Skip to contentSkip to conversation

DDC on Thinkpad x220

DISCUSSION Pavel Machek 2 participants 3 messages Sep 30, 2019 – Oct 1, 2019

lore
Share & tools
lore
#0 lore raw

Hi!

Thinkpad X220 should be new enough machine to talk DDC to the monitors, right? And my monitor has DDC enable/disable in the menu, so it should support it, too...

But I don't have /dev/i2c* and did not figure out how to talk to the monitor. Is the support there in the kernel? What do I need to enable it?

lspci says:

00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)

Thanks,
Pavel

Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

#1 lore raw
Quoted 9 lines · Pavel Machek

Hi!

Thinkpad X220 should be new enough machine to talk DDC to the monitors, right? And my monitor has DDC enable/disable in the menu, so it should support it, too...

But I don't have /dev/i2c* and did not figure out how to talk to the monitor. Is the support there in the kernel? What do I need to enable it?

# modprobe i2c-dev

BR,
Jani.

Signature · 1 line
Jani Nikula, Intel Open Source Graphics Center
#2 lore raw
Quoted 7 lines · Jani Nikula
Quoted 6 lines · Pavel Machek

Hi!

Thinkpad X220 should be new enough machine to talk DDC to the monitors, right? And my monitor has DDC enable/disable in the menu, so it should support it, too...

Quoted 5 lines
Quoted 3 lines

But I don't have /dev/i2c* and did not figure out how to talk to the monitor. Is the support there in the kernel? What do I need to enable it?

# modprobe i2c-dev

Thanks!

I enabled I2C_CHARDEV, and installed ddccontrol:

c ddccontrol - program to control monitor

I can read parameters of Dell monitor on VGA:

sudo ddccontrol dev:/dev/i2c-1 -c -d
/usr/share/ddccontrol-db/monitor/DELA013.xml
Control 0x10: +/79/100 [???] -- brightness
Control 0x12: +/63/100 [???] -- contrast

Unfortunately the Fujitsu monitor does not seem to communicate. Fujitsu is my main monitor :-(.

pavel@duo:~$ sudo ddccontrol dev:/dev/i2c-4 -c -d
ddccontrol version 0.4.2
Copyright 2004-2005 Oleg I. Vdovikin ([email protected])
Copyright 2004-2006 Nicolas Boichat ([email protected])
This program comes with ABSOLUTELY NO WARRANTY.
You may redistribute copies of this program under the terms of the GNU
General Public License.

Reading EDID and initializing DDC/CI at bus dev:/dev/i2c-4... ioctl(): No such device or address
ioctl returned -1
ioctl(): No such device or address
ioctl returned -1
ioctl(): No such device or address
ioctl returned -1
I/O warning : failed to load external entity "/usr/share/ddccontrol-db/monitor/FUS080A.xml" Document not parsed successfully.
ioctl(): No such device or address
ioctl returned -1

DDC/CI at dev:/dev/i2c-4 is unusable (-1).
If your graphics card need it, please check all the required kernel modules are loaded (i2c-dev, and your framebuffer driver).

Any further hints?

Thanks and best regards,
Pavel

Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx