Allwinner H6 SPDIF support
Subsystems (2)
v6 cover Allwinner H6 SPDIF support
Allwinner H6 SoC has a SPDIF controller called One Wire Audio (OWA) which is different from the previous H3 generation and not compatible.
Difference are an increase of fifo sizes, some memory mapping are different and there is now the possibility to output the master clock on a pin.
Actually all these features are unused and only a bit for flushing the TX fifo is required.
Changes since v5:
- Move soundcard to board device-tree
Changes since v4:
- rename audio card name to sun50i-h6-spdif
- drop patches already merged
Changes since v3:
- rename reg_fctl_ftx to val_fctl_ftx
- rebase this series on sound-next
- fix dt-bindings due to change in sound-next
- change node name sound_spdif to sound-spdif
Changes since v2:
- Split quirks and H6 support patch
- Add specific section for quirks comment
Changes since v1:
- Remove H3 compatible
- Add TX fifo bit flush quirks
- Add H6 bindings in SPDIF driver
Clément Péron (2):
arm64: dts: allwinner: Add SPDIF node for Allwinner H6
arm64: dts: allwinner: h6: Enable SPDIF for Beelink GS1
.../dts/allwinner/sun50i-h6-beelink-gs1.dts | 22 +++++++++++++++++++ arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 20 +++++++++++++++++ 2 files changed, 42 insertions(+)
Signature · 6 lines
2.20.1 -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected] To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190812105115.26676-1-peron.clem%40gmail.com.
PATCH v6 1/2 arm64: dts: allwinner: Add SPDIF node for Allwinner H6
The Allwinner H6 has a SPDIF controller called OWA (One Wire Audio).
Only one pinmuxing is available so set it as default.
--- arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +20 -0
@@ -282,6 +282,11 @@ bias-pull-up; }; + spdif_tx_pin: spdif-tx-pin { + pins = "PH7"; + function = "spdif"; + }; + uart0_ph_pins: uart0-ph-pins { pins = "PH0", "PH1"; function = "uart0";
@@ -411,6 +416,21 @@ }; }; + spdif: spdif@5093000 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun50i-h6-spdif"; + reg = <0x05093000 0x400>; + interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>; + clock-names = "apb", "spdif"; + resets = <&ccu RST_BUS_SPDIF>; + dmas = <&dma 2>; + dma-names = "tx"; + pinctrl-names = "default"; + pinctrl-0 = <&spdif_tx_pin>; + status = "disabled"; + }; + usb2otg: usb@5100000 { compatible = "allwinner,sun50i-h6-musb", "allwinner,sun8i-a33-musb";
Signature · 6 lines
2.20.1 -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected] To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190812105115.26676-2-peron.clem%40gmail.com.
PATCH v6 2/2 arm64: dts: allwinner: h6: Enable SPDIF for Beelink GS1
In reply to Clément PéronBeelink GS1 board has a SPDIF out connector, so enable it in the device-tree and add a simple SPDIF soundcard.
--- .../dts/allwinner/sun50i-h6-beelink-gs1.dts | 22 +++++++++++++++++++ 1 file changed, 22 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts +22 -0
@@ -51,6 +51,24 @@ regulator-max-microvolt = <5000000>; regulator-always-on; }; + + sound-spdif { + compatible = "simple-audio-card"; + simple-audio-card,name = "sun50i-h6-spdif"; + + simple-audio-card,cpu { + sound-dai = <&spdif>; + }; + + simple-audio-card,codec { + sound-dai = <&spdif_out>; + }; + }; + + spdif_out: spdif-out { + #sound-dai-cells = <0>; + compatible = "linux,spdif-dit"; + }; }; &de {
@@ -243,6 +261,10 @@ vcc-pm-supply = <®_aldo1>; }; +&spdif { + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_ph_pins>;
Signature · 6 lines
2.20.1 -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected] To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190812105115.26676-3-peron.clem%40gmail.com.
Maxime Ripard
AppliedQuoted 8 lines · Clément Péron
Allwinner H6 SoC has a SPDIF controller called One Wire Audio (OWA) which is different from the previous H3 generation and not compatible.
Difference are an increase of fifo sizes, some memory mapping are different and there is now the possibility to output the master clock on a pin.
Actually all these features are unused and only a bit for flushing the TX fifo is required.
Applied both, thanks
Maxime
--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
Signature · 3 lines
You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected] To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190812112328.o6xznp2mvnuchswe%40flea.