net: ethernet: ti: Introduce am654 gigabit eth switch subsystem driver
Subsystems (2)
v6 cover net: ethernet: ti: Introduce am654 gigabit eth switch subsystem driver
Add new driver for the TI AM65x SoC Gigabit Ethernet Switch subsystem (CPSW NUSS). It has two ports and provides Ethernet packet communication for the device and can be configured as an Ethernet switch. CPSW NUSS features: the Reduced Gigabit Media Independent Interface (RGMII), Reduced Media Independent Interface (RMII), and the Management Data Input/Output (MDIO) interface for physical layer device (PHY) management. The TI AM65x SoC has integrated two-port Gigabit Ethernet Switch subsystem into device MCU domain named MCU_CPSW0. One Ethernet port (port 1) with selectable RGMII and RMII interfaces and an internal Communications Port Programming Interface (CPPI) port (Host port 0).
Host Port 0 CPPI Packet Streaming Interface interface supports 8 TX channels and on RX channels operating by TI am654 NAVSS Unified DMA Peripheral Root Complex (UDMA-P) controller.
Tested for tftp and booting to kernel on am654-evm.
Changes in v6:
* Fixed comments from Joe on the driver patch.
* Added Joe's Ack to the remaining patches.
* Removed Hexdump config.
Changes in v5:
* Rebased to latest which meant adapting to pinmux macro change.
Changes in v4:
* Patch1 caused dra7 config build warnings corrected them.
Grygorii Strashko (3):
arm64: dts: ti: k3-am65: add mcu cpsw node
arm64: dts: k3-am654-base-board: add mcu cpsw nuss pinmux and phy defs
configs: am65x_evm_a53: enable networking
Keerthy (2):
driver: net: ti: cpsw-mdio: use phys_addr_t for mdio_base addr
net: ethernet: ti: Introduce am654 gigabit eth switch subsystem
driver
arch/arm/dts/k3-am65.dtsi | 2 + arch/arm/dts/k3-am654-base-board-u-boot.dtsi | 170 ++++ configs/am65x_evm_a53_defconfig | 6 + drivers/net/ti/Kconfig | 8 + drivers/net/ti/Makefile | 1 + drivers/net/ti/am65-cpsw-nuss.c | 792 +++++++++++++++++++ drivers/net/ti/cpsw_mdio.c | 4 +- drivers/net/ti/cpsw_mdio.h | 2 +- 8 files changed, 982 insertions(+), 3 deletions(-) create mode 100644 drivers/net/ti/am65-cpsw-nuss.c
Signature · 1 line
2.17.1
PATCH v6 1/5 driver: net: ti: cpsw-mdio: use phys_addr_t for mdio_base addr
Use phys_addr_t for mdio_base address to avoid build warnings on arm64 and dra7. Cast it to uintprt_t before assigning to regs.
---
Changes in v6:
* Added Joe's Ack.
drivers/net/ti/cpsw_mdio.c | 4 ++-- drivers/net/ti/cpsw_mdio.h | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-)
drivers/net/ti/cpsw_mdio.c +2 -2
@@ -125,7 +125,7 @@ u32 cpsw_mdio_get_alive(struct mii_dev *bus)return val &GENMASK (15 ,0 ); } -struct mii_dev *cpsw_mdio_init (const char *name,u32 mdio_base, +struct mii_dev *cpsw_mdio_init (const char *name,phys_addr_t mdio_base,u32 bus_freq,int fck_freq) {struct cpsw_mdio *cpsw_mdio;
@@ -144,7 +144,7 @@ struct mii_dev *cpsw_mdio_init(const char *name, u32 mdio_base,return NULL ; } - cpsw_mdio->regs = (struct cpsw_mdio_regs *)mdio_base; + cpsw_mdio->regs = (struct cpsw_mdio_regs *)(uintptr_t )mdio_base;if (!bus_freq || !fck_freq) cpsw_mdio->div =CPSW_MDIO_DIV_DEF ;
drivers/net/ti/cpsw_mdio.h +1 -1
@@ -10,7 +10,7 @@struct cpsw_mdio ; -struct mii_dev *cpsw_mdio_init (const char *name,u32 mdio_base, +struct mii_dev *cpsw_mdio_init (const char *name,phys_addr_t mdio_base,u32 bus_freq,int fck_freq);void cpsw_mdio_free (struct mii_dev *bus);u32 cpsw_mdio_get_alive (struct mii_dev *bus);
Signature · 1 line
2.17.1
PATCH v6 1/5 driver: net: ti: cpsw-mdio: use phys_addr_t for mdio_base addr
Quoted 33 lines · Keerthy
Use
phys_addr_tformdio_baseaddress to avoid build warnings on arm64 and dra7. Cast it touintprt_tbefore assigning to regs.Signed-off-by Grygorii Strashko <[email protected]>Signed-off-by Keerthy <[email protected]>Reviewed-by Tom Rini <[email protected]>Acked-by Joe Hershberger <[email protected]>---
Changes in v6:
* Added Joe's Ack.
drivers/net/ti/cpsw_mdio.c | 4 ++-- drivers/net/ti/cpsw_mdio.h | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-)drivers/net/ti/cpsw_mdio.c +1
-1@@ -125,7 +125,7 @@ u32 cpsw_mdio_get_alive(struct mii_dev *bus)return val &GENMASK (15 ,0 ); } -struct mii_dev *cpsw_mdio_init (const char *name,u32 mdio_base, +struct mii_dev *cpsw_mdio_init (const char *name,phys_addr_t mdio_base,u32 bus_freq,int fck_freq) {struct cpsw_mdio *cpsw_mdio;
drivers/net/ti/cpsw_mdio.c struct mii_dev *cpsw_mdio_init(const char *name, u32 mdio_base, · line 148
Quoted 6 lines
drivers/net/ti/cpsw_mdio.c +1
-1@@ -144,7 +144,7 @@ struct mii_dev *cpsw_mdio_init(const char *name, u32 mdio_base,return NULL ; } - cpsw_mdio->regs = (struct cpsw_mdio_regs *)mdio_base; + cpsw_mdio->regs = (struct cpsw_mdio_regs *)(uintptr_t )mdio_base;
I'm missing something... the (uintptr_t) cast - is that a narrowing cast?
Signature · 1 line
Alex Kiernan
PATCH v6 1/5 driver: net: ti: cpsw-mdio: use phys_addr_t for mdio_base addr
Quoted 37 lines · Alex Kiernan
Quoted 36 lines · Keerthy
Use
phys_addr_tformdio_baseaddress to avoid build warnings on arm64 and dra7. Cast it touintprt_tbefore assigning to regs.Signed-off-by Grygorii Strashko <[email protected]>Signed-off-by Keerthy <[email protected]>Reviewed-by Tom Rini <[email protected]>Acked-by Joe Hershberger <[email protected]>---
Changes in v6:
* Added Joe's Ack.
drivers/net/ti/cpsw_mdio.c | 4 ++-- drivers/net/ti/cpsw_mdio.h | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-)drivers/net/ti/cpsw_mdio.c +1
-1@@ -125,7 +125,7 @@ u32 cpsw_mdio_get_alive(struct mii_dev *bus)return val &GENMASK (15 ,0 ); } -struct mii_dev *cpsw_mdio_init (const char *name,u32 mdio_base, +struct mii_dev *cpsw_mdio_init (const char *name,phys_addr_t mdio_base,u32 bus_freq,int fck_freq) {struct cpsw_mdio *cpsw_mdio;@@ -144,7 +144,7 @@ struct mii_dev *cpsw_mdio_init(const char *name, u32 mdio_base,return NULL ; }
Quoted 5 lines
drivers/net/ti/cpsw_mdio.c struct mii_dev *cpsw_mdio_init(const char *name, u32 mdio_base, · line 148
Quoted 3 lines
drivers/net/ti/cpsw_mdio.c +1
-1- cpsw_mdio->regs = (struct cpsw_mdio_regs *)mdio_base; + cpsw_mdio->regs = (struct cpsw_mdio_regs *)(uintptr_t )mdio_base;I'm missing something... the (
uintptr_t) cast - is that a narrowing cast?
Now the cpsw_mdio is used by both 32 bit and 64 bit SoCs. Hence uintptr_t cast helps obscure the type of a pointer.
Quoted 1 line
[U-Boot] driver: net: ti: cpsw-mdio: use phys_addr_t for mdio_base addr
In reply to KeerthyHi Keerthy,
https://patchwork.ozlabs.org/patch/1129505/ was applied to http://git.denx.de/?p=u-boot/u-boot-net.git
Thanks!
-Joe
PATCH v6 2/5 net: ethernet: ti: Introduce am654 gigabit eth switch subsystem driver
In reply to KeerthyAdd new driver for the TI AM65x SoC Gigabit Ethernet Switch subsystem (CPSW NUSS). It has two ports and provides Ethernet packet communication for the device and can be configured as an Ethernet switch. CPSW NUSS features: the Reduced Gigabit Media Independent Interface (RGMII), Reduced Media Independent Interface (RMII), and the Management Data Input/Output (MDIO) interface for physical layer device (PHY) management. The TI AM65x SoC has integrated two-port Gigabit Ethernet Switch subsystem into device MCU domain named MCU_CPSW0. One Ethernet port (port 1) with selectable RGMII and RMII interfaces and an internal Communications Port Programming Interface (CPPI) port (Host port 0).
Host Port 0 CPPI Packet Streaming Interface interface supports 8 TX channels and on RX channels operating by TI am654 NAVSS Unified DMA Peripheral Root Complex (UDMA-P) controller.
---
Changes in v6:
* Removed redundant #ifdef on DM_ETH
* Corrected a typo in dev_err.
drivers/net/ti/Kconfig | 8 + drivers/net/ti/Makefile | 1 + drivers/net/ti/am65-cpsw-nuss.c | 792 ++++++++++++++++++++++++++++++++ 3 files changed, 801 insertions(+) create mode 100644 drivers/net/ti/am65-cpsw-nuss.c
drivers/net/ti/Kconfig +8 -0
@@ -18,3 +18,11 @@ config DRIVER_TI_KEYSTONE_NET bool "TI Keystone 2 Ethernet" help This driver supports the TI Keystone 2 Ethernet subsystem + +config TI_AM65_CPSW_NUSS + bool "TI K3 AM65x MCU CPSW Nuss Ethernet controller driver" + depends on ARCH_K3 + select PHYLIB + help + This driver supports TI K3 MCU CPSW Nuss Ethernet controller + in Texas Instruments K3 AM65x SoCs.
drivers/net/ti/Makefile +1 -0
@@ -5,3 +5,4 @@ obj-$(CONFIG_DRIVER_TI_CPSW) += cpsw.o cpsw-common.o cpsw_mdio.o obj-$(CONFIG_DRIVER_TI_EMAC) += davinci_emac.o obj-$(CONFIG_DRIVER_TI_KEYSTONE_NET) += keystone_net.o cpsw_mdio.o +obj-$(CONFIG_TI_AM65_CPSW_NUSS) += am65-cpsw-nuss.o cpsw_mdio.o
drivers/net/ti/am65-cpsw-nuss.c new file +792 -0
792 lines not on this page · raw message
Signature · 1 line
2.17.1
PATCH v6 2/5 net: ethernet: ti: Introduce am654 gigabit eth switch subsystem driver
Quoted 12 lines · Keerthy
Add new driver for the TI AM65x SoC Gigabit Ethernet Switch subsystem (CPSW NUSS). It has two ports and provides Ethernet packet communication for the device and can be configured as an Ethernet switch. CPSW NUSS features: the Reduced Gigabit Media Independent Interface (RGMII), Reduced Media Independent Interface (RMII), and the Management Data Input/Output (MDIO) interface for physical layer device (PHY) management. The TI AM65x SoC has integrated two-port Gigabit Ethernet Switch subsystem into device MCU domain named
MCU_CPSW0. One Ethernet port (port 1) with selectable RGMII and RMII interfaces and an internal Communications Port Programming Interface (CPPI) port (Host port 0).
Quoted 6 lines
Host Port 0 CPPI Packet Streaming Interface interface supports 8 TX channels and on RX channels operating by TI am654 NAVSS Unified DMA Peripheral Root Complex (UDMA-P) controller.
Signed-off-by Grygorii Strashko <[email protected]>Signed-off-by Keerthy <[email protected]>
Hi Keerthy,
https://patchwork.ozlabs.org/patch/1129506/ was applied to http://git.denx.de/?p=u-boot/u-boot-net.git
Thanks!
-Joe
PATCH v6 3/5 arm64: dts: ti: k3-am65: add mcu cpsw node
In reply to KeerthyFrom: Grygorii Strashko <[email protected]>
Add mcu cpsw and its components along with scm_conf node to have ethernet functional.
---
Changes in v6:
* Added Joe's Ack.
arch/arm/dts/k3-am65.dtsi | 2 + arch/arm/dts/k3-am654-base-board-u-boot.dtsi | 111 +++++++++++++++++++ 2 files changed, 113 insertions(+)
arch/arm/dts/k3-am65.dtsi +2 -0
@@ -64,6 +64,7 @@ /* MCUSS Range */ <0x00 0x28380000 0x00 0x28380000 0x00 0x03880000>, <0x00 0x40200000 0x00 0x40200000 0x00 0x00900100>, + <0x00 0x40f00000 0x00 0x40f00000 0x00 0x00020000>, <0x00 0x42040000 0x00 0x42040000 0x00 0x03ac2400>, <0x00 0x45100000 0x00 0x45100000 0x00 0x00c24000>, <0x00 0x46000000 0x00 0x46000000 0x00 0x00200000>,
@@ -75,6 +76,7 @@ #size-cells = <2>; ranges = <0x00 0x28380000 0x00 0x28380000 0x00 0x03880000>, /* MCU NAVSS*/ <0x00 0x40200000 0x00 0x40200000 0x00 0x00900100>, /* First peripheral window */ + <0x00 0x40f00000 0x00 0x40f00000 0x00 0x00020000>, /* CTRL_MMR0 */ <0x00 0x42040000 0x00 0x42040000 0x00 0x03ac2400>, /* WKUP */ <0x00 0x45100000 0x00 0x45100000 0x00 0x00c24000>, /* MMRs, remaining NAVSS */ <0x00 0x46000000 0x00 0x46000000 0x00 0x00200000>, /* CPSW */
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +111 -0
123 lines not on this page · raw message
Signature · 1 line
2.17.1
[U-Boot] arm64: dts: ti: k3-am65: add mcu cpsw node
Hi Keerthy,
https://patchwork.ozlabs.org/patch/1129509/ was applied to http://git.denx.de/?p=u-boot/u-boot-net.git
Thanks!
-Joe
PATCH v6 4/5 arm64: dts: k3-am654-base-board: add mcu cpsw nuss pinmux and phy defs
In reply to KeerthyFrom: Grygorii Strashko <[email protected]>
Add mcu cpsw nuss pinmux and phy defs required by cpsw.
---
Changes in v6:
* Added Joe's Ack.
arch/arm/dts/k3-am654-base-board-u-boot.dtsi | 59 ++++++++++++++++++++ 1 file changed, 59 insertions(+)
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +59 -0
@@ -5,6 +5,7 @@ #include <dt-bindings/pinctrl/k3.h> #include <dt-bindings/dma/k3-udma.h> +#include <dt-bindings/net/ti-dp83867.h> / { chosen {
@@ -300,6 +301,32 @@ u-boot,dm-spl; }; +&wkup_pmx0 { + mcu_cpsw_pins_default: mcu_cpsw_pins_default { + pinctrl-single,pins = < + AM65X_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* (N4) MCU_RGMII1_TX_CTL */ + AM65X_WKUP_IOPAD(0x005c, PIN_INPUT, 0) /* (N5) MCU_RGMII1_RX_CTL */ + AM65X_WKUP_IOPAD(0x0060, PIN_OUTPUT, 0) /* (M2) MCU_RGMII1_TD3 */ + AM65X_WKUP_IOPAD(0x0064, PIN_OUTPUT, 0) /* (M3) MCU_RGMII1_TD2 */ + AM65X_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* (M4) MCU_RGMII1_TD1 */ + AM65X_WKUP_IOPAD(0x006c, PIN_OUTPUT, 0) /* (M5) MCU_RGMII1_TD0 */ + AM65X_WKUP_IOPAD(0x0078, PIN_INPUT, 0) /* (L2) MCU_RGMII1_RD3 */ + AM65X_WKUP_IOPAD(0x007c, PIN_INPUT, 0) /* (L5) MCU_RGMII1_RD2 */ + AM65X_WKUP_IOPAD(0x0080, PIN_INPUT, 0) /* (M6) MCU_RGMII1_RD1 */ + AM65X_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* (L6) MCU_RGMII1_RD0 */ + AM65X_WKUP_IOPAD(0x0070, PIN_INPUT, 0) /* (N1) MCU_RGMII1_TXC */ + AM65X_WKUP_IOPAD(0x0074, PIN_INPUT, 0) /* (M1) MCU_RGMII1_RXC */ + >; + }; + + mcu_mdio_pins_default: mcu_mdio1_pins_default { + pinctrl-single,pins = < + AM65X_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */ + AM65X_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */ + >; + }; +}; + &main_uart0 { u-boot,dm-spl; pinctrl-names = "default";
@@ -323,3 +350,35 @@ pinctrl-0 = <&main_mmc1_pins_default>; sdhci-caps-mask = <0x7 0x0>; }; + +&mcu_cpsw { + pinctrl-names = "default"; + pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>; +}; + +&davinci_mdio { + phy0: ethernet-phy at 0 { + reg = <0>; + /* TODO: phy reset: TCA9555RTWR(i2c:0x21)[p04].GPIO_MCU_RGMII_RSTN */ + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + }; +}; + +&cpsw_port1 { + phy-mode = "rgmii-id"; + phy-handle = <&phy0>; +}; + +&mcu_cpsw { + reg = <0x0 0x46000000 0x0 0x200000>, + <0x0 0x40f00200 0x0 0x2>; + reg-names = "cpsw_nuss", "mac_efuse"; + + cpsw-phy-sel at 40f04040 { + compatible = "ti,am654-cpsw-phy-sel"; + reg= <0x0 0x40f04040 0x0 0x4>; + reg-names = "gmii-sel"; + }; +};
Signature · 1 line
2.17.1
[U-Boot] arm64: dts: k3-am654-base-board: add mcu cpsw nuss pinmux and phy defs
Hi Keerthy,
https://patchwork.ozlabs.org/patch/1129508/ was applied to http://git.denx.de/?p=u-boot/u-boot-net.git
Thanks!
-Joe
PATCH v6 5/5 configs: am65x_evm_a53: enable networking
In reply to KeerthyFrom: Grygorii Strashko <[email protected]>
Enable TI K3 AM65x CPSW NUSS driver.
---
Changes in v6:
* Removed unused HEXDUMP config.
* Added Joe's Ack.
configs/am65x_evm_a53_defconfig | 6 ++++++ 1 file changed, 6 insertions(+)
configs/am65x_evm_a53_defconfig +6 -0
@@ -44,6 +44,7 @@ CONFIG_SPL_MULTI_DTB_FIT_NO_COMPRESSION=y CONFIG_ENV_IS_IN_FAT=y CONFIG_ENV_FAT_INTERFACE="mmc" CONFIG_ENV_FAT_DEVICE_AND_PART="1:1" +CONFIG_NET_RANDOM_ETHADDR=y CONFIG_DM=y CONFIG_SPL_DM=y CONFIG_SPL_DM_SEQ_ALIAS=y
@@ -58,6 +59,11 @@ CONFIG_K3_SEC_PROXY=y CONFIG_DM_MMC=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_K3_ARASAN=y +CONFIG_PHY_TI=y +CONFIG_PHY_FIXED=y +CONFIG_DM_ETH=y +CONFIG_TI_AM65_CPSW_NUSS=y +CONFIG_PHY=y CONFIG_PINCTRL=y # CONFIG_PINCTRL_GENERIC is not set CONFIG_SPL_PINCTRL=y
Signature · 1 line
2.17.1
PATCH v6 5/5 configs: am65x_evm_a53: enable networking
Quoted 23 lines · Keerthy
From: Grygorii Strashko <[email protected]>
Enable TI K3 AM65x CPSW NUSS driver.
Signed-off-by Grygorii Strashko <[email protected]>Signed-off-by Keerthy <[email protected]>Reviewed-by Tom Rini <[email protected]>Acked-by Joe Hershberger <[email protected]>---
Changes in v6:
* Removed unused HEXDUMP config.
* Added Joe's Ack.configs/am65x_evm_a53_defconfig | 6 ++++++ 1 file changed, 6 insertions(+)configs/am65x_evm_a53_defconfig +0
-0
configs/am65x_evm_a53_defconfig CONFIG_SPL_MULTI_DTB_FIT_NO_COMPRESSION=y · line 47
Quoted 4 lines
configs/am65x_evm_a53_defconfig +1
-0@@ -44,6 +44,7 @@ CONFIG_SPL_MULTI_DTB_FIT_NO_COMPRESSION=y CONFIG_ENV_IS_IN_FAT=y CONFIG_ENV_FAT_INTERFACE="mmc" CONFIG_ENV_FAT_DEVICE_AND_PART="1:1" +CONFIG_NET_RANDOM_ETHADDR=y
Do we really need this?
Thanks and regards,
Lokesh
Quoted 16 lines
configs/am65x_evm_a53_defconfig +5
-0CONFIG_DM=y CONFIG_SPL_DM=y CONFIG_SPL_DM_SEQ_ALIAS=y@@ -58,6 +59,11 @@ CONFIG_K3_SEC_PROXY=y CONFIG_DM_MMC=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_K3_ARASAN=y +CONFIG_PHY_TI=y +CONFIG_PHY_FIXED=y +CONFIG_DM_ETH=y +CONFIG_TI_AM65_CPSW_NUSS=y +CONFIG_PHY=y CONFIG_PINCTRL=y # CONFIG_PINCTRL_GENERIC is not set CONFIG_SPL_PINCTRL=y
PATCH v6 5/5 configs: am65x_evm_a53: enable networking
Quoted 21 lines · Lokesh Vutla
Quoted 18 lines · Keerthy
From: Grygorii Strashko <[email protected]>
Enable TI K3 AM65x CPSW NUSS driver.
Signed-off-by Grygorii Strashko <[email protected]>Signed-off-by Keerthy <[email protected]>Reviewed-by Tom Rini <[email protected]>Acked-by Joe Hershberger <[email protected]>---
Changes in v6:
* Removed unused HEXDUMP config.
* Added Joe's Ack.configs/am65x_evm_a53_defconfig | 6 ++++++ 1 file changed, 6 insertions(+)
Quoted 9 lines
configs/am65x_evm_a53_defconfig CONFIG_SPL_MULTI_DTB_FIT_NO_COMPRESSION=y · line 47
Quoted 9 lines
configs/am65x_evm_a53_defconfig +1
-0@@ -44,6 +44,7 @@ CONFIG_SPL_MULTI_DTB_FIT_NO_COMPRESSION=y CONFIG_ENV_IS_IN_FAT=y CONFIG_ENV_FAT_INTERFACE="mmc" CONFIG_ENV_FAT_DEVICE_AND_PART="1:1" +CONFIG_NET_RANDOM_ETHADDR=y
Fallback option in case efuse MAC ID read fails for some reason.
Quoted 23 lines
Do we really need this?
Thanks and regards,
LokeshQuoted 16 lines
configs/am65x_evm_a53_defconfig +5
-0CONFIG_DM=y CONFIG_SPL_DM=y CONFIG_SPL_DM_SEQ_ALIAS=y@@ -58,6 +59,11 @@ CONFIG_K3_SEC_PROXY=y CONFIG_DM_MMC=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_K3_ARASAN=y +CONFIG_PHY_TI=y +CONFIG_PHY_FIXED=y +CONFIG_DM_ETH=y +CONFIG_TI_AM65_CPSW_NUSS=y +CONFIG_PHY=y CONFIG_PINCTRL=y # CONFIG_PINCTRL_GENERIC is not set CONFIG_SPL_PINCTRL=y
PATCH v6 5/5 configs: am65x_evm_a53: enable networking
Quoted 24 lines · Keerthy
Quoted 21 lines · Lokesh Vutla
Quoted 18 lines · Keerthy
From: Grygorii Strashko <[email protected]>
Enable TI K3 AM65x CPSW NUSS driver.
Signed-off-by Grygorii Strashko <[email protected]>Signed-off-by Keerthy <[email protected]>Reviewed-by Tom Rini <[email protected]>Acked-by Joe Hershberger <[email protected]>---
Changes in v6:
* Removed unused HEXDUMP config.
* Added Joe's Ack.configs/am65x_evm_a53_defconfig | 6 ++++++
1 file changed, 6 insertions(+)
Quoted 11 lines
Quoted 9 lines
Quoted 9 lines
configs/am65x_evm_a53_defconfig +0
-0@@ -44,6 +44,7 @@ CONFIG_SPL_MULTI_DTB_FIT_NO_COMPRESSION=y
CONFIG_ENV_IS_IN_FAT=y
CONFIG_ENV_FAT_INTERFACE="mmc"
CONFIG_ENV_FAT_DEVICE_AND_PART="1:1"
+CONFIG_NET_RANDOM_ETHADDR=yFallback option in case efuse MAC ID read fails for some reason.
Ahh I forgot that this is a fallback option.
Thanks and regards,
Lokesh
Quoted 24 lines
Quoted 24 lines
Do we really need this?
Thanks and regards,
LokeshQuoted 16 lines
CONFIG_DM=y
CONFIG_SPL_DM=y
CONFIG_SPL_DM_SEQ_ALIAS=yconfigs/am65x_evm_a53_defconfig +0
-0@@ -58,6 +59,11 @@ CONFIG_K3_SEC_PROXY=y
CONFIG_DM_MMC=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_K3_ARASAN=yconfigs/am65x_evm_a53_defconfig +5
-0+CONFIG_PHY_TI=y +CONFIG_PHY_FIXED=y +CONFIG_DM_ETH=y +CONFIG_TI_AM65_CPSW_NUSS=y +CONFIG_PHY=y
CONFIG_PINCTRL=y
#CONFIG_PINCTRL_GENERICis not set
CONFIG_SPL_PINCTRL=y
[U-Boot] configs: am65x_evm_a53: enable networking
In reply to KeerthyHi Keerthy,
https://patchwork.ozlabs.org/patch/1129507/ was applied to http://git.denx.de/?p=u-boot/u-boot-net.git
Thanks!
-Joe