board/freescale: Introduce UBOOTBIN in spl template
PATCH 1/2 board/freescale: Introduce UBOOTBIN in spl template
For board like imx7d-pico u-boot.img change to u-boot-dtb.img in U-Boot v2019.07 so replace hard code u-boot.img with variable
--- .../common/imx/genimage.cfg.template_no_boot_part_spl | 4 ++-- board/freescale/common/imx/genimage.cfg.template_spl | 4 ++-- board/freescale/common/imx/post-image.sh | 4 ++++ 3 files changed, 8 insertions(+), 4 deletions(-)
board/freescale/common/imx/genimage.cfg.template_no_boot_part_spl +2 -2
@@ -17,9 +17,9 @@ image sdcard.img { offset = 1024 } - partition u-boot-img { + partition u-boot { in-partition-table = "no" - image = "u-boot.img" + image = "%UBOOTBIN%" offset = 69K }
board/freescale/common/imx/genimage.cfg.template_spl +2 -2
@@ -26,9 +26,9 @@ image sdcard.img { offset = 1024 } - partition u-boot-img { + partition u-boot { in-partition-table = "no" - image = "u-boot.img" + image = "%UBOOTBIN%" offset = 69K }
board/freescale/common/imx/post-image.sh +4 -0
@@ -66,6 +66,10 @@ uboot_image() echo "u-boot-dtb.imx" elif grep -Eq "^BR2_TARGET_UBOOT_FORMAT_IMX=y$" ${BR2_CONFIG}; then echo "u-boot.imx" + elif grep -Eq "^BR2_TARGET_UBOOT_FORMAT_DTB_IMG=y$" ${BR2_CONFIG}; then + echo "u-boot-dtb.img" + elif grep -Eq "^BR2_TARGET_UBOOT_FORMAT_DTB_IMG=y$" ${BR2_CONFIG}; then + echo "u-boot.img" fi }
Signature · 1 line
2.17.1
PATCH 2/2 configs/imx7dpico: Bump U-Boot to 2019.07 and kernel to version 5.1.16.
Also
- adjust the U-Boot binary name after DM conversion.
- add missing notes about flashing U-Boot and SPL
--- board/technexion/imx7dpico/readme.txt | 55 ++++++++++++++++++++++++++- configs/imx7dpico_defconfig | 6 +-- 2 files changed, 57 insertions(+), 4 deletions(-)
board/technexion/imx7dpico/readme.txt +54 -1
@@ -20,10 +20,63 @@ You will find in output/images/ the following files: - rootfs.ext4 - rootfs.tar - sdcard.img - - u-boot.img + - u-boot-dtb.img - SPL - zImage +Flash U-Boot and SPL +===== + +Note: This method is convenient for development purposes. +If the eMMC has already a U-Boot flashed with DFU support then +the user can go to step 2 below in order to update U-Boot. + +Put pico board in USB download mode (refer to the PICO-iMX7D Quick Start Guide +page 3) + +Connect a USB to serial adapter between the host PC and pico. + +Connect a USB cable between the OTG pico port and the host PC. + +Note: Some computers may be a bit strict with USB current draw and will +shut down their ports if the draw is too high. The solution for that is +to use an externally powered USB hub between the board and the host computer. + +Open a terminal program such as minicom. + +Copy SPL and u-boot-dtb.img to the imx_usb_loader folder. + +Load the SPL binary via USB: + +$ sudo ./imx_usb SPL + +Load the u-boot-dtb.img binary via USB: + +$ sudo ./imx_usb u-boot-dtb.img + +Then U-Boot starts and its messages appear in the console program. + +Use the default environment variables: + +=> env default -f -a +=> saveenv + +Run the DFU agent so we can flash the new images using dfu-util tool: + +=> dfu 0 mmc 0 + +Flash SPL and u-boot-dtb.img into the eMMC running the following commands on a PC: + +$ sudo dfu-util -D SPL -a spl + +$ sudo dfu-util -D u-boot-dtb.img -a u-boot + +Remove power from the pico board. + +Put pico board into normal boot mode. + +Power up the board and the new updated U-Boot should boot from eMMC. + Flash the eMMC ==============
configs/imx7dpico_defconfig +3 -3
@@ -12,7 +12,7 @@ BR2_TARGET_GENERIC_GETTY_PORT="ttymxc4" # kernel BR2_LINUX_KERNEL=y BR2_LINUX_KERNEL_CUSTOM_VERSION=y -BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.1.6" +BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.1.16" BR2_LINUX_KERNEL_DEFCONFIG="imx_v6_v7" BR2_LINUX_KERNEL_DTS_SUPPORT=y BR2_LINUX_KERNEL_INTREE_DTS_NAME="imx7d-pico-pi"
@@ -25,8 +25,8 @@ BR2_TARGET_UBOOT_SPL=y BR2_TARGET_UBOOT_SPL_NAME="SPL" BR2_TARGET_UBOOT_BOARDNAME="pico-pi-imx7d" BR2_TARGET_UBOOT_CUSTOM_VERSION=y -BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2019.01" -BR2_TARGET_UBOOT_FORMAT_IMG=y +BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2019.07" +BR2_TARGET_UBOOT_FORMAT_DTB_IMG=y # wifi firmware for brcm43439 BR2_PACKAGE_LINUX_FIRMWARE=y
Signature · 1 line
2.17.1
PATCH 2/2 configs/imx7dpico: Bump U-Boot to 2019.07 and kernel to version 5.1.16.
Quoted 15 lines · Joris Offouga
Also
- adjust the U-Boot binary name after DM conversion.
- add missing notes about flashing U-Boot and SPLSigned-off-by Joris Offouga <[email protected]>--- board/technexion/imx7dpico/readme.txt | 55 ++++++++++++++++++++++++++- configs/imx7dpico_defconfig | 6 +-- 2 files changed, 57 insertions(+), 4 deletions(-)board/technexion/imx7dpico/readme.txt +0
-0
board/technexion/imx7dpico/readme.txt You will find in output/images/ the following files: · line 28
Quoted 10 lines
board/technexion/imx7dpico/readme.txt +3
-1@@ -20,10 +20,63 @@ You will find in output/images/ the following files: - rootfs.ext4 - rootfs.tar - sdcard.img - - u-boot.img + - u-boot-dtb.img - SPL - zImage +Flash U-Boot and SPL +=====
It would have been nice to add this as a separate patch, before the bump.
However, I guess it needs heavy modification in that case, so I applied to
master as-is after all, thanks.
Regards,
Arnout
Quoted 79 lines
board/technexion/imx7dpico/readme.txt +51
-0+ +Note: This method is convenient for development purposes. +If the eMMC has already a U-Boot flashed with DFU support then +the user can go to step 2 below in order to update U-Boot. + +Put pico board in USB download mode (refer to the PICO-iMX7D Quick Start Guide +page 3) + +Connect a USB to serial adapter between the host PC and pico. + +Connect a USB cable between the OTG pico port and the host PC. + +Note: Some computers may be a bit strict with USB current draw and will +shut down their ports if the draw is too high. The solution for that is +to use an externally powered USB hub between the board and the host computer. + +Open a terminal program such as minicom. + +Copy SPL and u-boot-dtb.img to the imx_usb_loader folder. + +Load the SPL binary via USB: + +$ sudo ./imx_usb SPL + +Load the u-boot-dtb.img binary via USB: + +$ sudo ./imx_usb u-boot-dtb.img + +Then U-Boot starts and its messages appear in the console program. + +Use the default environment variables: + +=> env default -f -a +=> saveenv + +Run the DFU agent so we can flash the new images using dfu-util tool: + +=> dfu 0 mmc 0 + +Flash SPL and u-boot-dtb.img into the eMMC running the following commands on a PC: + +$ sudo dfu-util -D SPL -a spl + +$ sudo dfu-util -D u-boot-dtb.img -a u-boot + +Remove power from the pico board. + +Put pico board into normal boot mode. + +Power up the board and the new updated U-Boot should boot from eMMC. + Flash the eMMC ==============configs/imx7dpico_defconfig +3
-3@@ -12,7 +12,7 @@ BR2_TARGET_GENERIC_GETTY_PORT="ttymxc4" # kernel BR2_LINUX_KERNEL=y BR2_LINUX_KERNEL_CUSTOM_VERSION=y -BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.1.6" +BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.1.16" BR2_LINUX_KERNEL_DEFCONFIG="imx_v6_v7" BR2_LINUX_KERNEL_DTS_SUPPORT=y BR2_LINUX_KERNEL_INTREE_DTS_NAME="imx7d-pico-pi"@@ -25,8 +25,8 @@ BR2_TARGET_UBOOT_SPL=y BR2_TARGET_UBOOT_SPL_NAME="SPL" BR2_TARGET_UBOOT_BOARDNAME="pico-pi-imx7d" BR2_TARGET_UBOOT_CUSTOM_VERSION=y -BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2019.01" -BR2_TARGET_UBOOT_FORMAT_IMG=y +BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2019.07" +BR2_TARGET_UBOOT_FORMAT_DTB_IMG=y # wifi firmware for brcm43439 BR2_PACKAGE_LINUX_FIRMWARE=y
Arnout Vandecappelle
AppliedPATCH 1/2 board/freescale: Introduce UBOOTBIN in spl template
In reply to Joris OffougaQuoted 47 lines · Joris Offouga
For board like imx7d-pico u-boot.img change to u-boot-dtb.img in U-Boot v2019.07 so replace hard code u-boot.img with variable
Signed-off-by Joris Offouga <[email protected]>--- .../common/imx/genimage.cfg.template_no_boot_part_spl | 4 ++-- board/freescale/common/imx/genimage.cfg.template_spl | 4 ++-- board/freescale/common/imx/post-image.sh | 4 ++++ 3 files changed, 8 insertions(+), 4 deletions(-)board/freescale/common/imx/genimage.cfg.template_no_boot_part_spl +2
-2@@ -17,9 +17,9 @@ image sdcard.img { offset = 1024 } - partition u-boot-img { + partition u-boot { in-partition-table = "no" - image = "u-boot.img" + image = "%UBOOTBIN%" offset = 69K }board/freescale/common/imx/genimage.cfg.template_spl +2
-2@@ -26,9 +26,9 @@ image sdcard.img { offset = 1024 } - partition u-boot-img { + partition u-boot { in-partition-table = "no" - image = "u-boot.img" + image = "%UBOOTBIN%" offset = 69K }board/freescale/common/imx/post-image.sh +0
-0
board/freescale/common/imx/post-image.sh uboot_image() · line 71
Quoted 6 lines
board/freescale/common/imx/post-image.sh +3
-0@@ -66,6 +66,10 @@ uboot_image() echo "u-boot-dtb.imx" elif grep -Eq "^BR2_TARGET_UBOOT_FORMAT_IMX=y$" ${BR2_CONFIG}; then echo "u-boot.imx" + elif grep -Eq "^BR2_TARGET_UBOOT_FORMAT_DTB_IMG=y$" ${BR2_CONFIG}; then + echo "u-boot-dtb.img" + elif grep -Eq "^BR2_TARGET_UBOOT_FORMAT_DTB_IMG=y$" ${BR2_CONFIG}; then
This should have been BR2_TARGET_UBOOT_FORMAT_IMG.
Applied to master with that fixed, and with a heavily reworked commit log, thanks.
Regards,
Arnout
Quoted 5 lines
board/freescale/common/imx/post-image.sh +1
-0+ echo "u-boot.img" fi }
PATCH 1/2 board/freescale: Introduce UBOOTBIN in spl template
Le 09/07/2019 ? 20:06, Arnout Vandecappelle a ?crit?:
Quoted 44 lines · Joris Offouga
Quoted 42 lines
For board like imx7d-pico u-boot.img change to u-boot-dtb.img in U-Boot v2019.07 so replace hard code u-boot.img with variable
Signed-off-by Joris Offouga <[email protected]>--- .../common/imx/genimage.cfg.template_no_boot_part_spl | 4 ++-- board/freescale/common/imx/genimage.cfg.template_spl | 4 ++-- board/freescale/common/imx/post-image.sh | 4 ++++ 3 files changed, 8 insertions(+), 4 deletions(-)board/freescale/common/imx/genimage.cfg.template_no_boot_part_spl +2
-2@@ -17,9 +17,9 @@ image sdcard.img { offset = 1024 } - partition u-boot-img { + partition u-boot { in-partition-table = "no" - image = "u-boot.img" + image = "%UBOOTBIN%" offset = 69K }board/freescale/common/imx/genimage.cfg.template_spl +2
-2@@ -26,9 +26,9 @@ image sdcard.img { offset = 1024 } - partition u-boot-img { + partition u-boot { in-partition-table = "no" - image = "u-boot.img" + image = "%UBOOTBIN%" offset = 69K }
Quoted 12 lines
board/freescale/common/imx/post-image.sh uboot_image() · line 71
Quoted 11 lines
board/freescale/common/imx/post-image.sh +3
-0@@ -66,6 +66,10 @@ uboot_image() echo "u-boot-dtb.imx" elif grep -Eq "^BR2_TARGET_UBOOT_FORMAT_IMX=y$" ${BR2_CONFIG}; then echo "u-boot.imx" + elif grep -Eq "^BR2_TARGET_UBOOT_FORMAT_DTB_IMG=y$" ${BR2_CONFIG}; then + echo "u-boot-dtb.img" + elif grep -Eq "^BR2_TARGET_UBOOT_FORMAT_DTB_IMG=y$" ${BR2_CONFIG}; thenThis should have been
BR2_TARGET_UBOOT_FORMAT_IMG.
Indeed, i use wrong config, i send new patch for fix this:
Also for U-Boot 2019.07, it is necessary to apply the series of Pierre-Jean
Best Regards,
Joris Offouga
Quoted 11 lines
Applied to master with that fixed, and with a heavily reworked commit log, thanks.
Regards,
ArnoutQuoted 5 lines
board/freescale/common/imx/post-image.sh +1
-0+ echo "u-boot.img" fi }