dt-bindings: ASoC: Add tas2770 smart PA dt bindings
PATCH v6 1/1 dt-bindings: ASoC: Add tas2770 smart PA dt bindings
From: Frank Shi <[email protected]>
Add tas2770 smart PA dt bindings
--- .../devicetree/bindings/sound/tas2770.txt | 37 ++++++++++++++++++++++ 1 file changed, 37 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/tas2770.txt
Documentation/devicetree/bindings/sound/tas2770.txt new file +37 -0
@@ -0,0 +1,37 @@ +Texas Instruments TAS2770 Smart PA + +The TAS2770 is a mono, digital input Class-D audio amplifier optimized for +efficiently driving high peak power into small loudspeakers. +Integrated speaker voltage and current sense provides for +real time monitoring of loudspeaker behavior. + +Required properties: + + - compatible: - Should contain "ti,tas2770". + - reg: - The i2c address. Should contain <0x4c>, <0x4d>,<0x4e>, or <0x4f>. + - #address-cells - Should be <1>. + - #size-cells - Should be <0>. + - ti,asi-format: - Sets TDM RX capture edge. 0->Rising; 1->Falling. + - ti,imon-slot-no:- TDM TX current sense time slot. + - ti,vmon-slot-no:- TDM TX voltage sense time slot. + +Optional properties: + +- interrupt-parent: the phandle to the interrupt controller which provides + the interrupt. +- interrupts: interrupt specification for data-ready. + +Examples: + + tas2770@4c { + compatible = "ti,tas2770"; + reg = <0x4c>; + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <&msm_gpio>; + interrupts = <97 0>; + ti,asi-format = <0>; + ti,imon-slot-no = <0>; + ti,vmon-slot-no = <2>; + }; +
Signature · 1 line
2.7.4
PATCH v6 1/1 tas2770: add tas2770 smart PA kernel driver
From: Frank Shi <[email protected]>
add tas2770 smart PA kernel driver
--- sound/soc/codecs/Kconfig | 5 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/tas2770.c | 814 +++++++++++++++++++++++++++++++++++++++++++++ sound/soc/codecs/tas2770.h | 164 +++++++++ 4 files changed, 985 insertions(+) create mode 100644 sound/soc/codecs/tas2770.c create mode 100644 sound/soc/codecs/tas2770.h
sound/soc/codecs/Kconfig +5 -0
@@ -111,6 +111,7 @@ config SND_SOC_ALL_CODECS select SND_SOC_STAC9766 if SND_SOC_AC97_BUS select SND_SOC_STI_SAS select SND_SOC_TAS2552 if I2C + select SND_SOC_TAS2770 if I2C select SND_SOC_TAS5086 if I2C select SND_SOC_TAS571X if I2C select SND_SOC_TFA9879 if I2C
@@ -652,6 +653,10 @@ config SND_SOC_TAS2552 tristate "Texas Instruments TAS2552 Mono Audio amplifier" depends on I2C +config SND_SOC_TAS2770 + tristate "Texas Instruments TAS2770 speaker amplifier" + depends on I2C + config SND_SOC_TAS5086 tristate "Texas Instruments TAS5086 speaker amplifier" depends on I2C
sound/soc/codecs/Makefile +2 -0
@@ -116,6 +116,7 @@ snd-soc-stac9766-objs := stac9766.o snd-soc-sti-sas-objs := sti-sas.o snd-soc-tas5086-objs := tas5086.o snd-soc-tas571x-objs := tas571x.o +snd-soc-tas2770-objs := tas2770.o snd-soc-tfa9879-objs := tfa9879.o snd-soc-tlv320aic23-objs := tlv320aic23.o snd-soc-tlv320aic23-i2c-objs := tlv320aic23-i2c.o
@@ -332,6 +333,7 @@ obj-$(CONFIG_SND_SOC_STI_SAS) += snd-soc-sti-sas.o obj-$(CONFIG_SND_SOC_TAS2552) += snd-soc-tas2552.o obj-$(CONFIG_SND_SOC_TAS5086) += snd-soc-tas5086.o obj-$(CONFIG_SND_SOC_TAS571X) += snd-soc-tas571x.o +obj-$(CONFIG_SND_SOC_TAS2770) += snd-soc-tas2770.o obj-$(CONFIG_SND_SOC_TFA9879) += snd-soc-tfa9879.o obj-$(CONFIG_SND_SOC_TLV320AIC23) += snd-soc-tlv320aic23.o obj-$(CONFIG_SND_SOC_TLV320AIC23_I2C) += snd-soc-tlv320aic23-i2c.o
sound/soc/codecs/tas2770.c new file +814 -0
814 lines not on this page · raw message
sound/soc/codecs/tas2770.h new file +164 -0
164 lines not on this page · raw message
Signature · 1 line
2.7.4
Mark Brown
maintainerRe: [PATCH v6] tas2770: add tas2770 smart PA kernel driver
Quoted 8 lines · On Wed, Sep 18, 2019 at 04:28:13PM +0800, [email protected] wrote:
sound/soc/codecs/tas2770.c new file +8
-0+static int tas2770_codec_suspend (struct snd_soc_component *component) +{ +int ret; + + ret =snd_soc_component_update_bits (component, +TAS2770_PWR_CTRL , +TAS2770_PWR_CTRL_MASK , +TAS2770_PWR_CTRL_SHUTDOWN );
sound/soc/codecs/tas2770.c line 94
Quoted 10 lines
sound/soc/codecs/tas2770.c new file +10
-0+if (ret) { +snd_soc_component_update_bits (component, +TAS2770_PWR_CTRL , +TAS2770_PWR_CTRL_MASK , +TAS2770_PWR_CTRL_ACTIVE ); +return -EINVAL ; + } + +return 0 ; +}
This error handling is a bit weird, if the write failed usually it's best to leave things as they are rather than retrying the write. You should also pass back the error code you got from the I/O rather than overwriting it with -EINVAL since that helps people diagnose problems.
sound/soc/codecs/tas2770.c line 264
Quoted 2 lines
sound/soc/codecs/tas2770.c new file +2
-0+static int tas2770_set_samplerate (struct tas2770_priv *tas2770, +int samplerate)
The indentation on the second line here is really weird, it's not aligned with anything.
sound/soc/codecs/tas2770.c line 495
Quoted 7 lines
sound/soc/codecs/tas2770.c new file +7
-0+switch (slot_width) { +case 16 : + ret =snd_soc_component_update_bits (component, +TAS2770_TDM_CFG_REG2 , +TAS2770_TDM_CFG_REG2_RXS_MASK , +TAS2770_TDM_CFG_REG2_RXS_16BITS ); +break ;
The indentation of the break statements here is still off.
sound/soc/codecs/tas2770.c line 583
Quoted 7 lines
sound/soc/codecs/tas2770.c new file +7
-0+static const struct snd_kcontrol_new tas2770_snd_controls[] = { +SOC_SINGLE_TLV ("Playback Volume" ,TAS2770_PLAY_CFG_REG2 , +0 ,TAS2770_PLAY_CFG_REG2_VMAX ,1 , + tas2770_playback_volume), +SOC_SINGLE_TLV ("Amp Output Gain" ,TAS2770_PLAY_CFG_REG0 , +0 ,0x14 ,0 , + tas2770_digital_tlv),
Volume controls should still have names endinf in Volume as covered in control-names.rst.
Please don't ignore review comments, people are generally making them for a reason and are likely to have the same concerns if issues remain unaddressed. Having to repeat the same comments can get repetitive and make people question the value of time spent reviewing. If you disagree with the review comments that's fine but you need to reply and discuss your concerns so that the reviewer can understand your decisions.