Skip to contentSkip to conversation

ARM: omap3_logic: Enable OMAP EHCI support for SOM-LV Boards

PATCH New Adam Ford 2 participants 4 messages Jun 30, 2019 – Jul 28, 2019

lore
Share & tools
lore

Adam Ford

author
#0 lore raw

PATCH 1/2 ARM: omap3_logic: Enable OMAP EHCI support for SOM-LV Boards

The SOM-LV boards support the OMAP EHCI driver using port 2. With the driver updated to support device tree, this patch sets the corresponding pin muxing for the tranceiver as well as the reset pin.

board/logicpd/omap3som/omap3logic.h +19 -0
index aeb26b90d7..63c2141783 100644
@@ -161,12 +161,14 @@ void set_muxconf_regs(void)
 	MUX_VAL(CP(ETK_D7_ES2), (IEN  | PTD | DIS | M0)); /*ETK_D7*/
 	MUX_VAL(CP(ETK_D8_ES2), (IEN  | PTD | DIS | M0)); /*ETK_D8*/
 	MUX_VAL(CP(ETK_D9_ES2), (IEN  | PTD | DIS | M0)); /*ETK_D9*/
+#ifndef CONFIG_USB_EHCI_OMAP /* Torpedo does not use EHCI_OMAP */
 	MUX_VAL(CP(ETK_D10_ES2), (IEN  | PTD | DIS | M0)); /*ETK_D10*/
 	MUX_VAL(CP(ETK_D11_ES2), (IEN  | PTD | DIS | M0)); /*ETK_D11*/
 	MUX_VAL(CP(ETK_D12_ES2), (IEN  | PTD | DIS | M0)); /*ETK_D12*/
 	MUX_VAL(CP(ETK_D13_ES2), (IEN  | PTD | DIS | M0)); /*ETK_D13*/
 	MUX_VAL(CP(ETK_D14_ES2), (IEN  | PTD | DIS | M0)); /*ETK_D14*/
 	MUX_VAL(CP(ETK_D15_ES2), (IEN  | PTD | DIS | M0)); /*ETK_D15*/
+#endif
 
 	MUX_VAL(CP(D2D_MCAD1), (IEN  | PTD | EN  | M0)); /*d2d_mcad1*/
 	MUX_VAL(CP(D2D_MCAD2), (IEN  | PTD | EN  | M0)); /*d2d_mcad2*/
@@ -231,6 +233,23 @@ void set_muxconf_regs(void)
 	MUX_VAL(CP(D2D_SREAD),   (IEN  | PTD | DIS | M0)); /*d2d_sread*/
 	MUX_VAL(CP(D2D_MBUSFLAG), (IEN  | PTD | DIS | M0)); /*d2d_mbusflag*/
 	MUX_VAL(CP(D2D_SBUSFLAG), (IEN  | PTD | DIS | M0)); /*d2d_sbusflag*/
+
+#ifdef CONFIG_USB_EHCI_OMAP /* SOM-LV Uses EHCI-OMAP */
+	MUX_VAL(CP(ETK_D14_ES2),	(IEN  | PTD | DIS | M3));	/*HSUSB2_DATA0*/
+	MUX_VAL(CP(ETK_D15_ES2),	(IEN  | PTD | DIS | M3));	/*HSUSB2_DATA1*/
+	MUX_VAL(CP(MCSPI1_CS3),		(IEN  | PTD | EN  | M0));	/*HSUSB2_DATA2*/
+	MUX_VAL(CP(MCSPI2_CS1),		(IEN  | PTD | EN  | M0));	/*HSUSB2_DATA3*/
+	MUX_VAL(CP(MCSPI2_SIMO),	(IEN  | PTD | DIS | M0));	/*HSUSB2_DATA4*/
+	MUX_VAL(CP(MCSPI2_SOMI),	(IEN  | PTD | DIS | M0));	/*HSUSB2_DATA5*/
+	MUX_VAL(CP(MCSPI2_CS0),		(IEN  | PTD | EN  | M0));	/*HSUSB2_DATA6*/
+	MUX_VAL(CP(MCSPI2_CLK),		(IEN  | PTD | DIS | M0));	/*HSUSB2_DATA7*/
+	MUX_VAL(CP(SYS_BOOT2),      (IEN  | PTD | DIS | M4)) 	/* GPIO_4 */
+	MUX_VAL(CP(ETK_D10_ES2),	(IDIS | PTU | DIS | M3));	/*HSUSB2_CLK*/
+	MUX_VAL(CP(ETK_D11_ES2),	(IDIS | PTU | DIS | M3));	/*HSUSB2_STP*/
+	MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTU | DIS | M3));	/*HSUSB2_DIR*/
+	MUX_VAL(CP(ETK_D13_ES2),	(IEN  | PTD | DIS | M3));	/*HSUSB2_NXT*/
+#endif
+
 }
 
 #endif
include/configs/omap3_logic.h +4 -0
index e318a9f896..a5ae93914d 100644
@@ -30,6 +30,10 @@
 /* I2C */
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM AT24C64      */
 
+#ifdef CONFIG_USB_EHCI_OMAP
+#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO	4
+#endif
+
 /* Board NAND Info. */
 #ifdef CONFIG_NAND
 #define CONFIG_SYS_MAX_NAND_DEVICE	1	  /* Max number of */
Signature · 1 line
2.17.1
author
#1 lore raw

PATCH 2/2 ARM: omap3_logic & omap35_logic: Disable OMAP EHCI for Torpedo

The OMAP35 and AM/DM37 Torpedo boards do not have a USB tranceiver connected to the USB host port, so this patch removes it from the defconfig files.

configs/omap35_logic_defconfig +1 -0
index 3a529e8836..055a1bf489 100644
@@ -69,6 +69,7 @@ CONFIG_USB=y
 CONFIG_DM_USB=y
 # CONFIG_SPL_DM_USB is not set
 CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_OMAP is not set
 CONFIG_USB_MUSB_HOST=y
 CONFIG_USB_MUSB_OMAP2PLUS=y
 CONFIG_TWL4030_USB=y
configs/omap3_logic_defconfig +1 -0
index 0868e33131..b259b3720e 100644
@@ -68,6 +68,7 @@ CONFIG_USB=y
 CONFIG_DM_USB=y
 # CONFIG_SPL_DM_USB is not set
 CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_OMAP is not set
 CONFIG_USB_MUSB_HOST=y
 CONFIG_USB_MUSB_OMAP2PLUS=y
 CONFIG_TWL4030_USB=y
Signature · 1 line
2.17.1
#2 lore raw

PATCH 2/2 ARM: omap3_logic & omap35_logic: Disable OMAP EHCI for Torpedo

configs/omap35_logic_defconfig

Quoted 8 lines · Adam Ford

The OMAP35 and AM/DM37 Torpedo boards do not have a USB tranceiver connected to the USB host port, so this patch removes it from the defconfig files.

configs/omap35_logic_defconfig +0 -0
index 3a529e8836..055a1bf489 100644

Applied to u-boot/master, thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190728/5381fc4d/attachment.sig>
#3 lore raw

PATCH 1/2 ARM: omap3_logic: Enable OMAP EHCI support for SOM-LV Boards

In reply to Adam Ford

board/logicpd/omap3som/omap3logic.h

Quoted 9 lines · Adam Ford

The SOM-LV boards support the OMAP EHCI driver using port 2. With the driver updated to support device tree, this patch sets the corresponding pin muxing for the tranceiver as well as the reset pin.

board/logicpd/omap3som/omap3logic.h +0 -0
index aeb26b90d7..63c2141783 100644

Applied to u-boot/master, thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190728/1013315b/attachment.sig>