DDC on Thinkpad x220
Hi!
Thinkpad X220 should be new enough machine to talk DDC to the monitors, right? And my monitor has DDC enable/disable in the menu, so it should support it, too...
But I don't have /dev/i2c* and did not figure out how to talk to the monitor. Is the support there in the kernel? What do I need to enable it?
lspci says:
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)
Thanks,
Pavel
Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 9 lines · Pavel Machek
Hi!
Thinkpad X220 should be new enough machine to talk DDC to the monitors, right? And my monitor has DDC enable/disable in the menu, so it should support it, too...
But I don't have
/dev/i2c*and did not figure out how to talk to the monitor. Is the support there in the kernel? What do I need to enable it?
# modprobe i2c-dev
BR,
Jani.
Signature · 1 line
Jani Nikula, Intel Open Source Graphics Center
Quoted 7 lines · Jani Nikula
Quoted 6 lines · Pavel Machek
Hi!
Thinkpad X220 should be new enough machine to talk DDC to the monitors, right? And my monitor has DDC enable/disable in the menu, so it should support it, too...
Quoted 5 lines
Quoted 3 lines
But I don't have
/dev/i2c*and did not figure out how to talk to the monitor. Is the support there in the kernel? What do I need to enable it?# modprobe i2c-dev
Thanks!
I enabled I2C_CHARDEV, and installed ddccontrol:
c ddccontrol - program to control monitor
I can read parameters of Dell monitor on VGA:
sudo ddccontrol dev:/dev/i2c-1 -c -d/usr/share/ddccontrol-db/monitor/DELA013.xml
Control 0x10: +/79/100 [???] -- brightness
Control 0x12: +/63/100 [???] -- contrast
Unfortunately the Fujitsu monitor does not seem to communicate. Fujitsu is my main monitor :-(.
pavel@duo:~$ sudo ddccontrol dev:/dev/i2c-4 -c -d ddccontrol version 0.4.2 Copyright 2004-2005 Oleg I. Vdovikin ([email protected]) Copyright 2004-2006 Nicolas Boichat ([email protected]) This program comes with ABSOLUTELY NO WARRANTY. You may redistribute copies of this program under the terms of the GNU General Public License.
Reading EDID and initializing DDC/CI at bus dev:/dev/i2c-4... ioctl(): No such device or address
ioctl returned -1ioctl(): No such device or address
ioctl returned -1ioctl(): No such device or address
ioctl returned -1
I/O warning : failed to load external entity "/usr/share/ddccontrol-db/monitor/FUS080A.xml" Document not parsed successfully.ioctl(): No such device or address
ioctl returned -1
DDC/CI at dev:/dev/i2c-4 is unusable (-1).
If your graphics card need it, please check all the required kernel modules are loaded (i2c-dev, and your framebuffer driver).
Any further hints?
Thanks and best regards,
Pavel
Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx