Add suppport for rm69299 Visionox panel driver and add DSI config to support DSI version
Subsystems (5)
cover Add suppport for rm69299 Visionox panel driver and add DSI config to support DSI version
Current patchset adds support for rm69299 visionox panel driver used in MSM reference platforms and also adds DSI config that supports the respective DSI version.
The visionox panel driver supports a resolution of 1080x2248 with 4 lanes and supports only single DSI mode.
Current patchset is tested on actual panel.
Harigovindan P (2):
drm/panel: add support for rm69299 visionox panel driver drm/msm: add DSI config changes to support DSI version
drivers/gpu/drm/msm/dsi/dsi_cfg.c | 21 ++ drivers/gpu/drm/msm/dsi/dsi_cfg.h | 1 + drivers/gpu/drm/panel/Kconfig | 9 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-visionox-rm69299.c | 478 +++++++++++++++++++++++++ 5 files changed, 510 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-visionox-rm69299.c
Signature · 1 line
2.7.4
PATCH 1/2 drm/panel: add support for rm69299 visionox panel driver
Add support for Visionox panel driver.
--- drivers/gpu/drm/panel/Kconfig | 9 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-visionox-rm69299.c | 478 +++++++++++++++++++++++++ 3 files changed, 488 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-visionox-rm69299.c
drivers/gpu/drm/panel/Kconfig +9 -0
@@ -355,4 +355,13 @@ config DRM_PANEL_TRULY_NT35597_WQXGA help Say Y here if you want to enable support for Truly NT35597 WQXGA Dual DSI Video Mode panel + +config DRM_PANEL_VISIONOX_RM69299 + tristate "Visionox RM69299" + depends on OF + depends on DRM_MIPI_DSI + help + Say Y here if you want to enable support for Visionox + RM69299 DSI Video Mode panel. + endmenu
drivers/gpu/drm/panel/Makefile +1 -0
@@ -38,3 +38,4 @@ obj-$(CONFIG_DRM_PANEL_TPO_TD028TTEC1) += panel-tpo-td028ttec1.o obj-$(CONFIG_DRM_PANEL_TPO_TD043MTEA1) += panel-tpo-td043mtea1.o obj-$(CONFIG_DRM_PANEL_TPO_TPG110) += panel-tpo-tpg110.o obj-$(CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA) += panel-truly-nt35597.o +obj-$(CONFIG_DRM_PANEL_VISIONOX_RM69299) += panel-visionox-rm69299.o
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +478 -0
478 lines not on this page · raw message
Signature · 1 line
2.7.4
Re: [PATCH v1 1/2] drm/panel: add support for rm69299 visionox panel driver
Quoting Harigovindan P (2019-11-14 02:16:27)
Quoted 6 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +0
-0
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 9
Quoted 9 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +9
-0@@ -0,0 +1,478 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* Copyright (c) 2019, The Linux Foundation. All rights reserved. +*/ + +#include <drm/drm_panel.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_modes.h> +#include <drm/drm_panel.h>
This is included twice. It's really a panel!
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 12
Quoted 3 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +3
-0+#include <drm/drm_print.h> + +#include <linux/of_gpio.h>
Is this include used?
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 15
Quoted 3 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +3
-0+#include <linux/gpio/consumer.h> +#include <linux/of_device.h> +#include <linux/of_graph.h>
Is this include used?
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 16
Quoted 1 line
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +1
-0+#include <linux/pinctrl/consumer.h>
Is this include used?
Quoted 11 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +11
-0+#include <linux/regulator/consumer.h> +#include <linux/backlight.h> +#include <linux/module.h> +#include <linux/delay.h> + +#include <video/mipi_display.h> + +static const char *const regulator_names[] = { +"vdda" , +"vdd3p3" , +};
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 37
Quoted 10 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +10
-0+ +static unsigned long const regulator_enable_loads[] = { +32000 , +13200 , +}; + +static unsigned long const regulator_disable_loads[] = { +80 , +80 , +};
Why do we need these static arrays for two regulators? Is the panel going to have additional regulators added in the future? I'd prefer these arrays go away and the regulator setup is open coded in probe. Maybe that means dropping the use of bulk APIs, I'm not sure.
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 46
Quoted 9 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +9
-0+ +struct cmd_set { +u8 commands[4 ]; +u8 size; +}; + +struct rm69299_config { +u32 width_mm; +u32 height_mm;
Why u32 for these types? Do they need to be 32 bits wide or can they be more generic like unsigned long types?
Quoted 18 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +18
-0+const char *panel_name; +const struct cmd_set *panel_on_cmds; +u32 num_on_cmds; +const struct drm_display_mode *dm; +}; + +struct visionox_rm69299 { +struct device *dev; +struct drm_panel panel; + +struct regulator_bulk_data supplies[ARRAY_SIZE (regulator_names)]; + +struct gpio_desc *reset_gpio; + +struct backlight_device *backlight; + +struct mipi_dsi_device *dsi; +const struct rm69299_config *config;
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 74
Quoted 10 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +10
-0+bool prepared; +bool enabled; +}; + +static inline struct visionox_rm69299 *panel_to_ctx (struct drm_panel *panel) +{ + return container_of(panel, struct visionox_rm69299, panel); +} + +static const struct cmd_set qcom_rm69299_1080p_panel_magic_cmds[] = {
I like magic.
Quoted 17 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +17
-0+ { { 0xfe, 0x00 }, 2 }, + { { 0xc2, 0x08 }, 2 }, + { { 0x35, 0x00 }, 2 }, + { { 0x51, 0xff }, 2 }, +}; + +static int visionox_dcs_write(struct drm_panel *panel, u32 command) +{ + struct visionox_rm69299 *ctx = panel_to_ctx(panel); + int i = 0, ret; + + ret = mipi_dsi_dcs_write(ctx->dsi, command, NULL, 0); + if (ret < 0) { + DRM_DEV_ERROR(ctx->dev, + "cmd 0x%x failed for dsi = %d\n", + command, i); + }
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 101
Quoted 10 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +10
-0+ +return ret; +} + +static int visionox_dcs_write_buf (struct drm_panel *panel, +u32 size,const u8 *buf) +{ +struct visionox_rm69299 *ctx =panel_to_ctx (panel); +int ret =0 ; +int i =0 ;
Please don't assign variables by default and then reassign them without testing them in between. Also, i is never used so it's confusing that it isn't just hardcoded into the printk message as '0'.
Quoted 4 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +4
-0+ + ret =mipi_dsi_dcs_write_buffer (ctx->dsi, buf, size); +if (ret <0 ) { + DRM_DEV_ERROR(ctx->dev,
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 115
Quoted 10 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +10
-0+ "failed to tx cmd [%d], err: %d\n", i, ret); +return ret; + } + +return ret; +} + +static int visionox_35597_power_on (struct visionox_rm69299 *ctx) +{ +int ret, i;
Nitpick: Add a newline between declarations and statements.
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 125
Quoted 10 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +10
-0+for (i =0 ; i <ARRAY_SIZE (ctx->supplies); i++) { + ret =regulator_set_load (ctx->supplies[i].consumer, + regulator_enable_loads[i]); +if (ret) +return ret; + } + + ret =regulator_bulk_enable (ARRAY_SIZE (ctx->supplies), ctx->supplies); +if (ret <0 ) +return ret;
We forgot to drop the load... O well. Probably best to just never drop the load anyway, see below.
Quoted 9 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +9
-0+ +/* +* Reset sequence of visionox panel requires the panel to be +* out of reset for 10ms, followed by being held in reset +* for 10ms and then out again +*/ +gpiod_set_value (ctx->reset_gpio,1 ); +usleep_range (10000 ,20000 ); +gpiod_set_value (ctx->reset_gpio,0 );
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 144
Quoted 10 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +10
-0+usleep_range (10000 ,20000 ); +gpiod_set_value (ctx->reset_gpio,1 ); +usleep_range (10000 ,20000 ); + +return 0 ; +} + +static int visionox_rm69299_power_off (struct visionox_rm69299 *ctx) +{ +int ret =0 ;
Ugh. Please stop pre-assigning ret.
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 151
Quoted 7 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +7
-0+int i; + +gpiod_set_value (ctx->reset_gpio,0 ); + +for (i =0 ; i <ARRAY_SIZE (ctx->supplies); i++) { + ret =regulator_set_load (ctx->supplies[i].consumer, + regulator_disable_loads[i]);
Do we need to drop the load? I thought that disabling the regulator would make the regulator core stop considering the load from these consumers.
Quoted 14 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +14
-0+if (ret) { +DRM_DEV_ERROR (ctx->dev, +"regulator_set_load failed %d\n" , ret); +return ret; + } + } + + ret =regulator_bulk_disable (ARRAY_SIZE (ctx->supplies), ctx->supplies); +if (ret) { +DRM_DEV_ERROR (ctx->dev, +"regulator_bulk_disable failed %d\n" , ret); + } +return ret; +}
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 175
Quoted 10 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +10
-0+ +static int visionox_rm69299_disable (struct drm_panel *panel) +{ +struct visionox_rm69299 *ctx =panel_to_ctx (panel); +int ret; + +if (!ctx->enabled) +return 0 ; + +if (ctx->backlight) {
backlight_disable() and backlight_enable() already check for NULL so these NULL checks can go away.
Quoted 15 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +15
-0+ ret =backlight_disable (ctx->backlight); +if (ret <0 ) +DRM_DEV_ERROR (ctx->dev,"backlight disable failed %d\n" , + ret); + } + + ctx->enabled = false; +return 0 ; +} + +static int visionox_rm69299_unprepare (struct drm_panel *panel) +{ +struct visionox_rm69299 *ctx =panel_to_ctx (panel); +int ret =0 ; +
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 200
Quoted 10 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +10
-0+if (!ctx->prepared) +return 0 ; + + ctx->dsi->mode_flags =0 ; + + ret =visionox_dcs_write (panel,MIPI_DCS_SET_DISPLAY_OFF ); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev, +"set_display_off cmd failed ret = %d\n" , + ret);
There will be double error prints in this case. Can we just have one print instead?
Quoted 127 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +127
-0+ } + +/* 120ms delay required here as per DCS spec */ +msleep (120 ); + + ret =visionox_dcs_write (panel,MIPI_DCS_ENTER_SLEEP_MODE ); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev, +"enter_sleep cmd failed ret = %d\n" , ret); + } + + ret =visionox_rm69299_power_off (ctx); +if (ret <0 ) +DRM_DEV_ERROR (ctx->dev,"power_off failed ret = %d\n" , ret); + + ctx->prepared = false; +return ret; +} + +static int visionox_rm69299_prepare (struct drm_panel *panel) +{ +struct visionox_rm69299 *ctx =panel_to_ctx (panel); +int ret; +int i; +const struct cmd_set *panel_on_cmds; +const struct rm69299_config *config; +u32 num_cmds; + +if (ctx->prepared) +return 0 ; + + ret =visionox_35597_power_on (ctx); +if (ret <0 ) +return ret; + + ctx->dsi->mode_flags |=MIPI_DSI_MODE_LPM ; + + config = ctx->config; + panel_on_cmds = config->panel_on_cmds; + num_cmds = config->num_on_cmds; + +for (i =0 ; i < num_cmds; i++) { + ret =visionox_dcs_write_buf (panel, + panel_on_cmds[i].size, + panel_on_cmds[i].commands); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev, +"cmd set tx failed i = %d ret = %d\n" , + i, ret); + goto power_off; + } + } + + ret =visionox_dcs_write (panel,MIPI_DCS_EXIT_SLEEP_MODE ); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev, +"exit_sleep_mode cmd failed ret = %d\n" , + ret); + goto power_off; + } + +/* Per DSI spec wait 120ms after sending exit sleep DCS command */ +msleep (120 ); + + ret =visionox_dcs_write (panel,MIPI_DCS_SET_DISPLAY_ON ); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev, +"set_display_on cmd failed ret = %d\n" , ret); + goto power_off; + } + +/* Per DSI spec wait 120ms after sending set_display_on DCS command */ +msleep (120 ); + + ctx->prepared = true; + +return 0 ; + +power_off: +if (visionox_rm69299_power_off (ctx)) +DRM_DEV_ERROR (ctx->dev,"power_off failed\n" ); +return ret; +} + +static int visionox_rm69299_enable (struct drm_panel *panel) +{ +struct visionox_rm69299 *ctx =panel_to_ctx (panel); +int ret; + +if (ctx->enabled) +return 0 ; + +if (ctx->backlight) { + ret =backlight_enable (ctx->backlight); +if (ret <0 ) +DRM_DEV_ERROR (ctx->dev,"backlight enable failed %d\n" , + ret); + } + + ctx->enabled = true; + +return 0 ; +} + +static int visionox_rm69299_get_modes (struct drm_panel *panel) +{ +struct drm_connector *connector = panel->connector; +struct visionox_rm69299 *ctx =panel_to_ctx (panel); +struct drm_display_mode *mode; +const struct rm69299_config *config; + + config = ctx->config; + mode =drm_mode_create (connector->dev); +if (!mode) { +DRM_DEV_ERROR (ctx->dev, +"failed to create a new display mode\n" ); +return 0 ; + } + + connector->display_info.width_mm = config->width_mm; + connector->display_info.height_mm = config->height_mm; +drm_mode_copy (mode, config->dm); + mode->type =DRM_MODE_TYPE_DRIVER |DRM_MODE_TYPE_PREFERRED ; +drm_mode_probed_add (connector, mode); + +return 1 ; +}
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 337
Quoted 10 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +10
-0+ +static const struct drm_panel_funcs visionox_rm69299_drm_funcs = { + .disable = visionox_rm69299_disable, + .unprepare = visionox_rm69299_unprepare, + .prepare = visionox_rm69299_prepare, + .enable = visionox_rm69299_enable, + .get_modes = visionox_rm69299_get_modes, +}; + +static int visionox_rm69299_panel_add (struct visionox_rm69299 *ctx)
Please inline this function into probe. It's not helping much to be split out.
Quoted 12 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +12
-0+{ +struct device *dev = ctx->dev; +int ret, i; +const struct rm69299_config *config; + + config = ctx->config; +for (i =0 ; i <ARRAY_SIZE (ctx->supplies); i++) + ctx->supplies[i].supply = regulator_names[i]; + + ret =devm_regulator_bulk_get (dev,ARRAY_SIZE (ctx->supplies), + ctx->supplies); +if (ret <0 )
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 359
Quoted 10 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +10
-0+return ret; + + ctx->reset_gpio =devm_gpiod_get (dev,"reset" ,GPIOD_OUT_LOW ); +if (IS_ERR (ctx->reset_gpio)) { +DRM_DEV_ERROR (dev,"cannot get reset gpio %ld\n" , +PTR_ERR (ctx->reset_gpio)); +return PTR_ERR (ctx->reset_gpio); + } + + ret =gpiod_direction_output (ctx->reset_gpio,0 );
Didn't the devm_gpiod_get() call above make the gpio use output direction already? Why call this again?
Quoted 38 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +38
-0+if (ret <0 ) { +pr_err ("direction output failed \n" ); + } + +drm_panel_init (&ctx->panel); + ctx->panel.dev = dev; + ctx->panel.funcs = &visionox_rm69299_drm_funcs; +drm_panel_add (&ctx->panel); + +return 0 ; +} + +static const struct drm_display_mode qcom_sc7180_mtp_1080p_mode = { + .name ="1080x2248" , + .clock =158695 , + .hdisplay =1080 , + .hsync_start =1080 +26 , + .hsync_end =1080 +26 +2 , + .htotal =1080 +26 +2 +36 , + .vdisplay =2248 , + .vsync_start =2248 +56 , + .vsync_end =2248 +56 +4 , + .vtotal =2248 +56 +4 +4 , + .vrefresh =60 , + .flags =0 , +}; + +static const struct rm69299_config rm69299_dir = { + .width_mm =74 , + .height_mm =131 , + .panel_name ="qcom_sc7180_mtp_1080p_panel" , + .dm = &qcom_sc7180_mtp_1080p_mode, + .panel_on_cmds = qcom_rm69299_1080p_panel_magic_cmds, + .num_on_cmds =ARRAY_SIZE (qcom_rm69299_1080p_panel_magic_cmds), +}; + +static int visionox_rm69299_probe (struct mipi_dsi_device *dsi) +{
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 407
Quoted 10 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +10
-0+struct device *dev = &dsi->dev; +struct visionox_rm69299 *ctx; +int ret =0 ; + + ctx =devm_kzalloc (dev,sizeof (*ctx),GFP_KERNEL ); + +if (!ctx) +return -ENOMEM ; + + ctx->config =of_device_get_match_data (dev);
Call device_get_match_data() instead?
Quoted 6 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +6
-0+ +if (!ctx->config) { +dev_err (dev,"missing device configuration\n" ); +return -ENODEV ; + } +
Re: [PATCH v1 1/2] drm/panel: add support for rm69299 visionox panel driver
In reply to Harigovindan PQuoted 113 lines · Harigovindan P
Add support for Visionox panel driver.
Signed-off-by Harigovindan P <[email protected]>--- drivers/gpu/drm/panel/Kconfig | 9 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-visionox-rm69299.c | 478 +++++++++++++++++++++++++ 3 files changed, 488 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-visionox-rm69299.cdrivers/gpu/drm/panel/Kconfig +9
-0@@ -355,4 +355,13 @@ config DRM_PANEL_TRULY_NT35597_WQXGA help Say Y here if you want to enable support for Truly NT35597 WQXGA Dual DSI Video Mode panel + +config DRM_PANEL_VISIONOX_RM69299 + tristate "Visionox RM69299" + depends on OF + depends on DRM_MIPI_DSI + help + Say Y here if you want to enable support for Visionox + RM69299 DSI Video Mode panel. + endmenudrivers/gpu/drm/panel/Makefile +1
-0@@ -38,3 +38,4 @@ obj-$(CONFIG_DRM_PANEL_TPO_TD028TTEC1) += panel-tpo-td028ttec1.o obj-$(CONFIG_DRM_PANEL_TPO_TD043MTEA1) += panel-tpo-td043mtea1.o obj-$(CONFIG_DRM_PANEL_TPO_TPG110) += panel-tpo-tpg110.o obj-$(CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA) += panel-truly-nt35597.o +obj-$(CONFIG_DRM_PANEL_VISIONOX_RM69299) += panel-visionox-rm69299.odrivers/gpu/drm/panel/panel-visionox-rm69299.c new file +69
-0@@ -0,0 +1,478 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* Copyright (c) 2019, The Linux Foundation. All rights reserved. +*/ + +#include <drm/drm_panel.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_modes.h> +#include <drm/drm_panel.h> +#include <drm/drm_print.h> + +#include <linux/of_gpio.h> +#include <linux/gpio/consumer.h> +#include <linux/of_device.h> +#include <linux/of_graph.h> +#include <linux/pinctrl/consumer.h> +#include <linux/regulator/consumer.h> +#include <linux/backlight.h> +#include <linux/module.h> +#include <linux/delay.h> + +#include <video/mipi_display.h> + +static const char *const regulator_names[] = { +"vdda" , +"vdd3p3" , +}; + +static unsigned long const regulator_enable_loads[] = { +32000 , +13200 , +}; + +static unsigned long const regulator_disable_loads[] = { +80 , +80 , +}; + +struct cmd_set { +u8 commands[4 ]; +u8 size; +}; + +struct rm69299_config { +u32 width_mm; +u32 height_mm; +const char *panel_name; +const struct cmd_set *panel_on_cmds; +u32 num_on_cmds; +const struct drm_display_mode *dm; +}; + +struct visionox_rm69299 { +struct device *dev; +struct drm_panel panel; + +struct regulator_bulk_data supplies[ARRAY_SIZE (regulator_names)]; + +struct gpio_desc *reset_gpio; + +struct backlight_device *backlight; + +struct mipi_dsi_device *dsi; +const struct rm69299_config *config; +bool prepared; +bool enabled; +}; + +static inline struct visionox_rm69299 *panel_to_ctx (struct drm_panel *panel)
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 79
Quoted 10 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +10
-0+{ + return container_of(panel, struct visionox_rm69299, panel); +} + +static const struct cmd_set qcom_rm69299_1080p_panel_magic_cmds[] = { + { {0xfe ,0x00 },2 }, + { {0xc2 ,0x08 },2 }, + { {0x35 ,0x00 },2 }, + { {0x51 ,0xff },2 }, +};
I'm not really seeing the value of a table of cmds, vs just a sequence of mipi_dsi_dcs_write_buffer() calls.. it is only used in one place, so it just seems like a level of indirection that doesn't add value, compared to something like:
mipi_dsi_dsc_write_buffer(dsi, (u8[]){ 0xfe, 0x00 }, 2);(otoh, some of the other panel so maybe Thierry is less picky)
Quoted 22 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +22
-0+ +static int visionox_dcs_write (struct drm_panel *panel,u32 command) +{ +struct visionox_rm69299 *ctx =panel_to_ctx (panel); +int i =0 , ret; + + ret =mipi_dsi_dcs_write (ctx->dsi, command,NULL ,0 ); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev, +"cmd 0x%x failed for dsi = %d\n" , + command, i); + } + +return ret; +} + +static int visionox_dcs_write_buf (struct drm_panel *panel, +u32 size,const u8 *buf) +{ +struct visionox_rm69299 *ctx =panel_to_ctx (panel); +int ret =0 ; +int i =0 ;
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 111
Quoted 10 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +10
-0+ + ret =mipi_dsi_dcs_write_buffer (ctx->dsi, buf, size); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev, +"failed to tx cmd [%d], err: %d\n" , i, ret); +return ret; + } + +return ret; +}
drop these two and just use mipi_dsi_dcs_write(_buffer)() directly.. the only extra thing these seem to do is error reporting, which is already done at the call-sites of these.
Quoted 75 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +75
-0+ +static int visionox_35597_power_on (struct visionox_rm69299 *ctx) +{ +int ret, i; +for (i =0 ; i <ARRAY_SIZE (ctx->supplies); i++) { + ret =regulator_set_load (ctx->supplies[i].consumer, + regulator_enable_loads[i]); +if (ret) +return ret; + } + + ret =regulator_bulk_enable (ARRAY_SIZE (ctx->supplies), ctx->supplies); +if (ret <0 ) +return ret; + +/* +* Reset sequence of visionox panel requires the panel to be +* out of reset for 10ms, followed by being held in reset +* for 10ms and then out again +*/ +gpiod_set_value (ctx->reset_gpio,1 ); +usleep_range (10000 ,20000 ); +gpiod_set_value (ctx->reset_gpio,0 ); +usleep_range (10000 ,20000 ); +gpiod_set_value (ctx->reset_gpio,1 ); +usleep_range (10000 ,20000 ); + +return 0 ; +} + +static int visionox_rm69299_power_off (struct visionox_rm69299 *ctx) +{ +int ret =0 ; +int i; + +gpiod_set_value (ctx->reset_gpio,0 ); + +for (i =0 ; i <ARRAY_SIZE (ctx->supplies); i++) { + ret =regulator_set_load (ctx->supplies[i].consumer, + regulator_disable_loads[i]); +if (ret) { +DRM_DEV_ERROR (ctx->dev, +"regulator_set_load failed %d\n" , ret); +return ret; + } + } + + ret =regulator_bulk_disable (ARRAY_SIZE (ctx->supplies), ctx->supplies); +if (ret) { +DRM_DEV_ERROR (ctx->dev, +"regulator_bulk_disable failed %d\n" , ret); + } +return ret; +} + +static int visionox_rm69299_disable (struct drm_panel *panel) +{ +struct visionox_rm69299 *ctx =panel_to_ctx (panel); +int ret; + +if (!ctx->enabled) +return 0 ; + +if (ctx->backlight) { + ret =backlight_disable (ctx->backlight); +if (ret <0 ) +DRM_DEV_ERROR (ctx->dev,"backlight disable failed %d\n" , + ret); + } + + ctx->enabled = false; +return 0 ; +} + +static int visionox_rm69299_unprepare (struct drm_panel *panel)
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 196
Quoted 10 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +10
-0+{ +struct visionox_rm69299 *ctx =panel_to_ctx (panel); +int ret =0 ; + +if (!ctx->prepared) +return 0 ; + + ctx->dsi->mode_flags =0 ; + + ret =visionox_dcs_write (panel,MIPI_DCS_SET_DISPLAY_OFF );
mipi_dsi_dcs_set_display_off()
drivers/gpu/drm/panel/panel-visionox-rm69299.c line 206
Quoted 10 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +10
-0+if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev, +"set_display_off cmd failed ret = %d\n" , + ret); + } + +/* 120ms delay required here as per DCS spec */ +msleep (120 ); + + ret =visionox_dcs_write (panel,MIPI_DCS_ENTER_SLEEP_MODE );
mipi_dsi_dcs_enter_sleep_mode()
(same comment at a few points below as well)
BR,
-R
Quoted 273 lines
drivers/gpu/drm/panel/panel-visionox-rm69299.c new file +272
-1+if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev, +"enter_sleep cmd failed ret = %d\n" , ret); + } + + ret =visionox_rm69299_power_off (ctx); +if (ret <0 ) +DRM_DEV_ERROR (ctx->dev,"power_off failed ret = %d\n" , ret); + + ctx->prepared = false; +return ret; +} + +static int visionox_rm69299_prepare (struct drm_panel *panel) +{ +struct visionox_rm69299 *ctx =panel_to_ctx (panel); +int ret; +int i; +const struct cmd_set *panel_on_cmds; +const struct rm69299_config *config; +u32 num_cmds; + +if (ctx->prepared) +return 0 ; + + ret =visionox_35597_power_on (ctx); +if (ret <0 ) +return ret; + + ctx->dsi->mode_flags |=MIPI_DSI_MODE_LPM ; + + config = ctx->config; + panel_on_cmds = config->panel_on_cmds; + num_cmds = config->num_on_cmds; + +for (i =0 ; i < num_cmds; i++) { + ret =visionox_dcs_write_buf (panel, + panel_on_cmds[i].size, + panel_on_cmds[i].commands); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev, +"cmd set tx failed i = %d ret = %d\n" , + i, ret); + goto power_off; + } + } + + ret =visionox_dcs_write (panel,MIPI_DCS_EXIT_SLEEP_MODE ); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev, +"exit_sleep_mode cmd failed ret = %d\n" , + ret); + goto power_off; + } + +/* Per DSI spec wait 120ms after sending exit sleep DCS command */ +msleep (120 ); + + ret =visionox_dcs_write (panel,MIPI_DCS_SET_DISPLAY_ON ); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev, +"set_display_on cmd failed ret = %d\n" , ret); + goto power_off; + } + +/* Per DSI spec wait 120ms after sending set_display_on DCS command */ +msleep (120 ); + + ctx->prepared = true; + +return 0 ; + +power_off: +if (visionox_rm69299_power_off (ctx)) +DRM_DEV_ERROR (ctx->dev,"power_off failed\n" ); +return ret; +} + +static int visionox_rm69299_enable (struct drm_panel *panel) +{ +struct visionox_rm69299 *ctx =panel_to_ctx (panel); +int ret; + +if (ctx->enabled) +return 0 ; + +if (ctx->backlight) { + ret =backlight_enable (ctx->backlight); +if (ret <0 ) +DRM_DEV_ERROR (ctx->dev,"backlight enable failed %d\n" , + ret); + } + + ctx->enabled = true; + +return 0 ; +} + +static int visionox_rm69299_get_modes (struct drm_panel *panel) +{ +struct drm_connector *connector = panel->connector; +struct visionox_rm69299 *ctx =panel_to_ctx (panel); +struct drm_display_mode *mode; +const struct rm69299_config *config; + + config = ctx->config; + mode =drm_mode_create (connector->dev); +if (!mode) { +DRM_DEV_ERROR (ctx->dev, +"failed to create a new display mode\n" ); +return 0 ; + } + + connector->display_info.width_mm = config->width_mm; + connector->display_info.height_mm = config->height_mm; +drm_mode_copy (mode, config->dm); + mode->type =DRM_MODE_TYPE_DRIVER |DRM_MODE_TYPE_PREFERRED ; +drm_mode_probed_add (connector, mode); + +return 1 ; +} + +static const struct drm_panel_funcs visionox_rm69299_drm_funcs = { + .disable = visionox_rm69299_disable, + .unprepare = visionox_rm69299_unprepare, + .prepare = visionox_rm69299_prepare, + .enable = visionox_rm69299_enable, + .get_modes = visionox_rm69299_get_modes, +}; + +static int visionox_rm69299_panel_add (struct visionox_rm69299 *ctx) +{ +struct device *dev = ctx->dev; +int ret, i; +const struct rm69299_config *config; + + config = ctx->config; +for (i =0 ; i <ARRAY_SIZE (ctx->supplies); i++) + ctx->supplies[i].supply = regulator_names[i]; + + ret =devm_regulator_bulk_get (dev,ARRAY_SIZE (ctx->supplies), + ctx->supplies); +if (ret <0 ) +return ret; + + ctx->reset_gpio =devm_gpiod_get (dev,"reset" ,GPIOD_OUT_LOW ); +if (IS_ERR (ctx->reset_gpio)) { +DRM_DEV_ERROR (dev,"cannot get reset gpio %ld\n" , +PTR_ERR (ctx->reset_gpio)); +return PTR_ERR (ctx->reset_gpio); + } + + ret =gpiod_direction_output (ctx->reset_gpio,0 ); +if (ret <0 ) { +pr_err ("direction output failed \n" ); + } + +drm_panel_init (&ctx->panel); + ctx->panel.dev = dev; + ctx->panel.funcs = &visionox_rm69299_drm_funcs; +drm_panel_add (&ctx->panel); + +return 0 ; +} + +static const struct drm_display_mode qcom_sc7180_mtp_1080p_mode = { + .name ="1080x2248" , + .clock =158695 , + .hdisplay =1080 , + .hsync_start =1080 +26 , + .hsync_end =1080 +26 +2 , + .htotal =1080 +26 +2 +36 , + .vdisplay =2248 , + .vsync_start =2248 +56 , + .vsync_end =2248 +56 +4 , + .vtotal =2248 +56 +4 +4 , + .vrefresh =60 , + .flags =0 , +}; + +static const struct rm69299_config rm69299_dir = { + .width_mm =74 , + .height_mm =131 , + .panel_name ="qcom_sc7180_mtp_1080p_panel" , + .dm = &qcom_sc7180_mtp_1080p_mode, + .panel_on_cmds = qcom_rm69299_1080p_panel_magic_cmds, + .num_on_cmds =ARRAY_SIZE (qcom_rm69299_1080p_panel_magic_cmds), +}; + +static int visionox_rm69299_probe (struct mipi_dsi_device *dsi) +{ +struct device *dev = &dsi->dev; +struct visionox_rm69299 *ctx; +int ret =0 ; + + ctx =devm_kzalloc (dev,sizeof (*ctx),GFP_KERNEL ); + +if (!ctx) +return -ENOMEM ; + + ctx->config =of_device_get_match_data (dev); + +if (!ctx->config) { +dev_err (dev,"missing device configuration\n" ); +return -ENODEV ; + } + +mipi_dsi_set_drvdata (dsi, ctx); + + ctx->dev = dev; + ctx->dsi = dsi; + + ret =visionox_rm69299_panel_add (ctx); +if (ret) { +DRM_DEV_ERROR (dev,"failed to add panel\n" ); + goto err_panel_add; + } + + dsi->lanes =4 ; + dsi->format =MIPI_DSI_FMT_RGB888 ; + dsi->mode_flags =MIPI_DSI_MODE_VIDEO |MIPI_DSI_MODE_LPM | +MIPI_DSI_CLOCK_NON_CONTINUOUS ; + ret =mipi_dsi_attach (dsi); +if (ret <0 ) { +DRM_DEV_ERROR (dev, +"dsi attach failed ret = %d\n" , ret); + goto err_dsi_attach; + } + +return 0 ; + +err_dsi_attach: +drm_panel_remove (&ctx->panel); +err_panel_add: +mipi_dsi_device_unregister (dsi); +return ret; +} + +static int visionox_rm69299_remove (struct mipi_dsi_device *dsi) +{ +struct visionox_rm69299 *ctx =mipi_dsi_get_drvdata (dsi); + +if (ctx->dsi) { +mipi_dsi_detach (ctx->dsi); +mipi_dsi_device_unregister (ctx->dsi); + } + +drm_panel_remove (&ctx->panel); +return 0 ; +} + +static const struct of_device_id visionox_rm69299_of_match[] = { + { + .compatible ="visionox,rm69299-1080p-display" , + .data = &rm69299_dir, + }, + { } +}; +MODULE_DEVICE_TABLE (of, visionox_rm69299_of_match); + +static struct mipi_dsi_driver visionox_rm69299_driver = { + .driver = { + .name ="panel-visionox-rm69299" , + .of_match_table = visionox_rm69299_of_match, + }, + .probe = visionox_rm69299_probe, + .remove = visionox_rm69299_remove, +}; +module_mipi_dsi_driver (visionox_rm69299_driver); + +MODULE_DESCRIPTION ("VISIONOX RM69299 DSI Panel Driver" ); +MODULE_LICENSE ("GPL v2" ); --
Quoted 2 lines
2.7.4
_______________________________________________
Freedreno mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/freedreno
PATCH 2/2 drm/msm: add DSI config changes to support DSI version
In reply to Harigovindan PAdd DSI config changes to support DSI version.
--- drivers/gpu/drm/msm/dsi/dsi_cfg.c | 21 +++++++++++++++++++++ drivers/gpu/drm/msm/dsi/dsi_cfg.h | 1 + 2 files changed, 22 insertions(+)
drivers/gpu/drm/msm/dsi/dsi_cfg.c +21 -0
@@ -133,6 +133,10 @@ static const char * const dsi_sdm845_bus_clk_names[] = { "iface", "bus", }; +static const char *const dsi_sc7180_bus_clk_names[] = { +"iface" ,"bus" , +}; +static const struct msm_dsi_config sdm845_dsi_cfg = { .io_offset =DSI_6G_REG_SHIFT , .reg_cfg = {
@@ -147,6 +151,20 @@ static const struct msm_dsi_config sdm845_dsi_cfg = { .num_dsi = 2, }; +static const struct msm_dsi_config sc7180_dsi_cfg = { + .io_offset =DSI_6G_REG_SHIFT , + .reg_cfg = { + .num =1 , + .regs = { + {"vdda" ,21800 ,4 },/* 1.2 V */ + }, + }, + .bus_clk_names = dsi_sc7180_bus_clk_names, + .num_bus_clks =ARRAY_SIZE (dsi_sc7180_bus_clk_names), + .io_start = {0xae94000 }, + .num_dsi =1 , +}; +const static struct msm_dsi_host_cfg_ops msm_dsi_v2_host_ops = { .link_clk_enable = dsi_link_clk_enable_v2, .link_clk_disable = dsi_link_clk_disable_v2,
@@ -201,6 +219,9 @@ static const struct msm_dsi_cfg_handler dsi_cfg_handlers[] = { &msm8998_dsi_cfg, &msm_dsi_6g_v2_host_ops}, {MSM_DSI_VER_MAJOR_6G ,MSM_DSI_6G_VER_MINOR_V2_2_1 , &sdm845_dsi_cfg, &msm_dsi_6g_v2_host_ops}, + {MSM_DSI_VER_MAJOR_6G, MSM_DSI_6G_VER_MINOR_V2_4_1, + &sc7180_dsi_cfg, &msm_dsi_6g_v2_host_ops}, + };const struct msm_dsi_cfg_handler *msm_dsi_cfg_get (u32 major,u32 minor)
drivers/gpu/drm/msm/dsi/dsi_cfg.h +1 -0
@@ -19,6 +19,7 @@#define MSM_DSI_6G_VER_MINOR_V1_4_1 0x10040001#define MSM_DSI_6G_VER_MINOR_V2_2_0 0x20000000#define MSM_DSI_6G_VER_MINOR_V2_2_1 0x20020001 +#define MSM_DSI_6G_VER_MINOR_V2_4_1 0x20040001#define MSM_DSI_V2_VER_MINOR_8064 0x0
Signature · 1 line
2.7.4
Re: [PATCH v1 2/2] drm/msm: add DSI config changes to support DSI version
Quoted 4 lines · Harigovindan P
Add DSI config changes to support DSI version.
Signed-off-by Harigovindan P <[email protected]>
For patch 1/2 with the panel driver, probably best to split that out into a different patch(set), since panel drivers are merged into drm-next via a different tree
BR,
-R
Quoted 64 lines
--- drivers/gpu/drm/msm/dsi/dsi_cfg.c | 21 +++++++++++++++++++++ drivers/gpu/drm/msm/dsi/dsi_cfg.h | 1 + 2 files changed, 22 insertions(+)drivers/gpu/drm/msm/dsi/dsi_cfg.c +21
-0@@ -133,6 +133,10 @@ static const char * const dsi_sdm845_bus_clk_names[] = { "iface", "bus", }; +static const char *const dsi_sc7180_bus_clk_names[] = { +"iface" ,"bus" , +}; +static const struct msm_dsi_config sdm845_dsi_cfg = { .io_offset =DSI_6G_REG_SHIFT , .reg_cfg = {@@ -147,6 +151,20 @@ static const struct msm_dsi_config sdm845_dsi_cfg = { .num_dsi = 2, }; +static const struct msm_dsi_config sc7180_dsi_cfg = { + .io_offset =DSI_6G_REG_SHIFT , + .reg_cfg = { + .num =1 , + .regs = { + {"vdda" ,21800 ,4 },/* 1.2 V */ + }, + }, + .bus_clk_names = dsi_sc7180_bus_clk_names, + .num_bus_clks =ARRAY_SIZE (dsi_sc7180_bus_clk_names), + .io_start = {0xae94000 }, + .num_dsi =1 , +}; +const static struct msm_dsi_host_cfg_ops msm_dsi_v2_host_ops = { .link_clk_enable = dsi_link_clk_enable_v2, .link_clk_disable = dsi_link_clk_disable_v2,@@ -201,6 +219,9 @@ static const struct msm_dsi_cfg_handler dsi_cfg_handlers[] = { &msm8998_dsi_cfg, &msm_dsi_6g_v2_host_ops}, {MSM_DSI_VER_MAJOR_6G ,MSM_DSI_6G_VER_MINOR_V2_2_1 , &sdm845_dsi_cfg, &msm_dsi_6g_v2_host_ops}, + {MSM_DSI_VER_MAJOR_6G, MSM_DSI_6G_VER_MINOR_V2_4_1, + &sc7180_dsi_cfg, &msm_dsi_6g_v2_host_ops}, + };const struct msm_dsi_cfg_handler *msm_dsi_cfg_get (u32 major,u32 minor)drivers/gpu/drm/msm/dsi/dsi_cfg.h +1
-1@@ -19,6 +19,7 @@#define MSM_DSI_6G_VER_MINOR_V1_4_1 0x10040001#define MSM_DSI_6G_VER_MINOR_V2_2_0 0x20000000#define MSM_DSI_6G_VER_MINOR_V2_2_1 0x20020001 +#define MSM_DSI_6G_VER_MINOR_V2_4_1 0x20040001#define MSM_DSI_V2_VER_MINOR_8064 0x0 --
Quoted 2 lines
2.7.4
_______________________________________________
Freedreno mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/freedreno
Re: [Freedreno] [PATCH v1 2/2] drm/msm: add DSI config changes to support DSI version
Quoted 8 lines · Rob Clark
Quoted 4 lines · Harigovindan P
Add DSI config changes to support DSI version.
Signed-off-by Harigovindan P <[email protected]>Reviewed-by Rob Clark <[email protected]>
Can we fix the subject/commit text for this to indicate what DSI version and/or SoC this is for? This is a SoC enablement patch, but at first I thought this was some bug fix or something.
Quoted 78 lines
For patch 1/2 with the panel driver, probably best to split that out into a different patch(set), since panel drivers are merged into drm-next via a different tree
BR,
-RQuoted 64 lines
--- drivers/gpu/drm/msm/dsi/dsi_cfg.c | 21 +++++++++++++++++++++ drivers/gpu/drm/msm/dsi/dsi_cfg.h | 1 + 2 files changed, 22 insertions(+)drivers/gpu/drm/msm/dsi/dsi_cfg.c +21
-0@@ -133,6 +133,10 @@ static const char * const dsi_sdm845_bus_clk_names[] = { "iface", "bus", }; +static const char *const dsi_sc7180_bus_clk_names[] = { +"iface" ,"bus" , +}; +static const struct msm_dsi_config sdm845_dsi_cfg = { .io_offset =DSI_6G_REG_SHIFT , .reg_cfg = {@@ -147,6 +151,20 @@ static const struct msm_dsi_config sdm845_dsi_cfg = { .num_dsi = 2, }; +static const struct msm_dsi_config sc7180_dsi_cfg = { + .io_offset =DSI_6G_REG_SHIFT , + .reg_cfg = { + .num =1 , + .regs = { + {"vdda" ,21800 ,4 },/* 1.2 V */ + }, + }, + .bus_clk_names = dsi_sc7180_bus_clk_names, + .num_bus_clks =ARRAY_SIZE (dsi_sc7180_bus_clk_names), + .io_start = {0xae94000 }, + .num_dsi =1 , +}; +const static struct msm_dsi_host_cfg_ops msm_dsi_v2_host_ops = { .link_clk_enable = dsi_link_clk_enable_v2, .link_clk_disable = dsi_link_clk_disable_v2,@@ -201,6 +219,9 @@ static const struct msm_dsi_cfg_handler dsi_cfg_handlers[] = { &msm8998_dsi_cfg, &msm_dsi_6g_v2_host_ops}, {MSM_DSI_VER_MAJOR_6G ,MSM_DSI_6G_VER_MINOR_V2_2_1 , &sdm845_dsi_cfg, &msm_dsi_6g_v2_host_ops}, + {MSM_DSI_VER_MAJOR_6G, MSM_DSI_6G_VER_MINOR_V2_4_1, + &sc7180_dsi_cfg, &msm_dsi_6g_v2_host_ops}, + };const struct msm_dsi_cfg_handler *msm_dsi_cfg_get (u32 major,u32 minor)drivers/gpu/drm/msm/dsi/dsi_cfg.h +1
-1@@ -19,6 +19,7 @@#define MSM_DSI_6G_VER_MINOR_V1_4_1 0x10040001#define MSM_DSI_6G_VER_MINOR_V2_2_0 0x20000000#define MSM_DSI_6G_VER_MINOR_V2_2_1 0x20020001 +#define MSM_DSI_6G_VER_MINOR_V2_4_1 0x20040001#define MSM_DSI_V2_VER_MINOR_8064 0x0 --Quoted 2 lines
2.7.4
_______________________________________________
Freedreno mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/freedreno
Quoting Harigovindan P (2019-11-14 02:16:26)
Quoted 6 lines
Current patchset adds support for rm69299 visionox panel driver used in MSM reference platforms and also adds DSI config that supports the respective DSI version.
The visionox panel driver supports a resolution of 1080x2248 with 4 lanes and supports only single DSI mode.
Current patchset is tested on actual panel.
Do you have the DT binding patch?