Skip to contentSkip to conversation

imx: support for conga-QMX8 board

PATCH Superseded Oliver Graute 1 participant 2 messages Oct 10, 2019

Subsystems (3)

v1 of 7 Superseded Latest is v7 →

lore
Share & tools
lore
#0 lore raw

cover imx: support for conga-QMX8 board

Hello list,

this patch adds support for the congatec QMX8 Qseven board.

Best regards,

Oliver

Oliver Graute (1):
imx: support for conga-QMX8 board

 arch/arm/dts/Makefile               |   1 +
 arch/arm/dts/imx8qm-cgtqmx8.dts     | 427 +++++++++++++++++++++++++
 arch/arm/mach-imx/Makefile          |   2 -
 arch/arm/mach-imx/imx8/Kconfig      |   7 +
 board/congatec/cgtqmx8/Kconfig      |  14 +
 board/congatec/cgtqmx8/MAINTAINERS  |   6 +
 board/congatec/cgtqmx8/Makefile     |  11 +
 board/congatec/cgtqmx8/README       |  15 +
 board/congatec/cgtqmx8/cgtqmx8.c    | 478 ++++++++++++++++++++++++++++
 board/congatec/cgtqmx8/imximage.cfg |  21 ++
 board/congatec/cgtqmx8/spl.c        |  75 +++++
 board/congatec/common/Kconfig       |  48 +++
 board/congatec/common/Makefile      |  23 ++
 board/congatec/common/mmc.c         |  50 +++
 configs/cgtqmx8_defconfig           |  79 +++++
 include/configs/cgtqmx8.h           | 167 ++++++++++
 16 files changed, 1422 insertions(+), 2 deletions(-)
 create mode 100644 arch/arm/dts/imx8qm-cgtqmx8.dts
 create mode 100644 board/congatec/cgtqmx8/Kconfig
 create mode 100644 board/congatec/cgtqmx8/MAINTAINERS
 create mode 100644 board/congatec/cgtqmx8/Makefile
 create mode 100644 board/congatec/cgtqmx8/README
 create mode 100644 board/congatec/cgtqmx8/cgtqmx8.c
 create mode 100644 board/congatec/cgtqmx8/imximage.cfg
 create mode 100644 board/congatec/cgtqmx8/spl.c
 create mode 100644 board/congatec/common/Kconfig
 create mode 100644 board/congatec/common/Makefile
 create mode 100644 board/congatec/common/mmc.c
 create mode 100644 configs/cgtqmx8_defconfig
 create mode 100644 include/configs/cgtqmx8.h
Signature · 1 line
2.17.1
#1 lore raw

PATCH 1/1 imx: support for conga-QMX8 board

Add i.MX8QM qmx8 congatec board support

Boot log as below:
U-Boot 2019.10-00002-gfe063598db (Oct 10 2019 - 10:29:07 +0200)

CPU: NXP i.MX8QM RevB A53 at 1200 MHz

Model: congatec QMX8
Board: conga-QMX8
Build: SCFW 65afe5f6
Boot:  SD2
DRAM:  6 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2

Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial at 5a060000
Out:   serial at 5a060000
Err:   serial at 5a060000

switch to partitions #0, OK
mmc2 is current device
Net:
Error: ethernet at 5b040000 address not set.
eth-1: ethernet at 5b040000
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc2 is current device

Cc Stefano Babic <[email protected]>
Cc Fabio Estevam <[email protected]>
Cc Peng Fan <[email protected]>
Cc Simon Glass <[email protected]>
Cc uboot-imx <[email protected]>
---
 arch/arm/dts/Makefile               |   1 +
 arch/arm/dts/imx8qm-cgtqmx8.dts     | 427 +++++++++++++++++++++++++
 arch/arm/mach-imx/Makefile          |   2 -
 arch/arm/mach-imx/imx8/Kconfig      |   7 +
 board/congatec/cgtqmx8/Kconfig      |  14 +
 board/congatec/cgtqmx8/MAINTAINERS  |   6 +
 board/congatec/cgtqmx8/Makefile     |  11 +
 board/congatec/cgtqmx8/README       |  15 +
 board/congatec/cgtqmx8/cgtqmx8.c    | 478 ++++++++++++++++++++++++++++
 board/congatec/cgtqmx8/imximage.cfg |  21 ++
 board/congatec/cgtqmx8/spl.c        |  75 +++++
 board/congatec/common/Kconfig       |  48 +++
 board/congatec/common/Makefile      |  23 ++
 board/congatec/common/mmc.c         |  50 +++
 configs/cgtqmx8_defconfig           |  79 +++++
 include/configs/cgtqmx8.h           | 167 ++++++++++
 16 files changed, 1422 insertions(+), 2 deletions(-)
 create mode 100644 arch/arm/dts/imx8qm-cgtqmx8.dts
 create mode 100644 board/congatec/cgtqmx8/Kconfig
 create mode 100644 board/congatec/cgtqmx8/MAINTAINERS
 create mode 100644 board/congatec/cgtqmx8/Makefile
 create mode 100644 board/congatec/cgtqmx8/README
 create mode 100644 board/congatec/cgtqmx8/cgtqmx8.c
 create mode 100644 board/congatec/cgtqmx8/imximage.cfg
 create mode 100644 board/congatec/cgtqmx8/spl.c
 create mode 100644 board/congatec/common/Kconfig
 create mode 100644 board/congatec/common/Makefile
 create mode 100644 board/congatec/common/mmc.c
 create mode 100644 configs/cgtqmx8_defconfig
 create mode 100644 include/configs/cgtqmx8.h
arch/arm/dts/Makefile +1 -0
index 2c86b293a8..9541ee614f 100644
@@ -638,6 +638,7 @@ dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-evk.dtb
 dtb-$(CONFIG_ARCH_IMX8) += \
 	fsl-imx8qm-apalis.dtb \
 	fsl-imx8qm-mek.dtb \
+	imx8qm-cgtqmx8.dtb \
 	fsl-imx8qxp-colibri.dtb \
 	fsl-imx8qxp-mek.dtb
 
arch/arm/dts/imx8qm-cgtqmx8.dts new file +427 -0

427 lines not on this page · raw message

arch/arm/mach-imx/Makefile +0 -2
index fbd99a3499..891631055a 100644
@@ -152,10 +152,8 @@ ifeq ($(DEPFILE_EXISTS),0)
 endif
 
 flash.bin: spl/u-boot-spl-ddr.bin u-boot.itb FORCE
-ifeq ($(DEPFILE_EXISTS),0)
 	$(call if_changed,mkimage)
 endif
-endif
 
 ifeq ($(CONFIG_ARCH_IMX8), y)
 SPL:
arch/arm/mach-imx/imx8/Kconfig +7 -0
index d17760e333..d47946d744 100644
@@ -55,6 +55,12 @@ config TARGET_IMX8QM_MEK
 	select BOARD_LATE_INIT
 	select IMX8QM
 
+config TARGET_CONGA_QMX8
+	bool "Support congatec conga-QMX8 board"
+	select BOARD_LATE_INIT
+	select SUPPORT_SPL
+	select IMX8QM
+
 config TARGET_IMX8QXP_MEK
 	bool "Support i.MX8QXP MEK board"
 	select BOARD_LATE_INIT
@@ -64,6 +70,7 @@ endchoice
 
 source "board/freescale/imx8qm_mek/Kconfig"
 source "board/freescale/imx8qxp_mek/Kconfig"
+source "board/congatec/cgtqmx8/Kconfig"
 source "board/toradex/apalis-imx8/Kconfig"
 source "board/toradex/colibri-imx8x/Kconfig"
 
board/congatec/cgtqmx8/Kconfig new file +14 -0
new file mode 100644
index 0000000000..7273039261
@@ -0,0 +1,14 @@
+if TARGET_CONGA_QMX8
+
+config SYS_BOARD
+	default "cgtqmx8"
+
+config SYS_VENDOR
+	default "congatec"
+
+config SYS_CONFIG_NAME
+	default "cgtqmx8"
+
+source "board/congatec/common/Kconfig"
+
+endif
board/congatec/cgtqmx8/MAINTAINERS new file +6 -0
new file mode 100644
index 0000000000..a242e534c8
@@ -0,0 +1,6 @@
+i.MX8QM CGTQMX8 BOARD
+M:	Oliver Graute <[email protected]>
+S:	Maintained
+F:	board/congatec/cgtqmx8/
+F:	include/configs/cgtqmx8.h
+F:	configs/cgtqmx8_defconfig
board/congatec/cgtqmx8/Makefile new file +11 -0
new file mode 100644
index 0000000000..4b59dbb6bc
@@ -0,0 +1,11 @@
+#
+# Copyright 2017 NXP
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y += cgtqmx8.o
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+endif
board/congatec/cgtqmx8/README new file +15 -0
new file mode 100644
index 0000000000..5724eb89f7
@@ -0,0 +1,15 @@
+Build U-Boot
+============
+
+$ export ATF_LOAD_ADDR=0x80000000
+$ export BL33_LOAD_ADDR=0x80020000
+$ make cgtqmx8_defconfig
+$ make u-boot.bin
+$ make flash.bin
+
+Flash the binary into the SD card
+=================================
+
+Burn the flash.bin binary to SD card offset 32KB:
+
+$ sudo dd if=flash.bin of=/dev/sd[x] bs=1k seek=32 conv=fsync
board/congatec/cgtqmx8/cgtqmx8.c new file +478 -0

478 lines not on this page · raw message

board/congatec/cgtqmx8/imximage.cfg new file +21 -0
new file mode 100644
index 0000000000..e324c7ca37
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier:	GPL-2.0+ */
+/*
+ * Copyright 2018 NXP
+ */
+
+#define __ASSEMBLY__
+
+/* Boot from SD, sector size 0x400 */
+BOOT_FROM SD 0x400
+/* SoC type IMX8QM */
+SOC_TYPE IMX8QM
+/* Append seco container image */
+APPEND mx8qm-ahab-container.img
+/* Create the 2nd container */
+CONTAINER
+/* Add scfw image with exec attribute */
+IMAGE SCU mx8qm-val-scfw-tcm.bin
+/* Add ATF image with exec attribute */
+IMAGE A35 bl31.bin 0x80000000
+/* Add U-Boot image with load attribute */
+DATA A35 u-boot-dtb.bin 0x80020000
board/congatec/cgtqmx8/spl.c new file +75 -0

75 lines not on this page · raw message

board/congatec/common/Kconfig new file +48 -0

48 lines not on this page · raw message

board/congatec/common/Makefile new file +23 -0
new file mode 100644
index 0000000000..d4ddfbf971
@@ -0,0 +1,23 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+MINIMAL=
+
+ifdef CONFIG_SPL_BUILD
+ifdef CONFIG_SPL_INIT_MINIMAL
+MINIMAL=y
+endif
+endif
+
+ifdef MINIMAL
+# necessary to create built-in.o
+obj- := __dummy__.o
+else
+
+obj-y				+= mmc.o
+
+endif
board/congatec/common/mmc.c new file +50 -0

50 lines not on this page · raw message

configs/cgtqmx8_defconfig new file +79 -0

79 lines not on this page · raw message

include/configs/cgtqmx8.h new file +167 -0

167 lines not on this page · raw message

Signature · 1 line
2.17.1