Skip to contentSkip to conversation

NVIDIA Tegra20 CPUFreq driver major update

PATCH Superseded Dmitry Osipenko 1 participant 11 messages Nov 11, 2019

Subsystems (7)
Device tree bindings Arm (32-bit) Arm sub-architectures Common clk +3 more subsystems

v4 of 8 Superseded Latest is v8 →

lore
Share & tools
lore

Dmitry Osipenko

author
#0 lore raw

v4 cover NVIDIA Tegra20 CPUFreq driver major update

Hello,

This series moves intermediate-clk handling from tegra20-cpufreq into tegra-clk driver. This allows us to switch to generic cpufreq-dt driver which brings voltage scaling, per-hardware OPPs and Tegra30 support out of the box. All boards need to adopt CPU OPPs in their device-trees in order to get cpufreq support.

Changelog:

v4: - Updated CCLK diagram in the "Add custom CCLK implementation" patch.

- <linux/cpu.h> is now included in the "Use generic cpufreq-dt driver" patch, for consistency.

- Returned value of get_cpu_device() is now checked in the "Use generic cpufreq-dt driver" patch, for consistency as well.

v3: - The "Add custom CCLK implementation" patch was updated in accordance
to the comments from Peter De Schrijver. We will not use the clock skipper.

- Re added OPPs for T30 Beaver board because Thierry has that board ;)

- Added r-b for the "DT binding" patch from Rob Herring.

v2: - Kept modularity of the tegra20-cpufreq as was requested by Viresh Kumar
in a review comment to v1.

- Added acks from Viresh Kumar.

- Added tested-by from Nicolas Chauvet to the "trimslice" patch. Nicolas told me on IRC that it works fine.

- Fixed compilation of the "Add custom CCLK implementation" patch. The error happened because v1 was based on top of yet unreviewed/unapplied patch "clk: tegra: divider: Support enable-bit for Super clocks". Thanks to Peter Geis for reporting the problem.

- Replaced Tegra30 "beaver" board with "cardhu-a04" because turned out that's what NVIDIA uses in the testing farm.

Dmitry Osipenko (10):
clk: tegra: Add custom CCLK implementation
clk: tegra: pll: Add pre/post rate-change hooks
clk: tegra: cclk: Add helpers for handling PLLX rate changes
clk: tegra20: Use custom CCLK implementation
clk: tegra30: Use custom CCLK implementation
dt-bindings: cpufreq: Add binding for NVIDIA Tegra20/30
cpufreq: tegra20: Use generic cpufreq-dt driver (Tegra30 supported
now)
ARM: tegra: Create tegra20-cpufreq platform device on Tegra30
ARM: dts: tegra30: beaver: Set up voltage regulators for DVFS
ARM: dts: tegra30: beaver: Add CPU Operating Performance Points

 .../cpufreq/nvidia,tegra20-cpufreq.txt        |  56 +++++
 arch/arm/boot/dts/tegra30-beaver.dts          |  40 +++-
 arch/arm/mach-tegra/tegra.c                   |   4 +
 drivers/clk/tegra/Makefile                    |   1 +
 drivers/clk/tegra/clk-pll.c                   |  12 +-
 drivers/clk/tegra/clk-tegra-super-cclk.c      | 212 +++++++++++++++++
 drivers/clk/tegra/clk-tegra20.c               |   7 +-
 drivers/clk/tegra/clk-tegra30.c               |   6 +-
 drivers/clk/tegra/clk.h                       |  19 +-
 drivers/cpufreq/Kconfig.arm                   |   6 +-
 drivers/cpufreq/cpufreq-dt-platdev.c          |   2 +
 drivers/cpufreq/tegra20-cpufreq.c             | 217 +++++-------------
 12 files changed, 408 insertions(+), 174 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/cpufreq/nvidia,tegra20-cpufreq.txt
 create mode 100644 drivers/clk/tegra/clk-tegra-super-cclk.c
Signature · 1 line
2.23.0
author
#1 lore raw

PATCH v4 1/10 clk: tegra: Add custom CCLK implementation

CCLK stands for "CPU Clock", CPU core is running off CCLK. CCLK supports multiple parents, it has internal clock divider and a clock skipper. PLLX is the main CCLK parent that provides clock rates above 1GHz and it has special property such that the CCLK's internal divider is set into bypass mode when PLLX is selected as a parent for CCLK.

This patch forks generic Super Clock into CCLK implementation which takes into account all CCLK specifics. The proper CCLK implementation is needed by the upcoming Tegra20 CPUFreq driver update that will allow to utilize the generic cpufreq-dt driver by moving intermediate clock selection into the clock driver.

Note that technically this patch could be squashed into clk-super.c, but it is cleaner to have a separate source file. Also note that currently all CCLKLP bits are left in the clk-super.c and only CCLKG is supported by clk-tegra-super-cclk. It shouldn't be difficult to move the CCLKLP bits, but CCLKLP is not used by anything in kernel and thus better not to touch it for now.

Signed-off-by Dmitry Osipenko <[email protected]>
---
 drivers/clk/tegra/Makefile               |   1 +
 drivers/clk/tegra/clk-tegra-super-cclk.c | 178 +++++++++++++++++++++++
 drivers/clk/tegra/clk.h                  |  11 +-
 3 files changed, 188 insertions(+), 2 deletions(-)
 create mode 100644 drivers/clk/tegra/clk-tegra-super-cclk.c
drivers/clk/tegra/Makefile +1 -0
index df966ca06788..f04b490f5416 100644
@@ -14,6 +14,7 @@ obj-y					+= clk-tegra-audio.o
 obj-y					+= clk-tegra-periph.o
 obj-y					+= clk-tegra-pmc.o
 obj-y					+= clk-tegra-fixed.o
+obj-y					+= clk-tegra-super-cclk.o
 obj-y					+= clk-tegra-super-gen4.o
 obj-$(CONFIG_TEGRA_CLK_EMC)		+= clk-emc.o
 obj-$(CONFIG_ARCH_TEGRA_2x_SOC)         += clk-tegra20.o
drivers/clk/tegra/clk-tegra-super-cclk.c new file +178 -0

178 lines not on this page · raw message

drivers/clk/tegra/clk.h +9 -2
index 416a6b09f6a3..ee35a847df08 100644
@@ -729,8 +729,10 @@ struct clk *tegra_clk_register_periph_data(void __iomem *clk_base,
  * TEGRA_DIVIDER_2 - LP cluster has additional divider. This flag indicates
  *     that this is LP cluster clock.
  * TEGRA210_CPU_CLK - This flag is used to identify CPU cluster for gen5
- * super mux parent using PLLP branches. To use PLLP branches to CPU, need
- * to configure additional bit PLLP_OUT_CPU in the clock registers.
+ *     super mux parent using PLLP branches. To use PLLP branches to CPU, need
+ *     to configure additional bit PLLP_OUT_CPU in the clock registers.
+ * TEGRA20_SUPER_CLK - Tegra20 doesn't have a dedicated divider for Super
+ *     clocks, it only has a clock-skipper.
  */
 struct tegra_clk_super_mux {
 	struct clk_hw	hw;

@@ -748,6 +750,7 @@ struct tegra_clk_super_mux {
 
 #define TEGRA_DIVIDER_2 BIT(0)
 #define TEGRA210_CPU_CLK BIT(1)
+#define TEGRA20_SUPER_CLK BIT(2)
 
 extern const struct clk_ops tegra_clk_super_ops;
 struct clk *tegra_clk_register_super_mux(const char *name,

@@ -758,6 +761,10 @@ struct clk *tegra_clk_register_super_clk(const char *name,
 		const char * const *parent_names, u8 num_parents,
 		unsigned long flags, void __iomem *reg, u8 clk_super_flags,
 		spinlock_t *lock);
+struct clk *tegra_clk_register_super_cclk(const char *name,
+		const char * const *parent_names, u8 num_parents,
+		unsigned long flags, void __iomem *reg, u8 clk_super_flags,
+		spinlock_t *lock);
 
 /**
  * struct tegra_sdmmc_mux - switch divider with Low Jitter inputs for SDMMC
Signature · 1 line
2.23.0
author
#2 lore raw

PATCH v4 2/10 clk: tegra: pll: Add pre/post rate-change hooks

In reply to Dmitry Osipenko

There is a need to temporarily re-parent CCLK away from PLLX if PLLX's rate is about to change. The newly introduced PLL pre/post rate-change hooks allow to handle such case.

Signed-off-by Dmitry Osipenko <[email protected]>
---
 drivers/clk/tegra/clk-pll.c | 12 +++++++++++-
 drivers/clk/tegra/clk.h     |  6 ++++++
 2 files changed, 17 insertions(+), 1 deletion(-)
drivers/clk/tegra/clk-pll.c +11 -1
index 531c2b3d814e..0b212cf2e794 100644
@@ -744,13 +744,19 @@ static int _program_pll(struct clk_hw *hw, struct tegra_clk_pll_freq_table *cfg,
 
 	state = clk_pll_is_enabled(hw);
 
+	if (state && pll->params->pre_rate_change) {
+		ret = pll->params->pre_rate_change();
+		if (WARN_ON(ret))
+			return ret;
+	}
+
 	_get_pll_mnp(pll, &old_cfg);
 
 	if (state && pll->params->defaults_set && pll->params->dyn_ramp &&
 			(cfg->m == old_cfg.m) && (cfg->p == old_cfg.p)) {
 		ret = pll->params->dyn_ramp(pll, cfg);
 		if (!ret)
-			return 0;
+			goto done;
 	}
 
 	if (state) {

@@ -772,6 +778,10 @@ static int _program_pll(struct clk_hw *hw, struct tegra_clk_pll_freq_table *cfg,
 		pll_clk_start_ss(pll);
 	}
 
+done:
+	if (state && pll->params->post_rate_change)
+		pll->params->post_rate_change();
+
 	return ret;
 }
drivers/clk/tegra/clk.h +6 -0
index ee35a847df08..fa18bef914af 100644
@@ -266,6 +266,10 @@ struct tegra_clk_pll;
  *				disabled.
  * @dyn_ramp:			Callback which can be used to define a custom
  *				dynamic ramp function for a given PLL.
+ * @pre_rate_change:		Callback which is invoked just before changing
+ *				PLL's rate.
+ * @post_rate_change:		Callback which is invoked right after changing
+ *				PLL's rate.
  *
  * Flags:
  * TEGRA_PLL_USE_LOCK - This flag indicated to use lock bits for

@@ -342,6 +346,8 @@ struct tegra_clk_pll_params {
 	void	(*set_defaults)(struct tegra_clk_pll *pll);
 	int	(*dyn_ramp)(struct tegra_clk_pll *pll,
 			struct tegra_clk_pll_freq_table *cfg);
+	int	(*pre_rate_change)(void);
+	void	(*post_rate_change)(void);
 };
 
 #define TEGRA_PLL_USE_LOCK BIT(0)
Signature · 1 line
2.23.0
author
#3 lore raw

PATCH v4 3/10 clk: tegra: cclk: Add helpers for handling PLLX rate changes

In reply to Dmitry Osipenko

CCLK should be re-parented away from PLLX if PLLX's rate is changing. The PLLP parent is a common safe CPU parent for all Tegra SoCs, thus CCLK will be re-parented to PLLP before PLLX rate-change begins and then switched back to PLLX after the rate-change completion. This patch adds helper functions which perform CCLK re-parenting, these helpers will be utilized by further patches.

Signed-off-by Dmitry Osipenko <[email protected]>
---
 drivers/clk/tegra/clk-tegra-super-cclk.c | 34 ++++++++++++++++++++++++
 drivers/clk/tegra/clk.h                  |  2 ++
 2 files changed, 36 insertions(+)
drivers/clk/tegra/clk-tegra-super-cclk.c +34 -0
index 7bcb9e8d0860..a03119c30456 100644
@@ -25,6 +25,9 @@
 
 #define SUPER_CDIV_ENB		BIT(31)
 
+static struct tegra_clk_super_mux *cclk_super;
+static bool cclk_on_pllx;
+
 static u8 cclk_super_get_parent(struct clk_hw *hw)
 {
 	return tegra_clk_super_ops.get_parent(hw);

@@ -115,6 +118,9 @@ struct clk *tegra_clk_register_super_cclk(const char *name,
 	struct clk_init_data init;
 	u32 val;
 
+	if (WARN_ON(cclk_super))
+		return ERR_PTR(-EBUSY);
+
 	super = kzalloc(sizeof(*super), GFP_KERNEL);
 	if (!super)
 		return ERR_PTR(-ENOMEM);

@@ -173,6 +179,34 @@ struct clk *tegra_clk_register_super_cclk(const char *name,
 	clk = clk_register(NULL, &super->hw);
 	if (IS_ERR(clk))
 		kfree(super);
+	else
+		cclk_super = super;
 
 	return clk;
 }
+
+int tegra_cclk_pre_pllx_rate_change(void)
+{
+	if (IS_ERR_OR_NULL(cclk_super))
+		return -EINVAL;
+
+	if (cclk_super_get_parent(&cclk_super->hw) == PLLX_INDEX)
+		cclk_on_pllx = true;
+	else
+		cclk_on_pllx = false;
+
+	/*
+	 * CPU needs to be temporarily re-parented away from PLLX if PLLX
+	 * changes its rate. PLLP is a safe parent for CPU on all Tegra SoCs.
+	 */
+	if (cclk_on_pllx)
+		cclk_super_set_parent(&cclk_super->hw, PLLP_INDEX);
+
+	return 0;
+}
+
+void tegra_cclk_post_pllx_rate_change(void)
+{
+	if (cclk_on_pllx)
+		cclk_super_set_parent(&cclk_super->hw, PLLX_INDEX);
+}
drivers/clk/tegra/clk.h +2 -0
index fa18bef914af..0afe28f4372b 100644
@@ -771,6 +771,8 @@ struct clk *tegra_clk_register_super_cclk(const char *name,
 		const char * const *parent_names, u8 num_parents,
 		unsigned long flags, void __iomem *reg, u8 clk_super_flags,
 		spinlock_t *lock);
+int tegra_cclk_pre_pllx_rate_change(void);
+void tegra_cclk_post_pllx_rate_change(void);
 
 /**
  * struct tegra_sdmmc_mux - switch divider with Low Jitter inputs for SDMMC
Signature · 1 line
2.23.0
author
#4 lore raw

PATCH v4 4/10 clk: tegra20: Use custom CCLK implementation

In reply to Dmitry Osipenko

We're going to use the generic cpufreq-dt driver on Tegra20 and thus CCLK intermediate re-parenting will be performed by the clock driver. There is now special CCLK implementation that supports all CCLK quirks, this patch makes Tegra20 SoCs to use that implementation.

Signed-off-by Dmitry Osipenko <[email protected]>
---
 drivers/clk/tegra/clk-tegra20.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/clk/tegra/clk-tegra20.c +5 -2
index 4d8222f5c638..eb821666ca61 100644
@@ -391,6 +391,8 @@ static struct tegra_clk_pll_params pll_x_params = {
 	.lock_delay = 300,
 	.freq_table = pll_x_freq_table,
 	.flags = TEGRA_PLL_HAS_CPCON | TEGRA_PLL_HAS_LOCK_ENABLE,
+	.pre_rate_change = tegra_cclk_pre_pllx_rate_change,
+	.post_rate_change = tegra_cclk_post_pllx_rate_change,
 };
 
 static struct tegra_clk_pll_params pll_e_params = {

@@ -704,9 +706,10 @@ static void tegra20_super_clk_init(void)
 	struct clk *clk;
 
 	/* CCLK */
-	clk = tegra_clk_register_super_mux("cclk", cclk_parents,
+	clk = tegra_clk_register_super_cclk("cclk", cclk_parents,
 			      ARRAY_SIZE(cclk_parents), CLK_SET_RATE_PARENT,
-			      clk_base + CCLK_BURST_POLICY, 0, 4, 0, 0, NULL);
+			      clk_base + CCLK_BURST_POLICY, TEGRA20_SUPER_CLK,
+			      NULL);
 	clks[TEGRA20_CLK_CCLK] = clk;
 
 	/* SCLK */
Signature · 1 line
2.23.0
author
#5 lore raw

PATCH v4 5/10 clk: tegra30: Use custom CCLK implementation

In reply to Dmitry Osipenko

We're going to use the generic cpufreq-dt driver on Tegra30 and thus CCLK intermediate re-parenting will be performed by the clock driver. There is now special CCLK implementation that supports all CCLK quirks, this patch makes Tegra30 SoCs to use that implementation.

Signed-off-by Dmitry Osipenko <[email protected]>
---
 drivers/clk/tegra/clk-tegra30.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/clk/tegra/clk-tegra30.c +4 -2
index c8bc18e4d7e5..0fe03d69fe1a 100644
@@ -499,6 +499,8 @@ static struct tegra_clk_pll_params pll_x_params __ro_after_init = {
 	.freq_table = pll_x_freq_table,
 	.flags = TEGRA_PLL_HAS_CPCON | TEGRA_PLL_SET_DCCON |
 		 TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE,
+	.pre_rate_change = tegra_cclk_pre_pllx_rate_change,
+	.post_rate_change = tegra_cclk_post_pllx_rate_change,
 };
 
 static struct tegra_clk_pll_params pll_e_params __ro_after_init = {

@@ -932,11 +934,11 @@ static void __init tegra30_super_clk_init(void)
 	clk_register_clkdev(clk, "pll_p_out4_cclkg", NULL);
 
 	/* CCLKG */
-	clk = tegra_clk_register_super_mux("cclk_g", cclk_g_parents,
+	clk = tegra_clk_register_super_cclk("cclk_g", cclk_g_parents,
 				  ARRAY_SIZE(cclk_g_parents),
 				  CLK_SET_RATE_PARENT,
 				  clk_base + CCLKG_BURST_POLICY,
-				  0, 4, 0, 0, NULL);
+				  0, NULL);
 	clks[TEGRA30_CLK_CCLK_G] = clk;
 
 	/*
Signature · 1 line
2.23.0
author
#6 lore raw

PATCH v4 6/10 dt-bindings: cpufreq: Add binding for NVIDIA Tegra20/30

In reply to Dmitry Osipenko

Add device-tree binding that describes CPU frequency-scaling hardware found on NVIDIA Tegra20/30 SoCs.

Acked-by Viresh Kumar <[email protected]>
Reviewed-by Rob Herring <[email protected]>
Signed-off-by Dmitry Osipenko <[email protected]>
---
 .../cpufreq/nvidia,tegra20-cpufreq.txt        | 56 +++++++++++++++++++
 1 file changed, 56 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/cpufreq/nvidia,tegra20-cpufreq.txt
Documentation/devicetree/bindings/cpufreq/nvidia,tegra20-cpufreq.txt new file +56 -0
new file mode 100644
index 000000000000..daeca6ae6b76
@@ -0,0 +1,56 @@
+Binding for NVIDIA Tegra20 CPUFreq
+==================================
+
+Required properties:
+- clocks: Must contain an entry for the CPU clock.
+  See ../clocks/clock-bindings.txt for details.
+- operating-points-v2: See ../bindings/opp/opp.txt for details.
+- #cooling-cells: Should be 2. See ../thermal/thermal.txt for details.
+
+For each opp entry in 'operating-points-v2' table:
+- opp-supported-hw: Two bitfields indicating:
+	On Tegra20:
+	1. CPU process ID mask
+	2. SoC speedo ID mask
+
+	On Tegra30:
+	1. CPU process ID mask
+	2. CPU speedo ID mask
+
+	A bitwise AND is performed against these values and if any bit
+	matches, the OPP gets enabled.
+
+- opp-microvolt: CPU voltage triplet.
+
+Optional properties:
+- cpu-supply: Phandle to the CPU power supply.
+
+Example:
+	regulators {
+		cpu_reg: regulator0 {
+			regulator-name = "vdd_cpu";
+		};
+	};
+
+	cpu0_opp_table: opp_table0 {
+		compatible = "operating-points-v2";
+
+		opp@456000000 {
+			clock-latency-ns = <125000>;
+			opp-microvolt = <825000 825000 1125000>;
+			opp-supported-hw = <0x03 0x0001>;
+			opp-hz = /bits/ 64 <456000000>;
+		};
+
+		...
+	};
+
+	cpus {
+		cpu@0 {
+			compatible = "arm,cortex-a9";
+			clocks = <&tegra_car TEGRA20_CLK_CCLK>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			cpu-supply = <&cpu_reg>;
+			#cooling-cells = <2>;
+		};
+	};
Signature · 1 line
2.23.0
author
#7 lore raw

PATCH v4 7/10 cpufreq: tegra20: Use generic cpufreq-dt driver (Tegra30 supported now)

In reply to Dmitry Osipenko

Re-parenting to intermediate clock is supported now by the clock driver and thus there is no need in a customized CPUFreq driver, all that code is common for both Tegra20 and Tegra30. The available CPU freqs are now specified in device-tree in a form of OPPs, all users should update their device-trees.

Acked-by Viresh Kumar <[email protected]>
Signed-off-by Dmitry Osipenko <[email protected]>
---
 drivers/cpufreq/Kconfig.arm          |   6 +-
 drivers/cpufreq/cpufreq-dt-platdev.c |   2 +
 drivers/cpufreq/tegra20-cpufreq.c    | 217 +++++++--------------------
 3 files changed, 61 insertions(+), 164 deletions(-)
drivers/cpufreq/Kconfig.arm +3 -3
index 3858d86cf409..92a6a5089979 100644
@@ -295,11 +295,11 @@ config ARM_TANGO_CPUFREQ
 	default y
 
 config ARM_TEGRA20_CPUFREQ
-	tristate "Tegra20 CPUFreq support"
-	depends on ARCH_TEGRA
+	tristate "Tegra20/30 CPUFreq support"
+	depends on ARCH_TEGRA && CPUFREQ_DT
 	default y
 	help
-	  This adds the CPUFreq driver support for Tegra20 SOCs.
+	  This adds the CPUFreq driver support for Tegra20/30 SOCs.
 
 config ARM_TEGRA124_CPUFREQ
 	bool "Tegra124 CPUFreq support"
drivers/cpufreq/cpufreq-dt-platdev.c +2 -0
index f1d170dcf4d3..aba591d57c67 100644
@@ -121,6 +121,8 @@ static const struct of_device_id blacklist[] __initconst = {
 	{ .compatible = "mediatek,mt8176", },
 	{ .compatible = "mediatek,mt8183", },
 
+	{ .compatible = "nvidia,tegra20", },
+	{ .compatible = "nvidia,tegra30", },
 	{ .compatible = "nvidia,tegra124", },
 	{ .compatible = "nvidia,tegra210", },
drivers/cpufreq/tegra20-cpufreq.c +56 -161

257 lines not on this page · raw message

Signature · 1 line
2.23.0
author
#8 lore raw

PATCH v4 8/10 ARM: tegra: Create tegra20-cpufreq platform device on Tegra30

In reply to Dmitry Osipenko

The tegra20-cpufreq now instantiates cpufreq-dt and Tegra30 is fully supported by that driver.

Signed-off-by Dmitry Osipenko <[email protected]>
---
 arch/arm/mach-tegra/tegra.c | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm/mach-tegra/tegra.c +4 -0
index e512e606eabd..1e3b85923ca3 100644
@@ -95,6 +95,10 @@ static void __init tegra_dt_init_late(void)
 	if (IS_ENABLED(CONFIG_ARCH_TEGRA_2x_SOC) &&
 	    of_machine_is_compatible("nvidia,tegra20"))
 		platform_device_register_simple("tegra20-cpufreq", -1, NULL, 0);
+
+	if (IS_ENABLED(CONFIG_ARCH_TEGRA_3x_SOC) &&
+	    of_machine_is_compatible("nvidia,tegra30"))
+		platform_device_register_simple("tegra20-cpufreq", -1, NULL, 0);
 }
 
 static const char * const tegra_dt_board_compat[] = {
Signature · 1 line
2.23.0
author
#9 lore raw

PATCH v4 9/10 ARM: dts: tegra30: beaver: Set up voltage regulators for DVFS

In reply to Dmitry Osipenko

Set min/max voltage and couple CPU/CORE regulators.

Signed-off-by Dmitry Osipenko <[email protected]>
---
 arch/arm/boot/dts/tegra30-beaver.dts | 16 +++++++++++++---
 1 file changed, 13 insertions(+), 3 deletions(-)
arch/arm/boot/dts/tegra30-beaver.dts +13 -3
index a3b0f3555cd2..6ebb3105af9e 100644
@@ -1806,9 +1806,14 @@
 
 				vddctrl_reg: vddctrl {
 					regulator-name = "vdd_cpu,vdd_sys";
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1000000>;
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-coupled-with = <&core_vdd_reg>;
+					regulator-coupled-max-spread = <300000>;
+					regulator-max-step-microvolt = <100000>;
 					regulator-always-on;
+
+					nvidia,tegra-cpu-regulator;
 				};
 
 				vio_reg: vio {

@@ -1868,17 +1873,22 @@
 			};
 		};
 
-		tps62361@60 {
+		core_vdd_reg: tps62361@60 {
 			compatible = "ti,tps62361";
 			reg = <0x60>;
 
 			regulator-name = "tps62361-vout";
 			regulator-min-microvolt = <500000>;
 			regulator-max-microvolt = <1500000>;
+			regulator-coupled-with = <&vddctrl_reg>;
+			regulator-coupled-max-spread = <300000>;
+			regulator-max-step-microvolt = <100000>;
 			regulator-boot-on;
 			regulator-always-on;
 			ti,vsel0-state-high;
 			ti,vsel1-state-high;
+
+			nvidia,tegra-core-regulator;
 		};
 	};
Signature · 1 line
2.23.0
author
#10 lore raw

PATCH v4 10/10 ARM: dts: tegra30: beaver: Add CPU Operating Performance Points

In reply to Dmitry Osipenko

Utilize common Tegra30 CPU OPP table. CPU DVFS is available now on beaver.

Signed-off-by Dmitry Osipenko <[email protected]>
---
 arch/arm/boot/dts/tegra30-beaver.dts | 24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)
arch/arm/boot/dts/tegra30-beaver.dts +24 -0
index 6ebb3105af9e..86556622be25 100644
@@ -2,6 +2,8 @@
 /dts-v1/;
 
 #include "tegra30.dtsi"
+#include "tegra30-cpu-opp.dtsi"
+#include "tegra30-cpu-opp-microvolt.dtsi"
 
 / {
 	model = "NVIDIA Tegra30 Beaver evaluation board";

@@ -2124,4 +2126,26 @@
 			 <&tegra_car TEGRA30_CLK_EXTERN1>;
 		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
+
+	cpus {
+		cpu0: cpu@0 {
+			cpu-supply = <&vddctrl_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
+		cpu@1 {
+			cpu-supply = <&vddctrl_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
+		cpu@2 {
+			cpu-supply = <&vddctrl_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
+		cpu@3 {
+			cpu-supply = <&vddctrl_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+	};
 };
Signature · 1 line
2.23.0