Skip to contentSkip to conversation

board/freescale: Introduce UBOOTBIN in spl template

PATCH New Joris Offouga 2 participants 5 messages Jul 9, 2019 Arm i.MX and Layerscape

lore
Share & tools
lore
#0 lore raw

PATCH 1/2 board/freescale: Introduce UBOOTBIN in spl template

For board like imx7d-pico u-boot.img change to u-boot-dtb.img in U-Boot v2019.07 so replace hard code u-boot.img with variable

---
 .../common/imx/genimage.cfg.template_no_boot_part_spl         | 4 ++--
 board/freescale/common/imx/genimage.cfg.template_spl          | 4 ++--
 board/freescale/common/imx/post-image.sh                      | 4 ++++
 3 files changed, 8 insertions(+), 4 deletions(-)
board/freescale/common/imx/genimage.cfg.template_no_boot_part_spl +2 -2
index 9cdecc6ce0..c29032572a 100644
@@ -17,9 +17,9 @@ image sdcard.img {
     offset = 1024
   }
 
-  partition u-boot-img {
+  partition u-boot {
     in-partition-table = "no"
-    image = "u-boot.img"
+    image = "%UBOOTBIN%"
     offset = 69K
   }
 
board/freescale/common/imx/genimage.cfg.template_spl +2 -2
index 0b6e22864b..d2d810777b 100644
@@ -26,9 +26,9 @@ image sdcard.img {
     offset = 1024
   }
 
-  partition u-boot-img {
+  partition u-boot {
     in-partition-table = "no"
-    image = "u-boot.img"
+    image = "%UBOOTBIN%"
     offset = 69K
   }
 
board/freescale/common/imx/post-image.sh +4 -0
index 12756c63d5..ab51dc2098 100755
@@ -66,6 +66,10 @@ uboot_image()
 		echo "u-boot-dtb.imx"
 	elif grep -Eq "^BR2_TARGET_UBOOT_FORMAT_IMX=y$" ${BR2_CONFIG}; then
 		echo "u-boot.imx"
+	elif grep -Eq "^BR2_TARGET_UBOOT_FORMAT_DTB_IMG=y$" ${BR2_CONFIG}; then
+	    echo "u-boot-dtb.img"
+	elif grep -Eq "^BR2_TARGET_UBOOT_FORMAT_DTB_IMG=y$" ${BR2_CONFIG}; then
+	    echo "u-boot.img"
 	fi
 }
 
Signature · 1 line
2.17.1
#1 lore raw

PATCH 2/2 configs/imx7dpico: Bump U-Boot to 2019.07 and kernel to version 5.1.16.

Also
- adjust the U-Boot binary name after DM conversion.
- add missing notes about flashing U-Boot and SPL

---
 board/technexion/imx7dpico/readme.txt | 55 ++++++++++++++++++++++++++-
 configs/imx7dpico_defconfig           |  6 +--
 2 files changed, 57 insertions(+), 4 deletions(-)
board/technexion/imx7dpico/readme.txt +54 -1
index 1b9e80a0fd..53197d458d 100644
@@ -20,10 +20,63 @@ You will find in output/images/ the following files:
   - rootfs.ext4
   - rootfs.tar
   - sdcard.img
-  - u-boot.img
+  - u-boot-dtb.img
   - SPL
   - zImage
 
+Flash U-Boot and SPL
+=====
+
+Note: This method is convenient for development purposes.
+If the eMMC has already a U-Boot flashed with DFU support then
+the user can go to step 2 below in order to update U-Boot.
+
+Put pico board in USB download mode (refer to the PICO-iMX7D Quick Start Guide
+page 3)
+
+Connect a USB to serial adapter between the host PC and pico.
+
+Connect a USB cable between the OTG pico port and the host PC.
+
+Note: Some computers may be a bit strict with USB current draw and will
+shut down their ports if the draw is too high. The solution for that is
+to use an externally powered USB hub between the board and the host computer.
+
+Open a terminal program such as minicom.
+
+Copy SPL and u-boot-dtb.img to the imx_usb_loader folder.
+
+Load the SPL binary via USB:
+
+$ sudo ./imx_usb SPL
+
+Load the u-boot-dtb.img binary via USB:
+
+$ sudo ./imx_usb u-boot-dtb.img
+
+Then U-Boot starts and its messages appear in the console program.
+
+Use the default environment variables:
+
+=> env default -f -a
+=> saveenv
+
+Run the DFU agent so we can flash the new images using dfu-util tool:
+
+=> dfu 0 mmc 0
+
+Flash SPL and u-boot-dtb.img into the eMMC running the following commands on a PC:
+
+$ sudo dfu-util -D SPL -a spl
+
+$ sudo dfu-util -D u-boot-dtb.img -a u-boot
+
+Remove power from the pico board.
+
+Put pico board into normal boot mode.
+
+Power up the board and the new updated U-Boot should boot from eMMC.
+
 Flash the eMMC
 ==============
 
configs/imx7dpico_defconfig +3 -3
index a5d41657f1..151b7fd65a 100644
@@ -12,7 +12,7 @@ BR2_TARGET_GENERIC_GETTY_PORT="ttymxc4"
 # kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.1.6"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.1.16"
 BR2_LINUX_KERNEL_DEFCONFIG="imx_v6_v7"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="imx7d-pico-pi"
@@ -25,8 +25,8 @@ BR2_TARGET_UBOOT_SPL=y
 BR2_TARGET_UBOOT_SPL_NAME="SPL"
 BR2_TARGET_UBOOT_BOARDNAME="pico-pi-imx7d"
 BR2_TARGET_UBOOT_CUSTOM_VERSION=y
-BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2019.01"
-BR2_TARGET_UBOOT_FORMAT_IMG=y
+BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2019.07"
+BR2_TARGET_UBOOT_FORMAT_DTB_IMG=y
 
 # wifi firmware for brcm43439
 BR2_PACKAGE_LINUX_FIRMWARE=y
Signature · 1 line
2.17.1
#2 lore raw

PATCH 2/2 configs/imx7dpico: Bump U-Boot to 2019.07 and kernel to version 5.1.16.

Quoted 15 lines · Joris Offouga

Also
- adjust the U-Boot binary name after DM conversion.
- add missing notes about flashing U-Boot and SPL

---
 board/technexion/imx7dpico/readme.txt | 55 ++++++++++++++++++++++++++-
 configs/imx7dpico_defconfig           |  6 +--
 2 files changed, 57 insertions(+), 4 deletions(-)
board/technexion/imx7dpico/readme.txt +0 -0
index 1b9e80a0fd..53197d458d 100644

board/technexion/imx7dpico/readme.txt You will find in output/images/ the following files: · line 28

Quoted 10 lines
board/technexion/imx7dpico/readme.txt +3 -1
@@ -20,10 +20,63 @@ You will find in output/images/ the following files:
   - rootfs.ext4
   - rootfs.tar
   - sdcard.img
-  - u-boot.img
+  - u-boot-dtb.img
   - SPL
   - zImage
 
+Flash U-Boot and SPL
+=====

It would have been nice to add this as a separate patch, before the bump.

However, I guess it needs heavy modification in that case, so I applied to
master as-is after all, thanks.

Regards,
Arnout

Quoted 79 lines
board/technexion/imx7dpico/readme.txt +51 -0
+
+Note: This method is convenient for development purposes.
+If the eMMC has already a U-Boot flashed with DFU support then
+the user can go to step 2 below in order to update U-Boot.
+
+Put pico board in USB download mode (refer to the PICO-iMX7D Quick Start Guide
+page 3)
+
+Connect a USB to serial adapter between the host PC and pico.
+
+Connect a USB cable between the OTG pico port and the host PC.
+
+Note: Some computers may be a bit strict with USB current draw and will
+shut down their ports if the draw is too high. The solution for that is
+to use an externally powered USB hub between the board and the host computer.
+
+Open a terminal program such as minicom.
+
+Copy SPL and u-boot-dtb.img to the imx_usb_loader folder.
+
+Load the SPL binary via USB:
+
+$ sudo ./imx_usb SPL
+
+Load the u-boot-dtb.img binary via USB:
+
+$ sudo ./imx_usb u-boot-dtb.img
+
+Then U-Boot starts and its messages appear in the console program.
+
+Use the default environment variables:
+
+=> env default -f -a
+=> saveenv
+
+Run the DFU agent so we can flash the new images using dfu-util tool:
+
+=> dfu 0 mmc 0
+
+Flash SPL and u-boot-dtb.img into the eMMC running the following commands on a PC:
+
+$ sudo dfu-util -D SPL -a spl
+
+$ sudo dfu-util -D u-boot-dtb.img -a u-boot
+
+Remove power from the pico board.
+
+Put pico board into normal boot mode.
+
+Power up the board and the new updated U-Boot should boot from eMMC.
+
 Flash the eMMC
 ==============
 
configs/imx7dpico_defconfig +3 -3
index a5d41657f1..151b7fd65a 100644
@@ -12,7 +12,7 @@ BR2_TARGET_GENERIC_GETTY_PORT="ttymxc4"
 # kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.1.6"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.1.16"
 BR2_LINUX_KERNEL_DEFCONFIG="imx_v6_v7"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="imx7d-pico-pi"
@@ -25,8 +25,8 @@ BR2_TARGET_UBOOT_SPL=y
 BR2_TARGET_UBOOT_SPL_NAME="SPL"
 BR2_TARGET_UBOOT_BOARDNAME="pico-pi-imx7d"
 BR2_TARGET_UBOOT_CUSTOM_VERSION=y
-BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2019.01"
-BR2_TARGET_UBOOT_FORMAT_IMG=y
+BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2019.07"
+BR2_TARGET_UBOOT_FORMAT_DTB_IMG=y
 
 # wifi firmware for brcm43439
 BR2_PACKAGE_LINUX_FIRMWARE=y
#3 lore raw

PATCH 1/2 board/freescale: Introduce UBOOTBIN in spl template

In reply to Joris Offouga
Quoted 47 lines · Joris Offouga

For board like imx7d-pico u-boot.img change to u-boot-dtb.img in U-Boot v2019.07 so replace hard code u-boot.img with variable

---
 .../common/imx/genimage.cfg.template_no_boot_part_spl         | 4 ++--
 board/freescale/common/imx/genimage.cfg.template_spl          | 4 ++--
 board/freescale/common/imx/post-image.sh                      | 4 ++++
 3 files changed, 8 insertions(+), 4 deletions(-)
board/freescale/common/imx/genimage.cfg.template_no_boot_part_spl +2 -2
index 9cdecc6ce0..c29032572a 100644
@@ -17,9 +17,9 @@ image sdcard.img {
     offset = 1024
   }
 
-  partition u-boot-img {
+  partition u-boot {
     in-partition-table = "no"
-    image = "u-boot.img"
+    image = "%UBOOTBIN%"
     offset = 69K
   }
 
board/freescale/common/imx/genimage.cfg.template_spl +2 -2
index 0b6e22864b..d2d810777b 100644
@@ -26,9 +26,9 @@ image sdcard.img {
     offset = 1024
   }
 
-  partition u-boot-img {
+  partition u-boot {
     in-partition-table = "no"
-    image = "u-boot.img"
+    image = "%UBOOTBIN%"
     offset = 69K
   }
 
board/freescale/common/imx/post-image.sh +0 -0
index 12756c63d5..ab51dc2098 100755

board/freescale/common/imx/post-image.sh uboot_image() · line 71

Quoted 6 lines
board/freescale/common/imx/post-image.sh +3 -0
@@ -66,6 +66,10 @@ uboot_image()
 		echo "u-boot-dtb.imx"
 	elif grep -Eq "^BR2_TARGET_UBOOT_FORMAT_IMX=y$" ${BR2_CONFIG}; then
 		echo "u-boot.imx"
+	elif grep -Eq "^BR2_TARGET_UBOOT_FORMAT_DTB_IMG=y$" ${BR2_CONFIG}; then
+	    echo "u-boot-dtb.img"
+	elif grep -Eq "^BR2_TARGET_UBOOT_FORMAT_DTB_IMG=y$" ${BR2_CONFIG}; then

This should have been BR2_TARGET_UBOOT_FORMAT_IMG.

Applied to master with that fixed, and with a heavily reworked commit log, thanks.

Regards,
Arnout

Quoted 5 lines
board/freescale/common/imx/post-image.sh +1 -0
+	    echo "u-boot.img"
 	fi
 }
 
#4 lore raw

PATCH 1/2 board/freescale: Introduce UBOOTBIN in spl template

Le 09/07/2019 ? 20:06, Arnout Vandecappelle a ?crit?:

Quoted 44 lines · Joris Offouga
Quoted 42 lines

For board like imx7d-pico u-boot.img change to u-boot-dtb.img in U-Boot v2019.07 so replace hard code u-boot.img with variable

---
  .../common/imx/genimage.cfg.template_no_boot_part_spl         | 4 ++--
  board/freescale/common/imx/genimage.cfg.template_spl          | 4 ++--
  board/freescale/common/imx/post-image.sh                      | 4 ++++
  3 files changed, 8 insertions(+), 4 deletions(-)
board/freescale/common/imx/genimage.cfg.template_no_boot_part_spl +2 -2
index 9cdecc6ce0..c29032572a 100644
@@ -17,9 +17,9 @@ image sdcard.img {
      offset = 1024
    }
 
-  partition u-boot-img {
+  partition u-boot {
      in-partition-table = "no"
-    image = "u-boot.img"
+    image = "%UBOOTBIN%"
      offset = 69K
    }
 
board/freescale/common/imx/genimage.cfg.template_spl +2 -2
index 0b6e22864b..d2d810777b 100644
@@ -26,9 +26,9 @@ image sdcard.img {
      offset = 1024
    }
 
-  partition u-boot-img {
+  partition u-boot {
      in-partition-table = "no"
-    image = "u-boot.img"
+    image = "%UBOOTBIN%"
      offset = 69K
    }
 
Quoted 12 lines

board/freescale/common/imx/post-image.sh uboot_image() · line 71

Quoted 11 lines
board/freescale/common/imx/post-image.sh +3 -0
index 12756c63d5..ab51dc2098 100755
@@ -66,6 +66,10 @@ uboot_image()
  		echo "u-boot-dtb.imx"
  	elif grep -Eq "^BR2_TARGET_UBOOT_FORMAT_IMX=y$" ${BR2_CONFIG}; then
  		echo "u-boot.imx"
+	elif grep -Eq "^BR2_TARGET_UBOOT_FORMAT_DTB_IMG=y$" ${BR2_CONFIG}; then
+	    echo "u-boot-dtb.img"
+	elif grep -Eq "^BR2_TARGET_UBOOT_FORMAT_DTB_IMG=y$" ${BR2_CONFIG}; then

This should have been BR2_TARGET_UBOOT_FORMAT_IMG.

Indeed, i use wrong config, i send new patch for fix this:

https://github.com/buildroot/buildroot/commit/4f9f3a0e9695e670c707d938096ec620c612b694#diff-704e3d7e4d3563826a5c0db0ca5b696eR71

Also for U-Boot 2019.07, it is necessary to apply the series of Pierre-Jean

Best Regards,

Joris Offouga

Quoted 11 lines

Applied to master with that fixed, and with a heavily reworked commit log, thanks.

Regards,
Arnout

Quoted 5 lines
board/freescale/common/imx/post-image.sh +1 -0
+	    echo "u-boot.img"
  	fi
  }