ptp: fix typo of "mechanism" in Kconfig help text
Subsystems (7)
PATCH 1/1 ptp: fix typo of "mechanism" in Kconfig help text
Fix typo s/mechansim/mechanism/
--- drivers/ptp/Kconfig | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/ptp/Kconfig +2 -2
@@ -97,8 +97,8 @@ config PTP_1588_CLOCK_PCH help This driver adds support for using the PCH EG20T as a PTP clock. The hardware supports time stamping of PTP packets - when using the end-to-end delay (E2E) mechansim. The peer - delay mechansim (P2P) is not supported. + when using the end-to-end delay (E2E) mechanism. The peer + delay mechanism (P2P) is not supported. This clock is only useful if your PTP programs are getting hardware time stamps on the PTP Ethernet packets using the
Signature · 1 line
2.23.0
PATCH 1/1 staging: rtl8723bs: fix typo of "mechanism" in comment
Fix typo s/mechansim/mechanism/
--- drivers/staging/rtl8723bs/hal/hal_btcoex.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/staging/rtl8723bs/hal/hal_btcoex.c +1 -1
@@ -1315,7 +1315,7 @@ void EXhalbtcoutsrc_DisplayBtCoexInfo(PBTC_COEXIST pBtCoexist)/* * Description: -*Run BT-Coexist mechansim or not +*Run BT-Coexist mechanism or not * */ void hal_btcoex_SetBTCoexist (struct adapter *padapter,u8 bBtExist)
Signature · 1 line
2.23.0
PATCH 1/1 net: stmmac: add flexible PPS to dwmac 4.10a
In reply to Antonio BorneoAll the registers and the functionalities used in the callback dwmac5_flex_pps_config() are common between dwmac 4.10a [1] and 5.00a [2].
Reuse the same callback for dwmac 4.10a too.
Tested on STM32MP15x, based on dwmac 4.10a.
[1] DWC Ethernet QoS Databook 4.10a October 2014
[2] DWC Ethernet QoS Databook 5.00a September 2017
--- drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c | 1 + 1 file changed, 1 insertion(+)
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c +1 -0
@@ -864,6 +864,7 @@ const struct stmmac_ops dwmac410_ops = { .pcs_get_adv_lp = dwmac4_get_adv_lp, .debug = dwmac4_debug, .set_filter = dwmac4_set_filter, + .flex_pps_config = dwmac5_flex_pps_config, .set_mac_loopback = dwmac4_set_mac_loopback, .update_vlan_hash = dwmac4_update_vlan_hash, .sarc_configure = dwmac4_sarc_configure,
Signature · 1 line
2.23.0
Jakub Kicinski
AppliedRe: [PATCH] net: stmmac: add flexible PPS to dwmac 4.10a
Quoted 4 lines · Antonio Borneo
All the registers and the functionalities used in the callback
dwmac5_flex_pps_config()are common between dwmac 4.10a [1] and 5.00a [2].
Quoted 8 lines
Reuse the same callback for dwmac 4.10a too.
Tested on STM32MP15x, based on dwmac 4.10a.
[1] DWC Ethernet QoS Databook 4.10a October 2014
[2] DWC Ethernet QoS Databook 5.00a September 2017Signed-off-by Antonio Borneo <[email protected]>
Applied to net-next.
Re: [PATCH] net: stmmac: add flexible PPS to dwmac 4.10a
Hello Jakub,
Quoted 7 lines · Jakub Kicinski
Quoted 6 lines · Antonio Borneo
All the registers and the functionalities used in the callback
dwmac5_flex_pps_config()are common between dwmac 4.10a [1] and 5.00a [2].Reuse the same callback for dwmac 4.10a too.
Quoted 8 lines
Quoted 6 lines
Tested on STM32MP15x, based on dwmac 4.10a.
[1] DWC Ethernet QoS Databook 4.10a October 2014
[2] DWC Ethernet QoS Databook 5.00a September 2017Signed-off-by Antonio Borneo <[email protected]>Applied to net-next.
This patch seems to have been fuzzily applied at the wrong location. The diff describes extension of dwmac 4.10a and so does the @@ line:
@@ -864,6 +864,7 @@ const struct stmmac_ops dwmac410_ops = {The patch was applied mainline as 757926247836 ("net: stmmac: add flexible PPS to dwmac 4.10a"), but it extends dwmac4_ops instead:
@@ -938,6 +938,7 @@ const struct stmmac_ops dwmac4_ops = {I don't know if dwmac4 actually supports FlexPPS, so I think it's better to be on the safe side and revert 757926247836 and add the change for the correct variant.
Cheers,
Ahmad
Signature · 4 lines
Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Re: [PATCH] net: stmmac: add flexible PPS to dwmac 4.10a
Quoted 24 lines · Ahmad Fatoum
Hello Jakub,
Quoted 7 lines · Jakub Kicinski
Quoted 6 lines · Antonio Borneo
All the registers and the functionalities used in the callback
dwmac5_flex_pps_config()are common between dwmac 4.10a [1] and 5.00a [2].Reuse the same callback for dwmac 4.10a too.
Quoted 8 lines
Quoted 6 lines
Tested on STM32MP15x, based on dwmac 4.10a.
[1] DWC Ethernet QoS Databook 4.10a October 2014
[2] DWC Ethernet QoS Databook 5.00a September 2017Signed-off-by Antonio Borneo <[email protected]>Applied to net-next.
This patch seems to have been fuzzily applied at the wrong location. The diff describes extension of dwmac 4.10a and so does the @@ line:
@@ -864,6 +864,7 @@ const struct
stmmac_opsdwmac410_ops= {
Quoted 8 lines
The patch was applied mainline as 757926247836 ("net: stmmac: add flexible PPS to dwmac 4.10a"), but it extends
dwmac4_opsinstead:@@ -938,6 +938,7 @@ const struct
stmmac_opsdwmac4_ops= {I don't know if dwmac4 actually supports FlexPPS, so I think it's better to be on the safe side and revert 757926247836 and add the change for the correct variant.
Agree,
the patch get applied to the wrong place!
Antonio
Quoted 5 lines
Cheers,
Ahmad
Jakub Kicinski
maintainerRe: [PATCH] net: stmmac: add flexible PPS to dwmac 4.10a
Quoted 26 lines · On Tue, 24 Nov 2020 15:23:27 +0100 Antonio Borneo wrote:
Quoted 25 lines · Ahmad Fatoum
Quoted 7 lines · Jakub Kicinski
Quoted 6 lines · Antonio Borneo
All the registers and the functionalities used in the callback
dwmac5_flex_pps_config()are common between dwmac 4.10a [1] and 5.00a [2].Reuse the same callback for dwmac 4.10a too.
Quoted 8 lines
Quoted 6 lines
Tested on STM32MP15x, based on dwmac 4.10a.
[1] DWC Ethernet QoS Databook 4.10a October 2014
[2] DWC Ethernet QoS Databook 5.00a September 2017Signed-off-by Antonio Borneo <[email protected]>Applied to net-next.
This patch seems to have been fuzzily applied at the wrong location. The diff describes extension of dwmac 4.10a and so does the @@ line:
@@ -864,6 +864,7 @@ const struct
stmmac_opsdwmac410_ops= {The patch was applied mainline as 757926247836 ("net: stmmac: add flexible PPS to dwmac 4.10a"), but it extends
dwmac4_opsinstead:
Quoted 8 lines
Quoted 5 lines
@@ -938,6 +938,7 @@ const struct
stmmac_opsdwmac4_ops= {I don't know if dwmac4 actually supports FlexPPS, so I think it's better to be on the safe side and revert 757926247836 and add the change for the correct variant.
Agree,
the patch get applied to the wrong place!
:-o
This happens sometimes with stable backports but I've never seen it happen working on "current" branches.
Sorry about that!
Would you mind sending the appropriate patches? I can do the revert if you prefer, but since you need to send the fix anyway..
Re: [PATCH] net: stmmac: add flexible PPS to dwmac 4.10a
Quoted 38 lines · Jakub Kicinski
Quoted 26 lines · On Tue, 24 Nov 2020 15:23:27 +0100 Antonio Borneo wrote:
Quoted 25 lines · Ahmad Fatoum
Quoted 7 lines · Jakub Kicinski
Quoted 6 lines · Antonio Borneo
All the registers and the functionalities used in the callback
dwmac5_flex_pps_config()are common between dwmac 4.10a [1] and 5.00a [2].Reuse the same callback for dwmac 4.10a too.
Quoted 8 lines
Quoted 6 lines
Tested on STM32MP15x, based on dwmac 4.10a.
[1] DWC Ethernet QoS Databook 4.10a October 2014
[2] DWC Ethernet QoS Databook 5.00a September 2017Signed-off-by Antonio Borneo <[email protected]>Applied to net-next.
This patch seems to have been fuzzily applied at the wrong location. The diff describes extension of dwmac 4.10a and so does the @@ line:
@@ -864,6 +864,7 @@ const struct
stmmac_opsdwmac410_ops= {The patch was applied mainline as 757926247836 ("net: stmmac: add flexible PPS to dwmac 4.10a"), but it extends
dwmac4_opsinstead:Quoted 8 lines
Quoted 5 lines
@@ -938,6 +938,7 @@ const struct
stmmac_opsdwmac4_ops= {I don't know if dwmac4 actually supports FlexPPS, so I think it's better to be on the safe side and revert 757926247836 and add the change for the correct variant.
Agree,
the patch get applied to the wrong place!:-o
Quoted 7 lines
This happens sometimes with stable backports but I've never seen it happen working on "current" branches.
Sorry about that!
Would you mind sending the appropriate patches? I can do the revert if you prefer, but since you need to send the fix anyway..
You mean sending two patches one for revert and one to re-apply the code? Or a single patch for the fix?
Antonio
Jakub Kicinski
maintainerRe: [PATCH] net: stmmac: add flexible PPS to dwmac 4.10a
Quoted 42 lines · On Tue, 24 Nov 2020 19:27:03 +0100 Antonio Borneo wrote:
Quoted 41 lines · Jakub Kicinski
Quoted 26 lines · On Tue, 24 Nov 2020 15:23:27 +0100 Antonio Borneo wrote:
Quoted 25 lines · Ahmad Fatoum
Quoted 7 lines · Jakub Kicinski
Quoted 6 lines · Antonio Borneo
All the registers and the functionalities used in the callback
dwmac5_flex_pps_config()are common between dwmac 4.10a [1] and 5.00a [2].Reuse the same callback for dwmac 4.10a too.
Quoted 8 lines
Quoted 6 lines
Tested on STM32MP15x, based on dwmac 4.10a.
[1] DWC Ethernet QoS Databook 4.10a October 2014
[2] DWC Ethernet QoS Databook 5.00a September 2017Signed-off-by Antonio Borneo <[email protected]>Applied to net-next.
This patch seems to have been fuzzily applied at the wrong location. The diff describes extension of dwmac 4.10a and so does the @@ line:
@@ -864,6 +864,7 @@ const struct
stmmac_opsdwmac410_ops= {The patch was applied mainline as 757926247836 ("net: stmmac: add flexible PPS to dwmac 4.10a"), but it extends
dwmac4_opsinstead:Quoted 8 lines
Quoted 5 lines
@@ -938,6 +938,7 @@ const struct
stmmac_opsdwmac4_ops= {I don't know if dwmac4 actually supports FlexPPS, so I think it's better to be on the safe side and revert 757926247836 and add the change for the correct variant.
Agree,
the patch get applied to the wrong place!:-o
This happens sometimes with stable backports but I've never seen it happen working on "current" branches.
Quoted 7 lines
Quoted 4 lines
Sorry about that!
Would you mind sending the appropriate patches? I can do the revert if you prefer, but since you need to send the fix anyway..
You mean sending two patches one for revert and one to re-apply the code? Or a single patch for the fix?
Either way is fine by me. If I was doing it - I'd probably send just one patch, but if you prefer to revert first - nothing wrong with that.
Re: [PATCH] net: stmmac: add flexible PPS to dwmac 4.10a
In reply to Ahmad FatoumTo += Jakub's new address
Quoted 37 lines · Ahmad Fatoum
Hello Jakub,
Quoted 7 lines · Jakub Kicinski
Quoted 6 lines · Antonio Borneo
All the registers and the functionalities used in the callback
dwmac5_flex_pps_config()are common between dwmac 4.10a [1] and 5.00a [2].Reuse the same callback for dwmac 4.10a too.
Quoted 8 lines
Quoted 6 lines
Tested on STM32MP15x, based on dwmac 4.10a.
[1] DWC Ethernet QoS Databook 4.10a October 2014
[2] DWC Ethernet QoS Databook 5.00a September 2017Signed-off-by Antonio Borneo <[email protected]>Applied to net-next.
This patch seems to have been fuzzily applied at the wrong location. The diff describes extension of dwmac 4.10a and so does the @@ line:
@@ -864,6 +864,7 @@ const struct stmmac_ops dwmac410_ops = {The patch was applied mainline as 757926247836 ("net: stmmac: add flexible PPS to dwmac 4.10a"), but it extends
dwmac4_opsinstead:@@ -938,6 +938,7 @@ const struct stmmac_ops dwmac4_ops = {I don't know if dwmac4 actually supports FlexPPS, so I think it's better to be on the safe side and revert 757926247836 and add the change for the correct variant.
Cheers,
Ahmad
Signature · 4 lines
Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
PATCH 1/1 net: stmmac: fix incorrect merge of patch upstream
In reply to Ahmad FatoumCommit 757926247836 ("net: stmmac: add flexible PPS to dwmac 4.10a") was intended to modify the struct dwmac410_ops, but it got somehow badly merged and modified the struct dwmac4_ops.
Revert the modification in struct dwmac4_ops and re-apply it properly in struct dwmac410_ops.
---
To: Alexandre Torgue <[email protected]>
To: Jose Abreu <[email protected]>
To: "David S. Miller" <[email protected]>
To: Jakub Kicinski <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
In-Reply-To: <[email protected]>
--- drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c +1 -1
@@ -1171,7 +1171,6 @@ const struct stmmac_ops dwmac4_ops = { .pcs_get_adv_lp = dwmac4_get_adv_lp, .debug = dwmac4_debug, .set_filter = dwmac4_set_filter, - .flex_pps_config = dwmac5_flex_pps_config, .set_mac_loopback = dwmac4_set_mac_loopback, .update_vlan_hash = dwmac4_update_vlan_hash, .sarc_configure = dwmac4_sarc_configure,
@@ -1213,6 +1212,7 @@ const struct stmmac_ops dwmac410_ops = { .pcs_get_adv_lp = dwmac4_get_adv_lp, .debug = dwmac4_debug, .set_filter = dwmac4_set_filter, + .flex_pps_config = dwmac5_flex_pps_config, .set_mac_loopback = dwmac4_set_mac_loopback, .update_vlan_hash = dwmac4_update_vlan_hash, .sarc_configure = dwmac4_sarc_configure,
base-commit: 9bd2702d292cb7b565b09e949d30288ab7a26d51
Signature · 1 line
2.29.2
Re: [PATCH] net: stmmac: fix incorrect merge of patch upstream
Hello,
Quoted 9 lines · Antonio Borneo
Commit 757926247836 ("net: stmmac: add flexible PPS to dwmac 4.10a") was intended to modify the struct
dwmac410_ops, but it got somehow badly merged and modified the structdwmac4_ops.Revert the modification in struct
dwmac4_opsand re-apply it properly in structdwmac410_ops.Fixes 757926247836 ("net: stmmac: add flexible PPS to dwmac 4.10a")Cc [email protected] # v5.6+
I don't think extension of dwmac410_ops should be backported to stable. It's a new feature and should go into net-next like any other. The fix that could be backported is reverting the unintentional change of dwmac4.
Cheers,
Ahmad
Quoted 40 lines
Signed-off-by Antonio Borneo <[email protected]>Reported-by Ahmad Fatoum <[email protected]>---
To: Alexandre Torgue <[email protected]>
To: Jose Abreu <[email protected]>
To: "David S. Miller" <[email protected]>
To: Jakub Kicinski <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
In-Reply-To: <[email protected]>--- drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c +1
-1@@ -1171,7 +1171,6 @@ const struct stmmac_ops dwmac4_ops = { .pcs_get_adv_lp = dwmac4_get_adv_lp, .debug = dwmac4_debug, .set_filter = dwmac4_set_filter, - .flex_pps_config = dwmac5_flex_pps_config, .set_mac_loopback = dwmac4_set_mac_loopback, .update_vlan_hash = dwmac4_update_vlan_hash, .sarc_configure = dwmac4_sarc_configure,@@ -1213,6 +1212,7 @@ const struct stmmac_ops dwmac410_ops = { .pcs_get_adv_lp = dwmac4_get_adv_lp, .debug = dwmac4_debug, .set_filter = dwmac4_set_filter, + .flex_pps_config = dwmac5_flex_pps_config, .set_mac_loopback = dwmac4_set_mac_loopback, .update_vlan_hash = dwmac4_update_vlan_hash, .sarc_configure = dwmac4_sarc_configure,base-commit:
9bd2702d292cb7b565b09e949d30288ab7a26d51
Signature · 4 lines
Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Re: [PATCH] net: stmmac: fix incorrect merge of patch upstream
In reply to Antonio BorneoQuoted 11 lines · On Tue, 24 Nov 2020 23:37:29 +0100 Antonio Borneo wrote:
Commit 757926247836 ("net: stmmac: add flexible PPS to dwmac 4.10a") was intended to modify the struct
dwmac410_ops, but it got somehow badly merged and modified the structdwmac4_ops.Revert the modification in struct
dwmac4_opsand re-apply it properly in structdwmac410_ops.Fixes 757926247836 ("net: stmmac: add flexible PPS to dwmac 4.10a")Cc [email protected] # v5.6+Signed-off-by Antonio Borneo <[email protected]>Reported-by Ahmad Fatoum <[email protected]>
Applied, and queued for 5.9 (all other 5.5+ branches are EOL by now).
Thanks!
PATCH 1/1 net: stmmac: fix length of PTP clock's name string
In reply to Antonio BorneoThe field "name" in struct ptp_clock_info has a fixed size of 16 chars and is used as zero terminated string by clock_name_show() in drivers/ptp/ptp_sysfs.c
The current initialization value requires 17 chars to fit also the null termination, and this causes overflow to the next bytes in the struct when the string is read as null terminated:
hexdump -C /sys/class/ptp/ptp0/clock_name 00000000 73 74 6d 6d 61 63 5f 70 74 70 5f 63 6c 6f 63 6b |stmmac_ptp_clock| 00000010 a0 ac b9 03 0a |.....|
where the extra 4 bytes (excluding the newline) after the string represent the integer 0x03b9aca0 = 62500000 assigned to the field "max_adj" that follows "name" in the same struct.
There is no strict requirement for the "name" content and in the comment in ptp_clock_kernel.h it's reported it should just be 'A short "friendly name" to identify the clock'.
Replace it with "stmmac ptp".
--- drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c +1 -1
@@ -164,7 +164,7 @@ static int stmmac_enable(struct ptp_clock_info *ptp,/* structure describing a PTP hardware clock */ static struct ptp_clock_info stmmac_ptp_clock_ops = { .owner =THIS_MODULE , - .name ="stmmac_ptp_clock" , + .name ="stmmac ptp" , .max_adj =62500000 , .n_alarm =0 , .n_ext_ts =0 ,
Signature · 1 line
2.23.0
Jakub Kicinski
AppliedRe: [PATCH] net: stmmac: fix length of PTP clock's name string
Quoted 13 lines · Antonio Borneo
The field "name" in struct
ptp_clock_infohas a fixed size of 16 chars and is used as zero terminated string byclock_name_show()indrivers/ptp/ptp_sysfs.c
The current initialization value requires 17 chars to fit also the null termination, and this causes overflow to the next bytes in the struct when the string is read as null terminated:hexdump -C /sys/class/ptp/ptp0/clock_name 00000000 73 74 6d 6d 61 63 5f 70 74 70 5f 63 6c 6f 63 6b |stmmac_ptp_clock| 00000010 a0 ac b9 03 0a |.....|where the extra 4 bytes (excluding the newline) after the string represent the integer
0x03b9aca0= 62500000 assigned to the field "max_adj" that follows "name" in the same struct.
Quoted 7 lines
There is no strict requirement for the "name" content and in the comment in
ptp_clock_kernel.hit's reported it should just be 'A short "friendly name" to identify the clock'.
Replace it with "stmmac ptp".Signed-off-by Antonio Borneo <[email protected]>Fixes 92ba6888510c ("stmmac: add the support for PTP hw clock driver")
Applied to net, queued for stable.
For future submissions please indicate the target tree. Networking fixes should go to the net tree and have [PATCH net] in the subject, while normal patches such as new features and clean ups should be tagged as [PATCH net-next].
PATCH 1/1 net: stmmac: fix disabling flexible PPS output
In reply to Antonio BorneoAccordingly to Synopsys documentation [1] and [2], when bit PPSEN0 in register MAC_PPS_CONTROL is set it selects the functionality command in the same register, otherwise selects the functionality control.
Command functionality is required to either enable (command 0x2) and disable (command 0x5) the flexible PPS output, but the bit PPSEN0 is currently set only for enabling.
Set the bit PPSEN0 to properly disable flexible PPS output.
Tested on STM32MP15x, based on dwmac 4.10a.
[1] DWC Ethernet QoS Databook 4.10a October 2014
[2] DWC Ethernet QoS Databook 5.00a September 2017
--- drivers/net/ethernet/stmicro/stmmac/dwmac5.c | 1 + 1 file changed, 1 insertion(+)
drivers/net/ethernet/stmicro/stmmac/dwmac5.c +1 -0
@@ -515,6 +515,7 @@ int dwmac5_flex_pps_config(void __iomem *ioaddr, int index,if (!enable) { val |=PPSCMDx (index,0x5 ); + val |=PPSEN0 ;writel (val, ioaddr +MAC_PPS_CONTROL );return 0 ; }
Signature · 1 line
2.23.0
Jakub Kicinski
AppliedRe: [PATCH] net: stmmac: fix disabling flexible PPS output
Quoted 10 lines · Antonio Borneo
Accordingly to Synopsys documentation [1] and [2], when bit PPSEN0 in register
MAC_PPS_CONTROLis set it selects the functionality command in the same register, otherwise selects the functionality control.
Command functionality is required to either enable (command0x2) and disable (command0x5) the flexible PPS output, but the bit PPSEN0 is currently set only for enabling.Set the bit PPSEN0 to properly disable flexible PPS output.
Quoted 7 lines
Tested on STM32MP15x, based on dwmac 4.10a.
[1] DWC Ethernet QoS Databook 4.10a October 2014
[2] DWC Ethernet QoS Databook 5.00a September 2017Signed-off-by Antonio Borneo <[email protected]>Fixes 9a8a02c9d46d ("net: stmmac: Add Flexible PPS support")
Applied to net, queued for stable.
From: Antonio Borneo <[email protected]>
Date: Mon, 7 Oct 2019 17:43:02 +0200
Quoted 3 lines
Fix typo s/mechansim/mechanism/
Signed-off-by Antonio Borneo <[email protected]>
Applied, thank you.