Skip to contentSkip to conversation

Fix PHYLINK handling of ethtool ksettings with no PHY

RFC PATCH In review Vladimir Oltean 2 participants 4 messages Aug 28, 2019 – Aug 29, 2019

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

cover Fix PHYLINK handling of ethtool ksettings with no PHY

Logically speaking, this patch pertains to the "Fix issues in tc-taprio and tc-cbs" series at:
https://patchwork.ozlabs.org/project/netdev/list/?series=127821&state=*

The reason why I did not submit this patch together with those is that I don't know whether the error condition can happen in current mainline Linux at the moment. I am running Arseny's RFC patch "gianfar: convert to phylink" and have found that __ethtool_get_link_ksettings returns a speed of 0 instead of SPEED_UNKNOWN when there is no PHY connected.

Gianfar has carried this oddity over from its PHYLIB days, where it connects "late" to the PHY. I am not sure whether PHYLINK, gianfar, or both, need to be changed. Comments welcome.

Vladimir Oltean (1):
phylink: Set speed to SPEED_UNKNOWN when there is no PHY connected

 drivers/net/phy/phylink.c | 1 +
 1 file changed, 1 insertion(+)
Signature · 1 line
2.17.1
#1 lore raw

RFC PATCH 1/1 phylink: Set speed to SPEED_UNKNOWN when there is no PHY connected

phylink_ethtool_ksettings_get can be called while the interface may not even be up, which should not be a problem. But there are drivers (e.g. gianfar) which connect to the PHY in .ndo_open and disconnect in .ndo_close. While odd, to my knowledge this is again not illegal and there may be more that do the same. But PHYLINK for example has this check in phylink_ethtool_ksettings_get:

	if (pl->phydev) {
		phy_ethtool_ksettings_get(pl->phydev, kset);
	} else {
		kset->base.port = pl->link_port;
	}

So it will not populate kset->base.speed if there is no PHY connected. The speed will be 0, by way of a previous memset. Not SPEED_UNKNOWN. It is arguable whether that is legal or not. include/uapi/linux/ethtool.h says:

All values 0 to INT_MAX are legal.

By that measure it may be. But it sure would make users of the __ethtool_get_link_ksettings API need make more complicated checks (against -1, against 0, 1, etc). So far the kernel community has been ok with just checking for SPEED_UNKNOWN.

Take net/sched/sch_taprio.c for example. The check in taprio_set_picos_per_byte is currently not robust enough and will trigger this division by zero, due to PHYLINK not setting SPEED_UNKNOWN:

	if (!__ethtool_get_link_ksettings(dev, &ecmd) &&
	    ecmd.base.speed != SPEED_UNKNOWN)
		picos_per_byte = div64_s64(NSEC_PER_SEC * 1000LL * 8,
					   ecmd.base.speed * 1000 * 1000);
[   27.109992] Division by zero in kernel.
[   27.113842] CPU: 1 PID: 198 Comm: tc Not tainted 5.3.0-rc5-01246-gc4006b8c2637-dirty #212
[   27.121974] Hardware name: Freescale LS1021A
[   27.126234] [<c03132e0>] (unwind_backtrace) from [<c030d8b8>] (show_stack+0x10/0x14)
[   27.133938] [<c030d8b8>] (show_stack) from [<c10b21b0>] (dump_stack+0xb0/0xc4)
[   27.141124] [<c10b21b0>] (dump_stack) from [<c10af97c>] (Ldiv0_64+0x8/0x18)
[   27.148052] [<c10af97c>] (Ldiv0_64) from [<c0700260>] (div64_u64+0xcc/0xf0)
[   27.154978] [<c0700260>] (div64_u64) from [<c07002d0>] (div64_s64+0x4c/0x68)
[   27.161993] [<c07002d0>] (div64_s64) from [<c0f3d890>] (taprio_set_picos_per_byte+0xe8/0xf4)
[   27.170388] [<c0f3d890>] (taprio_set_picos_per_byte) from [<c0f3f614>] (taprio_change+0x668/0xcec)
[   27.179302] [<c0f3f614>] (taprio_change) from [<c0f2bc24>] (qdisc_create+0x1fc/0x4f4)
[   27.187091] [<c0f2bc24>] (qdisc_create) from [<c0f2c0c8>] (tc_modify_qdisc+0x1ac/0x6f8)
[   27.195055] [<c0f2c0c8>] (tc_modify_qdisc) from [<c0ee9604>] (rtnetlink_rcv_msg+0x268/0x2dc)
[   27.203449] [<c0ee9604>] (rtnetlink_rcv_msg) from [<c0f4fef0>] (netlink_rcv_skb+0xe0/0x114)
[   27.211756] [<c0f4fef0>] (netlink_rcv_skb) from [<c0f4f6cc>] (netlink_unicast+0x1b4/0x22c)
[   27.219977] [<c0f4f6cc>] (netlink_unicast) from [<c0f4fa84>] (netlink_sendmsg+0x284/0x340)
[   27.228198] [<c0f4fa84>] (netlink_sendmsg) from [<c0eae5fc>] (sock_sendmsg+0x14/0x24)
[   27.235988] [<c0eae5fc>] (sock_sendmsg) from [<c0eaedf8>] (___sys_sendmsg+0x214/0x228)
[   27.243863] [<c0eaedf8>] (___sys_sendmsg) from [<c0eb015c>] (__sys_sendmsg+0x50/0x8c)
[   27.251652] [<c0eb015c>] (__sys_sendmsg) from [<c0301000>] (ret_fast_syscall+0x0/0x54)
[   27.259524] Exception stack(0xe8045fa8 to 0xe8045ff0)
[   27.264546] 5fa0:                   b6f608c8 000000f8 00000003 bed7e2f0 00000000 00000000
[   27.272681] 5fc0: b6f608c8 000000f8 004ce54c 00000128 5d3ce8c7 00000000 00000026 00505c9c
[   27.280812] 5fe0: 00000070 bed7e298 004ddd64 b6dd1e64
Cc Russell King <[email protected]>
Fixes 9525ae83959b ("phylink: add phylink infrastructure")
---
 drivers/net/phy/phylink.c | 1 +
 1 file changed, 1 insertion(+)
drivers/net/phy/phylink.c +1 -0
index a45c5de96ab1..3522eaf3e80c 100644
@@ -1112,6 +1112,7 @@ int phylink_ethtool_ksettings_get(struct phylink *pl,
 	if (pl->phydev) {
 		phy_ethtool_ksettings_get(pl->phydev, kset);
 	} else {
+		kset->base.speed = SPEED_UNKNOWN;
 		kset->base.port = pl->link_port;
 	}
 
Signature · 1 line
2.17.1
#2 lore raw

Re: [RFC PATCH 1/1] phylink: Set speed to SPEED_UNKNOWN when there is no PHY connected

Quoted 25 lines · Vladimir Oltean

phylink_ethtool_ksettings_get can be called while the interface may not even be up, which should not be a problem. But there are drivers (e.g. gianfar) which connect to the PHY in .ndo_open and disconnect in .ndo_close. While odd, to my knowledge this is again not illegal and there may be more that do the same. But PHYLINK for example has this check in phylink_ethtool_ksettings_get:

	if (pl->phydev) {
		phy_ethtool_ksettings_get(pl->phydev, kset);
	} else {
		kset->base.port = pl->link_port;
	}

So it will not populate kset->base.speed if there is no PHY connected. The speed will be 0, by way of a previous memset. Not SPEED_UNKNOWN. It is arguable whether that is legal or not. include/uapi/linux/ethtool.h says:

All values 0 to INT_MAX are legal.

By that measure it may be. But it sure would make users of the __ethtool_get_link_ksettings API need make more complicated checks (against -1, against 0, 1, etc). So far the kernel community has been ok with just checking for SPEED_UNKNOWN.

Quoted 8 lines

Take net/sched/sch_taprio.c for example. The check in taprio_set_picos_per_byte is currently not robust enough and will trigger this division by zero, due to PHYLINK not setting SPEED_UNKNOWN:

	if (!__ethtool_get_link_ksettings(dev, &ecmd) &&
	    ecmd.base.speed != SPEED_UNKNOWN)
		picos_per_byte = div64_s64(NSEC_PER_SEC * 1000LL * 8,
					   ecmd.base.speed * 1000 * 1000);

The ethtool API says:

* If it is enabled then they are read-only; if the link
* is up they represent the negotiated link mode; if the link is down,
* the speed is 0, %SPEED_UNKNOWN or the highest enabled speed and
* @duplex is %DUPLEX_UNKNOWN or the best enabled duplex mode.

So, it seems that taprio is not following the API... I'd suggest either fixing taprio, or getting agreement to change the ethtool API.

Signature · 3 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
#3 lore raw

Re: [RFC PATCH 1/1] phylink: Set speed to SPEED_UNKNOWN when there is no PHY connected

Hi Russell,

Quoted 38 lines · Russell King - ARM Linux admin
Quoted 25 lines · Vladimir Oltean

phylink_ethtool_ksettings_get can be called while the interface may not even be up, which should not be a problem. But there are drivers (e.g. gianfar) which connect to the PHY in .ndo_open and disconnect in .ndo_close. While odd, to my knowledge this is again not illegal and there may be more that do the same. But PHYLINK for example has this check in phylink_ethtool_ksettings_get:

      if (pl->phydev) {
              phy_ethtool_ksettings_get(pl->phydev, kset);
      } else {
              kset->base.port = pl->link_port;
      }

So it will not populate kset->base.speed if there is no PHY connected. The speed will be 0, by way of a previous memset. Not SPEED_UNKNOWN. It is arguable whether that is legal or not. include/uapi/linux/ethtool.h says:

All values 0 to INT_MAX are legal.

By that measure it may be. But it sure would make users of the __ethtool_get_link_ksettings API need make more complicated checks (against -1, against 0, 1, etc). So far the kernel community has been ok with just checking for SPEED_UNKNOWN.

Quoted 8 lines

Take net/sched/sch_taprio.c for example. The check in taprio_set_picos_per_byte is currently not robust enough and will trigger this division by zero, due to PHYLINK not setting SPEED_UNKNOWN:

      if (!__ethtool_get_link_ksettings(dev, &ecmd) &&
          ecmd.base.speed != SPEED_UNKNOWN)
              picos_per_byte = div64_s64(NSEC_PER_SEC * 1000LL * 8,
                                         ecmd.base.speed * 1000 * 1000);

The ethtool API says:

Quoted 8 lines

* If it is enabled then they are read-only; if the link
* is up they represent the negotiated link mode; if the link is down,
* the speed is 0, %SPEED_UNKNOWN or the highest enabled speed and
* @duplex is %DUPLEX_UNKNOWN or the best enabled duplex mode.

So, it seems that taprio is not following the API... I'd suggest either fixing taprio, or getting agreement to change the ethtool API.

How would you suggest rewriting the line above in taprio to make correct and robust use of the ethtool API?

Quoted 4 lines

--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up According to speedtest.net: 11.9Mbps down 500kbps up

Regards,
-Vladimir