Add support for AXI DMA controller on Milbeaut series
Subsystems (3)
v2 cover Add support for AXI DMA controller on Milbeaut series
From: Jassi Brar <[email protected]>
The following series adds AXI DMA (XDMAC) controller support on Milbeaut series. This controller is capable of only Mem<->MEM transfers. Number of channels is configurable {2,4,8}
Changes Since v1:
# Spelling mistake fix
Jassi Brar (2):
dt-bindings: milbeaut-m10v-xdmac: Add Socionext Milbeaut XDMAC
bindings
dmaengine: milbeaut-xdmac: Add XDMAC driver for Milbeaut platforms
.../bindings/dma/milbeaut-m10v-xdmac.txt | 24 + drivers/dma/Kconfig | 10 + drivers/dma/Makefile | 1 + drivers/dma/milbeaut-xdmac.c | 426 ++++++++++++++++++ 4 files changed, 461 insertions(+) create mode 100644 Documentation/devicetree/bindings/dma/milbeaut-m10v-xdmac.txt create mode 100644 drivers/dma/milbeaut-xdmac.c
Signature · 1 line
2.17.1
PATCH v2 1/2 dt-bindings: milbeaut-m10v-xdmac: Add Socionext Milbeaut XDMAC bindings
From: Jassi Brar <[email protected]>
Document the devicetree bindings for Socionext Milbeaut XDMAC controller. Controller only supports Mem->Mem transfers. Number of physical channels are determined by the number of irqs registered.
--- .../bindings/dma/milbeaut-m10v-xdmac.txt | 24 +++++++++++++++++++ 1 file changed, 24 insertions(+) create mode 100644 Documentation/devicetree/bindings/dma/milbeaut-m10v-xdmac.txt
Documentation/devicetree/bindings/dma/milbeaut-m10v-xdmac.txt new file +24 -0
@@ -0,0 +1,24 @@ +* Milbeaut AXI DMA Controller + +Milbeaut AXI DMA controller has only memory to memory transfer capability. + +* DMA controller + +Required property: +- compatible: Should be "socionext,milbeaut-m10v-xdmac" +- reg: Should contain DMA registers location and length. +- interrupts: Should contain all of the per-channel DMA interrupts. + Number of channels is configurable - 2, 4 or 8, so + the number of interrupts specified should be {2,4,8}. +- #dma-cells: Should be 1. + +Example: + xdmac0: dma-controller@1c250000 { + compatible = "socionext,milbeaut-m10v-xdmac"; + reg = <0x1c250000 0x1000>; + interrupts = <0 17 0x4>, + <0 18 0x4>, + <0 19 0x4>, + <0 20 0x4>; + #dma-cells = <1>; + };
Signature · 1 line
2.17.1
PATCH v2 2/2 dmaengine: milbeaut-xdmac: Add XDMAC driver for Milbeaut platforms
In reply to [email protected]From: Jassi Brar <[email protected]>
Driver for Socionext Milbeaut XDMAC controller. The controller only supports Mem-To-Mem transfers over upto 8 configurable channels.
--- drivers/dma/Kconfig | 10 + drivers/dma/Makefile | 1 + drivers/dma/milbeaut-xdmac.c | 426 +++++++++++++++++++++++++++++++++++ 3 files changed, 437 insertions(+) create mode 100644 drivers/dma/milbeaut-xdmac.c
drivers/dma/Kconfig +10 -0
@@ -358,6 +358,16 @@ config MILBEAUT_HDMAC Say yes here to support the Socionext Milbeaut HDMAC device. +config MILBEAUT_XDMAC + tristate "Milbeaut AXI DMA support" + depends on ARCH_MILBEAUT || COMPILE_TEST + depends on OF + select DMA_ENGINE + select DMA_VIRTUAL_CHANNELS + help + Say yes here to support the Socionext Milbeaut + XDMAC device. + config MMP_PDMA bool "MMP PDMA support" depends on ARCH_MMP || ARCH_PXA || COMPILE_TEST
drivers/dma/Makefile +1 -0
@@ -47,6 +47,7 @@ obj-$(CONFIG_INTEL_MIC_X100_DMA) += mic_x100_dma.o obj-$(CONFIG_K3_DMA) += k3dma.o obj-$(CONFIG_LPC18XX_DMAMUX) += lpc18xx-dmamux.o obj-$(CONFIG_MILBEAUT_HDMAC) += milbeaut-hdmac.o +obj-$(CONFIG_MILBEAUT_XDMAC) += milbeaut-xdmac.o obj-$(CONFIG_MMP_PDMA) += mmp_pdma.o obj-$(CONFIG_MMP_TDMA) += mmp_tdma.o obj-$(CONFIG_MOXART_DMA) += moxart-dma.o
drivers/dma/milbeaut-xdmac.c new file +426 -0
426 lines not on this page · raw message
Signature · 1 line
2.17.1