBT (tc_port); + +if (!is_legacy && !is_typec && !is_tbt) { +icl_tc_phy_disconnect (dig_port); + +return false; + } + +icl_update_tc_port_type (dev_priv, dig_port, is_legacy, is_typec, + is_tbt); + +if (!icl_tc_phy_connect (dig_port)) +return false; + +return true; +} +drivers/gpu/drm/i915/intel_tc.h new file +0
-0@@ -0,0 +1,13 @@SPDX header here please.
drivers/gpu/drm/i915/intel_tc.h line 8
Quoted 8 lines
drivers/gpu/drm/i915/intel_tc.h new file +8
-0+#ifndef __INTEL_TC_H__ +#define __INTEL_TC_H__ + +#include <linux/types.h> + +struct intel_digital_port ; + +void icl_tc_phy_disconnect (struct intel_digital_port *dig_port);I'd like to see this named intel_tc_* in the future.
BR,
Jani.
Quoted 12 lines
Quoted 5 lines
drivers/gpu/drm/i915/intel_tc.h new file +5
-0+ +bool intel_tc_port_connected (struct intel_digital_port *dig_port); +int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port); + +#endif /* __INTEL_TC_H__ */ Signature · 5 lines
Jani Nikula, Intel Open Source Graphics Center _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Jani Nikula
maintainerRe: [PATCH 03/23] drm/i915: Move the TypeC port handling code to a separate file
Quoted 14 lines · Lucas De Marchi
Quoted 8 lines · Jani Nikula
On Tue, 04 Jun 2019, Imre Deak <[email protected]> wrote:
From the Nitpicks Department, please add a blank line here.drivers/gpu/drm/i915/intel_tc.c line 7
Quoted 3 lines
drivers/gpu/drm/i915/intel_tc.c new file +3
-0+#include "intel_display.h" +#include "i915_drv.h" +#include "intel_tc.h" And sort the includes.
humn... In some other projects I use the convention of always having the correspondent header to be included first and the rest sorted. Here it would be like:
Quoted 8 lines
#include "
intel_tc.h"#include "
intel_display.h"
#include "intel_drv.h"This way we guarantee that
intel_tc.hheader is self-contained: anything it needs, it includes or declares. If we adopted such convention I don't see why we would still need Makefile.header-test for example.
I think the long standing convention is to have <asm>, <linux>, and <drm> headers included before "local" headers.
Eventually the version of header tests that I've submitted to kbuild upstream will obsolete the Makefile.header-test files, and I expect us to have simply
header-test-y := $(notdir $(wildcard $(src)/*.h))
in there, testing everything.
BR,
Jani.
Signature · 5 lines
Jani Nikula, Intel Open Source Graphics Center _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 03/23] drm/i915: Move the TypeC port handling code to a separate file
In reply to Imre DeakQuoted 6 lines · Imre Deak
Move the TypeC port handling functions to a new file for clarity.
While at it:
- s/icl_tc_port_connected()/intel_tc_port_connected()/icl_tc_phy_disconnect(), will be unexported later.
Quoted 8 lines
- s/intel_dp_get_fia_supported_lane_count()/intel_tc_port_fia_max_lane_ count()/
It's used for HDMI legacy mode too.- Simplify function interfaces by passing only
dig_portto them.No functional changes.
Nice.
Quoted 722 lines
Cc Animesh Manna <[email protected]>Cc Paulo Zanoni <[email protected]>Cc José Roberto de Souza <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/Makefile | 3 +- drivers/gpu/drm/i915/Makefile.header-test | 1 + drivers/gpu/drm/i915/intel_ddi.c | 6 +- drivers/gpu/drm/i915/intel_dp.c | 227 +-------------------(quoted diff) +1
-1- drivers/gpu/drm/i915/intel_dp.h | 2 - drivers/gpu/drm/i915/intel_tc.c | 230 ++++++++++++++++++++++ drivers/gpu/drm/i915/intel_tc.h | 13 ++ 7 files changed, 252 insertions(+), 230 deletions(-) create mode 100644 drivers/gpu/drm/i915/intel_tc.c create mode 100644 drivers/gpu/drm/i915/intel_tc.hdrivers/gpu/drm/i915/Makefile +2
-1@@ -171,7 +171,8 @@ i915-y += intel_audio.o \ intel_psr.o \ intel_quirks.o \ intel_sideband.o \ - intel_sprite.o + intel_sprite.o \ + intel_tc.o i915-$(CONFIG_ACPI) += intel_acpi.o intel_opregion.o i915-$(CONFIG_DRM_FBDEV_EMULATION) += intel_fbdev.odrivers/gpu/drm/i915/Makefile.header-test +1
-0@@ -58,6 +58,7 @@ header_test := \ intel_sdvo.h \ intel_sideband.h \ intel_sprite.h \ + intel_tc.h \ intel_tv.h \ intel_uncore.h \ intel_vdsc.h \drivers/gpu/drm/i915/intel_ddi.c +1
-1@@ -45,6 +45,7 @@#include "intel_lspcon.h" #include "intel_panel.h" #include "intel_psr.h" +#include "intel_tc.h" #include "intel_vdsc.h" struct ddi_buf_trans {@@ -3904,7 +3905,6 @@ static int intel_ddi_compute_config(structintel_encoder *encoder, static void intel_ddi_encoder_suspend(struct intel_encoder *encoder) { struct intel_digital_port *dig_port = enc_to_dig_port(&encoder- >base); -struct drm_i915_private *i915 =to_i915 (encoder->base.dev);drivers/gpu/drm/i915/intel_ddi.c +1
-1intel_dp_encoder_suspend (encoder);@@ -3914,7 +3914,7 @@ static void intel_ddi_encoder_suspend(structintel_encoder *encoder) * even if the sink has disappeared while being suspended. */ if (dig_port->tc_legacy_port) -icl_tc_phy_disconnect (i915, dig_port); +icl_tc_phy_disconnect (dig_port); }static void
intel_ddi_encoder_reset(struct drm_encoder *drm_encoder)drivers/gpu/drm/i915/intel_ddi.c +1
-1@@ -3936,7 +3936,7 @@ static void intel_ddi_encoder_destroy(struct drm_encoder *encoder)intel_dp_encoder_flush_work (encoder );if (intel_port_is_tc (i915, dig_port->base.port)) -icl_tc_phy_disconnect (i915, dig_port); +icl_tc_phy_disconnect (dig_port);drm_encoder_cleanup (encoder);drivers/gpu/drm/i915/intel_ddi.c +0
-0kfree (dig_port);drivers/gpu/drm/i915/intel_dp.c +1
-33@@ -62,6 +62,7 @@#include "intel_panel.h" #include "intel_psr.h" #include "intel_sideband.h" +#include "intel_tc.h" #include "intel_vdsc.h" #define DP_DPRX_ESI_LEN 14@@ -211,46 +212,13 @@ static int intel_dp_max_common_rate(struct intel_dp *intel_dp)return intel_dp->common_rates[intel_dp->num_common_rates -1 ]; } -static int intel_dp_get_fia_supported_lane_count (struct intel_dp *intel_dp) -{ -struct intel_digital_port *dig_port =dp_to_dig_port (intel_dp); -struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev); -enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port- >base.port); -intel_wakeref_t wakeref; -u32 lane_info; - -if (tc_port ==PORT_TC_NONE || dig_port->tc_type != TC_PORT_TYPEC) -return 4 ; - - lane_info =0 ; -with_intel_display_power (dev_priv,POWER_DOMAIN_DISPLAY_CORE , wakeref) - lane_info = (I915_READ(PORT_TX_DFLEXDPSP) & -DP_LANE_ASSIGNMENT_MASK (tc_port)) >> -DP_LANE_ASSIGNMENT_SHIFT (tc_port); - -switch (lane_info) { -default : -MISSING_CASE (lane_info); -case 1 : -case 2 : -case 4 : -case 8 : -return 1 ; -case 3 : -case 12 : -return 2 ; -case 15 : -return 4 ; - } -} -/* Theoretical max between source and sink */ static int intel_dp_max_common_lane_count (struct intel_dp *intel_dp) { struct intel_digital_port *intel_dig_port =
dp_to_dig_port(intel_dp);drivers/gpu/drm/i915/intel_dp.c +1
-19int source_max = intel_dig_port->max_lanes;int sink_max =drm_dp_max_lane_count (intel_dp->dpcd); -int fia_max =intel_dp_get_fia_supported_lane_count (intel_dp); +int fia_max =intel_tc_port_fia_max_lane_count (intel_dig_port);return min3 (source_max, sink_max, fia_max); }@@ -5231,195 +5199,6 @@ static bool icl_combo_port_connected(structdrm_i915_private *dev_priv, return I915_READ(SDEISR) & SDE_DDI_HOTPLUG_ICP(port); } -static const char *tc_type_name (enum tc_port_type type) -{ -static const char *const names[] = { - [TC_PORT_UNKNOWN ] ="unknown" , - [TC_PORT_LEGACY ] ="legacy" , - [TC_PORT_TYPEC ] ="typec" , - [TC_PORT_TBT ] ="tbt" , - }; - -if (WARN_ON (type >=ARRAY_SIZE (names))) - type =TC_PORT_UNKNOWN ; - -return names[type]; -} - -static void icl_update_tc_port_type (struct drm_i915_private *dev_priv, -struct intel_digital_port *intel_dig_port, - bool is_legacy, bool is_typec, bool
is_tbt)drivers/gpu/drm/i915/intel_dp.c +0
-21-{ -enum port port = intel_dig_port->base.port; -enum tc_port_type old_type = intel_dig_port->tc_type; - -WARN_ON (is_legacy + is_typec + is_tbt !=1 ); - -if (is_legacy) - intel_dig_port->tc_type =TC_PORT_LEGACY ; -else if (is_typec) - intel_dig_port->tc_type =TC_PORT_TYPEC ; -else if (is_tbt) - intel_dig_port->tc_type =TC_PORT_TBT ; -else -return ; - -/* Types are not supposed to be changed at runtime. */ -WARN_ON (old_type !=TC_PORT_UNKNOWN && - old_type != intel_dig_port->tc_type); - -if (old_type != intel_dig_port->tc_type) - DRM_DEBUG_KMS("Port %c has TC type %s\n",
port_name(port),drivers/gpu/drm/i915/intel_dp.c +0
-5- tc_type_name(intel_dig_port->tc_type)); -} - -/* -* This function implements the first part of the Connect Flow described by our
- * specification, Gen11 TypeC Programming chapter. The rest of the flow (reading
- * lanes, EDID, etc) is done as needed in the typical places.
- *
- * Unlike the other ports, type-C ports are not available to use as soon as we
- * get a hotplug. The type-C PHYs can be shared between multiple controllers:
- * display, USB, etc. As a result, handshaking through FIA is required around
- * connect and disconnect to cleanly transfer ownership with the controller and
- * set the type-C power state.
- *
- * We could opt to only do the connect flow when we actually try to use the AUX
- * channels or do a modeset, then immediately run the disconnect flow after
- * usage, but there are some implications on this for a dynamic environment:
- * things may go away or change behind our backs. So for now our driver is
- * always trying to acquire ownership of the controller as soon as it gets an
- * interrupt (or polls state and sees a port is connected) and only gives it
- * back when it sees a disconnect. Implementation of a more fine- grained model
- * will require a lot of coordination with user space and thorough testing for
- * the extra possible cases.
- */drivers/gpu/drm/i915/intel_dp.c +0
-4-static bool icl_tc_phy_connect (struct drm_i915_private *dev_priv, -struct intel_digital_port *dig_port) -{ - enum tc_port tc_port = intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
drivers/gpu/drm/i915/intel_dp.c +0
-9-u32 val; - -if (dig_port->tc_type !=TC_PORT_LEGACY && - dig_port->tc_type !=TC_PORT_TYPEC ) -return true; - - val =I915_READ (PORT_TX_DFLEXDPPMS ); -if (!(val &DP_PHY_MODE_STATUS_COMPLETED (tc_port))) { - DRM_DEBUG_KMS("DP PHY for TC port %d not ready\n",
tc_port);drivers/gpu/drm/i915/intel_dp.c +0
-6-WARN_ON (dig_port->tc_legacy_port); -return false; - } - -/* -* This function may be called many times in a row without an HPD event
drivers/gpu/drm/i915/intel_dp.c +0
-10-* in between, so try to avoid the write when we can. -*/ - val =I915_READ (PORT_TX_DFLEXDPCSSS ); -if (!(val &DP_PHY_MODE_STATUS_NOT_SAFE (tc_port))) { - val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); -I915_WRITE (PORT_TX_DFLEXDPCSSS , val); - } - -/* -* Now we have to re-check the live state, in case the port recently
drivers/gpu/drm/i915/intel_dp.c +0
-4-* became disconnected. Not necessary for legacy mode. -*/ - if (dig_port->tc_type == TC_PORT_TYPEC && - !(I915_READ(PORT_TX_DFLEXDPSP) &
TC_LIVE_STATE_TC(tc_port))) {drivers/gpu/drm/i915/intel_dp.c +0
-1- DRM_DEBUG_KMS("TC PHY %d sudden disconnect.\n",
tc_port);drivers/gpu/drm/i915/intel_dp.c +0
-9-icl_tc_phy_disconnect (dev_priv, dig_port); -return false; - } - -return true; -} - -/* -* See the comment at the connect function. This implements the Disconnect
- * Flow.
- */drivers/gpu/drm/i915/intel_dp.c +0
-4-void icl_tc_phy_disconnect (struct drm_i915_private *dev_priv, -struct intel_digital_port *dig_port) -{ - enum tc_port tc_port = intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
drivers/gpu/drm/i915/intel_dp.c +0
-6- -if (dig_port->tc_type ==TC_PORT_UNKNOWN ) -return ; - -/* -* TBT disconnection flow is read the live status, what was done in
drivers/gpu/drm/i915/intel_dp.c +0
-20-* caller. -*/ -if (dig_port->tc_type ==TC_PORT_TYPEC || - dig_port->tc_type ==TC_PORT_LEGACY ) { -u32 val; - - val =I915_READ (PORT_TX_DFLEXDPCSSS ); - val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); -I915_WRITE (PORT_TX_DFLEXDPCSSS , val); - } - -DRM_DEBUG_KMS ("Port %c TC type %s disconnected\n" , -port_name (dig_port->base.port), -tc_type_name (dig_port->tc_type)); - - dig_port->tc_type =TC_PORT_UNKNOWN ; -} - -/* -* The type-C ports are different because even when they are connected, they may
- * not be available/usable by the graphics driver: see the comment on
- *icl_tc_phy_connect(). So in our driver instead of adding the additional
- * concept of "usable" and make everything check for "connected and usable" we
- * define a port as "connected" when it is not only connected, but also when it
- * is usable by the rest of the driver. That maintains the old assumption that
- * connected ports are usable, and avoids exposing to the users objects they
- * can't really use.
- */drivers/gpu/drm/i915/intel_dp.c +0
-2-static bool icl_tc_port_connected (struct drm_i915_private *dev_priv, - struct intel_digital_port
*intel_dig_port)drivers/gpu/drm/i915/intel_dp.c +0
-8-{ -enum port port = intel_dig_port->base.port; -enum tc_port tc_port =intel_port_to_tc (dev_priv, port); -bool is_legacy, is_typec, is_tbt; -u32 dpsp; - -/* -* Complain if we got a legacy port HPD, but VBT didn't mark the port as
drivers/gpu/drm/i915/intel_dp.c +0
-5-* legacy. Treat the port as legacy from now on. -*/ -if (!intel_dig_port->tc_legacy_port && -I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) { - DRM_ERROR("VBT incorrectly claims port %c is not TypeClegacy\n",
drivers/gpu/drm/i915/intel_dp.c +0
-7- port_name(port)); - intel_dig_port->tc_legacy_port = true; - } - is_legacy = intel_dig_port->tc_legacy_port; - -/* -* The spec says we shouldn't be using the ISR bits for detecting
drivers/gpu/drm/i915/intel_dp.c +0
-13-* between TC and TBT. We should use DFLEXDPSP. -*/ - dpsp =I915_READ (PORT_TX_DFLEXDPSP ); - is_typec = dpsp &TC_LIVE_STATE_TC (tc_port); - is_tbt = dpsp &TC_LIVE_STATE_TBT (tc_port); - -if (!is_legacy && !is_typec && !is_tbt) { -icl_tc_phy_disconnect (dev_priv, intel_dig_port); - -return false; - } - - icl_update_tc_port_type(dev_priv, intel_dig_port, is_legacy,
is_typec,drivers/gpu/drm/i915/intel_dp.c +0
-8- is_tbt); - -if (!icl_tc_phy_connect (dev_priv, intel_dig_port)) -return false; - -return true; -} - static bool icl_digital_port_connected(struct intel_encoder*encoder)
{drivers/gpu/drm/i915/intel_dp.c +1
-1struct drm_i915_private *dev_priv =to_i915 (encoder->base.dev);@@ -5428,7 +5207,7 @@ static bool icl_digital_port_connected(struct intel_encoder *encoder)if (intel_port_is_combophy (dev_priv, encoder->port))return icl_combo_port_connected (dev_priv, dig_port);else if (intel_port_is_tc (dev_priv, encoder->port)) -return icl_tc_port_connected (dev_priv, dig_port); +return intel_tc_port_connected (dig_port);else MISSING_CASE (encoder->hpd_pin);drivers/gpu/drm/i915/intel_dp.h +0
-2@@ -112,8 +112,6 @@ bool intel_dp_get_colorimetry_status(struct intel_dp *intel_dp);int intel_dp_link_required (int pixel_clock,int bpp);int intel_dp_max_data_rate (int max_link_clock,int max_lanes);bool intel_digital_port_connected (struct intel_encoder *encoder); -void icl_tc_phy_disconnect (struct drm_i915_private *dev_priv, -struct intel_digital_port *dig_port);static inline unsigned int intel_dp_unused_lane_mask (int lane_count){
drivers/gpu/drm/i915/intel_tc.c new file +24
-0@@ -0,0 +1,230 @@ +// SPDX-License-Identifier: MIT +/* +* Copyright © 2019 Intel Corporation +*/ +#include "intel_display.h" +#include "i915_drv.h" +#include "intel_tc.h" + +static const char *tc_type_name (enum tc_port_type type) +{ +static const char *const names[] = { + [TC_PORT_UNKNOWN ] ="unknown" , + [TC_PORT_LEGACY ] ="legacy" , + [TC_PORT_TYPEC ] ="typec" , + [TC_PORT_TBT ] ="tbt" , + }; + +if (WARN_ON (type >=ARRAY_SIZE (names))) + type =TC_PORT_UNKNOWN ; + +return names[type]; +} + +int intel_tc_port_fia_max_lane_count(struct intel_digital_port
*dig_port)drivers/gpu/drm/i915/intel_tc.c new file +2
-0+{ + struct drm_i915_private *dev_priv = to_i915(dig_port-Quoted 1 line
base.base.dev);
drivers/gpu/drm/i915/intel_tc.c new file +1
-0+ enum tc_port tc_port = intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
drivers/gpu/drm/i915/intel_tc.c new file +4
-0+intel_wakeref_t wakeref; +u32 lane_info; + + if (tc_port == PORT_TC_NONE || dig_port->tc_type !=
TC_PORT_TYPEC)drivers/gpu/drm/i915/intel_tc.c new file +4
-0+return 4 ; + + lane_info =0 ; + with_intel_display_power(dev_priv, POWER_DOMAIN_DISPLAY_CORE,wakeref)
drivers/gpu/drm/i915/intel_tc.c new file +22
-0+ lane_info = (I915_READ (PORT_TX_DFLEXDPSP ) & +DP_LANE_ASSIGNMENT_MASK (tc_port)) >> +DP_LANE_ASSIGNMENT_SHIFT (tc_port); + +switch (lane_info) { +default : +MISSING_CASE (lane_info); +case 1 : +case 2 : +case 4 : +case 8 : +return 1 ; +case 3 : +case 12 : +return 2 ; +case 15 : +return 4 ; + } +} + +/* +* This function implements the first part of the Connect Flow described by our
+ * specification, Gen11 TypeC Programming chapter. The rest of the flow (reading
+ * lanes, EDID, etc) is done as needed in the typical places.
+ *
+ * Unlike the other ports, type-C ports are not available to use as soon as we
+ * get a hotplug. The type-C PHYs can be shared between multiple controllers:
+ * display, USB, etc. As a result, handshaking through FIA is required around
+ * connect and disconnect to cleanly transfer ownership with the controller and
+ * set the type-C power state.
+ *
+ * We could opt to only do the connect flow when we actually try to use the AUX
+ * channels or do a modeset, then immediately run the disconnect flow after
+ * usage, but there are some implications on this for a dynamic environment:
+ * things may go away or change behind our backs. So for now our driver is
+ * always trying to acquire ownership of the controller as soon as it gets an
+ * interrupt (or polls state and sees a port is connected) and only gives it
+ * back when it sees a disconnect. Implementation of a more fine- grained model
+ * will require a lot of coordination with user space and thorough testing for
+ * the extra possible cases.
+ */drivers/gpu/drm/i915/intel_tc.c new file +3
-0+static bool icl_tc_phy_connect (struct intel_digital_port *dig_port) +{ + struct drm_i915_private *dev_priv = to_i915(dig_port-Quoted 1 line
base.base.dev);
drivers/gpu/drm/i915/intel_tc.c new file +1
-0+ enum tc_port tc_port = intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
drivers/gpu/drm/i915/intel_tc.c new file +9
-0+u32 val; + +if (dig_port->tc_type !=TC_PORT_LEGACY && + dig_port->tc_type !=TC_PORT_TYPEC ) +return true; + + val =I915_READ (PORT_TX_DFLEXDPPMS ); +if (!(val &DP_PHY_MODE_STATUS_COMPLETED (tc_port))) { + DRM_DEBUG_KMS("DP PHY for TC port %d not ready\n",
tc_port);drivers/gpu/drm/i915/intel_tc.c new file +6
-0+WARN_ON (dig_port->tc_legacy_port); +return false; + } + +/* +* This function may be called many times in a row without an HPD event
drivers/gpu/drm/i915/intel_tc.c new file +10
-0+* in between, so try to avoid the write when we can. +*/ + val =I915_READ (PORT_TX_DFLEXDPCSSS ); +if (!(val &DP_PHY_MODE_STATUS_NOT_SAFE (tc_port))) { + val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); +I915_WRITE (PORT_TX_DFLEXDPCSSS , val); + } + +/* +* Now we have to re-check the live state, in case the port recently
drivers/gpu/drm/i915/intel_tc.c new file +4
-0+* became disconnected. Not necessary for legacy mode. +*/ + if (dig_port->tc_type == TC_PORT_TYPEC && + !(I915_READ(PORT_TX_DFLEXDPSP) &
TC_LIVE_STATE_TC(tc_port))) {drivers/gpu/drm/i915/intel_tc.c new file +1
-0+ DRM_DEBUG_KMS("TC PHY %d sudden disconnect.\n",
tc_port);drivers/gpu/drm/i915/intel_tc.c new file +9
-0+icl_tc_phy_disconnect (dig_port); +return false; + } + +return true; +} + +/* +* See the comment at the connect function. This implements the Disconnect
+ * Flow.
+ */drivers/gpu/drm/i915/intel_tc.c new file +3
-0+void icl_tc_phy_disconnect (struct intel_digital_port *dig_port) +{ + struct drm_i915_private *dev_priv = to_i915(dig_port-Quoted 1 line
base.base.dev);
drivers/gpu/drm/i915/intel_tc.c new file +1
-0+ enum tc_port tc_port = intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
drivers/gpu/drm/i915/intel_tc.c new file +6
-0+ +if (dig_port->tc_type ==TC_PORT_UNKNOWN ) +return ; + +/* +* TBT disconnection flow is read the live status, what was done in
drivers/gpu/drm/i915/intel_tc.c new file +19
-0+* caller. +*/ +if (dig_port->tc_type ==TC_PORT_TYPEC || + dig_port->tc_type ==TC_PORT_LEGACY ) { +u32 val; + + val =I915_READ (PORT_TX_DFLEXDPCSSS ); + val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); +I915_WRITE (PORT_TX_DFLEXDPCSSS , val); + } + +DRM_DEBUG_KMS ("Port %c TC type %s disconnected\n" , +port_name (dig_port->base.port), +tc_type_name (dig_port->tc_type)); + + dig_port->tc_type =TC_PORT_UNKNOWN ; +} + +static void icl_update_tc_port_type(struct drm_i915_private
*dev_priv,drivers/gpu/drm/i915/intel_tc.c new file +1
-0+struct intel_digital_port
*intel_dig_port,drivers/gpu/drm/i915/intel_tc.c new file +1
-0+ bool is_legacy, bool is_typec, bool
is_tbt)drivers/gpu/drm/i915/intel_tc.c new file +21
-0+{ +enum port port = intel_dig_port->base.port; +enum tc_port_type old_type = intel_dig_port->tc_type; + +WARN_ON (is_legacy + is_typec + is_tbt !=1 ); + +if (is_legacy) + intel_dig_port->tc_type =TC_PORT_LEGACY ; +else if (is_typec) + intel_dig_port->tc_type =TC_PORT_TYPEC ; +else if (is_tbt) + intel_dig_port->tc_type =TC_PORT_TBT ; +else +return ; + +/* Types are not supposed to be changed at runtime. */ +WARN_ON (old_type !=TC_PORT_UNKNOWN && + old_type != intel_dig_port->tc_type); + +if (old_type != intel_dig_port->tc_type) + DRM_DEBUG_KMS("Port %c has TC type %s\n",
port_name(port),drivers/gpu/drm/i915/intel_tc.c new file +6
-0+ tc_type_name(intel_dig_port->tc_type)); +} + + +/* +* The type-C ports are different because even when they are connected, they may
+ * not be available/usable by the graphics driver: see the comment on
+ *icl_tc_phy_connect(). So in our driver instead of adding the additional
+ * concept of "usable" and make everything check for "connected and usable" we
+ * define a port as "connected" when it is not only connected, but also when it
+ * is usable by the rest of the driver. That maintains the old assumption that
+ * connected ports are usable, and avoids exposing to the users objects they
+ * can't really use.
+ */drivers/gpu/drm/i915/intel_tc.c new file +3
-0+bool intel_tc_port_connected (struct intel_digital_port *dig_port) +{ + struct drm_i915_private *dev_priv = to_i915(dig_port-Quoted 1 line
base.base.dev);
drivers/gpu/drm/i915/intel_tc.c new file +7
-0+enum port port = dig_port->base.port; +enum tc_port tc_port =intel_port_to_tc (dev_priv, port); +bool is_legacy, is_typec, is_tbt; +u32 dpsp; + +/* +* Complain if we got a legacy port HPD, but VBT didn't mark the port as
drivers/gpu/drm/i915/intel_tc.c new file +5
-0+* legacy. Treat the port as legacy from now on. +*/ +if (!dig_port->tc_legacy_port && +I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) { + DRM_ERROR("VBT incorrectly claims port %c is not TypeClegacy\n",
drivers/gpu/drm/i915/intel_tc.c new file +7
-0+ port_name(port)); + dig_port->tc_legacy_port = true; + } + is_legacy = dig_port->tc_legacy_port; + +/* +* The spec says we shouldn't be using the ISR bits for detecting
drivers/gpu/drm/i915/intel_tc.c new file +13
-0+* between TC and TBT. We should use DFLEXDPSP. +*/ + dpsp =I915_READ (PORT_TX_DFLEXDPSP ); + is_typec = dpsp &TC_LIVE_STATE_TC (tc_port); + is_tbt = dpsp &TC_LIVE_STATE_TBT (tc_port); + +if (!is_legacy && !is_typec && !is_tbt) { +icl_tc_phy_disconnect (dig_port); + +return false; + } + + icl_update_tc_port_type(dev_priv, dig_port, is_legacy,
is_typec,drivers/gpu/drm/i915/intel_tc.c new file +8
-0+ is_tbt); + +if (!icl_tc_phy_connect (dig_port)) +return false; + +return true; +} +drivers/gpu/drm/i915/intel_tc.h new file +11
-0@@ -0,0 +1,13 @@ +#ifndef __INTEL_TC_H__ +#define __INTEL_TC_H__ + +#include <linux/types.h> + +struct intel_digital_port ; + +void icl_tc_phy_disconnect (struct intel_digital_port *dig_port); + +bool intel_tc_port_connected (struct intel_digital_port *dig_port); +int intel_tc_port_fia_max_lane_count(struct intel_digital_port
*dig_port);
drivers/gpu/drm/i915/intel_tc.h line 13
Quoted 2 lines
drivers/gpu/drm/i915/intel_tc.h new file +2
-0+ +#endif /* __INTEL_TC_H__ */
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 4/23 drm/i915: Sanitize the terminology used for TypeC port modes
In reply to Imre DeakThe TypeC port mode can switch dynamically, to reflect that better call the port's mode as 'mode' rather than 'type'.
While at it:
- s/TC_PORT_TBT/TC_PORT_TBT_ALT/ and s/TC_PORT_TYPEC/TC_PORT_DP_ALT/. 'TYPEC' is ambiguous, TBT_ALT and DP_ALT better match the reality.
- Remove the 'unknown' TypeC port mode. The mode is always known, it's the TBT-alt/safe mode after HW reset and after disconnecting the PHY. Simplify the tc_port/tc_type checks accordingly.
- Don't WARN if the port mode changes, that can happen normally.
No functional changes.
--- drivers/gpu/drm/i915/intel_ddi.c | 11 +++--- drivers/gpu/drm/i915/intel_display.h | 7 ++-- drivers/gpu/drm/i915/intel_dp.c | 2 +- drivers/gpu/drm/i915/intel_dpll_mgr.c | 2 +- drivers/gpu/drm/i915/intel_drv.h | 2 +- drivers/gpu/drm/i915/intel_tc.c | 48 +++++++++++---------------- 6 files changed, 31 insertions(+), 41 deletions(-)
drivers/gpu/drm/i915/intel_ddi.c +5 -6
@@ -2986,14 +2986,14 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port)enum tc_port tc_port =intel_port_to_tc (dev_priv, port);u32 ln0, ln1, lane_info; -if (tc_port ==PORT_TC_NONE || intel_dig_port->tc_type ==TC_PORT_TBT ) +if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT )return ; ln0 =I915_READ (MG_DP_MODE (0 , port)); ln1 =I915_READ (MG_DP_MODE (1 , port)); -switch (intel_dig_port->tc_type) { -case TC_PORT_TYPEC : +switch (intel_dig_port->tc_mode) { +case TC_PORT_DP_ALT : ln0 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |MG_DP_MODE_CFG_DP_X2_MODE ); ln1 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |MG_DP_MODE_CFG_DP_X2_MODE );
@@ -3036,7 +3036,7 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port)break ;default : -MISSING_CASE (intel_dig_port->tc_type); +MISSING_CASE (intel_dig_port->tc_mode);return ; }
@@ -3630,8 +3630,7 @@ intel_ddi_pre_pll_enable(struct intel_encoder *encoder,* Program the lane count for static/dynamic connections on Type-C ports. * Skip this step for TBT. */ -if (dig_port->tc_type ==TC_PORT_UNKNOWN || - dig_port->tc_type ==TC_PORT_TBT ) +if (dig_port->tc_mode ==TC_PORT_TBT_ALT )return ;intel_ddi_set_fia_lane_count (encoder, crtc_state, port);
drivers/gpu/drm/i915/intel_display.h +3 -4
@@ -189,10 +189,9 @@ enum tc_port { I915_MAX_TC_PORTS }; -enum tc_port_type { -TC_PORT_UNKNOWN =0 , -TC_PORT_TYPEC , -TC_PORT_TBT , +enum tc_port_mode { +TC_PORT_TBT_ALT , +TC_PORT_DP_ALT ,TC_PORT_LEGACY , };
drivers/gpu/drm/i915/intel_dp.c +1 -1
@@ -1175,7 +1175,7 @@ static u32 skl_get_aux_send_ctl(struct intel_dp *intel_dp,DP_AUX_CH_CTL_FW_SYNC_PULSE_SKL (32 ) |DP_AUX_CH_CTL_SYNC_PULSE_SKL (32 ); -if (intel_dig_port->tc_type ==TC_PORT_TBT ) +if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT ) ret |=DP_AUX_CH_CTL_TBT_IO ;return ret;
drivers/gpu/drm/i915/intel_dpll_mgr.c +1 -1
@@ -2817,7 +2817,7 @@ icl_get_dpll(struct intel_crtc_state *crtc_state, intel_dig_port =enc_to_dig_port (&encoder->base); } -if (intel_dig_port->tc_type ==TC_PORT_TBT ) { +if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT ) { min =DPLL_ID_ICL_TBTPLL ; max = min; ret =icl_calc_dpll_state (crtc_state, encoder);
drivers/gpu/drm/i915/intel_drv.h +1 -1
@@ -1225,7 +1225,7 @@ struct intel_digital_port {enum aux_ch aux_ch;enum intel_display_power_domain ddi_io_power_domain; bool tc_legacy_port:1; -enum tc_port_type tc_type; +enum tc_port_mode tc_mode; void (*write_infoframe)(struct intel_encoder *encoder, const struct intel_crtc_state *crtc_state,
drivers/gpu/drm/i915/intel_tc.c +20 -28
111 lines not on this page · raw message
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 04/23] drm/i915: Sanitize the terminology used for TypeC port modes
Quoted 14 lines · Imre Deak
The TypeC port mode can switch dynamically, to reflect that better call
the port's mode as 'mode' rather than 'type'.While at it:
- s/TC_PORT_TBT/TC_PORT_TBT_ALT/ and s/TC_PORT_TYPEC/TC_PORT_DP_ALT/. 'TYPEC' is ambiguous,TBT_ALTandDP_ALTbetter match the reality.- Remove the 'unknown' TypeC port mode. The mode is always known, it's
the TBT-alt/safe mode after HW reset and after disconnecting the
PHY.
Simplify the tc_port/tc_type checks accordingly.
Quoted 3 lines
- Don't WARN if the port mode changes, that can happen normally.
No functional changes.
There is, the default tc_mode value now is TC_PORT_TBT_ALT instead of TC_PORT_UNKNOWN.
With the change above:
Reviewed-by: José Roberto de Souza <
[email protected]>
Also consider split this patch in two.
Quoted 270 lines
Cc Animesh Manna <[email protected]>Cc Paulo Zanoni <[email protected]>Cc Anusha Srivatsa <[email protected]>Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_ddi.c | 11 +++--- drivers/gpu/drm/i915/intel_display.h | 7 ++-- drivers/gpu/drm/i915/intel_dp.c | 2 +- drivers/gpu/drm/i915/intel_dpll_mgr.c | 2 +- drivers/gpu/drm/i915/intel_drv.h | 2 +- drivers/gpu/drm/i915/intel_tc.c | 48 +++++++++++------------ ---- 6 files changed, 31 insertions(+), 41 deletions(-)drivers/gpu/drm/i915/intel_ddi.c +3
-3@@ -2986,14 +2986,14 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port)enum tc_port tc_port =intel_port_to_tc (dev_priv, port);u32 ln0, ln1, lane_info; -if (tc_port ==PORT_TC_NONE || intel_dig_port->tc_type == TC_PORT_TBT) +if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT )return ; ln0 =I915_READ (MG_DP_MODE (0 , port)); ln1 =I915_READ (MG_DP_MODE (1 , port)); -switch (intel_dig_port->tc_type) { -case TC_PORT_TYPEC : +switch (intel_dig_port->tc_mode) { +case TC_PORT_DP_ALT : ln0 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |
MG_DP_MODE_CFG_DP_X2_MODE);
ln1 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |MG_DP_MODE_CFG_DP_X2_MODE);drivers/gpu/drm/i915/intel_ddi.c +1
-1@@ -3036,7 +3036,7 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port) break;default : -MISSING_CASE (intel_dig_port->tc_type); +MISSING_CASE (intel_dig_port->tc_mode);return ; }@@ -3630,8 +3630,7 @@ intel_ddi_pre_pll_enable(struct intel_encoder *encoder, * Program the lane count for static/dynamic connections onType-C ports.
drivers/gpu/drm/i915/intel_ddi.c +1
-2* Skip this step for TBT. */ -if (dig_port->tc_type ==TC_PORT_UNKNOWN || - dig_port->tc_type ==TC_PORT_TBT ) +if (dig_port->tc_mode ==TC_PORT_TBT_ALT )return ;intel_ddi_set_fia_lane_count (encoder, crtc_state, port);drivers/gpu/drm/i915/intel_display.h +3
-4@@ -189,10 +189,9 @@ enum tc_port { I915_MAX_TC_PORTS }; -enum tc_port_type { -TC_PORT_UNKNOWN =0 , -TC_PORT_TYPEC , -TC_PORT_TBT , +enum tc_port_mode { +TC_PORT_TBT_ALT , +TC_PORT_DP_ALT ,TC_PORT_LEGACY , };drivers/gpu/drm/i915/intel_dp.c +1
-1@@ -1175,7 +1175,7 @@ static u32 skl_get_aux_send_ctl(struct intel_dp *intel_dp,DP_AUX_CH_CTL_FW_SYNC_PULSE_SKL (32 ) |DP_AUX_CH_CTL_SYNC_PULSE_SKL (32 ); -if (intel_dig_port->tc_type ==TC_PORT_TBT ) +if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT ) ret |=DP_AUX_CH_CTL_TBT_IO ;drivers/gpu/drm/i915/intel_dp.c +0
-0return ret;drivers/gpu/drm/i915/intel_dpll_mgr.c +1
-1@@ -2817,7 +2817,7 @@ icl_get_dpll(struct intel_crtc_state *crtc_state, intel_dig_port =enc_to_dig_port (&encoder- >base); } -if (intel_dig_port->tc_type ==TC_PORT_TBT ) { +if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT ) { min =DPLL_ID_ICL_TBTPLL ;drivers/gpu/drm/i915/intel_dpll_mgr.c +0
-0max = min; ret =icl_calc_dpll_state (crtc_state, encoder);drivers/gpu/drm/i915/intel_drv.h +1
-1@@ -1225,7 +1225,7 @@ struct intel_digital_port {enum aux_ch aux_ch;enum intel_display_power_domain ddi_io_power_domain; bool tc_legacy_port:1; -enum tc_port_type tc_type; +enum tc_port_mode tc_mode;void (*write_infoframe)(struct intel_encoder *encoder, const struct intel_crtc_state
*crtc_state,drivers/gpu/drm/i915/intel_tc.c +6
-7@@ -6,19 +6,18 @@#include "i915_drv.h" #include "intel_tc.h" -static const char *tc_type_name (enum tc_port_type type) +static const char *tc_port_mode_name (enum tc_port_mode mode) {static const char *const names[] = { - [TC_PORT_UNKNOWN ] ="unknown" , + [TC_PORT_TBT_ALT ] ="tbt-alt" , + [TC_PORT_DP_ALT ] ="dp-alt" , [TC_PORT_LEGACY ] ="legacy" , - [TC_PORT_TYPEC ] ="typec" , - [TC_PORT_TBT ] ="tbt" , }; -if (WARN_ON (type >=ARRAY_SIZE (names))) - type =TC_PORT_UNKNOWN ; +if (WARN_ON (mode >=ARRAY_SIZE (names))) + mode =TC_PORT_TBT_ALT ; -return names[type]; +return names[mode]; } int intel_tc_port_fia_max_lane_count(struct intel_digital_port
*dig_port)drivers/gpu/drm/i915/intel_tc.c +1
-1@@ -28,7 +27,7 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) intel_wakeref_t wakeref;u32 lane_info; -if (tc_port ==PORT_TC_NONE || dig_port->tc_type != TC_PORT_TYPEC) +if (dig_port->tc_mode !=TC_PORT_DP_ALT )return 4 ;drivers/gpu/drm/i915/intel_tc.c +2
-2lane_info =0 ;@@ -80,8 +79,8 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port)enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port- >base.port);u32 val; -if (dig_port->tc_type !=TC_PORT_LEGACY && - dig_port->tc_type !=TC_PORT_TYPEC ) +if (dig_port->tc_mode !=TC_PORT_LEGACY && + dig_port->tc_mode !=TC_PORT_DP_ALT )return true;drivers/gpu/drm/i915/intel_tc.c +0
-0val =I915_READ (PORT_TX_DFLEXDPPMS );@@ -105,7 +104,7 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port) * Now we have to re-check the live state, in case the portrecently
drivers/gpu/drm/i915/intel_tc.c +1
-1* became disconnected. Not necessary for legacy mode. */ - if (dig_port->tc_type == TC_PORT_TYPEC && + if (dig_port->tc_mode == TC_PORT_DP_ALT && !(I915_READ(PORT_TX_DFLEXDPSP) &
TC_LIVE_STATE_TC(tc_port))) {
DRM_DEBUG_KMS("TC PHY %d sudden disconnect.\n",tc_port);drivers/gpu/drm/i915/intel_tc.c +0
-3icl_tc_phy_disconnect (dig_port);@@ -124,15 +123,12 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port)struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port- >base.port); -if (dig_port->tc_type ==TC_PORT_UNKNOWN ) -return ; -/* * TBT disconnection flow is read the live status, what was done in
drivers/gpu/drm/i915/intel_tc.c +4
-4* caller. */ -if (dig_port->tc_type ==TC_PORT_TYPEC || - dig_port->tc_type ==TC_PORT_LEGACY ) { +if (dig_port->tc_mode ==TC_PORT_DP_ALT || + dig_port->tc_mode ==TC_PORT_LEGACY ) {u32 val; val =I915_READ (PORT_TX_DFLEXDPCSSS );@@ -142,9 +138,9 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port) DRM_DEBUG_KMS("Port %c TC type %s disconnected\n",port_name (dig_port->base.port), - tc_type_name(dig_port->tc_type)); + tc_port_mode_name(dig_port->tc_mode)); - dig_port->tc_type =TC_PORT_UNKNOWN ; + dig_port->tc_mode =TC_PORT_TBT_ALT ; }static void icl_update_tc_port_type(struct
drm_i915_private*dev_priv,drivers/gpu/drm/i915/intel_tc.c +6
-10@@ -152,26 +148,22 @@ static void icl_update_tc_port_type(structdrm_i915_private *dev_priv, bool is_legacy, bool is_typec, bool is_tbt) { enum port port = intel_dig_port->base.port; -enum tc_port_type old_type = intel_dig_port->tc_type; +enum tc_port_mode old_mode = intel_dig_port->tc_mode;WARN_ON (is_legacy + is_typec + is_tbt !=1 );if (is_legacy) - intel_dig_port->tc_type =TC_PORT_LEGACY ; + intel_dig_port->tc_mode =TC_PORT_LEGACY ;else if (is_typec) - intel_dig_port->tc_type =TC_PORT_TYPEC ; + intel_dig_port->tc_mode =TC_PORT_DP_ALT ;else if (is_tbt) - intel_dig_port->tc_type =TC_PORT_TBT ; + intel_dig_port->tc_mode =TC_PORT_TBT_ALT ;else return ; -/* Types are not supposed to be changed at runtime. */ -WARN_ON (old_type !=TC_PORT_UNKNOWN && - old_type != intel_dig_port->tc_type); - -if (old_type != intel_dig_port->tc_type) + if (old_mode != intel_dig_port->tc_mode) DRM_DEBUG_KMS("Port %c has TC type %s\n", port_name(port), -tc_type_name (intel_dig_port->tc_type)); + tc_port_mode_name(intel_dig_port-Quoted 1 line
tc_mode));
Quoted 3 lines
}
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 04/23] drm/i915: Sanitize the terminology used for TypeC port modes
Quoted 15 lines · Jose
Quoted 14 lines · Imre Deak
The TypeC port mode can switch dynamically, to reflect that better call
the port's mode as 'mode' rather than 'type'.While at it:
- s/TC_PORT_TBT/TC_PORT_TBT_ALT/ and s/TC_PORT_TYPEC/TC_PORT_DP_ALT/. 'TYPEC' is ambiguous,TBT_ALTandDP_ALTbetter match the reality.- Remove the 'unknown' TypeC port mode. The mode is always known, it's
the TBT-alt/safe mode after HW reset and after disconnecting the
PHY.
Simplify the tc_port/tc_type checks accordingly.
Quoted 6 lines
Quoted 3 lines
- Don't WARN if the port mode changes, that can happen normally.
No functional changes.
There is, the default
tc_modevalue now isTC_PORT_TBT_ALTinstead ofTC_PORT_UNKNOWN.
That doesn't change the functionality. Before the change the two modes were treated the same way; that fact motivated the change to remove TC_PORT_UNKNOWN and just use TC_PORT_TBT_ALT instead, which I tried to explain in the commit log.
Quoted 5 lines
With the change above:
Reviewed-by José Roberto de Souza <[email protected]>Also consider split this patch in two.
Makes sense to keep it as-is, based on keeping the functionality as described above?
Quoted 269 lines
Quoted 269 lines
Cc Animesh Manna <[email protected]>Cc Paulo Zanoni <[email protected]>Cc Anusha Srivatsa <[email protected]>Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_ddi.c | 11 +++--- drivers/gpu/drm/i915/intel_display.h | 7 ++-- drivers/gpu/drm/i915/intel_dp.c | 2 +- drivers/gpu/drm/i915/intel_dpll_mgr.c | 2 +- drivers/gpu/drm/i915/intel_drv.h | 2 +- drivers/gpu/drm/i915/intel_tc.c | 48 +++++++++++------------ ---- 6 files changed, 31 insertions(+), 41 deletions(-)drivers/gpu/drm/i915/intel_ddi.c +3
-3@@ -2986,14 +2986,14 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port)enum tc_port tc_port =intel_port_to_tc (dev_priv, port);u32 ln0, ln1, lane_info; -if (tc_port ==PORT_TC_NONE || intel_dig_port->tc_type == TC_PORT_TBT) +if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT )return ; ln0 =I915_READ (MG_DP_MODE (0 , port)); ln1 =I915_READ (MG_DP_MODE (1 , port)); -switch (intel_dig_port->tc_type) { -case TC_PORT_TYPEC : +switch (intel_dig_port->tc_mode) { +case TC_PORT_DP_ALT : ln0 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |
MG_DP_MODE_CFG_DP_X2_MODE);
ln1 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |MG_DP_MODE_CFG_DP_X2_MODE);drivers/gpu/drm/i915/intel_ddi.c +1
-1@@ -3036,7 +3036,7 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port) break;default : -MISSING_CASE (intel_dig_port->tc_type); +MISSING_CASE (intel_dig_port->tc_mode);return ; }@@ -3630,8 +3630,7 @@ intel_ddi_pre_pll_enable(struct intel_encoder *encoder, * Program the lane count for static/dynamic connections onType-C ports.
drivers/gpu/drm/i915/intel_ddi.c +1
-2* Skip this step for TBT. */ -if (dig_port->tc_type ==TC_PORT_UNKNOWN || - dig_port->tc_type ==TC_PORT_TBT ) +if (dig_port->tc_mode ==TC_PORT_TBT_ALT )return ;intel_ddi_set_fia_lane_count (encoder, crtc_state, port);drivers/gpu/drm/i915/intel_display.h +3
-4@@ -189,10 +189,9 @@ enum tc_port { I915_MAX_TC_PORTS }; -enum tc_port_type { -TC_PORT_UNKNOWN =0 , -TC_PORT_TYPEC , -TC_PORT_TBT , +enum tc_port_mode { +TC_PORT_TBT_ALT , +TC_PORT_DP_ALT ,TC_PORT_LEGACY , };drivers/gpu/drm/i915/intel_dp.c +1
-1@@ -1175,7 +1175,7 @@ static u32 skl_get_aux_send_ctl(struct intel_dp *intel_dp,DP_AUX_CH_CTL_FW_SYNC_PULSE_SKL (32 ) |DP_AUX_CH_CTL_SYNC_PULSE_SKL (32 ); -if (intel_dig_port->tc_type ==TC_PORT_TBT ) +if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT ) ret |=DP_AUX_CH_CTL_TBT_IO ;drivers/gpu/drm/i915/intel_dp.c +0
-0return ret;drivers/gpu/drm/i915/intel_dpll_mgr.c +1
-1@@ -2817,7 +2817,7 @@ icl_get_dpll(struct intel_crtc_state *crtc_state, intel_dig_port =enc_to_dig_port (&encoder- >base); } -if (intel_dig_port->tc_type ==TC_PORT_TBT ) { +if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT ) { min =DPLL_ID_ICL_TBTPLL ;drivers/gpu/drm/i915/intel_dpll_mgr.c +0
-0max = min; ret =icl_calc_dpll_state (crtc_state, encoder);drivers/gpu/drm/i915/intel_drv.h +1
-1@@ -1225,7 +1225,7 @@ struct intel_digital_port {enum aux_ch aux_ch;enum intel_display_power_domain ddi_io_power_domain; bool tc_legacy_port:1; -enum tc_port_type tc_type; +enum tc_port_mode tc_mode;void (*write_infoframe)(struct intel_encoder *encoder, const struct intel_crtc_state
*crtc_state,drivers/gpu/drm/i915/intel_tc.c +6
-7@@ -6,19 +6,18 @@#include "i915_drv.h" #include "intel_tc.h" -static const char *tc_type_name (enum tc_port_type type) +static const char *tc_port_mode_name (enum tc_port_mode mode) {static const char *const names[] = { - [TC_PORT_UNKNOWN ] ="unknown" , + [TC_PORT_TBT_ALT ] ="tbt-alt" , + [TC_PORT_DP_ALT ] ="dp-alt" , [TC_PORT_LEGACY ] ="legacy" , - [TC_PORT_TYPEC ] ="typec" , - [TC_PORT_TBT ] ="tbt" , }; -if (WARN_ON (type >=ARRAY_SIZE (names))) - type =TC_PORT_UNKNOWN ; +if (WARN_ON (mode >=ARRAY_SIZE (names))) + mode =TC_PORT_TBT_ALT ; -return names[type]; +return names[mode]; } int intel_tc_port_fia_max_lane_count(struct intel_digital_port
*dig_port)drivers/gpu/drm/i915/intel_tc.c +1
-1@@ -28,7 +27,7 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) intel_wakeref_t wakeref;u32 lane_info; -if (tc_port ==PORT_TC_NONE || dig_port->tc_type != TC_PORT_TYPEC) +if (dig_port->tc_mode !=TC_PORT_DP_ALT )return 4 ;drivers/gpu/drm/i915/intel_tc.c +2
-2lane_info =0 ;@@ -80,8 +79,8 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port)enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port- >base.port);u32 val; -if (dig_port->tc_type !=TC_PORT_LEGACY && - dig_port->tc_type !=TC_PORT_TYPEC ) +if (dig_port->tc_mode !=TC_PORT_LEGACY && + dig_port->tc_mode !=TC_PORT_DP_ALT )return true;drivers/gpu/drm/i915/intel_tc.c +0
-0val =I915_READ (PORT_TX_DFLEXDPPMS );@@ -105,7 +104,7 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port) * Now we have to re-check the live state, in case the portrecently
drivers/gpu/drm/i915/intel_tc.c +1
-1* became disconnected. Not necessary for legacy mode. */ - if (dig_port->tc_type == TC_PORT_TYPEC && + if (dig_port->tc_mode == TC_PORT_DP_ALT && !(I915_READ(PORT_TX_DFLEXDPSP) &
TC_LIVE_STATE_TC(tc_port))) {
DRM_DEBUG_KMS("TC PHY %d sudden disconnect.\n",tc_port);drivers/gpu/drm/i915/intel_tc.c +0
-3icl_tc_phy_disconnect (dig_port);@@ -124,15 +123,12 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port)struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port- >base.port); -if (dig_port->tc_type ==TC_PORT_UNKNOWN ) -return ; -/* * TBT disconnection flow is read the live status, what was done in
drivers/gpu/drm/i915/intel_tc.c +4
-4* caller. */ -if (dig_port->tc_type ==TC_PORT_TYPEC || - dig_port->tc_type ==TC_PORT_LEGACY ) { +if (dig_port->tc_mode ==TC_PORT_DP_ALT || + dig_port->tc_mode ==TC_PORT_LEGACY ) {u32 val; val =I915_READ (PORT_TX_DFLEXDPCSSS );@@ -142,9 +138,9 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port) DRM_DEBUG_KMS("Port %c TC type %s disconnected\n",port_name (dig_port->base.port), - tc_type_name(dig_port->tc_type)); + tc_port_mode_name(dig_port->tc_mode)); - dig_port->tc_type =TC_PORT_UNKNOWN ; + dig_port->tc_mode =TC_PORT_TBT_ALT ; }static void icl_update_tc_port_type(struct
drm_i915_private*dev_priv,drivers/gpu/drm/i915/intel_tc.c +6
-10@@ -152,26 +148,22 @@ static void icl_update_tc_port_type(structdrm_i915_private *dev_priv, bool is_legacy, bool is_typec, bool is_tbt) { enum port port = intel_dig_port->base.port; -enum tc_port_type old_type = intel_dig_port->tc_type; +enum tc_port_mode old_mode = intel_dig_port->tc_mode;WARN_ON (is_legacy + is_typec + is_tbt !=1 );if (is_legacy) - intel_dig_port->tc_type =TC_PORT_LEGACY ; + intel_dig_port->tc_mode =TC_PORT_LEGACY ;else if (is_typec) - intel_dig_port->tc_type =TC_PORT_TYPEC ; + intel_dig_port->tc_mode =TC_PORT_DP_ALT ;else if (is_tbt) - intel_dig_port->tc_type =TC_PORT_TBT ; + intel_dig_port->tc_mode =TC_PORT_TBT_ALT ;else return ; -/* Types are not supposed to be changed at runtime. */ -WARN_ON (old_type !=TC_PORT_UNKNOWN && - old_type != intel_dig_port->tc_type); - -if (old_type != intel_dig_port->tc_type) + if (old_mode != intel_dig_port->tc_mode) DRM_DEBUG_KMS("Port %c has TC type %s\n", port_name(port), -tc_type_name (intel_dig_port->tc_type)); + tc_port_mode_name(intel_dig_port-
Quoted 4 lines
Quoted 4 lines
Quoted 1 line
tc_mode));}
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 04/23] drm/i915: Sanitize the terminology used for TypeC port modes
In reply to Imre DeakQuoted 6 lines · Imre Deak
The TypeC port mode can switch dynamically, to reflect that better call the port's mode as 'mode' rather than 'type'.
While at it:
- s/TC_PORT_TBT/TC_PORT_TBT_ALT/ and s/TC_PORT_TYPEC/TC_PORT_DP_ALT/. 'TYPEC' is ambiguous,TBT_ALTandDP_ALTbetter match the reality.
\o/
Quoted 4 lines
- Remove the 'unknown' TypeC port mode. The mode is always known, it's the TBT-alt/safe mode after HW reset and after disconnecting the PHY. Simplify the tc_port/tc_type checks accordingly.
I think the unknown was there to cover the first time we set the type (aka mode). Since we don't do this during initialization and only when updating the connected state, we needed that to protect some functions.
Quoted 110 lines
- Don't WARN if the port mode changes, that can happen normally.
No functional changes.
Cc Animesh Manna <[email protected]>Cc Paulo Zanoni <[email protected]>Cc Anusha Srivatsa <[email protected]>Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Signed-off-by Imre Deak <[email protected]>---
drivers/gpu/drm/i915/intel_ddi.c | 11 +++--- drivers/gpu/drm/i915/intel_display.h | 7 ++-- drivers/gpu/drm/i915/intel_dp.c | 2 +- drivers/gpu/drm/i915/intel_dpll_mgr.c | 2 +- drivers/gpu/drm/i915/intel_drv.h | 2 +- drivers/gpu/drm/i915/intel_tc.c | 48 +++++++++++---------------- 6 files changed, 31 insertions(+), 41 deletions(-)drivers/gpu/drm/i915/intel_ddi.c +5
-6@@ -2986,14 +2986,14 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port)enum tc_port tc_port =intel_port_to_tc (dev_priv, port);u32 ln0, ln1, lane_info; -if (tc_port ==PORT_TC_NONE || intel_dig_port->tc_type ==TC_PORT_TBT ) +if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT )return ; ln0 =I915_READ (MG_DP_MODE (0 , port)); ln1 =I915_READ (MG_DP_MODE (1 , port)); -switch (intel_dig_port->tc_type) { -case TC_PORT_TYPEC : +switch (intel_dig_port->tc_mode) { +case TC_PORT_DP_ALT : ln0 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |MG_DP_MODE_CFG_DP_X2_MODE ); ln1 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |MG_DP_MODE_CFG_DP_X2_MODE );@@ -3036,7 +3036,7 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port)break ;default : -MISSING_CASE (intel_dig_port->tc_type); +MISSING_CASE (intel_dig_port->tc_mode);return ; }@@ -3630,8 +3630,7 @@ intel_ddi_pre_pll_enable(struct intel_encoder *encoder,* Program the lane count for static/dynamic connections on Type-C ports. * Skip this step for TBT. */ -if (dig_port->tc_type ==TC_PORT_UNKNOWN || - dig_port->tc_type ==TC_PORT_TBT ) +if (dig_port->tc_mode ==TC_PORT_TBT_ALT )return ;intel_ddi_set_fia_lane_count (encoder, crtc_state, port);drivers/gpu/drm/i915/intel_display.h +3
-4@@ -189,10 +189,9 @@ enum tc_port { I915_MAX_TC_PORTS }; -enum tc_port_type { -TC_PORT_UNKNOWN =0 , -TC_PORT_TYPEC , -TC_PORT_TBT , +enum tc_port_mode { +TC_PORT_TBT_ALT , +TC_PORT_DP_ALT ,TC_PORT_LEGACY , };drivers/gpu/drm/i915/intel_dp.c +1
-1@@ -1175,7 +1175,7 @@ static u32 skl_get_aux_send_ctl(struct intel_dp *intel_dp,DP_AUX_CH_CTL_FW_SYNC_PULSE_SKL (32 ) |DP_AUX_CH_CTL_SYNC_PULSE_SKL (32 ); -if (intel_dig_port->tc_type ==TC_PORT_TBT ) +if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT ) ret |=DP_AUX_CH_CTL_TBT_IO ;return ret;drivers/gpu/drm/i915/intel_dpll_mgr.c +1
-1@@ -2817,7 +2817,7 @@ icl_get_dpll(struct intel_crtc_state *crtc_state, intel_dig_port =enc_to_dig_port (&encoder->base); } -if (intel_dig_port->tc_type ==TC_PORT_TBT ) { +if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT ) { min =DPLL_ID_ICL_TBTPLL ; max = min; ret =icl_calc_dpll_state (crtc_state, encoder);drivers/gpu/drm/i915/intel_drv.h +0
-0
drivers/gpu/drm/i915/intel_drv.h struct intel_digital_port { · line 1227
Quoted 3 lines
drivers/gpu/drm/i915/intel_drv.h +0
-0@@ -1225,7 +1225,7 @@ struct intel_digital_port {enum aux_ch aux_ch;enum intel_display_power_domain ddi_io_power_domain; bool tc_legacy_port:1;
not related, but why do we add a hole in the struct on purpose?!?
Quoted 83 lines
drivers/gpu/drm/i915/intel_drv.h +1
-1-enum tc_port_type tc_type; +enum tc_port_mode tc_mode; void (*write_infoframe)(struct intel_encoder *encoder, const struct intel_crtc_state *crtc_state,drivers/gpu/drm/i915/intel_tc.c +12
-16@@ -6,19 +6,18 @@#include "i915_drv.h" #include "intel_tc.h" -static const char *tc_type_name (enum tc_port_type type) +static const char *tc_port_mode_name (enum tc_port_mode mode) {static const char *const names[] = { - [TC_PORT_UNKNOWN ] ="unknown" , + [TC_PORT_TBT_ALT ] ="tbt-alt" , + [TC_PORT_DP_ALT ] ="dp-alt" , [TC_PORT_LEGACY ] ="legacy" , - [TC_PORT_TYPEC ] ="typec" , - [TC_PORT_TBT ] ="tbt" , }; -if (WARN_ON (type >=ARRAY_SIZE (names))) - type =TC_PORT_UNKNOWN ; +if (WARN_ON (mode >=ARRAY_SIZE (names))) + mode =TC_PORT_TBT_ALT ; -return names[type]; +return names[mode]; }int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port)@@ -28,7 +27,7 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port)intel_wakeref_t wakeref;u32 lane_info; -if (tc_port ==PORT_TC_NONE || dig_port->tc_type !=TC_PORT_TYPEC ) +if (dig_port->tc_mode !=TC_PORT_DP_ALT )return 4 ; lane_info =0 ;@@ -80,8 +79,8 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port)enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port);u32 val; -if (dig_port->tc_type !=TC_PORT_LEGACY && - dig_port->tc_type !=TC_PORT_TYPEC ) +if (dig_port->tc_mode !=TC_PORT_LEGACY && + dig_port->tc_mode !=TC_PORT_DP_ALT )return true; val =I915_READ (PORT_TX_DFLEXDPPMS );@@ -105,7 +104,7 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port)* Now we have to re-check the live state, in case the port recently * became disconnected. Not necessary for legacy mode. */ -if (dig_port->tc_type ==TC_PORT_TYPEC && +if (dig_port->tc_mode ==TC_PORT_DP_ALT && !(I915_READ (PORT_TX_DFLEXDPSP ) &TC_LIVE_STATE_TC (tc_port))) {DRM_DEBUG_KMS ("TC PHY %d sudden disconnect.\n" , tc_port);icl_tc_phy_disconnect (dig_port);@@ -124,15 +123,12 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port)struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); -if (dig_port->tc_type ==TC_PORT_UNKNOWN ) -return ; -/* * TBT disconnection flow is read the live status, what was done in * caller. */ -if (dig_port->tc_type ==TC_PORT_TYPEC || - dig_port->tc_type ==TC_PORT_LEGACY ) { +if (dig_port->tc_mode ==TC_PORT_DP_ALT || + dig_port->tc_mode ==TC_PORT_LEGACY ) {u32 val; val =I915_READ (PORT_TX_DFLEXDPCSSS );
drivers/gpu/drm/i915/intel_tc.c void icl_tc_phy_disconnect(struct intel_digital_port *dig_port) · line 143
Quoted 8 lines
drivers/gpu/drm/i915/intel_tc.c +2
-2@@ -142,9 +138,9 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port)DRM_DEBUG_KMS ("Port %c TC type %s disconnected\n" ,port_name (dig_port->base.port), -tc_type_name (dig_port->tc_type)); +tc_port_mode_name (dig_port->tc_mode)); - dig_port->tc_type =TC_PORT_UNKNOWN ; + dig_port->tc_mode =TC_PORT_TBT_ALT ;
humn... if this is what the hw has after reset, then I think it covers my concern above.
Lucas De Marchi
Quoted 43 lines
drivers/gpu/drm/i915/intel_tc.c +6
-10} static void icl_update_tc_port_type(struct drm_i915_private *dev_priv,@@ -152,26 +148,22 @@ static void icl_update_tc_port_type(struct drm_i915_private *dev_priv, bool is_legacy, bool is_typec, bool is_tbt) { enum port port = intel_dig_port->base.port; -enum tc_port_type old_type = intel_dig_port->tc_type; +enum tc_port_mode old_mode = intel_dig_port->tc_mode;WARN_ON (is_legacy + is_typec + is_tbt !=1 );if (is_legacy) - intel_dig_port->tc_type =TC_PORT_LEGACY ; + intel_dig_port->tc_mode =TC_PORT_LEGACY ;else if (is_typec) - intel_dig_port->tc_type =TC_PORT_TYPEC ; + intel_dig_port->tc_mode =TC_PORT_DP_ALT ;else if (is_tbt) - intel_dig_port->tc_type =TC_PORT_TBT ; + intel_dig_port->tc_mode =TC_PORT_TBT_ALT ;else return ; -/* Types are not supposed to be changed at runtime. */ -WARN_ON (old_type !=TC_PORT_UNKNOWN && - old_type != intel_dig_port->tc_type); - -if (old_type != intel_dig_port->tc_type) +if (old_mode != intel_dig_port->tc_mode)DRM_DEBUG_KMS ("Port %c has TC type %s\n" ,port_name (port), -tc_type_name (intel_dig_port->tc_type)); +tc_port_mode_name (intel_dig_port->tc_mode)); }Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 04/23] drm/i915: Sanitize the terminology used for TypeC port modes
Quoted 11 lines · Lucas De Marchi
Quoted 6 lines · Imre Deak
The TypeC port mode can switch dynamically, to reflect that better call the port's mode as 'mode' rather than 'type'.
While at it:
- s/TC_PORT_TBT/TC_PORT_TBT_ALT/ and s/TC_PORT_TYPEC/TC_PORT_DP_ALT/. 'TYPEC' is ambiguous,TBT_ALTandDP_ALTbetter match the reality.\o/
Quoted 1 line
Quoted 7 lines
Quoted 3 lines
- Remove the 'unknown' TypeC port mode. The mode is always known, it's the TBT-alt/safe mode after HW reset and after disconnecting the PHY. Simplify the tc_port/tc_type checks accordingly.
I think the unknown was there to cover the first time we set the type (aka mode). Since we don't do this during initialization and only when updating the connected state, we needed that to protect some functions.
Ok, but the mode is still known even before updating the connected state (that is probing), we just have to make sure that we read out the HW state (which is what this mode is) early enough. At least selecting the proper AUX power well (DP-Alt or TBT-Alt AUX) depends on this.
That HW readout happens already now via the intel_ddi_init() function.
Quoted 100 lines
Quoted 100 lines
- Don't WARN if the port mode changes, that can happen normally.
No functional changes.
Cc Animesh Manna <[email protected]>Cc Paulo Zanoni <[email protected]>Cc Anusha Srivatsa <[email protected]>Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Signed-off-by Imre Deak <[email protected]>---
drivers/gpu/drm/i915/intel_ddi.c | 11 +++--- drivers/gpu/drm/i915/intel_display.h | 7 ++-- drivers/gpu/drm/i915/intel_dp.c | 2 +- drivers/gpu/drm/i915/intel_dpll_mgr.c | 2 +- drivers/gpu/drm/i915/intel_drv.h | 2 +- drivers/gpu/drm/i915/intel_tc.c | 48 +++++++++++---------------- 6 files changed, 31 insertions(+), 41 deletions(-)drivers/gpu/drm/i915/intel_ddi.c +5
-6@@ -2986,14 +2986,14 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port)enum tc_port tc_port =intel_port_to_tc (dev_priv, port);u32 ln0, ln1, lane_info; -if (tc_port ==PORT_TC_NONE || intel_dig_port->tc_type ==TC_PORT_TBT ) +if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT )return ; ln0 =I915_READ (MG_DP_MODE (0 , port)); ln1 =I915_READ (MG_DP_MODE (1 , port)); -switch (intel_dig_port->tc_type) { -case TC_PORT_TYPEC : +switch (intel_dig_port->tc_mode) { +case TC_PORT_DP_ALT : ln0 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |MG_DP_MODE_CFG_DP_X2_MODE ); ln1 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |MG_DP_MODE_CFG_DP_X2_MODE );@@ -3036,7 +3036,7 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port)break ;default : -MISSING_CASE (intel_dig_port->tc_type); +MISSING_CASE (intel_dig_port->tc_mode);return ; }@@ -3630,8 +3630,7 @@ intel_ddi_pre_pll_enable(struct intel_encoder *encoder,* Program the lane count for static/dynamic connections on Type-C ports. * Skip this step for TBT. */ -if (dig_port->tc_type ==TC_PORT_UNKNOWN || - dig_port->tc_type ==TC_PORT_TBT ) +if (dig_port->tc_mode ==TC_PORT_TBT_ALT )return ;intel_ddi_set_fia_lane_count (encoder, crtc_state, port);drivers/gpu/drm/i915/intel_display.h +3
-4@@ -189,10 +189,9 @@ enum tc_port { I915_MAX_TC_PORTS }; -enum tc_port_type { -TC_PORT_UNKNOWN =0 , -TC_PORT_TYPEC , -TC_PORT_TBT , +enum tc_port_mode { +TC_PORT_TBT_ALT , +TC_PORT_DP_ALT ,TC_PORT_LEGACY , };drivers/gpu/drm/i915/intel_dp.c +1
-1@@ -1175,7 +1175,7 @@ static u32 skl_get_aux_send_ctl(struct intel_dp *intel_dp,DP_AUX_CH_CTL_FW_SYNC_PULSE_SKL (32 ) |DP_AUX_CH_CTL_SYNC_PULSE_SKL (32 ); -if (intel_dig_port->tc_type ==TC_PORT_TBT ) +if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT ) ret |=DP_AUX_CH_CTL_TBT_IO ;return ret;drivers/gpu/drm/i915/intel_dpll_mgr.c +0
-0@@ -2817,7 +2817,7 @@ icl_get_dpll(struct intel_crtc_state *crtc_state, intel_dig_port =enc_to_dig_port (&encoder->base); }
Quoted 15 lines
drivers/gpu/drm/i915/intel_drv.h struct intel_digital_port { · line 1227
Quoted 13 lines
drivers/gpu/drm/i915/intel_dpll_mgr.c +1
-1-if (intel_dig_port->tc_type ==TC_PORT_TBT ) { +if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT ) { min =DPLL_ID_ICL_TBTPLL ; max = min; ret =icl_calc_dpll_state (crtc_state, encoder);drivers/gpu/drm/i915/intel_drv.h +0
-0@@ -1225,7 +1225,7 @@ struct intel_digital_port {enum aux_ch aux_ch;enum intel_display_power_domain ddi_io_power_domain; bool tc_legacy_port:1;not related, but why do we add a hole in the struct on purpose?!?
The purpose was to group all the TypeC related fields at one spot. We could save some space gathering all the bools in this struct (release_cl2_override, tc_legacy_port) into a bool bitfield.
Quoted 90 lines
Quoted 90 lines
drivers/gpu/drm/i915/intel_drv.h +1
-1-enum tc_port_type tc_type; +enum tc_port_mode tc_mode; void (*write_infoframe)(struct intel_encoder *encoder, const struct intel_crtc_state *crtc_state,drivers/gpu/drm/i915/intel_tc.c +13
-17@@ -6,19 +6,18 @@#include "i915_drv.h" #include "intel_tc.h" -static const char *tc_type_name (enum tc_port_type type) +static const char *tc_port_mode_name (enum tc_port_mode mode) {static const char *const names[] = { - [TC_PORT_UNKNOWN ] ="unknown" , + [TC_PORT_TBT_ALT ] ="tbt-alt" , + [TC_PORT_DP_ALT ] ="dp-alt" , [TC_PORT_LEGACY ] ="legacy" , - [TC_PORT_TYPEC ] ="typec" , - [TC_PORT_TBT ] ="tbt" , }; -if (WARN_ON (type >=ARRAY_SIZE (names))) - type =TC_PORT_UNKNOWN ; +if (WARN_ON (mode >=ARRAY_SIZE (names))) + mode =TC_PORT_TBT_ALT ; -return names[type]; +return names[mode]; }int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port)@@ -28,7 +27,7 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port)intel_wakeref_t wakeref;u32 lane_info; -if (tc_port ==PORT_TC_NONE || dig_port->tc_type !=TC_PORT_TYPEC ) +if (dig_port->tc_mode !=TC_PORT_DP_ALT )return 4 ; lane_info =0 ;@@ -80,8 +79,8 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port)enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port);u32 val; -if (dig_port->tc_type !=TC_PORT_LEGACY && - dig_port->tc_type !=TC_PORT_TYPEC ) +if (dig_port->tc_mode !=TC_PORT_LEGACY && + dig_port->tc_mode !=TC_PORT_DP_ALT )return true; val =I915_READ (PORT_TX_DFLEXDPPMS );@@ -105,7 +104,7 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port)* Now we have to re-check the live state, in case the port recently * became disconnected. Not necessary for legacy mode. */ -if (dig_port->tc_type ==TC_PORT_TYPEC && +if (dig_port->tc_mode ==TC_PORT_DP_ALT && !(I915_READ (PORT_TX_DFLEXDPSP ) &TC_LIVE_STATE_TC (tc_port))) {DRM_DEBUG_KMS ("TC PHY %d sudden disconnect.\n" , tc_port);icl_tc_phy_disconnect (dig_port);@@ -124,15 +123,12 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port)struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); -if (dig_port->tc_type ==TC_PORT_UNKNOWN ) -return ; -/* * TBT disconnection flow is read the live status, what was done in * caller. */ -if (dig_port->tc_type ==TC_PORT_TYPEC || - dig_port->tc_type ==TC_PORT_LEGACY ) { +if (dig_port->tc_mode ==TC_PORT_DP_ALT || + dig_port->tc_mode ==TC_PORT_LEGACY ) {u32 val; val =I915_READ (PORT_TX_DFLEXDPCSSS );@@ -142,9 +138,9 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port)DRM_DEBUG_KMS ("Port %c TC type %s disconnected\n" ,port_name (dig_port->base.port), -tc_type_name (dig_port->tc_type)); +tc_port_mode_name (dig_port->tc_mode));
Quoted 4 lines
drivers/gpu/drm/i915/intel_tc.c void icl_tc_phy_disconnect(struct intel_digital_port *dig_port) · line 143
Quoted 2 lines
drivers/gpu/drm/i915/intel_tc.c +1
-1- dig_port->tc_type =TC_PORT_UNKNOWN ; + dig_port->tc_mode =TC_PORT_TBT_ALT ;humn... if this is what the hw has after reset,
Yes, IOW if we'd only connect/disconnect a TBT-Alt sink we wouldn't have to do anything to connect/disconnect the PHY (icl_tc_phy_connect() / icl_tc_phy_disconnect() would both become NOPs). That's unlike if we'd had only a DP-Alt/legacy sink where we have the TypeC specific programming steps to connect/disconnect the PHY.
Quoted 43 lines
then I think it covers my concern above.
Reviewed-by Lucas De Marchi <[email protected]>Lucas De Marchi
Quoted 36 lines
drivers/gpu/drm/i915/intel_tc.c +6
-10} static void icl_update_tc_port_type(struct drm_i915_private *dev_priv,@@ -152,26 +148,22 @@ static void icl_update_tc_port_type(struct drm_i915_private *dev_priv, bool is_legacy, bool is_typec, bool is_tbt) { enum port port = intel_dig_port->base.port; -enum tc_port_type old_type = intel_dig_port->tc_type; +enum tc_port_mode old_mode = intel_dig_port->tc_mode;WARN_ON (is_legacy + is_typec + is_tbt !=1 );if (is_legacy) - intel_dig_port->tc_type =TC_PORT_LEGACY ; + intel_dig_port->tc_mode =TC_PORT_LEGACY ;else if (is_typec) - intel_dig_port->tc_type =TC_PORT_TYPEC ; + intel_dig_port->tc_mode =TC_PORT_DP_ALT ;else if (is_tbt) - intel_dig_port->tc_type =TC_PORT_TBT ; + intel_dig_port->tc_mode =TC_PORT_TBT_ALT ;else return ; -/* Types are not supposed to be changed at runtime. */ -WARN_ON (old_type !=TC_PORT_UNKNOWN && - old_type != intel_dig_port->tc_type); - -if (old_type != intel_dig_port->tc_type) +if (old_mode != intel_dig_port->tc_mode)DRM_DEBUG_KMS ("Port %c has TC type %s\n" ,port_name (port), -tc_type_name (intel_dig_port->tc_type)); +tc_port_mode_name (intel_dig_port->tc_mode)); }
Quoted 7 lines
Quoted 7 lines
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 5/23 drm/i915: Don't enable the DDI-IO power in the TypeC TBT-alt mode
In reply to Imre DeakAccording to the spec we should not enable the DDI-IO power domain if the TypeC port is in the TBT-alt mode, so do that only in the other TypeC modes or for non-TypeC ports.
--- drivers/gpu/drm/i915/intel_ddi.c | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-)
drivers/gpu/drm/i915/intel_ddi.c +8 -3
@@ -3111,7 +3111,10 @@ static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder,intel_ddi_clk_select (encoder, crtc_state); -intel_display_power_get (dev_priv, dig_port->ddi_io_power_domain); +if (!intel_port_is_tc (dev_priv, port) || + dig_port->tc_mode !=TC_PORT_TBT_ALT ) +intel_display_power_get (dev_priv, + dig_port->ddi_io_power_domain);icl_program_mg_dp_mode (dig_port);icl_disable_phy_clock_gating (dig_port);
@@ -3293,8 +3296,10 @@ static void intel_ddi_post_disable_dp(struct intel_encoder *encoder,intel_edp_panel_vdd_on (intel_dp);intel_edp_panel_off (intel_dp); -intel_display_power_put_unchecked (dev_priv, - dig_port->ddi_io_power_domain); +if (!intel_port_is_tc (dev_priv, encoder->port) || + dig_port->tc_mode !=TC_PORT_TBT_ALT ) +intel_display_power_put_unchecked (dev_priv, + dig_port->ddi_io_power_domain);intel_ddi_clk_disable (encoder); }
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 05/23] drm/i915: Don't enable the DDI-IO power in the TypeC TBT-alt mode
Quoted 3 lines · Imre Deak
According to the spec we should not enable the DDI-IO power domain if the TypeC port is in the TBT-alt mode, so do that only in the other TypeC modes or for non-TypeC ports.
With:
BSpec: 22243
Quoted 41 lines
Cc Manasi Navare <[email protected]>Cc Anusha Srivatsa <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_ddi.c | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-)drivers/gpu/drm/i915/intel_ddi.c +4
-1@@ -3111,7 +3111,10 @@ static void intel_ddi_pre_enable_dp(structintel_encoder *encoder,intel_ddi_clk_select (encoder ,crtc_state ); -intel_display_power_get (dev_priv, dig_port- >ddi_io_power_domain); +if (!intel_port_is_tc (dev_priv, port) || + dig_port->tc_mode !=TC_PORT_TBT_ALT ) +intel_display_power_get (dev_priv, + dig_port->ddi_io_power_domain);drivers/gpu/drm/i915/intel_ddi.c +4
-2icl_program_mg_dp_mode (dig_port);icl_disable_phy_clock_gating (dig_port);@@ -3293,8 +3296,10 @@ static void intel_ddi_post_disable_dp(structintel_encoder *encoder,intel_edp_panel_vdd_on (intel_dp );intel_edp_panel_off (intel_dp); -intel_display_power_put_unchecked (dev_priv, - dig_port- >ddi_io_power_domain); +if (!intel_port_is_tc (dev_priv, encoder->port) || + dig_port->tc_mode !=TC_PORT_TBT_ALT ) +intel_display_power_put_unchecked (dev_priv, + dig_port- >ddi_io_power_domain);
Quoted 2 lines
intel_ddi_clk_disable(encoder);
}
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 6/23 drm/i915: Fix the TBT AUX power well enabling
In reply to Imre DeakFix the mapping from a TBT AUX power well index to the DP_AUX_CH_CTL register.
--- drivers/gpu/drm/i915/intel_display_power.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-)
drivers/gpu/drm/i915/intel_display_power.c +9 -2
@@ -442,16 +442,23 @@ icl_combo_phy_aux_power_well_disable(struct drm_i915_private *dev_priv,#define ICL_AUX_PW_TO_CH (pw_idx) \ ((pw_idx) - ICL_PW_CTL_IDX_AUX_A + AUX_CH_A) +#define ICL_TBT_AUX_PW_TO_CH (pw_idx) \ + ((pw_idx) - ICL_PW_CTL_IDX_AUX_TBT1 + AUX_CH_C) +static void icl_tc_phy_aux_power_well_enable (struct drm_i915_private *dev_priv,struct i915_power_well *power_well) { -enum aux_ch aux_ch =ICL_AUX_PW_TO_CH (power_well->desc->hsw.idx); +int pw_idx = power_well->desc->hsw.idx; +bool is_tbt = power_well->desc->hsw.is_tc_tbt; +enum aux_ch aux_ch;u32 val; + aux_ch = is_tbt ?ICL_TBT_AUX_PW_TO_CH (pw_idx) : +ICL_AUX_PW_TO_CH (pw_idx); val =I915_READ (DP_AUX_CH_CTL (aux_ch)); val &= ~DP_AUX_CH_CTL_TBT_IO ; -if (power_well->desc->hsw.is_tc_tbt) +if (is_tbt) val |=DP_AUX_CH_CTL_TBT_IO ;I915_WRITE (DP_AUX_CH_CTL (aux_ch), val);
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 06/23] drm/i915: Fix the TBT AUX power well enabling
Quoted 28 lines · Imre Deak
Fix the mapping from a TBT AUX power well index to the
DP_AUX_CH_CTLregister.Fixes c7375d9542f1 ("drm/i915: Configure AUX_CH_CTL when enablingthe AUX power domain")
Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_display_power.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-)drivers/gpu/drm/i915/intel_display_power.c +3
-0@@ -442,16 +442,23 @@ icl_combo_phy_aux_power_well_disable(structdrm_i915_private *dev_priv, #define ICL_AUX_PW_TO_CH(pw_idx) \ ((pw_idx) - ICL_PW_CTL_IDX_AUX_A + AUX_CH_A) +#define ICL_TBT_AUX_PW_TO_CH(pw_idx) \ + ((pw_idx) - ICL_PW_CTL_IDX_AUX_TBT1 + AUX_CH_C) +static void icl_tc_phy_aux_power_well_enable (struct drm_i915_private *dev_priv,struct i915_power_well *power_well)
drivers/gpu/drm/i915/intel_display_power.c icl_combo_phy_aux_power_well_disable(struct · line 460
Quoted 10 lines
drivers/gpu/drm/i915/intel_display_power.c +5
-1{ -enum aux_ch aux_ch =ICL_AUX_PW_TO_CH (power_well->desc- >hsw.idx); +int pw_idx = power_well->desc->hsw.idx; +bool is_tbt = power_well->desc->hsw.is_tc_tbt; +enum aux_ch aux_ch;u32 val; + aux_ch = is_tbt ?ICL_TBT_AUX_PW_TO_CH (pw_idx) : +ICL_AUX_PW_TO_CH (pw_idx);
Matches
drivers/gpu/drm/i915/intel_display_power.c icl_combo_phy_aux_power_well_disable(struct drm_i915_private *dev_priv, · line 462
Quoted 5 lines
drivers/gpu/drm/i915/intel_display_power.c +1
-1val =I915_READ (DP_AUX_CH_CTL (aux_ch)); val &= ~DP_AUX_CH_CTL_TBT_IO ; -if (power_well->desc->hsw.is_tc_tbt) +if (is_tbt) val |=DP_AUX_CH_CTL_TBT_IO ;
So this register needs to be set before the aux transaction?
Quoted 2 lines
I915_WRITE(DP_AUX_CH_CTL(aux_ch), val);
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 06/23] drm/i915: Fix the TBT AUX power well enabling
Quoted 44 lines · Jose
Quoted 28 lines · Imre Deak
Fix the mapping from a TBT AUX power well index to the
DP_AUX_CH_CTLregister.Fixes c7375d9542f1 ("drm/i915: Configure AUX_CH_CTL when enablingthe AUX power domain")
Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_display_power.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-)drivers/gpu/drm/i915/intel_display_power.c +3
-0@@ -442,16 +442,23 @@ icl_combo_phy_aux_power_well_disable(structdrm_i915_private *dev_priv, #define ICL_AUX_PW_TO_CH(pw_idx) \ ((pw_idx) - ICL_PW_CTL_IDX_AUX_A + AUX_CH_A) +#define ICL_TBT_AUX_PW_TO_CH(pw_idx) \ + ((pw_idx) - ICL_PW_CTL_IDX_AUX_TBT1 + AUX_CH_C) +static void icl_tc_phy_aux_power_well_enable (struct drm_i915_private *dev_priv,struct i915_power_well *power_well)drivers/gpu/drm/i915/intel_display_power.c icl_combo_phy_aux_power_well_disable(struct · line 460
Quoted 10 lines
drivers/gpu/drm/i915/intel_display_power.c +5
-1{ -enum aux_ch aux_ch =ICL_AUX_PW_TO_CH (power_well->desc- >hsw.idx); +int pw_idx = power_well->desc->hsw.idx; +bool is_tbt = power_well->desc->hsw.is_tc_tbt; +enum aux_ch aux_ch;u32 val; + aux_ch = is_tbt ?ICL_TBT_AUX_PW_TO_CH (pw_idx) : +ICL_AUX_PW_TO_CH (pw_idx);Matches
Reviewed-by José Roberto de Souza <[email protected]>
Quoted 7 lines
drivers/gpu/drm/i915/intel_display_power.c icl_combo_phy_aux_power_well_disable(struct drm_i915_private *dev_priv, · line 462
Quoted 5 lines
drivers/gpu/drm/i915/intel_display_power.c +1
-1val =I915_READ (DP_AUX_CH_CTL (aux_ch)); val &= ~DP_AUX_CH_CTL_TBT_IO ; -if (power_well->desc->hsw.is_tc_tbt) +if (is_tbt) val |=DP_AUX_CH_CTL_TBT_IO ;So this register needs to be set before the aux transaction?
Not only, based on bspec TypeC Programming (Index/21750) it needs to be set as part of the connect sequence; so whenever you need to enable this power well.
Quoted 3 lines
Quoted 3 lines
I915_WRITE(DP_AUX_CH_CTL(aux_ch), val);
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 7/23 drm/i915: Use the correct AUX power domain in TypeC TBT-alt mode
In reply to Imre DeakIn the TypeC TBT-alt port mode we must use the TBT AUX power domain, fix that.
--- drivers/gpu/drm/i915/intel_display.c | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)
drivers/gpu/drm/i915/intel_display.c +19 -0
@@ -6609,6 +6609,25 @@ enum intel_display_power_domain intel_port_to_power_domain(enum port port)enum intel_display_power_domain intel_aux_power_domain (struct intel_digital_port *dig_port) { +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); + +if (intel_port_is_tc (dev_priv, dig_port->base.port) && + dig_port->tc_mode ==TC_PORT_TBT_ALT ) { +switch (dig_port->aux_ch) { +case AUX_CH_C : +return POWER_DOMAIN_AUX_TBT1 ; +case AUX_CH_D : +return POWER_DOMAIN_AUX_TBT2 ; +case AUX_CH_E : +return POWER_DOMAIN_AUX_TBT3 ; +case AUX_CH_F : +return POWER_DOMAIN_AUX_TBT4 ; +default : +MISSING_CASE (dig_port->aux_ch); +return POWER_DOMAIN_AUX_TBT1 ; + } + } +switch (dig_port->aux_ch) {case AUX_CH_A :return POWER_DOMAIN_AUX_A ;
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 07/23] drm/i915: Use the correct AUX power domain in TypeC TBT-alt mode
Quoted 29 lines · Imre Deak
In the TypeC TBT-alt port mode we must use the TBT AUX power domain, fix that.
Cc Manasi Navare <[email protected]>Cc Anusha Srivatsa <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_display.c | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)drivers/gpu/drm/i915/intel_display.c +8
-0@@ -6609,6 +6609,25 @@ enum intel_display_power_domain intel_port_to_power_domain(enum port port) enum intel_display_power_domainintel_aux_power_domain (struct intel_digital_port *dig_port) { +struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev); + +if (intel_port_is_tc (dev_priv, dig_port->base.port) && + dig_port->tc_mode ==TC_PORT_TBT_ALT ) { +switch (dig_port->aux_ch) { +case AUX_CH_C : +return POWER_DOMAIN_AUX_TBT1 ; +case AUX_CH_D :
drivers/gpu/drm/i915/intel_display.c enum intel_display_power_domain · line 6631
Quoted 10 lines
drivers/gpu/drm/i915/intel_display.c +10
-0+return POWER_DOMAIN_AUX_TBT2 ; +case AUX_CH_E : +return POWER_DOMAIN_AUX_TBT3 ; +case AUX_CH_F : +return POWER_DOMAIN_AUX_TBT4 ; +default : +MISSING_CASE (dig_port->aux_ch); +return POWER_DOMAIN_AUX_TBT1 ; + } + }
I would go by:
return dig_port->aux_ch - AUX_CH_C + POWER_DOMAIN_AUX_TBT1;
but that works too.
drivers/gpu/drm/i915/intel_display.c enum intel_display_power_domain intel_port_to_power_domain(enum port port) · line 6633
Quoted 4 lines
drivers/gpu/drm/i915/intel_display.c +1
-0+switch (dig_port->aux_ch) {drivers/gpu/drm/i915/intel_display.c +0
-0case AUX_CH_A :return POWER_DOMAIN_AUX_A ;
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 8/23 drm/i915: Unify the TypeC port notation in debug/error messages
In reply to Imre DeakUnify the TypeC port notation in log messages, so that it matches the spec. For instance the first ICL TypeC port will read as 'Port C/TC#1'.
--- drivers/gpu/drm/i915/intel_tc.c | 41 +++++++++++++++++++++++++++------ 1 file changed, 34 insertions(+), 7 deletions(-)
drivers/gpu/drm/i915/intel_tc.c +34 -7
@@ -6,6 +6,29 @@#include "i915_drv.h" #include "intel_tc.h" +static enum port intel_tc_port_to_port (struct drm_i915_private *dev_priv, +enum tc_port tc_port) +{ +return tc_port +PORT_C ; +} + +static const char *tc_port_name (struct drm_i915_private *dev_priv, +enum tc_port tc_port) +{ +static char port_names[I915_MAX_TC_PORTS ][8 ]; + +if (WARN_ON (INTEL_GEN (dev_priv) <11 || + (unsigned int )tc_port >=I915_MAX_TC_PORTS )) + tc_port =PORT_TC1 ; + +snprintf (&port_names[tc_port][0 ],sizeof (port_names[tc_port]), +"%c/TC#%d" , +port_name (intel_tc_port_to_port (dev_priv, tc_port)), + tc_port +1 ); + +return port_names[tc_port]; +} +static const char *tc_port_mode_name (enum tc_port_mode mode) {static const char *const names[] = {
@@ -85,7 +108,8 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port) val =I915_READ (PORT_TX_DFLEXDPPMS );if (!(val &DP_PHY_MODE_STATUS_COMPLETED (tc_port))) { -DRM_DEBUG_KMS ("DP PHY for TC port %d not ready\n" , tc_port); +DRM_DEBUG_KMS ("Port %s: PHY not ready\n" , +tc_port_name (dev_priv, tc_port));WARN_ON (dig_port->tc_legacy_port);return false; }
@@ -106,7 +130,8 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port)*/ if (dig_port->tc_mode ==TC_PORT_DP_ALT && !(I915_READ (PORT_TX_DFLEXDPSP ) &TC_LIVE_STATE_TC (tc_port))) { -DRM_DEBUG_KMS ("TC PHY %d sudden disconnect.\n" , tc_port); +DRM_DEBUG_KMS ("Port %s: PHY sudden disconnect\n" , +tc_port_name (dev_priv, tc_port));icl_tc_phy_disconnect (dig_port);return false; }
@@ -136,8 +161,8 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port)I915_WRITE (PORT_TX_DFLEXDPCSSS , val); } -DRM_DEBUG_KMS ("Port %c TC type %s disconnected\n" , -port_name (dig_port->base.port), +DRM_DEBUG_KMS ("Port %s: mode %s disconnected\n" , +tc_port_name (dev_priv, tc_port),tc_port_mode_name (dig_port->tc_mode)); dig_port->tc_mode =TC_PORT_TBT_ALT ;
@@ -162,7 +187,9 @@ static void icl_update_tc_port_type(struct drm_i915_private *dev_priv,return ;if (old_mode != intel_dig_port->tc_mode) -DRM_DEBUG_KMS ("Port %c has TC type %s\n" ,port_name (port), +DRM_DEBUG_KMS ("Port %s: port has mode %s\n" , +tc_port_name (dev_priv, +intel_port_to_tc (dev_priv, port)),tc_port_mode_name (intel_dig_port->tc_mode)); }
@@ -191,8 +218,8 @@ bool intel_tc_port_connected(struct intel_digital_port *dig_port)*/ if (!dig_port->tc_legacy_port &&I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) { -DRM_ERROR ("VBT incorrectly claims port %c is not TypeC legacy\n" , -port_name (port)); +DRM_ERROR ("Port %s: VBT incorrectly claims port is not TypeC legacy\n" , +tc_port_name (dev_priv, tc_port)); dig_port->tc_legacy_port = true; } is_legacy = dig_port->tc_legacy_port;
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 08/23] drm/i915: Unify the TypeC port notation in debug/error messages
Quoted 27 lines · Imre Deak
Unify the TypeC port notation in log messages, so that it matches the spec. For instance the first ICL TypeC port will read as 'Port C/TC#1'.
Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_tc.c | 41 +++++++++++++++++++++++++++-- ---- 1 file changed, 34 insertions(+), 7 deletions(-)drivers/gpu/drm/i915/intel_tc.c +4
-0@@ -6,6 +6,29 @@#include "i915_drv.h" #include "intel_tc.h" +static enum port intel_tc_port_to_port (struct drm_i915_private *dev_priv, +enum tc_port tc_port) +{ +return tc_port +PORT_C ;
drivers/gpu/drm/i915/intel_tc.c line 23
Quoted 10 lines
drivers/gpu/drm/i915/intel_tc.c +10
-0+} + +static const char *tc_port_name (struct drm_i915_private *dev_priv, +enum tc_port tc_port) +{ +static char port_names[I915_MAX_TC_PORTS ][8 ]; + +if (WARN_ON (INTEL_GEN (dev_priv) <11 || + (unsigned int )tc_port >=I915_MAX_TC_PORTS )) + tc_port =PORT_TC1 ;
Why no WARN_ON on the tc_port >= I915_MAX_TC_PORTS?
drivers/gpu/drm/i915/intel_tc.c line 27
Quoted 5 lines
drivers/gpu/drm/i915/intel_tc.c +5
-0+ +snprintf (&port_names[tc_port][0 ],sizeof (port_names[tc_port]), +"%c/TC#%d" , +port_name (intel_tc_port_to_port (dev_priv, tc_port)), + tc_port +1 );
Maybe do it only once for each port?
if (port_names[tc_port][0])
return port_names[tc_port];
snprintf(&port_names[tc_port], sizeof....
Other the above:
Quoted 70 lines
drivers/gpu/drm/i915/intel_tc.c +4
-0+ +return port_names[tc_port]; +} +static const char *tc_port_mode_name (enum tc_port_mode mode) {drivers/gpu/drm/i915/intel_tc.c +2
-1static const char *const names[] = {@@ -85,7 +108,8 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port) val =I915_READ (PORT_TX_DFLEXDPPMS );if (!(val &DP_PHY_MODE_STATUS_COMPLETED (tc_port))) { -DRM_DEBUG_KMS ("DP PHY for TC port %d not ready\n" , tc_port); +DRM_DEBUG_KMS ("Port %s: PHY not ready\n" , +tc_port_name (dev_priv, tc_port));WARN_ON (dig_port->tc_legacy_port);drivers/gpu/drm/i915/intel_tc.c +2
-1return false; }@@ -106,7 +130,8 @@ static bool icl_tc_phy_connect(structintel_digital_port *dig_port) */ if (dig_port->tc_mode ==TC_PORT_DP_ALT && !(I915_READ (PORT_TX_DFLEXDPSP ) &TC_LIVE_STATE_TC (tc_port))) { -DRM_DEBUG_KMS ("TC PHY %d sudden disconnect.\n" , tc_port); +DRM_DEBUG_KMS ("Port %s: PHY sudden disconnect\n" , +tc_port_name (dev_priv, tc_port));drivers/gpu/drm/i915/intel_tc.c +2
-2icl_tc_phy_disconnect (dig_port);return false; }@@ -136,8 +161,8 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port)I915_WRITE (PORT_TX_DFLEXDPCSSS ,val ); } -DRM_DEBUG_KMS ("Port %c TC type %s disconnected\n" , -port_name (dig_port->base.port), +DRM_DEBUG_KMS ("Port %s: mode %s disconnected\n" , +tc_port_name (dev_priv, tc_port),tc_port_mode_name (dig_port->tc_mode));drivers/gpu/drm/i915/intel_tc.c +3
-1dig_port->tc_mode =TC_PORT_TBT_ALT ;@@ -162,7 +187,9 @@ static void icl_update_tc_port_type(structdrm_i915_private *dev_priv, return;if (old_mode != intel_dig_port->tc_mode) -DRM_DEBUG_KMS ("Port %c has TC type %s\n" ,port_name (port), + DRM_DEBUG_KMS("Port %s: port has mode %s\n", + tc_port_name(dev_priv, + intel_port_to_tc(dev_priv, port)),tc_port_mode_name(intel_dig_port-
Quoted 1 line
tc_mode));}
drivers/gpu/drm/i915/intel_tc.c +2
-2@@ -191,8 +218,8 @@ bool intel_tc_port_connected(structintel_digital_port *dig_port) */ if (!dig_port->tc_legacy_port &&I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) { -DRM_ERROR ("VBT incorrectly claims port %c is not TypeC legacy\n", -port_name (port)); + DRM_ERROR("Port %s: VBT incorrectly claims port is not TypeC legacy\n", +tc_port_name (dev_priv ,tc_port ));
drivers/gpu/drm/i915/intel_tc.c bool intel_tc_port_connected(struct intel_digital_port *dig_port) · line 225
Quoted 3 lines
drivers/gpu/drm/i915/intel_tc.c +0
-0dig_port->tc_legacy_port = true; } is_legacy = dig_port->tc_legacy_port;
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 08/23] drm/i915: Unify the TypeC port notation in debug/error messages
Quoted 32 lines · Jose
Quoted 31 lines · Imre Deak
Unify the TypeC port notation in log messages, so that it matches the spec. For instance the first ICL TypeC port will read as 'Port C/TC#1'.
Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_tc.c | 41 +++++++++++++++++++++++++++-- ---- 1 file changed, 34 insertions(+), 7 deletions(-)drivers/gpu/drm/i915/intel_tc.c +8
-0@@ -6,6 +6,29 @@#include "i915_drv.h" #include "intel_tc.h" +static enum port intel_tc_port_to_port (struct drm_i915_private *dev_priv, +enum tc_port tc_port) +{ +return tc_port +PORT_C ; +} + +static const char *tc_port_name (struct drm_i915_private *dev_priv, +enum tc_port tc_port)
Quoted 8 lines
drivers/gpu/drm/i915/intel_tc.c line 22
Quoted 6 lines
drivers/gpu/drm/i915/intel_tc.c +6
-0+{ +static char port_names[I915_MAX_TC_PORTS ][8 ]; + +if (WARN_ON (INTEL_GEN (dev_priv) <11 || + (unsigned int )tc_port >=I915_MAX_TC_PORTS )) + tc_port =PORT_TC1 ;Why no
WARN_ONon thetc_port>=I915_MAX_TC_PORTS?
Hm, do you mean a seaparate WARN_ON()?
Quoted 11 lines
drivers/gpu/drm/i915/intel_tc.c line 27
Quoted 6 lines
drivers/gpu/drm/i915/intel_tc.c +5
-0+ +snprintf (&port_names[tc_port][0 ],sizeof (port_names[tc_port]), +"%c/TC#%d" , +port_name (intel_tc_port_to_port (dev_priv, tc_port)), + tc_port +1 );Maybe do it only once for each port?
if (port_names[tc_port][0])
return port_names[tc_port];
I thought why not keep it as simple as possible (not really performance critical), but your version makes it clearer to the reader what the logic is (static array), so can change it.
Quoted 66 lines
snprintf(&port_names[tc_port], sizeof....
Other the above:
Reviewed-by José Roberto de Souza <[email protected]>Quoted 59 lines
drivers/gpu/drm/i915/intel_tc.c +4
-0+ +return port_names[tc_port]; +} +static const char *tc_port_mode_name (enum tc_port_mode mode) {drivers/gpu/drm/i915/intel_tc.c +2
-1static const char *const names[] = {@@ -85,7 +108,8 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port) val =I915_READ (PORT_TX_DFLEXDPPMS );if (!(val &DP_PHY_MODE_STATUS_COMPLETED (tc_port))) { -DRM_DEBUG_KMS ("DP PHY for TC port %d not ready\n" , tc_port); +DRM_DEBUG_KMS ("Port %s: PHY not ready\n" , +tc_port_name (dev_priv, tc_port));WARN_ON (dig_port->tc_legacy_port);drivers/gpu/drm/i915/intel_tc.c +2
-1return false; }@@ -106,7 +130,8 @@ static bool icl_tc_phy_connect(structintel_digital_port *dig_port) */ if (dig_port->tc_mode ==TC_PORT_DP_ALT && !(I915_READ (PORT_TX_DFLEXDPSP ) &TC_LIVE_STATE_TC (tc_port))) { -DRM_DEBUG_KMS ("TC PHY %d sudden disconnect.\n" , tc_port); +DRM_DEBUG_KMS ("Port %s: PHY sudden disconnect\n" , +tc_port_name (dev_priv, tc_port));drivers/gpu/drm/i915/intel_tc.c +2
-2icl_tc_phy_disconnect (dig_port);return false; }@@ -136,8 +161,8 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port)I915_WRITE (PORT_TX_DFLEXDPCSSS ,val ); } -DRM_DEBUG_KMS ("Port %c TC type %s disconnected\n" , -port_name (dig_port->base.port), +DRM_DEBUG_KMS ("Port %s: mode %s disconnected\n" , +tc_port_name (dev_priv, tc_port),tc_port_mode_name (dig_port->tc_mode));drivers/gpu/drm/i915/intel_tc.c +3
-1dig_port->tc_mode =TC_PORT_TBT_ALT ;@@ -162,7 +187,9 @@ static void icl_update_tc_port_type(structdrm_i915_private *dev_priv, return;if (old_mode != intel_dig_port->tc_mode) -DRM_DEBUG_KMS ("Port %c has TC type %s\n" ,port_name (port), + DRM_DEBUG_KMS("Port %s: port has mode %s\n", + tc_port_name(dev_priv, + intel_port_to_tc(dev_priv, port)),tc_port_mode_name(intel_dig_port-
Quoted 1 line
tc_mode));}
Quoted 14 lines
Quoted 11 lines
drivers/gpu/drm/i915/intel_tc.c +2
-2@@ -191,8 +218,8 @@ bool intel_tc_port_connected(structintel_digital_port *dig_port) */ if (!dig_port->tc_legacy_port &&I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) { -DRM_ERROR ("VBT incorrectly claims port %c is not TypeC legacy\n", -port_name (port)); + DRM_ERROR("Port %s: VBT incorrectly claims port is not TypeC legacy\n", +tc_port_name (dev_priv ,tc_port ));drivers/gpu/drm/i915/intel_tc.c bool intel_tc_port_connected(struct intel_digital_port *dig_port) · line 225
Quoted 3 lines
drivers/gpu/drm/i915/intel_tc.c +0
-0dig_port->tc_legacy_port = true; } is_legacy = dig_port->tc_legacy_port;
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 08/23] drm/i915: Unify the TypeC port notation in debug/error messages
Quoted 45 lines · Imre Deak
Quoted 35 lines · Jose
Quoted 34 lines · Imre Deak
Unify the TypeC port notation in log messages, so that it matches the
spec. For instance the first ICL TypeC port will read as 'Port C/TC#1'.Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_tc.c | 41 +++++++++++++++++++++++++++-- ---- 1 file changed, 34 insertions(+), 7 deletions(-)drivers/gpu/drm/i915/intel_tc.c +8
-0@@ -6,6 +6,29 @@#include "i915_drv.h" #include "intel_tc.h" +static enum port intel_tc_port_to_port (struct drm_i915_private *dev_priv, +enum tc_port tc_port) +{ +return tc_port +PORT_C ; +} + +static const char *tc_port_name (struct drm_i915_private *dev_priv, +enum tc_port tc_port)Quoted 8 lines
drivers/gpu/drm/i915/intel_tc.c line 22
Quoted 6 lines
drivers/gpu/drm/i915/intel_tc.c +6
-0+{ +static char port_names[I915_MAX_TC_PORTS ][8 ]; + +if (WARN_ON (INTEL_GEN (dev_priv) <11 || + (unsigned int )tc_port >=I915_MAX_TC_PORTS )) + tc_port =PORT_TC1 ;Why no
WARN_ONon thetc_port>=I915_MAX_TC_PORTS?
Quoted 1 line
Hm, do you mean a seaparate
WARN_ON()?
Oh I misread the parentheses, it is right.
Quoted 82 lines
Quoted 11 lines
drivers/gpu/drm/i915/intel_tc.c line 27
Quoted 6 lines
drivers/gpu/drm/i915/intel_tc.c +5
-0+ +snprintf (&port_names[tc_port][0 ],sizeof (port_names[tc_port]), +"%c/TC#%d" , +port_name (intel_tc_port_to_port (dev_priv, tc_port)), + tc_port +1 );Maybe do it only once for each port?
if (port_names[tc_port][0])
return port_names[tc_port];I thought why not keep it as simple as possible (not really performance
critical), but your version makes it clearer to the reader what the logic is (static array), so can change it.Quoted 65 lines
snprintf(&port_names[tc_port], sizeof....
Other the above:
Reviewed-by José Roberto de Souza <[email protected]>Quoted 59 lines
drivers/gpu/drm/i915/intel_tc.c +4
-0+ +return port_names[tc_port]; +} +static const char *tc_port_mode_name (enum tc_port_mode mode){
drivers/gpu/drm/i915/intel_tc.c +2
-1static const char *const names[] = {@@ -85,7 +108,8 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port) val =I915_READ (PORT_TX_DFLEXDPPMS );if (!(val &DP_PHY_MODE_STATUS_COMPLETED (tc_port))) { -DRM_DEBUG_KMS ("DP PHY for TC port %d not ready\n" , tc_port); +DRM_DEBUG_KMS ("Port %s: PHY not ready\n" , +tc_port_name (dev_priv, tc_port));WARN_ON (dig_port->tc_legacy_port);drivers/gpu/drm/i915/intel_tc.c +2
-1return false; }@@ -106,7 +130,8 @@ static bool icl_tc_phy_connect(structintel_digital_port *dig_port) */ if (dig_port->tc_mode ==TC_PORT_DP_ALT && !(I915_READ (PORT_TX_DFLEXDPSP ) &TC_LIVE_STATE_TC (tc_port))) { -DRM_DEBUG_KMS ("TC PHY %d sudden disconnect.\n" , tc_port); +DRM_DEBUG_KMS ("Port %s: PHY sudden disconnect\n" , +tc_port_name (dev_priv, tc_port));drivers/gpu/drm/i915/intel_tc.c +2
-2icl_tc_phy_disconnect (dig_port);return false; }@@ -136,8 +161,8 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port)I915_WRITE (PORT_TX_DFLEXDPCSSS ,val ); } -DRM_DEBUG_KMS ("Port %c TC type %s disconnected\n" , -port_name (dig_port->base.port), +DRM_DEBUG_KMS ("Port %s: mode %s disconnected\n" , +tc_port_name (dev_priv, tc_port),tc_port_mode_name (dig_port->tc_mode));drivers/gpu/drm/i915/intel_tc.c +3
-1dig_port->tc_mode =TC_PORT_TBT_ALT ;@@ -162,7 +187,9 @@ static void icl_update_tc_port_type(structdrm_i915_private *dev_priv, return;if (old_mode != intel_dig_port->tc_mode) -DRM_DEBUG_KMS ("Port %c has TC type %s\n" ,port_name (port), + DRM_DEBUG_KMS("Port %s: port has mode %s\n", + tc_port_name(dev_priv, + intel_port_to_tc(dev_priv, port)),tc_port_mode_name(intel_dig_port-
Quoted 1 line
tc_mode));}
Quoted 14 lines
Quoted 6 lines
Quoted 6 lines
drivers/gpu/drm/i915/intel_tc.c +0
-1@@ -191,8 +218,8 @@ bool intel_tc_port_connected(structintel_digital_port *dig_port) */ if (!dig_port->tc_legacy_port &&I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) { - DRM_ERROR("VBT incorrectly claims port %c is not TypeCQuoted 8 lines
drivers/gpu/drm/i915/intel_tc.c bool intel_tc_port_connected(struct intel_digital_port *dig_port) · line 225
Quoted 8 lines
drivers/gpu/drm/i915/intel_tc.c +2
-1legacy\n", - port_name(port)); + DRM_ERROR("Port %s: VBT incorrectly claims port is not TypeC legacy\n", +tc_port_name (dev_priv ,tc_port ));drivers/gpu/drm/i915/intel_tc.c +0
-0dig_port->tc_legacy_port = true; } is_legacy = dig_port->tc_legacy_port;
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 08/23] drm/i915: Unify the TypeC port notation in debug/error messages
In reply to Imre DeakQuoted 42 lines · Imre Deak
Quoted 32 lines · Jose
Quoted 31 lines · Imre Deak
Unify the TypeC port notation in log messages, so that it matches the spec. For instance the first ICL TypeC port will read as 'Port C/TC#1'.
Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_tc.c | 41 +++++++++++++++++++++++++++-- ---- 1 file changed, 34 insertions(+), 7 deletions(-)drivers/gpu/drm/i915/intel_tc.c +8
-0@@ -6,6 +6,29 @@#include "i915_drv.h" #include "intel_tc.h" +static enum port intel_tc_port_to_port (struct drm_i915_private *dev_priv, +enum tc_port tc_port) +{ +return tc_port +PORT_C ; +} + +static const char *tc_port_name (struct drm_i915_private *dev_priv, +enum tc_port tc_port)Quoted 8 lines
drivers/gpu/drm/i915/intel_tc.c line 22
Quoted 6 lines
drivers/gpu/drm/i915/intel_tc.c +6
-0+{ +static char port_names[I915_MAX_TC_PORTS ][8 ]; + +if (WARN_ON (INTEL_GEN (dev_priv) <11 || + (unsigned int )tc_port >=I915_MAX_TC_PORTS )) + tc_port =PORT_TC1 ;Why no
WARN_ONon thetc_port>=I915_MAX_TC_PORTS?
Quoted 1 line
Hm, do you mean a seaparate
WARN_ON()?
Well, at least it's misindented, I can fix that.
Quoted 93 lines
Quoted 10 lines
drivers/gpu/drm/i915/intel_tc.c line 27
Quoted 7 lines
drivers/gpu/drm/i915/intel_tc.c +5
-0+ +snprintf (&port_names[tc_port][0 ],sizeof (port_names[tc_port]), +"%c/TC#%d" , +port_name (intel_tc_port_to_port (dev_priv, tc_port)), + tc_port +1 );Maybe do it only once for each port?
Quoted 2 lines
if (port_names[tc_port][0])
return port_names[tc_port];I thought why not keep it as simple as possible (not really performance critical), but your version makes it clearer to the reader what the logic is (static array), so can change it.
Quoted 76 lines
snprintf(&port_names[tc_port], sizeof....
Other the above:
Reviewed-by José Roberto de Souza <[email protected]>Quoted 69 lines
drivers/gpu/drm/i915/intel_tc.c +4
-0+ +return port_names[tc_port]; +} +static const char *tc_port_mode_name (enum tc_port_mode mode) {drivers/gpu/drm/i915/intel_tc.c +2
-1static const char *const names[] = {@@ -85,7 +108,8 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port) val =I915_READ (PORT_TX_DFLEXDPPMS );if (!(val &DP_PHY_MODE_STATUS_COMPLETED (tc_port))) { -DRM_DEBUG_KMS ("DP PHY for TC port %d not ready\n" , tc_port); +DRM_DEBUG_KMS ("Port %s: PHY not ready\n" , +tc_port_name (dev_priv, tc_port));WARN_ON (dig_port->tc_legacy_port);drivers/gpu/drm/i915/intel_tc.c +2
-1return false; }@@ -106,7 +130,8 @@ static bool icl_tc_phy_connect(structintel_digital_port *dig_port) */ if (dig_port->tc_mode ==TC_PORT_DP_ALT && !(I915_READ (PORT_TX_DFLEXDPSP ) &TC_LIVE_STATE_TC (tc_port))) { -DRM_DEBUG_KMS ("TC PHY %d sudden disconnect.\n" , tc_port); +DRM_DEBUG_KMS ("Port %s: PHY sudden disconnect\n" , +tc_port_name (dev_priv, tc_port));drivers/gpu/drm/i915/intel_tc.c +2
-2icl_tc_phy_disconnect (dig_port);return false; }@@ -136,8 +161,8 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port)I915_WRITE (PORT_TX_DFLEXDPCSSS ,val ); } -DRM_DEBUG_KMS ("Port %c TC type %s disconnected\n" , -port_name (dig_port->base.port), +DRM_DEBUG_KMS ("Port %s: mode %s disconnected\n" , +tc_port_name (dev_priv, tc_port),tc_port_mode_name (dig_port->tc_mode));drivers/gpu/drm/i915/intel_tc.c +3
-1dig_port->tc_mode =TC_PORT_TBT_ALT ;@@ -162,7 +187,9 @@ static void icl_update_tc_port_type(structdrm_i915_private *dev_priv, return;if (old_mode != intel_dig_port->tc_mode) -DRM_DEBUG_KMS ("Port %c has TC type %s\n" ,port_name (port), + DRM_DEBUG_KMS("Port %s: port has mode %s\n", + tc_port_name(dev_priv, + intel_port_to_tc(dev_priv, port)),tc_port_mode_name(intel_dig_port-
Quoted 1 line
tc_mode));}
drivers/gpu/drm/i915/intel_tc.c +1
-2@@ -191,8 +218,8 @@ bool intel_tc_port_connected(structintel_digital_port *dig_port) */ if (!dig_port->tc_legacy_port &&I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) { -DRM_ERROR ("VBT incorrectly claims port %c is not TypeC legacy\n", -port_name (port)); + DRM_ERROR("Port %s: VBT incorrectly claims port is not TypeC legacy\n",
Quoted 8 lines
Quoted 4 lines
drivers/gpu/drm/i915/intel_tc.c bool intel_tc_port_connected(struct intel_digital_port *dig_port) · line 225
Quoted 4 lines
drivers/gpu/drm/i915/intel_tc.c +1
-0+ tc_port_name(dev_priv, tc_port));drivers/gpu/drm/i915/intel_tc.c +0
-0dig_port->tc_legacy_port = true; } is_legacy = dig_port->tc_legacy_port;_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 9/23 drm/i915: Factor out common parts from TypeC port handling functions
In reply to Imre DeakFactor out helpers reading/parsing the TypeC specific registers, making current users of them clearer and letting us use them later.
While at it also:
- Simplify icl_tc_phy_connect() with an early return in legacy mode.
- Simplify the live status check using one bitmask for all HPD bits.
- Remove a micro-optimisation of the repeated safe-mode clearing.
- Make sure we fix the legacy port flag in all cases.
Except for the last two, no functional changes.
--- drivers/gpu/drm/i915/intel_ddi.c | 5 +- drivers/gpu/drm/i915/intel_tc.c | 166 +++++++++++++++++++------------ drivers/gpu/drm/i915/intel_tc.h | 1 + 3 files changed, 103 insertions(+), 69 deletions(-)
drivers/gpu/drm/i915/intel_ddi.c +1 -4
@@ -2983,7 +2983,6 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port) {struct drm_i915_private *dev_priv =to_i915 (intel_dig_port->base.base.dev);enum port port = intel_dig_port->base.port; -enum tc_port tc_port =intel_port_to_tc (dev_priv, port);u32 ln0, ln1, lane_info;if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT )
@@ -2997,9 +2996,7 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port) ln0 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |MG_DP_MODE_CFG_DP_X2_MODE ); ln1 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |MG_DP_MODE_CFG_DP_X2_MODE ); - lane_info = (I915_READ (PORT_TX_DFLEXDPSP ) & -DP_LANE_ASSIGNMENT_MASK (tc_port)) >> -DP_LANE_ASSIGNMENT_SHIFT (tc_port); + lane_info =intel_tc_port_get_lane_info (intel_dig_port);switch (lane_info) {case 0x1 :
drivers/gpu/drm/i915/intel_tc.c +101 -65
246 lines not on this page · raw message
drivers/gpu/drm/i915/intel_tc.h +1 -0
@@ -8,6 +8,7 @@ struct intel_digital_port;void icl_tc_phy_disconnect (struct intel_digital_port *dig_port);bool intel_tc_port_connected (struct intel_digital_port *dig_port); +u32 intel_tc_port_get_lane_info (struct intel_digital_port *dig_port);int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port);#endif /* __INTEL_TC_H__ */
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Jani Nikula
maintainerRe: [PATCH 09/23] drm/i915: Factor out common parts from TypeC port handling functions
Quoted 49 lines · Imre Deak
Factor out helpers reading/parsing the TypeC specific registers, making current users of them clearer and letting us use them later.
While at it also:
- Simplifyicl_tc_phy_connect()with an early return in legacy mode.
- Simplify the live status check using one bitmask for all HPD bits.
- Remove a micro-optimisation of the repeated safe-mode clearing.
- Make sure we fix the legacy port flag in all cases.Except for the last two, no functional changes.
Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_ddi.c | 5 +- drivers/gpu/drm/i915/intel_tc.c | 166 +++++++++++++++++++------------ drivers/gpu/drm/i915/intel_tc.h | 1 + 3 files changed, 103 insertions(+), 69 deletions(-)drivers/gpu/drm/i915/intel_ddi.c +1
-4@@ -2983,7 +2983,6 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port) {struct drm_i915_private *dev_priv =to_i915 (intel_dig_port->base.base.dev);enum port port = intel_dig_port->base.port; -enum tc_port tc_port =intel_port_to_tc (dev_priv, port);u32 ln0, ln1, lane_info;if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT )@@ -2997,9 +2996,7 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port) ln0 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |MG_DP_MODE_CFG_DP_X2_MODE ); ln1 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |MG_DP_MODE_CFG_DP_X2_MODE ); - lane_info = (I915_READ (PORT_TX_DFLEXDPSP ) & -DP_LANE_ASSIGNMENT_MASK (tc_port)) >> -DP_LANE_ASSIGNMENT_SHIFT (tc_port); + lane_info =intel_tc_port_get_lane_info (intel_dig_port);switch (lane_info) {case 0x1 :drivers/gpu/drm/i915/intel_tc.c +0
-0
drivers/gpu/drm/i915/intel_tc.c static const char *tc_port_mode_name(enum tc_port_mode mode) · line 50
Quoted 9 lines
drivers/gpu/drm/i915/intel_tc.c +2
-1@@ -43,10 +43,19 @@ static const char *tc_port_mode_name(enum tc_port_mode mode)return names[mode]; } -int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port) +u32 intel_tc_port_get_lane_info (struct intel_digital_port *dig_port) {struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +u32 lane_info =I915_READ (PORT_TX_DFLEXDPSP );
Please don't do register reads in declarations. Ditto below.
Quoted 254 lines
drivers/gpu/drm/i915/intel_tc.c +99
-64+ +return (lane_info &DP_LANE_ASSIGNMENT_MASK (tc_port)) >> +DP_LANE_ASSIGNMENT_SHIFT (tc_port); +} + +int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);intel_wakeref_t wakeref;u32 lane_info;@@ -55,9 +64,7 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) lane_info =0 ;with_intel_display_power (dev_priv,POWER_DOMAIN_DISPLAY_CORE , wakeref) - lane_info = (I915_READ(PORT_TX_DFLEXDPSP) & -DP_LANE_ASSIGNMENT_MASK (tc_port)) >> -DP_LANE_ASSIGNMENT_SHIFT (tc_port); + lane_info = intel_tc_port_get_lane_info(dig_port);switch (lane_info) {default :@@ -75,6 +82,69 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) } } +static void tc_port_fixup_legacy_flag (struct intel_digital_port *dig_port, +u32 live_status_mask) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +u32 valid_hpd_mask = dig_port->tc_legacy_port ?BIT (TC_PORT_LEGACY ) : + ~BIT (TC_PORT_LEGACY ); + +if (!(live_status_mask & ~valid_hpd_mask)) +return ; + +/* If live status mismatches the VBT flag, trust the live status. */ +DRM_ERROR ("Port %s: live status %08x mismatches the legacy port flag, fix flag\n" , +tc_port_name (dev_priv, tc_port), live_status_mask); + + dig_port->tc_legacy_port = !dig_port->tc_legacy_port; +} + +static u32 tc_port_live_status_mask (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +u32 val =I915_READ (PORT_TX_DFLEXDPSP ); +u32 mask =0 ; + +if (val &TC_LIVE_STATE_TBT (tc_port)) + mask |=BIT (TC_PORT_TBT_ALT ); +if (val &TC_LIVE_STATE_TC (tc_port)) + mask |=BIT (TC_PORT_DP_ALT ); + +if (I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) + mask |=BIT (TC_PORT_LEGACY ); + +/* The sink can be connected only in a single mode. */ +if (!WARN_ON (hweight32 (mask) >1 )) +tc_port_fixup_legacy_flag (dig_port, mask); + +return mask; +} + +static bool icl_tc_phy_status_complete (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); + +return I915_READ (PORT_TX_DFLEXDPPMS ) & +DP_PHY_MODE_STATUS_COMPLETED (tc_port); +} + +static void icl_tc_phy_set_safe_mode (struct intel_digital_port *dig_port, +bool enable) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +u32 val =I915_READ (PORT_TX_DFLEXDPCSSS ); + + val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); +if (!enable) + val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); + +I915_WRITE (PORT_TX_DFLEXDPCSSS , val); +} +/* * This function implements the first part of the Connect Flow described by our * specification, Gen11 TypeC Programming chapter. The rest of the flow (reading @@ -100,36 +170,31 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port) {struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); -u32 val; +u32 live_status_mask;if (dig_port->tc_mode !=TC_PORT_LEGACY && dig_port->tc_mode !=TC_PORT_DP_ALT )return true; - val =I915_READ (PORT_TX_DFLEXDPPMS ); -if (!(val &DP_PHY_MODE_STATUS_COMPLETED (tc_port))) { +if (!icl_tc_phy_status_complete (dig_port)) {DRM_DEBUG_KMS ("Port %s: PHY not ready\n" ,tc_port_name (dev_priv, tc_port));WARN_ON (dig_port->tc_legacy_port);return false; } -/* -* This function may be called many times in a row without an HPD event -* in between, so try to avoid the write when we can. -*/ - val =I915_READ (PORT_TX_DFLEXDPCSSS ); -if (!(val &DP_PHY_MODE_STATUS_NOT_SAFE (tc_port))) { - val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); -I915_WRITE (PORT_TX_DFLEXDPCSSS , val); - } +icl_tc_phy_set_safe_mode (dig_port, false); + +if (dig_port->tc_mode ==TC_PORT_LEGACY ) +return true; + + live_status_mask =tc_port_live_status_mask (dig_port);/* * Now we have to re-check the live state, in case the port recently * became disconnected. Not necessary for legacy mode. */ -if (dig_port->tc_mode ==TC_PORT_DP_ALT && - !(I915_READ (PORT_TX_DFLEXDPSP ) &TC_LIVE_STATE_TC (tc_port))) { +if (!(live_status_mask &BIT (TC_PORT_DP_ALT ))) {DRM_DEBUG_KMS ("Port %s: PHY sudden disconnect\n" ,tc_port_name (dev_priv, tc_port));icl_tc_phy_disconnect (dig_port);@@ -148,44 +213,36 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port)struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); -/* -* TBT disconnection flow is read the live status, what was done in -* caller. -*/ -if (dig_port->tc_mode ==TC_PORT_DP_ALT || - dig_port->tc_mode ==TC_PORT_LEGACY ) { -u32 val; - - val =I915_READ (PORT_TX_DFLEXDPCSSS ); - val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); -I915_WRITE (PORT_TX_DFLEXDPCSSS , val); +switch (dig_port->tc_mode) { +case TC_PORT_LEGACY : +case TC_PORT_DP_ALT : +icl_tc_phy_set_safe_mode (dig_port, true); + dig_port->tc_mode =TC_PORT_TBT_ALT ; +break ; +case TC_PORT_TBT_ALT : +/* Nothing to do, we stay in TBT-alt mode */ +break ; +default : +MISSING_CASE (dig_port->tc_mode); }DRM_DEBUG_KMS ("Port %s: mode %s disconnected\n" ,tc_port_name (dev_priv, tc_port),tc_port_mode_name (dig_port->tc_mode)); - - dig_port->tc_mode =TC_PORT_TBT_ALT ; }static void icl_update_tc_port_type (struct drm_i915_private *dev_priv,struct intel_digital_port *intel_dig_port, -bool is_legacy,bool is_typec,bool is_tbt) +u32 live_status_mask) {enum port port = intel_dig_port->base.port;enum tc_port_mode old_mode = intel_dig_port->tc_mode; -WARN_ON (is_legacy + is_typec + is_tbt !=1 ); - -if (is_legacy) - intel_dig_port->tc_mode =TC_PORT_LEGACY ; -else if (is_typec) - intel_dig_port->tc_mode =TC_PORT_DP_ALT ; -else if (is_tbt) - intel_dig_port->tc_mode =TC_PORT_TBT_ALT ; -else +if (!live_status_mask)return ; + intel_dig_port->tc_mode =fls (live_status_mask) -1 ; +if (old_mode != intel_dig_port->tc_mode) DRM_DEBUG_KMS("Port %s: port has mode %s\n", tc_port_name(dev_priv,@@ -207,40 +264,19 @@ static void icl_update_tc_port_type(struct drm_i915_private *dev_priv,bool intel_tc_port_connected (struct intel_digital_port *dig_port) {struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); -enum port port = dig_port->base.port; -enum tc_port tc_port =intel_port_to_tc (dev_priv, port); -bool is_legacy, is_typec, is_tbt; -u32 dpsp; - -/* -* Complain if we got a legacy port HPD, but VBT didn't mark the port as -* legacy. Treat the port as legacy from now on. -*/ -if (!dig_port->tc_legacy_port && -I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) { -DRM_ERROR ("Port %s: VBT incorrectly claims port is not TypeC legacy\n" , -tc_port_name (dev_priv, tc_port)); - dig_port->tc_legacy_port = true; - } - is_legacy = dig_port->tc_legacy_port; +u32 live_status_mask =tc_port_live_status_mask (dig_port);/* * The spec says we shouldn't be using the ISR bits for detecting * between TC and TBT. We should use DFLEXDPSP. */ - dpsp =I915_READ (PORT_TX_DFLEXDPSP ); - is_typec = dpsp &TC_LIVE_STATE_TC (tc_port); - is_tbt = dpsp &TC_LIVE_STATE_TBT (tc_port); - -if (!is_legacy && !is_typec && !is_tbt) { +if (!live_status_mask && !dig_port->tc_legacy_port) {icl_tc_phy_disconnect (dig_port);return false; } -icl_update_tc_port_type (dev_priv, dig_port, is_legacy, is_typec, - is_tbt); - +icl_update_tc_port_type (dev_priv, dig_port, live_status_mask);if (!icl_tc_phy_connect (dig_port))return false;drivers/gpu/drm/i915/intel_tc.h +1
-0@@ -8,6 +8,7 @@ struct intel_digital_port;void icl_tc_phy_disconnect (struct intel_digital_port *dig_port);bool intel_tc_port_connected (struct intel_digital_port *dig_port); +u32 intel_tc_port_get_lane_info (struct intel_digital_port *dig_port);int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port);#endif /* __INTEL_TC_H__ */
Signature · 5 lines
Jani Nikula, Intel Open Source Graphics Center _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 09/23] drm/i915: Factor out common parts from TypeC port handling functions
Quoted 53 lines · Jani Nikula
Quoted 52 lines · Imre Deak
Factor out helpers reading/parsing the TypeC specific registers, making current users of them clearer and letting us use them later.
While at it also:
- Simplifyicl_tc_phy_connect()with an early return in legacy mode.
- Simplify the live status check using one bitmask for all HPD bits.
- Remove a micro-optimisation of the repeated safe-mode clearing.
- Make sure we fix the legacy port flag in all cases.Except for the last two, no functional changes.
Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_ddi.c | 5 +- drivers/gpu/drm/i915/intel_tc.c | 166 +++++++++++++++++++------------ drivers/gpu/drm/i915/intel_tc.h | 1 + 3 files changed, 103 insertions(+), 69 deletions(-)drivers/gpu/drm/i915/intel_ddi.c +1
-4@@ -2983,7 +2983,6 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port) {struct drm_i915_private *dev_priv =to_i915 (intel_dig_port->base.base.dev);enum port port = intel_dig_port->base.port; -enum tc_port tc_port =intel_port_to_tc (dev_priv, port);u32 ln0, ln1, lane_info;if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT )@@ -2997,9 +2996,7 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port) ln0 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |MG_DP_MODE_CFG_DP_X2_MODE ); ln1 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |MG_DP_MODE_CFG_DP_X2_MODE ); - lane_info = (I915_READ (PORT_TX_DFLEXDPSP ) & -DP_LANE_ASSIGNMENT_MASK (tc_port)) >> -DP_LANE_ASSIGNMENT_SHIFT (tc_port); + lane_info =intel_tc_port_get_lane_info (intel_dig_port);switch (lane_info) {case 0x1 :drivers/gpu/drm/i915/intel_tc.c +0
-0@@ -43,10 +43,19 @@ static const char *tc_port_mode_name(enum tc_port_mode mode)return names[mode]; }
Quoted 8 lines
drivers/gpu/drm/i915/intel_tc.c static const char *tc_port_mode_name(enum tc_port_mode mode) · line 50
Quoted 6 lines
drivers/gpu/drm/i915/intel_tc.c +2
-1-int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port) +u32 intel_tc_port_get_lane_info (struct intel_digital_port *dig_port) {struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +u32 lane_info =I915_READ (PORT_TX_DFLEXDPSP );Please don't do register reads in declarations. Ditto below.
Ok.
Quoted 250 lines
Quoted 250 lines
drivers/gpu/drm/i915/intel_tc.c +99
-64+ +return (lane_info &DP_LANE_ASSIGNMENT_MASK (tc_port)) >> +DP_LANE_ASSIGNMENT_SHIFT (tc_port); +} + +int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);intel_wakeref_t wakeref;u32 lane_info;@@ -55,9 +64,7 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) lane_info =0 ;with_intel_display_power (dev_priv,POWER_DOMAIN_DISPLAY_CORE , wakeref) - lane_info = (I915_READ(PORT_TX_DFLEXDPSP) & -DP_LANE_ASSIGNMENT_MASK (tc_port)) >> -DP_LANE_ASSIGNMENT_SHIFT (tc_port); + lane_info = intel_tc_port_get_lane_info(dig_port);switch (lane_info) {default :@@ -75,6 +82,69 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) } } +static void tc_port_fixup_legacy_flag (struct intel_digital_port *dig_port, +u32 live_status_mask) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +u32 valid_hpd_mask = dig_port->tc_legacy_port ?BIT (TC_PORT_LEGACY ) : + ~BIT (TC_PORT_LEGACY ); + +if (!(live_status_mask & ~valid_hpd_mask)) +return ; + +/* If live status mismatches the VBT flag, trust the live status. */ +DRM_ERROR ("Port %s: live status %08x mismatches the legacy port flag, fix flag\n" , +tc_port_name (dev_priv, tc_port), live_status_mask); + + dig_port->tc_legacy_port = !dig_port->tc_legacy_port; +} + +static u32 tc_port_live_status_mask (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +u32 val =I915_READ (PORT_TX_DFLEXDPSP ); +u32 mask =0 ; + +if (val &TC_LIVE_STATE_TBT (tc_port)) + mask |=BIT (TC_PORT_TBT_ALT ); +if (val &TC_LIVE_STATE_TC (tc_port)) + mask |=BIT (TC_PORT_DP_ALT ); + +if (I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) + mask |=BIT (TC_PORT_LEGACY ); + +/* The sink can be connected only in a single mode. */ +if (!WARN_ON (hweight32 (mask) >1 )) +tc_port_fixup_legacy_flag (dig_port, mask); + +return mask; +} + +static bool icl_tc_phy_status_complete (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); + +return I915_READ (PORT_TX_DFLEXDPPMS ) & +DP_PHY_MODE_STATUS_COMPLETED (tc_port); +} + +static void icl_tc_phy_set_safe_mode (struct intel_digital_port *dig_port, +bool enable) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +u32 val =I915_READ (PORT_TX_DFLEXDPCSSS ); + + val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); +if (!enable) + val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); + +I915_WRITE (PORT_TX_DFLEXDPCSSS , val); +} +/* * This function implements the first part of the Connect Flow described by our * specification, Gen11 TypeC Programming chapter. The rest of the flow (reading @@ -100,36 +170,31 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port) {struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); -u32 val; +u32 live_status_mask;if (dig_port->tc_mode !=TC_PORT_LEGACY && dig_port->tc_mode !=TC_PORT_DP_ALT )return true; - val =I915_READ (PORT_TX_DFLEXDPPMS ); -if (!(val &DP_PHY_MODE_STATUS_COMPLETED (tc_port))) { +if (!icl_tc_phy_status_complete (dig_port)) {DRM_DEBUG_KMS ("Port %s: PHY not ready\n" ,tc_port_name (dev_priv, tc_port));WARN_ON (dig_port->tc_legacy_port);return false; } -/* -* This function may be called many times in a row without an HPD event -* in between, so try to avoid the write when we can. -*/ - val =I915_READ (PORT_TX_DFLEXDPCSSS ); -if (!(val &DP_PHY_MODE_STATUS_NOT_SAFE (tc_port))) { - val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); -I915_WRITE (PORT_TX_DFLEXDPCSSS , val); - } +icl_tc_phy_set_safe_mode (dig_port, false); + +if (dig_port->tc_mode ==TC_PORT_LEGACY ) +return true; + + live_status_mask =tc_port_live_status_mask (dig_port);/* * Now we have to re-check the live state, in case the port recently * became disconnected. Not necessary for legacy mode. */ -if (dig_port->tc_mode ==TC_PORT_DP_ALT && - !(I915_READ (PORT_TX_DFLEXDPSP ) &TC_LIVE_STATE_TC (tc_port))) { +if (!(live_status_mask &BIT (TC_PORT_DP_ALT ))) {DRM_DEBUG_KMS ("Port %s: PHY sudden disconnect\n" ,tc_port_name (dev_priv, tc_port));icl_tc_phy_disconnect (dig_port);@@ -148,44 +213,36 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port)struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); -/* -* TBT disconnection flow is read the live status, what was done in -* caller. -*/ -if (dig_port->tc_mode ==TC_PORT_DP_ALT || - dig_port->tc_mode ==TC_PORT_LEGACY ) { -u32 val; - - val =I915_READ (PORT_TX_DFLEXDPCSSS ); - val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); -I915_WRITE (PORT_TX_DFLEXDPCSSS , val); +switch (dig_port->tc_mode) { +case TC_PORT_LEGACY : +case TC_PORT_DP_ALT : +icl_tc_phy_set_safe_mode (dig_port, true); + dig_port->tc_mode =TC_PORT_TBT_ALT ; +break ; +case TC_PORT_TBT_ALT : +/* Nothing to do, we stay in TBT-alt mode */ +break ; +default : +MISSING_CASE (dig_port->tc_mode); }DRM_DEBUG_KMS ("Port %s: mode %s disconnected\n" ,tc_port_name (dev_priv, tc_port),tc_port_mode_name (dig_port->tc_mode)); - - dig_port->tc_mode =TC_PORT_TBT_ALT ; }static void icl_update_tc_port_type (struct drm_i915_private *dev_priv,struct intel_digital_port *intel_dig_port, -bool is_legacy,bool is_typec,bool is_tbt) +u32 live_status_mask) {enum port port = intel_dig_port->base.port;enum tc_port_mode old_mode = intel_dig_port->tc_mode; -WARN_ON (is_legacy + is_typec + is_tbt !=1 ); - -if (is_legacy) - intel_dig_port->tc_mode =TC_PORT_LEGACY ; -else if (is_typec) - intel_dig_port->tc_mode =TC_PORT_DP_ALT ; -else if (is_tbt) - intel_dig_port->tc_mode =TC_PORT_TBT_ALT ; -else +if (!live_status_mask)return ; + intel_dig_port->tc_mode =fls (live_status_mask) -1 ; +if (old_mode != intel_dig_port->tc_mode) DRM_DEBUG_KMS("Port %s: port has mode %s\n", tc_port_name(dev_priv,@@ -207,40 +264,19 @@ static void icl_update_tc_port_type(struct drm_i915_private *dev_priv,bool intel_tc_port_connected (struct intel_digital_port *dig_port) {struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); -enum port port = dig_port->base.port; -enum tc_port tc_port =intel_port_to_tc (dev_priv, port); -bool is_legacy, is_typec, is_tbt; -u32 dpsp; - -/* -* Complain if we got a legacy port HPD, but VBT didn't mark the port as -* legacy. Treat the port as legacy from now on. -*/ -if (!dig_port->tc_legacy_port && -I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) { -DRM_ERROR ("Port %s: VBT incorrectly claims port is not TypeC legacy\n" , -tc_port_name (dev_priv, tc_port)); - dig_port->tc_legacy_port = true; - } - is_legacy = dig_port->tc_legacy_port; +u32 live_status_mask =tc_port_live_status_mask (dig_port);/* * The spec says we shouldn't be using the ISR bits for detecting * between TC and TBT. We should use DFLEXDPSP. */ - dpsp =I915_READ (PORT_TX_DFLEXDPSP ); - is_typec = dpsp &TC_LIVE_STATE_TC (tc_port); - is_tbt = dpsp &TC_LIVE_STATE_TBT (tc_port); - -if (!is_legacy && !is_typec && !is_tbt) { +if (!live_status_mask && !dig_port->tc_legacy_port) {icl_tc_phy_disconnect (dig_port);return false; } -icl_update_tc_port_type (dev_priv, dig_port, is_legacy, is_typec, - is_tbt); - +icl_update_tc_port_type (dev_priv, dig_port, live_status_mask);if (!icl_tc_phy_connect (dig_port))return false;drivers/gpu/drm/i915/intel_tc.h +0
-0@@ -8,6 +8,7 @@ struct intel_digital_port;void icl_tc_phy_disconnect (struct intel_digital_port *dig_port);
Quoted 8 lines
Quoted 5 lines
drivers/gpu/drm/i915/intel_tc.h +1
-0bool intel_tc_port_connected (struct intel_digital_port *dig_port); +u32 intel_tc_port_get_lane_info (struct intel_digital_port *dig_port);int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port);#endif /* __INTEL_TC_H__ */ Signature · 1 line
Jani Nikula, Intel Open Source Graphics Center
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 09/23] drm/i915: Factor out common parts from TypeC port handling functions
In reply to Imre DeakQuoted 139 lines · Imre Deak
Factor out helpers reading/parsing the TypeC specific registers, making
current users of them clearer and letting us use them later.While at it also:
- Simplifyicl_tc_phy_connect()with an early return in legacy mode.
- Simplify the live status check using one bitmask for all HPD bits.
- Remove a micro-optimisation of the repeated safe-mode clearing.
- Make sure we fix the legacy port flag in all cases.Except for the last two, no functional changes.
Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_ddi.c | 5 +- drivers/gpu/drm/i915/intel_tc.c | 166 +++++++++++++++++++-------- ---- drivers/gpu/drm/i915/intel_tc.h | 1 + 3 files changed, 103 insertions(+), 69 deletions(-)drivers/gpu/drm/i915/intel_ddi.c +0
-1@@ -2983,7 +2983,6 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port) {struct drm_i915_private *dev_priv =to_i915 (intel_dig_port- >base.base.dev);enum port port = intel_dig_port->base.port; -enum tc_port tc_port =intel_port_to_tc (dev_priv, port);u32 ln0, ln1, lane_info;drivers/gpu/drm/i915/intel_ddi.c +1
-3if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT )@@ -2997,9 +2996,7 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port) ln0 &= ~(MG_DP_MODE_CFG_DP_X1_MODE | MG_DP_MODE_CFG_DP_X2_MODE); ln1 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |MG_DP_MODE_CFG_DP_X2_MODE ); - lane_info = (I915_READ (PORT_TX_DFLEXDPSP ) & -DP_LANE_ASSIGNMENT_MASK (tc_port)) >> -DP_LANE_ASSIGNMENT_SHIFT (tc_port); + lane_info =
intel_tc_port_get_lane_info(intel_dig_port);drivers/gpu/drm/i915/intel_ddi.c +0
-0switch (lane_info) {case 0x1 :drivers/gpu/drm/i915/intel_tc.c +1
-1@@ -43,10 +43,19 @@ static const char *tc_port_mode_name(enum tc_port_mode mode)return names[mode]; } -int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port) +u32 intel_tc_port_get_lane_info (struct intel_digital_port *dig_port) {struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev); enum tc_port tc_port = intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
drivers/gpu/drm/i915/intel_tc.c +7
-0+u32 lane_info =I915_READ (PORT_TX_DFLEXDPSP ); + +return (lane_info &DP_LANE_ASSIGNMENT_MASK (tc_port)) >> +DP_LANE_ASSIGNMENT_SHIFT (tc_port); +} + +int intel_tc_port_fia_max_lane_count(struct intel_digital_port
*dig_port)drivers/gpu/drm/i915/intel_tc.c +2
-0+{ + struct drm_i915_private *dev_priv = to_i915(dig_port-Quoted 1 line
base.base.dev);
drivers/gpu/drm/i915/intel_tc.c +1
-3intel_wakeref_t wakeref;u32 lane_info;@@ -55,9 +64,7 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) lane_info =0 ;with_intel_display_power (dev_priv,POWER_DOMAIN_DISPLAY_CORE , wakeref) - lane_info = (I915_READ(PORT_TX_DFLEXDPSP) & -DP_LANE_ASSIGNMENT_MASK (tc_port)) >> -DP_LANE_ASSIGNMENT_SHIFT (tc_port); + lane_info = intel_tc_port_get_lane_info(dig_port);drivers/gpu/drm/i915/intel_tc.c +5
-0switch (lane_info) {default :@@ -75,6 +82,69 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) } } +static void tc_port_fixup_legacy_flag (struct intel_digital_port *dig_port, +u32 live_status_mask) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev); + enum tc_port tc_port = intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
drivers/gpu/drm/i915/intel_tc.c +1
-0+ u32 valid_hpd_mask = dig_port->tc_legacy_port ?
BIT(TC_PORT_LEGACY):drivers/gpu/drm/i915/intel_tc.c +1
-0+ ~BIT(TC_PORT_LEGACY);
drivers/gpu/drm/i915/intel_tc.c +5
-0+ +if (!(live_status_mask & ~valid_hpd_mask)) +return ; + +/* If live status mismatches the VBT flag, trust the live status. */
drivers/gpu/drm/i915/intel_tc.c +1
-0+ DRM_ERROR("Port %s: live status %08x mismatches the legacy portflag, fix flag\n",
drivers/gpu/drm/i915/intel_tc.c +6
-0+ tc_port_name(dev_priv, tc_port), live_status_mask); + + dig_port->tc_legacy_port = !dig_port->tc_legacy_port; +} + +static u32 tc_port_live_status_mask(struct intel_digital_port
*dig_port)drivers/gpu/drm/i915/intel_tc.c +2
-0+{ + struct drm_i915_private *dev_priv = to_i915(dig_port-Quoted 1 line
base.base.dev);
drivers/gpu/drm/i915/intel_tc.c +1
-0+ enum tc_port tc_port = intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
drivers/gpu/drm/i915/intel_tc.c +4
-0+u32 val =I915_READ (PORT_TX_DFLEXDPSP ); +u32 mask =0 ; + +if (val &TC_LIVE_STATE_TBT (tc_port))
drivers/gpu/drm/i915/intel_tc.c int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) · line 120
Quoted 10 lines
drivers/gpu/drm/i915/intel_tc.c +10
-0+ mask |=BIT (TC_PORT_TBT_ALT ); +if (val &TC_LIVE_STATE_TC (tc_port)) + mask |=BIT (TC_PORT_DP_ALT ); + +if (I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) + mask |=BIT (TC_PORT_LEGACY ); + +/* The sink can be connected only in a single mode. */ +if (!WARN_ON (hweight32 (mask) >1 )) +tc_port_fixup_legacy_flag (dig_port, mask);
The mask should be updated after the fixup
Quoted 24 lines
drivers/gpu/drm/i915/intel_tc.c +5
-0+ +return mask; +} + +static bool icl_tc_phy_status_complete(struct intel_digital_port
*dig_port)drivers/gpu/drm/i915/intel_tc.c +2
-0+{ + struct drm_i915_private *dev_priv = to_i915(dig_port-Quoted 1 line
base.base.dev);
drivers/gpu/drm/i915/intel_tc.c +1
-0+ enum tc_port tc_port = intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
drivers/gpu/drm/i915/intel_tc.c +6
-0+ +return I915_READ (PORT_TX_DFLEXDPPMS ) & +DP_PHY_MODE_STATUS_COMPLETED (tc_port); +} + +static void icl_tc_phy_set_safe_mode(struct intel_digital_port
*dig_port,drivers/gpu/drm/i915/intel_tc.c +3
-0+ bool enable) +{ + struct drm_i915_private *dev_priv = to_i915(dig_port-Quoted 1 line
base.base.dev);
drivers/gpu/drm/i915/intel_tc.c +1
-0+ enum tc_port tc_port = intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
drivers/gpu/drm/i915/intel_tc.c int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) · line 143
Quoted 5 lines
drivers/gpu/drm/i915/intel_tc.c +5
-0+u32 val =I915_READ (PORT_TX_DFLEXDPCSSS ); + + val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); +if (!enable) + val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port);
Why complete remove the optimizations?
You could do:
old_val = val = I915_READ(PORT_TX_DFLEXDPCSSS);
val &= ~DP_PHY_MODE_STATUS_NOT_SAFE(tc_port);
if (!enable)
val |= DP_PHY_MODE_STATUS_NOT_SAFE(tc_port);
if (val != old_val)
I915_WRITE(PORT_TX_DFLEXDPCSSS, val);
Quoted 57 lines
drivers/gpu/drm/i915/intel_tc.c +4
-0+ +I915_WRITE (PORT_TX_DFLEXDPCSSS , val); +} +/* * This function implements the first part of the Connect Flow described by our
* specification, Gen11 TypeC Programming chapter. The rest of the
flow (readingdrivers/gpu/drm/i915/intel_tc.c +2
-5@@ -100,36 +170,31 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port) {struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port- >base.port); -u32 val; +u32 live_status_mask;if (dig_port->tc_mode !=TC_PORT_LEGACY && dig_port->tc_mode !=TC_PORT_DP_ALT )return true; - val =I915_READ (PORT_TX_DFLEXDPPMS ); -if (!(val &DP_PHY_MODE_STATUS_COMPLETED (tc_port))) { +if (!icl_tc_phy_status_complete (dig_port)) {DRM_DEBUG_KMS ("Port %s: PHY not ready\n" ,tc_port_name (dev_priv, tc_port));WARN_ON (dig_port->tc_legacy_port);return false; } -/* -* This function may be called many times in a row without an HPD event
drivers/gpu/drm/i915/intel_tc.c +6
-7-* in between, so try to avoid the write when we can. -*/ - val =I915_READ (PORT_TX_DFLEXDPCSSS ); -if (!(val &DP_PHY_MODE_STATUS_NOT_SAFE (tc_port))) { - val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); -I915_WRITE (PORT_TX_DFLEXDPCSSS , val); - } +icl_tc_phy_set_safe_mode (dig_port, false); + +if (dig_port->tc_mode ==TC_PORT_LEGACY ) +return true; + + live_status_mask =tc_port_live_status_mask (dig_port);/* * Now we have to re-check the live state, in case the port recently
drivers/gpu/drm/i915/intel_tc.c +0
-2* became disconnected. Not necessary for legacy mode. */ - if (dig_port->tc_mode == TC_PORT_DP_ALT && - !(I915_READ(PORT_TX_DFLEXDPSP) &
TC_LIVE_STATE_TC(tc_port))) {
drivers/gpu/drm/i915/intel_tc.c static bool icl_tc_phy_connect(struct intel_digital_port *dig_port) · line 197
Quoted 1 line
drivers/gpu/drm/i915/intel_tc.c +1
-0+if (!(live_status_mask &BIT (TC_PORT_DP_ALT ))) {
When live status is TC_PORT_TBT_ALT it will cause the "sudden disconnect" to be printed each time although icl_tc_phy_disconnect() will do nothing for TBT.
Quoted 99 lines
drivers/gpu/drm/i915/intel_tc.c +0
-2DRM_DEBUG_KMS ("Port %s: PHY sudden disconnect\n" ,tc_port_name (dev_priv, tc_port));icl_tc_phy_disconnect (dig_port);@@ -148,44 +213,36 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port)struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port- >base.port); -/* -* TBT disconnection flow is read the live status, what was done in
drivers/gpu/drm/i915/intel_tc.c +11
-11-* caller. -*/ -if (dig_port->tc_mode ==TC_PORT_DP_ALT || - dig_port->tc_mode ==TC_PORT_LEGACY ) { -u32 val; - - val =I915_READ (PORT_TX_DFLEXDPCSSS ); - val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); -I915_WRITE (PORT_TX_DFLEXDPCSSS , val); +switch (dig_port->tc_mode) { +case TC_PORT_LEGACY : +case TC_PORT_DP_ALT : +icl_tc_phy_set_safe_mode (dig_port, true); + dig_port->tc_mode =TC_PORT_TBT_ALT ; +break ; +case TC_PORT_TBT_ALT : +/* Nothing to do, we stay in TBT-alt mode */ +break ; +default : +MISSING_CASE (dig_port->tc_mode); }DRM_DEBUG_KMS ("Port %s: mode %s disconnected\n" ,tc_port_name (dev_priv, tc_port),tc_port_mode_name (dig_port->tc_mode)); - - dig_port->tc_mode =TC_PORT_TBT_ALT ; } static void icl_update_tc_port_type(struct drm_i915_private
*dev_priv,
structintel_digital_port*intel_dig_port,drivers/gpu/drm/i915/intel_tc.c +0
-1- bool is_legacy, bool is_typec, bool
is_tbt)drivers/gpu/drm/i915/intel_tc.c +4
-16+ u32 live_status_mask) {enum port port = intel_dig_port->base.port;enum tc_port_mode old_mode = intel_dig_port->tc_mode; -WARN_ON (is_legacy + is_typec + is_tbt !=1 ); - -if (is_legacy) - intel_dig_port->tc_mode =TC_PORT_LEGACY ; -else if (is_typec) - intel_dig_port->tc_mode =TC_PORT_DP_ALT ; -else if (is_tbt) - intel_dig_port->tc_mode =TC_PORT_TBT_ALT ; -else +if (!live_status_mask)return ; + intel_dig_port->tc_mode =fls (live_status_mask) -1 ; +if (old_mode != intel_dig_port->tc_mode) DRM_DEBUG_KMS("Port %s: port has mode %s\n", tc_port_name(dev_priv,@@ -207,40 +264,19 @@ static void icl_update_tc_port_type(structdrm_i915_private *dev_priv, bool intel_tc_port_connected(struct intel_digital_port *dig_port) { struct drm_i915_private *dev_priv = to_i915(dig_port- >base.base.dev); -enum port port = dig_port->base.port; -enum tc_port tc_port =intel_port_to_tc (dev_priv, port); -bool is_legacy, is_typec, is_tbt; -u32 dpsp; - -/* -* Complain if we got a legacy port HPD, but VBT didn't mark the port as
drivers/gpu/drm/i915/intel_tc.c +0
-5-* legacy. Treat the port as legacy from now on. -*/ -if (!dig_port->tc_legacy_port && -I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) { - DRM_ERROR("Port %s: VBT incorrectly claims port is notTypeC legacy\n",
drivers/gpu/drm/i915/intel_tc.c +1
-4- tc_port_name(dev_priv, tc_port)); - dig_port->tc_legacy_port = true; - } - is_legacy = dig_port->tc_legacy_port; +u32 live_status_mask =tc_port_live_status_mask (dig_port);/* * The spec says we shouldn't be using the ISR bits for detecting
drivers/gpu/drm/i915/intel_tc.c static void icl_update_tc_port_type(struct drm_i915_private *dev_priv, · line 273
Quoted 8 lines
drivers/gpu/drm/i915/intel_tc.c +1
-5* between TC and TBT. We should use DFLEXDPSP. */ - dpsp =I915_READ (PORT_TX_DFLEXDPSP ); - is_typec = dpsp &TC_LIVE_STATE_TC (tc_port); - is_tbt = dpsp &TC_LIVE_STATE_TBT (tc_port); - -if (!is_legacy && !is_typec && !is_tbt) { +if (!live_status_mask && !dig_port->tc_legacy_port) {
So now it will keep legacy port as unsafe even when disconnected. Maybe worth mention in commit message.
Quoted 27 lines
drivers/gpu/drm/i915/intel_tc.c +0
-1icl_tc_phy_disconnect (dig_port);return false; } - icl_update_tc_port_type(dev_priv, dig_port, is_legacy,
is_typec,drivers/gpu/drm/i915/intel_tc.c +1
-2- is_tbt); - +icl_update_tc_port_type (dev_priv, dig_port, live_status_mask);if (!icl_tc_phy_connect (dig_port))return false;drivers/gpu/drm/i915/intel_tc.h +1
-0@@ -8,6 +8,7 @@ struct intel_digital_port;void icl_tc_phy_disconnect (struct intel_digital_port *dig_port);bool intel_tc_port_connected (struct intel_digital_port *dig_port); +u32 intel_tc_port_get_lane_info (struct intel_digital_port *dig_port);int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port);
Quoted 1 line
#endif /*
__INTEL_TC_H__*/
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 09/23] drm/i915: Factor out common parts from TypeC port handling functions
Quoted 136 lines · Jose
Quoted 135 lines · Imre Deak
Factor out helpers reading/parsing the TypeC specific registers, making
current users of them clearer and letting us use them later.While at it also:
- Simplifyicl_tc_phy_connect()with an early return in legacy mode.
- Simplify the live status check using one bitmask for all HPD bits.
- Remove a micro-optimisation of the repeated safe-mode clearing.
- Make sure we fix the legacy port flag in all cases.Except for the last two, no functional changes.
Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_ddi.c | 5 +- drivers/gpu/drm/i915/intel_tc.c | 166 +++++++++++++++++++-------- ---- drivers/gpu/drm/i915/intel_tc.h | 1 + 3 files changed, 103 insertions(+), 69 deletions(-)drivers/gpu/drm/i915/intel_ddi.c +0
-1@@ -2983,7 +2983,6 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port) {struct drm_i915_private *dev_priv =to_i915 (intel_dig_port- >base.base.dev);enum port port = intel_dig_port->base.port; -enum tc_port tc_port =intel_port_to_tc (dev_priv, port);u32 ln0, ln1, lane_info;drivers/gpu/drm/i915/intel_ddi.c +1
-3if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT )@@ -2997,9 +2996,7 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port) ln0 &= ~(MG_DP_MODE_CFG_DP_X1_MODE | MG_DP_MODE_CFG_DP_X2_MODE); ln1 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |MG_DP_MODE_CFG_DP_X2_MODE ); - lane_info = (I915_READ (PORT_TX_DFLEXDPSP ) & -DP_LANE_ASSIGNMENT_MASK (tc_port)) >> -DP_LANE_ASSIGNMENT_SHIFT (tc_port); + lane_info =
intel_tc_port_get_lane_info(intel_dig_port);drivers/gpu/drm/i915/intel_ddi.c +0
-0switch (lane_info) {case 0x1 :drivers/gpu/drm/i915/intel_tc.c +1
-1@@ -43,10 +43,19 @@ static const char *tc_port_mode_name(enum tc_port_mode mode)return names[mode]; } -int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port) +u32 intel_tc_port_get_lane_info (struct intel_digital_port *dig_port) {struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev); enum tc_port tc_port = intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
drivers/gpu/drm/i915/intel_tc.c +7
-0+u32 lane_info =I915_READ (PORT_TX_DFLEXDPSP ); + +return (lane_info &DP_LANE_ASSIGNMENT_MASK (tc_port)) >> +DP_LANE_ASSIGNMENT_SHIFT (tc_port); +} + +int intel_tc_port_fia_max_lane_count(struct intel_digital_port
*dig_port)drivers/gpu/drm/i915/intel_tc.c +2
-0+{ + struct drm_i915_private *dev_priv = to_i915(dig_port-Quoted 1 line
base.base.dev);
drivers/gpu/drm/i915/intel_tc.c +1
-3intel_wakeref_t wakeref;u32 lane_info;@@ -55,9 +64,7 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) lane_info =0 ;with_intel_display_power (dev_priv,POWER_DOMAIN_DISPLAY_CORE , wakeref) - lane_info = (I915_READ(PORT_TX_DFLEXDPSP) & -DP_LANE_ASSIGNMENT_MASK (tc_port)) >> -DP_LANE_ASSIGNMENT_SHIFT (tc_port); + lane_info = intel_tc_port_get_lane_info(dig_port);drivers/gpu/drm/i915/intel_tc.c +5
-0switch (lane_info) {default :@@ -75,6 +82,69 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) } } +static void tc_port_fixup_legacy_flag (struct intel_digital_port *dig_port, +u32 live_status_mask) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev); + enum tc_port tc_port = intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
drivers/gpu/drm/i915/intel_tc.c +1
-0+ u32 valid_hpd_mask = dig_port->tc_legacy_port ?
BIT(TC_PORT_LEGACY):drivers/gpu/drm/i915/intel_tc.c +1
-0+ ~BIT(TC_PORT_LEGACY);
drivers/gpu/drm/i915/intel_tc.c +5
-0+ +if (!(live_status_mask & ~valid_hpd_mask)) +return ; + +/* If live status mismatches the VBT flag, trust the live status. */
drivers/gpu/drm/i915/intel_tc.c +1
-0+ DRM_ERROR("Port %s: live status %08x mismatches the legacy portflag, fix flag\n",
drivers/gpu/drm/i915/intel_tc.c +6
-0+ tc_port_name(dev_priv, tc_port), live_status_mask); + + dig_port->tc_legacy_port = !dig_port->tc_legacy_port; +} + +static u32 tc_port_live_status_mask(struct intel_digital_port
*dig_port)drivers/gpu/drm/i915/intel_tc.c +2
-0+{ + struct drm_i915_private *dev_priv = to_i915(dig_port-Quoted 1 line
base.base.dev);
drivers/gpu/drm/i915/intel_tc.c +1
-0+ enum tc_port tc_port = intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
Quoted 16 lines
Quoted 4 lines
drivers/gpu/drm/i915/intel_tc.c +4
-0+u32 val =I915_READ (PORT_TX_DFLEXDPSP ); +u32 mask =0 ; + +if (val &TC_LIVE_STATE_TBT (tc_port))drivers/gpu/drm/i915/intel_tc.c int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) · line 120
Quoted 10 lines
drivers/gpu/drm/i915/intel_tc.c +10
-0+ mask |=BIT (TC_PORT_TBT_ALT ); +if (val &TC_LIVE_STATE_TC (tc_port)) + mask |=BIT (TC_PORT_DP_ALT ); + +if (I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) + mask |=BIT (TC_PORT_LEGACY ); + +/* The sink can be connected only in a single mode. */ +if (!WARN_ON (hweight32 (mask) >1 )) +tc_port_fixup_legacy_flag (dig_port, mask);The mask should be updated after the fixup
tc_port_fixup_legacy_flag() will only fix dig_port->tc_legacy_port based on the mask, but mask itself will remain the same. (We trust the live status based mask what is the HW's opinion about what kind of sink got connected.)
If hweight32(mask)>1 we can't really do anything, it'd be some HW issue which we haven't seen so far and that's handled anyway whenever converting the mask to tc_mode by a priority scheme (tc_mode=fls(mask)-1).
Quoted 34 lines
Quoted 25 lines
drivers/gpu/drm/i915/intel_tc.c +5
-0+ +return mask; +} + +static bool icl_tc_phy_status_complete(struct intel_digital_port
*dig_port)drivers/gpu/drm/i915/intel_tc.c +2
-0+{ + struct drm_i915_private *dev_priv = to_i915(dig_port-Quoted 1 line
base.base.dev);
drivers/gpu/drm/i915/intel_tc.c +1
-0+ enum tc_port tc_port = intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
drivers/gpu/drm/i915/intel_tc.c +6
-0+ +return I915_READ (PORT_TX_DFLEXDPPMS ) & +DP_PHY_MODE_STATUS_COMPLETED (tc_port); +} + +static void icl_tc_phy_set_safe_mode(struct intel_digital_port
*dig_port,drivers/gpu/drm/i915/intel_tc.c +3
-0+ bool enable) +{ + struct drm_i915_private *dev_priv = to_i915(dig_port-Quoted 1 line
base.base.dev);
drivers/gpu/drm/i915/intel_tc.c +1
-0+ enum tc_port tc_port = intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
drivers/gpu/drm/i915/intel_tc.c int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) · line 143
Quoted 5 lines
drivers/gpu/drm/i915/intel_tc.c +5
-0+u32 val =I915_READ (PORT_TX_DFLEXDPCSSS ); + + val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); +if (!enable) + val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port);Why complete remove the optimizations?
You could do:
Quoted 8 lines
old_val= val =I915_READ(PORT_TX_DFLEXDPCSSS);
val &= ~DP_PHY_MODE_STATUS_NOT_SAFE(tc_port);if (!enable)
val |= DP_PHY_MODE_STATUS_NOT_SAFE(tc_port);if (val !=
old_val)I915_WRITE(PORT_TX_DFLEXDPCSSS, val);
You could optimize register writes where there is a requirement for it, but there isn't any need for that here.
Quoted 49 lines
Quoted 49 lines
drivers/gpu/drm/i915/intel_tc.c +4
-0+ +I915_WRITE (PORT_TX_DFLEXDPCSSS , val); +} +/* * This function implements the first part of the Connect Flow described by our
* specification, Gen11 TypeC Programming chapter. The rest of the
flow (readingdrivers/gpu/drm/i915/intel_tc.c +2
-5@@ -100,36 +170,31 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port) {struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port- >base.port); -u32 val; +u32 live_status_mask;if (dig_port->tc_mode !=TC_PORT_LEGACY && dig_port->tc_mode !=TC_PORT_DP_ALT )return true; - val =I915_READ (PORT_TX_DFLEXDPPMS ); -if (!(val &DP_PHY_MODE_STATUS_COMPLETED (tc_port))) { +if (!icl_tc_phy_status_complete (dig_port)) {DRM_DEBUG_KMS ("Port %s: PHY not ready\n" ,tc_port_name (dev_priv, tc_port));WARN_ON (dig_port->tc_legacy_port);return false; } -/* -* This function may be called many times in a row without an HPD event
drivers/gpu/drm/i915/intel_tc.c +6
-7-* in between, so try to avoid the write when we can. -*/ - val =I915_READ (PORT_TX_DFLEXDPCSSS ); -if (!(val &DP_PHY_MODE_STATUS_NOT_SAFE (tc_port))) { - val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); -I915_WRITE (PORT_TX_DFLEXDPCSSS , val); - } +icl_tc_phy_set_safe_mode (dig_port, false); + +if (dig_port->tc_mode ==TC_PORT_LEGACY ) +return true; + + live_status_mask =tc_port_live_status_mask (dig_port);
Quoted 12 lines
drivers/gpu/drm/i915/intel_tc.c static bool icl_tc_phy_connect(struct intel_digital_port *dig_port) · line 197
Quoted 9 lines
drivers/gpu/drm/i915/intel_tc.c +0
-0/* * Now we have to re-check the live state, in case the port recently
drivers/gpu/drm/i915/intel_tc.c +0
-2* became disconnected. Not necessary for legacy mode. */ - if (dig_port->tc_mode == TC_PORT_DP_ALT && - !(I915_READ(PORT_TX_DFLEXDPSP) &
TC_LIVE_STATE_TC(tc_port))) {drivers/gpu/drm/i915/intel_tc.c +1
-0+if (!(live_status_mask &BIT (TC_PORT_DP_ALT ))) {When live status is
TC_PORT_TBT_ALTit will cause the "sudden disconnect" to be printed each time
That can't really happen. There was first a DP-alt HPD, after which icl_update_tc_port_type() set tc_mode = TC_PORT_DP_ALT. The only reason for this live status check is to detect a quick unplug of the DP-alt sink (as required by BSpec), after which live status will be 0 here.
Quoted 1 line
although
icl_tc_phy_disconnect()will do nothing for TBT.
We'll have here tc_mode = TC_PORT_DP_ALT, in which case icl_tc_phy_disconnect() will have to switch back to safe mode (since above we switched to unsafe mode already).
Note that there is no change in behaviour here wrt. the current code.
Quoted 97 lines
Quoted 97 lines
drivers/gpu/drm/i915/intel_tc.c +0
-2DRM_DEBUG_KMS ("Port %s: PHY sudden disconnect\n" ,tc_port_name (dev_priv, tc_port));icl_tc_phy_disconnect (dig_port);@@ -148,44 +213,36 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port)struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port- >base.port); -/* -* TBT disconnection flow is read the live status, what was done in
drivers/gpu/drm/i915/intel_tc.c +11
-11-* caller. -*/ -if (dig_port->tc_mode ==TC_PORT_DP_ALT || - dig_port->tc_mode ==TC_PORT_LEGACY ) { -u32 val; - - val =I915_READ (PORT_TX_DFLEXDPCSSS ); - val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port); -I915_WRITE (PORT_TX_DFLEXDPCSSS , val); +switch (dig_port->tc_mode) { +case TC_PORT_LEGACY : +case TC_PORT_DP_ALT : +icl_tc_phy_set_safe_mode (dig_port, true); + dig_port->tc_mode =TC_PORT_TBT_ALT ; +break ; +case TC_PORT_TBT_ALT : +/* Nothing to do, we stay in TBT-alt mode */ +break ; +default : +MISSING_CASE (dig_port->tc_mode); }DRM_DEBUG_KMS ("Port %s: mode %s disconnected\n" ,tc_port_name (dev_priv, tc_port),tc_port_mode_name (dig_port->tc_mode)); - - dig_port->tc_mode =TC_PORT_TBT_ALT ; } static void icl_update_tc_port_type(struct drm_i915_private
*dev_priv,
structintel_digital_port*intel_dig_port,drivers/gpu/drm/i915/intel_tc.c +0
-1- bool is_legacy, bool is_typec, bool
is_tbt)drivers/gpu/drm/i915/intel_tc.c +4
-16+ u32 live_status_mask) {enum port port = intel_dig_port->base.port;enum tc_port_mode old_mode = intel_dig_port->tc_mode; -WARN_ON (is_legacy + is_typec + is_tbt !=1 ); - -if (is_legacy) - intel_dig_port->tc_mode =TC_PORT_LEGACY ; -else if (is_typec) - intel_dig_port->tc_mode =TC_PORT_DP_ALT ; -else if (is_tbt) - intel_dig_port->tc_mode =TC_PORT_TBT_ALT ; -else +if (!live_status_mask)return ; + intel_dig_port->tc_mode =fls (live_status_mask) -1 ; +if (old_mode != intel_dig_port->tc_mode) DRM_DEBUG_KMS("Port %s: port has mode %s\n", tc_port_name(dev_priv,@@ -207,40 +264,19 @@ static void icl_update_tc_port_type(structdrm_i915_private *dev_priv, bool intel_tc_port_connected(struct intel_digital_port *dig_port) { struct drm_i915_private *dev_priv = to_i915(dig_port- >base.base.dev); -enum port port = dig_port->base.port; -enum tc_port tc_port =intel_port_to_tc (dev_priv, port); -bool is_legacy, is_typec, is_tbt; -u32 dpsp; - -/* -* Complain if we got a legacy port HPD, but VBT didn't mark the port as
drivers/gpu/drm/i915/intel_tc.c +0
-5-* legacy. Treat the port as legacy from now on. -*/ -if (!dig_port->tc_legacy_port && -I915_READ (SDEISR ) &SDE_TC_HOTPLUG_ICP (tc_port)) { - DRM_ERROR("Port %s: VBT incorrectly claims port is notTypeC legacy\n",
drivers/gpu/drm/i915/intel_tc.c +1
-4- tc_port_name(dev_priv, tc_port)); - dig_port->tc_legacy_port = true; - } - is_legacy = dig_port->tc_legacy_port; +u32 live_status_mask =tc_port_live_status_mask (dig_port);
Quoted 14 lines
drivers/gpu/drm/i915/intel_tc.c static void icl_update_tc_port_type(struct drm_i915_private *dev_priv, · line 273
Quoted 11 lines
drivers/gpu/drm/i915/intel_tc.c +0
-0/* * The spec says we shouldn't be using the ISR bits for detecting
drivers/gpu/drm/i915/intel_tc.c +1
-5* between TC and TBT. We should use DFLEXDPSP. */ - dpsp =I915_READ (PORT_TX_DFLEXDPSP ); - is_typec = dpsp &TC_LIVE_STATE_TC (tc_port); - is_tbt = dpsp &TC_LIVE_STATE_TBT (tc_port); - -if (!is_legacy && !is_typec && !is_tbt) { +if (!live_status_mask && !dig_port->tc_legacy_port) {So now it will keep legacy port as unsafe even when disconnected. Maybe worth mention in commit message.
That is how it was also before, since above we had
is_legacy = dig_port->tc_legacy_port
So no change in behaviour.
Quoted 22 lines
Quoted 22 lines
drivers/gpu/drm/i915/intel_tc.c +0
-1icl_tc_phy_disconnect (dig_port);return false; } - icl_update_tc_port_type(dev_priv, dig_port, is_legacy,
is_typec,drivers/gpu/drm/i915/intel_tc.c +1
-2- is_tbt); - +icl_update_tc_port_type (dev_priv, dig_port, live_status_mask);if (!icl_tc_phy_connect (dig_port))return false;drivers/gpu/drm/i915/intel_tc.h +0
-0@@ -8,6 +8,7 @@ struct intel_digital_port;void icl_tc_phy_disconnect (struct intel_digital_port *dig_port);
Quoted 7 lines
Quoted 7 lines
drivers/gpu/drm/i915/intel_tc.h +1
-0bool intel_tc_port_connected (struct intel_digital_port *dig_port); +u32 intel_tc_port_get_lane_info (struct intel_digital_port *dig_port);int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port);#endif /*
__INTEL_TC_H__*/
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 09/23] drm/i915: Factor out common parts from TypeC port handling functions
In reply to Imre DeakQuoted 49 lines · Imre Deak
Factor out helpers reading/parsing the TypeC specific registers, making current users of them clearer and letting us use them later.
While at it also:
- Simplifyicl_tc_phy_connect()with an early return in legacy mode.
- Simplify the live status check using one bitmask for all HPD bits.
- Remove a micro-optimisation of the repeated safe-mode clearing.
- Make sure we fix the legacy port flag in all cases.Except for the last two, no functional changes.
Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_ddi.c | 5 +- drivers/gpu/drm/i915/intel_tc.c | 166 +++++++++++++++++++------------ drivers/gpu/drm/i915/intel_tc.h | 1 + 3 files changed, 103 insertions(+), 69 deletions(-)drivers/gpu/drm/i915/intel_ddi.c +1
-4@@ -2983,7 +2983,6 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port) {struct drm_i915_private *dev_priv =to_i915 (intel_dig_port->base.base.dev);enum port port = intel_dig_port->base.port; -enum tc_port tc_port =intel_port_to_tc (dev_priv, port);u32 ln0, ln1, lane_info;if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT )@@ -2997,9 +2996,7 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port) ln0 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |MG_DP_MODE_CFG_DP_X2_MODE ); ln1 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |MG_DP_MODE_CFG_DP_X2_MODE ); - lane_info = (I915_READ (PORT_TX_DFLEXDPSP ) & -DP_LANE_ASSIGNMENT_MASK (tc_port)) >> -DP_LANE_ASSIGNMENT_SHIFT (tc_port); + lane_info =intel_tc_port_get_lane_info (intel_dig_port);switch (lane_info) {case 0x1 :drivers/gpu/drm/i915/intel_tc.c +0
-0
drivers/gpu/drm/i915/intel_tc.c static const char *tc_port_mode_name(enum tc_port_mode mode) · line 46
Quoted 5 lines
drivers/gpu/drm/i915/intel_tc.c +1
-1@@ -43,10 +43,19 @@ static const char *tc_port_mode_name(enum tc_port_mode mode)return names[mode]; } -int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port) +u32 intel_tc_port_get_lane_info (struct intel_digital_port *dig_port)
get_lane_mask() or something?
Quoted 30 lines
drivers/gpu/drm/i915/intel_tc.c +10
-3{struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +u32 lane_info =I915_READ (PORT_TX_DFLEXDPSP ); + +return (lane_info &DP_LANE_ASSIGNMENT_MASK (tc_port)) >> +DP_LANE_ASSIGNMENT_SHIFT (tc_port); +} + +int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);intel_wakeref_t wakeref;u32 lane_info;@@ -55,9 +64,7 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) lane_info =0 ;with_intel_display_power (dev_priv,POWER_DOMAIN_DISPLAY_CORE , wakeref) - lane_info = (I915_READ(PORT_TX_DFLEXDPSP) & -DP_LANE_ASSIGNMENT_MASK (tc_port)) >> -DP_LANE_ASSIGNMENT_SHIFT (tc_port); + lane_info = intel_tc_port_get_lane_info(dig_port);switch (lane_info) {default :@@ -75,6 +82,69 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) } }
drivers/gpu/drm/i915/intel_tc.c int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) · line 94
Quoted 10 lines
drivers/gpu/drm/i915/intel_tc.c +10
-0+static void tc_port_fixup_legacy_flag (struct intel_digital_port *dig_port, +u32 live_status_mask) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +u32 valid_hpd_mask = dig_port->tc_legacy_port ?BIT (TC_PORT_LEGACY ) : + ~BIT (TC_PORT_LEGACY ); + +if (!(live_status_mask & ~valid_hpd_mask)) +return ;
A bit too many nots for me to follow. I guess what it's doing is checking if any of the other bits are set, and if so it assumes the mode was misdeclared in vbt?
Actually, won't this end up ping-ponging back and forth if the hw really reports both legacy and non-legacy bits as set?
Quoted 8 lines
drivers/gpu/drm/i915/intel_tc.c +8
-0+ +/* If live status mismatches the VBT flag, trust the live status. */ +DRM_ERROR ("Port %s: live status %08x mismatches the legacy port flag, fix flag\n" , +tc_port_name (dev_priv, tc_port), live_status_mask); + + dig_port->tc_legacy_port = !dig_port->tc_legacy_port; +} +
Signature · 6 lines
Ville Syrjälä Intel _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 09/23] drm/i915: Factor out common parts from TypeC port handling functions
Quoted 53 lines · Ville Syrjälä
Quoted 52 lines · Imre Deak
Factor out helpers reading/parsing the TypeC specific registers, making current users of them clearer and letting us use them later.
While at it also:
- Simplifyicl_tc_phy_connect()with an early return in legacy mode.
- Simplify the live status check using one bitmask for all HPD bits.
- Remove a micro-optimisation of the repeated safe-mode clearing.
- Make sure we fix the legacy port flag in all cases.Except for the last two, no functional changes.
Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_ddi.c | 5 +- drivers/gpu/drm/i915/intel_tc.c | 166 +++++++++++++++++++------------ drivers/gpu/drm/i915/intel_tc.h | 1 + 3 files changed, 103 insertions(+), 69 deletions(-)drivers/gpu/drm/i915/intel_ddi.c +1
-4@@ -2983,7 +2983,6 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port) {struct drm_i915_private *dev_priv =to_i915 (intel_dig_port->base.base.dev);enum port port = intel_dig_port->base.port; -enum tc_port tc_port =intel_port_to_tc (dev_priv, port);u32 ln0, ln1, lane_info;if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT )@@ -2997,9 +2996,7 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port) ln0 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |MG_DP_MODE_CFG_DP_X2_MODE ); ln1 &= ~(MG_DP_MODE_CFG_DP_X1_MODE |MG_DP_MODE_CFG_DP_X2_MODE ); - lane_info = (I915_READ (PORT_TX_DFLEXDPSP ) & -DP_LANE_ASSIGNMENT_MASK (tc_port)) >> -DP_LANE_ASSIGNMENT_SHIFT (tc_port); + lane_info =intel_tc_port_get_lane_info (intel_dig_port);switch (lane_info) {case 0x1 :drivers/gpu/drm/i915/intel_tc.c +0
-0@@ -43,10 +43,19 @@ static const char *tc_port_mode_name(enum tc_port_mode mode)return names[mode]; }
Quoted 4 lines
drivers/gpu/drm/i915/intel_tc.c static const char *tc_port_mode_name(enum tc_port_mode mode) · line 46
Quoted 2 lines
drivers/gpu/drm/i915/intel_tc.c +1
-1-int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port) +u32 intel_tc_port_get_lane_info (struct intel_digital_port *dig_port)
get_lane_mask()or something?
Ok.
Quoted 31 lines
Quoted 31 lines
drivers/gpu/drm/i915/intel_tc.c +10
-3{struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +u32 lane_info =I915_READ (PORT_TX_DFLEXDPSP ); + +return (lane_info &DP_LANE_ASSIGNMENT_MASK (tc_port)) >> +DP_LANE_ASSIGNMENT_SHIFT (tc_port); +} + +int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);intel_wakeref_t wakeref;u32 lane_info;@@ -55,9 +64,7 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) lane_info =0 ;with_intel_display_power (dev_priv,POWER_DOMAIN_DISPLAY_CORE , wakeref) - lane_info = (I915_READ(PORT_TX_DFLEXDPSP) & -DP_LANE_ASSIGNMENT_MASK (tc_port)) >> -DP_LANE_ASSIGNMENT_SHIFT (tc_port); + lane_info = intel_tc_port_get_lane_info(dig_port);switch (lane_info) {default :@@ -75,6 +82,69 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) } }
Quoted 14 lines
drivers/gpu/drm/i915/intel_tc.c int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) · line 94
Quoted 10 lines
drivers/gpu/drm/i915/intel_tc.c +10
-0+static void tc_port_fixup_legacy_flag (struct intel_digital_port *dig_port, +u32 live_status_mask) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +u32 valid_hpd_mask = dig_port->tc_legacy_port ?BIT (TC_PORT_LEGACY ) : + ~BIT (TC_PORT_LEGACY ); + +if (!(live_status_mask & ~valid_hpd_mask)) +return ;A bit too many nots for me to follow. I guess what it's doing is checking if any of the other bits are set, and if so it assumes the mode was misdeclared in vbt?
Yes.
Quoted 3 lines
Actually, won't this end up ping-ponging back and forth if the hw really reports both legacy and non-legacy bits as set?
If you mean multiple HPD bits being set by HW, we won't call this function to fix up the flag.
Quoted 13 lines
Quoted 9 lines
drivers/gpu/drm/i915/intel_tc.c +8
-0+ +/* If live status mismatches the VBT flag, trust the live status. */ +DRM_ERROR ("Port %s: live status %08x mismatches the legacy port flag, fix flag\n" , +tc_port_name (dev_priv, tc_port), live_status_mask); + + dig_port->tc_legacy_port = !dig_port->tc_legacy_port; +} +Signature · 2 lines
Ville Syrjälä Intel
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 10/23 drm/i915: Wait for TypeC PHY complete flag to clear in safe mode
In reply to Imre DeakThe PHY satus complete flag normally clears when disconnecting the PHY in DP-alt mode (achieved by switching to safe mode), so wait for the flag to clear.
--- drivers/gpu/drm/i915/intel_tc.c | 4 ++++ 1 file changed, 4 insertions(+)
drivers/gpu/drm/i915/intel_tc.c +4 -0
@@ -143,6 +143,10 @@ static void icl_tc_phy_set_safe_mode(struct intel_digital_port *dig_port, val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port);I915_WRITE (PORT_TX_DFLEXDPCSSS , val); + +if (enable &&wait_for (!icl_tc_phy_status_complete (dig_port),10 )) +DRM_DEBUG_DRIVER ("Port %s: PHY complete clear timed out\n" , +tc_port_name (dev_priv, tc_port)); }/*
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 10/23] drm/i915: Wait for TypeC PHY complete flag to clear in safe mode
Quoted 1 line · Imre Deak
The PHY satus complete flag normally clears when disconnecting the
s/satus/status
Quoted 17 lines
PHY
in DP-alt mode (achieved by switching to safe mode), so wait for the flag to clear.Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_tc.c | 4 ++++ 1 file changed, 4 insertions(+)drivers/gpu/drm/i915/intel_tc.c +0
-0
drivers/gpu/drm/i915/intel_tc.c static void icl_tc_phy_set_safe_mode(struct · line 152
Quoted 10 lines
drivers/gpu/drm/i915/intel_tc.c +4
-0@@ -143,6 +143,10 @@ static void icl_tc_phy_set_safe_mode(struct intel_digital_port *dig_port, val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port);I915_WRITE (PORT_TX_DFLEXDPCSSS , val); + +if (enable &&wait_for (!icl_tc_phy_status_complete (dig_port),10 )) +DRM_DEBUG_DRIVER ("Port %s: PHY complete clear timed out\n", +tc_port_name (dev_priv, tc_port));
No mention in spec that we need to do that but it should not harm.
Quoted 3 lines
}
/*
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 11/23 drm/i915: Handle the TCCOLD power-down event
In reply to Imre DeakBased on a recent BSpec update (Index/21750) we must handle the TCCOLD event associated with the DP-alt mode. We can detect this event by reading an invalid all-1s value from FIA registers.
After detecting TCCOLD we will:
- fall back to TBT-alt mode when attempting to switch to DP-alt mode
- conclude that nothing is connected during live status detection
- WARN when already in unsafe mode, since then TCCOLD is unexpected
--- drivers/gpu/drm/i915/intel_tc.c | 23 +++++++++++++++++++++-- 1 file changed, 21 insertions(+), 2 deletions(-)
drivers/gpu/drm/i915/intel_tc.c +21 -2
@@ -49,6 +49,8 @@ u32 intel_tc_port_get_lane_info(struct intel_digital_port *dig_port)enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port);u32 lane_info =I915_READ (PORT_TX_DFLEXDPSP ); +WARN_ON (lane_info ==-1 ); +return (lane_info &DP_LANE_ASSIGNMENT_MASK (tc_port)) >>DP_LANE_ASSIGNMENT_SHIFT (tc_port); }
@@ -107,6 +109,12 @@ static u32 tc_port_live_status_mask(struct intel_digital_port *dig_port)u32 val =I915_READ (PORT_TX_DFLEXDPSP );u32 mask =0 ; +if (val ==-1 ) { +DRM_DEBUG_DRIVER ("Port %s: PHY in TCCOLD, nothing connected\n" , +tc_port_name (dev_priv, tc_port)); +return mask; + } +if (val &TC_LIVE_STATE_TBT (tc_port)) mask |=BIT (TC_PORT_TBT_ALT );if (val &TC_LIVE_STATE_TC (tc_port))
@@ -131,13 +139,21 @@ static bool icl_tc_phy_status_complete(struct intel_digital_port *dig_port)DP_PHY_MODE_STATUS_COMPLETED (tc_port); } -static void icl_tc_phy_set_safe_mode (struct intel_digital_port *dig_port, +static bool icl_tc_phy_set_safe_mode (struct intel_digital_port *dig_port,bool enable) {struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port);u32 val =I915_READ (PORT_TX_DFLEXDPCSSS ); +if (val ==-1 ) { +DRM_DEBUG_DRIVER ("Port %s: PHY in TCCOLD, can't set safe-mode to %s\n" , +tc_port_name (dev_priv, tc_port), +enableddisabled (enable)); + +return false; + } + val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port);if (!enable) val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port);
@@ -147,6 +163,8 @@ static void icl_tc_phy_set_safe_mode(struct intel_digital_port *dig_port,if (enable &&wait_for (!icl_tc_phy_status_complete (dig_port),10 ))DRM_DEBUG_DRIVER ("Port %s: PHY complete clear timed out\n" ,tc_port_name (dev_priv, tc_port)); + +return true; }/*
@@ -187,7 +205,8 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port)return false; } -icl_tc_phy_set_safe_mode (dig_port, false); +if (!icl_tc_phy_set_safe_mode (dig_port, false)) +return false;if (dig_port->tc_mode ==TC_PORT_LEGACY )return true;
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 11/23] drm/i915: Handle the TCCOLD power-down event
Quoted 24 lines · Imre Deak
Based on a recent BSpec update (Index/21750) we must handle the TCCOLD
event associated with the DP-alt mode. We can detect this event by reading an invalid all-1s value from FIA registers.After detecting TCCOLD we will:
- fall back to TBT-alt mode when attempting to switch to DP-alt mode
- conclude that nothing is connected during live status detection
- WARN when already in unsafe mode, since then TCCOLD is unexpectedCc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_tc.c | 23 +++++++++++++++++++++-- 1 file changed, 21 insertions(+), 2 deletions(-)drivers/gpu/drm/i915/intel_tc.c +0
-0
drivers/gpu/drm/i915/intel_tc.c u32 intel_tc_port_get_lane_info(struct · line 54
Quoted 6 lines
drivers/gpu/drm/i915/intel_tc.c +1
-0@@ -49,6 +49,8 @@ u32 intel_tc_port_get_lane_info(struct intel_digital_port *dig_port)enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port- >base.port);u32 lane_info =I915_READ (PORT_TX_DFLEXDPSP ); +WARN_ON (lane_info ==-1 );
I would use 0xFFFFFFFF, it could cause a warning in some compiler(comparing a signed with a unsigned).
Other than that:
Quoted 70 lines
drivers/gpu/drm/i915/intel_tc.c +1
-0+ return (lane_info & DP_LANE_ASSIGNMENT_MASK(tc_port)) >>drivers/gpu/drm/i915/intel_tc.c +6
-0DP_LANE_ASSIGNMENT_SHIFT (tc_port); }@@ -107,6 +109,12 @@ static u32 tc_port_live_status_mask(struct intel_digital_port *dig_port) u32 val = I915_READ(PORT_TX_DFLEXDPSP);u32 mask =0 ; +if (val ==-1 ) { +DRM_DEBUG_DRIVER ("Port %s: PHY in TCCOLD, nothing connected\n", +tc_port_name (dev_priv, tc_port)); +return mask; + } +if (val &TC_LIVE_STATE_TBT (tc_port))drivers/gpu/drm/i915/intel_tc.c +3
-1mask |=BIT (TC_PORT_TBT_ALT );if (val &TC_LIVE_STATE_TC (tc_port))@@ -131,13 +139,21 @@ static bool icl_tc_phy_status_complete(struct intel_digital_port *dig_port)DP_PHY_MODE_STATUS_COMPLETED (tc_port ); } -static void icl_tc_phy_set_safe_mode (struct intel_digital_port *dig_port, +static bool icl_tc_phy_set_safe_mode(struct intel_digital_port *dig_port,bool enable) {struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port- >base.port);u32 val =I915_READ (PORT_TX_DFLEXDPCSSS ); +if (val ==-1 ) { + DRM_DEBUG_DRIVER("Port %s: PHY in TCCOLD, can't setsafe-mode to %s\n",
drivers/gpu/drm/i915/intel_tc.c +8
-0+tc_port_name (dev_priv, tc_port), + enableddisabled(enable)); + +return false; + } + val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port);if (!enable) val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port);@@ -147,6 +163,8 @@ static void icl_tc_phy_set_safe_mode(struct intel_digital_port *dig_port, if (enable && wait_for(!icl_tc_phy_status_complete(dig_port), 10))DRM_DEBUG_DRIVER ("Port %s: PHY complete clear timed out\n",tc_port_name (dev_priv, tc_port)); + +return true;}
/*
drivers/gpu/drm/i915/intel_tc.c +2
-1@@ -187,7 +205,8 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port)return false; } -icl_tc_phy_set_safe_mode (dig_port, false); +if (!icl_tc_phy_set_safe_mode (dig_port, false)) +return false;if (dig_port->tc_mode ==TC_PORT_LEGACY )
Quoted 1 line
return true;
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 11/23] drm/i915: Handle the TCCOLD power-down event
Quoted 27 lines · Jose
Quoted 26 lines · Imre Deak
Based on a recent BSpec update (Index/21750) we must handle the TCCOLD
event associated with the DP-alt mode. We can detect this event by reading an invalid all-1s value from FIA registers.After detecting TCCOLD we will:
- fall back to TBT-alt mode when attempting to switch to DP-alt mode
- conclude that nothing is connected during live status detection
- WARN when already in unsafe mode, since then TCCOLD is unexpectedCc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_tc.c | 23 +++++++++++++++++++++-- 1 file changed, 21 insertions(+), 2 deletions(-)drivers/gpu/drm/i915/intel_tc.c +0
-0@@ -49,6 +49,8 @@ u32 intel_tc_port_get_lane_info(struct intel_digital_port *dig_port) enum tc_port tc_port = intel_port_to_tc(dev_priv, dig_port-
Quoted 7 lines
drivers/gpu/drm/i915/intel_tc.c u32 intel_tc_port_get_lane_info(struct intel_digital_port *dig_port) · line 52
Quoted 4 lines
drivers/gpu/drm/i915/intel_tc.c +1
-0>base.port);u32 lane_info =I915_READ (PORT_TX_DFLEXDPSP ); +WARN_ON (lane_info ==-1 );I would use
0xFFFFFFFF, it could cause a warning in some compiler(comparing a signed with a unsigned).
Shouldn't cause any compiler warnings, since there is a conversion of the types to a common type first, which is unsigned int in this case. That's according to the C standard, so should be fine and it's a short way to write an all-1s value, whatever is on the other side (u32 now, but could be for instance u64).
Quoted 70 lines
Other than that:
Reviewed-by José Roberto de Souza <[email protected]>Quoted 65 lines
drivers/gpu/drm/i915/intel_tc.c +1
-0+ return (lane_info & DP_LANE_ASSIGNMENT_MASK(tc_port)) >>drivers/gpu/drm/i915/intel_tc.c +6
-0DP_LANE_ASSIGNMENT_SHIFT (tc_port); }@@ -107,6 +109,12 @@ static u32 tc_port_live_status_mask(struct intel_digital_port *dig_port) u32 val = I915_READ(PORT_TX_DFLEXDPSP);u32 mask =0 ; +if (val ==-1 ) { +DRM_DEBUG_DRIVER ("Port %s: PHY in TCCOLD, nothing connected\n", +tc_port_name (dev_priv, tc_port)); +return mask; + } +if (val &TC_LIVE_STATE_TBT (tc_port))drivers/gpu/drm/i915/intel_tc.c +3
-1mask |=BIT (TC_PORT_TBT_ALT );if (val &TC_LIVE_STATE_TC (tc_port))@@ -131,13 +139,21 @@ static bool icl_tc_phy_status_complete(struct intel_digital_port *dig_port)DP_PHY_MODE_STATUS_COMPLETED (tc_port ); } -static void icl_tc_phy_set_safe_mode (struct intel_digital_port *dig_port, +static bool icl_tc_phy_set_safe_mode(struct intel_digital_port *dig_port,bool enable) {struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port- >base.port);u32 val =I915_READ (PORT_TX_DFLEXDPCSSS ); +if (val ==-1 ) { + DRM_DEBUG_DRIVER("Port %s: PHY in TCCOLD, can't setsafe-mode to %s\n",
drivers/gpu/drm/i915/intel_tc.c +8
-0+tc_port_name (dev_priv, tc_port), + enableddisabled(enable)); + +return false; + } + val &= ~DP_PHY_MODE_STATUS_NOT_SAFE (tc_port);if (!enable) val |=DP_PHY_MODE_STATUS_NOT_SAFE (tc_port);@@ -147,6 +163,8 @@ static void icl_tc_phy_set_safe_mode(struct intel_digital_port *dig_port, if (enable && wait_for(!icl_tc_phy_status_complete(dig_port), 10))DRM_DEBUG_DRIVER ("Port %s: PHY complete clear timed out\n",tc_port_name (dev_priv, tc_port)); + +return true;}
/*
drivers/gpu/drm/i915/intel_tc.c +0
-0@@ -187,7 +205,8 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port)return false; }
Quoted 6 lines
Quoted 6 lines
drivers/gpu/drm/i915/intel_tc.c +2
-1-icl_tc_phy_set_safe_mode (dig_port, false); +if (!icl_tc_phy_set_safe_mode (dig_port, false)) +return false;if (dig_port->tc_mode ==TC_PORT_LEGACY )return true;
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 12/23 drm/i915: Sanitize the TypeC connect/detect sequences
In reply to Imre DeakMake the order during detection more consistent: first reset the TypeC port mode if needed (adding new helpers for this), then detect any connected sink.
To check if a port mode reset is needed determine first the target port mode based on the live status if a sink is already connected or the PHY status complete flag otherwise.
Add a WARN in legacy mode if unexpectedly we can't set the unsafe mode or if the FIA doesn't provide the 4 lanes required.
--- drivers/gpu/drm/i915/intel_tc.c | 104 +++++++++++++++----------------- 1 file changed, 50 insertions(+), 54 deletions(-)
drivers/gpu/drm/i915/intel_tc.c +50 -54
@@ -188,43 +188,46 @@ static bool icl_tc_phy_set_safe_mode(struct intel_digital_port *dig_port,* will require a lot of coordination with user space and thorough testing for * the extra possible cases. */ -static bool icl_tc_phy_connect (struct intel_digital_port *dig_port) +static void icl_tc_phy_connect (struct intel_digital_port *dig_port) {struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); -u32 live_status_mask; - -if (dig_port->tc_mode !=TC_PORT_LEGACY && - dig_port->tc_mode !=TC_PORT_DP_ALT ) -return true;if (!icl_tc_phy_status_complete (dig_port)) {DRM_DEBUG_KMS ("Port %s: PHY not ready\n" ,tc_port_name (dev_priv, tc_port)); -WARN_ON (dig_port->tc_legacy_port); -return false; + goto out_set_tbt_alt_mode; } -if (!icl_tc_phy_set_safe_mode (dig_port, false)) -return false; +if (!icl_tc_phy_set_safe_mode (dig_port, false) && + !WARN_ON (dig_port->tc_legacy_port)) + goto out_set_tbt_alt_mode; -if (dig_port->tc_mode ==TC_PORT_LEGACY ) -return true; +if (dig_port->tc_legacy_port) { +WARN_ON (intel_tc_port_fia_max_lane_count (dig_port) !=4 ); + dig_port->tc_mode =TC_PORT_LEGACY ; - live_status_mask =tc_port_live_status_mask (dig_port); +return ; + }/* * Now we have to re-check the live state, in case the port recently * became disconnected. Not necessary for legacy mode. */ -if (!(live_status_mask &BIT (TC_PORT_DP_ALT ))) { +if (!(tc_port_live_status_mask (dig_port) &BIT (TC_PORT_DP_ALT ))) {DRM_DEBUG_KMS ("Port %s: PHY sudden disconnect\n" ,tc_port_name (dev_priv, tc_port)); -icl_tc_phy_disconnect (dig_port); -return false; + goto out_set_safe_mode; } -return true; + dig_port->tc_mode =TC_PORT_DP_ALT ; + +return ; + +out_set_safe_mode: +icl_tc_phy_set_safe_mode (dig_port, true); +out_set_tbt_alt_mode: + dig_port->tc_mode =TC_PORT_TBT_ALT ; }/*
@@ -233,9 +236,6 @@ static bool icl_tc_phy_connect(struct intel_digital_port *dig_port)*/ void icl_tc_phy_disconnect (struct intel_digital_port *dig_port) { -struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); -enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); -switch (dig_port->tc_mode) {case TC_PORT_LEGACY :case TC_PORT_DP_ALT :
@@ -248,31 +248,41 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port)default :MISSING_CASE (dig_port->tc_mode); } - -DRM_DEBUG_KMS ("Port %s: mode %s disconnected\n" , -tc_port_name (dev_priv, tc_port), -tc_port_mode_name (dig_port->tc_mode)); } -static void icl_update_tc_port_type (struct drm_i915_private *dev_priv, -struct intel_digital_port *intel_dig_port, -u32 live_status_mask) +static enum tc_port_mode +intel_tc_port_get_target_mode (struct intel_digital_port *dig_port) { -enum port port = intel_dig_port->base.port; -enum tc_port_mode old_mode = intel_dig_port->tc_mode; +u32 live_status_mask =tc_port_live_status_mask (dig_port); -if (!live_status_mask) -return ; +if (live_status_mask) +return fls (live_status_mask) -1 ; + +return icl_tc_phy_status_complete (dig_port) && + dig_port->tc_legacy_port ?TC_PORT_LEGACY : +TC_PORT_TBT_ALT ; +} - intel_dig_port->tc_mode =fls (live_status_mask) -1 ; +static void intel_tc_port_reset_mode (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +enum tc_port_mode old_tc_mode = dig_port->tc_mode; -if (old_mode != intel_dig_port->tc_mode) -DRM_DEBUG_KMS ("Port %s: port has mode %s\n" , -tc_port_name (dev_priv, -intel_port_to_tc (dev_priv, port)), -tc_port_mode_name (intel_dig_port->tc_mode)); +icl_tc_phy_disconnect (dig_port); +icl_tc_phy_connect (dig_port); + +DRM_DEBUG_KMS ("Port %s: TC port mode reset (%s -> %s)\n" , +tc_port_name (dev_priv, tc_port), +tc_port_mode_name (old_tc_mode), +tc_port_mode_name (dig_port->tc_mode)); } +static bool +intel_tc_port_needs_reset (struct intel_digital_port *dig_port) +{ +return intel_tc_port_get_target_mode (dig_port) != dig_port->tc_mode; +}/* * The type-C ports are different because even when they are connected, they may
@@ -286,23 +296,9 @@ static void icl_update_tc_port_type(struct drm_i915_private *dev_priv,*/ bool intel_tc_port_connected (struct intel_digital_port *dig_port) { -struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); -u32 live_status_mask =tc_port_live_status_mask (dig_port); +if (intel_tc_port_needs_reset (dig_port)) +intel_tc_port_reset_mode (dig_port); -/* -* The spec says we shouldn't be using the ISR bits for detecting -* between TC and TBT. We should use DFLEXDPSP. -*/ -if (!live_status_mask && !dig_port->tc_legacy_port) { -icl_tc_phy_disconnect (dig_port); - -return false; - } - -icl_update_tc_port_type (dev_priv, dig_port, live_status_mask); -if (!icl_tc_phy_connect (dig_port)) -return false; - -return true; +return tc_port_live_status_mask (dig_port) &BIT (dig_port->tc_mode); }
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 12/23] drm/i915: Sanitize the TypeC connect/detect sequences
Quoted 134 lines · Imre Deak
Make the order during detection more consistent: first reset the TypeC
port mode if needed (adding new helpers for this), then detect any connected sink.To check if a port mode reset is needed determine first the target port
mode based on the live status if a sink is already connected or the PHY status complete flag otherwise.Add a WARN in legacy mode if unexpectedly we can't set the unsafe mode
or if the FIA doesn't provide the 4 lanes required.Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_tc.c | 104 +++++++++++++++--------------- -- 1 file changed, 50 insertions(+), 54 deletions(-)drivers/gpu/drm/i915/intel_tc.c +0
-0@@ -188,43 +188,46 @@ static bool icl_tc_phy_set_safe_mode(structintel_digital_port *dig_port, * will require a lot of coordination with user space and thoroughtesting for
* the extra possible cases.
*/drivers/gpu/drm/i915/intel_tc.c +1
-1-static bool icl_tc_phy_connect (struct intel_digital_port *dig_port) +static void icl_tc_phy_connect (struct intel_digital_port *dig_port) { struct drm_i915_private *dev_priv = to_i915(dig_port-Quoted 1 line
base.base.dev);
enum
tc_porttc_port= intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
drivers/gpu/drm/i915/intel_tc.c +6
-11-u32 live_status_mask; - -if (dig_port->tc_mode !=TC_PORT_LEGACY && - dig_port->tc_mode !=TC_PORT_DP_ALT ) -return true;if (!icl_tc_phy_status_complete (dig_port)) {DRM_DEBUG_KMS ("Port %s: PHY not ready\n" ,tc_port_name (dev_priv, tc_port)); -WARN_ON (dig_port->tc_legacy_port); -return false; + goto out_set_tbt_alt_mode; } -if (!icl_tc_phy_set_safe_mode (dig_port, false)) -return false; +if (!icl_tc_phy_set_safe_mode (dig_port, false) && + !WARN_ON (dig_port->tc_legacy_port)) + goto out_set_tbt_alt_mode; -if (dig_port->tc_mode ==TC_PORT_LEGACY ) -return true; +if (dig_port->tc_legacy_port) { + WARN_ON(intel_tc_port_fia_max_lane_count(dig_port) !=4);
drivers/gpu/drm/i915/intel_tc.c +3
-1+ dig_port->tc_mode =TC_PORT_LEGACY ; - live_status_mask =tc_port_live_status_mask (dig_port); +return ; + }/* * Now we have to re-check the live state, in case the port recently
drivers/gpu/drm/i915/intel_tc.c +1
-1* became disconnected. Not necessary for legacy mode. */ -if (!(live_status_mask &BIT (TC_PORT_DP_ALT ))) { + if (!(tc_port_live_status_mask(dig_port) &
BIT(TC_PORT_DP_ALT))) {drivers/gpu/drm/i915/intel_tc.c +9
-6DRM_DEBUG_KMS ("Port %s: PHY sudden disconnect\n" ,tc_port_name (dev_priv, tc_port)); -icl_tc_phy_disconnect (dig_port); -return false; + goto out_set_safe_mode; } -return true; + dig_port->tc_mode =TC_PORT_DP_ALT ; + +return ; + +out_set_safe_mode: +icl_tc_phy_set_safe_mode (dig_port, true); +out_set_tbt_alt_mode: + dig_port->tc_mode =TC_PORT_TBT_ALT ; }/* @@ -233,9 +236,6 @@ static bool icl_tc_phy_connect(structintel_digital_port *dig_port) */ void icl_tc_phy_disconnect (struct intel_digital_port *dig_port) { -struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev); -enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port- >base.port); -drivers/gpu/drm/i915/intel_tc.c +2
-9switch (dig_port->tc_mode) {case TC_PORT_LEGACY :case TC_PORT_DP_ALT :@@ -248,31 +248,41 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port)default :MISSING_CASE (dig_port->tc_mode); } - -DRM_DEBUG_KMS ("Port %s: mode %s disconnected\n" , -tc_port_name (dev_priv, tc_port), -tc_port_mode_name (dig_port->tc_mode)); } -static void icl_update_tc_port_type (struct drm_i915_private *dev_priv, -struct intel_digital_port *intel_dig_port, -u32 live_status_mask) +static enum tc_port_mode +intel_tc_port_get_target_mode (struct intel_digital_port *dig_port) { -enum port port = intel_dig_port->base.port; -enum tc_port_mode old_mode = intel_dig_port->tc_mode;
drivers/gpu/drm/i915/intel_tc.c void icl_tc_phy_disconnect(struct · line 266
Quoted 10 lines
drivers/gpu/drm/i915/intel_tc.c +7
-2+u32 live_status_mask =tc_port_live_status_mask (dig_port); -if (!live_status_mask) -return ; +if (live_status_mask) +return fls (live_status_mask) -1 ; + +return icl_tc_phy_status_complete (dig_port) && + dig_port->tc_legacy_port ?TC_PORT_LEGACY : +TC_PORT_TBT_ALT ;
This will return 0 or 1, never TC_PORT_LEGACY(2) because of the "&&".
-TOOMANYREFACTORS
Staring to love again huge patches :P
Quoted 67 lines
drivers/gpu/drm/i915/intel_tc.c +6
-5+} - intel_dig_port->tc_mode =fls (live_status_mask) -1 ; +static void intel_tc_port_reset_mode (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port- >base.port); +enum tc_port_mode old_tc_mode = dig_port->tc_mode; -if (old_mode != intel_dig_port->tc_mode) - DRM_DEBUG_KMS("Port %s: port has mode %s\n", - tc_port_name(dev_priv, - intel_port_to_tc(dev_priv,port)),
drivers/gpu/drm/i915/intel_tc.c +0
-1- tc_port_mode_name(intel_dig_port-Quoted 1 line
tc_mode));drivers/gpu/drm/i915/intel_tc.c +11
-0+icl_tc_phy_disconnect (dig_port); +icl_tc_phy_connect (dig_port); + +DRM_DEBUG_KMS ("Port %s: TC port mode reset (%s -> %s)\n" , +tc_port_name (dev_priv, tc_port), +tc_port_mode_name (old_tc_mode), +tc_port_mode_name (dig_port->tc_mode)); } +static bool +intel_tc_port_needs_reset (struct intel_digital_port *dig_port) +{ + return intel_tc_port_get_target_mode(dig_port) != dig_port-Quoted 1 line
tc_mode;+}
/*
* The type-C ports are different because even when they are
connected, they maydrivers/gpu/drm/i915/intel_tc.c +2
-4@@ -286,23 +296,9 @@ static void icl_update_tc_port_type(structdrm_i915_private *dev_priv, */ bool intel_tc_port_connected (struct intel_digital_port *dig_port) { -struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev); -u32 live_status_mask =tc_port_live_status_mask (dig_port); +if (intel_tc_port_needs_reset (dig_port)) +intel_tc_port_reset_mode (dig_port); -/* -* The spec says we shouldn't be using the ISR bits for detecting
drivers/gpu/drm/i915/intel_tc.c +1
-13-* between TC and TBT. We should use DFLEXDPSP. -*/ -if (!live_status_mask && !dig_port->tc_legacy_port) { -icl_tc_phy_disconnect (dig_port); - -return false; - } - -icl_update_tc_port_type (dev_priv, dig_port, live_status_mask); -if (!icl_tc_phy_connect (dig_port)) -return false; - -return true; + return tc_port_live_status_mask(dig_port) & BIT(dig_port-Quoted 1 line
tc_mode);
Quoted 2 lines
}
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 12/23] drm/i915: Sanitize the TypeC connect/detect sequences
Quoted 137 lines · Jose
Quoted 136 lines · Imre Deak
Make the order during detection more consistent: first reset the TypeC
port mode if needed (adding new helpers for this), then detect any connected sink.To check if a port mode reset is needed determine first the target port
mode based on the live status if a sink is already connected or the PHY status complete flag otherwise.Add a WARN in legacy mode if unexpectedly we can't set the unsafe mode
or if the FIA doesn't provide the 4 lanes required.Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_tc.c | 104 +++++++++++++++--------------- -- 1 file changed, 50 insertions(+), 54 deletions(-)drivers/gpu/drm/i915/intel_tc.c +0
-0@@ -188,43 +188,46 @@ static bool icl_tc_phy_set_safe_mode(structintel_digital_port *dig_port, * will require a lot of coordination with user space and thoroughtesting for
* the extra possible cases.
*/drivers/gpu/drm/i915/intel_tc.c +1
-1-static bool icl_tc_phy_connect (struct intel_digital_port *dig_port) +static void icl_tc_phy_connect (struct intel_digital_port *dig_port) { struct drm_i915_private *dev_priv = to_i915(dig_port-Quoted 1 line
base.base.dev);
enum
tc_porttc_port= intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
drivers/gpu/drm/i915/intel_tc.c +6
-11-u32 live_status_mask; - -if (dig_port->tc_mode !=TC_PORT_LEGACY && - dig_port->tc_mode !=TC_PORT_DP_ALT ) -return true;if (!icl_tc_phy_status_complete (dig_port)) {DRM_DEBUG_KMS ("Port %s: PHY not ready\n" ,tc_port_name (dev_priv, tc_port)); -WARN_ON (dig_port->tc_legacy_port); -return false; + goto out_set_tbt_alt_mode; } -if (!icl_tc_phy_set_safe_mode (dig_port, false)) -return false; +if (!icl_tc_phy_set_safe_mode (dig_port, false) && + !WARN_ON (dig_port->tc_legacy_port)) + goto out_set_tbt_alt_mode; -if (dig_port->tc_mode ==TC_PORT_LEGACY ) -return true; +if (dig_port->tc_legacy_port) { + WARN_ON(intel_tc_port_fia_max_lane_count(dig_port) !=4);
drivers/gpu/drm/i915/intel_tc.c +3
-1+ dig_port->tc_mode =TC_PORT_LEGACY ; - live_status_mask =tc_port_live_status_mask (dig_port); +return ; + }/* * Now we have to re-check the live state, in case the port recently
drivers/gpu/drm/i915/intel_tc.c +1
-1* became disconnected. Not necessary for legacy mode. */ -if (!(live_status_mask &BIT (TC_PORT_DP_ALT ))) { + if (!(tc_port_live_status_mask(dig_port) &
BIT(TC_PORT_DP_ALT))) {drivers/gpu/drm/i915/intel_tc.c +9
-6DRM_DEBUG_KMS ("Port %s: PHY sudden disconnect\n" ,tc_port_name (dev_priv, tc_port)); -icl_tc_phy_disconnect (dig_port); -return false; + goto out_set_safe_mode; } -return true; + dig_port->tc_mode =TC_PORT_DP_ALT ; + +return ; + +out_set_safe_mode: +icl_tc_phy_set_safe_mode (dig_port, true); +out_set_tbt_alt_mode: + dig_port->tc_mode =TC_PORT_TBT_ALT ; }/* @@ -233,9 +236,6 @@ static bool icl_tc_phy_connect(structintel_digital_port *dig_port) */ void icl_tc_phy_disconnect (struct intel_digital_port *dig_port) { -struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev); -enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port- >base.port); -drivers/gpu/drm/i915/intel_tc.c +3
-9switch (dig_port->tc_mode) {case TC_PORT_LEGACY :case TC_PORT_DP_ALT :@@ -248,31 +248,41 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port)default :MISSING_CASE (dig_port->tc_mode); } - -DRM_DEBUG_KMS ("Port %s: mode %s disconnected\n" , -tc_port_name (dev_priv, tc_port), -tc_port_mode_name (dig_port->tc_mode)); } -static void icl_update_tc_port_type (struct drm_i915_private *dev_priv, -struct intel_digital_port *intel_dig_port, -u32 live_status_mask) +static enum tc_port_mode +intel_tc_port_get_target_mode (struct intel_digital_port *dig_port) { -enum port port = intel_dig_port->base.port; -enum tc_port_mode old_mode = intel_dig_port->tc_mode; +u32 live_status_mask =tc_port_live_status_mask (dig_port);
Quoted 10 lines
drivers/gpu/drm/i915/intel_tc.c void icl_tc_phy_disconnect(struct intel_digital_port *dig_port) · line 263
Quoted 8 lines
drivers/gpu/drm/i915/intel_tc.c +6
-2-if (!live_status_mask) -return ; +if (live_status_mask) +return fls (live_status_mask) -1 ; + +return icl_tc_phy_status_complete (dig_port) && + dig_port->tc_legacy_port ?TC_PORT_LEGACY : +TC_PORT_TBT_ALT ;This will return 0 or 1, never
TC_PORT_LEGACY(2)because of the "&&".
Nope, C operators precedence is first "&&" then "?:". Should be fine.
Quoted 2 lines
-TOOMANYREFACTORS
Staring to love again huge patches :P
Well all the previous refactorings should be easier to review, since they don't change the functionality.
The hope was that the refactoring patches make the review of this one
- with functionality changes - easier to review.
Quoted 67 lines
Quoted 67 lines
drivers/gpu/drm/i915/intel_tc.c +6
-5+} - intel_dig_port->tc_mode =fls (live_status_mask) -1 ; +static void intel_tc_port_reset_mode (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev); +enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port- >base.port); +enum tc_port_mode old_tc_mode = dig_port->tc_mode; -if (old_mode != intel_dig_port->tc_mode) - DRM_DEBUG_KMS("Port %s: port has mode %s\n", - tc_port_name(dev_priv, - intel_port_to_tc(dev_priv,port)),
drivers/gpu/drm/i915/intel_tc.c +0
-1- tc_port_mode_name(intel_dig_port-Quoted 1 line
tc_mode));drivers/gpu/drm/i915/intel_tc.c +11
-0+icl_tc_phy_disconnect (dig_port); +icl_tc_phy_connect (dig_port); + +DRM_DEBUG_KMS ("Port %s: TC port mode reset (%s -> %s)\n" , +tc_port_name (dev_priv, tc_port), +tc_port_mode_name (old_tc_mode), +tc_port_mode_name (dig_port->tc_mode)); } +static bool +intel_tc_port_needs_reset (struct intel_digital_port *dig_port) +{ + return intel_tc_port_get_target_mode(dig_port) != dig_port-Quoted 1 line
tc_mode;+}
/*
* The type-C ports are different because even when they are
connected, they maydrivers/gpu/drm/i915/intel_tc.c +2
-4@@ -286,23 +296,9 @@ static void icl_update_tc_port_type(structdrm_i915_private *dev_priv, */ bool intel_tc_port_connected (struct intel_digital_port *dig_port) { -struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev); -u32 live_status_mask =tc_port_live_status_mask (dig_port); +if (intel_tc_port_needs_reset (dig_port)) +intel_tc_port_reset_mode (dig_port); -/* -* The spec says we shouldn't be using the ISR bits for detecting
drivers/gpu/drm/i915/intel_tc.c +1
-13-* between TC and TBT. We should use DFLEXDPSP. -*/ -if (!live_status_mask && !dig_port->tc_legacy_port) { -icl_tc_phy_disconnect (dig_port); - -return false; - } - -icl_update_tc_port_type (dev_priv, dig_port, live_status_mask); -if (!icl_tc_phy_connect (dig_port)) -return false; - -return true; + return tc_port_live_status_mask(dig_port) & BIT(dig_port-
Quoted 3 lines
Quoted 3 lines
Quoted 1 line
tc_mode);}
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 13/23 drm/i915: Fix the TypeC port mode sanitization during loading/resume
In reply to Imre DeakFor using the correct AUX power domains we have to sanitize the TypeC port mode early, so move that before encoder sanitization. To do this properly read out the actual port mode instead of just relying on the VBT legacy port flag (which can be incorrect).
We also verify that the PHY is connected as expected if the port is active. In case the port is inactive we connect the PHY in case of a legacy port - as we did so far. The PHY will be connected during detection for DP-alt mode - as it was done so far. For TBT-alt mode nothing needs to be done to connect the PHY.
--- drivers/gpu/drm/i915/intel_ddi.c | 16 +----- drivers/gpu/drm/i915/intel_display.c | 10 ++++ drivers/gpu/drm/i915/intel_dp_mst.h | 8 ++- drivers/gpu/drm/i915/intel_tc.c | 83 ++++++++++++++++++++++++++++ drivers/gpu/drm/i915/intel_tc.h | 2 + 5 files changed, 103 insertions(+), 16 deletions(-)
drivers/gpu/drm/i915/intel_ddi.c +1 -15
@@ -3918,17 +3918,6 @@ static void intel_ddi_encoder_suspend(struct intel_encoder *encoder)icl_tc_phy_disconnect (dig_port); } -static void intel_ddi_encoder_reset (struct drm_encoder *drm_encoder) -{ -struct intel_digital_port *dig_port =enc_to_dig_port (drm_encoder); -struct drm_i915_private *i915 =to_i915 (drm_encoder->dev); - -if (intel_port_is_tc (i915, dig_port->base.port)) -intel_digital_port_connected (&dig_port->base); - -intel_dp_encoder_reset (drm_encoder); -} -static void intel_ddi_encoder_destroy (struct drm_encoder *encoder) {struct intel_digital_port *dig_port =enc_to_dig_port (encoder);
@@ -3944,7 +3933,7 @@ static void intel_ddi_encoder_destroy(struct drm_encoder *encoder) }static const struct drm_encoder_funcs intel_ddi_funcs = { - .reset = intel_ddi_encoder_reset, + .reset = intel_dp_encoder_reset, .destroy = intel_ddi_encoder_destroy, };
@@ -4309,9 +4298,6 @@ void intel_ddi_init(struct drm_i915_private *dev_priv, enum port port)intel_infoframe_init (intel_dig_port); -if (intel_port_is_tc (dev_priv, port)) -intel_digital_port_connected (intel_encoder); -return ; err:
drivers/gpu/drm/i915/intel_display.c +10 -0
@@ -75,6 +75,7 @@#include "intel_sdvo.h" #include "intel_sideband.h" #include "intel_sprite.h" +#include "intel_tc.h" #include "intel_tv.h" #include "intel_vdsc.h"
@@ -16683,6 +16684,15 @@ intel_modeset_setup_hw_state(struct drm_device *dev,intel_modeset_readout_hw_state (dev);/* HW state is read out, now we need to sanitize this mess. */ + +/* Sanitize the TypeC port mode upfront, encoders depend on this */ +for_each_intel_encoder (dev, encoder) { +/* We need to sanitize only the MST primary port. */ +if (encoder->type !=INTEL_OUTPUT_DP_MST && +intel_port_is_tc (dev_priv, encoder->port)) +intel_tc_port_sanitize (enc_to_dig_port (&encoder->base)); + } +get_encoder_power_domains (dev_priv);if (HAS_PCH_IBX (dev_priv))
drivers/gpu/drm/i915/intel_dp_mst.h +7 -1
@@ -6,9 +6,15 @@#ifndef __INTEL_DP_MST_H__#define __INTEL_DP_MST_H__ -struct intel_digital_port ; +#include "intel_drv.h" int intel_dp_mst_encoder_init (struct intel_digital_port *intel_dig_port,int conn_id);void intel_dp_mst_encoder_cleanup (struct intel_digital_port *intel_dig_port); +static inline int +intel_dp_mst_encoder_active_links (struct intel_digital_port *intel_dig_port) +{ +return intel_dig_port->dp.active_mst_links; +} +#endif /* __INTEL_DP_MST_H__ */
drivers/gpu/drm/i915/intel_tc.c +83 -0
107 lines not on this page · raw message
drivers/gpu/drm/i915/intel_tc.h +2 -0
@@ -11,4 +11,6 @@ bool intel_tc_port_connected(struct intel_digital_port *dig_port);u32 intel_tc_port_get_lane_info (struct intel_digital_port *dig_port);int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port); +void intel_tc_port_sanitize (struct intel_digital_port *dig_port); +#endif /* __INTEL_TC_H__ */
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 13/23] drm/i915: Fix the TypeC port mode sanitization during loading/resume
Quoted 248 lines · Imre Deak
For using the correct AUX power domains we have to sanitize the TypeC port mode early, so move that before encoder sanitization. To do this properly read out the actual port mode instead of just relying on the VBT legacy port flag (which can be incorrect).
We also verify that the PHY is connected as expected if the port is active. In case the port is inactive we connect the PHY in case of a legacy port - as we did so far. The PHY will be connected during detection for DP-alt mode - as it was done so far. For TBT-alt mode nothing needs to be done to connect the PHY.
Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_ddi.c | 16 +----- drivers/gpu/drm/i915/intel_display.c | 10 ++++ drivers/gpu/drm/i915/intel_dp_mst.h | 8 ++- drivers/gpu/drm/i915/intel_tc.c | 83 ++++++++++++++++++++++++++++ drivers/gpu/drm/i915/intel_tc.h | 2 + 5 files changed, 103 insertions(+), 16 deletions(-)drivers/gpu/drm/i915/intel_ddi.c +0
-11@@ -3918,17 +3918,6 @@ static void intel_ddi_encoder_suspend(struct intel_encoder *encoder)icl_tc_phy_disconnect (dig_port ); } -static void intel_ddi_encoder_reset (struct drm_encoder *drm_encoder) -{ -struct intel_digital_port *dig_port =enc_to_dig_port (drm_encoder); -struct drm_i915_private *i915 =to_i915 (drm_encoder->dev); - -if (intel_port_is_tc (i915, dig_port->base.port)) -intel_digital_port_connected (&dig_port->base); - -intel_dp_encoder_reset (drm_encoder); -} -static void intel_ddi_encoder_destroy (struct drm_encoder *encoder){
drivers/gpu/drm/i915/intel_ddi.c +1
-4struct intel_digital_port *dig_port =enc_to_dig_port (encoder);@@ -3944,7 +3933,7 @@ static void intel_ddi_encoder_destroy(struct drm_encoder *encoder) }static const struct drm_encoder_funcs intel_ddi_funcs = { - .reset = intel_ddi_encoder_reset, + .reset = intel_dp_encoder_reset, .destroy = intel_ddi_encoder_destroy, };@@ -4309,9 +4298,6 @@ void intel_ddi_init(struct drm_i915_private *dev_priv, enum port port)intel_infoframe_init (intel_dig_port ); -if (intel_port_is_tc (dev_priv, port)) -intel_digital_port_connected (intel_encoder); -return ;err:
drivers/gpu/drm/i915/intel_display.c +3
-0@@ -75,6 +75,7 @@#include "intel_sdvo.h" #include "intel_sideband.h" #include "intel_sprite.h" +#include "intel_tc.h" #include "intel_tv.h" #include "intel_vdsc.h" @@ -16683,6 +16684,15 @@ intel_modeset_setup_hw_state(structdrm_device *dev,intel_modeset_readout_hw_state (dev );/* HW state is read out, now we need to sanitize this mess. */ + +/* Sanitize the TypeC port mode upfront, encoders depend on this */
drivers/gpu/drm/i915/intel_display.c +7
-1+for_each_intel_encoder (dev, encoder) { +/* We need to sanitize only the MST primary port. */ +if (encoder->type !=INTEL_OUTPUT_DP_MST && +intel_port_is_tc (dev_priv, encoder->port)) + intel_tc_port_sanitize(enc_to_dig_port(&encoder ->base)); + } + get_encoder_power_domains(dev_priv); if (HAS_PCH_IBX(dev_priv))drivers/gpu/drm/i915/intel_dp_mst.h +3
-1@@ -6,9 +6,15 @@#ifndef __INTEL_DP_MST_H__#define __INTEL_DP_MST_H__ -struct intel_digital_port ; +#include "intel_drv.h" int intel_dp_mst_encoder_init (struct intel_digital_port *intel_dig_port,int conn_id);void intel_dp_mst_encoder_cleanup (struct intel_digital_port *intel_dig_port); +static inline int +intel_dp_mst_encoder_active_links(struct intel_digital_port
*intel_dig_port)drivers/gpu/drm/i915/intel_dp_mst.h +4
-0+{ +return intel_dig_port->dp.active_mst_links; +} +#endif /* __INTEL_DP_MST_H__ */ drivers/gpu/drm/i915/intel_tc.c +5
-0@@ -3,6 +3,7 @@* Copyright © 2019 Intel Corporation */ #include "intel_display.h" +#include "intel_dp_mst.h" #include "i915_drv.h" #include "intel_tc.h" @@ -167,6 +168,15 @@ static bool icl_tc_phy_set_safe_mode(structintel_digital_port *dig_port, return true; } +static bool icl_tc_phy_is_in_safe_mode (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev); + enum tc_port tc_port = intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
drivers/gpu/drm/i915/intel_tc.c +5
-0+ +return !(I915_READ (PORT_TX_DFLEXDPCSSS ) & +DP_PHY_MODE_STATUS_NOT_SAFE (tc_port)); +} +/* * This function implements the first part of the Connect Flow described by our
* specification, Gen11 TypeC Programming chapter. The rest of the
flow (readingdrivers/gpu/drm/i915/intel_tc.c +4
-0@@ -250,6 +260,49 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port) } } +static bool icl_tc_phy_is_connected (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev); + enum tc_port tc_port = intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
drivers/gpu/drm/i915/intel_tc.c +26
-0+ +if (!icl_tc_phy_status_complete (dig_port)) { +DRM_DEBUG_KMS ("Port %s: PHY status not complete\n" , +tc_port_name (dev_priv, tc_port)); +return dig_port->tc_mode ==TC_PORT_TBT_ALT ; + } + +if (icl_tc_phy_is_in_safe_mode (dig_port)) { +DRM_DEBUG_KMS ("Port %s: PHY still in safe mode\n" , +tc_port_name (dev_priv, tc_port)); + +return false; + } + +return dig_port->tc_mode ==TC_PORT_DP_ALT || + dig_port->tc_mode ==TC_PORT_LEGACY ; +} + +static enum tc_port_mode +intel_tc_port_get_current_mode (struct intel_digital_port *dig_port) +{ +u32 live_status_mask =tc_port_live_status_mask (dig_port); +bool in_safe_mode =icl_tc_phy_is_in_safe_mode (dig_port); +enum tc_port_mode mode; + + if (in_safe_mode ||WARN_ON(!icl_tc_phy_status_complete(dig_port)))
drivers/gpu/drm/i915/intel_tc.c +3
-0+return TC_PORT_TBT_ALT ; + + mode = dig_port->tc_legacy_port ? TC_PORT_LEGACY :
TC_PORT_DP_ALT;drivers/gpu/drm/i915/intel_tc.c +2
-0+if (live_status_mask) { + enum tc_port_mode live_mode = fls(live_status_mask) -1;
drivers/gpu/drm/i915/intel_tc.c +18
-0+ +if (!WARN_ON (live_mode ==TC_PORT_TBT_ALT )) + mode = live_mode; + } + +return mode; +} +static enum tc_port_mode intel_tc_port_get_target_mode (struct intel_digital_port *dig_port) {@@ -278,6 +331,36 @@ static void intel_tc_port_reset_mode(struct intel_digital_port *dig_port) tc_port_mode_name(dig_port->tc_mode)); } +void intel_tc_port_sanitize (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev); +struct intel_encoder *encoder = &dig_port->base; +enum tc_port tc_port =intel_port_to_tc (dev_priv, encoder- >port); +int active_links =0 ; + + dig_port->tc_mode =intel_tc_port_get_current_mode (dig_port); +if (dig_port->dp.is_mst) + active_links =
intel_dp_mst_encoder_active_links(dig_port);drivers/gpu/drm/i915/intel_tc.c +2
-0+else if (encoder->base.crtc) + active_links = to_intel_crtc(encoder->base.crtc)-Quoted 1 line
active;
drivers/gpu/drm/i915/intel_tc.c +4
-0+ +if (active_links) { +if (!icl_tc_phy_is_connected (dig_port)) + DRM_DEBUG_DRIVER("Port %s: PHY disconnectedwith %d active link(s)\n",
drivers/gpu/drm/i915/intel_tc.c +1
-0+ tc_port_name(dev_priv,
tc_port),
drivers/gpu/drm/i915/intel_tc.c static void intel_tc_port_reset_mode(struct intel_digital_port *dig_port) · line 352
Quoted 2 lines
drivers/gpu/drm/i915/intel_tc.c +2
-0+ active_links); + goto out;
And then probe sequences will take care of callintel_digital_port_connected() to reset TC state.
drivers/gpu/drm/i915/intel_tc.c static void intel_tc_port_reset_mode(struct intel_digital_port *dig_port) · line 361
Quoted 9 lines
drivers/gpu/drm/i915/intel_tc.c +9
-0+ } + +if (dig_port->tc_legacy_port) +icl_tc_phy_connect (dig_port); + +out: +DRM_DEBUG_DRIVER ("Port %s: sanitize mode (%s)\n" , +tc_port_name (dev_priv, tc_port), +tc_port_mode_name (dig_port->tc_mode));
Should be:
DRM_DEBUG_DRIVER()
I guess I missed this on previous patches too.
With that:
Quoted 17 lines
drivers/gpu/drm/i915/intel_tc.c +2
-0+} +static bool intel_tc_port_needs_reset (struct intel_digital_port *dig_port) {drivers/gpu/drm/i915/intel_tc.h +0
-0@@ -11,4 +11,6 @@ bool intel_tc_port_connected(struct intel_digital_port *dig_port);u32 intel_tc_port_get_lane_info (struct intel_digital_port *dig_port); int intel_tc_port_fia_max_lane_count(struct intel_digital_port
*dig_port);
drivers/gpu/drm/i915/intel_tc.h bool intel_tc_port_connected(struct intel_digital_port *dig_port); · line 16
Quoted 3 lines
drivers/gpu/drm/i915/intel_tc.h +2
-0+void intel_tc_port_sanitize (struct intel_digital_port *dig_port); +#endif /* __INTEL_TC_H__ */
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 13/23] drm/i915: Fix the TypeC port mode sanitization during loading/resume
Quoted 242 lines · Jose
Quoted 241 lines · Imre Deak
For using the correct AUX power domains we have to sanitize the TypeC port mode early, so move that before encoder sanitization. To do this properly read out the actual port mode instead of just relying on the VBT legacy port flag (which can be incorrect).
We also verify that the PHY is connected as expected if the port is active. In case the port is inactive we connect the PHY in case of a legacy port - as we did so far. The PHY will be connected during detection for DP-alt mode - as it was done so far. For TBT-alt mode nothing needs to be done to connect the PHY.
Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_ddi.c | 16 +----- drivers/gpu/drm/i915/intel_display.c | 10 ++++ drivers/gpu/drm/i915/intel_dp_mst.h | 8 ++- drivers/gpu/drm/i915/intel_tc.c | 83 ++++++++++++++++++++++++++++ drivers/gpu/drm/i915/intel_tc.h | 2 + 5 files changed, 103 insertions(+), 16 deletions(-)drivers/gpu/drm/i915/intel_ddi.c +0
-11@@ -3918,17 +3918,6 @@ static void intel_ddi_encoder_suspend(struct intel_encoder *encoder)icl_tc_phy_disconnect (dig_port ); } -static void intel_ddi_encoder_reset (struct drm_encoder *drm_encoder) -{ -struct intel_digital_port *dig_port =enc_to_dig_port (drm_encoder); -struct drm_i915_private *i915 =to_i915 (drm_encoder->dev); - -if (intel_port_is_tc (i915, dig_port->base.port)) -intel_digital_port_connected (&dig_port->base); - -intel_dp_encoder_reset (drm_encoder); -} -static void intel_ddi_encoder_destroy (struct drm_encoder *encoder){
drivers/gpu/drm/i915/intel_ddi.c +1
-4struct intel_digital_port *dig_port =enc_to_dig_port (encoder);@@ -3944,7 +3933,7 @@ static void intel_ddi_encoder_destroy(struct drm_encoder *encoder) }static const struct drm_encoder_funcs intel_ddi_funcs = { - .reset = intel_ddi_encoder_reset, + .reset = intel_dp_encoder_reset, .destroy = intel_ddi_encoder_destroy, };@@ -4309,9 +4298,6 @@ void intel_ddi_init(struct drm_i915_private *dev_priv, enum port port)intel_infoframe_init (intel_dig_port ); -if (intel_port_is_tc (dev_priv, port)) -intel_digital_port_connected (intel_encoder); -return ;err:
drivers/gpu/drm/i915/intel_display.c +3
-0@@ -75,6 +75,7 @@#include "intel_sdvo.h" #include "intel_sideband.h" #include "intel_sprite.h" +#include "intel_tc.h" #include "intel_tv.h" #include "intel_vdsc.h" @@ -16683,6 +16684,15 @@ intel_modeset_setup_hw_state(structdrm_device *dev,intel_modeset_readout_hw_state (dev );/* HW state is read out, now we need to sanitize this mess. */ + +/* Sanitize the TypeC port mode upfront, encoders depend on this */
drivers/gpu/drm/i915/intel_display.c +7
-1+for_each_intel_encoder (dev, encoder) { +/* We need to sanitize only the MST primary port. */ +if (encoder->type !=INTEL_OUTPUT_DP_MST && +intel_port_is_tc (dev_priv, encoder->port)) + intel_tc_port_sanitize(enc_to_dig_port(&encoder ->base)); + } + get_encoder_power_domains(dev_priv); if (HAS_PCH_IBX(dev_priv))drivers/gpu/drm/i915/intel_dp_mst.h +3
-1@@ -6,9 +6,15 @@#ifndef __INTEL_DP_MST_H__#define __INTEL_DP_MST_H__ -struct intel_digital_port ; +#include "intel_drv.h" int intel_dp_mst_encoder_init (struct intel_digital_port *intel_dig_port,int conn_id);void intel_dp_mst_encoder_cleanup (struct intel_digital_port *intel_dig_port); +static inline int +intel_dp_mst_encoder_active_links(struct intel_digital_port
*intel_dig_port)drivers/gpu/drm/i915/intel_dp_mst.h +4
-0+{ +return intel_dig_port->dp.active_mst_links; +} +#endif /* __INTEL_DP_MST_H__ */ drivers/gpu/drm/i915/intel_tc.c +5
-0@@ -3,6 +3,7 @@* Copyright © 2019 Intel Corporation */ #include "intel_display.h" +#include "intel_dp_mst.h" #include "i915_drv.h" #include "intel_tc.h" @@ -167,6 +168,15 @@ static bool icl_tc_phy_set_safe_mode(structintel_digital_port *dig_port, return true; } +static bool icl_tc_phy_is_in_safe_mode (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev); + enum tc_port tc_port = intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
drivers/gpu/drm/i915/intel_tc.c +5
-0+ +return !(I915_READ (PORT_TX_DFLEXDPCSSS ) & +DP_PHY_MODE_STATUS_NOT_SAFE (tc_port)); +} +/* * This function implements the first part of the Connect Flow described by our
* specification, Gen11 TypeC Programming chapter. The rest of the
flow (readingdrivers/gpu/drm/i915/intel_tc.c +4
-0@@ -250,6 +260,49 @@ void icl_tc_phy_disconnect(struct intel_digital_port *dig_port) } } +static bool icl_tc_phy_is_connected (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev); + enum tc_port tc_port = intel_port_to_tc(dev_priv, dig_port-Quoted 1 line
base.port);
drivers/gpu/drm/i915/intel_tc.c +26
-0+ +if (!icl_tc_phy_status_complete (dig_port)) { +DRM_DEBUG_KMS ("Port %s: PHY status not complete\n" , +tc_port_name (dev_priv, tc_port)); +return dig_port->tc_mode ==TC_PORT_TBT_ALT ; + } + +if (icl_tc_phy_is_in_safe_mode (dig_port)) { +DRM_DEBUG_KMS ("Port %s: PHY still in safe mode\n" , +tc_port_name (dev_priv, tc_port)); + +return false; + } + +return dig_port->tc_mode ==TC_PORT_DP_ALT || + dig_port->tc_mode ==TC_PORT_LEGACY ; +} + +static enum tc_port_mode +intel_tc_port_get_current_mode (struct intel_digital_port *dig_port) +{ +u32 live_status_mask =tc_port_live_status_mask (dig_port); +bool in_safe_mode =icl_tc_phy_is_in_safe_mode (dig_port); +enum tc_port_mode mode; + + if (in_safe_mode ||WARN_ON(!icl_tc_phy_status_complete(dig_port)))
drivers/gpu/drm/i915/intel_tc.c +3
-0+return TC_PORT_TBT_ALT ; + + mode = dig_port->tc_legacy_port ? TC_PORT_LEGACY :
TC_PORT_DP_ALT;drivers/gpu/drm/i915/intel_tc.c +2
-0+if (live_status_mask) { + enum tc_port_mode live_mode = fls(live_status_mask) -1;
drivers/gpu/drm/i915/intel_tc.c +18
-0+ +if (!WARN_ON (live_mode ==TC_PORT_TBT_ALT )) + mode = live_mode; + } + +return mode; +} +static enum tc_port_mode intel_tc_port_get_target_mode (struct intel_digital_port *dig_port) {@@ -278,6 +331,36 @@ static void intel_tc_port_reset_mode(struct intel_digital_port *dig_port) tc_port_mode_name(dig_port->tc_mode)); } +void intel_tc_port_sanitize (struct intel_digital_port *dig_port) +{ +struct drm_i915_private *dev_priv =to_i915 (dig_port- >base.base.dev); +struct intel_encoder *encoder = &dig_port->base; +enum tc_port tc_port =intel_port_to_tc (dev_priv, encoder- >port); +int active_links =0 ; + + dig_port->tc_mode =intel_tc_port_get_current_mode (dig_port); +if (dig_port->dp.is_mst) + active_links =
intel_dp_mst_encoder_active_links(dig_port);drivers/gpu/drm/i915/intel_tc.c +2
-0+else if (encoder->base.crtc) + active_links = to_intel_crtc(encoder->base.crtc)-Quoted 1 line
active;
Quoted 12 lines
drivers/gpu/drm/i915/intel_tc.c static void intel_tc_port_reset_mode(struct intel_digital_port *dig_port) · line 352
Quoted 9 lines
drivers/gpu/drm/i915/intel_tc.c +4
-0+ +if (active_links) { +if (!icl_tc_phy_is_connected (dig_port)) + DRM_DEBUG_DRIVER("Port %s: PHY disconnectedwith %d active link(s)\n",
drivers/gpu/drm/i915/intel_tc.c +1
-0+ tc_port_name(dev_priv,
tc_port),drivers/gpu/drm/i915/intel_tc.c +2
-0+ active_links); + goto out;And then probe sequences will take care of call
intel_digital_port_connected()to reset TC state.
Right, once the active mode (we detected here) gets disabled, since before that you can't reset the mode. Btw, we'll also check if a mode reset is needed before AUX transfers (if the port is not active).
Quoted 13 lines
drivers/gpu/drm/i915/intel_tc.c static void intel_tc_port_reset_mode(struct intel_digital_port *dig_port) · line 361
Quoted 10 lines
drivers/gpu/drm/i915/intel_tc.c +9
-0+ } + +if (dig_port->tc_legacy_port) +icl_tc_phy_connect (dig_port); + +out: +DRM_DEBUG_DRIVER ("Port %s: sanitize mode (%s)\n" , +tc_port_name (dev_priv, tc_port), +tc_port_mode_name (dig_port->tc_mode));Should be:
Quoted 3 lines
DRM_DEBUG_DRIVER()I guess I missed this on previous patches too.
Ah right, DRM_DEBUG_KMS().
Quoted 23 lines
With that:
Reviewed-by José Roberto de Souza <[email protected]>Quoted 17 lines
drivers/gpu/drm/i915/intel_tc.c +2
-0+} +static bool intel_tc_port_needs_reset (struct intel_digital_port *dig_port) {drivers/gpu/drm/i915/intel_tc.h +0
-0@@ -11,4 +11,6 @@ bool intel_tc_port_connected(struct intel_digital_port *dig_port);u32 intel_tc_port_get_lane_info (struct intel_digital_port *dig_port); int intel_tc_port_fia_max_lane_count(struct intel_digital_port
*dig_port);
Quoted 3 lines
drivers/gpu/drm/i915/intel_tc.h bool intel_tc_port_connected(struct intel_digital_port *dig_port); · line 16
Quoted 3 lines
drivers/gpu/drm/i915/intel_tc.h +2
-0+void intel_tc_port_sanitize (struct intel_digital_port *dig_port); +#endif /* __INTEL_TC_H__ */
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 14/23 drm/i915: Keep the TypeC port mode fixed for detect/AUX transfers
In reply to Imre DeakWe must keep the TypeC port mode fixed for the duration of the connector detection and each AUX transfers. Add a new TypeC lock holding it around these two sequences. For consistency also hold the lock during the port mode sanitization.
Whenever resetting the port mode (only during the detection for now) the port's AUX power domain must be disabled already. Flush the async power domain disabling work to ensure this.
A follow-up patch will make the port mode changing more robust by postponing the change for active ports.
--- drivers/gpu/drm/i915/intel_ddi.c | 9 ++++++--- drivers/gpu/drm/i915/intel_dp.c | 7 +++++++ drivers/gpu/drm/i915/intel_drv.h | 1 + drivers/gpu/drm/i915/intel_tc.c | 34 +++++++++++++++++++++++++++++++- drivers/gpu/drm/i915/intel_tc.h | 4 ++++ 5 files changed, 51 insertions(+), 4 deletions(-)
drivers/gpu/drm/i915/intel_ddi.c +6 -3
@@ -4235,9 +4235,12 @@ void intel_ddi_init(struct drm_i915_private *dev_priv, enum port port) intel_dig_port->max_lanes =intel_ddi_max_lanes (intel_dig_port); intel_dig_port->aux_ch =intel_bios_port_aux_ch (dev_priv, port); - intel_dig_port->tc_legacy_port =intel_port_is_tc (dev_priv, port) && - !port_info->supports_typec_usb && - !port_info->supports_tbt; +if (intel_port_is_tc (dev_priv, port)) { +bool is_legacy = !port_info->supports_typec_usb && + !port_info->supports_tbt; + +intel_tc_port_init (intel_dig_port, is_legacy); + }switch (port) {case PORT_A :
drivers/gpu/drm/i915/intel_dp.c +7 -0
@@ -1190,6 +1190,7 @@ intel_dp_aux_xfer(struct intel_dp *intel_dp,struct intel_digital_port *intel_dig_port =dp_to_dig_port (intel_dp);struct drm_i915_private *dev_priv =to_i915 (intel_dig_port->base.base.dev); +bool is_tc_port =intel_port_is_tc (dev_priv, intel_dig_port->base.port);i915_reg_t ch_ctl, ch_data[5 ];u32 aux_clock_divider; enum intel_display_power_domain aux_domain =
@@ -1205,6 +1206,9 @@ intel_dp_aux_xfer(struct intel_dp *intel_dp,for (i =0 ; i <ARRAY_SIZE (ch_data); i++) ch_data[i] = intel_dp->aux_ch_data_reg (intel_dp, i); +if (is_tc_port) +intel_tc_port_lock (intel_dig_port); + aux_wakeref =intel_display_power_get (dev_priv, aux_domain); pps_wakeref =pps_lock (intel_dp);
@@ -1355,6 +1359,9 @@ intel_dp_aux_xfer(struct intel_dp *intel_dp,pps_unlock (intel_dp, pps_wakeref);intel_display_power_put_async (dev_priv, aux_domain, aux_wakeref); +if (is_tc_port) +intel_tc_port_unlock (intel_dig_port); +return ret; }
drivers/gpu/drm/i915/intel_drv.h +1 -0
@@ -1224,6 +1224,7 @@ struct intel_digital_port {/* Used for DP and ICL+ TypeC/DP and TypeC/HDMI ports. */ enum aux_ch aux_ch;enum intel_display_power_domain ddi_io_power_domain; +struct mutex tc_lock; bool tc_legacy_port:1;enum tc_port_mode tc_mode;
drivers/gpu/drm/i915/intel_tc.c +33 -1
@@ -322,6 +322,8 @@ static void intel_tc_port_reset_mode(struct intel_digital_port *dig_port)enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port);enum tc_port_mode old_tc_mode = dig_port->tc_mode; +intel_display_power_flush_work (dev_priv); +icl_tc_phy_disconnect (dig_port);icl_tc_phy_connect (dig_port);
@@ -338,6 +340,8 @@ void intel_tc_port_sanitize(struct intel_digital_port *dig_port)enum tc_port tc_port =intel_port_to_tc (dev_priv, encoder->port);int active_links =0 ; +mutex_lock (&dig_port->tc_lock); + dig_port->tc_mode =intel_tc_port_get_current_mode (dig_port);if (dig_port->dp.is_mst) active_links =intel_dp_mst_encoder_active_links (dig_port);
@@ -359,6 +363,8 @@ void intel_tc_port_sanitize(struct intel_digital_port *dig_port)DRM_DEBUG_DRIVER ("Port %s: sanitize mode (%s)\n" ,tc_port_name (dev_priv, tc_port),tc_port_mode_name (dig_port->tc_mode)); + +mutex_unlock (&dig_port->tc_lock); } static bool
@@ -379,9 +385,35 @@ intel_tc_port_needs_reset(struct intel_digital_port *dig_port)*/ bool intel_tc_port_connected (struct intel_digital_port *dig_port) { +bool is_connected; + +mutex_lock (&dig_port->tc_lock); +if (intel_tc_port_needs_reset (dig_port))intel_tc_port_reset_mode (dig_port); -return tc_port_live_status_mask (dig_port) &BIT (dig_port->tc_mode); + is_connected =tc_port_live_status_mask (dig_port) & +BIT (dig_port->tc_mode); + +mutex_unlock (&dig_port->tc_lock); + +return is_connected; } +void intel_tc_port_lock (struct intel_digital_port *dig_port) +{ +mutex_lock (&dig_port->tc_lock); +/* TODO: reset the TypeC port mode if needed */ +} + +void intel_tc_port_unlock (struct intel_digital_port *dig_port) +{ +mutex_unlock (&dig_port->tc_lock); +} + +void +intel_tc_port_init (struct intel_digital_port *dig_port,bool is_legacy) +{ +mutex_init (&dig_port->tc_lock); + dig_port->tc_legacy_port = is_legacy; +}
drivers/gpu/drm/i915/intel_tc.h +4 -0
@@ -12,5 +12,9 @@ u32 intel_tc_port_get_lane_info(struct intel_digital_port *dig_port);int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port);void intel_tc_port_sanitize (struct intel_digital_port *dig_port); +void intel_tc_port_lock (struct intel_digital_port *dig_port); +void intel_tc_port_unlock (struct intel_digital_port *dig_port); + +void intel_tc_port_init (struct intel_digital_port *dig_port,bool is_legacy);#endif /* __INTEL_TC_H__ */
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 15/23 drm/i915: Sanitize the TypeC FIA lane configuration decoding
In reply to Imre DeakUse hex numbers, since that makes more sense when decoding a bit pattern.
No functional change.
--- drivers/gpu/drm/i915/intel_tc.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-)
drivers/gpu/drm/i915/intel_tc.c +8 -7
@@ -72,15 +72,16 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port)switch (lane_info) {default :MISSING_CASE (lane_info); -case 1 : -case 2 : -case 4 : -case 8 : +/* fall-through */ +case 0x1 : +case 0x2 : +case 0x4 : +case 0x8 :return 1 ; -case 3 : -case 12 : +case 0x3 : +case 0xc :return 2 ; -case 15 : +case 0xf :return 4 ; } }
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 15/23] drm/i915: Sanitize the TypeC FIA lane configuration decoding
Quoted 4 lines · Imre Deak
Use hex numbers, since that makes more sense when decoding a bit pattern.
No functional change.
Quoted 38 lines
Suggested-by Ville Syrjälä <[email protected]>Cc Animesh Manna <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_tc.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-)drivers/gpu/drm/i915/intel_tc.c +8
-7@@ -72,15 +72,16 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) switch (lane_info) {default :MISSING_CASE (lane_info); -case 1 : -case 2 : -case 4 : -case 8 : +/* fall-through */ +case 0x1 : +case 0x2 : +case 0x4 : +case 0x8 :return 1 ; -case 3 : -case 12 : +case 0x3 : +case 0xc :return 2 ; -case 15 : +case 0xf :return 4 ; }
Quoted 1 line
}
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 15/23] drm/i915: Sanitize the TypeC FIA lane configuration decoding
In reply to Imre DeakQuoted 29 lines · Imre Deak
Use hex numbers, since that makes more sense when decoding a bit pattern.
No functional change.
Suggested-by Ville Syrjälä <[email protected]>Cc Animesh Manna <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_tc.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-)drivers/gpu/drm/i915/intel_tc.c +5
-4@@ -72,15 +72,16 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port)switch (lane_info) {default :MISSING_CASE (lane_info); -case 1 : -case 2 : -case 4 : -case 8 : +/* fall-through */ +case 0x1 : +case 0x2 : +case 0x4 : +case 0x8 :
drivers/gpu/drm/i915/intel_tc.c int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) · line 86
Quoted 10 lines
drivers/gpu/drm/i915/intel_tc.c +3
-3return 1 ; -case 3 : -case 12 : +case 0x3 : +case 0xc :return 2 ; -case 15 : +case 0xf :return 4 ; }
Still looks like a hand rolled hweight() to me ;)
Quoted 3 lines
drivers/gpu/drm/i915/intel_tc.c +0
-0}Signature · 1 line
2.17.1
Signature · 6 lines
Ville Syrjälä Intel _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 15/23] drm/i915: Sanitize the TypeC FIA lane configuration decoding
Quoted 34 lines · Ville Syrjälä
Quoted 33 lines · Imre Deak
Use hex numbers, since that makes more sense when decoding a bit pattern.
No functional change.
Suggested-by Ville Syrjälä <[email protected]>Cc Animesh Manna <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_tc.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-)drivers/gpu/drm/i915/intel_tc.c +6
-6@@ -72,15 +72,16 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port)switch (lane_info) {default :MISSING_CASE (lane_info); -case 1 : -case 2 : -case 4 : -case 8 : +/* fall-through */ +case 0x1 : +case 0x2 : +case 0x4 : +case 0x8 :return 1 ; -case 3 : -case 12 : +case 0x3 :
Quoted 8 lines
drivers/gpu/drm/i915/intel_tc.c int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port) · line 86
Quoted 6 lines
drivers/gpu/drm/i915/intel_tc.c +2
-1+case 0xc :return 2 ; -case 15 : +case 0xf :return 4 ; }Still looks like a hand rolled
hweight()to me ;)
Thought about that, but then we'd miss undefined encodings.
Quoted 8 lines
Quoted 4 lines
drivers/gpu/drm/i915/intel_tc.c +0
-0}Signature · 1 line
2.17.1Signature · 2 lines
Ville Syrjälä Intel
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 16/23 drm/i915: Sanitize the shared DPLL reserve/release interface
In reply to Imre DeakFor consistency s/intel_get_shared_dpll()/intel_reserve_shared_dplls()/ to better match intel_release_shared_dplls(). Also, pass to the reserve/release and get_dplls/put_dplls hooks the intel_atomic_state and CRTC object, that way these functions can look up the old or new state as needed.
Also release the PLLs from the atomic state via a new put_dplls->intel_unreference_shared_dpll() call chain for better symmetry with the reservation via the get_dplls->intel_reference_shared_dpll() call chain.
Since nothing uses the PLL returned by intel_reserve_shared_dplls(), make it return only a bool.
While at it also clarify the reserve/release function docbook headers making it clear that multiple DPLLs will be reserved/released and whether the new or old atomic CRTC state is affected.
This refactoring is also a preparation for a follow-up change that needs to reserve multiple DPLLs.
Kudos to Ville for the idea to pass intel_atomic_state around, to make things clearer locally where an object's old/new atomic state is required.
No functional changes.
--- drivers/gpu/drm/i915/intel_display.c | 19 +-- drivers/gpu/drm/i915/intel_dpll_mgr.c | 221 ++++++++++++++++---------- drivers/gpu/drm/i915/intel_dpll_mgr.h | 13 +- 3 files changed, 153 insertions(+), 100 deletions(-)
drivers/gpu/drm/i915/intel_display.c +7 -12
@@ -9425,6 +9425,8 @@ static int ironlake_crtc_compute_clock(struct intel_crtc *crtc, struct intel_crtc_state *crtc_state) {struct drm_i915_private *dev_priv =to_i915 (crtc->base.dev); +struct intel_atomic_state *state = +to_intel_atomic_state (crtc_state->base.state);const struct intel_limit *limit;int refclk =120000 ;
@@ -9466,7 +9468,7 @@ static int ironlake_crtc_compute_clock(struct intel_crtc *crtc,ironlake_compute_dpll (crtc, crtc_state,NULL ); -if (!intel_get_shared_dpll (crtc_state,NULL )) { +if (!intel_reserve_shared_dplls (state, crtc,NULL )) {DRM_DEBUG_KMS ("failed to find PLL for pipe %c\n" ,pipe_name (crtc->pipe));return -EINVAL ;
@@ -9846,7 +9848,7 @@ static int haswell_crtc_compute_clock(struct intel_crtc *crtc,struct intel_encoder *encoder =intel_get_crtc_new_encoder (state, crtc_state); -if (!intel_get_shared_dpll (crtc_state, encoder)) { +if (!intel_reserve_shared_dplls (state, crtc, encoder)) {DRM_DEBUG_KMS ("failed to find PLL for pipe %c\n" ,pipe_name (crtc->pipe));return -EINVAL ;
@@ -13121,27 +13123,20 @@ static void update_scanline_offset(const struct intel_crtc_state *crtc_state)static void intel_modeset_clear_plls (struct intel_atomic_state *state) {struct drm_i915_private *dev_priv =to_i915 (state->base.dev); -struct intel_crtc_state *old_crtc_state, *new_crtc_state; +struct intel_crtc_state *new_crtc_state;struct intel_crtc *crtc;int i;if (!dev_priv->display.crtc_compute_clock)return ; -for_each_oldnew_intel_crtc_in_state (state, crtc, old_crtc_state, - new_crtc_state, i) { -struct intel_shared_dpll *old_dpll = - old_crtc_state->shared_dpll; - +for_each_new_intel_crtc_in_state (state, crtc, new_crtc_state, i) {if (!needs_modeset (&new_crtc_state->base))continue ; new_crtc_state->shared_dpll =NULL ; -if (!old_dpll) -continue ; - -intel_release_shared_dpll (old_dpll, crtc, &state->base); +intel_release_shared_dplls (state, crtc); } }
drivers/gpu/drm/i915/intel_dpll_mgr.c +139 -82
457 lines not on this page · raw message
drivers/gpu/drm/i915/intel_dpll_mgr.h +7 -6
@@ -39,6 +39,7 @@struct drm_atomic_state ;struct drm_device ;struct drm_i915_private ; +struct intel_atomic_state ;struct intel_crtc ;struct intel_crtc_state ;struct intel_encoder ;
@@ -195,7 +196,7 @@ struct intel_dpll_hw_state {* future state which would be applied by an atomic mode set (stored in * a struct &intel_atomic_state). * -* See also intel_get_shared_dpll() and intel_release_shared_dpll(). +* See also intel_reserve_shared_dplls() and intel_release_shared_dplls(). */ struct intel_shared_dpll_state {/**
@@ -331,11 +332,11 @@ void assert_shared_dpll(struct drm_i915_private *dev_priv, bool state);#define assert_shared_dpll_enabled (d, p) assert_shared_dpll(d, p, true)#define assert_shared_dpll_disabled (d, p) assert_shared_dpll(d, p, false) -struct intel_shared_dpll *intel_get_shared_dpll (struct intel_crtc_state *state, -struct intel_encoder *encoder); -void intel_release_shared_dpll (struct intel_shared_dpll *dpll, -struct intel_crtc *crtc, -struct drm_atomic_state *state); +bool intel_reserve_shared_dplls (struct intel_atomic_state *state, +struct intel_crtc *crtc, +struct intel_encoder *encoder); +void intel_release_shared_dplls (struct intel_atomic_state *state, +struct intel_crtc *crtc);void intel_prepare_shared_dpll (const struct intel_crtc_state *crtc_state);void intel_enable_shared_dpll (const struct intel_crtc_state *crtc_state);void intel_disable_shared_dpll (const struct intel_crtc_state *crtc_state);
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 17/23 drm/i915: Sanitize the shared DPLL find/reference interface
In reply to Imre DeakPass the PLL HW state to the PLL find/reference functions making it clearer what is their input. Also pass to these the atomic state and the CRTC object instead of the CRTC state, since they don't require the latter.
Move setting the PLL in the crtc_state to the get_dpll() hook, which is the more logical place for this, where the related PLL HW state was also set.
This refactoring is also a preparation for a follow-up patch that will have to find/reference multiple PLLs.
No functional changes.
--- drivers/gpu/drm/i915/intel_dpll_mgr.c | 107 +++++++++++++++++--------- 1 file changed, 70 insertions(+), 37 deletions(-)
drivers/gpu/drm/i915/intel_dpll_mgr.c +70 -37
@@ -244,17 +244,18 @@ void intel_disable_shared_dpll(const struct intel_crtc_state *crtc_state) }static struct intel_shared_dpll * -intel_find_shared_dpll (struct intel_crtc_state *crtc_state, +intel_find_shared_dpll (struct intel_atomic_state *state, +const struct intel_crtc *crtc, +const struct intel_dpll_hw_state *pll_state,enum intel_dpll_id range_min,enum intel_dpll_id range_max) { -struct intel_crtc *crtc =to_intel_crtc (crtc_state->base.crtc);struct drm_i915_private *dev_priv =to_i915 (crtc->base.dev);struct intel_shared_dpll *pll, *unused_pll =NULL ;struct intel_shared_dpll_state *shared_dpll;enum intel_dpll_id i; - shared_dpll =intel_atomic_get_shared_dpll_state (crtc_state->base.state); + shared_dpll =intel_atomic_get_shared_dpll_state (&state->base);for (i = range_min; i <= range_max; i++) { pll = &dev_priv->shared_dplls[i];
@@ -266,9 +267,9 @@ intel_find_shared_dpll(struct intel_crtc_state *crtc_state,continue ; } -if (memcmp (&crtc_state->dpll_hw_state, +if (memcmp (pll_state, &shared_dpll[i].hw_state, -sizeof (crtc_state->dpll_hw_state)) ==0 ) { +sizeof (*pll_state)) ==0 ) { DRM_DEBUG_KMS("[CRTC:%d:%s] sharing existing %s (crtc mask 0x%08x, active %x)\n", crtc->base.base.id, crtc->base.name, pll->info->name,
@@ -290,20 +291,19 @@ intel_find_shared_dpll(struct intel_crtc_state *crtc_state, }static void -intel_reference_shared_dpll (struct intel_shared_dpll *pll, -struct intel_crtc_state *crtc_state) +intel_reference_shared_dpll (struct intel_atomic_state *state, +const struct intel_crtc *crtc, +const struct intel_shared_dpll *pll, +const struct intel_dpll_hw_state *pll_state) {struct intel_shared_dpll_state *shared_dpll; -struct intel_crtc *crtc =to_intel_crtc (crtc_state->base.crtc);const enum intel_dpll_id id = pll->info->id; - shared_dpll =intel_atomic_get_shared_dpll_state (crtc_state->base.state); + shared_dpll =intel_atomic_get_shared_dpll_state (&state->base);if (shared_dpll[id].crtc_mask ==0 ) - shared_dpll[id].hw_state = - crtc_state->dpll_hw_state; + shared_dpll[id].hw_state = *pll_state; - crtc_state->shared_dpll = pll;DRM_DEBUG_DRIVER ("using %s for pipe %c\n" , pll->info->name,pipe_name (crtc->pipe));
@@ -463,7 +463,8 @@ static bool ibx_get_dpll(struct intel_atomic_state *state, crtc->base.base.id, crtc->base.name, pll->info->name); }else { - pll =intel_find_shared_dpll (crtc_state, + pll =intel_find_shared_dpll (state, crtc, + &crtc_state->dpll_hw_state,DPLL_ID_PCH_PLL_A ,DPLL_ID_PCH_PLL_B ); }
@@ -472,7 +473,10 @@ static bool ibx_get_dpll(struct intel_atomic_state *state,return false;/* reference the pll */ -intel_reference_shared_dpll (pll, crtc_state); +intel_reference_shared_dpll (state, crtc, + pll, &crtc_state->dpll_hw_state); + + crtc_state->shared_dpll = pll;return true; }
@@ -791,8 +795,12 @@ hsw_ddi_calculate_wrpll(int clock /* in Hz */, *r2_out = best.r2; } -static struct intel_shared_dpll *hsw_ddi_hdmi_get_dpll (struct intel_crtc_state *crtc_state) +static struct intel_shared_dpll * +hsw_ddi_hdmi_get_dpll (struct intel_atomic_state *state, +struct intel_crtc *crtc) { +struct intel_crtc_state *crtc_state = +intel_atomic_get_new_crtc_state (state, crtc);struct intel_shared_dpll *pll;u32 val;unsigned int p, n2, r2;
@@ -805,7 +813,8 @@ static struct intel_shared_dpll *hsw_ddi_hdmi_get_dpll(struct intel_crtc_state * crtc_state->dpll_hw_state.wrpll = val; - pll =intel_find_shared_dpll (crtc_state, + pll =intel_find_shared_dpll (state, crtc, + &crtc_state->dpll_hw_state,DPLL_ID_WRPLL1 ,DPLL_ID_WRPLL2 );if (!pll)
@@ -857,7 +866,7 @@ static bool hsw_get_dpll(struct intel_atomic_state *state, sizeof(crtc_state->dpll_hw_state));if (intel_crtc_has_type (crtc_state,INTEL_OUTPUT_HDMI )) { - pll =hsw_ddi_hdmi_get_dpll (crtc_state); + pll =hsw_ddi_hdmi_get_dpll (state, crtc); }else if (intel_crtc_has_dp_encoder (crtc_state)) { pll =hsw_ddi_dp_get_dpll (crtc_state); }else if (intel_crtc_has_type (crtc_state,INTEL_OUTPUT_ANALOG )) {
@@ -867,7 +876,8 @@ static bool hsw_get_dpll(struct intel_atomic_state *state, crtc_state->dpll_hw_state.spll =SPLL_PLL_ENABLE | SPLL_PLL_FREQ_1350MHz |SPLL_PLL_SSC ; - pll =intel_find_shared_dpll (crtc_state, + pll =intel_find_shared_dpll (state, crtc, + &crtc_state->dpll_hw_state,DPLL_ID_SPLL ,DPLL_ID_SPLL ); }else {return false;
@@ -876,7 +886,10 @@ static bool hsw_get_dpll(struct intel_atomic_state *state,if (!pll)return false; -intel_reference_shared_dpll (pll, crtc_state); +intel_reference_shared_dpll (state, crtc, + pll, &crtc_state->dpll_hw_state); + + crtc_state->shared_dpll = pll;return true; }
@@ -1437,17 +1450,22 @@ static bool skl_get_dpll(struct intel_atomic_state *state, }if (intel_crtc_has_type (crtc_state,INTEL_OUTPUT_EDP )) - pll =intel_find_shared_dpll (crtc_state, + pll =intel_find_shared_dpll (state, crtc, + &crtc_state->dpll_hw_state,DPLL_ID_SKL_DPLL0 ,DPLL_ID_SKL_DPLL0 );else - pll =intel_find_shared_dpll (crtc_state, + pll =intel_find_shared_dpll (state, crtc, + &crtc_state->dpll_hw_state,DPLL_ID_SKL_DPLL1 ,DPLL_ID_SKL_DPLL3 );if (!pll)return false; -intel_reference_shared_dpll (pll, crtc_state); +intel_reference_shared_dpll (state, crtc, + pll, &crtc_state->dpll_hw_state); + + crtc_state->shared_dpll = pll;return true; }
@@ -1880,7 +1898,10 @@ static bool bxt_get_dpll(struct intel_atomic_state *state,DRM_DEBUG_KMS ("[CRTC:%d:%s] using pre-allocated %s\n" , crtc->base.base.id, crtc->base.name, pll->info->name); -intel_reference_shared_dpll (pll, crtc_state); +intel_reference_shared_dpll (state, crtc, + pll, &crtc_state->dpll_hw_state); + + crtc_state->shared_dpll = pll;return true; }
@@ -2395,7 +2416,8 @@ static bool cnl_get_dpll(struct intel_atomic_state *state,return false; } - pll =intel_find_shared_dpll (crtc_state, + pll =intel_find_shared_dpll (state, crtc, + &crtc_state->dpll_hw_state,DPLL_ID_SKL_DPLL0 ,DPLL_ID_SKL_DPLL2 );if (!pll) {
@@ -2403,7 +2425,10 @@ static bool cnl_get_dpll(struct intel_atomic_state *state,return false; } -intel_reference_shared_dpll (pll, crtc_state); +intel_reference_shared_dpll (state, crtc, + pll, &crtc_state->dpll_hw_state); + + crtc_state->shared_dpll = pll;return true; }
@@ -2545,7 +2570,8 @@ static bool icl_calc_tbt_pll(struct intel_crtc_state *crtc_state, }static bool icl_calc_dpll_state (struct intel_crtc_state *crtc_state, -struct intel_encoder *encoder) +struct intel_encoder *encoder, +struct intel_dpll_hw_state *pll_state) {struct drm_i915_private *dev_priv =to_i915 (crtc_state->base.crtc->dev);u32 cfgcr0, cfgcr1;
@@ -2572,11 +2598,10 @@ static bool icl_calc_dpll_state(struct intel_crtc_state *crtc_state,DPLL_CFGCR1_PDIV (pll_params.pdiv) |DPLL_CFGCR1_CENTRAL_FREQ_8400 ; -memset (&crtc_state->dpll_hw_state,0 , -sizeof (crtc_state->dpll_hw_state)); +memset (pll_state,0 ,sizeof (*pll_state)); - crtc_state->dpll_hw_state.cfgcr0 = cfgcr0; - crtc_state->dpll_hw_state.cfgcr1 = cfgcr1; + pll_state->cfgcr0 = cfgcr0; + pll_state->cfgcr1 = cfgcr1;return true; }
@@ -2666,10 +2691,10 @@ static bool icl_mg_pll_find_divisors(int clock_khz, bool is_dp, bool use_ssc,* The specification for this function uses real numbers, so the math had to be * adapted to integer-only calculation, that's why it looks so different. */ -static bool icl_calc_mg_pll_state (struct intel_crtc_state *crtc_state) +static bool icl_calc_mg_pll_state (struct intel_crtc_state *crtc_state, +struct intel_dpll_hw_state *pll_state) {struct drm_i915_private *dev_priv =to_i915 (crtc_state->base.crtc->dev); -struct intel_dpll_hw_state *pll_state = &crtc_state->dpll_hw_state;int refclk_khz = dev_priv->cdclk.hw.ref;int clock = crtc_state->port_clock;u32 dco_khz, m1div, m2div_int, m2div_rem, m2div_frac;
@@ -2847,7 +2872,8 @@ static bool icl_get_dplls(struct intel_atomic_state *state,if (intel_port_is_combophy (dev_priv, port)) { min =DPLL_ID_ICL_DPLL0 ; max =DPLL_ID_ICL_DPLL1 ; - ret =icl_calc_dpll_state (crtc_state, encoder); + ret =icl_calc_dpll_state (crtc_state, encoder, + &crtc_state->dpll_hw_state); }else if (intel_port_is_tc (dev_priv, port)) {if (encoder->type ==INTEL_OUTPUT_DP_MST ) {struct intel_dp_mst_encoder *mst_encoder;
@@ -2861,14 +2887,16 @@ static bool icl_get_dplls(struct intel_atomic_state *state,if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT ) { min =DPLL_ID_ICL_TBTPLL ; max = min; - ret =icl_calc_dpll_state (crtc_state, encoder); + ret =icl_calc_dpll_state (crtc_state, encoder, + &crtc_state->dpll_hw_state); }else {enum tc_port tc_port; tc_port =intel_port_to_tc (dev_priv, port); min =icl_tc_port_to_pll_id (tc_port); max = min; - ret =icl_calc_mg_pll_state (crtc_state); + ret =icl_calc_mg_pll_state (crtc_state, + &crtc_state->dpll_hw_state); } }else {MISSING_CASE (port);
@@ -2881,13 +2909,18 @@ static bool icl_get_dplls(struct intel_atomic_state *state, } - pll =intel_find_shared_dpll (crtc_state, min, max); + pll =intel_find_shared_dpll (state, crtc, + &crtc_state->dpll_hw_state, + min, max);if (!pll) {DRM_DEBUG_KMS ("No PLL selected\n" );return false; } -intel_reference_shared_dpll (pll, crtc_state); +intel_reference_shared_dpll (state, crtc, + pll, &crtc_state->dpll_hw_state); + + crtc_state->shared_dpll = pll;return true; }
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 18/23 drm/i915/icl: Split getting the DPLLs to port type specific functions
In reply to Imre DeakFor clarity factor out the combo PHY and TypeC PHY specific code from icl_get_dplls() into their own functions.
No functional changes.
--- drivers/gpu/drm/i915/intel_dpll_mgr.c | 100 +++++++++++++++++--------- 1 file changed, 66 insertions(+), 34 deletions(-)
drivers/gpu/drm/i915/intel_dpll_mgr.c +66 -34
@@ -2856,51 +2856,66 @@ static bool icl_calc_mg_pll_state(struct intel_crtc_state *crtc_state,return true; } -static bool icl_get_dplls (struct intel_atomic_state *state, -struct intel_crtc *crtc, -struct intel_encoder *encoder) +static bool icl_get_combo_phy_dpll (struct intel_atomic_state *state, +struct intel_crtc *crtc, +struct intel_encoder *encoder) +{ +struct intel_crtc_state *crtc_state = +intel_atomic_get_new_crtc_state (state, crtc); +struct intel_shared_dpll *pll; + +if (!icl_calc_dpll_state (crtc_state, encoder, + &crtc_state->dpll_hw_state)) { +DRM_DEBUG_KMS ("Could not calculate combo PHY PLL state.\n" ); + +return false; + } + + pll =intel_find_shared_dpll (state, crtc, &crtc_state->dpll_hw_state, +DPLL_ID_ICL_DPLL0 , +DPLL_ID_ICL_DPLL1 ); +if (!pll) { +DRM_DEBUG_KMS ("No combo PHY PLL found for port %c\n" , +port_name (encoder->port)); +return false; + } + +intel_reference_shared_dpll (state, crtc, + pll, &crtc_state->dpll_hw_state); + + crtc_state->shared_dpll = pll; + +return true; +} + +static bool icl_get_tc_phy_dplls (struct intel_atomic_state *state, +struct intel_crtc *crtc, +struct intel_encoder *encoder) {struct drm_i915_private *dev_priv =to_i915 (state->base.dev);struct intel_crtc_state *crtc_state =intel_atomic_get_new_crtc_state (state, crtc); -struct intel_digital_port *intel_dig_port; +enum tc_port tc_port =intel_port_to_tc (dev_priv, encoder->port); +struct intel_digital_port *dig_port;struct intel_shared_dpll *pll; -enum port port = encoder->port;enum intel_dpll_id min, max;bool ret; -if (intel_port_is_combophy (dev_priv, port)) { - min =DPLL_ID_ICL_DPLL0 ; - max =DPLL_ID_ICL_DPLL1 ; +if (encoder->type ==INTEL_OUTPUT_DP_MST ) + dig_port =enc_to_mst (&encoder->base)->primary; +else + dig_port =enc_to_dig_port (&encoder->base); + +if (dig_port->tc_mode ==TC_PORT_TBT_ALT ) { + min =DPLL_ID_ICL_TBTPLL ; + max = min; ret =icl_calc_dpll_state (crtc_state, encoder, &crtc_state->dpll_hw_state); - }else if (intel_port_is_tc (dev_priv, port)) { -if (encoder->type ==INTEL_OUTPUT_DP_MST ) { -struct intel_dp_mst_encoder *mst_encoder; - - mst_encoder =enc_to_mst (&encoder->base); - intel_dig_port = mst_encoder->primary; - }else { - intel_dig_port =enc_to_dig_port (&encoder->base); - } - -if (intel_dig_port->tc_mode ==TC_PORT_TBT_ALT ) { - min =DPLL_ID_ICL_TBTPLL ; - max = min; - ret =icl_calc_dpll_state (crtc_state, encoder, - &crtc_state->dpll_hw_state); - }else { -enum tc_port tc_port; - - tc_port =intel_port_to_tc (dev_priv, port); - min =icl_tc_port_to_pll_id (tc_port); - max = min; - ret =icl_calc_mg_pll_state (crtc_state, - &crtc_state->dpll_hw_state); - } }else { -MISSING_CASE (port); -return false; + min =icl_tc_port_to_pll_id (tc_port); + max = min; + ret =icl_calc_mg_pll_state (crtc_state, + &crtc_state->dpll_hw_state); }if (!ret) {
@@ -2925,6 +2940,23 @@ static bool icl_get_dplls(struct intel_atomic_state *state,return true; } +static bool icl_get_dplls (struct intel_atomic_state *state, +struct intel_crtc *crtc, +struct intel_encoder *encoder) +{ +struct drm_i915_private *dev_priv =to_i915 (state->base.dev); +enum port port = encoder->port; + +if (intel_port_is_combophy (dev_priv, port)) +return icl_get_combo_phy_dpll (state, crtc, encoder); +else if (intel_port_is_tc (dev_priv, port)) +return icl_get_tc_phy_dplls (state, crtc, encoder); + +MISSING_CASE (port); + +return false; +} +static bool mg_pll_get_hw_state (struct drm_i915_private *dev_priv,struct intel_shared_dpll *pll,struct intel_dpll_hw_state *hw_state)
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 19/23 drm/i915/icl: Reserve all required PLLs for TypeC ports
In reply to Imre DeakWhen enabling a TypeC port we need to reserve all the required PLLs for it, the TBT PLL for TBT-alt and the MG PHY PLL for DP-alt/legacy sinks. We can select the proper PLL for the current port mode from the reserved PLLs only once we selected and locked down the port mode for the whole duration of the port's active state. Resetting and locking down the port mode can in turn happen only during the modeset commit phase once we disabled the given port and the PLL it used.
To support the above reserve-and-select PLL semantic we store the reserved PLLs along with their HW state in the CRTC state and provide a way to select the active PLL from these. The selected PLL along with its HW state will be pointed at by crtc_state->shared_dpll/dpll_hw_state as in the case of other port types.
Besides reserving all required PLLs no functional changes.
--- drivers/gpu/drm/i915/intel_display.c | 11 +- drivers/gpu/drm/i915/intel_dpll_mgr.c | 152 +++++++++++++++++++------- drivers/gpu/drm/i915/intel_dpll_mgr.h | 9 ++ drivers/gpu/drm/i915/intel_drv.h | 9 ++ 4 files changed, 139 insertions(+), 42 deletions(-)
drivers/gpu/drm/i915/intel_display.c +10 -1
@@ -9878,6 +9878,7 @@ static void icelake_get_ddi_pll(struct drm_i915_private *dev_priv,enum port port, struct intel_crtc_state *pipe_config) { + enum icl_port_dpll_id port_dpll_id;enum intel_dpll_id id;u32 temp;
@@ -9885,22 +9886,28 @@ static void icelake_get_ddi_pll(struct drm_i915_private *dev_priv, temp =I915_READ (DPCLKA_CFGCR0_ICL ) &DPCLKA_CFGCR0_DDI_CLK_SEL_MASK (port); id = temp >>DPCLKA_CFGCR0_DDI_CLK_SEL_SHIFT (port); + port_dpll_id =ICL_PORT_DPLL_DEFAULT ; }else if (intel_port_is_tc (dev_priv, port)) {u32 clk_sel =I915_READ (DDI_CLK_SEL (port)) &DDI_CLK_SEL_MASK ;if (clk_sel ==DDI_CLK_SEL_MG ) { id =icl_tc_port_to_pll_id (intel_port_to_tc (dev_priv, port)); + port_dpll_id =ICL_PORT_DPLL_MG_PHY ; }else {WARN_ON (clk_sel <DDI_CLK_SEL_TBT_162 ); id =DPLL_ID_ICL_TBTPLL ; + port_dpll_id =ICL_PORT_DPLL_DEFAULT ; } }else {WARN (1 ,"Invalid port %x\n" , port);return ; } - pipe_config->shared_dpll =intel_get_shared_dpll_by_id (dev_priv, id); + pipe_config->icl_port_dplls[port_dpll_id].pll = +intel_get_shared_dpll_by_id (dev_priv, id); + +icl_set_active_port_dpll (pipe_config, port_dpll_id); } static void bxt_get_ddi_pll(struct drm_i915_private *dev_priv,
@@ -12037,6 +12044,8 @@ clear_intel_crtc_state(struct intel_crtc_state *crtc_state) saved_state->scaler_state = crtc_state->scaler_state; saved_state->shared_dpll = crtc_state->shared_dpll; saved_state->dpll_hw_state = crtc_state->dpll_hw_state; +memcpy (saved_state->icl_port_dplls, crtc_state->icl_port_dplls, +sizeof (saved_state->icl_port_dplls)); saved_state->crc_enabled = crtc_state->crc_enabled;if (IS_G4X (dev_priv) ||IS_VALLEYVIEW (dev_priv) ||IS_CHERRYVIEW (dev_priv))
drivers/gpu/drm/i915/intel_dpll_mgr.c +111 -41
214 lines not on this page · raw message
drivers/gpu/drm/i915/intel_dpll_mgr.h +9 -0
@@ -141,6 +141,13 @@ enum intel_dpll_id { };#define I915_NUM_PLLS 7 +enum icl_port_dpll_id { +ICL_PORT_DPLL_DEFAULT , +ICL_PORT_DPLL_MG_PHY , + +ICL_PORT_DPLL_COUNT , +}; +struct intel_dpll_hw_state {/* i9xx, pch plls */ u32 dpll;
@@ -337,6 +344,8 @@ bool intel_reserve_shared_dplls(struct intel_atomic_state *state, struct intel_encoder *encoder);void intel_release_shared_dplls (struct intel_atomic_state *state,struct intel_crtc *crtc); +void icl_set_active_port_dpll (struct intel_crtc_state *crtc_state, +enum icl_port_dpll_id port_dpll_id);void intel_prepare_shared_dpll (const struct intel_crtc_state *crtc_state);void intel_enable_shared_dpll (const struct intel_crtc_state *crtc_state);void intel_disable_shared_dpll (const struct intel_crtc_state *crtc_state);
drivers/gpu/drm/i915/intel_drv.h +9 -0
@@ -812,6 +812,15 @@ struct intel_crtc_state {/* Actual register state of the dpll, for shared dpll cross-checking. */ struct intel_dpll_hw_state dpll_hw_state; +/* +* ICL reserved DPLLs for the CRTC/port. The active PLL is selected by +* setting shared_dpll and dpll_hw_state to one of these reserved ones. +*/ +struct icl_port_dpll { +struct intel_shared_dpll *pll; +struct intel_dpll_hw_state hw_state; + } icl_port_dplls[ICL_PORT_DPLL_COUNT ]; +/* DSI PLL registers */ struct {u32 ctrl, div;
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v2 19/23 drm/i915/icl: Reserve all required PLLs for TypeC ports
When enabling a TypeC port we need to reserve all the required PLLs for it, the TBT PLL for TBT-alt and the MG PHY PLL for DP-alt/legacy sinks. We can select the proper PLL for the current port mode from the reserved PLLs only once we selected and locked down the port mode for the whole duration of the port's active state. Resetting and locking down the port mode can in turn happen only during the modeset commit phase once we disabled the given port and the PLL it used.
To support the above reserve-and-select PLL semantic we store the reserved PLLs along with their HW state in the CRTC state and provide a way to select the active PLL from these. The selected PLL along with its HW state will be pointed at by crtc_state->shared_dpll/dpll_hw_state as in the case of other port types.
Besides reserving all required PLLs no functional changes.
v2:
- Fix releasing the ICL PLLs, not clearing the PLLs from the old crtc_state.
--- drivers/gpu/drm/i915/intel_display.c | 11 +- drivers/gpu/drm/i915/intel_dpll_mgr.c | 151 +++++++++++++++++++------- drivers/gpu/drm/i915/intel_dpll_mgr.h | 9 ++ drivers/gpu/drm/i915/intel_drv.h | 9 ++ 4 files changed, 138 insertions(+), 42 deletions(-)
drivers/gpu/drm/i915/intel_display.c +10 -1
@@ -9880,6 +9880,7 @@ static void icelake_get_ddi_pll(struct drm_i915_private *dev_priv,enum port port, struct intel_crtc_state *pipe_config) { + enum icl_port_dpll_id port_dpll_id;enum intel_dpll_id id;u32 temp;
@@ -9887,22 +9888,28 @@ static void icelake_get_ddi_pll(struct drm_i915_private *dev_priv, temp =I915_READ (DPCLKA_CFGCR0_ICL ) &DPCLKA_CFGCR0_DDI_CLK_SEL_MASK (port); id = temp >>DPCLKA_CFGCR0_DDI_CLK_SEL_SHIFT (port); + port_dpll_id =ICL_PORT_DPLL_DEFAULT ; }else if (intel_port_is_tc (dev_priv, port)) {u32 clk_sel =I915_READ (DDI_CLK_SEL (port)) &DDI_CLK_SEL_MASK ;if (clk_sel ==DDI_CLK_SEL_MG ) { id =icl_tc_port_to_pll_id (intel_port_to_tc (dev_priv, port)); + port_dpll_id =ICL_PORT_DPLL_MG_PHY ; }else {WARN_ON (clk_sel <DDI_CLK_SEL_TBT_162 ); id =DPLL_ID_ICL_TBTPLL ; + port_dpll_id =ICL_PORT_DPLL_DEFAULT ; } }else {WARN (1 ,"Invalid port %x\n" , port);return ; } - pipe_config->shared_dpll =intel_get_shared_dpll_by_id (dev_priv, id); + pipe_config->icl_port_dplls[port_dpll_id].pll = +intel_get_shared_dpll_by_id (dev_priv, id); + +icl_set_active_port_dpll (pipe_config, port_dpll_id); } static void bxt_get_ddi_pll(struct drm_i915_private *dev_priv,
@@ -12041,6 +12048,8 @@ clear_intel_crtc_state(struct intel_crtc_state *crtc_state) saved_state->scaler_state = crtc_state->scaler_state; saved_state->shared_dpll = crtc_state->shared_dpll; saved_state->dpll_hw_state = crtc_state->dpll_hw_state; +memcpy (saved_state->icl_port_dplls, crtc_state->icl_port_dplls, +sizeof (saved_state->icl_port_dplls)); saved_state->crc_enabled = crtc_state->crc_enabled;if (IS_G4X (dev_priv) ||IS_VALLEYVIEW (dev_priv) ||IS_CHERRYVIEW (dev_priv))
drivers/gpu/drm/i915/intel_dpll_mgr.c +110 -41
213 lines not on this page · raw message
drivers/gpu/drm/i915/intel_dpll_mgr.h +9 -0
@@ -141,6 +141,13 @@ enum intel_dpll_id { };#define I915_NUM_PLLS 7 +enum icl_port_dpll_id { +ICL_PORT_DPLL_DEFAULT , +ICL_PORT_DPLL_MG_PHY , + +ICL_PORT_DPLL_COUNT , +}; +struct intel_dpll_hw_state {/* i9xx, pch plls */ u32 dpll;
@@ -337,6 +344,8 @@ bool intel_reserve_shared_dplls(struct intel_atomic_state *state, struct intel_encoder *encoder);void intel_release_shared_dplls (struct intel_atomic_state *state,struct intel_crtc *crtc); +void icl_set_active_port_dpll (struct intel_crtc_state *crtc_state, +enum icl_port_dpll_id port_dpll_id);void intel_prepare_shared_dpll (const struct intel_crtc_state *crtc_state);void intel_enable_shared_dpll (const struct intel_crtc_state *crtc_state);void intel_disable_shared_dpll (const struct intel_crtc_state *crtc_state);
drivers/gpu/drm/i915/intel_drv.h +9 -0
@@ -812,6 +812,15 @@ struct intel_crtc_state {/* Actual register state of the dpll, for shared dpll cross-checking. */ struct intel_dpll_hw_state dpll_hw_state; +/* +* ICL reserved DPLLs for the CRTC/port. The active PLL is selected by +* setting shared_dpll and dpll_hw_state to one of these reserved ones. +*/ +struct icl_port_dpll { +struct intel_shared_dpll *pll; +struct intel_dpll_hw_state hw_state; + } icl_port_dplls[ICL_PORT_DPLL_COUNT ]; +/* DSI PLL registers */ struct {u32 ctrl, div;
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH v2 19/23] drm/i915/icl: Reserve all required PLLs for TypeC ports
Quoted 181 lines · Imre Deak
When enabling a TypeC port we need to reserve all the required PLLs for it, the TBT PLL for TBT-alt and the MG PHY PLL for DP-alt/legacy sinks. We can select the proper PLL for the current port mode from the reserved PLLs only once we selected and locked down the port mode for the whole duration of the port's active state. Resetting and locking down the port mode can in turn happen only during the modeset commit phase once we disabled the given port and the PLL it used.
To support the above reserve-and-select PLL semantic we store the reserved PLLs along with their HW state in the CRTC state and provide a way to select the active PLL from these. The selected PLL along with its HW state will be pointed at by crtc_state->shared_dpll/dpll_hw_state as in the case of other port types.
Besides reserving all required PLLs no functional changes.
v2:
- Fix releasing the ICL PLLs, not clearing the PLLs from the oldcrtc_state.Cc Ville Syrjälä <[email protected]>Cc Daniel Vetter <[email protected]>Cc Maarten Lankhorst <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_display.c | 11 +- drivers/gpu/drm/i915/intel_dpll_mgr.c | 151 +++++++++++++++++++------- drivers/gpu/drm/i915/intel_dpll_mgr.h | 9 ++ drivers/gpu/drm/i915/intel_drv.h | 9 ++ 4 files changed, 138 insertions(+), 42 deletions(-)drivers/gpu/drm/i915/intel_display.c +10
-1@@ -9880,6 +9880,7 @@ static void icelake_get_ddi_pll(struct drm_i915_private *dev_priv,enum port port, struct intel_crtc_state *pipe_config) { + enum icl_port_dpll_id port_dpll_id;enum intel_dpll_id id;u32 temp;@@ -9887,22 +9888,28 @@ static void icelake_get_ddi_pll(struct drm_i915_private *dev_priv, temp =I915_READ (DPCLKA_CFGCR0_ICL ) &DPCLKA_CFGCR0_DDI_CLK_SEL_MASK (port); id = temp >>DPCLKA_CFGCR0_DDI_CLK_SEL_SHIFT (port); + port_dpll_id =ICL_PORT_DPLL_DEFAULT ; }else if (intel_port_is_tc (dev_priv, port)) {u32 clk_sel =I915_READ (DDI_CLK_SEL (port)) &DDI_CLK_SEL_MASK ;if (clk_sel ==DDI_CLK_SEL_MG ) { id =icl_tc_port_to_pll_id (intel_port_to_tc (dev_priv, port)); + port_dpll_id =ICL_PORT_DPLL_MG_PHY ; }else {WARN_ON (clk_sel <DDI_CLK_SEL_TBT_162 ); id =DPLL_ID_ICL_TBTPLL ; + port_dpll_id =ICL_PORT_DPLL_DEFAULT ; } }else {WARN (1 ,"Invalid port %x\n" , port);return ; } - pipe_config->shared_dpll =intel_get_shared_dpll_by_id (dev_priv, id); + pipe_config->icl_port_dplls[port_dpll_id].pll = +intel_get_shared_dpll_by_id (dev_priv, id); + +icl_set_active_port_dpll (pipe_config, port_dpll_id); } static void bxt_get_ddi_pll(struct drm_i915_private *dev_priv,@@ -12041,6 +12048,8 @@ clear_intel_crtc_state(struct intel_crtc_state *crtc_state) saved_state->scaler_state = crtc_state->scaler_state; saved_state->shared_dpll = crtc_state->shared_dpll; saved_state->dpll_hw_state = crtc_state->dpll_hw_state; +memcpy (saved_state->icl_port_dplls, crtc_state->icl_port_dplls, +sizeof (saved_state->icl_port_dplls)); saved_state->crc_enabled = crtc_state->crc_enabled;if (IS_G4X (dev_priv) ||IS_VALLEYVIEW (dev_priv) ||IS_CHERRYVIEW (dev_priv))drivers/gpu/drm/i915/intel_dpll_mgr.c +54
-11@@ -2856,34 +2856,79 @@ static bool icl_calc_mg_pll_state(struct intel_crtc_state *crtc_state,return true; } +/** +* icl_set_active_port_dpll - select the active port DPLL for a given CRTC +* @crtc_state: state for the CRTC to select the DPLL for +* @port_dpll_id: the active @port_dpll_id to select +* +* Select the given @port_dpll_id instance from the DPLLs reserved for the +* CRTC. +*/ +void icl_set_active_port_dpll (struct intel_crtc_state *crtc_state, +enum icl_port_dpll_id port_dpll_id) +{ +struct icl_port_dpll *port_dpll = + &crtc_state->icl_port_dplls[port_dpll_id]; + + crtc_state->shared_dpll = port_dpll->pll; + crtc_state->dpll_hw_state = port_dpll->hw_state; +} + +static void icl_update_active_dpll (struct intel_atomic_state *state, +struct intel_crtc *crtc, +struct intel_encoder *encoder) +{ +struct intel_crtc_state *crtc_state = +intel_atomic_get_new_crtc_state (state, crtc); +struct intel_digital_port *primary_port; +enum icl_port_dpll_id port_dpll_id; + + primary_port = encoder->type ==INTEL_OUTPUT_DP_MST ? +enc_to_mst (&encoder->base)->primary : +enc_to_dig_port (&encoder->base); + +switch (primary_port->tc_mode) { +case TC_PORT_TBT_ALT : + port_dpll_id =ICL_PORT_DPLL_DEFAULT ; +break ; +case TC_PORT_DP_ALT : +case TC_PORT_LEGACY : + port_dpll_id =ICL_PORT_DPLL_MG_PHY ; +break ; + } + +icl_set_active_port_dpll (crtc_state, port_dpll_id); +} +static bool icl_get_combo_phy_dpll (struct intel_atomic_state *state,struct intel_crtc *crtc,struct intel_encoder *encoder) {struct intel_crtc_state *crtc_state =intel_atomic_get_new_crtc_state (state, crtc); -struct intel_shared_dpll *pll; +struct icl_port_dpll *port_dpll = + &crtc_state->icl_port_dplls[ICL_PORT_DPLL_DEFAULT ]; -if (!icl_calc_dpll_state (crtc_state, encoder, - &crtc_state->dpll_hw_state)) { +if (!icl_calc_dpll_state (crtc_state, encoder, &port_dpll->hw_state)) {DRM_DEBUG_KMS ("Could not calculate combo PHY PLL state.\n" );return false; } - pll =intel_find_shared_dpll (state, crtc, &crtc_state->dpll_hw_state, -DPLL_ID_ICL_DPLL0 , -DPLL_ID_ICL_DPLL1 ); -if (!pll) { + port_dpll->pll =intel_find_shared_dpll (state, crtc, + &port_dpll->hw_state, +DPLL_ID_ICL_DPLL0 , +DPLL_ID_ICL_DPLL1 ); +if (!port_dpll->pll) {DRM_DEBUG_KMS ("No combo PHY PLL found for port %c\n" ,port_name (encoder->port));return false; }intel_reference_shared_dpll (state, crtc, - pll, &crtc_state->dpll_hw_state); + port_dpll->pll, &port_dpll->hw_state); - crtc_state->shared_dpll = pll; +icl_update_active_dpll (state, crtc, encoder);return true; }@@ -2895,49 +2940,55 @@ static bool icl_get_tc_phy_dplls(struct intel_atomic_state *state,struct drm_i915_private *dev_priv =to_i915 (state->base.dev);struct intel_crtc_state *crtc_state =intel_atomic_get_new_crtc_state (state, crtc); -enum tc_port tc_port =intel_port_to_tc (dev_priv, encoder->port); -struct intel_digital_port *dig_port;
drivers/gpu/drm/i915/intel_dpll_mgr.c static bool icl_get_tc_phy_dplls(struct intel_atomic_state *state, · line 2944
Quoted 10 lines
drivers/gpu/drm/i915/intel_dpll_mgr.c +2
-8-struct intel_shared_dpll *pll; -enum intel_dpll_id min, max; -bool ret; - -if (encoder->type ==INTEL_OUTPUT_DP_MST ) - dig_port =enc_to_mst (&encoder->base)->primary; -else - dig_port =enc_to_dig_port (&encoder->base); +struct icl_port_dpll *port_dpll = + &crtc_state->icl_port_dplls[ICL_PORT_DPLL_DEFAULT ];
I would move that initialization next to the code so that the tbt vs. mg cases look more like twins.
Quoted 145 lines
drivers/gpu/drm/i915/intel_dpll_mgr.c +54
-22+enum intel_dpll_id dpll_id; -if (dig_port->tc_mode ==TC_PORT_TBT_ALT ) { - min =DPLL_ID_ICL_TBTPLL ; - max = min; - ret =icl_calc_dpll_state (crtc_state, encoder, - &crtc_state->dpll_hw_state); - }else { - min =icl_tc_port_to_pll_id (tc_port); - max = min; - ret =icl_calc_mg_pll_state (crtc_state, - &crtc_state->dpll_hw_state); +if (!icl_calc_dpll_state (crtc_state, encoder, &port_dpll->hw_state)) { +DRM_DEBUG_KMS ("Could not calculate TBT PLL state.\n" ); +return false; } -if (!ret) { -DRM_DEBUG_KMS ("Could not calculate PLL state.\n" ); + port_dpll->pll =intel_find_shared_dpll (state, crtc, + &port_dpll->hw_state, +DPLL_ID_ICL_TBTPLL , +DPLL_ID_ICL_TBTPLL ); +if (!port_dpll->pll) { +DRM_DEBUG_KMS ("No TBT-ALT PLL found\n" );return false; } +intel_reference_shared_dpll (state, crtc, + port_dpll->pll, &port_dpll->hw_state); - pll =intel_find_shared_dpll (state, crtc, - &crtc_state->dpll_hw_state, - min, max); -if (!pll) { -DRM_DEBUG_KMS ("No PLL selected\n" ); -return false; + port_dpll = &crtc_state->icl_port_dplls[ICL_PORT_DPLL_MG_PHY ]; +if (!icl_calc_mg_pll_state (crtc_state, &port_dpll->hw_state)) { +DRM_DEBUG_KMS ("Could not calculate MG PHY PLL state.\n" ); + goto err_unreference_tbt_pll; } + dpll_id =icl_tc_port_to_pll_id (intel_port_to_tc (dev_priv, + encoder->port)); + port_dpll->pll =intel_find_shared_dpll (state, crtc, + &port_dpll->hw_state, + dpll_id, + dpll_id); +if (!port_dpll->pll) { +DRM_DEBUG_KMS ("No MG PHY PLL found\n" ); + goto err_unreference_tbt_pll; + }intel_reference_shared_dpll (state, crtc, - pll, &crtc_state->dpll_hw_state); + port_dpll->pll, &port_dpll->hw_state); - crtc_state->shared_dpll = pll; +icl_update_active_dpll (state, crtc, encoder);return true; + +err_unreference_tbt_pll: + port_dpll = &crtc_state->icl_port_dplls[ICL_PORT_DPLL_DEFAULT ]; +intel_unreference_shared_dpll (state, crtc, port_dpll->pll); + +return false; } static bool icl_get_dplls(struct intel_atomic_state *state,@@ -2957,6 +3008,24 @@ static bool icl_get_dplls(struct intel_atomic_state *state,return false; } +static void icl_put_dplls (struct intel_atomic_state *state, +struct intel_crtc *crtc) +{ +struct intel_crtc_state *crtc_state = +intel_atomic_get_old_crtc_state (state, crtc); +enum icl_port_dpll_id id; + +for (id =ICL_PORT_DPLL_DEFAULT ; id <ICL_PORT_DPLL_COUNT ; id++) { +struct icl_port_dpll *port_dpll = + &crtc_state->icl_port_dplls[id]; + +if (!port_dpll->pll) +continue ; + +intel_unreference_shared_dpll (state, crtc, port_dpll->pll); + } +} +static bool mg_pll_get_hw_state (struct drm_i915_private *dev_priv,struct intel_shared_dpll *pll,struct intel_dpll_hw_state *hw_state)@@ -3330,7 +3399,7 @@ static const struct dpll_info icl_plls[] = {static const struct intel_dpll_mgr icl_pll_mgr = { .dpll_info = icl_plls, .get_dplls = icl_get_dplls, - .put_dplls = intel_put_dpll, + .put_dplls = icl_put_dplls, .dump_hw_state = icl_dump_hw_state, };@@ -3343,7 +3412,7 @@ static const struct dpll_info ehl_plls[] = {static const struct intel_dpll_mgr ehl_pll_mgr = { .dpll_info = ehl_plls, .get_dplls = icl_get_dplls, - .put_dplls = intel_put_dpll, + .put_dplls = icl_put_dplls, .dump_hw_state = icl_dump_hw_state, };drivers/gpu/drm/i915/intel_dpll_mgr.h +9
-0@@ -141,6 +141,13 @@ enum intel_dpll_id { };#define I915_NUM_PLLS 7 +enum icl_port_dpll_id { +ICL_PORT_DPLL_DEFAULT , +ICL_PORT_DPLL_MG_PHY , + +ICL_PORT_DPLL_COUNT , +}; +struct intel_dpll_hw_state {/* i9xx, pch plls */ u32 dpll;@@ -337,6 +344,8 @@ bool intel_reserve_shared_dplls(struct intel_atomic_state *state, struct intel_encoder *encoder);void intel_release_shared_dplls (struct intel_atomic_state *state,struct intel_crtc *crtc); +void icl_set_active_port_dpll (struct intel_crtc_state *crtc_state, +enum icl_port_dpll_id port_dpll_id);void intel_prepare_shared_dpll (const struct intel_crtc_state *crtc_state);void intel_enable_shared_dpll (const struct intel_crtc_state *crtc_state);void intel_disable_shared_dpll (const struct intel_crtc_state *crtc_state);drivers/gpu/drm/i915/intel_drv.h +0
-0
drivers/gpu/drm/i915/intel_drv.h struct intel_crtc_state { · line 821
Quoted 10 lines
drivers/gpu/drm/i915/intel_drv.h +7
-0@@ -812,6 +812,15 @@ struct intel_crtc_state {/* Actual register state of the dpll, for shared dpll cross-checking. */ struct intel_dpll_hw_state dpll_hw_state; +/* +* ICL reserved DPLLs for the CRTC/port. The active PLL is selected by +* setting shared_dpll and dpll_hw_state to one of these reserved ones. +*/ +struct icl_port_dpll { +struct intel_shared_dpll *pll; +struct intel_dpll_hw_state hw_state;
I was pondering if we should use this array on non-icl too. Would avoid having three instances of this state embedded in our crtc state. But I don't know how big the struct is so not sure if it's worth it.
Anyways, something to think about for a future optimization.
Quoted 7 lines
drivers/gpu/drm/i915/intel_drv.h +2
-0+ } icl_port_dplls[ICL_PORT_DPLL_COUNT ]; +/* DSI PLL registers */ struct {u32 ctrl, div;Signature · 1 line
2.17.1
Signature · 6 lines
Ville Syrjälä Intel _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH v2 19/23] drm/i915/icl: Reserve all required PLLs for TypeC ports
Quoted 187 lines · Ville Syrjälä
Quoted 186 lines · Imre Deak
When enabling a TypeC port we need to reserve all the required PLLs for it, the TBT PLL for TBT-alt and the MG PHY PLL for DP-alt/legacy sinks. We can select the proper PLL for the current port mode from the reserved PLLs only once we selected and locked down the port mode for the whole duration of the port's active state. Resetting and locking down the port mode can in turn happen only during the modeset commit phase once we disabled the given port and the PLL it used.
To support the above reserve-and-select PLL semantic we store the reserved PLLs along with their HW state in the CRTC state and provide a way to select the active PLL from these. The selected PLL along with its HW state will be pointed at by crtc_state->shared_dpll/dpll_hw_state as in the case of other port types.
Besides reserving all required PLLs no functional changes.
v2:
- Fix releasing the ICL PLLs, not clearing the PLLs from the oldcrtc_state.Cc Ville Syrjälä <[email protected]>Cc Daniel Vetter <[email protected]>Cc Maarten Lankhorst <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_display.c | 11 +- drivers/gpu/drm/i915/intel_dpll_mgr.c | 151 +++++++++++++++++++------- drivers/gpu/drm/i915/intel_dpll_mgr.h | 9 ++ drivers/gpu/drm/i915/intel_drv.h | 9 ++ 4 files changed, 138 insertions(+), 42 deletions(-)drivers/gpu/drm/i915/intel_display.c +10
-1@@ -9880,6 +9880,7 @@ static void icelake_get_ddi_pll(struct drm_i915_private *dev_priv,enum port port, struct intel_crtc_state *pipe_config) { + enum icl_port_dpll_id port_dpll_id;enum intel_dpll_id id;u32 temp;@@ -9887,22 +9888,28 @@ static void icelake_get_ddi_pll(struct drm_i915_private *dev_priv, temp =I915_READ (DPCLKA_CFGCR0_ICL ) &DPCLKA_CFGCR0_DDI_CLK_SEL_MASK (port); id = temp >>DPCLKA_CFGCR0_DDI_CLK_SEL_SHIFT (port); + port_dpll_id =ICL_PORT_DPLL_DEFAULT ; }else if (intel_port_is_tc (dev_priv, port)) {u32 clk_sel =I915_READ (DDI_CLK_SEL (port)) &DDI_CLK_SEL_MASK ;if (clk_sel ==DDI_CLK_SEL_MG ) { id =icl_tc_port_to_pll_id (intel_port_to_tc (dev_priv, port)); + port_dpll_id =ICL_PORT_DPLL_MG_PHY ; }else {WARN_ON (clk_sel <DDI_CLK_SEL_TBT_162 ); id =DPLL_ID_ICL_TBTPLL ; + port_dpll_id =ICL_PORT_DPLL_DEFAULT ; } }else {WARN (1 ,"Invalid port %x\n" , port);return ; } - pipe_config->shared_dpll =intel_get_shared_dpll_by_id (dev_priv, id); + pipe_config->icl_port_dplls[port_dpll_id].pll = +intel_get_shared_dpll_by_id (dev_priv, id); + +icl_set_active_port_dpll (pipe_config, port_dpll_id); } static void bxt_get_ddi_pll(struct drm_i915_private *dev_priv,@@ -12041,6 +12048,8 @@ clear_intel_crtc_state(struct intel_crtc_state *crtc_state) saved_state->scaler_state = crtc_state->scaler_state; saved_state->shared_dpll = crtc_state->shared_dpll; saved_state->dpll_hw_state = crtc_state->dpll_hw_state; +memcpy (saved_state->icl_port_dplls, crtc_state->icl_port_dplls, +sizeof (saved_state->icl_port_dplls)); saved_state->crc_enabled = crtc_state->crc_enabled;if (IS_G4X (dev_priv) ||IS_VALLEYVIEW (dev_priv) ||IS_CHERRYVIEW (dev_priv))drivers/gpu/drm/i915/intel_dpll_mgr.c +54
-16@@ -2856,34 +2856,79 @@ static bool icl_calc_mg_pll_state(struct intel_crtc_state *crtc_state,return true; } +/** +* icl_set_active_port_dpll - select the active port DPLL for a given CRTC +* @crtc_state: state for the CRTC to select the DPLL for +* @port_dpll_id: the active @port_dpll_id to select +* +* Select the given @port_dpll_id instance from the DPLLs reserved for the +* CRTC. +*/ +void icl_set_active_port_dpll (struct intel_crtc_state *crtc_state, +enum icl_port_dpll_id port_dpll_id) +{ +struct icl_port_dpll *port_dpll = + &crtc_state->icl_port_dplls[port_dpll_id]; + + crtc_state->shared_dpll = port_dpll->pll; + crtc_state->dpll_hw_state = port_dpll->hw_state; +} + +static void icl_update_active_dpll (struct intel_atomic_state *state, +struct intel_crtc *crtc, +struct intel_encoder *encoder) +{ +struct intel_crtc_state *crtc_state = +intel_atomic_get_new_crtc_state (state, crtc); +struct intel_digital_port *primary_port; +enum icl_port_dpll_id port_dpll_id; + + primary_port = encoder->type ==INTEL_OUTPUT_DP_MST ? +enc_to_mst (&encoder->base)->primary : +enc_to_dig_port (&encoder->base); + +switch (primary_port->tc_mode) { +case TC_PORT_TBT_ALT : + port_dpll_id =ICL_PORT_DPLL_DEFAULT ; +break ; +case TC_PORT_DP_ALT : +case TC_PORT_LEGACY : + port_dpll_id =ICL_PORT_DPLL_MG_PHY ; +break ; + } + +icl_set_active_port_dpll (crtc_state, port_dpll_id); +} +static bool icl_get_combo_phy_dpll (struct intel_atomic_state *state,struct intel_crtc *crtc,struct intel_encoder *encoder) {struct intel_crtc_state *crtc_state =intel_atomic_get_new_crtc_state (state, crtc); -struct intel_shared_dpll *pll; +struct icl_port_dpll *port_dpll = + &crtc_state->icl_port_dplls[ICL_PORT_DPLL_DEFAULT ]; -if (!icl_calc_dpll_state (crtc_state, encoder, - &crtc_state->dpll_hw_state)) { +if (!icl_calc_dpll_state (crtc_state, encoder, &port_dpll->hw_state)) {DRM_DEBUG_KMS ("Could not calculate combo PHY PLL state.\n" );return false; } - pll =intel_find_shared_dpll (state, crtc, &crtc_state->dpll_hw_state, -DPLL_ID_ICL_DPLL0 , -DPLL_ID_ICL_DPLL1 ); -if (!pll) { + port_dpll->pll =intel_find_shared_dpll (state, crtc, + &port_dpll->hw_state, +DPLL_ID_ICL_DPLL0 , +DPLL_ID_ICL_DPLL1 ); +if (!port_dpll->pll) {DRM_DEBUG_KMS ("No combo PHY PLL found for port %c\n" ,port_name (encoder->port));return false; }intel_reference_shared_dpll (state, crtc, - pll, &crtc_state->dpll_hw_state); + port_dpll->pll, &port_dpll->hw_state); - crtc_state->shared_dpll = pll; +icl_update_active_dpll (state, crtc, encoder);return true; }@@ -2895,49 +2940,55 @@ static bool icl_get_tc_phy_dplls(struct intel_atomic_state *state,struct drm_i915_private *dev_priv =to_i915 (state->base.dev);struct intel_crtc_state *crtc_state =intel_atomic_get_new_crtc_state (state, crtc); -enum tc_port tc_port =intel_port_to_tc (dev_priv, encoder->port); -struct intel_digital_port *dig_port; -struct intel_shared_dpll *pll; -enum intel_dpll_id min, max; -bool ret; - -if (encoder->type ==INTEL_OUTPUT_DP_MST )
Quoted 8 lines
drivers/gpu/drm/i915/intel_dpll_mgr.c static bool icl_get_tc_phy_dplls(struct intel_atomic_state *state, · line 2944
Quoted 5 lines
drivers/gpu/drm/i915/intel_dpll_mgr.c +2
-3- dig_port =enc_to_mst (&encoder->base)->primary; - else - dig_port =enc_to_dig_port (&encoder->base); +struct icl_port_dpll *port_dpll = + &crtc_state->icl_port_dplls[ICL_PORT_DPLL_DEFAULT ];I would move that initialization next to the code so that the tbt vs. mg cases look more like twins.
Ok.
Quoted 162 lines
Quoted 146 lines
drivers/gpu/drm/i915/intel_dpll_mgr.c +54
-22+enum intel_dpll_id dpll_id; -if (dig_port->tc_mode ==TC_PORT_TBT_ALT ) { - min =DPLL_ID_ICL_TBTPLL ; - max = min; - ret =icl_calc_dpll_state (crtc_state, encoder, - &crtc_state->dpll_hw_state); - }else { - min =icl_tc_port_to_pll_id (tc_port); - max = min; - ret =icl_calc_mg_pll_state (crtc_state, - &crtc_state->dpll_hw_state); +if (!icl_calc_dpll_state (crtc_state, encoder, &port_dpll->hw_state)) { +DRM_DEBUG_KMS ("Could not calculate TBT PLL state.\n" ); +return false; } -if (!ret) { -DRM_DEBUG_KMS ("Could not calculate PLL state.\n" ); + port_dpll->pll =intel_find_shared_dpll (state, crtc, + &port_dpll->hw_state, +DPLL_ID_ICL_TBTPLL , +DPLL_ID_ICL_TBTPLL ); +if (!port_dpll->pll) { +DRM_DEBUG_KMS ("No TBT-ALT PLL found\n" );return false; } +intel_reference_shared_dpll (state, crtc, + port_dpll->pll, &port_dpll->hw_state); - pll =intel_find_shared_dpll (state, crtc, - &crtc_state->dpll_hw_state, - min, max); -if (!pll) { -DRM_DEBUG_KMS ("No PLL selected\n" ); -return false; + port_dpll = &crtc_state->icl_port_dplls[ICL_PORT_DPLL_MG_PHY ]; +if (!icl_calc_mg_pll_state (crtc_state, &port_dpll->hw_state)) { +DRM_DEBUG_KMS ("Could not calculate MG PHY PLL state.\n" ); + goto err_unreference_tbt_pll; } + dpll_id =icl_tc_port_to_pll_id (intel_port_to_tc (dev_priv, + encoder->port)); + port_dpll->pll =intel_find_shared_dpll (state, crtc, + &port_dpll->hw_state, + dpll_id, + dpll_id); +if (!port_dpll->pll) { +DRM_DEBUG_KMS ("No MG PHY PLL found\n" ); + goto err_unreference_tbt_pll; + }intel_reference_shared_dpll (state, crtc, - pll, &crtc_state->dpll_hw_state); + port_dpll->pll, &port_dpll->hw_state); - crtc_state->shared_dpll = pll; +icl_update_active_dpll (state, crtc, encoder);return true; + +err_unreference_tbt_pll: + port_dpll = &crtc_state->icl_port_dplls[ICL_PORT_DPLL_DEFAULT ]; +intel_unreference_shared_dpll (state, crtc, port_dpll->pll); + +return false; } static bool icl_get_dplls(struct intel_atomic_state *state,@@ -2957,6 +3008,24 @@ static bool icl_get_dplls(struct intel_atomic_state *state,return false; } +static void icl_put_dplls (struct intel_atomic_state *state, +struct intel_crtc *crtc) +{ +struct intel_crtc_state *crtc_state = +intel_atomic_get_old_crtc_state (state, crtc); +enum icl_port_dpll_id id; + +for (id =ICL_PORT_DPLL_DEFAULT ; id <ICL_PORT_DPLL_COUNT ; id++) { +struct icl_port_dpll *port_dpll = + &crtc_state->icl_port_dplls[id]; + +if (!port_dpll->pll) +continue ; + +intel_unreference_shared_dpll (state, crtc, port_dpll->pll); + } +} +static bool mg_pll_get_hw_state (struct drm_i915_private *dev_priv,struct intel_shared_dpll *pll,struct intel_dpll_hw_state *hw_state)@@ -3330,7 +3399,7 @@ static const struct dpll_info icl_plls[] = {static const struct intel_dpll_mgr icl_pll_mgr = { .dpll_info = icl_plls, .get_dplls = icl_get_dplls, - .put_dplls = intel_put_dpll, + .put_dplls = icl_put_dplls, .dump_hw_state = icl_dump_hw_state, };@@ -3343,7 +3412,7 @@ static const struct dpll_info ehl_plls[] = {static const struct intel_dpll_mgr ehl_pll_mgr = { .dpll_info = ehl_plls, .get_dplls = icl_get_dplls, - .put_dplls = intel_put_dpll, + .put_dplls = icl_put_dplls, .dump_hw_state = icl_dump_hw_state, };drivers/gpu/drm/i915/intel_dpll_mgr.h +9
-0@@ -141,6 +141,13 @@ enum intel_dpll_id { };#define I915_NUM_PLLS 7 +enum icl_port_dpll_id { +ICL_PORT_DPLL_DEFAULT , +ICL_PORT_DPLL_MG_PHY , + +ICL_PORT_DPLL_COUNT , +}; +struct intel_dpll_hw_state {/* i9xx, pch plls */ u32 dpll;@@ -337,6 +344,8 @@ bool intel_reserve_shared_dplls(struct intel_atomic_state *state, struct intel_encoder *encoder);void intel_release_shared_dplls (struct intel_atomic_state *state,struct intel_crtc *crtc); +void icl_set_active_port_dpll (struct intel_crtc_state *crtc_state, +enum icl_port_dpll_id port_dpll_id);void intel_prepare_shared_dpll (const struct intel_crtc_state *crtc_state);void intel_enable_shared_dpll (const struct intel_crtc_state *crtc_state);void intel_disable_shared_dpll (const struct intel_crtc_state *crtc_state);drivers/gpu/drm/i915/intel_drv.h +0
-0drivers/gpu/drm/i915/intel_drv.h struct intel_crtc_state { · line 821
Quoted 10 lines
drivers/gpu/drm/i915/intel_drv.h +7
-0@@ -812,6 +812,15 @@ struct intel_crtc_state {/* Actual register state of the dpll, for shared dpll cross-checking. */ struct intel_dpll_hw_state dpll_hw_state; +/* +* ICL reserved DPLLs for the CRTC/port. The active PLL is selected by +* setting shared_dpll and dpll_hw_state to one of these reserved ones. +*/ +struct icl_port_dpll { +struct intel_shared_dpll *pll; +struct intel_dpll_hw_state hw_state;I was pondering if we should use this array on non-icl too. Would avoid having three instances of this state embedded in our crtc state. But I don't know how big the struct is so not sure if it's worth it.
Quoted 1 line
Anyways, something to think about for a future optimization.
Yep, would be good to make it more generic, expressing it also better that hw_state is pll's state.
I suppose that would be instead of the above
struct intel_port_dpll {
struct intel_shared_dpll *pll;
struct intel_dpll_hw_state hw_state;
} port_dplls[PORT_DPLL_COUNT];
struct intel_port_dpll *active_dpll;removing also intel_crtc_state::dpll_hw_state and shared_dpll.
I chickened out of doing that too now, affecting many platforms, but would be worth doing as a follow-up.
Quoted 12 lines
Quoted 8 lines
drivers/gpu/drm/i915/intel_drv.h +2
-0+ } icl_port_dplls[ICL_PORT_DPLL_COUNT ]; +/* DSI PLL registers */ struct {u32 ctrl, div;Signature · 1 line
2.17.1Signature · 2 lines
Ville Syrjälä Intel
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 20/23 drm/i915: Keep the TypeC port mode fixed when the port is active
In reply to Imre DeakThe TypeC port mode needs to stay fixed whenever the port is active. Do that by introducing a tc_link_refcount to account for active ports, avoiding changing the port mode if a reference is held.
During the modeset commit phase we also have to reset the port mode and update the active PLL reflecting the new port mode. We can do this only once the port and its old PLL has been already disabled. Add the new connector_update_prepare/complete hooks that are called around the whole enabling sequence. The TypeC specific hooks of these will reset the port mode, update the active PLL if the port will be active and ensure that the port mode will stay fixed for the duration of the whole enabling sequence by holding a tc_link_refcount.
During the port enabling, the pre_pll_enable/post_pll_disable hooks will take/release a tc_link_refcount to ensure the port mode stays fixed while the port is active.
Changing the port mode should also be avoided during connector detection and AUX transfers if the port is active, we'll do that by checking the port's tc_link_refcount.
When resetting the port mode we also have to take into account the maximum lanes provided by the FIA. It's guaranteed to be 4 in TBT-alt and legacy modes, but there may be less lanes available in DP-alt mode, in which case we have to fall back to TBT-alt mode.
While at it also update icl_tc_phy_connect()'s code comment, reflecting the current way of switching the port mode.
--- drivers/gpu/drm/i915/intel_ddi.c | 46 +++++++++++-- drivers/gpu/drm/i915/intel_ddi.h | 7 ++ drivers/gpu/drm/i915/intel_display.c | 90 +++++++++++++++++++++++++- drivers/gpu/drm/i915/intel_dp.c | 7 ++ drivers/gpu/drm/i915/intel_dp_mst.c | 6 ++ drivers/gpu/drm/i915/intel_dpll_mgr.c | 28 +++++++- drivers/gpu/drm/i915/intel_dpll_mgr.h | 3 + drivers/gpu/drm/i915/intel_drv.h | 9 +++ drivers/gpu/drm/i915/intel_hdmi.c | 7 ++ drivers/gpu/drm/i915/intel_tc.c | 93 ++++++++++++++++++++------- drivers/gpu/drm/i915/intel_tc.h | 3 + 11 files changed, 269 insertions(+), 30 deletions(-)
drivers/gpu/drm/i915/intel_ddi.c +42 -4
@@ -3610,6 +3610,38 @@ static void intel_ddi_set_fia_lane_count(struct intel_encoder *encoder,I915_WRITE (PORT_TX_DFLEXDPMLE1 , val); } +void +intel_ddi_connector_update_prepare (struct intel_atomic_state *state, +struct intel_connector *connector) +{ +struct drm_connector_state *conn_state = +drm_atomic_get_new_connector_state (&state->base, + &connector->base); +struct intel_crtc *crtc = conn_state->crtc ? +to_intel_crtc (conn_state->crtc) :NULL ; +struct intel_crtc_state *crtc_state = + crtc ?intel_atomic_get_new_crtc_state (state, crtc) :NULL ; +struct intel_digital_port *primary_port = +intel_connector_primary_digital_port (connector); +int required_lanes = crtc_state ? crtc_state->lane_count :1 ; + +WARN_ON (crtc && crtc->active); + +intel_tc_port_get_link (primary_port, required_lanes); +if (crtc_state && crtc_state->base.active) +intel_update_active_dpll (state, crtc, &primary_port->base); +} + +void +intel_ddi_connector_update_complete (struct intel_atomic_state *state, +struct intel_connector *connector) +{ +struct intel_digital_port *primary_port = +intel_connector_primary_digital_port (connector); + +intel_tc_port_put_link (primary_port); +} + static void intel_ddi_pre_pll_enable(struct intel_encoder *encoder, const struct intel_crtc_state *crtc_state,
@@ -3617,10 +3649,13 @@ intel_ddi_pre_pll_enable(struct intel_encoder *encoder, {struct drm_i915_private *dev_priv =to_i915 (encoder->base.dev);struct intel_digital_port *dig_port =enc_to_dig_port (&encoder->base); +bool is_tc_port =intel_port_is_tc (dev_priv, encoder->port);enum port port = encoder->port; -if (intel_crtc_has_dp_encoder (crtc_state) || -intel_port_is_tc (dev_priv, encoder->port)) +if (is_tc_port) +intel_tc_port_get_link (dig_port, crtc_state->lane_count); + +if (intel_crtc_has_dp_encoder (crtc_state) || is_tc_port)intel_display_power_get (dev_priv,intel_ddi_main_link_aux_domain (dig_port));
@@ -3645,11 +3680,14 @@ intel_ddi_post_pll_disable(struct intel_encoder *encoder, {struct drm_i915_private *dev_priv =to_i915 (encoder->base.dev);struct intel_digital_port *dig_port =enc_to_dig_port (&encoder->base); +bool is_tc_port =intel_port_is_tc (dev_priv, encoder->port); -if (intel_crtc_has_dp_encoder (crtc_state) || -intel_port_is_tc (dev_priv, encoder->port)) +if (intel_crtc_has_dp_encoder (crtc_state) || is_tc_port)intel_display_power_put_unchecked (dev_priv,intel_ddi_main_link_aux_domain (dig_port)); + +if (is_tc_port) +intel_tc_port_put_link (dig_port); }void intel_ddi_prepare_link_retrain (struct intel_dp *intel_dp)
drivers/gpu/drm/i915/intel_ddi.h +7 -0
@@ -12,6 +12,7 @@struct drm_connector_state ;struct drm_i915_private ; +struct intel_atomic_state ;struct intel_connector ;struct intel_crtc ;struct intel_crtc_state ;
@@ -35,6 +36,12 @@ void intel_ddi_prepare_link_retrain(struct intel_dp *intel_dp);bool intel_ddi_connector_get_hw_state (struct intel_connector *intel_connector);void intel_ddi_get_config (struct intel_encoder *encoder,struct intel_crtc_state *pipe_config); +void +intel_ddi_connector_update_prepare (struct intel_atomic_state *state, +struct intel_connector *connector); +void +intel_ddi_connector_update_complete (struct intel_atomic_state *state, +struct intel_connector *connector);void intel_ddi_set_vc_payload_alloc (const struct intel_crtc_state *crtc_state,bool state); void intel_ddi_compute_min_voltage_level(struct drm_i915_private *dev_priv,
drivers/gpu/drm/i915/intel_display.c +89 -1
121 lines not on this page · raw message
drivers/gpu/drm/i915/intel_dp.c +7 -0
@@ -7195,6 +7195,13 @@ intel_dp_init_connector(struct intel_digital_port *intel_dig_port,else intel_connector->get_hw_state = intel_connector_get_hw_state; +if (intel_port_is_tc (dev_priv, intel_encoder->port)) { + intel_connector->update_prepare = + intel_ddi_connector_update_prepare; + intel_connector->update_complete = + intel_ddi_connector_update_complete; + } +/* init MST on ports that can support it */ if (HAS_DP_MST(dev_priv) && !intel_dp_is_edp(intel_dp) && (port == PORT_B || port == PORT_C ||
drivers/gpu/drm/i915/intel_dp_mst.c +6 -0
@@ -505,6 +505,12 @@ static struct drm_connector *intel_dp_add_mst_connector(struct drm_dp_mst_topoloif (!intel_connector)return NULL ; +if (intel_port_is_tc (dev_priv, intel_dig_port->base.port)) { + intel_connector->update_prepare = + intel_ddi_connector_update_prepare; + intel_connector->update_complete = + intel_ddi_connector_update_complete; + } intel_connector->get_hw_state = intel_dp_mst_get_hw_state; intel_connector->mst_port = intel_dp; intel_connector->port = port;
drivers/gpu/drm/i915/intel_dpll_mgr.c +27 -1
@@ -1939,7 +1939,9 @@ struct intel_dpll_mgr { struct intel_encoder *encoder);void (*put_dplls)(struct intel_atomic_state *state,struct intel_crtc *crtc); - +void (*update_active_dpll)(struct intel_atomic_state *state, +struct intel_crtc *crtc, +struct intel_encoder *encoder);void (*dump_hw_state)(struct drm_i915_private *dev_priv,const struct intel_dpll_hw_state *hw_state); };
@@ -3401,6 +3403,7 @@ static const struct intel_dpll_mgr icl_pll_mgr = { .dpll_info = icl_plls, .get_dplls = icl_get_dplls, .put_dplls = icl_put_dplls, + .update_active_dpll = icl_update_active_dpll, .dump_hw_state = icl_dump_hw_state, };
@@ -3525,6 +3528,29 @@ void intel_release_shared_dplls(struct intel_atomic_state *state, dpll_mgr->put_dplls (state, crtc); } +/** +* intel_update_active_dpll - update the active DPLL for a CRTC/encoder +* @state: atomic state +* @crtc: the CRTC for which to update the active DPLL +* @encoder: encoder determining the type of port DPLL +* +* Update the active DPLL for the given @crtc/@encoder in @crtc's atomic state, +* from the port DPLLs reserved previously by intel_reserve_shared_dplls(). The +* DPLL selected will be based on the current mode of the encoder's port. +*/ +void intel_update_active_dpll (struct intel_atomic_state *state, +struct intel_crtc *crtc, +struct intel_encoder *encoder) +{ +struct drm_i915_private *dev_priv =to_i915 (encoder->base.dev); +const struct intel_dpll_mgr *dpll_mgr = dev_priv->dpll_mgr; + +if (WARN_ON (!dpll_mgr)) +return ; + + dpll_mgr->update_active_dpll (state, crtc, encoder); +} +/** * intel_shared_dpll_dump_hw_state - write hw_state to dmesg * @dev_priv: i915 drm device
drivers/gpu/drm/i915/intel_dpll_mgr.h +3 -0
@@ -346,6 +346,9 @@ void intel_release_shared_dplls(struct intel_atomic_state *state, struct intel_crtc *crtc);void icl_set_active_port_dpll (struct intel_crtc_state *crtc_state,enum icl_port_dpll_id port_dpll_id); +void intel_update_active_dpll (struct intel_atomic_state *state, +struct intel_crtc *crtc, +struct intel_encoder *encoder);void intel_prepare_shared_dpll (const struct intel_crtc_state *crtc_state);void intel_enable_shared_dpll (const struct intel_crtc_state *crtc_state);void intel_disable_shared_dpll (const struct intel_crtc_state *crtc_state);
drivers/gpu/drm/i915/intel_drv.h +9 -0
@@ -375,6 +375,11 @@ struct intel_connector {* and active (i.e. dpms ON state). */ bool (*get_hw_state)(struct intel_connector *); +void (*update_prepare)(struct intel_atomic_state *state, +struct intel_connector *connector); +void (*update_complete)(struct intel_atomic_state *state, +struct intel_connector *connector); +/* Panel info for eDP and LVDS */ struct intel_panel panel;
@@ -1234,6 +1239,8 @@ struct intel_digital_port {enum aux_ch aux_ch;enum intel_display_power_domain ddi_io_power_domain;struct mutex tc_lock; +intel_wakeref_t tc_lock_wakeref; +int tc_link_refcount; bool tc_legacy_port:1;enum tc_port_mode tc_mode;
@@ -1485,6 +1492,8 @@ void intel_pps_unlock_regs_wa(struct drm_i915_private *dev_priv);void intel_encoder_destroy (struct drm_encoder *encoder);struct drm_display_mode *intel_encoder_current_mode (struct intel_encoder *encoder); +struct intel_digital_port * +intel_connector_primary_digital_port (struct intel_connector *connector);bool intel_port_is_combophy (struct drm_i915_private *dev_priv,enum port port);bool intel_port_is_tc (struct drm_i915_private *dev_priv,enum port port); enum tc_port intel_port_to_tc(struct drm_i915_private *dev_priv,
drivers/gpu/drm/i915/intel_hdmi.c +7 -0
@@ -3092,6 +3092,13 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port,else intel_connector->get_hw_state = intel_connector_get_hw_state; +if (intel_port_is_tc (dev_priv, intel_encoder->port)) { + intel_connector->update_prepare = + intel_ddi_connector_update_prepare; + intel_connector->update_complete = + intel_ddi_connector_update_complete; + } +intel_hdmi_add_properties (intel_hdmi, connector);intel_connector_attach_encoder (intel_connector, intel_encoder);
drivers/gpu/drm/i915/intel_tc.c +69 -24
166 lines not on this page · raw message
drivers/gpu/drm/i915/intel_tc.h +3 -0
@@ -14,6 +14,9 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port);void intel_tc_port_sanitize (struct intel_digital_port *dig_port);void intel_tc_port_lock (struct intel_digital_port *dig_port);void intel_tc_port_unlock (struct intel_digital_port *dig_port); +void intel_tc_port_get_link (struct intel_digital_port *dig_port, +int required_lanes); +void intel_tc_port_put_link (struct intel_digital_port *dig_port);void intel_tc_port_init (struct intel_digital_port *dig_port,bool is_legacy);
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 20/23] drm/i915: Keep the TypeC port mode fixed when the port is active
Quoted 66 lines · Imre Deak
The TypeC port mode needs to stay fixed whenever the port is active. Do that by introducing a
tc_link_refcountto account for active ports, avoiding changing the port mode if a reference is held.During the modeset commit phase we also have to reset the port mode and update the active PLL reflecting the new port mode. We can do this only once the port and its old PLL has been already disabled. Add the new connector_update_prepare/complete hooks that are called around the whole enabling sequence. The TypeC specific hooks of these will reset the port mode, update the active PLL if the port will be active and ensure that the port mode will stay fixed for the duration of the whole enabling sequence by holding a
tc_link_refcount.During the port enabling, the pre_pll_enable/post_pll_disable hooks will take/release a
tc_link_refcountto ensure the port mode stays fixed while the port is active.Changing the port mode should also be avoided during connector detection and AUX transfers if the port is active, we'll do that by checking the port's
tc_link_refcount.When resetting the port mode we also have to take into account the maximum lanes provided by the FIA. It's guaranteed to be 4 in TBT-alt and legacy modes, but there may be less lanes available in DP-alt mode, in which case we have to fall back to TBT-alt mode.
While at it also update icl_tc_phy_connect()'s code comment, reflecting the current way of switching the port mode.
Cc Ville Syrjälä <[email protected]>Cc Daniel Vetter <[email protected]>Cc Maarten Lankhorst <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_ddi.c | 46 +++++++++++-- drivers/gpu/drm/i915/intel_ddi.h | 7 ++ drivers/gpu/drm/i915/intel_display.c | 90 +++++++++++++++++++++++++- drivers/gpu/drm/i915/intel_dp.c | 7 ++ drivers/gpu/drm/i915/intel_dp_mst.c | 6 ++ drivers/gpu/drm/i915/intel_dpll_mgr.c | 28 +++++++- drivers/gpu/drm/i915/intel_dpll_mgr.h | 3 + drivers/gpu/drm/i915/intel_drv.h | 9 +++ drivers/gpu/drm/i915/intel_hdmi.c | 7 ++ drivers/gpu/drm/i915/intel_tc.c | 93 ++++++++++++++++++++------- drivers/gpu/drm/i915/intel_tc.h | 3 + 11 files changed, 269 insertions(+), 30 deletions(-)drivers/gpu/drm/i915/intel_ddi.c +11
-0@@ -3610,6 +3610,38 @@ static void intel_ddi_set_fia_lane_count(struct intel_encoder *encoder,I915_WRITE (PORT_TX_DFLEXDPMLE1 , val); } +void +intel_ddi_connector_update_prepare (struct intel_atomic_state *state, +struct intel_connector *connector) +{ +struct drm_connector_state *conn_state = +drm_atomic_get_new_connector_state (&state->base, + &connector->base); +struct intel_crtc *crtc = conn_state->crtc ? +to_intel_crtc (conn_state->crtc) :NULL ; +struct intel_crtc_state *crtc_state = + crtc ?intel_atomic_get_new_crtc_state (state, crtc) :NULL ;
drivers/gpu/drm/i915/intel_ddi.c static void intel_ddi_set_fia_lane_count(struct intel_encoder *encoder, · line 3633
Quoted 10 lines
drivers/gpu/drm/i915/intel_ddi.c +10
-0+struct intel_digital_port *primary_port = +intel_connector_primary_digital_port (connector); +int required_lanes = crtc_state ? crtc_state->lane_count :1 ; + +WARN_ON (crtc && crtc->active); + +intel_tc_port_get_link (primary_port, required_lanes); +if (crtc_state && crtc_state->base.active) +intel_update_active_dpll (state, crtc, &primary_port->base); +}
Having this as a connector hook feels a bit strange. I guess moving it to encoder level would feel more in line with the rest of the hooks, and would avoid having that intel_connector_primary_digital_port() thing because then the mst code could just pass in the right thing itself. Hmm. Or maybe that wouldn't actually work because of intel_connector->encoder being wonky on MST :(
Although if we just put the hooks on the main encoder and not on the MST ones it could maybe work. Would still need intel_connector_primary_digital_port() to dig out the encoder though.
Not sure.
Quoted 82 lines
drivers/gpu/drm/i915/intel_ddi.c +21
-4+ +void +intel_ddi_connector_update_complete (struct intel_atomic_state *state, +struct intel_connector *connector) +{ +struct intel_digital_port *primary_port = +intel_connector_primary_digital_port (connector); + +intel_tc_port_put_link (primary_port); +} + static void intel_ddi_pre_pll_enable(struct intel_encoder *encoder, const struct intel_crtc_state *crtc_state,@@ -3617,10 +3649,13 @@ intel_ddi_pre_pll_enable(struct intel_encoder *encoder, {struct drm_i915_private *dev_priv =to_i915 (encoder->base.dev);struct intel_digital_port *dig_port =enc_to_dig_port (&encoder->base); +bool is_tc_port =intel_port_is_tc (dev_priv, encoder->port);enum port port = encoder->port; -if (intel_crtc_has_dp_encoder (crtc_state) || -intel_port_is_tc (dev_priv, encoder->port)) +if (is_tc_port) +intel_tc_port_get_link (dig_port, crtc_state->lane_count); + +if (intel_crtc_has_dp_encoder (crtc_state) || is_tc_port)intel_display_power_get (dev_priv,intel_ddi_main_link_aux_domain (dig_port));@@ -3645,11 +3680,14 @@ intel_ddi_post_pll_disable(struct intel_encoder *encoder, {struct drm_i915_private *dev_priv =to_i915 (encoder->base.dev);struct intel_digital_port *dig_port =enc_to_dig_port (&encoder->base); +bool is_tc_port =intel_port_is_tc (dev_priv, encoder->port); -if (intel_crtc_has_dp_encoder (crtc_state) || -intel_port_is_tc (dev_priv, encoder->port)) +if (intel_crtc_has_dp_encoder (crtc_state) || is_tc_port)intel_display_power_put_unchecked (dev_priv,intel_ddi_main_link_aux_domain (dig_port)); + +if (is_tc_port) +intel_tc_port_put_link (dig_port); }void intel_ddi_prepare_link_retrain (struct intel_dp *intel_dp)drivers/gpu/drm/i915/intel_ddi.h +7
-0@@ -12,6 +12,7 @@struct drm_connector_state ;struct drm_i915_private ; +struct intel_atomic_state ;struct intel_connector ;struct intel_crtc ;struct intel_crtc_state ;@@ -35,6 +36,12 @@ void intel_ddi_prepare_link_retrain(struct intel_dp *intel_dp);bool intel_ddi_connector_get_hw_state (struct intel_connector *intel_connector);void intel_ddi_get_config (struct intel_encoder *encoder,struct intel_crtc_state *pipe_config); +void +intel_ddi_connector_update_prepare (struct intel_atomic_state *state, +struct intel_connector *connector); +void +intel_ddi_connector_update_complete (struct intel_atomic_state *state, +struct intel_connector *connector);void intel_ddi_set_vc_payload_alloc (const struct intel_crtc_state *crtc_state,bool state); void intel_ddi_compute_min_voltage_level(struct drm_i915_private *dev_priv,drivers/gpu/drm/i915/intel_display.c +2
-0@@ -520,6 +520,20 @@ needs_modeset(const struct drm_crtc_state *state)return drm_atomic_crtc_needs_modeset (state); } +static bool +intel_connector_needs_modeset(struct intel_atomic_state *state,
drivers/gpu/drm/i915/intel_display.c needs_modeset(const struct drm_crtc_state *state) · line 534
Quoted 10 lines
drivers/gpu/drm/i915/intel_display.c +10
-0+ const struct drm_connector_state *old_conn_state, + const struct drm_connector_state *new_conn_state) +{ + if (new_conn_state->crtc != old_conn_state->crtc || + (new_conn_state->crtc && + needs_modeset(drm_atomic_get_new_crtc_state(&state->base, + new_conn_state->crtc)))) + return true; + +return false;
Pointless if statement. Or is there more coming here?
Quoted 458 lines
drivers/gpu/drm/i915/intel_display.c +77
-1+} +/* * Platform specific helpers to calculate the port PLL loopback- (clock.m), * and post-divider (clock.p) values, pre- (clock.vco) and post-divided fast @@ -6032,6 +6046,52 @@ static void intel_crtc_disable_planes(struct intel_atomic_state *state,intel_frontbuffer_flip (dev_priv, fb_bits); } +static void intel_connectors_update_prepare (struct intel_atomic_state *state) +{ +struct drm_connector_state *old_conn_state; +struct drm_connector_state *new_conn_state; +struct drm_connector *conn; +int i; + +for_each_oldnew_connector_in_state (&state->base, conn, + old_conn_state, new_conn_state, i) { +struct intel_connector *connector =to_intel_connector (conn); + +if (!connector->update_prepare) +continue ; + +if (!intel_connector_needs_modeset (state, + old_conn_state, + new_conn_state)) +continue ; + + connector->update_prepare (state, connector); + } +} + +static void intel_connectors_update_complete (struct intel_atomic_state *state) +{ +struct drm_connector_state *old_conn_state; +struct drm_connector_state *new_conn_state; +struct drm_connector *conn; +int i; + +for_each_oldnew_connector_in_state (&state->base, conn, + old_conn_state, new_conn_state, i) { +struct intel_connector *connector =to_intel_connector (conn); + +if (!connector->update_complete) +continue ; + +if (!intel_connector_needs_modeset (state, + old_conn_state, + new_conn_state)) +continue ; + + connector->update_complete (state, connector); + } +} +static void intel_encoders_pre_pll_enable (struct drm_crtc *crtc,struct intel_crtc_state *crtc_state,struct drm_atomic_state *old_state)@@ -6556,6 +6616,28 @@ static void i9xx_pfit_enable(const struct intel_crtc_state *crtc_state)I915_WRITE (BCLRPAT (crtc->pipe),0 ); } +/* +* intel_connector_primary_digital_port - get the primary port for a connector +* @connector: connector for which to return the port +* +* Returns the primary digital port for a DP MST, the single digital port for +* DP SST and HDMI and NULL for all other connector types. +*/ +struct intel_digital_port * +intel_connector_primary_digital_port (struct intel_connector *connector) +{ +struct intel_encoder *encoder; + +if (connector->mst_port) +return dp_to_dig_port (connector->mst_port); + + encoder =intel_attached_encoder (&connector->base); +if (WARN_ON (!encoder)) +return NULL ; + +return enc_to_dig_port (&encoder->base); +} +bool intel_port_is_combophy (struct drm_i915_private *dev_priv,enum port port) {if (port ==PORT_NONE )@@ -13805,14 +13887,20 @@ static void intel_atomic_commit_tail(struct drm_atomic_state *state) } } +if (intel_state->modeset) +intel_connectors_update_prepare (intel_state); +/* Now enable the clocks, plane, pipe, and connectors that we set up. */ dev_priv->display.update_crtcs (state); -if (intel_state->modeset) +if (intel_state->modeset) { +intel_connectors_update_complete (intel_state); +intel_set_cdclk_post_plane_update (dev_priv, &intel_state->cdclk.actual, &dev_priv->cdclk.actual, intel_state->cdclk.pipe); + }/* FIXME: We should call drm_atomic_helper_commit_hw_done() here * already, but still need the state for the delayed optimization. To drivers/gpu/drm/i915/intel_dp.c +7
-0@@ -7195,6 +7195,13 @@ intel_dp_init_connector(struct intel_digital_port *intel_dig_port,else intel_connector->get_hw_state = intel_connector_get_hw_state; +if (intel_port_is_tc (dev_priv, intel_encoder->port)) { + intel_connector->update_prepare = + intel_ddi_connector_update_prepare; + intel_connector->update_complete = + intel_ddi_connector_update_complete; + } +/* init MST on ports that can support it */ if (HAS_DP_MST(dev_priv) && !intel_dp_is_edp(intel_dp) && (port == PORT_B || port == PORT_C ||drivers/gpu/drm/i915/intel_dp_mst.c +6
-0@@ -505,6 +505,12 @@ static struct drm_connector *intel_dp_add_mst_connector(struct drm_dp_mst_topoloif (!intel_connector)return NULL ; +if (intel_port_is_tc (dev_priv, intel_dig_port->base.port)) { + intel_connector->update_prepare = + intel_ddi_connector_update_prepare; + intel_connector->update_complete = + intel_ddi_connector_update_complete; + } intel_connector->get_hw_state = intel_dp_mst_get_hw_state; intel_connector->mst_port = intel_dp; intel_connector->port = port;drivers/gpu/drm/i915/intel_dpll_mgr.c +27
-1@@ -1939,7 +1939,9 @@ struct intel_dpll_mgr { struct intel_encoder *encoder);void (*put_dplls)(struct intel_atomic_state *state,struct intel_crtc *crtc); - +void (*update_active_dpll)(struct intel_atomic_state *state, +struct intel_crtc *crtc, +struct intel_encoder *encoder);void (*dump_hw_state)(struct drm_i915_private *dev_priv,const struct intel_dpll_hw_state *hw_state); };@@ -3401,6 +3403,7 @@ static const struct intel_dpll_mgr icl_pll_mgr = { .dpll_info = icl_plls, .get_dplls = icl_get_dplls, .put_dplls = icl_put_dplls, + .update_active_dpll = icl_update_active_dpll, .dump_hw_state = icl_dump_hw_state, };@@ -3525,6 +3528,29 @@ void intel_release_shared_dplls(struct intel_atomic_state *state, dpll_mgr->put_dplls (state, crtc); } +/** +* intel_update_active_dpll - update the active DPLL for a CRTC/encoder +* @state: atomic state +* @crtc: the CRTC for which to update the active DPLL +* @encoder: encoder determining the type of port DPLL +* +* Update the active DPLL for the given @crtc/@encoder in @crtc's atomic state, +* from the port DPLLs reserved previously by intel_reserve_shared_dplls(). The +* DPLL selected will be based on the current mode of the encoder's port. +*/ +void intel_update_active_dpll (struct intel_atomic_state *state, +struct intel_crtc *crtc, +struct intel_encoder *encoder) +{ +struct drm_i915_private *dev_priv =to_i915 (encoder->base.dev); +const struct intel_dpll_mgr *dpll_mgr = dev_priv->dpll_mgr; + +if (WARN_ON (!dpll_mgr)) +return ; + + dpll_mgr->update_active_dpll (state, crtc, encoder); +} +/** * intel_shared_dpll_dump_hw_state - write hw_state to dmesg * @dev_priv: i915 drm device drivers/gpu/drm/i915/intel_dpll_mgr.h +3
-0@@ -346,6 +346,9 @@ void intel_release_shared_dplls(struct intel_atomic_state *state, struct intel_crtc *crtc);void icl_set_active_port_dpll (struct intel_crtc_state *crtc_state,enum icl_port_dpll_id port_dpll_id); +void intel_update_active_dpll (struct intel_atomic_state *state, +struct intel_crtc *crtc, +struct intel_encoder *encoder);void intel_prepare_shared_dpll (const struct intel_crtc_state *crtc_state);void intel_enable_shared_dpll (const struct intel_crtc_state *crtc_state);void intel_disable_shared_dpll (const struct intel_crtc_state *crtc_state);drivers/gpu/drm/i915/intel_drv.h +9
-0@@ -375,6 +375,11 @@ struct intel_connector {* and active (i.e. dpms ON state). */ bool (*get_hw_state)(struct intel_connector *); +void (*update_prepare)(struct intel_atomic_state *state, +struct intel_connector *connector); +void (*update_complete)(struct intel_atomic_state *state, +struct intel_connector *connector); +/* Panel info for eDP and LVDS */ struct intel_panel panel;@@ -1234,6 +1239,8 @@ struct intel_digital_port {enum aux_ch aux_ch;enum intel_display_power_domain ddi_io_power_domain;struct mutex tc_lock; +intel_wakeref_t tc_lock_wakeref; +int tc_link_refcount; bool tc_legacy_port:1;enum tc_port_mode tc_mode;@@ -1485,6 +1492,8 @@ void intel_pps_unlock_regs_wa(struct drm_i915_private *dev_priv);void intel_encoder_destroy (struct drm_encoder *encoder);struct drm_display_mode *intel_encoder_current_mode (struct intel_encoder *encoder); +struct intel_digital_port * +intel_connector_primary_digital_port (struct intel_connector *connector);bool intel_port_is_combophy (struct drm_i915_private *dev_priv,enum port port);bool intel_port_is_tc (struct drm_i915_private *dev_priv,enum port port); enum tc_port intel_port_to_tc(struct drm_i915_private *dev_priv,drivers/gpu/drm/i915/intel_hdmi.c +7
-0@@ -3092,6 +3092,13 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port,else intel_connector->get_hw_state = intel_connector_get_hw_state; +if (intel_port_is_tc (dev_priv, intel_encoder->port)) { + intel_connector->update_prepare = + intel_ddi_connector_update_prepare; + intel_connector->update_complete = + intel_ddi_connector_update_complete; + } +intel_hdmi_add_properties (intel_hdmi, connector);intel_connector_attach_encoder (intel_connector, intel_encoder);drivers/gpu/drm/i915/intel_tc.c +69
-24@@ -188,21 +188,13 @@ static bool icl_tc_phy_is_in_safe_mode(struct intel_digital_port *dig_port)* display, USB, etc. As a result, handshaking through FIA is required around * connect and disconnect to cleanly transfer ownership with the controller and * set the type-C power state. -* -* We could opt to only do the connect flow when we actually try to use the AUX -* channels or do a modeset, then immediately run the disconnect flow after -* usage, but there are some implications on this for a dynamic environment: -* things may go away or change behind our backs. So for now our driver is -* always trying to acquire ownership of the controller as soon as it gets an -* interrupt (or polls state and sees a port is connected) and only gives it -* back when it sees a disconnect. Implementation of a more fine-grained model -* will require a lot of coordination with user space and thorough testing for -* the extra possible cases. */ -static void icl_tc_phy_connect (struct intel_digital_port *dig_port) +static void icl_tc_phy_connect (struct intel_digital_port *dig_port, +int required_lanes) {struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +int max_lanes;if (!icl_tc_phy_status_complete (dig_port)) { DRM_DEBUG_KMS("Port %s: PHY not ready\n",@@ -214,8 +206,9 @@ static void icl_tc_phy_connect(struct intel_digital_port *dig_port) !WARN_ON(dig_port->tc_legacy_port)) goto out_set_tbt_alt_mode; + max_lanes =intel_tc_port_fia_max_lane_count (dig_port);if (dig_port->tc_legacy_port) { -WARN_ON (intel_tc_port_fia_max_lane_count (dig_port) !=4 ); +WARN_ON (max_lanes !=4 ); dig_port->tc_mode =TC_PORT_LEGACY ;return ;@@ -231,6 +224,13 @@ static void icl_tc_phy_connect(struct intel_digital_port *dig_port) goto out_set_safe_mode; } +if (max_lanes < required_lanes) { +DRM_DEBUG_KMS ("Port %s: PHY max lanes %d < required lanes %d\n" , +tc_port_name (dev_priv, tc_port), + max_lanes, required_lanes); + goto out_set_safe_mode; + } + dig_port->tc_mode =TC_PORT_DP_ALT ;return ;@@ -317,7 +317,8 @@ intel_tc_port_get_target_mode(struct intel_digital_port *dig_port)TC_PORT_TBT_ALT ; } -static void intel_tc_port_reset_mode (struct intel_digital_port *dig_port) +static void intel_tc_port_reset_mode (struct intel_digital_port *dig_port, +int required_lanes) {struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port);@@ -326,7 +327,7 @@ static void intel_tc_port_reset_mode(struct intel_digital_port *dig_port)intel_display_power_flush_work (dev_priv);icl_tc_phy_disconnect (dig_port); -icl_tc_phy_connect (dig_port); +icl_tc_phy_connect (dig_port, required_lanes); DRM_DEBUG_KMS("Port %s: TC port mode reset (%s -> %s)\n", tc_port_name(dev_priv, tc_port),@@ -334,6 +335,14 @@ static void intel_tc_port_reset_mode(struct intel_digital_port *dig_port) tc_port_mode_name(dig_port->tc_mode)); } +static void +intel_tc_port_link_init_refcount (struct intel_digital_port *dig_port, +int refcount) +{ +WARN_ON (dig_port->tc_link_refcount); + dig_port->tc_link_refcount = refcount; +} +void intel_tc_port_sanitize (struct intel_digital_port *dig_port) {struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);@@ -354,11 +363,13 @@ void intel_tc_port_sanitize(struct intel_digital_port *dig_port)DRM_DEBUG_DRIVER ("Port %s: PHY disconnected with %d active link(s)\n" ,tc_port_name (dev_priv, tc_port), active_links); +intel_tc_port_link_init_refcount (dig_port, active_links); + goto out; }if (dig_port->tc_legacy_port) -icl_tc_phy_connect (dig_port); +icl_tc_phy_connect (dig_port,1 ); out: DRM_DEBUG_DRIVER("Port %s: sanitize mode (%s)\n",@@ -388,27 +399,60 @@ bool intel_tc_port_connected(struct intel_digital_port *dig_port) {bool is_connected; -mutex_lock (&dig_port->tc_lock); - -if (intel_tc_port_needs_reset (dig_port)) -intel_tc_port_reset_mode (dig_port); - +intel_tc_port_lock (dig_port); is_connected =tc_port_live_status_mask (dig_port) &BIT (dig_port->tc_mode); - -mutex_unlock (&dig_port->tc_lock); +intel_tc_port_unlock (dig_port);return is_connected; } -void intel_tc_port_lock (struct intel_digital_port *dig_port) +static void __intel_tc_port_lock (struct intel_digital_port *dig_port, +int required_lanes) { +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +intel_wakeref_t wakeref; + + wakeref =intel_display_power_get (dev_priv,POWER_DOMAIN_DISPLAY_CORE ); +mutex_lock (&dig_port->tc_lock); -/* TODO: reset the TypeC port mode if needed */ + +if (!dig_port->tc_link_refcount && +intel_tc_port_needs_reset (dig_port)) +intel_tc_port_reset_mode (dig_port, required_lanes); + +WARN_ON (dig_port->tc_lock_wakeref); + dig_port->tc_lock_wakeref = wakeref; +} + +void intel_tc_port_lock (struct intel_digital_port *dig_port) +{ +__intel_tc_port_lock (dig_port,1 ); }void intel_tc_port_unlock (struct intel_digital_port *dig_port) { +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +intel_wakeref_t wakeref =fetch_and_zero (&dig_port->tc_lock_wakeref); + +mutex_unlock (&dig_port->tc_lock); + +intel_display_power_put_async (dev_priv,POWER_DOMAIN_DISPLAY_CORE , + wakeref); +} + +void intel_tc_port_get_link (struct intel_digital_port *dig_port, +int required_lanes) +{ +__intel_tc_port_lock (dig_port, required_lanes); + dig_port->tc_link_refcount++; +intel_tc_port_unlock (dig_port); +} + +void intel_tc_port_put_link (struct intel_digital_port *dig_port) +{ +mutex_lock (&dig_port->tc_lock); + dig_port->tc_link_refcount--;mutex_unlock (&dig_port->tc_lock); }@@ -417,4 +461,5 @@ intel_tc_port_init(struct intel_digital_port *dig_port, bool is_legacy) {mutex_init (&dig_port->tc_lock); dig_port->tc_legacy_port = is_legacy; + dig_port->tc_link_refcount =0 ; }drivers/gpu/drm/i915/intel_tc.h +3
-0@@ -14,6 +14,9 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port);void intel_tc_port_sanitize (struct intel_digital_port *dig_port);void intel_tc_port_lock (struct intel_digital_port *dig_port);void intel_tc_port_unlock (struct intel_digital_port *dig_port); +void intel_tc_port_get_link (struct intel_digital_port *dig_port, +int required_lanes); +void intel_tc_port_put_link (struct intel_digital_port *dig_port);void intel_tc_port_init (struct intel_digital_port *dig_port,bool is_legacy);Signature · 1 line
2.17.1
Signature · 6 lines
Ville Syrjälä Intel _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 20/23] drm/i915: Keep the TypeC port mode fixed when the port is active
Quoted 76 lines · Ville Syrjälä
Quoted 75 lines · Imre Deak
The TypeC port mode needs to stay fixed whenever the port is active. Do that by introducing a
tc_link_refcountto account for active ports, avoiding changing the port mode if a reference is held.During the modeset commit phase we also have to reset the port mode and update the active PLL reflecting the new port mode. We can do this only once the port and its old PLL has been already disabled. Add the new connector_update_prepare/complete hooks that are called around the whole enabling sequence. The TypeC specific hooks of these will reset the port mode, update the active PLL if the port will be active and ensure that the port mode will stay fixed for the duration of the whole enabling sequence by holding a
tc_link_refcount.During the port enabling, the pre_pll_enable/post_pll_disable hooks will take/release a
tc_link_refcountto ensure the port mode stays fixed while the port is active.Changing the port mode should also be avoided during connector detection and AUX transfers if the port is active, we'll do that by checking the port's
tc_link_refcount.When resetting the port mode we also have to take into account the maximum lanes provided by the FIA. It's guaranteed to be 4 in TBT-alt and legacy modes, but there may be less lanes available in DP-alt mode, in which case we have to fall back to TBT-alt mode.
While at it also update icl_tc_phy_connect()'s code comment, reflecting the current way of switching the port mode.
Cc Ville Syrjälä <[email protected]>Cc Daniel Vetter <[email protected]>Cc Maarten Lankhorst <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_ddi.c | 46 +++++++++++-- drivers/gpu/drm/i915/intel_ddi.h | 7 ++ drivers/gpu/drm/i915/intel_display.c | 90 +++++++++++++++++++++++++- drivers/gpu/drm/i915/intel_dp.c | 7 ++ drivers/gpu/drm/i915/intel_dp_mst.c | 6 ++ drivers/gpu/drm/i915/intel_dpll_mgr.c | 28 +++++++- drivers/gpu/drm/i915/intel_dpll_mgr.h | 3 + drivers/gpu/drm/i915/intel_drv.h | 9 +++ drivers/gpu/drm/i915/intel_hdmi.c | 7 ++ drivers/gpu/drm/i915/intel_tc.c | 93 ++++++++++++++++++++------- drivers/gpu/drm/i915/intel_tc.h | 3 + 11 files changed, 269 insertions(+), 30 deletions(-)drivers/gpu/drm/i915/intel_ddi.c +20
-0@@ -3610,6 +3610,38 @@ static void intel_ddi_set_fia_lane_count(struct intel_encoder *encoder,I915_WRITE (PORT_TX_DFLEXDPMLE1 , val); } +void +intel_ddi_connector_update_prepare (struct intel_atomic_state *state, +struct intel_connector *connector) +{ +struct drm_connector_state *conn_state = +drm_atomic_get_new_connector_state (&state->base, + &connector->base); +struct intel_crtc *crtc = conn_state->crtc ? +to_intel_crtc (conn_state->crtc) :NULL ; +struct intel_crtc_state *crtc_state = + crtc ?intel_atomic_get_new_crtc_state (state, crtc) :NULL ; +struct intel_digital_port *primary_port = +intel_connector_primary_digital_port (connector); +int required_lanes = crtc_state ? crtc_state->lane_count :1 ; + +WARN_ON (crtc && crtc->active); + +intel_tc_port_get_link (primary_port, required_lanes); +if (crtc_state && crtc_state->base.active) +intel_update_active_dpll (state, crtc, &primary_port->base);
Quoted 8 lines
drivers/gpu/drm/i915/intel_ddi.c static void intel_ddi_set_fia_lane_count(struct intel_encoder *encoder, · line 3633
Quoted 1 line
drivers/gpu/drm/i915/intel_ddi.c +1
-0+}Having this as a connector hook feels a bit strange. I guess moving it to encoder level would feel more in line with the rest of the hooks, and would avoid having that
intel_connector_primary_digital_port()thing because then the mst code could just pass in the right thing itself. Hmm. Or maybe that wouldn't actually work because ofintel_connector->encoderbeing wonky on MST :(
Yep, it took a while to wrap my mind around the tracking of the MST connector->encoder mapping. The only certainty here is that we have a fixed encoder for all non-MST connectors and the primary encoder for MST connectors. Things would simplify a lot even by keeping the above hooks connector specific, but adding separate MST versions of them to deal with the connector->primary encoder mapping, which would remove the need for intel_connector_primary_digital_port().
I see now though, that it makes more sense to add these hooks to the encoder, which also simplifies things a lot, so I chose that instead.
Quoted 4 lines
Although if we just put the hooks on the main encoder and not on the MST ones it could maybe work. Would still need
intel_connector_primary_digital_port()to dig out the encoder though.
Yep, this turned out to be simplifying things a lot (by adding a new intel_connector_primary_encoder() helper instead):
https://github.com/ideak/linux/commit/49dc011132
This way it's enough to assign the hooks to the common DDI encoder, instead of assigning them to each type of connectors used with a DDI encoder.
Will post a v2 patchset with all the comments addressed after some testing, an updated version is at:
https://github.com/ideak/linux/commits/typec-mode-switch
Quoted 83 lines
Not sure.
Quoted 80 lines
drivers/gpu/drm/i915/intel_ddi.c +21
-4+ +void +intel_ddi_connector_update_complete (struct intel_atomic_state *state, +struct intel_connector *connector) +{ +struct intel_digital_port *primary_port = +intel_connector_primary_digital_port (connector); + +intel_tc_port_put_link (primary_port); +} + static void intel_ddi_pre_pll_enable(struct intel_encoder *encoder, const struct intel_crtc_state *crtc_state,@@ -3617,10 +3649,13 @@ intel_ddi_pre_pll_enable(struct intel_encoder *encoder, {struct drm_i915_private *dev_priv =to_i915 (encoder->base.dev);struct intel_digital_port *dig_port =enc_to_dig_port (&encoder->base); +bool is_tc_port =intel_port_is_tc (dev_priv, encoder->port);enum port port = encoder->port; -if (intel_crtc_has_dp_encoder (crtc_state) || -intel_port_is_tc (dev_priv, encoder->port)) +if (is_tc_port) +intel_tc_port_get_link (dig_port, crtc_state->lane_count); + +if (intel_crtc_has_dp_encoder (crtc_state) || is_tc_port)intel_display_power_get (dev_priv,intel_ddi_main_link_aux_domain (dig_port));@@ -3645,11 +3680,14 @@ intel_ddi_post_pll_disable(struct intel_encoder *encoder, {struct drm_i915_private *dev_priv =to_i915 (encoder->base.dev);struct intel_digital_port *dig_port =enc_to_dig_port (&encoder->base); +bool is_tc_port =intel_port_is_tc (dev_priv, encoder->port); -if (intel_crtc_has_dp_encoder (crtc_state) || -intel_port_is_tc (dev_priv, encoder->port)) +if (intel_crtc_has_dp_encoder (crtc_state) || is_tc_port)intel_display_power_put_unchecked (dev_priv,intel_ddi_main_link_aux_domain (dig_port)); + +if (is_tc_port) +intel_tc_port_put_link (dig_port); }void intel_ddi_prepare_link_retrain (struct intel_dp *intel_dp)drivers/gpu/drm/i915/intel_ddi.h +7
-0@@ -12,6 +12,7 @@struct drm_connector_state ;struct drm_i915_private ; +struct intel_atomic_state ;struct intel_connector ;struct intel_crtc ;struct intel_crtc_state ;@@ -35,6 +36,12 @@ void intel_ddi_prepare_link_retrain(struct intel_dp *intel_dp);bool intel_ddi_connector_get_hw_state (struct intel_connector *intel_connector);void intel_ddi_get_config (struct intel_encoder *encoder,struct intel_crtc_state *pipe_config); +void +intel_ddi_connector_update_prepare (struct intel_atomic_state *state, +struct intel_connector *connector); +void +intel_ddi_connector_update_complete (struct intel_atomic_state *state, +struct intel_connector *connector);void intel_ddi_set_vc_payload_alloc (const struct intel_crtc_state *crtc_state,bool state); void intel_ddi_compute_min_voltage_level(struct drm_i915_private *dev_priv,drivers/gpu/drm/i915/intel_display.c +0
-0@@ -520,6 +520,20 @@ needs_modeset(const struct drm_crtc_state *state)return drm_atomic_crtc_needs_modeset (state); }
Quoted 14 lines
drivers/gpu/drm/i915/intel_display.c needs_modeset(const struct drm_crtc_state *state) · line 534
Quoted 12 lines
drivers/gpu/drm/i915/intel_display.c +12
-0+static bool +intel_connector_needs_modeset (struct intel_atomic_state *state, +const struct drm_connector_state *old_conn_state, +const struct drm_connector_state *new_conn_state) +{ +if (new_conn_state->crtc != old_conn_state->crtc || + (new_conn_state->crtc && +needs_modeset (drm_atomic_get_new_crtc_state (&state->base, + new_conn_state->crtc)))) +return true; + +return false;Pointless if statement. Or is there more coming here?
Nope, it can be simplified.
Quoted 455 lines
Quoted 455 lines
drivers/gpu/drm/i915/intel_display.c +77
-1+} +/* * Platform specific helpers to calculate the port PLL loopback- (clock.m), * and post-divider (clock.p) values, pre- (clock.vco) and post-divided fast @@ -6032,6 +6046,52 @@ static void intel_crtc_disable_planes(struct intel_atomic_state *state,intel_frontbuffer_flip (dev_priv, fb_bits); } +static void intel_connectors_update_prepare (struct intel_atomic_state *state) +{ +struct drm_connector_state *old_conn_state; +struct drm_connector_state *new_conn_state; +struct drm_connector *conn; +int i; + +for_each_oldnew_connector_in_state (&state->base, conn, + old_conn_state, new_conn_state, i) { +struct intel_connector *connector =to_intel_connector (conn); + +if (!connector->update_prepare) +continue ; + +if (!intel_connector_needs_modeset (state, + old_conn_state, + new_conn_state)) +continue ; + + connector->update_prepare (state, connector); + } +} + +static void intel_connectors_update_complete (struct intel_atomic_state *state) +{ +struct drm_connector_state *old_conn_state; +struct drm_connector_state *new_conn_state; +struct drm_connector *conn; +int i; + +for_each_oldnew_connector_in_state (&state->base, conn, + old_conn_state, new_conn_state, i) { +struct intel_connector *connector =to_intel_connector (conn); + +if (!connector->update_complete) +continue ; + +if (!intel_connector_needs_modeset (state, + old_conn_state, + new_conn_state)) +continue ; + + connector->update_complete (state, connector); + } +} +static void intel_encoders_pre_pll_enable (struct drm_crtc *crtc,struct intel_crtc_state *crtc_state,struct drm_atomic_state *old_state)@@ -6556,6 +6616,28 @@ static void i9xx_pfit_enable(const struct intel_crtc_state *crtc_state)I915_WRITE (BCLRPAT (crtc->pipe),0 ); } +/* +* intel_connector_primary_digital_port - get the primary port for a connector +* @connector: connector for which to return the port +* +* Returns the primary digital port for a DP MST, the single digital port for +* DP SST and HDMI and NULL for all other connector types. +*/ +struct intel_digital_port * +intel_connector_primary_digital_port (struct intel_connector *connector) +{ +struct intel_encoder *encoder; + +if (connector->mst_port) +return dp_to_dig_port (connector->mst_port); + + encoder =intel_attached_encoder (&connector->base); +if (WARN_ON (!encoder)) +return NULL ; + +return enc_to_dig_port (&encoder->base); +} +bool intel_port_is_combophy (struct drm_i915_private *dev_priv,enum port port) {if (port ==PORT_NONE )@@ -13805,14 +13887,20 @@ static void intel_atomic_commit_tail(struct drm_atomic_state *state) } } +if (intel_state->modeset) +intel_connectors_update_prepare (intel_state); +/* Now enable the clocks, plane, pipe, and connectors that we set up. */ dev_priv->display.update_crtcs (state); -if (intel_state->modeset) +if (intel_state->modeset) { +intel_connectors_update_complete (intel_state); +intel_set_cdclk_post_plane_update (dev_priv, &intel_state->cdclk.actual, &dev_priv->cdclk.actual, intel_state->cdclk.pipe); + }/* FIXME: We should call drm_atomic_helper_commit_hw_done() here * already, but still need the state for the delayed optimization. To drivers/gpu/drm/i915/intel_dp.c +7
-0@@ -7195,6 +7195,13 @@ intel_dp_init_connector(struct intel_digital_port *intel_dig_port,else intel_connector->get_hw_state = intel_connector_get_hw_state; +if (intel_port_is_tc (dev_priv, intel_encoder->port)) { + intel_connector->update_prepare = + intel_ddi_connector_update_prepare; + intel_connector->update_complete = + intel_ddi_connector_update_complete; + } +/* init MST on ports that can support it */ if (HAS_DP_MST(dev_priv) && !intel_dp_is_edp(intel_dp) && (port == PORT_B || port == PORT_C ||drivers/gpu/drm/i915/intel_dp_mst.c +6
-0@@ -505,6 +505,12 @@ static struct drm_connector *intel_dp_add_mst_connector(struct drm_dp_mst_topoloif (!intel_connector)return NULL ; +if (intel_port_is_tc (dev_priv, intel_dig_port->base.port)) { + intel_connector->update_prepare = + intel_ddi_connector_update_prepare; + intel_connector->update_complete = + intel_ddi_connector_update_complete; + } intel_connector->get_hw_state = intel_dp_mst_get_hw_state; intel_connector->mst_port = intel_dp; intel_connector->port = port;drivers/gpu/drm/i915/intel_dpll_mgr.c +27
-1@@ -1939,7 +1939,9 @@ struct intel_dpll_mgr { struct intel_encoder *encoder);void (*put_dplls)(struct intel_atomic_state *state,struct intel_crtc *crtc); - +void (*update_active_dpll)(struct intel_atomic_state *state, +struct intel_crtc *crtc, +struct intel_encoder *encoder);void (*dump_hw_state)(struct drm_i915_private *dev_priv,const struct intel_dpll_hw_state *hw_state); };@@ -3401,6 +3403,7 @@ static const struct intel_dpll_mgr icl_pll_mgr = { .dpll_info = icl_plls, .get_dplls = icl_get_dplls, .put_dplls = icl_put_dplls, + .update_active_dpll = icl_update_active_dpll, .dump_hw_state = icl_dump_hw_state, };@@ -3525,6 +3528,29 @@ void intel_release_shared_dplls(struct intel_atomic_state *state, dpll_mgr->put_dplls (state, crtc); } +/** +* intel_update_active_dpll - update the active DPLL for a CRTC/encoder +* @state: atomic state +* @crtc: the CRTC for which to update the active DPLL +* @encoder: encoder determining the type of port DPLL +* +* Update the active DPLL for the given @crtc/@encoder in @crtc's atomic state, +* from the port DPLLs reserved previously by intel_reserve_shared_dplls(). The +* DPLL selected will be based on the current mode of the encoder's port. +*/ +void intel_update_active_dpll (struct intel_atomic_state *state, +struct intel_crtc *crtc, +struct intel_encoder *encoder) +{ +struct drm_i915_private *dev_priv =to_i915 (encoder->base.dev); +const struct intel_dpll_mgr *dpll_mgr = dev_priv->dpll_mgr; + +if (WARN_ON (!dpll_mgr)) +return ; + + dpll_mgr->update_active_dpll (state, crtc, encoder); +} +/** * intel_shared_dpll_dump_hw_state - write hw_state to dmesg * @dev_priv: i915 drm device drivers/gpu/drm/i915/intel_dpll_mgr.h +3
-0@@ -346,6 +346,9 @@ void intel_release_shared_dplls(struct intel_atomic_state *state, struct intel_crtc *crtc);void icl_set_active_port_dpll (struct intel_crtc_state *crtc_state,enum icl_port_dpll_id port_dpll_id); +void intel_update_active_dpll (struct intel_atomic_state *state, +struct intel_crtc *crtc, +struct intel_encoder *encoder);void intel_prepare_shared_dpll (const struct intel_crtc_state *crtc_state);void intel_enable_shared_dpll (const struct intel_crtc_state *crtc_state);void intel_disable_shared_dpll (const struct intel_crtc_state *crtc_state);drivers/gpu/drm/i915/intel_drv.h +9
-0@@ -375,6 +375,11 @@ struct intel_connector {* and active (i.e. dpms ON state). */ bool (*get_hw_state)(struct intel_connector *); +void (*update_prepare)(struct intel_atomic_state *state, +struct intel_connector *connector); +void (*update_complete)(struct intel_atomic_state *state, +struct intel_connector *connector); +/* Panel info for eDP and LVDS */ struct intel_panel panel;@@ -1234,6 +1239,8 @@ struct intel_digital_port {enum aux_ch aux_ch;enum intel_display_power_domain ddi_io_power_domain;struct mutex tc_lock; +intel_wakeref_t tc_lock_wakeref; +int tc_link_refcount; bool tc_legacy_port:1;enum tc_port_mode tc_mode;@@ -1485,6 +1492,8 @@ void intel_pps_unlock_regs_wa(struct drm_i915_private *dev_priv);void intel_encoder_destroy (struct drm_encoder *encoder);struct drm_display_mode *intel_encoder_current_mode (struct intel_encoder *encoder); +struct intel_digital_port * +intel_connector_primary_digital_port (struct intel_connector *connector);bool intel_port_is_combophy (struct drm_i915_private *dev_priv,enum port port);bool intel_port_is_tc (struct drm_i915_private *dev_priv,enum port port); enum tc_port intel_port_to_tc(struct drm_i915_private *dev_priv,drivers/gpu/drm/i915/intel_hdmi.c +7
-0@@ -3092,6 +3092,13 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port,else intel_connector->get_hw_state = intel_connector_get_hw_state; +if (intel_port_is_tc (dev_priv, intel_encoder->port)) { + intel_connector->update_prepare = + intel_ddi_connector_update_prepare; + intel_connector->update_complete = + intel_ddi_connector_update_complete; + } +intel_hdmi_add_properties (intel_hdmi, connector);intel_connector_attach_encoder (intel_connector, intel_encoder);drivers/gpu/drm/i915/intel_tc.c +69
-24@@ -188,21 +188,13 @@ static bool icl_tc_phy_is_in_safe_mode(struct intel_digital_port *dig_port)* display, USB, etc. As a result, handshaking through FIA is required around * connect and disconnect to cleanly transfer ownership with the controller and * set the type-C power state. -* -* We could opt to only do the connect flow when we actually try to use the AUX -* channels or do a modeset, then immediately run the disconnect flow after -* usage, but there are some implications on this for a dynamic environment: -* things may go away or change behind our backs. So for now our driver is -* always trying to acquire ownership of the controller as soon as it gets an -* interrupt (or polls state and sees a port is connected) and only gives it -* back when it sees a disconnect. Implementation of a more fine-grained model -* will require a lot of coordination with user space and thorough testing for -* the extra possible cases. */ -static void icl_tc_phy_connect (struct intel_digital_port *dig_port) +static void icl_tc_phy_connect (struct intel_digital_port *dig_port, +int required_lanes) {struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port); +int max_lanes;if (!icl_tc_phy_status_complete (dig_port)) { DRM_DEBUG_KMS("Port %s: PHY not ready\n",@@ -214,8 +206,9 @@ static void icl_tc_phy_connect(struct intel_digital_port *dig_port) !WARN_ON(dig_port->tc_legacy_port)) goto out_set_tbt_alt_mode; + max_lanes =intel_tc_port_fia_max_lane_count (dig_port);if (dig_port->tc_legacy_port) { -WARN_ON (intel_tc_port_fia_max_lane_count (dig_port) !=4 ); +WARN_ON (max_lanes !=4 ); dig_port->tc_mode =TC_PORT_LEGACY ;return ;@@ -231,6 +224,13 @@ static void icl_tc_phy_connect(struct intel_digital_port *dig_port) goto out_set_safe_mode; } +if (max_lanes < required_lanes) { +DRM_DEBUG_KMS ("Port %s: PHY max lanes %d < required lanes %d\n" , +tc_port_name (dev_priv, tc_port), + max_lanes, required_lanes); + goto out_set_safe_mode; + } + dig_port->tc_mode =TC_PORT_DP_ALT ;return ;@@ -317,7 +317,8 @@ intel_tc_port_get_target_mode(struct intel_digital_port *dig_port)TC_PORT_TBT_ALT ; } -static void intel_tc_port_reset_mode (struct intel_digital_port *dig_port) +static void intel_tc_port_reset_mode (struct intel_digital_port *dig_port, +int required_lanes) {struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);enum tc_port tc_port =intel_port_to_tc (dev_priv, dig_port->base.port);@@ -326,7 +327,7 @@ static void intel_tc_port_reset_mode(struct intel_digital_port *dig_port)intel_display_power_flush_work (dev_priv);icl_tc_phy_disconnect (dig_port); -icl_tc_phy_connect (dig_port); +icl_tc_phy_connect (dig_port, required_lanes); DRM_DEBUG_KMS("Port %s: TC port mode reset (%s -> %s)\n", tc_port_name(dev_priv, tc_port),@@ -334,6 +335,14 @@ static void intel_tc_port_reset_mode(struct intel_digital_port *dig_port) tc_port_mode_name(dig_port->tc_mode)); } +static void +intel_tc_port_link_init_refcount (struct intel_digital_port *dig_port, +int refcount) +{ +WARN_ON (dig_port->tc_link_refcount); + dig_port->tc_link_refcount = refcount; +} +void intel_tc_port_sanitize (struct intel_digital_port *dig_port) {struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev);@@ -354,11 +363,13 @@ void intel_tc_port_sanitize(struct intel_digital_port *dig_port)DRM_DEBUG_DRIVER ("Port %s: PHY disconnected with %d active link(s)\n" ,tc_port_name (dev_priv, tc_port), active_links); +intel_tc_port_link_init_refcount (dig_port, active_links); + goto out; }if (dig_port->tc_legacy_port) -icl_tc_phy_connect (dig_port); +icl_tc_phy_connect (dig_port,1 ); out: DRM_DEBUG_DRIVER("Port %s: sanitize mode (%s)\n",@@ -388,27 +399,60 @@ bool intel_tc_port_connected(struct intel_digital_port *dig_port) {bool is_connected; -mutex_lock (&dig_port->tc_lock); - -if (intel_tc_port_needs_reset (dig_port)) -intel_tc_port_reset_mode (dig_port); - +intel_tc_port_lock (dig_port); is_connected =tc_port_live_status_mask (dig_port) &BIT (dig_port->tc_mode); - -mutex_unlock (&dig_port->tc_lock); +intel_tc_port_unlock (dig_port);return is_connected; } -void intel_tc_port_lock (struct intel_digital_port *dig_port) +static void __intel_tc_port_lock (struct intel_digital_port *dig_port, +int required_lanes) { +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +intel_wakeref_t wakeref; + + wakeref =intel_display_power_get (dev_priv,POWER_DOMAIN_DISPLAY_CORE ); +mutex_lock (&dig_port->tc_lock); -/* TODO: reset the TypeC port mode if needed */ + +if (!dig_port->tc_link_refcount && +intel_tc_port_needs_reset (dig_port)) +intel_tc_port_reset_mode (dig_port, required_lanes); + +WARN_ON (dig_port->tc_lock_wakeref); + dig_port->tc_lock_wakeref = wakeref; +} + +void intel_tc_port_lock (struct intel_digital_port *dig_port) +{ +__intel_tc_port_lock (dig_port,1 ); }void intel_tc_port_unlock (struct intel_digital_port *dig_port) { +struct drm_i915_private *dev_priv =to_i915 (dig_port->base.base.dev); +intel_wakeref_t wakeref =fetch_and_zero (&dig_port->tc_lock_wakeref); + +mutex_unlock (&dig_port->tc_lock); + +intel_display_power_put_async (dev_priv,POWER_DOMAIN_DISPLAY_CORE , + wakeref); +} + +void intel_tc_port_get_link (struct intel_digital_port *dig_port, +int required_lanes) +{ +__intel_tc_port_lock (dig_port, required_lanes); + dig_port->tc_link_refcount++; +intel_tc_port_unlock (dig_port); +} + +void intel_tc_port_put_link (struct intel_digital_port *dig_port) +{ +mutex_lock (&dig_port->tc_lock); + dig_port->tc_link_refcount--;mutex_unlock (&dig_port->tc_lock); }@@ -417,4 +461,5 @@ intel_tc_port_init(struct intel_digital_port *dig_port, bool is_legacy) {mutex_init (&dig_port->tc_lock); dig_port->tc_legacy_port = is_legacy; + dig_port->tc_link_refcount =0 ; }drivers/gpu/drm/i915/intel_tc.h +3
-0@@ -14,6 +14,9 @@ int intel_tc_port_fia_max_lane_count(struct intel_digital_port *dig_port);void intel_tc_port_sanitize (struct intel_digital_port *dig_port);void intel_tc_port_lock (struct intel_digital_port *dig_port);void intel_tc_port_unlock (struct intel_digital_port *dig_port); +void intel_tc_port_get_link (struct intel_digital_port *dig_port, +int required_lanes); +void intel_tc_port_put_link (struct intel_digital_port *dig_port);
Quoted 8 lines
Quoted 4 lines
drivers/gpu/drm/i915/intel_tc.h +0
-0void intel_tc_port_init (struct intel_digital_port *dig_port,bool is_legacy);Signature · 1 line
2.17.1Signature · 2 lines
Ville Syrjälä Intel
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 21/23 drm/i915: Add state verification for the TypeC port mode
In reply to Imre DeakAdd state verification for the TypeC port mode wrt. the port's AUX power well enabling/disabling. Also check the correctness of changing the port mode:
- When enabling/disabling the AUX power well for a TypeC port we must hold already the TypeC port lock.
- When changing the TypeC port mode the port's AUX power domain must be disabled.
--- drivers/gpu/drm/i915/intel_display_power.c | 99 ++++++++++++++++++++-- drivers/gpu/drm/i915/intel_tc.c | 2 + drivers/gpu/drm/i915/intel_tc.h | 10 ++- 3 files changed, 102 insertions(+), 9 deletions(-)
drivers/gpu/drm/i915/intel_display_power.c +92 -7
@@ -16,6 +16,7 @@#include "intel_drv.h" #include "intel_hotplug.h" #include "intel_sideband.h" +#include "intel_tc.h" bool intel_display_power_well_is_enabled (struct drm_i915_private *dev_priv,enum i915_power_well_id power_well_id);
@@ -445,26 +446,110 @@ icl_combo_phy_aux_power_well_disable(struct drm_i915_private *dev_priv,#define ICL_TBT_AUX_PW_TO_CH (pw_idx) \ ((pw_idx) - ICL_PW_CTL_IDX_AUX_TBT1 + AUX_CH_C) +static enum aux_ch icl_tc_phy_aux_ch (struct drm_i915_private *dev_priv, +struct i915_power_well *power_well) +{ +int pw_idx = power_well->desc->hsw.idx; + +return power_well->desc->hsw.is_tc_tbt ?ICL_TBT_AUX_PW_TO_CH (pw_idx) : +ICL_AUX_PW_TO_CH (pw_idx); +} + +#if IS_ENABLED (CONFIG_DRM_I915_DEBUG_RUNTIME_PM ) + +static u64 async_put_domains_mask (struct i915_power_domains *power_domains); + +static int power_well_async_ref_count (struct drm_i915_private *dev_priv, +struct i915_power_well *power_well) +{ +enum intel_display_power_domain domain; +u64 async_domains =async_put_domains_mask (&dev_priv->power_domains); +int refs =0 ; + +for_each_power_domain (domain, power_well->desc->domains) + refs += !!(async_domains &BIT_ULL (domain)); + +WARN_ON (refs > power_well->count); + +return refs; +} + +static void icl_tc_port_assert_ref_held (struct drm_i915_private *dev_priv, +struct i915_power_well *power_well) +{ +enum aux_ch aux_ch =icl_tc_phy_aux_ch (dev_priv, power_well); +struct intel_digital_port *dig_port =NULL ; +struct intel_encoder *encoder; + +/* Bypass the check if all references are released asynchronously */ +if (power_well_async_ref_count (dev_priv, power_well) == + power_well->count) +return ; + + aux_ch =icl_tc_phy_aux_ch (dev_priv, power_well); + +for_each_intel_encoder (&dev_priv->drm, encoder) { +if (!intel_port_is_tc (dev_priv, encoder->port)) +continue ; + +/* We'll check the MST primary port */ +if (encoder->type ==INTEL_OUTPUT_DP_MST ) +continue ; + + dig_port =enc_to_dig_port (&encoder->base); +if (WARN_ON (!dig_port)) +continue ; + +if (dig_port->aux_ch != aux_ch) { + dig_port =NULL ; +continue ; + } + +break ; + } + +if (WARN_ON (!dig_port)) +return ; + +WARN_ON (!intel_tc_port_ref_held (dig_port)); +} + +#else + +static void icl_tc_port_assert_ref_held (struct drm_i915_private *dev_priv, +struct i915_power_well *power_well) +{ +} + +#endif +static void icl_tc_phy_aux_power_well_enable (struct drm_i915_private *dev_priv,struct i915_power_well *power_well) { -int pw_idx = power_well->desc->hsw.idx; -bool is_tbt = power_well->desc->hsw.is_tc_tbt; -enum aux_ch aux_ch; +enum aux_ch aux_ch =icl_tc_phy_aux_ch (dev_priv, power_well);u32 val; - aux_ch = is_tbt ?ICL_TBT_AUX_PW_TO_CH (pw_idx) : -ICL_AUX_PW_TO_CH (pw_idx); +icl_tc_port_assert_ref_held (dev_priv, power_well); + val =I915_READ (DP_AUX_CH_CTL (aux_ch)); val &= ~DP_AUX_CH_CTL_TBT_IO ; -if (is_tbt) +if (power_well->desc->hsw.is_tc_tbt) val |=DP_AUX_CH_CTL_TBT_IO ;I915_WRITE (DP_AUX_CH_CTL (aux_ch), val);hsw_power_well_enable (dev_priv, power_well); } +static void +icl_tc_phy_aux_power_well_disable (struct drm_i915_private *dev_priv, +struct i915_power_well *power_well) +{ +icl_tc_port_assert_ref_held (dev_priv, power_well); + +hsw_power_well_disable (dev_priv, power_well); +} +/* * We should only use the power well if we explicitly asked the hardware to * enable it, so check if it's enabled and also check if we've requested it to
@@ -3114,7 +3199,7 @@ static const struct i915_power_well_ops icl_combo_phy_aux_power_well_ops = {static const struct i915_power_well_ops icl_tc_phy_aux_power_well_ops = { .sync_hw = hsw_power_well_sync_hw, .enable = icl_tc_phy_aux_power_well_enable, - .disable = hsw_power_well_disable, + .disable = icl_tc_phy_aux_power_well_disable, .is_enabled = hsw_power_well_enabled, };
drivers/gpu/drm/i915/intel_tc.c +2 -0
@@ -325,6 +325,8 @@ static void intel_tc_port_reset_mode(struct intel_digital_port *dig_port,enum tc_port_mode old_tc_mode = dig_port->tc_mode;intel_display_power_flush_work (dev_priv); +WARN_ON (intel_display_power_is_enabled (dev_priv, +intel_aux_power_domain (dig_port)));icl_tc_phy_disconnect (dig_port);icl_tc_phy_connect (dig_port, required_lanes);
drivers/gpu/drm/i915/intel_tc.h +8 -2
@@ -2,8 +2,8 @@#define __INTEL_TC_H__#include <linux/types.h> - -struct intel_digital_port ; +#include <linux/mutex.h> +#include "intel_drv.h" void icl_tc_phy_disconnect (struct intel_digital_port *dig_port);
@@ -18,6 +18,12 @@ void intel_tc_port_get_link(struct intel_digital_port *dig_port, int required_lanes);void intel_tc_port_put_link (struct intel_digital_port *dig_port); +static inline int intel_tc_port_ref_held (struct intel_digital_port *dig_port) +{ +return mutex_is_locked (&dig_port->tc_lock) || + dig_port->tc_link_refcount; +} +void intel_tc_port_init (struct intel_digital_port *dig_port,bool is_legacy);#endif /* __INTEL_TC_H__ */
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 22/23 drm/i915: Remove unneeded disconnect in TypeC legacy port mode
In reply to Imre DeakDisconnecting the TypeC PHY when the port is in legacy mode is not necessary:
- BSpec doesn't specify a disconnect sequence for legacy mode.
- The use of the PHY is dedicated for the display in legacy mode.
- We keep the PHY always connected during runtime as well in legacy mode.
We disconnect the PHY when needed during a disabling modeset for the port, so we can also remove the disconnect call from the destroy hook.
--- drivers/gpu/drm/i915/intel_ddi.c | 21 +-------------------- drivers/gpu/drm/i915/intel_tc.c | 4 +++- drivers/gpu/drm/i915/intel_tc.h | 2 -- 3 files changed, 4 insertions(+), 23 deletions(-)
drivers/gpu/drm/i915/intel_ddi.c +1 -20
@@ -3941,31 +3941,12 @@ static int intel_ddi_compute_config(struct intel_encoder *encoder,return 0 ; } -static void intel_ddi_encoder_suspend (struct intel_encoder *encoder) -{ -struct intel_digital_port *dig_port =enc_to_dig_port (&encoder->base); - -intel_dp_encoder_suspend (encoder); - -/* -* TODO: disconnect also from USB DP alternate mode once we have a -* way to handle the modeset restore in that mode during resume -* even if the sink has disappeared while being suspended. -*/ -if (dig_port->tc_legacy_port) -icl_tc_phy_disconnect (dig_port); -} -static void intel_ddi_encoder_destroy (struct drm_encoder *encoder) {struct intel_digital_port *dig_port =enc_to_dig_port (encoder); -struct drm_i915_private *i915 =to_i915 (encoder->dev);intel_dp_encoder_flush_work (encoder); -if (intel_port_is_tc (i915, dig_port->base.port)) -icl_tc_phy_disconnect (dig_port); -drm_encoder_cleanup (encoder);kfree (dig_port); }
@@ -4254,7 +4235,7 @@ void intel_ddi_init(struct drm_i915_private *dev_priv, enum port port) intel_encoder->update_pipe = intel_ddi_update_pipe; intel_encoder->get_hw_state = intel_ddi_get_hw_state; intel_encoder->get_config = intel_ddi_get_config; - intel_encoder->suspend = intel_ddi_encoder_suspend; + intel_encoder->suspend = intel_dp_encoder_suspend; intel_encoder->get_power_domains = intel_ddi_get_power_domains; intel_encoder->type =INTEL_OUTPUT_DDI ; intel_encoder->power_domain =intel_port_to_power_domain (port);
drivers/gpu/drm/i915/intel_tc.c +3 -1
@@ -245,10 +245,12 @@ static void icl_tc_phy_connect(struct intel_digital_port *dig_port,* See the comment at the connect function. This implements the Disconnect * Flow. */ -void icl_tc_phy_disconnect (struct intel_digital_port *dig_port) +static void icl_tc_phy_disconnect (struct intel_digital_port *dig_port) {switch (dig_port->tc_mode) {case TC_PORT_LEGACY : +/* Nothing to do, we never disconnect from legacy mode */ +break ;case TC_PORT_DP_ALT :icl_tc_phy_set_safe_mode (dig_port, true); dig_port->tc_mode =TC_PORT_TBT_ALT ;
drivers/gpu/drm/i915/intel_tc.h +0 -2
@@ -5,8 +5,6 @@#include <linux/mutex.h> #include "intel_drv.h" -void icl_tc_phy_disconnect (struct intel_digital_port *dig_port); -bool intel_tc_port_connected (struct intel_digital_port *dig_port);u32 intel_tc_port_get_lane_info (struct intel_digital_port *dig_port);int intel_tc_port_fia_max_lane_count (struct intel_digital_port *dig_port);
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 22/23] drm/i915: Remove unneeded disconnect in TypeC legacy port mode
Quoted 11 lines · Imre Deak
Disconnecting the TypeC PHY when the port is in legacy mode is not necessary:
- BSpec doesn't specify a disconnect sequence for legacy mode.
- The use of the PHY is dedicated for the display in legacy mode.
- We keep the PHY always connected during runtime as well in legacy mode.We disconnect the PHY when needed during a disabling modeset for the port, so we can also remove the disconnect call from the destroy hook.
Quoted 96 lines
Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_ddi.c | 21 +-------------------- drivers/gpu/drm/i915/intel_tc.c | 4 +++- drivers/gpu/drm/i915/intel_tc.h | 2 -- 3 files changed, 4 insertions(+), 23 deletions(-)drivers/gpu/drm/i915/intel_ddi.c +0
-8@@ -3941,31 +3941,12 @@ static int intel_ddi_compute_config(structintel_encoder *encoder, return 0; } -static void intel_ddi_encoder_suspend (struct intel_encoder *encoder) -{ -struct intel_digital_port *dig_port =enc_to_dig_port (&encoder- >base); - -intel_dp_encoder_suspend (encoder); - -/* -* TODO: disconnect also from USB DP alternate mode once we have a
drivers/gpu/drm/i915/intel_ddi.c +1
-12-* way to handle the modeset restore in that mode during resume -* even if the sink has disappeared while being suspended. -*/ -if (dig_port->tc_legacy_port) -icl_tc_phy_disconnect (dig_port); -} -static void intel_ddi_encoder_destroy (struct drm_encoder *encoder) {struct intel_digital_port *dig_port =enc_to_dig_port (encoder); -struct drm_i915_private *i915 =to_i915 (encoder->dev);intel_dp_encoder_flush_work (encoder); -if (intel_port_is_tc (i915, dig_port->base.port)) -icl_tc_phy_disconnect (dig_port); -drm_encoder_cleanup (encoder);kfree (dig_port); }@@ -4254,7 +4235,7 @@ void intel_ddi_init(struct drm_i915_private *dev_priv, enum port port) intel_encoder->update_pipe = intel_ddi_update_pipe; intel_encoder->get_hw_state = intel_ddi_get_hw_state; intel_encoder->get_config = intel_ddi_get_config; - intel_encoder->suspend = intel_ddi_encoder_suspend; + intel_encoder->suspend = intel_dp_encoder_suspend; intel_encoder->get_power_domains = intel_ddi_get_power_domains; intel_encoder->type =INTEL_OUTPUT_DDI ;drivers/gpu/drm/i915/intel_ddi.c +0
-0intel_encoder->power_domain =intel_port_to_power_domain (port);drivers/gpu/drm/i915/intel_tc.c +0
-0@@ -245,10 +245,12 @@ static void icl_tc_phy_connect(structintel_digital_port *dig_port, * See the comment at the connect function. This implements theDisconnect
* Flow.
*/drivers/gpu/drm/i915/intel_tc.c +1
-1-void icl_tc_phy_disconnect (struct intel_digital_port *dig_port) +static void icl_tc_phy_disconnect(struct intel_digital_port
*dig_port)
{drivers/gpu/drm/i915/intel_tc.c +1
-0switch (dig_port->tc_mode) {case TC_PORT_LEGACY : +/* Nothing to do, we never disconnect from legacy mode */
drivers/gpu/drm/i915/intel_tc.c +1
-0+break ;case TC_PORT_DP_ALT :icl_tc_phy_set_safe_mode (dig_port, true); dig_port->tc_mode =TC_PORT_TBT_ALT ;drivers/gpu/drm/i915/intel_tc.h +0
-2@@ -5,8 +5,6 @@#include <linux/mutex.h> #include "intel_drv.h" -void icl_tc_phy_disconnect (struct intel_digital_port *dig_port); -bool intel_tc_port_connected (struct intel_digital_port *dig_port);u32 intel_tc_port_get_lane_info (struct intel_digital_port *dig_port);
Quoted 2 lines
int intel_tc_port_fia_max_lane_count(struct
intel_digital_port*dig_port);
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 23/23 drm/i915: WARN about invalid lane reversal in TBT-alt/DP-alt modes
In reply to Imre DeakLane reversal happens only in the FIA module for TBT-alt/DP-alt mode, so WARN if lane reversal is attempted at a different level. See the BSpec DDI_BUF_CTL register description.
--- drivers/gpu/drm/i915/intel_ddi.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/gpu/drm/i915/intel_ddi.c +2 -0
@@ -3591,6 +3591,8 @@ static void intel_ddi_set_fia_lane_count(struct intel_encoder *encoder,u32 val =I915_READ (PORT_TX_DFLEXDPMLE1 );bool lane_reversal = dig_port->saved_port_bits &DDI_BUF_PORT_REVERSAL ; +WARN_ON (lane_reversal && dig_port->tc_mode !=TC_PORT_LEGACY ); + val &= ~DFLEXDPMLE1_DPMLETC_MASK (tc_port);switch (pipe_config->lane_count) {case 1 :
Signature · 6 lines
2.17.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 23/23] drm/i915: WARN about invalid lane reversal in TBT-alt/DP-alt modes
Quoted 4 lines · Imre Deak
Lane reversal happens only in the FIA module for TBT-alt/DP-alt mode, so
WARN if lane reversal is attempted at a different level. See the BSpecDDI_BUF_CTLregister description.
Quoted 23 lines
Cc Manasi Navare <[email protected]>Cc José Roberto de Souza <[email protected]>Cc Rodrigo Vivi <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/intel_ddi.c | 2 ++ 1 file changed, 2 insertions(+)drivers/gpu/drm/i915/intel_ddi.c +2
-0@@ -3591,6 +3591,8 @@ static void intel_ddi_set_fia_lane_count(structintel_encoder *encoder, u32 val = I915_READ(PORT_TX_DFLEXDPMLE1);bool lane_reversal = dig_port->saved_port_bits &DDI_BUF_PORT_REVERSAL ; +WARN_ON (lane_reversal && dig_port->tc_mode !=TC_PORT_LEGACY ); + val &= ~DFLEXDPMLE1_DPMLETC_MASK (tc_port);
drivers/gpu/drm/i915/intel_ddi.c static void intel_ddi_set_fia_lane_count(struct intel_encoder *encoder, · line 3598
Quoted 2 lines
drivers/gpu/drm/i915/intel_ddi.c +0
-0switch (pipe_config->lane_count) {case 1 :
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx