Skip to contentSkip to conversation

drm/bridge: dw-hdmi: Refuse DDC/CI transfers on the internal I2C controller

PATCH Superseded Matthias Kaehlcke 4 participants 10 messages Jul 22, 2019 – Jul 31, 2019

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 drm/bridge: dw-hdmi: Refuse DDC/CI transfers on the internal I2C controller

The DDC/CI protocol involves sending a multi-byte request to the display via I2C, which is typically followed by a multi-byte response. The internal I2C controller only allows single byte reads/writes or reads of 8 sequential bytes, hence DDC/CI is not supported when the internal I2C controller is used. The I2C transfers complete without errors, however the data in the response is garbage. Abort transfers to/from slave address 0x37 (DDC) with -EOPNOTSUPP, to make it evident that the communication is failing.

---
Changes in v2:
- changed DDC_I2C_ADDR to DDC_CI_ADDR

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +8 -0
index 045b1b13fd0e..28933629f3c7 100644
@@ -35,6 +35,7 @@
 
 #include <media/cec-notifier.h>
 
+#define DDC_CI_ADDR		0x37
 #define DDC_SEGMENT_ADDR	0x30
 
 #define HDMI_EDID_LEN		512
@@ -322,6 +323,13 @@ static int dw_hdmi_i2c_xfer(struct i2c_adapter *adap,
 	u8 addr = msgs[0].addr;
 	int i, ret = 0;
 
+	if (addr == DDC_CI_ADDR)
+		/*
+		 * The internal I2C controller does not support the multi-byte
+		 * read and write operations needed for DDC/CI.
+		 */
+		return -EOPNOTSUPP;
+
 	dev_dbg(hdmi->dev, "xfer: num: %d, addr: %#x\n", num, addr);
 
 	for (i = 0; i < num; i++) {
Signature · 1 line
2.22.0.657.g960e92d24f-goog
Reviewed-by on v2 1/1
#1 lore raw

Hi,

Quoted 31 lines · Matthias Kaehlcke

The DDC/CI protocol involves sending a multi-byte request to the display via I2C, which is typically followed by a multi-byte response. The internal I2C controller only allows single byte reads/writes or reads of 8 sequential bytes, hence DDC/CI is not supported when the internal I2C controller is used. The I2C transfers complete without errors, however the data in the response is garbage. Abort transfers to/from slave address 0x37 (DDC) with -EOPNOTSUPP, to make it evident that the communication is failing.

---
Changes in v2:
- changed DDC_I2C_ADDR to DDC_CI_ADDR

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +1 -0
index 045b1b13fd0e..28933629f3c7 100644
@@ -35,6 +35,7 @@
 
 #include <media/cec-notifier.h>
 
+#define DDC_CI_ADDR            0x37
 #define DDC_SEGMENT_ADDR       0x30
 
 #define HDMI_EDID_LEN          512

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c static int dw_hdmi_i2c_xfer(struct i2c_adapter *adap, · line 332

Quoted 10 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +7 -0
@@ -322,6 +323,13 @@ static int dw_hdmi_i2c_xfer(struct i2c_adapter *adap,
        u8 addr = msgs[0].addr;
        int i, ret = 0;
 
+       if (addr == DDC_CI_ADDR)
+               /*
+                * The internal I2C controller does not support the multi-byte
+                * read and write operations needed for DDC/CI.
+                */
+               return -EOPNOTSUPP;
+

In theory we could also solve this by detecting (in other parts of the function) the bad multi-byte read/write operations. That would maybe be more generic (AKA it would more properly handle random userspace tools fiddling with i2c-dev) but add complexity to the code.

...possibly a better long-term solution is to just totally stop emulating a regular i2c adapter when the hardware just doesn't support that. In theory we could remove the "drm_get_edid()" call in dw_hdmi_connector_get_modes() and replace it with a direct call to drm_do_get_edid() if we're using the built-in adapter. Possibly "tda998x_drv.c" would be a good reference. If we did that, we could remove all the weird / hacky i2c code in this driver.

Since the bigger cleanup seems like a bit much to ask, I'm OK with this as a stopgap to at least prevent userspace tools from getting confused. Thus:

#2 lore raw
Quoted 37 lines · Doug Anderson

Hi,

Quoted 34 lines · Matthias Kaehlcke

The DDC/CI protocol involves sending a multi-byte request to the display via I2C, which is typically followed by a multi-byte response. The internal I2C controller only allows single byte reads/writes or reads of 8 sequential bytes, hence DDC/CI is not supported when the internal I2C controller is used. The I2C transfers complete without errors, however the data in the response is garbage. Abort transfers to/from slave address 0x37 (DDC) with -EOPNOTSUPP, to make it evident that the communication is failing.

---
Changes in v2:
- changed DDC_I2C_ADDR to DDC_CI_ADDR

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +1 -0
index 045b1b13fd0e..28933629f3c7 100644
@@ -35,6 +35,7 @@
 
 #include <media/cec-notifier.h>
 
+#define DDC_CI_ADDR            0x37
 #define DDC_SEGMENT_ADDR       0x30
 
 #define HDMI_EDID_LEN          512
@@ -322,6 +323,13 @@ static int dw_hdmi_i2c_xfer(struct i2c_adapter *adap,
        u8 addr = msgs[0].addr;
        int i, ret = 0;
 
Quoted 12 lines

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c static int dw_hdmi_i2c_xfer(struct i2c_adapter *adap, · line 332

Quoted 7 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +7 -0
+       if (addr == DDC_CI_ADDR)
+               /*
+                * The internal I2C controller does not support the multi-byte
+                * read and write operations needed for DDC/CI.
+                */
+               return -EOPNOTSUPP;
+

In theory we could also solve this by detecting (in other parts of the function) the bad multi-byte read/write operations. That would maybe be more generic (AKA it would more properly handle random userspace tools fiddling with i2c-dev) but add complexity to the code.

But how do you know it's an unsupported operation, and not the driver knowing the wacky limitations doing something valid.

E.g. you get the sequence:

0x01 0x0a 0x0b 0x0c 0x0d

This could be interpreted as "send the above bytes to the slave" or as "send 0x0a to address 0x01, 0x0b to 0x02, 0x0c to 0x03 and 0x0d to 0x04" (at least by this driver ;-) . The latter could be intended.

Quoted 7 lines

...possibly a better long-term solution is to just totally stop emulating a regular i2c adapter when the hardware just doesn't support that. In theory we could remove the "drm_get_edid()" call in dw_hdmi_connector_get_modes() and replace it with a direct call to drm_do_get_edid() if we're using the built-in adapter. Possibly "tda998x_drv.c" would be a good reference. If we did that, we could remove all the weird / hacky i2c code in this driver.

yes, that would be another and probably better option than trying to detect unsupported transaction.

Quoted 5 lines

Since the bigger cleanup seems like a bit much to ask, I'm OK with this as a stopgap to at least prevent userspace tools from getting confused. Thus:

Thanks!

#3 lore raw
In reply to Matthias Kaehlcke
Quoted 5 lines · Matthias Kaehlcke

The DDC/CI protocol involves sending a multi-byte request to the display via I2C, which is typically followed by a multi-byte response. The internal I2C controller only allows single byte reads/writes or reads of 8 sequential bytes, hence DDC/CI is not supported when the internal I2C controller is used. The I2C

This is very likely a stupid question, but I didn't see an answer for it, so I'll just ask :)

If the controller supports xfers of 8 bytes and 1 bytes, could you just split up any of these transactions into len/8+len%8 transactions?

Sean

Quoted 41 lines

transfers complete without errors, however the data in the response is garbage. Abort transfers to/from slave address 0x37 (DDC) with -EOPNOTSUPP, to make it evident that the communication is failing.

---
Changes in v2:
- changed DDC_I2C_ADDR to DDC_CI_ADDR

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +8 -0
index 045b1b13fd0e..28933629f3c7 100644
@@ -35,6 +35,7 @@
 
 #include <media/cec-notifier.h>
 
+#define DDC_CI_ADDR		0x37
 #define DDC_SEGMENT_ADDR	0x30
 
 #define HDMI_EDID_LEN		512
@@ -322,6 +323,13 @@ static int dw_hdmi_i2c_xfer(struct i2c_adapter *adap,
 	u8 addr = msgs[0].addr;
 	int i, ret = 0;
 
+	if (addr == DDC_CI_ADDR)
+		/*
+		 * The internal I2C controller does not support the multi-byte
+		 * read and write operations needed for DDC/CI.
+		 */
+		return -EOPNOTSUPP;
+
 	dev_dbg(hdmi->dev, "xfer: num: %d, addr: %#x\n", num, addr);
 
 	for (i = 0; i < num; i++) {
Signature · 1 line
2.22.0.657.g960e92d24f-goog
Signature · 5 lines
Sean Paul, Software Engineer, Google / Chromium OS
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#4 lore raw

Hi,

Quoted 8 lines · Sean Paul
Quoted 5 lines · Matthias Kaehlcke

The DDC/CI protocol involves sending a multi-byte request to the display via I2C, which is typically followed by a multi-byte response. The internal I2C controller only allows single byte reads/writes or reads of 8 sequential bytes, hence DDC/CI is not supported when the internal I2C controller is used. The I2C

Quoted 5 lines

This is very likely a stupid question, but I didn't see an answer for it, so I'll just ask :)

If the controller supports xfers of 8 bytes and 1 bytes, could you just split up any of these transactions into len/8+len%8 transactions?

It's not quite that easy, I think. Specifically a 1-byte transfer isn't really a 1-byte transfer.

It always sticks this on the wire for a 1-byte write:

Start
Slave address (7 bits) + write (1 bit)
(wait ack)
Register address
1 byte of data
wait for ack
Stop

...or for a 1-byte read:

Start
Slave address (7 bits) + write (1 bit)
(wait ack)
Register address
(wait ack)
Repeated Start (1 bit)
Slave address (7 bits) + read (1 bit)
(read 1 byte of data)
Ack
Stop

Putting more than one of those in a row is not the same thing as just doing a whole bunch of reads or a whole bunch of writes with no "stop" in between.

As far as I could find out about DDC/CI it's part of the spec to _not_ send the stop between the reads / writes.

-Doug

#5 lore raw
In reply to Sean Paul
Quoted 7 lines · Sean Paul
Quoted 5 lines · Matthias Kaehlcke

The DDC/CI protocol involves sending a multi-byte request to the display via I2C, which is typically followed by a multi-byte response. The internal I2C controller only allows single byte reads/writes or reads of 8 sequential bytes, hence DDC/CI is not supported when the internal I2C controller is used. The I2C

Quoted 5 lines

This is very likely a stupid question, but I didn't see an answer for it, so I'll just ask :)

If the controller supports xfers of 8 bytes and 1 bytes, could you just split up any of these transactions into len/8+len%8 transactions?

The controller interprets all transfers to be register accesses. It is not possible to just send the sequence '0x0a 0x0b 0x0c' as three byte transfers, the controller expects an address for each byte and (supposedly) sends it over the wire, which typically isn't what you want.

Also the 8-byte reads only seem to be supported in certain configurations ("when the DWC_HDMI_TX_20 parameter is enabled").

Quoted 37 lines
Quoted 37 lines

transfers complete without errors, however the data in the response is garbage. Abort transfers to/from slave address 0x37 (DDC) with -EOPNOTSUPP, to make it evident that the communication is failing.

---
Changes in v2:
- changed DDC_I2C_ADDR to DDC_CI_ADDR

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +8 -0
index 045b1b13fd0e..28933629f3c7 100644
@@ -35,6 +35,7 @@
 
 #include <media/cec-notifier.h>
 
+#define DDC_CI_ADDR		0x37
 #define DDC_SEGMENT_ADDR	0x30
 
 #define HDMI_EDID_LEN		512
@@ -322,6 +323,13 @@ static int dw_hdmi_i2c_xfer(struct i2c_adapter *adap,
 	u8 addr = msgs[0].addr;
 	int i, ret = 0;
 
+	if (addr == DDC_CI_ADDR)
+		/*
+		 * The internal I2C controller does not support the multi-byte
+		 * read and write operations needed for DDC/CI.
+		 */
+		return -EOPNOTSUPP;
+
 	dev_dbg(hdmi->dev, "xfer: num: %d, addr: %#x\n", num, addr);
 
Quoted 2 lines

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c static int dw_hdmi_i2c_xfer(struct i2c_adapter *adap, · line 335

Quoted 1 line
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +0 -0
 	for (i = 0; i < num; i++) {

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Reviewed-by
#6 lore raw
Quoted 14 lines · Matthias Kaehlcke
Quoted 7 lines · Sean Paul
Quoted 5 lines · Matthias Kaehlcke

The DDC/CI protocol involves sending a multi-byte request to the display via I2C, which is typically followed by a multi-byte response. The internal I2C controller only allows single byte reads/writes or reads of 8 sequential bytes, hence DDC/CI is not supported when the internal I2C controller is used. The I2C

Quoted 5 lines

This is very likely a stupid question, but I didn't see an answer for it, so I'll just ask :)

If the controller supports xfers of 8 bytes and 1 bytes, could you just split up any of these transactions into len/8+len%8 transactions?

Quoted 8 lines

The controller interprets all transfers to be register accesses. It is not possible to just send the sequence '0x0a 0x0b 0x0c' as three byte transfers, the controller expects an address for each byte and (supposedly) sends it over the wire, which typically isn't what you want.

Also the 8-byte reads only seem to be supported in certain configurations ("when the DWC_HDMI_TX_20 parameter is enabled").

Thanks for the detailed answers (both you and Doug)!

This change looks good to me, but I'll leave it to a dw-hdmi expert to apply. So fwiw,

Quoted 40 lines
Quoted 40 lines
Quoted 39 lines

transfers complete without errors, however the data in the response is garbage. Abort transfers to/from slave address 0x37 (DDC) with -EOPNOTSUPP, to make it evident that the communication is failing.

---
Changes in v2:
- changed DDC_I2C_ADDR to DDC_CI_ADDR

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +8 -0
index 045b1b13fd0e..28933629f3c7 100644
@@ -35,6 +35,7 @@
 
 #include <media/cec-notifier.h>
 
+#define DDC_CI_ADDR		0x37
 #define DDC_SEGMENT_ADDR	0x30
 
 #define HDMI_EDID_LEN		512
@@ -322,6 +323,13 @@ static int dw_hdmi_i2c_xfer(struct i2c_adapter *adap,
 	u8 addr = msgs[0].addr;
 	int i, ret = 0;
 
+	if (addr == DDC_CI_ADDR)
+		/*
+		 * The internal I2C controller does not support the multi-byte
+		 * read and write operations needed for DDC/CI.
+		 */
+		return -EOPNOTSUPP;
+
 	dev_dbg(hdmi->dev, "xfer: num: %d, addr: %#x\n", num, addr);
 
 	for (i = 0; i < num; i++) {
Signature · 1 line
Sean Paul, Software Engineer, Google / Chromium OS
#7 lore raw

Hi,

Quoted 21 lines · Sean Paul
Quoted 20 lines · Matthias Kaehlcke
Quoted 7 lines · Sean Paul
Quoted 5 lines · Matthias Kaehlcke

The DDC/CI protocol involves sending a multi-byte request to the display via I2C, which is typically followed by a multi-byte response. The internal I2C controller only allows single byte reads/writes or reads of 8 sequential bytes, hence DDC/CI is not supported when the internal I2C controller is used. The I2C

Quoted 5 lines

This is very likely a stupid question, but I didn't see an answer for it, so I'll just ask :)

If the controller supports xfers of 8 bytes and 1 bytes, could you just split up any of these transactions into len/8+len%8 transactions?

The controller interprets all transfers to be register accesses. It is not possible to just send the sequence '0x0a 0x0b 0x0c' as three byte transfers, the controller expects an address for each byte and (supposedly) sends it over the wire, which typically isn't what you want.

Quoted 7 lines
Quoted 2 lines

Also the 8-byte reads only seem to be supported in certain configurations ("when the DWC_HDMI_TX_20 parameter is enabled").

Thanks for the detailed answers (both you and Doug)!

This change looks good to me, but I'll leave it to a dw-hdmi expert to apply. So fwiw,

I'm not qualified as a dw-hdmi expert but until the internal i2c controller is exposed as a "standard" i2c adapter (which is a valuable feature), blacklisting a fixed address is wrong, and we should detect invalid/malformed transactions instead that doesn't fit in the HW model OR really stop emulating an i2c adapter.

Moving to drm_do_get_edid() would need to entirely rewrite or refactor communication code to handle the SCDC transactions, since they use an i2c adapter...

Neil

Quoted 45 lines
Quoted 40 lines
Quoted 40 lines
Quoted 39 lines

transfers complete without errors, however the data in the response is garbage. Abort transfers to/from slave address 0x37 (DDC) with -EOPNOTSUPP, to make it evident that the communication is failing.

---
Changes in v2:
- changed DDC_I2C_ADDR to DDC_CI_ADDR

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +8 -0
index 045b1b13fd0e..28933629f3c7 100644
@@ -35,6 +35,7 @@
 
 #include <media/cec-notifier.h>
 
+#define DDC_CI_ADDR		0x37
 #define DDC_SEGMENT_ADDR	0x30
 
 #define HDMI_EDID_LEN		512
@@ -322,6 +323,13 @@ static int dw_hdmi_i2c_xfer(struct i2c_adapter *adap,
 	u8 addr = msgs[0].addr;
 	int i, ret = 0;
 
+	if (addr == DDC_CI_ADDR)
+		/*
+		 * The internal I2C controller does not support the multi-byte
+		 * read and write operations needed for DDC/CI.
+		 */
+		return -EOPNOTSUPP;
+
 	dev_dbg(hdmi->dev, "xfer: num: %d, addr: %#x\n", num, addr);
 
 	for (i = 0; i < num; i++) {
#8 lore raw
Quoted 29 lines · Neil Armstrong

Hi,

Quoted 26 lines · Sean Paul
Quoted 14 lines · Matthias Kaehlcke
Quoted 7 lines · Sean Paul
Quoted 5 lines · Matthias Kaehlcke

The DDC/CI protocol involves sending a multi-byte request to the display via I2C, which is typically followed by a multi-byte response. The internal I2C controller only allows single byte reads/writes or reads of 8 sequential bytes, hence DDC/CI is not supported when the internal I2C controller is used. The I2C

Quoted 5 lines

This is very likely a stupid question, but I didn't see an answer for it, so I'll just ask :)

If the controller supports xfers of 8 bytes and 1 bytes, could you just split up any of these transactions into len/8+len%8 transactions?

Quoted 8 lines

The controller interprets all transfers to be register accesses. It is not possible to just send the sequence '0x0a 0x0b 0x0c' as three byte transfers, the controller expects an address for each byte and (supposedly) sends it over the wire, which typically isn't what you want.

Also the 8-byte reads only seem to be supported in certain configurations ("when the DWC_HDMI_TX_20 parameter is enabled").

Thanks for the detailed answers (both you and Doug)!

Quoted 8 lines
Quoted 2 lines

This change looks good to me, but I'll leave it to a dw-hdmi expert to apply. So fwiw,

I'm not qualified as a dw-hdmi expert but until the internal i2c controller is exposed as a "standard" i2c adapter (which is a valuable feature), blacklisting a fixed address is wrong, and we should detect invalid/malformed transactions instead that doesn't fit in the HW model OR really stop emulating an i2c adapter.

I think we all agree on this (and Doug mentioned it upthread). That said, the driver is currently returning successful status and garbage data. I think that's objectively worse than returning an error, and this patch really doesn't prevent us from doing it right in the future.

If the code wasn't already upstream, I agree we should pivot to the correct solution. But unless someone volunteers to fix this the right way, I don't have a problem with this patch for now.

Sean

Quoted 52 lines

Moving to drm_do_get_edid() would need to entirely rewrite or refactor communication code to handle the SCDC transactions, since they use an i2c adapter...

Neil

Quoted 45 lines
Quoted 40 lines
Quoted 40 lines
Quoted 39 lines

transfers complete without errors, however the data in the response is garbage. Abort transfers to/from slave address 0x37 (DDC) with -EOPNOTSUPP, to make it evident that the communication is failing.

---
Changes in v2:
- changed DDC_I2C_ADDR to DDC_CI_ADDR

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +8 -0
index 045b1b13fd0e..28933629f3c7 100644
@@ -35,6 +35,7 @@
 
 #include <media/cec-notifier.h>
 
+#define DDC_CI_ADDR		0x37
 #define DDC_SEGMENT_ADDR	0x30
 
 #define HDMI_EDID_LEN		512
@@ -322,6 +323,13 @@ static int dw_hdmi_i2c_xfer(struct i2c_adapter *adap,
 	u8 addr = msgs[0].addr;
 	int i, ret = 0;
 
+	if (addr == DDC_CI_ADDR)
+		/*
+		 * The internal I2C controller does not support the multi-byte
+		 * read and write operations needed for DDC/CI.
+		 */
+		return -EOPNOTSUPP;
+
 	dev_dbg(hdmi->dev, "xfer: num: %d, addr: %#x\n", num, addr);
 
 	for (i = 0; i < num; i++) {
Signature · 1 line
Sean Paul, Software Engineer, Google / Chromium OS
#9 lore raw
Quoted 39 lines · Sean Paul
Quoted 29 lines · Neil Armstrong

Hi,

Quoted 26 lines · Sean Paul
Quoted 14 lines · Matthias Kaehlcke
Quoted 7 lines · Sean Paul
Quoted 5 lines · Matthias Kaehlcke

The DDC/CI protocol involves sending a multi-byte request to the display via I2C, which is typically followed by a multi-byte response. The internal I2C controller only allows single byte reads/writes or reads of 8 sequential bytes, hence DDC/CI is not supported when the internal I2C controller is used. The I2C

Quoted 5 lines

This is very likely a stupid question, but I didn't see an answer for it, so I'll just ask :)

If the controller supports xfers of 8 bytes and 1 bytes, could you just split up any of these transactions into len/8+len%8 transactions?

Quoted 8 lines

The controller interprets all transfers to be register accesses. It is not possible to just send the sequence '0x0a 0x0b 0x0c' as three byte transfers, the controller expects an address for each byte and (supposedly) sends it over the wire, which typically isn't what you want.

Also the 8-byte reads only seem to be supported in certain configurations ("when the DWC_HDMI_TX_20 parameter is enabled").

Thanks for the detailed answers (both you and Doug)!

Quoted 8 lines
Quoted 2 lines

This change looks good to me, but I'll leave it to a dw-hdmi expert to apply. So fwiw,

I'm not qualified as a dw-hdmi expert but until the internal i2c controller is exposed as a "standard" i2c adapter (which is a valuable feature), blacklisting a fixed address is wrong, and we should detect invalid/malformed transactions instead that doesn't fit in the HW model OR really stop emulating an i2c adapter.

Quoted 8 lines

I think we all agree on this (and Doug mentioned it upthread). That said, the driver is currently returning successful status and garbage data. I think that's objectively worse than returning an error, and this patch really doesn't prevent us from doing it right in the future.

If the code wasn't already upstream, I agree we should pivot to the correct solution. But unless someone volunteers to fix this the right way, I don't have a problem with this patch for now.

Acked with an updated comment, example :
+ /*
+ * The internal I2C controller does not support the multi-byte
+ * read and write operations needed for DDC/CI.
+ * TOFIX: Blacklist the DDC/CI address until we filter out
+ * unsupported I2C operations.
+ */

Neil

Quoted 56 lines

Sean

Quoted 52 lines

Moving to drm_do_get_edid() would need to entirely rewrite or refactor communication code to handle the SCDC transactions, since they use an i2c adapter...

Neil

Quoted 45 lines
Quoted 40 lines
Quoted 40 lines
Quoted 39 lines

transfers complete without errors, however the data in the response is garbage. Abort transfers to/from slave address 0x37 (DDC) with -EOPNOTSUPP, to make it evident that the communication is failing.

---
Changes in v2:
- changed DDC_I2C_ADDR to DDC_CI_ADDR

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +8 -0
index 045b1b13fd0e..28933629f3c7 100644
@@ -35,6 +35,7 @@
 
 #include <media/cec-notifier.h>
 
+#define DDC_CI_ADDR		0x37
 #define DDC_SEGMENT_ADDR	0x30
 
 #define HDMI_EDID_LEN		512
@@ -322,6 +323,13 @@ static int dw_hdmi_i2c_xfer(struct i2c_adapter *adap,
 	u8 addr = msgs[0].addr;
 	int i, ret = 0;
 
+	if (addr == DDC_CI_ADDR)
+		/*
+		 * The internal I2C controller does not support the multi-byte
+		 * read and write operations needed for DDC/CI.
+		 */
+		return -EOPNOTSUPP;
+
 	dev_dbg(hdmi->dev, "xfer: num: %d, addr: %#x\n", num, addr);
 
 	for (i = 0; i < num; i++) {