Add support for the Purism Librem5 devkit
Subsystems (2)
v16 cover Add support for the Purism Librem5 devkit
The Librem5 devkit is based on the imx8mq from NXP. This is a default devicetree to boot the board to a command prompt.
Changes since v15:
Update the ti,minimum-sys-voltage for the PMIC.
Changes since v14:
Add regulator-always-on for the SNVS regulators.
Added pgc nodes.
Fixed charger pre-current.
Changes since v13:
Moved haptic motor from pwm-led to gpio-vibrator.
Cleaned up regulator node naming.
Whitescpace cleanup.
Re-indent pinmux stanzas.
Drop pwm2 node.
Drop MAINTAINERS patch.
Changes since v12:
Updated patch to vendor-prefixes.yaml.
Dropped always on from regulators.
Changes since v11:
Added reviewed-by tags.
Fixed subject typo.
Changes since v10:
Moved MAINTAINERS entry to "ARM/FREESCALE IMX" section
Changes since v9:
Added a MAINTAINERS entry for arm64 imx devicetree files.
Changes since v8:
Fixed license comment.
Changed regulators to all lower case.
Changed clock frequency for NXP errata e7805.
Dropped blank line.
Changes since v7:
More regulators always on for USB.
Add vbus regulator.
Drop vbat regulator.
Replace legacy "gpio-key,wakeup" with "wakeup-source".
Add vbus-supply to get rid of warning
imx8mq-usb-phy 382f0040.usb-phy: 382f0040.usb-phy supply vbus not found, using dummy regulator
Changes since v6:
Dropped unused regulators.
Fix regulator phandles case.
Dropped extra whitespace.
Changes since v5:
Added reviewed-by tags.
Moved USB port links to USB controller node.
Changes since v4:
Compiled against linux-next next-20190415. Added imx8mq to the arm yaml file.
Re-arrange regulator nodes to drop undefined supplies. Additional ordering for aesthetics.
Split some long lines.
Added lots of blank lines.
Moved pinctl muxes to where they are used. Cleaned out reg defintions from regulator nodes.
Changes since v3:
Freshly sorted and pressed nodes.
Change the backlight to an interpolated scale.
Dropped i2c2.
Dropped devkit version number to match debian MR.
Changes since v2:
Fixed incorrect phy-supply for the fsl-fec.
Dropped unused regulator property.
Fixup Makefile for linux-next.
Changes since v1:
Dropped config file.
Updated the board compatible label.
Changed node names to follow naming conventions.
Added a more complete regulator hierachy.
Removed unused nodes.
Removed unknown devices.
Fixed comment style.
Dropped undocumented properties.
Angus Ainslie (Purism) (3):
arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit
dt-bindings: Add an entry for Purism SPC
dt-bindings: arm: fsl: Add the imx8mq boards
.../devicetree/bindings/arm/fsl.yaml | 7 + .../devicetree/bindings/vendor-prefixes.yaml | 2 + arch/arm64/boot/dts/freescale/Makefile | 1 + .../dts/freescale/imx8mq-librem5-devkit.dts | 806 ++++++++++++++++++ 4 files changed, 816 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
Signature · 1 line
2.17.1
PATCH v16 1/3 arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit
This is for the development kit board for the Librem 5. The current level of support yields a working console and is able to boot userspace from the network or eMMC.
Additional subsystems that are active :
- Both USB ports
- SD card socket
- WiFi usdhc
- WWAN modem
- GNSS
- GPIO keys
- LEDs
- gyro
- magnetometer
- touchscreen
- pwm
- backlight
- haptic motor
--- arch/arm64/boot/dts/freescale/Makefile | 1 + .../dts/freescale/imx8mq-librem5-devkit.dts | 806 ++++++++++++++++++ 2 files changed, 807 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
arch/arm64/boot/dts/freescale/Makefile +1 -0
@@ -22,6 +22,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts new file +806 -0
806 lines not on this page · raw message
Signature · 1 line
2.17.1
Re: [PATCH v16 1/3] arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit
Quoted 20 lines · Angus Ainslie (Purism)
This is for the development kit board for the Librem 5. The current level of support yields a working console and is able to boot userspace from the network or eMMC.
Additional subsystems that are active :
- Both USB ports
- SD card socket
- WiFi usdhc
- WWAN modem
- GNSS
- GPIO keys
- LEDs
- gyro
- magnetometer
- touchscreen
- pwm
- backlight
- haptic motor
Quoted 2 lines
Signed-off-by Angus Ainslie (Purism) <[email protected]>Reviewed-by Fabio Estevam <[email protected]>
Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
PATCH v16 2/3 dt-bindings: Add an entry for Purism SPC
In reply to Angus Ainslie (Purism)Add an entry for Purism, SPC
--- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/vendor-prefixes.yaml +2 -0
@@ -735,6 +735,8 @@ patternProperties: description: PROBOX2 (by W2COMP Co., Ltd.) "^pulsedlight,.*": description: PulsedLight, Inc + "^purism,.*": + description: Purism, SPC "^qca,.*": description: Qualcomm Atheros, Inc. "^qcom,.*":
Signature · 1 line
2.17.1
PATCH v16 3/3 dt-bindings: arm: fsl: Add the imx8mq boards
In reply to Angus Ainslie (Purism)Add an entry for imx8mq based boards
--- Documentation/devicetree/bindings/arm/fsl.yaml | 7 +++++++ 1 file changed, 7 insertions(+)
Documentation/devicetree/bindings/arm/fsl.yaml +7 -0
@@ -177,6 +177,13 @@ properties: - fsl,imx8mm-evk # i.MX8MM EVK Board - const: fsl,imx8mm + - description: i.MX8MQ based Boards + items: + - enum: + - fsl,imx8mq-evk # i.MX8MQ EVK Board + - purism,librem5-devkit # Purism Librem5 devkit + - const: fsl,imx8mq + - description: i.MX8QXP based Boards items: - enum:
Signature · 1 line
2.17.1
Shawn Guo
AppliedQuoted 4 lines · Angus Ainslie (Purism)
Angus Ainslie (Purism) (3):
arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit
dt-bindings: Add an entry for Purism SPC
dt-bindings: arm: fsl: Add the imx8mq boards
Applied all, thanks.
Quoted 7 lines · Shawn Guo
Quoted 4 lines · Angus Ainslie (Purism)
Angus Ainslie (Purism) (3):
arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit
dt-bindings: Add an entry for Purism SPC
dt-bindings: arm: fsl: Add the imx8mq boardsApplied all, thanks.
Thanks Shawn !