ath10k: enabling tx stats support over pktlog
PATCH 1/1 ath10k: enabling tx stats support over pktlog
For QCA988X target, pktlog gives details of the tx bitrate which is used in the driver for station info.
Enabling pktlog by default will cause more interrupts in target to host CE pipe, which can impact more CPU usage for targets ex:WCN3990 and also not required for all other platforms (eg: WCN3990), for getting tx bitrate.
Enable pktlog only for QCA988X based on hardware params.
Tested HW : WCN3990
Tested FW : WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
--- drivers/net/wireless/ath/ath10k/core.c | 15 +++++++++++++++ drivers/net/wireless/ath/ath10k/hw.h | 3 +++ drivers/net/wireless/ath/ath10k/mac.c | 3 ++- 3 files changed, 20 insertions(+), 1 deletion(-)
drivers/net/wireless/ath/ath10k/core.c +15 -0
@@ -83,6 +83,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .rri_on_ddr = false, .hw_filter_reset_required = true, .fw_diag_ce_download = false, + .tx_stats_over_pktlog = true, }, { .id = QCA988X_HW_2_0_VERSION,
@@ -117,6 +118,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .rri_on_ddr = false, .hw_filter_reset_required = true, .fw_diag_ce_download = false, + .tx_stats_over_pktlog = true, }, { .id = QCA9887_HW_1_0_VERSION,
@@ -152,6 +154,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .rri_on_ddr = false, .hw_filter_reset_required = true, .fw_diag_ce_download = false, + .tx_stats_over_pktlog = false, }, { .id = QCA6174_HW_3_2_VERSION,
@@ -179,6 +182,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .uart_pin_workaround = true, + .tx_stats_over_pktlog = false, }, { .id = QCA6174_HW_2_1_VERSION,
@@ -213,6 +217,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .rri_on_ddr = false, .hw_filter_reset_required = true, .fw_diag_ce_download = false, + .tx_stats_over_pktlog = false, }, { .id = QCA6174_HW_2_1_VERSION,
@@ -247,6 +252,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .rri_on_ddr = false, .hw_filter_reset_required = true, .fw_diag_ce_download = false, + .tx_stats_over_pktlog = false, }, { .id = QCA6174_HW_3_0_VERSION,
@@ -281,6 +287,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .rri_on_ddr = false, .hw_filter_reset_required = true, .fw_diag_ce_download = false, + .tx_stats_over_pktlog = false, }, { .id = QCA6174_HW_3_2_VERSION,
@@ -318,6 +325,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .rri_on_ddr = false, .hw_filter_reset_required = true, .fw_diag_ce_download = true, + .tx_stats_over_pktlog = false, }, { .id = QCA99X0_HW_2_0_DEV_VERSION,
@@ -358,6 +366,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .rri_on_ddr = false, .hw_filter_reset_required = true, .fw_diag_ce_download = false, + .tx_stats_over_pktlog = false, }, { .id = QCA9984_HW_1_0_DEV_VERSION,
@@ -405,6 +414,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .rri_on_ddr = false, .hw_filter_reset_required = true, .fw_diag_ce_download = false, + .tx_stats_over_pktlog = false, }, { .id = QCA9888_HW_2_0_DEV_VERSION,
@@ -449,6 +459,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .rri_on_ddr = false, .hw_filter_reset_required = true, .fw_diag_ce_download = false, + .tx_stats_over_pktlog = false, }, { .id = QCA9377_HW_1_0_DEV_VERSION,
@@ -483,6 +494,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .rri_on_ddr = false, .hw_filter_reset_required = true, .fw_diag_ce_download = false, + .tx_stats_over_pktlog = false, }, { .id = QCA9377_HW_1_1_DEV_VERSION,
@@ -519,6 +531,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .rri_on_ddr = false, .hw_filter_reset_required = true, .fw_diag_ce_download = true, + .tx_stats_over_pktlog = false, }, { .id = QCA4019_HW_1_0_DEV_VERSION,
@@ -560,6 +573,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .rri_on_ddr = false, .hw_filter_reset_required = true, .fw_diag_ce_download = false, + .tx_stats_over_pktlog = false, }, { .id = WCN3990_HW_1_0_DEV_VERSION,
@@ -587,6 +601,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .rri_on_ddr = true, .hw_filter_reset_required = false, .fw_diag_ce_download = false, + .tx_stats_over_pktlog = false, }, };
drivers/net/wireless/ath/ath10k/hw.h +3 -0
@@ -612,6 +612,9 @@ struct ath10k_hw_params {* firmware bug */ bool uart_pin_workaround; + +/* tx stats support over pktlog */ +bool tx_stats_over_pktlog; };struct htt_rx_desc ;
drivers/net/wireless/ath/ath10k/mac.c +2 -1
@@ -7877,7 +7877,8 @@ ath10k_mac_op_assign_vif_chanctx(struct ieee80211_hw *hw, arvif->vdev_id, ret); } -if (ath10k_peer_stats_enabled (ar)) { +if (ath10k_peer_stats_enabled (ar) && + ar->hw_params.tx_stats_over_pktlog) { ar->pktlog_filter |=ATH10K_PKTLOG_PEER_STATS ; ret =ath10k_wmi_pdev_pktlog_enable (ar, ar->pktlog_filter);
Signature · 7 lines
2.7.4 _______________________________________________ ath10k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath10k
Quoted 8 lines · Balaji Pothunoori
For QCA988X target, pktlog gives details of the tx bitrate which is used in the driver for station info.
Enabling pktlog by default will cause more interrupts in target to host CE pipe, which can impact more CPU usage for targets ex:WCN3990 and also not required for all other platforms (eg: WCN3990), for getting tx bitrate.
Quoted 8 lines
Enable pktlog only for QCA988X based on hardware params.
Tested HW : WCN3990
Tested FW : WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1Fixes e8123bb74c4e ("ath10k: add per peer tx stats support for 10.2.4")Signed-off-by Balaji Pothunoori <[email protected]>Signed-off-by Kalle Valo <[email protected]>
Patch applied to ath-next branch of ath.git, thanks.
4fa42adebe5b ath10k: enabling tx stats support over pktlog
Signature · 3 lines
https://patchwork.kernel.org/patch/10941167/ https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
Quoted 8 lines · Balaji Pothunoori
For QCA988X target, pktlog gives details of the tx bitrate which is used in the driver for station info.
Enabling pktlog by default will cause more interrupts in target to host CE pipe, which can impact more CPU usage for targets ex:WCN3990 and also not required for all other platforms (eg: WCN3990), for getting tx bitrate.
Quoted 8 lines
Enable pktlog only for QCA988X based on hardware params.
Tested HW : WCN3990
Tested FW : WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1Fixes e8123bb74c4e ("ath10k: add per peer tx stats support for 10.2.4")Signed-off-by Balaji Pothunoori <[email protected]>Signed-off-by Kalle Valo <[email protected]>
Patch applied to ath-next branch of ath.git, thanks.
4fa42adebe5b ath10k: enabling tx stats support over pktlog
Signature · 9 lines
https://patchwork.kernel.org/patch/10941167/ https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches _______________________________________________ ath10k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath10k