Skip to contentSkip to conversation

rockchip: rk3399: Use spl_board_init in SPL, TPL

PATCH New Jagan Teki 5 participants 18 messages Jun 20, 2019 – Nov 28, 2019 5 messages not in the archive

Subsystems (3)
lore
Share & tools
lore

Jagan Teki

author
#0 lore raw

v2 cover rockchip: rk3399: Use spl_board_init in SPL, TPL

This is v2 set for previous v1. No much diff, except the latest rebase.

Usually spl_board_init has preloader_console_init which would help to print boot up banner during SPL and TPL.

The current rk3399 lacking that in few of the boards, this series make reuse of spl_board_init in SPL and TPL stages.

with this series:
================

U-Boot TPL 2019.07-rc1-00243-g3f0cad6bd2 (May 08 2019 - 11:29:32 +0530) Trying to boot from BOOTROM
Returning to boot ROM...

U-Boot SPL 2019.07-rc1-00243-g3f0cad6bd2 (May 08 2019 - 11:29:32 +0530) Trying to boot from MMC1

U-Boot 2019.07-rc1-00243-g3f0cad6bd2 (May 08 2019 - 11:29:32 +0530)

Model: FriendlyElec NanoPC-T4
DRAM:  3.9 GiB
MMC:   dwmmc@fe310000: 2, dwmmc@fe320000: 1, sdhci@fe330000: 0

Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial@ff1a0000
Out:   serial@ff1a0000
Err:   serial@ff1a0000
Model: FriendlyElec NanoPC-T4
Net:   eth0: ethernet@fe300000
Hit any key to stop autoboot:  0 

=>

without this series:
===================

U-Boot TPL board init
Trying to boot from BOOTROM
Returning to boot ROM...
U-Boot SPL board init
Trying to boot from MMC1

U-Boot 2019.07-rc1-00243-g3f0cad6bd2 (May 08 2019 - 11:29:32 +0530)

Model: FriendlyElec NanoPC-T4
DRAM:  3.9 GiB
MMC:   dwmmc@fe310000: 2, dwmmc@fe320000: 1, sdhci@fe330000: 0

Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial@ff1a0000
Out:   serial@ff1a0000
Err:   serial@ff1a0000
Model: FriendlyElec NanoPC-T4
Net:   eth0: ethernet@fe300000
Hit any key to stop autoboot:  0 

=>

Any inputs?
Jagan.

Jagan Teki (8):
board: rk3399: Drop explicit uart enablement in spl_board_init
rockchip: rk3399: Support common spl_board_init
rockchip: rk3399: spl: Mark printascii into debug
rockchip: rk3399: Move u-boot, dm-pre-reloc of uart0, uart2
rockchip: rk3399: Enable SPL_BOARD_INIT
rockchip: rk3399: tpl: Add spl_board_init
rockchip: rk3399: tpl: Mark printascii into debug
rockchip: rk3399: Enable TPL_BOARD_INIT

 arch/arm/dts/rk3399-gru.dtsi                  |  1 -
 arch/arm/dts/rk3399-puma.dtsi                 |  1 -
 arch/arm/dts/rk3399-u-boot.dtsi               |  8 +++
 arch/arm/mach-rockchip/Kconfig                |  2 +
 arch/arm/mach-rockchip/rk3399-board-spl.c     | 65 ++++++++++++++++++-
 arch/arm/mach-rockchip/rk3399-board-tpl.c     |  9 ++-
 board/rockchip/evb_rk3399/evb-rk3399.c        | 29 ---------
 .../puma_rk3399/puma-rk3399.c                 | 58 -----------------
 board/vamrs/rock960_rk3399/rock960-rk3399.c   | 31 ---------
 configs/puma-rk3399_defconfig                 |  1 -
 10 files changed, 82 insertions(+), 123 deletions(-)
Signature · 6 lines
2.18.0.321.gffc6fa0e3

_______________________________________________
U-Boot mailing list
[email protected]
https://lists.denx.de/listinfo/u-boot

A message that is not in the archive (sent off-list or not yet received): 20190620185506.11449-1-jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org

#2 lore raw

PATCH v2 1/8 board: rk3399: Drop explicit uart enablement in spl_board_init

preloader_console_init is used for printing SPL boot banner that usually called from spl_board_init.

The current spl_board_init in evb and rock960 is enabling explicit pinctrl, debug uart prior to calling preloader_console_init which eventually not required since board_init_f is already enabled debug uart.

So, drop those explicit enablement calls from spl_board_init of evb, rock960.

Tested this by enabling CONFIG_SPL_BOARD_INIT and adding u-boot,dm-pre-reloc property for uart node.

---
 board/rockchip/evb_rk3399/evb-rk3399.c      | 23 +------------------
 board/vamrs/rock960_rk3399/rock960-rk3399.c | 25 +--------------------
 2 files changed, 2 insertions(+), 46 deletions(-)
board/rockchip/evb_rk3399/evb-rk3399.c +1 -22
index bf2ad98c47..769b5d146f 100644
@@ -6,7 +6,6 @@
 #include <common.h>
 #include <dm.h>
 #include <dm/pinctrl.h>
-#include <dm/uclass-internal.h>
 #include <asm/arch-rockchip/periph.h>
 #include <power/regulator.h>
 #include <spl.h>
@@ -68,27 +67,7 @@ out:
 
 void spl_board_init(void)
 {
-	struct udevice *pinctrl;
-	int ret;
-
-	ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl);
-	if (ret) {
-		debug("%s: Cannot find pinctrl device\n", __func__);
-		goto err;
-	}
-
-	/* Enable debug UART */
-	ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_UART_DBG);
-	if (ret) {
-		debug("%s: Failed to set up console UART\n", __func__);
-		goto err;
-	}
-
 	preloader_console_init();
-	return;
-err:
-	printf("%s: Error %d\n", __func__, ret);
 
-	/* No way to report error here */
-	hang();
+	return;
 }
board/vamrs/rock960_rk3399/rock960-rk3399.c +1 -24
index 0f5ef3a09a..018e4b55b8 100644
@@ -5,9 +5,6 @@
 
 #include <common.h>
 #include <dm.h>
-#include <dm/pinctrl.h>
-#include <dm/uclass-internal.h>
-#include <asm/arch-rockchip/periph.h>
 #include <power/regulator.h>
 #include <spl.h>
 
@@ -24,27 +21,7 @@ int board_init(void)
 
 void spl_board_init(void)
 {
-	struct udevice *pinctrl;
-	int ret;
-
-	ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl);
-	if (ret) {
-		debug("%s: Cannot find pinctrl device\n", __func__);
-		goto err;
-	}
-
-	/* Enable debug UART */
-	ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_UART_DBG);
-	if (ret) {
-		debug("%s: Failed to set up console UART\n", __func__);
-		goto err;
-	}
-
 	preloader_console_init();
-	return;
-err:
-	printf("%s: Error %d\n", __func__, ret);
 
-	/* No way to report error here */
-	hang();
+	return;
 }
Signature · 1 line
2.18.0.321.gffc6fa0e3
Reviewed-by on v2 1/8
#3 lore raw

Re: [PATCH v2 1/8] board: rk3399: Drop explicit uart enablement in spl_board_init

Hi Jagan,

Quoted 8 lines · Jagan Teki

preloader_console_init is used for printing SPL boot banner that usually called from spl_board_init.

The current spl_board_init in evb and rock960 is enabling explicit pinctrl, debug uart prior to calling preloader_console_init which eventually not required since board_init_f is already enabled debug uart.

Quoted 7 lines

So, drop those explicit enablement calls from spl_board_init of evb, rock960.

Tested this by enabling CONFIG_SPL_BOARD_INIT and adding u-boot,dm-pre-reloc property for uart node.

Thanks,
- Kever

Quoted 79 lines
---
 board/rockchip/evb_rk3399/evb-rk3399.c      | 23 +------------------
 board/vamrs/rock960_rk3399/rock960-rk3399.c | 25 +--------------------
 2 files changed, 2 insertions(+), 46 deletions(-)
board/rockchip/evb_rk3399/evb-rk3399.c +1 -22
index bf2ad98c47..769b5d146f 100644
@@ -6,7 +6,6 @@
 #include <common.h>
 #include <dm.h>
 #include <dm/pinctrl.h>
-#include <dm/uclass-internal.h>
 #include <asm/arch-rockchip/periph.h>
 #include <power/regulator.h>
 #include <spl.h>
@@ -68,27 +67,7 @@ out:
 
 void spl_board_init(void)
 {
-	struct udevice *pinctrl;
-	int ret;
-
-	ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl);
-	if (ret) {
-		debug("%s: Cannot find pinctrl device\n", __func__);
-		goto err;
-	}
-
-	/* Enable debug UART */
-	ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_UART_DBG);
-	if (ret) {
-		debug("%s: Failed to set up console UART\n", __func__);
-		goto err;
-	}
-
 	preloader_console_init();
-	return;
-err:
-	printf("%s: Error %d\n", __func__, ret);
 
-	/* No way to report error here */
-	hang();
+	return;
 }
board/vamrs/rock960_rk3399/rock960-rk3399.c +0 -18
index 0f5ef3a09a..018e4b55b8 100644
@@ -5,9 +5,6 @@
 
 #include <common.h>
 #include <dm.h>
-#include <dm/pinctrl.h>
-#include <dm/uclass-internal.h>
-#include <asm/arch-rockchip/periph.h>
 #include <power/regulator.h>
 #include <spl.h>
 
@@ -24,27 +21,7 @@ int board_init(void)
 
 void spl_board_init(void)
 {
-	struct udevice *pinctrl;
-	int ret;
-
-	ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl);
-	if (ret) {
-		debug("%s: Cannot find pinctrl device\n", __func__);
-		goto err;
-	}
-
-	/* Enable debug UART */
-	ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_UART_DBG);
-	if (ret) {
-		debug("%s: Failed to set up console UART\n", __func__);
-		goto err;
-	}

board/vamrs/rock960_rk3399/rock960-rk3399.c int board_init(void) · line 27

Quoted 10 lines
board/vamrs/rock960_rk3399/rock960-rk3399.c +1 -6
-
 	preloader_console_init();
-	return;
-err:
-	printf("%s: Error %d\n", __func__, ret);
 
-	/* No way to report error here */
-	hang();
+	return;
 }

_______________________________________________
U-Boot mailing list
[email protected]
https://lists.denx.de/listinfo/u-boot

#4 lore raw

PATCH v2 2/8 rockchip: rk3399: Support common spl_board_init

In reply to a message not in the archive

Support common spl_board_init by moving code from puma board file into, common rk3399-board-spl.c.

Part of the code has sysreset-gpio, regulators_enable_boot_on but right now only puma board is using this with relevant config options rest remains common for all targets.

---
 arch/arm/mach-rockchip/rk3399-board-spl.c     | 63 +++++++++++++++++++
 board/rockchip/evb_rk3399/evb-rk3399.c        |  8 ---
 .../puma_rk3399/puma-rk3399.c                 | 58 -----------------
 board/vamrs/rock960_rk3399/rock960-rk3399.c   |  8 ---
 4 files changed, 63 insertions(+), 74 deletions(-)
arch/arm/mach-rockchip/rk3399-board-spl.c +63 -0
index 800ca80022..65c98b697d 100644
@@ -11,13 +11,16 @@
 #include <spl.h>
 #include <spl_gpio.h>
 #include <syscon.h>
+#include <asm/gpio.h>
 #include <asm/io.h>
 #include <asm/arch-rockchip/bootrom.h>
 #include <asm/arch-rockchip/clock.h>
+#include <asm/arch-rockchip/cru_rk3399.h>
 #include <asm/arch-rockchip/grf_rk3399.h>
 #include <asm/arch-rockchip/hardware.h>
 #include <asm/arch-rockchip/periph.h>
 #include <asm/arch-rockchip/sys_proto.h>
+#include <power/regulator.h>
 #include <dm/pinctrl.h>
 
 void board_return_to_bootrom(void)
@@ -202,6 +205,66 @@ void board_init_f(ulong dummy)
 	}
 }
 
+#if defined(SPL_GPIO_SUPPORT)
+static void rk3399_force_power_on_reset(void)
+{
+	ofnode node;
+	struct gpio_desc sysreset_gpio;
+
+	debug("%s: trying to force a power-on reset\n", __func__);
+
+	node = ofnode_path("/config");
+	if (!ofnode_valid(node)) {
+		debug("%s: no /config node?\n", __func__);
+		return;
+	}
+
+	if (gpio_request_by_name_nodev(node, "sysreset-gpio", 0,
+				       &sysreset_gpio, GPIOD_IS_OUT)) {
+		debug("%s: could not find a /config/sysreset-gpio\n", __func__);
+		return;
+	}
+
+	dm_gpio_set_value(&sysreset_gpio, 1);
+}
+#endif
+
+void spl_board_init(void)
+{
+#if defined(SPL_GPIO_SUPPORT)
+	struct rk3399_cru *cru = rockchip_get_cru();
+
+	/*
+	 * The RK3399 resets only 'almost all logic' (see also in the TRM
+	 * "3.9.4 Global software reset"), when issuing a software reset.
+	 * This may cause issues during boot-up for some configurations of
+	 * the application software stack.
+	 *
+	 * To work around this, we test whether the last reset reason was
+	 * a power-on reset and (if not) issue an overtemp-reset to reset
+	 * the entire module.
+	 *
+	 * While this was previously fixed by modifying the various places
+	 * that could generate a software reset (e.g. U-Boot's sysreset
+	 * driver, the ATF or Linux), we now have it here to ensure that
+	 * we no longer have to track this through the various components.
+	 */
+	if (cru->glb_rst_st != 0)
+		rk3399_force_power_on_reset();
+#endif
+
+#if defined(SPL_DM_REGULATOR)
+	/*
+	 * Turning the eMMC and SPI back on (if disabled via the Qseven
+	 * BIOS_ENABLE) signal is done through a always-on regulator).
+	 */
+	if (regulators_enable_boot_on(false))
+		debug("%s: Cannot enable boot on regulator\n", __func__);
+#endif
+
+	preloader_console_init();
+}
+
 #ifdef CONFIG_SPL_LOAD_FIT
 int board_fit_config_name_match(const char *name)
 {
board/rockchip/evb_rk3399/evb-rk3399.c +0 -8
index 769b5d146f..c600553ff6 100644
@@ -8,7 +8,6 @@
 #include <dm/pinctrl.h>
 #include <asm/arch-rockchip/periph.h>
 #include <power/regulator.h>
-#include <spl.h>
 
 int board_init(void)
 {
@@ -64,10 +63,3 @@ int board_init(void)
 out:
 	return 0;
 }
-
-void spl_board_init(void)
-{
-	preloader_console_init();
-
-	return;
-}
board/theobroma-systems/puma_rk3399/puma-rk3399.c +0 -58

72 lines not on this page · raw message

board/vamrs/rock960_rk3399/rock960-rk3399.c +0 -8
index 018e4b55b8..2eb7120e84 100644
@@ -6,7 +6,6 @@
 #include <common.h>
 #include <dm.h>
 #include <power/regulator.h>
-#include <spl.h>
 
 int board_init(void)
 {
@@ -18,10 +17,3 @@ int board_init(void)
 
 	return 0;
 }
-
-void spl_board_init(void)
-{
-	preloader_console_init();
-
-	return;
-}
Signature · 1 line
2.18.0.321.gffc6fa0e3
Reviewed-by on v2 2/8
#5 lore raw

Re: [PATCH v2 2/8] rockchip: rk3399: Support common spl_board_init

Hi Jagan,

Quoted 8 lines · Jagan Teki

Support common spl_board_init by moving code from puma board file into, common rk3399-board-spl.c.

Part of the code has sysreset-gpio, regulators_enable_boot_on but right now only puma board is using this with relevant config options rest remains common for all targets.

Thanks,
- Kever

Quoted 209 lines
---
 arch/arm/mach-rockchip/rk3399-board-spl.c     | 63 +++++++++++++++++++
 board/rockchip/evb_rk3399/evb-rk3399.c        |  8 ---
 .../puma_rk3399/puma-rk3399.c                 | 58 -----------------
 board/vamrs/rock960_rk3399/rock960-rk3399.c   |  8 ---
 4 files changed, 63 insertions(+), 74 deletions(-)
arch/arm/mach-rockchip/rk3399-board-spl.c +63 -0
index 800ca80022..65c98b697d 100644
@@ -11,13 +11,16 @@
 #include <spl.h>
 #include <spl_gpio.h>
 #include <syscon.h>
+#include <asm/gpio.h>
 #include <asm/io.h>
 #include <asm/arch-rockchip/bootrom.h>
 #include <asm/arch-rockchip/clock.h>
+#include <asm/arch-rockchip/cru_rk3399.h>
 #include <asm/arch-rockchip/grf_rk3399.h>
 #include <asm/arch-rockchip/hardware.h>
 #include <asm/arch-rockchip/periph.h>
 #include <asm/arch-rockchip/sys_proto.h>
+#include <power/regulator.h>
 #include <dm/pinctrl.h>
 
 void board_return_to_bootrom(void)
@@ -202,6 +205,66 @@ void board_init_f(ulong dummy)
 	}
 }
 
+#if defined(SPL_GPIO_SUPPORT)
+static void rk3399_force_power_on_reset(void)
+{
+	ofnode node;
+	struct gpio_desc sysreset_gpio;
+
+	debug("%s: trying to force a power-on reset\n", __func__);
+
+	node = ofnode_path("/config");
+	if (!ofnode_valid(node)) {
+		debug("%s: no /config node?\n", __func__);
+		return;
+	}
+
+	if (gpio_request_by_name_nodev(node, "sysreset-gpio", 0,
+				       &sysreset_gpio, GPIOD_IS_OUT)) {
+		debug("%s: could not find a /config/sysreset-gpio\n", __func__);
+		return;
+	}
+
+	dm_gpio_set_value(&sysreset_gpio, 1);
+}
+#endif
+
+void spl_board_init(void)
+{
+#if defined(SPL_GPIO_SUPPORT)
+	struct rk3399_cru *cru = rockchip_get_cru();
+
+	/*
+	 * The RK3399 resets only 'almost all logic' (see also in the TRM
+	 * "3.9.4 Global software reset"), when issuing a software reset.
+	 * This may cause issues during boot-up for some configurations of
+	 * the application software stack.
+	 *
+	 * To work around this, we test whether the last reset reason was
+	 * a power-on reset and (if not) issue an overtemp-reset to reset
+	 * the entire module.
+	 *
+	 * While this was previously fixed by modifying the various places
+	 * that could generate a software reset (e.g. U-Boot's sysreset
+	 * driver, the ATF or Linux), we now have it here to ensure that
+	 * we no longer have to track this through the various components.
+	 */
+	if (cru->glb_rst_st != 0)
+		rk3399_force_power_on_reset();
+#endif
+
+#if defined(SPL_DM_REGULATOR)
+	/*
+	 * Turning the eMMC and SPI back on (if disabled via the Qseven
+	 * BIOS_ENABLE) signal is done through a always-on regulator).
+	 */
+	if (regulators_enable_boot_on(false))
+		debug("%s: Cannot enable boot on regulator\n", __func__);
+#endif
+
+	preloader_console_init();
+}
+
 #ifdef CONFIG_SPL_LOAD_FIT
 int board_fit_config_name_match(const char *name)
 {
board/rockchip/evb_rk3399/evb-rk3399.c +0 -8
index 769b5d146f..c600553ff6 100644
@@ -8,7 +8,6 @@
 #include <dm/pinctrl.h>
 #include <asm/arch-rockchip/periph.h>
 #include <power/regulator.h>
-#include <spl.h>
 
 int board_init(void)
 {
@@ -64,10 +63,3 @@ int board_init(void)
 out:
 	return 0;
 }
-
-void spl_board_init(void)
-{
-	preloader_console_init();
-
-	return;
-}
board/theobroma-systems/puma_rk3399/puma-rk3399.c +0 -58
index c6b509c109..251cd2d566 100644
@@ -13,10 +13,8 @@
 #include <dm/pinctrl.h>
 #include <dm/uclass-internal.h>
 #include <asm/io.h>
-#include <asm/gpio.h>
 #include <asm/setup.h>
 #include <asm/arch-rockchip/clock.h>
-#include <asm/arch-rockchip/cru_rk3399.h>
 #include <asm/arch-rockchip/hardware.h>
 #include <asm/arch-rockchip/grf_rk3399.h>
 #include <asm/arch-rockchip/periph.h>
@@ -38,62 +36,6 @@ int board_init(void)
 	return 0;
 }
 
-static void rk3399_force_power_on_reset(void)
-{
-	ofnode node;
-	struct gpio_desc sysreset_gpio;
-
-	debug("%s: trying to force a power-on reset\n", __func__);
-
-	node = ofnode_path("/config");
-	if (!ofnode_valid(node)) {
-		debug("%s: no /config node?\n", __func__);
-		return;
-	}
-
-	if (gpio_request_by_name_nodev(node, "sysreset-gpio", 0,
-				       &sysreset_gpio, GPIOD_IS_OUT)) {
-		debug("%s: could not find a /config/sysreset-gpio\n", __func__);
-		return;
-	}
-
-	dm_gpio_set_value(&sysreset_gpio, 1);
-}
-
-void spl_board_init(void)
-{
-	int  ret;
-	struct rk3399_cru *cru = rockchip_get_cru();
-
-	/*
-	 * The RK3399 resets only 'almost all logic' (see also in the TRM
-	 * "3.9.4 Global software reset"), when issuing a software reset.
-	 * This may cause issues during boot-up for some configurations of
-	 * the application software stack.
-	 *
-	 * To work around this, we test whether the last reset reason was
-	 * a power-on reset and (if not) issue an overtemp-reset to reset
-	 * the entire module.
-	 *
-	 * While this was previously fixed by modifying the various places
-	 * that could generate a software reset (e.g. U-Boot's sysreset
-	 * driver, the ATF or Linux), we now have it here to ensure that
-	 * we no longer have to track this through the various components.
-	 */
-	if (cru->glb_rst_st != 0)
-		rk3399_force_power_on_reset();
-
-	/*
-	 * Turning the eMMC and SPI back on (if disabled via the Qseven
-	 * BIOS_ENABLE) signal is done through a always-on regulator).
-	 */
-	ret = regulators_enable_boot_on(false);
-	if (ret)
-		debug("%s: Cannot enable boot on regulator\n", __func__);
-
-	preloader_console_init();
-}
-
 static void setup_macaddr(void)
 {
 #if CONFIG_IS_ENABLED(CMD_NET)
board/vamrs/rock960_rk3399/rock960-rk3399.c +0 -1
index 018e4b55b8..2eb7120e84 100644
@@ -6,7 +6,6 @@
 #include <common.h>
 #include <dm.h>
 #include <power/regulator.h>
-#include <spl.h>
 
 int board_init(void)
 {

board/vamrs/rock960_rk3399/rock960-rk3399.c int board_init(void) · line 27

Quoted 10 lines
board/vamrs/rock960_rk3399/rock960-rk3399.c +0 -7
@@ -18,10 +17,3 @@ int board_init(void)
 
 	return 0;
 }
-
-void spl_board_init(void)
-{
-	preloader_console_init();
-
-	return;
-}

_______________________________________________
U-Boot mailing list
[email protected]
https://lists.denx.de/listinfo/u-boot

#6 lore raw

Re: [PATCH v2 2/8] rockchip: rk3399: Support common spl_board_init

In reply to Jagan Teki
Quoted 38 lines · Jagan Teki

Support common spl_board_init by moving code from puma board file into, common rk3399-board-spl.c.

Part of the code has sysreset-gpio, regulators_enable_boot_on but right now only puma board is using this with relevant config options rest remains common for all targets.

---
 arch/arm/mach-rockchip/rk3399-board-spl.c     | 63 +++++++++++++++++++
 board/rockchip/evb_rk3399/evb-rk3399.c        |  8 ---
 .../puma_rk3399/puma-rk3399.c                 | 58 -----------------
 board/vamrs/rock960_rk3399/rock960-rk3399.c   |  8 ---
 4 files changed, 63 insertions(+), 74 deletions(-)
arch/arm/mach-rockchip/rk3399-board-spl.c +3 -0
index 800ca80022..65c98b697d 100644
@@ -11,13 +11,16 @@
 #include <spl.h>
 #include <spl_gpio.h>
 #include <syscon.h>
+#include <asm/gpio.h>
 #include <asm/io.h>
 #include <asm/arch-rockchip/bootrom.h>
 #include <asm/arch-rockchip/clock.h>
+#include <asm/arch-rockchip/cru_rk3399.h>
 #include <asm/arch-rockchip/grf_rk3399.h>
 #include <asm/arch-rockchip/hardware.h>
 #include <asm/arch-rockchip/periph.h>
 #include <asm/arch-rockchip/sys_proto.h>
+#include <power/regulator.h>
 #include <dm/pinctrl.h>
 
 void board_return_to_bootrom(void)

arch/arm/mach-rockchip/rk3399-board-spl.c void board_init_f(ulong dummy) · line 208

Quoted 4 lines
arch/arm/mach-rockchip/rk3399-board-spl.c +1 -0
@@ -202,6 +205,66 @@ void board_init_f(ulong dummy)
        }
 }
 
+#if defined(SPL_GPIO_SUPPORT)

That hasn't been compile tested since "defined(SPL_GPIO_SUPPORT)" ensures that this code never compiles.

It should be CONFIG_SPL_GPIO_SUPPORT instead, and it won't compile due to missing header in this case.

Unfortunately code won't work even with missing include added since something else is broken and it fails to request gpio.

Quoted 189 lines
arch/arm/mach-rockchip/rk3399-board-spl.c +59 -0
+static void rk3399_force_power_on_reset(void)
+{
+       ofnode node;
+       struct gpio_desc sysreset_gpio;
+
+       debug("%s: trying to force a power-on reset\n", __func__);
+
+       node = ofnode_path("/config");
+       if (!ofnode_valid(node)) {
+               debug("%s: no /config node?\n", __func__);
+               return;
+       }
+
+       if (gpio_request_by_name_nodev(node, "sysreset-gpio", 0,
+                                      &sysreset_gpio, GPIOD_IS_OUT)) {
+               debug("%s: could not find a /config/sysreset-gpio\n", __func__);
+               return;
+       }
+
+       dm_gpio_set_value(&sysreset_gpio, 1);
+}
+#endif
+
+void spl_board_init(void)
+{
+#if defined(SPL_GPIO_SUPPORT)
+       struct rk3399_cru *cru = rockchip_get_cru();
+
+       /*
+        * The RK3399 resets only 'almost all logic' (see also in the TRM
+        * "3.9.4 Global software reset"), when issuing a software reset.
+        * This may cause issues during boot-up for some configurations of
+        * the application software stack.
+        *
+        * To work around this, we test whether the last reset reason was
+        * a power-on reset and (if not) issue an overtemp-reset to reset
+        * the entire module.
+        *
+        * While this was previously fixed by modifying the various places
+        * that could generate a software reset (e.g. U-Boot's sysreset
+        * driver, the ATF or Linux), we now have it here to ensure that
+        * we no longer have to track this through the various components.
+        */
+       if (cru->glb_rst_st != 0)
+               rk3399_force_power_on_reset();
+#endif
+
+#if defined(SPL_DM_REGULATOR)
+       /*
+        * Turning the eMMC and SPI back on (if disabled via the Qseven
+        * BIOS_ENABLE) signal is done through a always-on regulator).
+        */
+       if (regulators_enable_boot_on(false))
+               debug("%s: Cannot enable boot on regulator\n", __func__);
+#endif
+
+       preloader_console_init();
+}
+
 #ifdef CONFIG_SPL_LOAD_FIT
 int board_fit_config_name_match(const char *name)
 {
board/rockchip/evb_rk3399/evb-rk3399.c +0 -8
index 769b5d146f..c600553ff6 100644
@@ -8,7 +8,6 @@
 #include <dm/pinctrl.h>
 #include <asm/arch-rockchip/periph.h>
 #include <power/regulator.h>
-#include <spl.h>
 
 int board_init(void)
 {
@@ -64,10 +63,3 @@ int board_init(void)
 out:
        return 0;
 }
-
-void spl_board_init(void)
-{
-       preloader_console_init();
-
-       return;
-}
board/theobroma-systems/puma_rk3399/puma-rk3399.c +0 -58
index c6b509c109..251cd2d566 100644
@@ -13,10 +13,8 @@
 #include <dm/pinctrl.h>
 #include <dm/uclass-internal.h>
 #include <asm/io.h>
-#include <asm/gpio.h>
 #include <asm/setup.h>
 #include <asm/arch-rockchip/clock.h>
-#include <asm/arch-rockchip/cru_rk3399.h>
 #include <asm/arch-rockchip/hardware.h>
 #include <asm/arch-rockchip/grf_rk3399.h>
 #include <asm/arch-rockchip/periph.h>
@@ -38,62 +36,6 @@ int board_init(void)
        return 0;
 }
 
-static void rk3399_force_power_on_reset(void)
-{
-       ofnode node;
-       struct gpio_desc sysreset_gpio;
-
-       debug("%s: trying to force a power-on reset\n", __func__);
-
-       node = ofnode_path("/config");
-       if (!ofnode_valid(node)) {
-               debug("%s: no /config node?\n", __func__);
-               return;
-       }
-
-       if (gpio_request_by_name_nodev(node, "sysreset-gpio", 0,
-                                      &sysreset_gpio, GPIOD_IS_OUT)) {
-               debug("%s: could not find a /config/sysreset-gpio\n", __func__);
-               return;
-       }
-
-       dm_gpio_set_value(&sysreset_gpio, 1);
-}
-
-void spl_board_init(void)
-{
-       int  ret;
-       struct rk3399_cru *cru = rockchip_get_cru();
-
-       /*
-        * The RK3399 resets only 'almost all logic' (see also in the TRM
-        * "3.9.4 Global software reset"), when issuing a software reset.
-        * This may cause issues during boot-up for some configurations of
-        * the application software stack.
-        *
-        * To work around this, we test whether the last reset reason was
-        * a power-on reset and (if not) issue an overtemp-reset to reset
-        * the entire module.
-        *
-        * While this was previously fixed by modifying the various places
-        * that could generate a software reset (e.g. U-Boot's sysreset
-        * driver, the ATF or Linux), we now have it here to ensure that
-        * we no longer have to track this through the various components.
-        */
-       if (cru->glb_rst_st != 0)
-               rk3399_force_power_on_reset();
-
-       /*
-        * Turning the eMMC and SPI back on (if disabled via the Qseven
-        * BIOS_ENABLE) signal is done through a always-on regulator).
-        */
-       ret = regulators_enable_boot_on(false);
-       if (ret)
-               debug("%s: Cannot enable boot on regulator\n", __func__);
-
-       preloader_console_init();
-}
-
 static void setup_macaddr(void)
 {
 #if CONFIG_IS_ENABLED(CMD_NET)
board/vamrs/rock960_rk3399/rock960-rk3399.c +0 -9
index 018e4b55b8..2eb7120e84 100644
@@ -6,7 +6,6 @@
 #include <common.h>
 #include <dm.h>
 #include <power/regulator.h>
-#include <spl.h>
 
 int board_init(void)
 {
@@ -18,10 +17,3 @@ int board_init(void)
 
        return 0;
 }
-
-void spl_board_init(void)
-{
-       preloader_console_init();
-
-       return;
-}
--

2.18.0.321.gffc6fa0e3

Quoted 4 lines

_______________________________________________
U-Boot mailing list
[email protected]
https://lists.denx.de/listinfo/u-boot

_______________________________________________
U-Boot mailing list
[email protected]
https://lists.denx.de/listinfo/u-boot

#7 lore raw

PATCH v2 3/8 rockchip: rk3399: spl: Mark printascii into debug

In reply to a message not in the archive

Now, we have spl_board_init with preloader_console_init that indeed show SPL banner.

So mark the 'U-Boot SPL board init' print into debug.

---
 arch/arm/mach-rockchip/rk3399-board-spl.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-rockchip/rk3399-board-spl.c +1 -1
index 65c98b697d..890d80025f 100644
@@ -164,7 +164,7 @@ void board_init_f(ulong dummy)
 	 * printhex8(0x1234);
 	 * printascii("string");
 	 */
-	printascii("U-Boot SPL board init\n");
+	debug("U-Boot SPL board init\n");
 #endif
 
 	ret = spl_early_init();
Signature · 1 line
2.18.0.321.gffc6fa0e3

A message that is not in the archive (sent off-list or not yet received): 20190620185506.11449-4-jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org

Reviewed-by
#9 lore raw

Re: [PATCH v2 3/8] rockchip: rk3399: spl: Mark printascii into debug

Hi Jagan,

Quoted 6 lines · Jagan Teki

Now, we have spl_board_init with preloader_console_init that indeed show SPL banner.

So mark the 'U-Boot SPL board init' print into debug.

Thanks,
- Kever

Quoted 17 lines
---
 arch/arm/mach-rockchip/rk3399-board-spl.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-rockchip/rk3399-board-spl.c +1 -1
index 65c98b697d..890d80025f 100644
@@ -164,7 +164,7 @@ void board_init_f(ulong dummy)
 	 * printhex8(0x1234);
 	 * printascii("string");
 	 */
-	printascii("U-Boot SPL board init\n");
+	debug("U-Boot SPL board init\n");
 #endif
 
 	ret = spl_early_init();
#10 lore raw

PATCH v2 4/8 rockchip: rk3399: Move u-boot, dm-pre-reloc of uart0, uart2

In reply to a message not in the archive

u-boot,dm-pre-reloc for uart0, uart2 indeed u-boot specific properties. Move them into rk3399-u-boot.dtsi so the boards which enabled these node will available during SPL.

---
 arch/arm/dts/rk3399-gru.dtsi    | 1 -
 arch/arm/dts/rk3399-puma.dtsi   | 1 -
 arch/arm/dts/rk3399-u-boot.dtsi | 8 ++++++++
 3 files changed, 8 insertions(+), 2 deletions(-)
arch/arm/dts/rk3399-gru.dtsi +0 -1
index ca0fc391b2..0e2e047180 100644
@@ -629,7 +629,6 @@ ap_i2c_audio: &i2c8 {
 
 &uart2 {
 	status = "okay";
-	u-boot,dm-pre-reloc;
 };
 
 &usb_host0_ohci {
arch/arm/dts/rk3399-puma.dtsi +0 -1
index 897e0bda85..74368da550 100644
@@ -639,7 +639,6 @@
 };
 
 &uart0 {
-	u-boot,dm-pre-reloc;
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_xfer &uart0_cts>;
 	status = "okay";
arch/arm/dts/rk3399-u-boot.dtsi +8 -0
index 0786c1193a..fcfce9ae02 100644
@@ -10,3 +10,11 @@
 &spi1 {
 	u-boot,dm-pre-reloc;
 };
+
+&uart0 {
+	u-boot,dm-pre-reloc;
+};
+
+&uart2 {
+	u-boot,dm-pre-reloc;
+};
Signature · 1 line
2.18.0.321.gffc6fa0e3

A message that is not in the archive (sent off-list or not yet received): 20190620185506.11449-5-jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org

Reviewed-by
#12 lore raw

Re: [PATCH v2 4/8] rockchip: rk3399: Move u-boot, dm-pre-reloc of uart0, uart2

Hi Jagan,

Quoted 5 lines · Jagan Teki

u-boot,dm-pre-reloc for uart0, uart2 indeed u-boot specific properties. Move them into rk3399-u-boot.dtsi so the boards which enabled these node will available during SPL.

Thanks,
- Kever

Quoted 46 lines
---
 arch/arm/dts/rk3399-gru.dtsi    | 1 -
 arch/arm/dts/rk3399-puma.dtsi   | 1 -
 arch/arm/dts/rk3399-u-boot.dtsi | 8 ++++++++
 3 files changed, 8 insertions(+), 2 deletions(-)
arch/arm/dts/rk3399-gru.dtsi +0 -1
index ca0fc391b2..0e2e047180 100644
@@ -629,7 +629,6 @@ ap_i2c_audio: &i2c8 {
 
 &uart2 {
 	status = "okay";
-	u-boot,dm-pre-reloc;
 };
 
 &usb_host0_ohci {
arch/arm/dts/rk3399-puma.dtsi +0 -1
index 897e0bda85..74368da550 100644
@@ -639,7 +639,6 @@
 };
 
 &uart0 {
-	u-boot,dm-pre-reloc;
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_xfer &uart0_cts>;
 	status = "okay";
arch/arm/dts/rk3399-u-boot.dtsi +8 -0
index 0786c1193a..fcfce9ae02 100644
@@ -10,3 +10,11 @@
 &spi1 {
 	u-boot,dm-pre-reloc;
 };
+
+&uart0 {
+	u-boot,dm-pre-reloc;
+};
+
+&uart2 {
+	u-boot,dm-pre-reloc;
+};
#13 lore raw

PATCH v2 5/8 rockchip: rk3399: Enable SPL_BOARD_INIT

In reply to a message not in the archive

Enable SPL_BOARD_INIT globally to rk3399, this would help to print the SPL banner during bootup.

---
 arch/arm/mach-rockchip/Kconfig | 1 +
 configs/puma-rk3399_defconfig  | 1 -
 2 files changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-rockchip/Kconfig +1 -0
index c05e3c3f48..ce039022df 100644
@@ -158,6 +158,7 @@ config ROCKCHIP_RK3399
 	select SPL
 	select SPL_ATF
 	select SPL_ATF_NO_PLATFORM_PARAM if SPL_ATF
+	select SPL_BOARD_INIT if SPL
 	select SPL_LOAD_FIT
 	select SPL_CLK if SPL
 	select SPL_PINCTRL if SPL
configs/puma-rk3399_defconfig +0 -1
index ebc78fb216..5cb2273a15 100644
@@ -21,7 +21,6 @@ CONFIG_MISC_INIT_R=y
 # CONFIG_DISPLAY_CPUINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
 CONFIG_SPL_TEXT_BASE=0xff8c2000
-CONFIG_SPL_BOARD_INIT=y
 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
 # CONFIG_SPL_LEGACY_IMAGE_SUPPORT is not set
 CONFIG_SPL_STACK_R=y
Signature · 1 line
2.18.0.321.gffc6fa0e3
Reviewed-by on v2 5/8
#14 lore raw

Re: [PATCH v2 5/8] rockchip: rk3399: Enable SPL_BOARD_INIT

Hi Jagan,

Quoted 4 lines · Jagan Teki

Enable SPL_BOARD_INIT globally to rk3399, this would help to print the SPL banner during bootup.

Thanks,
- Kever

Quoted 22 lines
---
 arch/arm/mach-rockchip/Kconfig | 1 +
 configs/puma-rk3399_defconfig  | 1 -
 2 files changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-rockchip/Kconfig +1 -0
index c05e3c3f48..ce039022df 100644
@@ -158,6 +158,7 @@ config ROCKCHIP_RK3399
 	select SPL
 	select SPL_ATF
 	select SPL_ATF_NO_PLATFORM_PARAM if SPL_ATF
+	select SPL_BOARD_INIT if SPL
 	select SPL_LOAD_FIT
 	select SPL_CLK if SPL
 	select SPL_PINCTRL if SPL
configs/puma-rk3399_defconfig +0 -0
index ebc78fb216..5cb2273a15 100644

configs/puma-rk3399_defconfig CONFIG_MISC_INIT_R=y · line 26

Quoted 7 lines
configs/puma-rk3399_defconfig +0 -1
@@ -21,7 +21,6 @@ CONFIG_MISC_INIT_R=y
 # CONFIG_DISPLAY_CPUINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
 CONFIG_SPL_TEXT_BASE=0xff8c2000
-CONFIG_SPL_BOARD_INIT=y
 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
 # CONFIG_SPL_LEGACY_IMAGE_SUPPORT is not set
 CONFIG_SPL_STACK_R=y

_______________________________________________
U-Boot mailing list
[email protected]
https://lists.denx.de/listinfo/u-boot

#15 lore raw

PATCH v2 6/8 rockchip: rk3399: tpl: Add spl_board_init

In reply to a message not in the archive

Add spl_board_init for TPL, that have TPL banner will help to print tpl boot prints.

---
 arch/arm/mach-rockchip/rk3399-board-tpl.c | 7 +++++++
 1 file changed, 7 insertions(+)
arch/arm/mach-rockchip/rk3399-board-tpl.c +7 -0
index 86d3ffe97c..72d0dd914e 100644
@@ -8,6 +8,7 @@
 #include <dm.h>
 #include <ram.h>
 #include <spl.h>
+#include <version.h>
 #include <asm/io.h>
 #include <asm/arch-rockchip/bootrom.h>
 
@@ -73,6 +74,12 @@ u32 spl_boot_device(void)
 	return BOOT_DEVICE_BOOTROM;
 }
 
+void spl_board_init(void)
+{
+	puts("\nU-Boot TPL "  PLAIN_VERSION " (" U_BOOT_DATE " - "
+	     U_BOOT_TIME " " U_BOOT_TZ ")\n");
+}
+
 #ifdef CONFIG_SPL_LOAD_FIT
 int board_fit_config_name_match(const char *name)
 {
Signature · 1 line
2.18.0.321.gffc6fa0e3
Reviewed-by on v2 6/8
#16 lore raw

Re: [PATCH v2 6/8] rockchip: rk3399: tpl: Add spl_board_init

Hi Jagan,

Quoted 4 lines · Jagan Teki

Add spl_board_init for TPL, that have TPL banner will help to print tpl boot prints.

Thanks,
- Kever

Quoted 19 lines
---
 arch/arm/mach-rockchip/rk3399-board-tpl.c | 7 +++++++
 1 file changed, 7 insertions(+)
arch/arm/mach-rockchip/rk3399-board-tpl.c +1 -0
index 86d3ffe97c..72d0dd914e 100644
@@ -8,6 +8,7 @@
 #include <dm.h>
 #include <ram.h>
 #include <spl.h>
+#include <version.h>
 #include <asm/io.h>
 #include <asm/arch-rockchip/bootrom.h>
 
@@ -73,6 +74,12 @@ u32 spl_boot_device(void)
 	return BOOT_DEVICE_BOOTROM;
 }

arch/arm/mach-rockchip/rk3399-board-tpl.c u32 spl_boot_device(void) · line 85

Quoted 10 lines
arch/arm/mach-rockchip/rk3399-board-tpl.c +6 -0
 
+void spl_board_init(void)
+{
+	puts("\nU-Boot TPL "  PLAIN_VERSION " (" U_BOOT_DATE " - "
+	     U_BOOT_TIME " " U_BOOT_TZ ")\n");
+}
+
 #ifdef CONFIG_SPL_LOAD_FIT
 int board_fit_config_name_match(const char *name)
 {

_______________________________________________
U-Boot mailing list
[email protected]
https://lists.denx.de/listinfo/u-boot

#17 lore raw

PATCH v2 7/8 rockchip: rk3399: tpl: Mark printascii into debug

In reply to a message not in the archive

Now, we have spl_board_init which has TPL banner prints.

So mark the 'U-Boot TPL board init' print into debug.

---
 arch/arm/mach-rockchip/rk3399-board-tpl.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-rockchip/rk3399-board-tpl.c +1 -1
index 72d0dd914e..4a301249b4 100644
@@ -47,7 +47,7 @@ void board_init_f(ulong dummy)
 	 * printhex8(0x1234);
 	 * printascii("string");
 	 */
-	printascii("U-Boot TPL board init\n");
+	debug("U-Boot TPL board init\n");
 #endif
 	ret = spl_early_init();
 	if (ret) {
Signature · 1 line
2.18.0.321.gffc6fa0e3

A message that is not in the archive (sent off-list or not yet received): 20190620185506.11449-8-jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org

Reviewed-by
#19 lore raw

Re: [PATCH v2 7/8] rockchip: rk3399: tpl: Mark printascii into debug

Hi Jagan,

Quoted 5 lines · Jagan Teki

Now, we have spl_board_init which has TPL banner prints.

So mark the 'U-Boot TPL board init' print into debug.

Thanks,
- Kever

Quoted 17 lines
---
 arch/arm/mach-rockchip/rk3399-board-tpl.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-rockchip/rk3399-board-tpl.c +1 -1
index 72d0dd914e..4a301249b4 100644
@@ -47,7 +47,7 @@ void board_init_f(ulong dummy)
 	 * printhex8(0x1234);
 	 * printascii("string");
 	 */
-	printascii("U-Boot TPL board init\n");
+	debug("U-Boot TPL board init\n");
 #endif
 	ret = spl_early_init();
 	if (ret) {
#20 lore raw

PATCH v2 8/8 rockchip: rk3399: Enable TPL_BOARD_INIT

In reply to a message not in the archive

Enable TPL_BOARD_INIT, this would help us to show
TPL boot prints.

---
 arch/arm/mach-rockchip/Kconfig | 1 +
 1 file changed, 1 insertion(+)
arch/arm/mach-rockchip/Kconfig +1 -0
index ce039022df..1d483be8b9 100644
@@ -184,6 +184,7 @@ config ROCKCHIP_RK3399
 	imply TPL_LIBCOMMON_SUPPORT
 	imply TPL_LIBGENERIC_SUPPORT
 	imply TPL_SYS_MALLOC_SIMPLE
+	imply TPL_BOARD_INIT
 	imply TPL_BOOTROM_SUPPORT
 	imply TPL_DRIVERS_MISC_SUPPORT
 	imply TPL_OF_CONTROL
Signature · 1 line
2.18.0.321.gffc6fa0e3

A message that is not in the archive (sent off-list or not yet received): 20190620185506.11449-9-jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org

Reviewed-by
#22 lore raw

Re: [PATCH v2 8/8] rockchip: rk3399: Enable TPL_BOARD_INIT

Hi Jagan,

Quoted 4 lines · Jagan Teki

Enable TPL_BOARD_INIT, this would help us to show
TPL boot prints.

Thanks,
- Kever

Quoted 16 lines
---
 arch/arm/mach-rockchip/Kconfig | 1 +
 1 file changed, 1 insertion(+)
arch/arm/mach-rockchip/Kconfig +1 -0
index ce039022df..1d483be8b9 100644
@@ -184,6 +184,7 @@ config ROCKCHIP_RK3399
 	imply TPL_LIBCOMMON_SUPPORT
 	imply TPL_LIBGENERIC_SUPPORT
 	imply TPL_SYS_MALLOC_SIMPLE
+	imply TPL_BOARD_INIT
 	imply TPL_BOOTROM_SUPPORT
 	imply TPL_DRIVERS_MISC_SUPPORT
 	imply TPL_OF_CONTROL