Add support for AHB DMA controller on Milbeaut series
Subsystems (3)
v3 cover Add support for AHB DMA controller on Milbeaut series
From: Jassi Brar <[email protected]>
The following series adds AHB DMA (HDMAC) controller support on Milbeaut series. This controller is capable of Mem<->MEM and DEV<->MEM transfer. But only DEV<->MEM is currently supported.
Changes since v2:
# Spelling mistake fix
# Bug fix prep_slave - made local copy of sgl
Jassi Brar (2):
dt-bindings: milbeaut-m10v-hdmac: Add Socionext Milbeaut HDMAC
bindings
dmaengine: milbeaut-hdmac: Add HDMAC driver for Milbeaut platforms
.../bindings/dma/milbeaut-m10v-hdmac.txt | 32 + drivers/dma/Kconfig | 10 + drivers/dma/Makefile | 1 + drivers/dma/milbeaut-hdmac.c | 583 ++++++++++++++++++ 4 files changed, 626 insertions(+) create mode 100644 Documentation/devicetree/bindings/dma/milbeaut-m10v-hdmac.txt create mode 100644 drivers/dma/milbeaut-hdmac.c
Signature · 1 line
2.17.1
PATCH v3 1/2 dt-bindings: milbeaut-m10v-hdmac: Add Socionext Milbeaut HDMAC bindings
From: Jassi Brar <[email protected]>
Document the devicetree bindings for Socionext Milbeaut HDMAC controller. Controller has upto 8 floating channels, that need a predefined slave-id to work from a set of slaves.
--- .../bindings/dma/milbeaut-m10v-hdmac.txt | 32 +++++++++++++++++++ 1 file changed, 32 insertions(+) create mode 100644 Documentation/devicetree/bindings/dma/milbeaut-m10v-hdmac.txt
Documentation/devicetree/bindings/dma/milbeaut-m10v-hdmac.txt new file +32 -0
@@ -0,0 +1,32 @@ +* Milbeaut AHB DMA Controller + +Milbeaut AHB DMA controller has transfer capability below. + - device to memory transfer + - memory to device transfer + +Required property: +- compatible: Should be "socionext,milbeaut-m10v-hdmac" +- reg: Should contain DMA registers location and length. +- interrupts: Should contain all of the per-channel DMA interrupts. + Number of channels is configurable - 2, 4 or 8, so + the number of interrupts specified should be {2,4,8}. +- #dma-cells: Should be 1. Specify the ID of the slave. +- clocks: Phandle to the clock used by the HDMAC module. + + +Example: + + hdmac1: dma-controller@1e110000 { + compatible = "socionext,milbeaut-m10v-hdmac"; + reg = <0x1e110000 0x10000>; + interrupts = <0 132 4>, + <0 133 4>, + <0 134 4>, + <0 135 4>, + <0 136 4>, + <0 137 4>, + <0 138 4>, + <0 139 4>; + #dma-cells = <1>; + clocks = <&dummy_clk>; + };
Signature · 1 line
2.17.1
PATCH v3 2/2 dmaengine: milbeaut-hdmac: Add HDMAC driver for Milbeaut platforms
In reply to [email protected]From: Jassi Brar <[email protected]>
Driver for Socionext Milbeaut HDMAC controller. The controller has upto 8 floating channels, that need a predefined slave-id to work from a set of slaves.
--- drivers/dma/Kconfig | 10 + drivers/dma/Makefile | 1 + drivers/dma/milbeaut-hdmac.c | 583 +++++++++++++++++++++++++++++++++++ 3 files changed, 594 insertions(+) create mode 100644 drivers/dma/milbeaut-hdmac.c
drivers/dma/Kconfig +10 -0
@@ -348,6 +348,16 @@ config MCF_EDMA minimal intervention from a host processor. This module can be found on Freescale ColdFire mcf5441x SoCs. +config MILBEAUT_HDMAC + tristate "Milbeaut AHB DMA support" + depends on ARCH_MILBEAUT || COMPILE_TEST + depends on OF + select DMA_ENGINE + select DMA_VIRTUAL_CHANNELS + help + Say yes here to support the Socionext Milbeaut + HDMAC device. + config MMP_PDMA bool "MMP PDMA support" depends on ARCH_MMP || ARCH_PXA || COMPILE_TEST
drivers/dma/Makefile +1 -0
@@ -46,6 +46,7 @@ obj-$(CONFIG_INTEL_IOP_ADMA) += iop-adma.o obj-$(CONFIG_INTEL_MIC_X100_DMA) += mic_x100_dma.o obj-$(CONFIG_K3_DMA) += k3dma.o obj-$(CONFIG_LPC18XX_DMAMUX) += lpc18xx-dmamux.o +obj-$(CONFIG_MILBEAUT_HDMAC) += milbeaut-hdmac.o obj-$(CONFIG_MMP_PDMA) += mmp_pdma.o obj-$(CONFIG_MMP_TDMA) += mmp_tdma.o obj-$(CONFIG_MOXART_DMA) += moxart-dma.o
drivers/dma/milbeaut-hdmac.c new file +583 -0
583 lines not on this page · raw message
Signature · 1 line
2.17.1