Skip to contentSkip to conversation

iio: adc: ad7124: Remove input number limitation

PATCH Superseded Mircea Caprioru 2 participants 8 messages Jun 24, 2019

Subsystems (3)

v3 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

PATCH v3 1/5 iio: adc: ad7124: Remove input number limitation

The driver limits the user to use only 4/8 differential inputs, but this device has the option to use pseudo-differential channels. This will increase the number of channels to be equal with the number of inputs so 8 channels for ad7124-4 and 16 for ad7124-8.

This patch removes the check between channel nodes and num_inputs value.

---

Changelog v2:
- nothing changed here

Changelog v3:
- nothing changed here

 drivers/iio/adc/ad7124.c | 7 -------
 1 file changed, 7 deletions(-)
drivers/iio/adc/ad7124.c +0 -7
index 659ef37d5fe8..810234db9c0d 100644
@@ -462,13 +462,6 @@ static int ad7124_of_parse_channel_config(struct iio_dev *indio_dev,
 		if (ret)
 			goto err;
 
-		if (ain[0] >= st->chip_info->num_inputs ||
-		    ain[1] >= st->chip_info->num_inputs) {
-			dev_err(indio_dev->dev.parent,
-				"Input pin number out of range.\n");
-			ret = -EINVAL;
-			goto err;
-		}
 		st->channel_config[channel].ain = AD7124_CHANNEL_AINP(ain[0]) |
 						  AD7124_CHANNEL_AINM(ain[1]);
 		st->channel_config[channel].bipolar =
Signature · 1 line
2.17.1
#1 lore raw

PATCH v3 2/5 iio: adc: ad7124: Add buffered input support

This patch adds the option to enable the buffered mode for positive and negative inputs. Each option can be enabled independently.

In buffered mode, the input channel feeds into a high impedance input stage of the buffer amplifier. Therefore, the input can tolerate significant source impedances and is tailored for direct connection to external resistive type sensors such as strain gages or RTDs.

---

Changelog v2:
- nothing changed here

Changelog v3:
- nothing changed here

 drivers/iio/adc/ad7124.c | 17 +++++++++++++++--
 1 file changed, 15 insertions(+), 2 deletions(-)
drivers/iio/adc/ad7124.c +15 -2
index 810234db9c0d..ab52c5e9ecb1 100644
@@ -61,6 +61,8 @@
 #define AD7124_CONFIG_REF_SEL(x)	FIELD_PREP(AD7124_CONFIG_REF_SEL_MSK, x)
 #define AD7124_CONFIG_PGA_MSK		GENMASK(2, 0)
 #define AD7124_CONFIG_PGA(x)		FIELD_PREP(AD7124_CONFIG_PGA_MSK, x)
+#define AD7124_CONFIG_IN_BUFF_MSK	GENMASK(7, 6)
+#define AD7124_CONFIG_IN_BUFF(x)	FIELD_PREP(AD7124_CONFIG_IN_BUFF_MSK, x)
 
 /* AD7124_FILTER_X */
 #define AD7124_FILTER_FS_MSK		GENMASK(10, 0)
@@ -108,6 +110,8 @@ struct ad7124_chip_info {
 struct ad7124_channel_config {
 	enum ad7124_ref_sel refsel;
 	bool bipolar;
+	bool buf_positive;
+	bool buf_negative;
 	unsigned int ain;
 	unsigned int vref_mv;
 	unsigned int pga_bits;
@@ -473,6 +477,11 @@ static int ad7124_of_parse_channel_config(struct iio_dev *indio_dev,
 		else
 			st->channel_config[channel].refsel = tmp;
 
+		st->channel_config[channel].buf_positive =
+			of_property_read_bool(child, "adi,buffered-positive");
+		st->channel_config[channel].buf_negative =
+			of_property_read_bool(child, "adi,buffered-negative");
+
 		*chan = ad7124_channel_template;
 		chan->address = channel;
 		chan->scan_index = channel;
@@ -492,7 +501,7 @@ static int ad7124_of_parse_channel_config(struct iio_dev *indio_dev,
 static int ad7124_setup(struct ad7124_state *st)
 {
 	unsigned int val, fclk, power_mode;
-	int i, ret;
+	int i, ret, tmp;
 
 	fclk = clk_get_rate(st->mclk);
 	if (!fclk)
@@ -525,8 +534,12 @@ static int ad7124_setup(struct ad7124_state *st)
 		if (ret < 0)
 			return ret;
 
+		tmp = (st->channel_config[i].buf_positive << 1)  +
+			st->channel_config[i].buf_negative;
+
 		val = AD7124_CONFIG_BIPOLAR(st->channel_config[i].bipolar) |
-		      AD7124_CONFIG_REF_SEL(st->channel_config[i].refsel);
+		      AD7124_CONFIG_REF_SEL(st->channel_config[i].refsel) |
+		      AD7124_CONFIG_IN_BUFF(tmp);
 		ret = ad_sd_write_reg(&st->sd, AD7124_CONFIG(i), 2, val);
 		if (ret < 0)
 			return ret;
Signature · 1 line
2.17.1
#2 lore raw

PATCH v3 3/5 iio: adc: ad7124: Shift to dynamic allocation for channel configuration

In reply to Mircea Caprioru

This patch changes the channel configuration member of the device structure from a fixed size array to a dynamic allocated one with a size equal to the number of channels specified in the device tree. This will ensure a more flexibility for compatible devices.

Ex. ad7124-4 - can have 4 differential or 8 pseudo-differential channels ad7124-8 - can have 8 differential or 16 pseudo-differential channels

Also the device can suspport any other combination of differential and pseudo-differential channels base on the physical number of inputs available.

---

Changelog v2:
- nothing changed here

Changelog v3:
- nothing changed here

 drivers/iio/adc/ad7124.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)
drivers/iio/adc/ad7124.c +8 -1
index ab52c5e9ecb1..edc6f1cc90b2 100644
@@ -121,7 +121,7 @@ struct ad7124_channel_config {
 struct ad7124_state {
 	const struct ad7124_chip_info *chip_info;
 	struct ad_sigma_delta sd;
-	struct ad7124_channel_config channel_config[4];
+	struct ad7124_channel_config *channel_config;
 	struct regulator *vref[4];
 	struct clk *mclk;
 	unsigned int adc_control;
@@ -439,6 +439,7 @@ static int ad7124_of_parse_channel_config(struct iio_dev *indio_dev,
 	struct ad7124_state *st = iio_priv(indio_dev);
 	struct device_node *child;
 	struct iio_chan_spec *chan;
+	struct ad7124_channel_config *chan_config;
 	unsigned int ain[2], channel = 0, tmp;
 	int ret;
 
@@ -453,8 +454,14 @@ static int ad7124_of_parse_channel_config(struct iio_dev *indio_dev,
 	if (!chan)
 		return -ENOMEM;
 
+	chan_config = devm_kcalloc(indio_dev->dev.parent, st->num_channels,
+				   sizeof(*chan_config), GFP_KERNEL);
+	if (!chan_config)
+		return -ENOMEM;
+
 	indio_dev->channels = chan;
 	indio_dev->num_channels = st->num_channels;
+	st->channel_config = chan_config;
 
 	for_each_available_child_of_node(np, child) {
 		ret = of_property_read_u32(child, "reg", &channel);
Signature · 1 line
2.17.1
#3 lore raw

PATCH v3 4/5 dt-bindings: iio: adc: Convert ad7124 documentation to YAML

In reply to Mircea Caprioru

Convert AD7124 bindings documentation to YAML format.

---

Changelog v2:
- modified SPDX license to GPL-2.0 OR BSD-2-Clause
- added regex for a range from 0 to 15
- added minimum and maximum constraints for reg property
- set type and range of values for adi,reference-select property
- used items for diff-channels property
- set bipolar, adi,buffered-positive and negative to type: boolean

Changelog v3:
- moved adi,buffered-positive and negative properties to own commit

 .../bindings/iio/adc/adi,ad7124.yaml          | 144 ++++++++++++++++++
 1 file changed, 144 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7124.yaml
Documentation/devicetree/bindings/iio/adc/adi,ad7124.yaml new file +144 -0
new file mode 100644
index 000000000000..1b3d84d08609
@@ -0,0 +1,144 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright 2019 Analog Devices Inc.
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/bindings/iio/adc/adi,ad7124.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices AD7124 ADC device driver
+
+maintainers:
+  - Stefan Popa <[email protected]>
+
+description: |
+  Bindings for the Analog Devices AD7124 ADC device. Datasheet can be
+  found here:
+    https://www.analog.com/media/en/technical-documentation/data-sheets/AD7124-8.pdf
+
+properties:
+  compatible:
+    enum:
+      - adi,ad7124-4
+      - adi,ad7124-8
+
+  reg:
+    description: SPI chip select number for the device
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+    description: phandle to the master clock (mclk)
+
+  clock-names:
+    items:
+      - const: mclk
+
+  interrupts:
+    description: IRQ line for the ADC
+    maxItems: 1
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+  refin1-supply:
+    description: refin1 supply can be used as reference for conversion.
+    maxItems: 1
+
+  refin2-supply:
+    description: refin2 supply can be used as reference for conversion.
+    maxItems: 1
+
+  avdd-supply:
+    description: avdd supply can be used as reference for conversion.
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - interrupts
+
+patternProperties:
+  "^channel@([0-9]|1[0-5])$":
+    type: object
+    description: |
+      Represents the external channels which are connected to the ADC.
+      See Documentation/devicetree/bindings/iio/adc/adc.txt.
+
+    properties:
+      reg:
+        description: |
+          The channel number. It can have up to 8 channels on ad7124-4
+          and 16 channels on ad7124-8, numbered from 0 to 15.
+        items:
+         minimum: 0
+         maximum: 15
+
+      adi,reference-select:
+        description: |
+          Select the reference source to use when converting on
+          the specific channel. Valid values are:
+          0: REFIN1(+)/REFIN1(−).
+          1: REFIN2(+)/REFIN2(−).
+          3: AVDD
+          If this field is left empty, internal reference is selected.
+        allOf:
+          - $ref: /schemas/types.yaml#/definitions/uint32
+          - enum: [0, 1, 3]
+
+      diff-channels:
+        description: see Documentation/devicetree/bindings/iio/adc/adc.txt
+        items:
+          minimum: 0
+          maximum: 15
+
+      bipolar:
+        description: see Documentation/devicetree/bindings/iio/adc/adc.txt
+        type: boolean
+
+    required:
+      - reg
+      - diff-channels
+
+examples:
+  - |
+    adc@0 {
+      compatible = "adi,ad7124-4";
+      reg = <0>;
+      spi-max-frequency = <5000000>;
+      interrupts = <25 2>;
+      interrupt-parent = <&gpio>;
+      refin1-supply = <&adc_vref>;
+      clocks = <&ad7124_mclk>;
+      clock-names = "mclk";
+
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      channel@0 {
+        reg = <0>;
+        diff-channels = <0 1>;
+        adi,reference-select = <0>;
+      };
+
+      channel@1 {
+        reg = <1>;
+        bipolar;
+        diff-channels = <2 3>;
+        adi,reference-select = <0>;
+      };
+
+      channel@2 {
+        reg = <2>;
+        diff-channels = <4 5>;
+      };
+
+      channel@3 {
+        reg = <3>;
+        diff-channels = <6 7>;
+      };
+    };
Signature · 1 line
2.17.1
#4 lore raw

Re: [PATCH V3 4/5] dt-bindings: iio: adc: Convert ad7124 documentation to YAML

Quoted 14 lines · Mircea Caprioru

Convert AD7124 bindings documentation to YAML format.

---

Changelog v2:
- modified SPDX license to GPL-2.0 OR BSD-2-Clause
- added regex for a range from 0 to 15
- added minimum and maximum constraints for reg property
- set type and range of values for adi,reference-select property
- used items for diff-channels property
- set bipolar, adi,buffered-positive and negative to type: boolean

Quoted 6 lines

Changelog v3:
- moved adi,buffered-positive and negative properties to own commit

 .../bindings/iio/adc/adi,ad7124.yaml          | 144 ++++++++++++++++++
 1 file changed, 144 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7124.yaml

The subject says 'Convert', but where's the removal of the old binding?

Rob

#5 lore raw

Re: [PATCH V3 4/5] dt-bindings: iio: adc: Convert ad7124 documentation to YAML

Quoted 28 lines · Rob Herring

[External]

Quoted 14 lines · Mircea Caprioru

Convert AD7124 bindings documentation to YAML format.

---

Changelog v2:
- modified SPDX license to GPL-2.0 OR BSD-2-Clause
- added regex for a range from 0 to 15
- added minimum and maximum constraints for reg property
- set type and range of values for adi,reference-select property
- used items for diff-channels property
- set bipolar, adi,buffered-positive and negative to type: boolean

Quoted 8 lines

Changelog v3:
- moved adi,buffered-positive and negative properties to own commit

 .../bindings/iio/adc/adi,ad7124.yaml          | 144
++++++++++++++++++
 1 file changed, 144 insertions(+)
 create mode 100644

Documentation/devicetree/bindings/iio/adc/adi,ad7124.yaml

Quoted 4 lines

The subject says 'Convert', but where's the removal of the old binding?

Rob

You are right I was not sure if I should also remove the old binding. I'll do a v4 to delete it in this patch.

Thanks,
Mircea

#6 lore raw

PATCH v3 5/5 dt-bindings: iio: adc: Add buffered input property

In reply to Mircea Caprioru

This patch adds the buffered mode device tree property for positive and negative inputs. Each option can be enabled independently.

In buffered mode, the input channel feeds into a high impedance input stage of the buffer amplifier. Therefore, the input can tolerate significant source impedances and is tailored for direct connection to external resistive type sensors such as strain gages or RTDs.

---

Changelog v3:
- added this separate commit for adi,buffered-positive and negative properties

 .../devicetree/bindings/iio/adc/adi,ad7124.yaml       | 11 +++++++++++
 1 file changed, 11 insertions(+)
Documentation/devicetree/bindings/iio/adc/adi,ad7124.yaml +11 -0
index 1b3d84d08609..cf494a08b837 100644
@@ -100,6 +100,14 @@ patternProperties:
         description: see Documentation/devicetree/bindings/iio/adc/adc.txt
         type: boolean
 
+      adi,buffered-positive:
+        description: Enable buffered mode for positive input.
+        type: boolean
+
+      adi,buffered-negative:
+        description: Enable buffered mode for negative input.
+        type: boolean
+
     required:
       - reg
       - diff-channels
@@ -123,6 +131,7 @@ examples:
         reg = <0>;
         diff-channels = <0 1>;
         adi,reference-select = <0>;
+        adi,buffered-positive;
       };
 
       channel@1 {
@@ -130,6 +139,8 @@ examples:
         bipolar;
         diff-channels = <2 3>;
         adi,reference-select = <0>;
+        adi,buffered-positive;
+        adi,buffered-negative;
       };
 
       channel@2 {
Signature · 1 line
2.17.1
Reviewed-by on v3 5/5
#7 lore raw

Re: [PATCH V3 5/5] dt-bindings: iio: adc: Add buffered input property

Quoted 10 lines · Mircea Caprioru

This patch adds the buffered mode device tree property for positive and negative inputs. Each option can be enabled independently.

In buffered mode, the input channel feeds into a high impedance input stage of the buffer amplifier. Therefore, the input can tolerate significant source impedances and is tailored for direct connection to external resistive type sensors such as strain gages or RTDs.

Quoted 8 lines

---

Changelog v3:
- added this separate commit for adi,buffered-positive and negative properties

 .../devicetree/bindings/iio/adc/adi,ad7124.yaml       | 11 +++++++++++
 1 file changed, 11 insertions(+)