Skip to contentSkip to conversation

arm: mxs: Increase VDDD voltage to match specification

PATCH New Marek Vasut 3 participants 3 messages Oct 15, 2019 – Nov 4, 2019

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 arm: mxs: Increase VDDD voltage to match specification

According to IMX28CEC rev. 4, 10/2018, Table 15. Recommended Operating Conditions, page 16, the VDDD should be set to 1.55V when the CPU is operating at 454MHz. This is the case in U-Boot, hence increase the VDDD voltage. This fixes instability when performing TFTP transfers. Increase the brownout threshold to 1.4V. The documentation recommends 1.45V setting for the brownout, however, this triggers failure during power block init, so keep the brownout slightly lower.

---
 arch/arm/cpu/arm926ejs/mxs/spl_power_init.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm/cpu/arm926ejs/mxs/spl_power_init.c +2 -2
index a5c528a18d..7a1b39844e 100644
@@ -1254,8 +1254,8 @@ void mxs_power_init(void)
 	debug("SPL: Setting VDDIO to 3V3 (brownout @ 3v15)\n");
 	mxs_power_set_vddx(&mxs_vddio_cfg, 3300, 3150);
 
-	debug("SPL: Setting VDDD to 1V5 (brownout @ 1v315)\n");
-	mxs_power_set_vddx(&mxs_vddd_cfg, 1500, 1315);
+	debug("SPL: Setting VDDD to 1V55 (brownout @ 1v400)\n");
+	mxs_power_set_vddx(&mxs_vddd_cfg, 1550, 1400);
 #ifdef CONFIG_MX23
 	debug("SPL: Setting mx23 VDDMEM to 2V5 (brownout @ 1v7)\n");
 	mxs_power_set_vddx(&mxs_vddmem_cfg, 2500, 1700);
Signature · 1 line
2.23.0
reviewer
#1 lore raw

PATCH 1/1 arm: mxs: Increase VDDD voltage to match specification

Hi Marek,

Quoted 11 lines · Marek Vasut

According to IMX28CEC rev. 4, 10/2018, Table 15. Recommended Operating Conditions, page 16, the VDDD should be set to 1.55V when the CPU is operating at 454MHz. This is the case in U-Boot, hence increase the VDDD voltage. This fixes instability when performing TFTP transfers. Increase the brownout threshold to 1.4V. The documentation recommends 1.45V setting for the brownout, however, this triggers failure during power block init, so keep the brownout slightly lower.

Looks good, thanks:

#2 lore raw

PATCH 1/1 arm: mxs: Increase VDDD voltage to match specification

In reply to Marek Vasut
Quoted 10 lines

According to IMX28CEC rev. 4, 10/2018, Table 15. Recommended Operating Conditions, page 16, the VDDD should be set to 1.55V when the CPU is operating at 454MHz. This is the case in U-Boot, hence increase the VDDD voltage. This fixes instability when performing TFTP transfers. Increase the brownout threshold to 1.4V. The documentation recommends 1.45V setting for the brownout, however, this triggers failure during power block init, so keep the brownout slightly lower.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================