Skip to contentSkip to conversation

Allwinner H6 SPDIF support

PATCH Applied Clément Péron 2 participants 4 messages Aug 12, 2019

Subsystems (2)

v6 of 7 Applied Latest is v7 →

lore
Share & tools
lore
#0 lore raw

v6 cover Allwinner H6 SPDIF support

Allwinner H6 SoC has a SPDIF controller called One Wire Audio (OWA) which is different from the previous H3 generation and not compatible.

Difference are an increase of fifo sizes, some memory mapping are different and there is now the possibility to output the master clock on a pin.

Actually all these features are unused and only a bit for flushing the TX fifo is required.

Changes since v5:
- Move soundcard to board device-tree

Changes since v4:
- rename audio card name to sun50i-h6-spdif
- drop patches already merged

Changes since v3:
- rename reg_fctl_ftx to val_fctl_ftx
- rebase this series on sound-next
- fix dt-bindings due to change in sound-next
- change node name sound_spdif to sound-spdif

Changes since v2:
- Split quirks and H6 support patch
- Add specific section for quirks comment

Changes since v1:
- Remove H3 compatible
- Add TX fifo bit flush quirks
- Add H6 bindings in SPDIF driver

Clément Péron (2):
arm64: dts: allwinner: Add SPDIF node for Allwinner H6
arm64: dts: allwinner: h6: Enable SPDIF for Beelink GS1

 .../dts/allwinner/sun50i-h6-beelink-gs1.dts   | 22 +++++++++++++++++++
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi  | 20 +++++++++++++++++
 2 files changed, 42 insertions(+)
Signature · 6 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190812105115.26676-1-peron.clem%40gmail.com.
#1 lore raw

PATCH v6 1/2 arm64: dts: allwinner: Add SPDIF node for Allwinner H6

The Allwinner H6 has a SPDIF controller called OWA (One Wire Audio).

Only one pinmuxing is available so set it as default.

---
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +20 -0
index 7628a7c83096..2ba9ab9e0924 100644
@@ -282,6 +282,11 @@
 				bias-pull-up;
 			};
 
+			spdif_tx_pin: spdif-tx-pin {
+				pins = "PH7";
+				function = "spdif";
+			};
+
 			uart0_ph_pins: uart0-ph-pins {
 				pins = "PH0", "PH1";
 				function = "uart0";
@@ -411,6 +416,21 @@
 			};
 		};
 
+		spdif: spdif@5093000 {
+			#sound-dai-cells = <0>;
+			compatible = "allwinner,sun50i-h6-spdif";
+			reg = <0x05093000 0x400>;
+			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
+			clock-names = "apb", "spdif";
+			resets = <&ccu RST_BUS_SPDIF>;
+			dmas = <&dma 2>;
+			dma-names = "tx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&spdif_tx_pin>;
+			status = "disabled";
+		};
+
 		usb2otg: usb@5100000 {
 			compatible = "allwinner,sun50i-h6-musb",
 				     "allwinner,sun8i-a33-musb";
Signature · 6 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190812105115.26676-2-peron.clem%40gmail.com.
#2 lore raw

PATCH v6 2/2 arm64: dts: allwinner: h6: Enable SPDIF for Beelink GS1

In reply to Clément Péron

Beelink GS1 board has a SPDIF out connector, so enable it in the device-tree and add a simple SPDIF soundcard.

---
 .../dts/allwinner/sun50i-h6-beelink-gs1.dts   | 22 +++++++++++++++++++
 1 file changed, 22 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts +22 -0
index 0dc33c90dd60..4bd14f085070 100644
@@ -51,6 +51,24 @@
 		regulator-max-microvolt = <5000000>;
 		regulator-always-on;
 	};
+
+	sound-spdif {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "sun50i-h6-spdif";
+
+		simple-audio-card,cpu {
+			sound-dai = <&spdif>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&spdif_out>;
+		};
+	};
+
+	spdif_out: spdif-out {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dit";
+	};
 };
 
 &de {
@@ -243,6 +261,10 @@
 	vcc-pm-supply = <&reg_aldo1>;
 };
 
+&spdif {
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_ph_pins>;
Signature · 6 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190812105115.26676-3-peron.clem%40gmail.com.
#3 lore raw
In reply to Clément Péron
Quoted 8 lines · Clément Péron

Allwinner H6 SoC has a SPDIF controller called One Wire Audio (OWA) which is different from the previous H3 generation and not compatible.

Difference are an increase of fifo sizes, some memory mapping are different and there is now the possibility to output the master clock on a pin.

Actually all these features are unused and only a bit for flushing the TX fifo is required.

Applied both, thanks

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

Signature · 3 lines
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190812112328.o6xznp2mvnuchswe%40flea.