ARM: imx: Update Novena to DM/DT
Subsystems (2)
v2 cover ARM: imx: Update Novena to DM/DT
Update Kosagi Novena to DM / DT and remove the warnings. This depends on the following patches / series:
https://patchwork.ozlabs.org/patch/1095618/
https://patchwork.ozlabs.org/patch/1101171/
https://patchwork.ozlabs.org/project/uboot/list/?series=108463
Marek Vasut (7):
ARM: dts: imx: novena: Import Novena DT from Linux
ARM: imx: novena: Enable DM pin control
ARM: imx: novena: Enable DM GPIO
ARM: imx: novena: Convert block devices to DM
ARM: imx: novena: Enable DM USB
ARM: imx: novena: Enable DM PCI
ARM: imx: novena: Convert to DM VIDEO
arch/arm/dts/Makefile | 3 +- arch/arm/dts/imx6q-novena.dts | 797 ++++++++++++++++++++++++++++++++++ board/kosagi/novena/novena.c | 77 +--- board/kosagi/novena/video.c | 3 + configs/novena_defconfig | 18 +- include/configs/novena.h | 9 +- 6 files changed, 838 insertions(+), 69 deletions(-) create mode 100644 arch/arm/dts/imx6q-novena.dts
Signature · 1 line
2.20.1
PATCH v2 1/7 ARM: dts: imx: novena: Import Novena DT from Linux
Import iMX6Q Novena device tree from Linux 5.1-rc7 37624b58542f . Enable DT control in full U-Boot .
---
V2: No change
--- arch/arm/dts/Makefile | 3 +- arch/arm/dts/imx6q-novena.dts | 792 ++++++++++++++++++++++++++++++++++ configs/novena_defconfig | 3 +- 3 files changed, 796 insertions(+), 2 deletions(-) create mode 100644 arch/arm/dts/imx6q-novena.dts
arch/arm/dts/Makefile +2 -1
@@ -535,7 +535,8 @@ dtb-$(CONFIG_MX53) += imx53-cx9020.dtb \ dtb-$(CONFIG_MX6Q) += \ imx6-apalis.dtb \ imx6q-display5.dtb \ - imx6q-logicpd.dtb + imx6q-logicpd.dtb \ + imx6q-novena.dtb dtb-$(CONFIG_TARGET_TBS2910) += \ imx6q-tbs2910.dtb
arch/arm/dts/imx6q-novena.dts new file +792 -0
792 lines not on this page · raw message
configs/novena_defconfig +2 -1
@@ -40,6 +40,8 @@ CONFIG_CMD_CACHE=y CONFIG_CMD_TIME=y CONFIG_CMD_EXT4_WRITE=y # CONFIG_SPL_PARTITION_UUIDS is not set +CONFIG_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="imx6q-novena" CONFIG_ENV_IS_IN_MMC=y CONFIG_DWC_AHSATA=y CONFIG_FSL_ESDHC=y
@@ -62,4 +64,3 @@ CONFIG_VIDEO_IPUV3=y CONFIG_VIDEO=y # CONFIG_VIDEO_SW_CURSOR is not set CONFIG_FAT_WRITE=y -CONFIG_OF_LIBFDT=y
Signature · 1 line
2.20.1
PATCH v2 1/7 ARM: dts: imx: novena: Import Novena DT
Quoted 6 lines
Import iMX6Q Novena device tree from Linux 5.1-rc7
37624b58542f. Enable DT control in full U-Boot .Signed-off-by Marek Vasut <[email protected]>Cc Fabio Estevam <[email protected]>Cc Stefano Babic <[email protected]>Cc Vagrant Cascadian <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH v2 2/7 ARM: imx: novena: Enable DM pin control
In reply to Marek VasutEnable DM pin control support on iMX6Q Novena.
---
V2: No change
--- configs/novena_defconfig | 5 +++++ 1 file changed, 5 insertions(+)
configs/novena_defconfig +5 -0
@@ -14,6 +14,7 @@ CONFIG_SPL_FS_FAT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_CMD_HDMIDETECT=y CONFIG_DISTRO_DEFAULTS=y +# CONFIG_SYS_MALLOC_F is not set CONFIG_FIT=y CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg,MX6Q" CONFIG_USE_BOOTARGS=y
@@ -29,6 +30,7 @@ CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y CONFIG_CMD_ASKENV=y CONFIG_CMD_EEPROM=y +CONFIG_CMD_DM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y
@@ -43,6 +45,7 @@ CONFIG_CMD_EXT4_WRITE=y CONFIG_OF_CONTROL=y CONFIG_DEFAULT_DEVICE_TREE="imx6q-novena" CONFIG_ENV_IS_IN_MMC=y +CONFIG_DM=y CONFIG_DWC_AHSATA=y CONFIG_FSL_ESDHC=y CONFIG_PHYLIB=y
@@ -50,6 +53,8 @@ CONFIG_PHY_MICREL=y CONFIG_PHY_MICREL_KSZ90X1=y CONFIG_MII=y CONFIG_PCI=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_IMX6=y CONFIG_USB=y CONFIG_USB_KEYBOARD=y CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP=y
Signature · 1 line
2.20.1
PATCH v2 2/7 ARM: imx: novena: Enable DM pin control
Quoted 5 lines
Enable DM pin control support on iMX6Q Novena.
Signed-off-by Marek Vasut <[email protected]>Cc Fabio Estevam <[email protected]>Cc Stefano Babic <[email protected]>Cc Vagrant Cascadian <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH v2 3/7 ARM: imx: novena: Enable DM GPIO
In reply to Marek VasutEnable DM GPIO support on iMX6Q Novena and fix up board code where applicable.
---
V2: No change
--- board/kosagi/novena/novena.c | 2 ++ board/kosagi/novena/video.c | 3 +++ configs/novena_defconfig | 1 + 3 files changed, 6 insertions(+)
board/kosagi/novena/novena.c +2 -0
@@ -83,6 +83,8 @@ int drv_keyboard_init(void) .tstc = novena_gpio_button_tstc, }; +gpio_request (NOVENA_BUTTON_GPIO ,"button" ); + error =input_init (&button_input,0 );if (error) {debug ("%s: Cannot set up input\n" , __func__);
board/kosagi/novena/video.c +3 -0
@@ -270,6 +270,7 @@ static void enable_lvds(struct display_info_t const *dev)return ;/* ITE IT6251 power enable. */ +gpio_request (NOVENA_ITE6251_PWR_GPIO ,"ite6251-power" );gpio_direction_output (NOVENA_ITE6251_PWR_GPIO ,0 );mdelay (10 );gpio_direction_output (NOVENA_ITE6251_PWR_GPIO ,1 );
@@ -447,6 +448,8 @@ void setup_display_lvds(void)/* Init the LVDS-to-eDP chip and if it succeeded, enable backlight. */ ret =it6251_init ();if (!ret) { +gpio_request (NOVENA_BACKLIGHT_PWR_GPIO ,"backlight-power" ); +gpio_request (NOVENA_BACKLIGHT_PWM_GPIO ,"backlight-pwm" );/* Backlight power enable. */ gpio_direction_output (NOVENA_BACKLIGHT_PWR_GPIO ,1 );/* PWM backlight pin, always on for full brightness. */
configs/novena_defconfig +1 -0
@@ -47,6 +47,7 @@ CONFIG_DEFAULT_DEVICE_TREE="imx6q-novena" CONFIG_ENV_IS_IN_MMC=y CONFIG_DM=y CONFIG_DWC_AHSATA=y +CONFIG_DM_GPIO=y CONFIG_FSL_ESDHC=y CONFIG_PHYLIB=y CONFIG_PHY_MICREL=y
Signature · 1 line
2.20.1
PATCH v2 3/7 ARM: imx: novena: Enable DM GPIO
Quoted 6 lines
Enable DM GPIO support on iMX6Q Novena and fix up board code where applicable.
Signed-off-by Marek Vasut <[email protected]>Cc Fabio Estevam <[email protected]>Cc Stefano Babic <[email protected]>Cc Vagrant Cascadian <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH v2 4/7 ARM: imx: novena: Convert block devices to DM
In reply to Marek VasutEnable DM block, DM MMC and DM SATA support on iMX6Q Novena convert board code to match the DM support.
---
V2: - Drop the ad-hoc sata binding, this is superseded by
CONFIG_DWC_AHSATA_AHCI=y resp. drivers/ata/dwc_ahsata.c
- Drop dangling setup_sata() call
--- arch/arm/dts/imx6q-novena.dts | 5 +++ board/kosagi/novena/novena.c | 62 +++-------------------------------- configs/novena_defconfig | 3 ++ include/configs/novena.h | 5 --- 4 files changed, 12 insertions(+), 63 deletions(-)
arch/arm/dts/imx6q-novena.dts +5 -0
@@ -61,6 +61,11 @@ reg = <0x10000000 0>; }; + aliases { + mmc0 = &usdhc3; + mmc1 = &usdhc2; + }; + chosen { stdout-path = &uart2; };
board/kosagi/novena/novena.c +4 -58
86 lines not on this page · raw message
configs/novena_defconfig +3 -0
@@ -13,6 +13,7 @@ CONFIG_SPL=y CONFIG_SPL_FS_FAT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_CMD_HDMIDETECT=y +CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y # CONFIG_SYS_MALLOC_F is not set CONFIG_FIT=y
@@ -48,6 +49,7 @@ CONFIG_ENV_IS_IN_MMC=y CONFIG_DM=y CONFIG_DWC_AHSATA=y CONFIG_DM_GPIO=y +CONFIG_DM_MMC=y CONFIG_FSL_ESDHC=y CONFIG_PHYLIB=y CONFIG_PHY_MICREL=y
@@ -56,6 +58,7 @@ CONFIG_MII=y CONFIG_PCI=y CONFIG_PINCTRL=y CONFIG_PINCTRL_IMX6=y +CONFIG_DM_SCSI=y CONFIG_USB=y CONFIG_USB_KEYBOARD=y CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP=y
include/configs/novena.h +0 -5
@@ -102,12 +102,7 @@#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08/* SATA Configs */ -#ifdef CONFIG_CMD_SATA -#define CONFIG_SYS_SATA_MAX_DEVICE 1 -#define CONFIG_DWC_AHSATA_PORT_ID 0 -#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR#define CONFIG_LBA48 -#endif /* UART */ #define CONFIG_MXC_UART
Signature · 1 line
2.20.1
PATCH v2 4/7 ARM: imx: novena: Convert block devices to DM
Quoted 6 lines
Enable DM block, DM MMC and DM SATA support on iMX6Q Novena convert board code to match the DM support.
Signed-off-by Marek Vasut <[email protected]>Cc Fabio Estevam <[email protected]>Cc Stefano Babic <[email protected]>Cc Vagrant Cascadian <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH v2 5/7 ARM: imx: novena: Enable DM USB
In reply to Marek VasutEnable DM USB support on iMX6Q Novena.
---
V2: No change
--- configs/novena_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/novena_defconfig +1 -0
@@ -60,6 +60,7 @@ CONFIG_PINCTRL=y CONFIG_PINCTRL_IMX6=y CONFIG_DM_SCSI=y CONFIG_USB=y +CONFIG_DM_USB=y CONFIG_USB_KEYBOARD=y CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP=y CONFIG_USB_GADGET=y
Signature · 1 line
2.20.1
PATCH v2 5/7 ARM: imx: novena: Enable DM USB
Quoted 5 lines
Enable DM USB support on iMX6Q Novena.
Signed-off-by Marek Vasut <[email protected]>Cc Fabio Estevam <[email protected]>Cc Stefano Babic <[email protected]>Cc Vagrant Cascadian <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH v2 6/7 ARM: imx: novena: Enable DM PCI
In reply to Marek VasutEnable DM PCI support on iMX6Q Novena.
---
V2: New patch
--- configs/novena_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/novena_defconfig +1 -0
@@ -56,6 +56,7 @@ CONFIG_PHY_MICREL=y CONFIG_PHY_MICREL_KSZ90X1=y CONFIG_MII=y CONFIG_PCI=y +CONFIG_DM_PCI=y CONFIG_PINCTRL=y CONFIG_PINCTRL_IMX6=y CONFIG_DM_SCSI=y
Signature · 1 line
2.20.1
PATCH v2 6/7 ARM: imx: novena: Enable DM PCI
Hi Marek,
Quoted 18 lines · Marek Vasut
Enable DM PCI support on iMX6Q Novena.
Signed-off-by Marek Vasut <[email protected]>Cc Fabio Estevam <[email protected]>Cc Stefano Babic <[email protected]>Cc Vagrant Cascadian <[email protected]>---
V2: New patch--- configs/novena_defconfig | 1 + 1 file changed, 1 insertion(+)configs/novena_defconfig +0
-0
configs/novena_defconfig CONFIG_PHY_MICREL=y · line 62
Quoted 7 lines
configs/novena_defconfig +1
-0@@ -56,6 +56,7 @@ CONFIG_PHY_MICREL=y CONFIG_PHY_MICREL_KSZ90X1=y CONFIG_MII=y CONFIG_PCI=y +CONFIG_DM_PCI=y CONFIG_PINCTRL=y CONFIG_PINCTRL_IMX6=y CONFIG_DM_SCSI=y
I cannot build novena with this enabled - do you see the same error or am I missing something ?
arm: + novena
+ pci_set_ops(hose,
+ ^~~~~~~~~~~+drivers/pci/pcie_imx.c:686:7: error:
?pci_hose_read_config_byte_via_dword? undeclared (first use in this function)
+ pci_hose_read_config_byte_via_dword,
+ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~+drivers/pci/pcie_imx.c:686:7: note: each undeclared identifier is reported only once for each function it appears in +drivers/pci/pcie_imx.c:687:7: error:
?pci_hose_read_config_word_via_dword? undeclared (first use in this function)
+ pci_hose_read_config_word_via_dword,+drivers/pci/pcie_imx.c:689:7: error:
?pci_hose_write_config_byte_via_dword? undeclared (first use in this function)
+ pci_hose_write_config_byte_via_dword,
+ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~+drivers/pci/pcie_imx.c:690:7: error:
?pci_hose_write_config_word_via_dword? undeclared (first use in this function)
+ pci_hose_write_config_word_via_dword,
+ pci_register_hose(hose); + ^~~~~~~~~~~~~~~~~ + hose->last_busno = pci_hose_scan(hose);
+ ^~~~~~~~~~~~~
+make[3]: *** [drivers/pci/pcie_imx.o] Error 1 +make[2]: *** [drivers/pci] Error 2
+make[1]: *** [drivers] Error 2
+make: *** [sub-make] Error 2w+drivers/pci/pcie_imx.c: In function ?imx_pcie_init?:w+drivers/pci/pcie_imx.c:685:2: warning: implicit declaration of function ?pci_set_ops? [-Wimplicit-function-declaration] w+drivers/pci/pcie_imx.c:697:3: warning: implicit declaration of function ?pci_register_hose? [-Wimplicit-function-declaration] w+drivers/pci/pcie_imx.c:698:22: warning: implicit declaration of function ?pci_hose_scan? [-Wimplicit-function-declaration]
Regards,
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH v2 6/7 ARM: imx: novena: Enable DM PCI
Quoted 63 lines · Stefano Babic
Hi Marek,
Quoted 18 lines · Marek Vasut
Enable DM PCI support on iMX6Q Novena.
Signed-off-by Marek Vasut <[email protected]>Cc Fabio Estevam <[email protected]>Cc Stefano Babic <[email protected]>Cc Vagrant Cascadian <[email protected]>---
V2: New patch--- configs/novena_defconfig | 1 + 1 file changed, 1 insertion(+)configs/novena_defconfig +0
-0configs/novena_defconfig CONFIG_PHY_MICREL=y · line 62
Quoted 7 lines
configs/novena_defconfig +1
-0@@ -56,6 +56,7 @@ CONFIG_PHY_MICREL=y CONFIG_PHY_MICREL_KSZ90X1=y CONFIG_MII=y CONFIG_PCI=y +CONFIG_DM_PCI=y CONFIG_PINCTRL=y CONFIG_PINCTRL_IMX6=y CONFIG_DM_SCSI=yI cannot build novena with this enabled - do you see the same error or am I missing something ?
arm: + novena
(quoted diff) +3
-0+ pci_set_ops(hose, + ^~~~~~~~~~~ +drivers/pci/pcie_imx.c:686:7: error:?pci_hose_read_config_byte_via_dword? undeclared (first use in this function)
(quoted diff) +3
-0+ pci_hose_read_config_byte_via_dword, + ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +drivers/pci/pcie_imx.c:686:7: note: each undeclared identifier isreported only once for each function it appears in
+drivers/pci/pcie_imx.c:687:7: error:
?pci_hose_read_config_word_via_dword? undeclared (first use in this function)(quoted diff) +2
-0+ pci_hose_read_config_word_via_dword, +drivers/pci/pcie_imx.c:689:7: error:?pci_hose_write_config_byte_via_dword? undeclared (first use in this function)
(quoted diff) +3
-0+ pci_hose_write_config_byte_via_dword, + ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +drivers/pci/pcie_imx.c:690:7: error:?pci_hose_write_config_word_via_dword? undeclared (first use in this function)
(quoted diff) +9
-0+ pci_hose_write_config_word_via_dword, + pci_register_hose(hose); + ^~~~~~~~~~~~~~~~~ + hose->last_busno = pci_hose_scan(hose); + ^~~~~~~~~~~~~ +make[3]: *** [drivers/pci/pcie_imx.o] Error 1 +make[2]: *** [drivers/pci] Error 2 +make[1]: *** [drivers] Error 2 +make: *** [sub-make] Error 2
Quoted 7 lines
w+drivers/pci/pcie_imx.c: In function ?imx_pcie_init?:w+drivers/pci/pcie_imx.c:685:2: warning: implicit declaration of function ?pci_set_ops? [-Wimplicit-function-declaration]w+drivers/pci/pcie_imx.c:697:3: warning: implicit declaration of function ?pci_register_hose? [-Wimplicit-function-declaration]w+drivers/pci/pcie_imx.c:698:22: warning: implicit declaration of function ?pci_hose_scan? [-Wimplicit-function-declaration]
I collected the patches here [1], CI passed:
https://github.com/marex/u-boot-imx/tree/imx-dm
Signature · 2 lines
Best regards, Marek Vasut
PATCH v2 6/7 ARM: imx: novena: Enable DM PCI
Quoted 74 lines · Marek Vasut
Quoted 63 lines · Stefano Babic
Hi Marek,
Quoted 18 lines · Marek Vasut
Enable DM PCI support on iMX6Q Novena.
Signed-off-by Marek Vasut <[email protected]>Cc Fabio Estevam <[email protected]>Cc Stefano Babic <[email protected]>Cc Vagrant Cascadian <[email protected]>---
V2: New patch--- configs/novena_defconfig | 1 + 1 file changed, 1 insertion(+)configs/novena_defconfig +0
-0configs/novena_defconfig CONFIG_PHY_MICREL=y · line 62
Quoted 7 lines
configs/novena_defconfig +1
-0@@ -56,6 +56,7 @@ CONFIG_PHY_MICREL=y CONFIG_PHY_MICREL_KSZ90X1=y CONFIG_MII=y CONFIG_PCI=y +CONFIG_DM_PCI=y CONFIG_PINCTRL=y CONFIG_PINCTRL_IMX6=y CONFIG_DM_SCSI=yI cannot build novena with this enabled - do you see the same error or am I missing something ?
arm: + novena
(quoted diff) +3
-0+ pci_set_ops(hose, + ^~~~~~~~~~~ +drivers/pci/pcie_imx.c:686:7: error:?pci_hose_read_config_byte_via_dword? undeclared (first use in this function)
(quoted diff) +3
-0+ pci_hose_read_config_byte_via_dword, + ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +drivers/pci/pcie_imx.c:686:7: note: each undeclared identifier isreported only once for each function it appears in
+drivers/pci/pcie_imx.c:687:7: error:
?pci_hose_read_config_word_via_dword? undeclared (first use in this function)(quoted diff) +2
-0+ pci_hose_read_config_word_via_dword, +drivers/pci/pcie_imx.c:689:7: error:?pci_hose_write_config_byte_via_dword? undeclared (first use in this function)
(quoted diff) +3
-0+ pci_hose_write_config_byte_via_dword, + ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +drivers/pci/pcie_imx.c:690:7: error:?pci_hose_write_config_word_via_dword? undeclared (first use in this function)
(quoted diff) +9
-0+ pci_hose_write_config_word_via_dword, + pci_register_hose(hose); + ^~~~~~~~~~~~~~~~~ + hose->last_busno = pci_hose_scan(hose); + ^~~~~~~~~~~~~ +make[3]: *** [drivers/pci/pcie_imx.o] Error 1 +make[2]: *** [drivers/pci] Error 2 +make[1]: *** [drivers] Error 2 +make: *** [sub-make] Error 2Quoted 7 lines
w+drivers/pci/pcie_imx.c: In function ?imx_pcie_init?:w+drivers/pci/pcie_imx.c:685:2: warning: implicit declaration of function ?pci_set_ops? [-Wimplicit-function-declaration]w+drivers/pci/pcie_imx.c:697:3: warning: implicit declaration of function ?pci_register_hose? [-Wimplicit-function-declaration]w+drivers/pci/pcie_imx.c:698:22: warning: implicit declaration of function ?pci_hose_scan? [-Wimplicit-function-declaration]I collected the patches here [1], CI passed:
Quoted 1 line
Fine, thanks - I had not applied your pcie patches before novena. I see you sent V2 for pcie, I am picking up the new version then
Thanks,
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH v2 6/7 ARM: imx: novena: Enable DM PCI
In reply to Marek VasutQuoted 5 lines
Enable DM PCI support on iMX6Q Novena.
Signed-off-by Marek Vasut <[email protected]>Cc Fabio Estevam <[email protected]>Cc Stefano Babic <[email protected]>Cc Vagrant Cascadian <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH v2 7/7 ARM: imx: novena: Convert to DM VIDEO
In reply to Marek VasutEnable DM Video support on iMX6Q Novena and fix minor details to restore previous behavior of the system.
---
V2: Print U-Boot version information on the LCD
--- board/kosagi/novena/novena.c | 13 +++++++++++++ configs/novena_defconfig | 6 +++--- include/configs/novena.h | 4 ++-- 3 files changed, 18 insertions(+), 5 deletions(-)
board/kosagi/novena/novena.c +13 -0
@@ -39,6 +39,7 @@#include <power/pmic.h> #include <power/pfuze100_pmic.h> #include <stdio_dev.h> +#include <video_console.h> #include "novena.h"
@@ -125,7 +126,19 @@ int board_init(void)int board_late_init (void ) {#if defined(CONFIG_VIDEO_IPUV3 ) +struct udevice *con; +char buf[DISPLAY_OPTIONS_BANNER_LENGTH ]; +int ret; +setup_display_lvds (); + + ret =uclass_get_device (UCLASS_VIDEO_CONSOLE ,0 , &con); +if (ret) +return ret; + +display_options_get_banner (false, buf,sizeof (buf)); +vidconsole_position_cursor (con,0 ,0 ); +vidconsole_put_string (con, buf);#endif return 0 ; }
configs/novena_defconfig +3 -3
@@ -4,6 +4,7 @@ CONFIG_SYS_TEXT_BASE=0x17800000 CONFIG_SPL_GPIO_SUPPORT=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_SYS_MALLOC_F_LEN=0x2000 CONFIG_MX6_DDRCAL=y CONFIG_TARGET_KOSAGI_NOVENA=y CONFIG_SPL_MMC_SUPPORT=y
@@ -15,7 +16,6 @@ CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_CMD_HDMIDETECT=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y -# CONFIG_SYS_MALLOC_F is not set CONFIG_FIT=y CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg,MX6Q" CONFIG_USE_BOOTARGS=y
@@ -71,7 +71,7 @@ CONFIG_USB_ETH_CDC=y CONFIG_USB_HOST_ETHER=y CONFIG_USB_ETHER_ASIX=y CONFIG_USB_ETHER_SMSC95XX=y +CONFIG_DM_VIDEO=y +CONFIG_SYS_WHITE_ON_BLACK=y CONFIG_VIDEO_IPUV3=y -CONFIG_VIDEO=y -# CONFIG_VIDEO_SW_CURSOR is not set CONFIG_FAT_WRITE=y
include/configs/novena.h +2 -2
@@ -119,14 +119,12 @@#endif /* Video output */ -#ifdef CONFIG_VIDEO #define CONFIG_VIDEO_BMP_RLE8 #define CONFIG_SPLASH_SCREEN #define CONFIG_BMP_16BPP #define CONFIG_VIDEO_LOGO #define CONFIG_IMX_HDMI #define CONFIG_IMX_VIDEO_SKIP -#endif /* Extra U-Boot environment. */ #ifndef CONFIG_SPL_BUILD
@@ -144,6 +142,8 @@"ramdisk_addr_r=0x28000000\0" \"fdt_addr_r=0x18000000\0" \"fdtfile=imx6q-novena.dtb\0" \ +"stdout=serial,vidconsole\0" \ +"stderr=serial,vidconsole\0" \"addcons=" \"setenv bootargs ${bootargs} " \"console=${consdev},${baudrate}\0" \
Signature · 1 line
2.20.1
PATCH v2 7/7 ARM: imx: novena: Convert to DM VIDEO
Quoted 6 lines
Enable DM Video support on iMX6Q Novena and fix minor details to restore previous behavior of the system.
Signed-off-by Marek Vasut <[email protected]>Cc Fabio Estevam <[email protected]>Cc Stefano Babic <[email protected]>Cc Vagrant Cascadian <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
v2 cover ARM: imx: Update Novena to DM/DT
In reply to Marek VasutQuoted 5 lines · Marek Vasut
Update Kosagi Novena to DM / DT and remove the warnings. This depends on the following patches / series:
https://patchwork.ozlabs.org/patch/1095618/
https://patchwork.ozlabs.org/patch/1101171/
These are now merged in 2019.07-rc3.
These were not yet.
I have two oustanding issues... with some files it sometimes fails to load one or more from SATA:
Retrieving file: /boot/initrd.img-5.0.0-trunk-armmp
20077960 bytes read in 375 ms (51.1 MiB/s)
Retrieving file: /boot/vmlinuz-5.0.0-trunk-armmp
4215296 bytes read in 40 ms (100.5 MiB/s)
append: root=UUID=9666ab0b-f932-4e2f-95d7-0e96a12a4540 ro quiet Retrieving file: /usr/lib/linux-image-5.0.0-trunk-armmp/imx6q-novena.dtb
CACHE: Misaligned operation at range [fafb5398, fafb6398]
CACHE: Misaligned operation at range [fafb5398, fafb6398]
ERROR: v7_outer_cache_inval_range - start address is not aligned - 0xfafb5398
ERROR: v7_outer_cache_inval_range - stop address is not aligned - 0xfafb6398
invalid extent block
It then falls back to one of the other kernels (using the extlinux.conf parsing) and succeeds. It consistantly gets a cache/alignment error with this specific file. A bit-for-bit identical .dtb loaded from another path works just fine. Older versions of u-boot boot this fine. Would some particular EXT4 flag possibly be causing issues?
Several other kernel+initrd+dtb combinations work fine.
I have not noticed issues loading from PXE.
The second issue is still using one out of four exposed USB ports fails and resets the board:
load usb 0:1 $kernel_addr_r misc/Binaries/linux/Image data abort
pc : [<fefbb67a>] lr : [<fefbb0fd>]
reloc pc : [<1783367a>] lr : [<178330fd>]
sp : faf7c6e8 ip : 00000003 fp : 00000005
r10: faf8b200 r9 : faf87ea0 r8 : 00000001
r7 : faf8b2c0 r6 : f9f7a040 r5 : faf7c710 r4 : 00000038
r3 : 0000006d r2 : f9f7a0a3 r1 : faf8b32c r0 : f9f7a09f
Flags: nzCv IRQs off FIQs off Mode SVC_32
Code: 4630fc5b 81f0e8bd e7d84606 bf082b2f (f822235c)
Resetting CPU ...
The three other usb ports work just fine with the same USB stick and file. All four ports work with 2019.01.
Despite those two issues somewhat significant issues... it does appear to work in general... so, with 2019.07-rc3 +
https://patchwork.ozlabs.org/project/uboot/list/?series=108463 and this series applied, with the above caveats:
live well,
vagrant
Quoted 18 lines
Marek Vasut (7):
ARM: dts: imx: novena: Import Novena DT from Linux
ARM: imx: novena: Enable DM pin control
ARM: imx: novena: Enable DM GPIO
ARM: imx: novena: Convert block devices to DM
ARM: imx: novena: Enable DM USB
ARM: imx: novena: Enable DM PCI
ARM: imx: novena: Convert to DM VIDEOarch/arm/dts/Makefile | 3 +- arch/arm/dts/imx6q-novena.dts | 797 ++++++++++++++++++++++++++++++++++ board/kosagi/novena/novena.c | 77 +--- board/kosagi/novena/video.c | 3 + configs/novena_defconfig | 18 +- include/configs/novena.h | 9 +- 6 files changed, 838 insertions(+), 69 deletions(-) create mode 100644 arch/arm/dts/imx6q-novena.dts
Quoted 5 lines
Cc Fabio Estevam <[email protected]>Cc Stefano Babic <[email protected]>Cc Vagrant Cascadian <[email protected]>Signature · 1 line
2.20.1
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 227 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190604/8b8f5db2/attachment.sig>
v2 cover ARM: imx: Update Novena to DM/DT
Quoted 1 line · Vagrant Cascadian
On 2019-05-17, Marek Vasut wrote:
Retried with a build from:
https://github.com/marex/u-boot-imx/tree/imx-dm
commit:7a381bb7edfd43aefc1dbfea6d574234ef9d7771
Which contains the two patchsets needed.
Quoted 17 lines
I have two oustanding issues... with some files it sometimes fails to load one or more from SATA:
Retrieving file:
/boot/initrd.img-5.0.0-trunk-armmp
20077960 bytes read in 375 ms (51.1 MiB/s)
Retrieving file:/boot/vmlinuz-5.0.0-trunk-armmp
4215296 bytes read in 40 ms (100.5 MiB/s)
append: root=UUID=9666ab0b-f932-4e2f-95d7-0e96a12a4540 ro quiet Retrieving file:/usr/lib/linux-image-5.0.0-trunk-armmp/imx6q-novena.dtb
CACHE: Misaligned operation at range [fafb5398,fafb6398]
CACHE: Misaligned operation at range [fafb5398,fafb6398]
ERROR:v7_outer_cache_inval_range- start address is not aligned -0xfafb5398
ERROR:v7_outer_cache_inval_range- stop address is not aligned -0xfafb6398
invalid extent block
Quoted 7 lines
It then falls back to one of the other kernels (using the extlinux.conf parsing) and succeeds. It consistantly gets a cache/alignment error with this specific file. A bit-for-bit identical .dtb loaded from another path works just fine. Older versions of u-boot boot this fine. Would some particular EXT4 flag possibly be causing issues?
Several other kernel+initrd+dtb combinations work fine.
Running "dcache off" before booting still produces the warnings/errors, but actually does boot successfully. Of course, it's much slower.
Quoted 12 lines
The second issue is still using one out of four exposed USB ports fails and resets the board:
load usb 0:1 $kernel_addr_r misc/Binaries/linux/Image data abort
pc : [<fefbb67a>] lr : [<fefbb0fd>]reloc pc : [<
1783367a>] lr : [<178330fd>]
sp :faf7c6e8ip : 00000003 fp : 00000005
r10:faf8b200r9 :faf87ea0r8 : 00000001
r7 :faf8b2c0r6 :f9f7a040r5 :faf7c710r4 : 00000038
r3 :0000006dr2 :f9f7a0a3r1 :faf8b32cr0 :f9f7a09f
Flags: nzCv IRQs off FIQs off ModeSVC_32
Quoted 5 lines
Code: 4630fc5b 81f0e8bd e7d84606 bf082b2f (f822235c)Resetting CPU ...
The three other usb ports work just fine with the same USB stick and file. All four ports work with 2019.01.
Got a bit-for-bit identical error on this one.
I was able to get the objdump output with the reloc pc value:
$ arm-linux-gnueabihf-objdump -d u-boot | grep 178337aa 178337aa: f822 3b02 strh.w r3, [r2], #2
Hope that's helpful!
live well,
vagrant
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 227 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190606/66fcebfb/attachment.sig>
v2 cover ARM: imx: Update Novena to DM/DT
Quoted 34 lines · Vagrant Cascadian
Quoted 1 line · Vagrant Cascadian
On 2019-05-17, Marek Vasut wrote:
Retried with a build from:
https://github.com/marex/u-boot-imx/tree/imx-dm
commit:7a381bb7edfd43aefc1dbfea6d574234ef9d7771Which contains the two patchsets needed.
Quoted 23 lines
I have two oustanding issues... with some files it sometimes fails to load one or more from SATA:
Retrieving file:
/boot/initrd.img-5.0.0-trunk-armmp
20077960 bytes read in 375 ms (51.1 MiB/s)
Retrieving file:/boot/vmlinuz-5.0.0-trunk-armmp
4215296 bytes read in 40 ms (100.5 MiB/s)
append: root=UUID=9666ab0b-f932-4e2f-95d7-0e96a12a4540 ro quiet Retrieving file:/usr/lib/linux-image-5.0.0-trunk-armmp/imx6q-novena.dtb
CACHE: Misaligned operation at range [fafb5398,fafb6398]
CACHE: Misaligned operation at range [fafb5398,fafb6398]
ERROR:v7_outer_cache_inval_range- start address is not aligned -0xfafb5398
ERROR:v7_outer_cache_inval_range- stop address is not aligned -0xfafb6398
invalid extent blockIt then falls back to one of the other kernels (using the extlinux.conf parsing) and succeeds. It consistantly gets a cache/alignment error with this specific file. A bit-for-bit identical .dtb loaded from another path works just fine. Older versions of u-boot boot this fine. Would some particular EXT4 flag possibly be causing issues?
Quoted 4 lines
Quoted 1 line
Several other kernel+initrd+dtb combinations work fine.
Running "dcache off" before booting still produces the warnings/errors, but actually does boot successfully. Of course, it's much slower.
Well, someone needs to debug this :-)
Quoted 18 lines
Quoted 12 lines
The second issue is still using one out of four exposed USB ports fails and resets the board:
load usb 0:1 $kernel_addr_r misc/Binaries/linux/Image data abort
pc : [<fefbb67a>] lr : [<fefbb0fd>]reloc pc : [<
1783367a>] lr : [<178330fd>]
sp :faf7c6e8ip : 00000003 fp : 00000005
r10:faf8b200r9 :faf87ea0r8 : 00000001
r7 :faf8b2c0r6 :f9f7a040r5 :faf7c710r4 : 00000038
r3 :0000006dr2 :f9f7a0a3r1 :faf8b32cr0 :f9f7a09f
Flags: nzCv IRQs off FIQs off ModeSVC_32Quoted 5 lines
Code: 4630fc5b 81f0e8bd e7d84606 bf082b2f (f822235c)Resetting CPU ...
The three other usb ports work just fine with the same USB stick and file. All four ports work with 2019.01.
Quoted 8 lines
Got a bit-for-bit identical error on this one.
I was able to get the objdump output with the reloc pc value:
$ arm-linux-gnueabihf-objdump -d u-boot | grep 178337aa 178337aa: f822 3b02 strh.w r3, [r2], #2Hope that's helpful!
Not at all, it basically says "writing unknown value to unknown offset in memory causes data abort". If you run ...objdump -lSD u-boot, you can likely find more information in the dump and also where/why it crashes.
Signature · 2 lines
Best regards, Marek Vasut
v2 cover ARM: imx: Update Novena to DM/DT
In reply to Vagrant CascadianQuoted 30 lines · Vagrant Cascadian
Quoted 5 lines · Marek Vasut
Update Kosagi Novena to DM / DT and remove the warnings. This depends on the following patches / series:
https://patchwork.ozlabs.org/patch/1095618/
https://patchwork.ozlabs.org/patch/1101171/These are now merged in 2019.07-rc3.
These were not yet.
I have two oustanding issues... with some files it sometimes fails to load one or more from SATA:
Retrieving file:
/boot/initrd.img-5.0.0-trunk-armmp
20077960 bytes read in 375 ms (51.1 MiB/s)
Retrieving file:/boot/vmlinuz-5.0.0-trunk-armmp
4215296 bytes read in 40 ms (100.5 MiB/s)
append: root=UUID=9666ab0b-f932-4e2f-95d7-0e96a12a4540 ro quiet Retrieving file:/usr/lib/linux-image-5.0.0-trunk-armmp/imx6q-novena.dtb
CACHE: Misaligned operation at range [fafb5398,fafb6398]
CACHE: Misaligned operation at range [fafb5398,fafb6398]
ERROR:v7_outer_cache_inval_range- start address is not aligned -0xfafb5398
ERROR:v7_outer_cache_inval_range- stop address is not aligned -0xfafb6398
invalid extent block
Quoted 5 lines
It then falls back to one of the other kernels (using the extlinux.conf parsing) and succeeds. It consistantly gets a cache/alignment error with this specific file. A bit-for-bit identical .dtb loaded from another path works just fine. Older versions of u-boot boot this fine. Would some particular EXT4 flag possibly be causing issues?
I don't know. Do you still run into this with u-boot/master ?
Quoted 17 lines
Several other kernel+initrd+dtb combinations work fine.
I have not noticed issues loading from PXE.
The second issue is still using one out of four exposed USB ports fails and resets the board:
load usb 0:1 $kernel_addr_r misc/Binaries/linux/Image data abort
pc : [<fefbb67a>] lr : [<fefbb0fd>]reloc pc : [<
1783367a>] lr : [<178330fd>]
sp :faf7c6e8ip : 00000003 fp : 00000005
r10:faf8b200r9 :faf87ea0r8 : 00000001
r7 :faf8b2c0r6 :f9f7a040r5 :faf7c710r4 : 00000038
r3 :0000006dr2 :f9f7a0a3r1 :faf8b32cr0 :f9f7a09f
Flags: nzCv IRQs off FIQs off ModeSVC_32
Quoted 5 lines
Code: 4630fc5b 81f0e8bd e7d84606 bf082b2f (f822235c)Resetting CPU ...
The three other usb ports work just fine with the same USB stick and file. All four ports work with 2019.01.
Can you debug it ? I think some of this was due to the EFI stuff , which I think was fixed since. Can you re-check that ?
v2 cover ARM: imx: Update Novena to DM/DT
Quoted 3 lines · Marek Vasut
Quoted 2 lines · Vagrant Cascadian
Quoted 1 line · Marek Vasut
Update Kosagi Novena to DM / DT and remove the warnings.
...
Quoted 17 lines
Quoted 17 lines
I have two oustanding issues... with some files it sometimes fails to load one or more from SATA:
Retrieving file:
/boot/initrd.img-5.0.0-trunk-armmp
20077960 bytes read in 375 ms (51.1 MiB/s)
Retrieving file:/boot/vmlinuz-5.0.0-trunk-armmp
4215296 bytes read in 40 ms (100.5 MiB/s)
append: root=UUID=9666ab0b-f932-4e2f-95d7-0e96a12a4540 ro quiet Retrieving file:/usr/lib/linux-image-5.0.0-trunk-armmp/imx6q-novena.dtb
CACHE: Misaligned operation at range [fafb5398,fafb6398]
CACHE: Misaligned operation at range [fafb5398,fafb6398]
ERROR:v7_outer_cache_inval_range- start address is not aligned -0xfafb5398
ERROR:v7_outer_cache_inval_range- stop address is not aligned -0xfafb6398
invalid extent block
Quoted 7 lines
Quoted 5 lines
It then falls back to one of the other kernels (using the extlinux.conf parsing) and succeeds. It consistantly gets a cache/alignment error with this specific file. A bit-for-bit identical .dtb loaded from another path works just fine. Older versions of u-boot boot this fine. Would some particular EXT4 flag possibly be causing issues?
I don't know. Do you still run into this with u-boot/master ?
Still occurring with 2019.10-rc2. Haven't tested with master yet.
Using "dcache off" before booting still outputs the CACHE and ERROR messages, but does successfully boot.
Quoted 15 lines
Quoted 15 lines
The second issue is still using one out of four exposed USB ports fails and resets the board:
load usb 0:1 $kernel_addr_r misc/Binaries/linux/Image data abort
pc : [<fefbb67a>] lr : [<fefbb0fd>]reloc pc : [<
1783367a>] lr : [<178330fd>]
sp :faf7c6e8ip : 00000003 fp : 00000005
r10:faf8b200r9 :faf87ea0r8 : 00000001
r7 :faf8b2c0r6 :f9f7a040r5 :faf7c710r4 : 00000038
r3 :0000006dr2 :f9f7a0a3r1 :faf8b32cr0 :f9f7a09f
Flags: nzCv IRQs off FIQs off ModeSVC_32Code: 4630fc5b 81f0e8bd e7d84606 bf082b2f (f822235c)Resetting CPU ...
Quoted 5 lines
Quoted 2 lines
The three other usb ports work just fine with the same USB stick and file. All four ports work with 2019.01.
Can you debug it ? I think some of this was due to the EFI stuff , which I think was fixed since. Can you re-check that ?
USB appears to be working fine with 2019.10-rc2.
live well,
vagrant
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 227 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190820/f9476fa2/attachment.sig>
[U-Boot] dcache issues with wandboard too (was: [PATCH V2 0/7] ARM: imx: Update Novena to DM/DT)
Quoted 28 lines · Vagrant Cascadian
Quoted 3 lines · Marek Vasut
Quoted 2 lines · Vagrant Cascadian
Quoted 1 line · Marek Vasut
Update Kosagi Novena to DM / DT and remove the warnings.
...
Quoted 23 lines
Quoted 22 lines
I have two oustanding issues... with some files it sometimes fails to load one or more from SATA:
Retrieving file:
/boot/initrd.img-5.0.0-trunk-armmp
20077960 bytes read in 375 ms (51.1 MiB/s)
Retrieving file:/boot/vmlinuz-5.0.0-trunk-armmp
4215296 bytes read in 40 ms (100.5 MiB/s)
append: root=UUID=9666ab0b-f932-4e2f-95d7-0e96a12a4540 ro quiet Retrieving file:/usr/lib/linux-image-5.0.0-trunk-armmp/imx6q-novena.dtb
CACHE: Misaligned operation at range [fafb5398,fafb6398]
CACHE: Misaligned operation at range [fafb5398,fafb6398]
ERROR:v7_outer_cache_inval_range- start address is not aligned -0xfafb5398
ERROR:v7_outer_cache_inval_range- stop address is not aligned -0xfafb6398
invalid extent blockIt then falls back to one of the other kernels (using the extlinux.conf parsing) and succeeds. It consistantly gets a cache/alignment error with this specific file. A bit-for-bit identical .dtb loaded from another path works just fine. Older versions of u-boot boot this fine. Would some particular EXT4 flag possibly be causing issues?
Quoted 6 lines
Quoted 1 line
I don't know. Do you still run into this with u-boot/master ?
Still occurring with 2019.10-rc2. Haven't tested with master yet.
Using "dcache off" before booting still outputs the CACHE and ERROR messages, but does successfully boot.
Also seeing this problem with wandboard solo with 2019.10-rc4 booting from microSD. Haven't retested with novena recently.
Setting CONFIG_SYS_DCACHE_OFF=y avoids the need to manually type "dcache off" ... though obviously doesn't address the real problem.
live well,
vagrant
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 227 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190926/d010c567/attachment.sig>
[U-Boot] dcache issues with wandboard too (was: [PATCH V2 0/7] ARM: imx: Update Novena to DM/DT)
Quoted 33 lines · Vagrant Cascadian
Quoted 32 lines · Vagrant Cascadian
Quoted 3 lines · Marek Vasut
Quoted 2 lines · Vagrant Cascadian
Quoted 1 line · Marek Vasut
Update Kosagi Novena to DM / DT and remove the warnings.
...
Quoted 17 lines
Quoted 17 lines
I have two oustanding issues... with some files it sometimes fails to load one or more from SATA:
Retrieving file:
/boot/initrd.img-5.0.0-trunk-armmp
20077960 bytes read in 375 ms (51.1 MiB/s)
Retrieving file:/boot/vmlinuz-5.0.0-trunk-armmp
4215296 bytes read in 40 ms (100.5 MiB/s)
append: root=UUID=9666ab0b-f932-4e2f-95d7-0e96a12a4540 ro quiet Retrieving file:/usr/lib/linux-image-5.0.0-trunk-armmp/imx6q-novena.dtb
CACHE: Misaligned operation at range [fafb5398,fafb6398]
CACHE: Misaligned operation at range [fafb5398,fafb6398]
ERROR:v7_outer_cache_inval_range- start address is not aligned -0xfafb5398
ERROR:v7_outer_cache_inval_range- stop address is not aligned -0xfafb6398
invalid extent blockQuoted 7 lines
Quoted 5 lines
It then falls back to one of the other kernels (using the extlinux.conf parsing) and succeeds. It consistantly gets a cache/alignment error with this specific file. A bit-for-bit identical .dtb loaded from another path works just fine. Older versions of u-boot boot this fine. Would some particular EXT4 flag possibly be causing issues?
I don't know. Do you still run into this with u-boot/master ?
Still occurring with 2019.10-rc2. Haven't tested with master yet.
Quoted 8 lines
Quoted 2 lines
Using "dcache off" before booting still outputs the CACHE and ERROR messages, but does successfully boot.
Also seeing this problem with wandboard solo with 2019.10-rc4 booting from microSD. Haven't retested with novena recently.
Setting
CONFIG_SYS_DCACHE_OFF=yavoids the need to manually type "dcache off" ... though obviously doesn't address the real problem.
Can you debug it further or prepare a reproducible testcase ?
v2 cover ARM: imx: Update Novena to DM/DT
In reply to Vagrant CascadianQuoted 51 lines · Vagrant Cascadian
Quoted 3 lines · Marek Vasut
Quoted 2 lines · Vagrant Cascadian
Quoted 1 line · Marek Vasut
Update Kosagi Novena to DM / DT and remove the warnings.
...
Quoted 17 lines
Quoted 17 lines
I have two oustanding issues... with some files it sometimes fails to load one or more from SATA:
Retrieving file:
/boot/initrd.img-5.0.0-trunk-armmp
20077960 bytes read in 375 ms (51.1 MiB/s)
Retrieving file:/boot/vmlinuz-5.0.0-trunk-armmp
4215296 bytes read in 40 ms (100.5 MiB/s)
append: root=UUID=9666ab0b-f932-4e2f-95d7-0e96a12a4540 ro quiet Retrieving file:/usr/lib/linux-image-5.0.0-trunk-armmp/imx6q-novena.dtb
CACHE: Misaligned operation at range [fafb5398,fafb6398]
CACHE: Misaligned operation at range [fafb5398,fafb6398]
ERROR:v7_outer_cache_inval_range- start address is not aligned -0xfafb5398
ERROR:v7_outer_cache_inval_range- stop address is not aligned -0xfafb6398
invalid extent blockQuoted 7 lines
Quoted 5 lines
It then falls back to one of the other kernels (using the extlinux.conf parsing) and succeeds. It consistantly gets a cache/alignment error with this specific file. A bit-for-bit identical .dtb loaded from another path works just fine. Older versions of u-boot boot this fine. Would some particular EXT4 flag possibly be causing issues?
I don't know. Do you still run into this with u-boot/master ?
Still occurring with 2019.10-rc2. Haven't tested with master yet.
Using "dcache off" before booting still outputs the CACHE and ERROR messages, but does successfully boot.
Quoted 15 lines
Quoted 15 lines
The second issue is still using one out of four exposed USB ports fails and resets the board:
load usb 0:1 $kernel_addr_r misc/Binaries/linux/Image data abort
pc : [<fefbb67a>] lr : [<fefbb0fd>]reloc pc : [<
1783367a>] lr : [<178330fd>]
sp :faf7c6e8ip : 00000003 fp : 00000005
r10:faf8b200r9 :faf87ea0r8 : 00000001
r7 :faf8b2c0r6 :f9f7a040r5 :faf7c710r4 : 00000038
r3 :0000006dr2 :f9f7a0a3r1 :faf8b32cr0 :f9f7a09f
Flags: nzCv IRQs off FIQs off ModeSVC_32Code: 4630fc5b 81f0e8bd e7d84606 bf082b2f (f822235c)Resetting CPU ...
Quoted 7 lines
Quoted 5 lines
Quoted 2 lines
The three other usb ports work just fine with the same USB stick and file. All four ports work with 2019.01.
Can you debug it ? I think some of this was due to the EFI stuff , which I think was fixed since. Can you re-check that ?
USB appears to be working fine with 2019.10-rc2.
So what's the current status ?