ARM: dts: dra7: add cal nodes
Subsystems (8)
v4 cover ARM: dts: dra7: add cal nodes
This patch series adds the needed clkctrl and ty-sysc nodes for CAL module. It also adds support for the module in related dtsi and dts for DRA72, DRA76 and AM654 SoC.
Changes since v3:
- Added Tony's ack
- Added Rob's ack
- In all 3 .dts patch removed unneeded cal 'status = "ok"' lines
Changes since v2:
- Add non-standard clock node naming to commit message as per Tony's comment
Changes since v1:
- Fix clock name to make it generic
- Updated the binding to use ti,camerrx-control instead of sycon_camerrx
- Split off the clk code into its own patch
- Add clk mailing list as requested
Benoit Parrot (10):
clk: ti: dra7: add cam clkctrl data
ARM: dts: dra7: add cam clkctrl node
ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
ARM: dts: dra7-l4: Add ti-sysc node for CAM
ARM: dts: DRA72: Add CAL dtsi node
arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
arm: dtsi: dra76x: Add CAL dtsi node
arm: dts: dra76-evm: Add CAL and OV5640 nodes
arm64: dts: k3-am65-main Add CAL node
arm64: dts: k3-am654-base-board: Add CSI2 OV5640 camera
arch/arm/boot/dts/dra7-l4.dtsi | 43 ++++++++++++++++--- arch/arm/boot/dts/dra72-evm-common.dtsi | 31 +++++++++++++ arch/arm/boot/dts/dra72x.dtsi | 42 ++++++++++++++++++ arch/arm/boot/dts/dra76-evm.dts | 35 +++++++++++++++ arch/arm/boot/dts/dra76x.dtsi | 42 ++++++++++++++++++ arch/arm/boot/dts/dra7xx-clocks.dtsi | 14 ++++++ arch/arm/mach-omap2/clockdomains7xx_data.c | 2 +- arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 22 ++++++++++ .../arm64/boot/dts/ti/k3-am654-base-board.dts | 32 ++++++++++++++ drivers/clk/ti/clk-7xx.c | 19 ++++++++ include/dt-bindings/clock/dra7.h | 10 +++++ 11 files changed, 285 insertions(+), 7 deletions(-)
Signature · 1 line
2.17.1
PATCH v4 1/10 clk: ti: dra7: add cam clkctrl data
Add clkctrl data for CAM domain.
--- drivers/clk/ti/clk-7xx.c | 19 +++++++++++++++++++ include/dt-bindings/clock/dra7.h | 10 ++++++++++ 2 files changed, 29 insertions(+)
drivers/clk/ti/clk-7xx.c +19 -0
@@ -151,6 +151,24 @@ static const struct omap_clkctrl_reg_data dra7_vpe_clkctrl_regs[] __initconst = { 0 }, }; +static const char *const dra7_cam_gfclk_mux_parents[]__initconst = { +"l3_iclk_div" , +"core_iss_main_clk" , +NULL , +}; + +static const struct omap_clkctrl_bit_data dra7_cam_bit_data[]__initconst = { + {24 ,TI_CLK_MUX , dra7_cam_gfclk_mux_parents,NULL }, + {0 }, +}; + +static const struct omap_clkctrl_reg_data dra7_cam_clkctrl_regs[]__initconst = { + {DRA7_CAM_VIP1_CLKCTRL , dra7_cam_bit_data,CLKF_HW_SUP ,"l3_iclk_div" }, + {DRA7_CAM_VIP2_CLKCTRL , dra7_cam_bit_data,CLKF_HW_SUP ,"l3_iclk_div" }, + {DRA7_CAM_VIP3_CLKCTRL , dra7_cam_bit_data,CLKF_HW_SUP ,"l3_iclk_div" }, + {0 }, +}; +static const struct omap_clkctrl_reg_data dra7_coreaon_clkctrl_regs[]__initconst = { {DRA7_COREAON_SMARTREFLEX_MPU_CLKCTRL ,NULL ,CLKF_SW_SUP ,"wkupaon_iclk_mux" }, { DRA7_COREAON_SMARTREFLEX_CORE_CLKCTRL, NULL, CLKF_SW_SUP, "wkupaon_iclk_mux" },
@@ -783,6 +801,7 @@ const struct omap_clkctrl_data dra7_clkctrl_data[] __initconst = { { 0x4a008c00, dra7_atl_clkctrl_regs }, { 0x4a008d20, dra7_l4cfg_clkctrl_regs }, { 0x4a008e20, dra7_l3instr_clkctrl_regs }, + { 0x4a009020, dra7_cam_clkctrl_regs }, { 0x4a009120, dra7_dss_clkctrl_regs }, { 0x4a009320, dra7_l3init_clkctrl_regs }, { 0x4a0093b0, dra7_pcie_clkctrl_regs },
include/dt-bindings/clock/dra7.h +10 -0
@@ -34,6 +34,11 @@#define DRA7_VPE_CLKCTRL_INDEX (offset) ((offset) - DRA7_VPE_CLKCTRL_OFFSET)#define DRA7_VPE_CLKCTRL DRA7_VPE_CLKCTRL_INDEX(0x64) +/* vip clocks */ +#define DRA7_VIP1_CLKCTRL DRA7_CLKCTRL_INDEX(0x20) +#define DRA7_VIP2_CLKCTRL DRA7_CLKCTRL_INDEX(0x28) +#define DRA7_VIP3_CLKCTRL DRA7_CLKCTRL_INDEX(0x30) +/* coreaon clocks */ #define DRA7_SMARTREFLEX_MPU_CLKCTRL DRA7_CLKCTRL_INDEX(0x28)#define DRA7_SMARTREFLEX_CORE_CLKCTRL DRA7_CLKCTRL_INDEX(0x38)
@@ -202,6 +207,11 @@#define DRA7_VPE_CLKCTRL_INDEX (offset) ((offset) - DRA7_VPE_CLKCTRL_OFFSET)#define DRA7_VPE_VPE_CLKCTRL DRA7_VPE_CLKCTRL_INDEX(0x64) +/* vip clocks */ +#define DRA7_CAM_VIP1_CLKCTRL DRA7_CLKCTRL_INDEX(0x20) +#define DRA7_CAM_VIP2_CLKCTRL DRA7_CLKCTRL_INDEX(0x28) +#define DRA7_CAM_VIP3_CLKCTRL DRA7_CLKCTRL_INDEX(0x30) +/* coreaon clocks */ #define DRA7_COREAON_SMARTREFLEX_MPU_CLKCTRL DRA7_CLKCTRL_INDEX(0x28)#define DRA7_COREAON_SMARTREFLEX_CORE_CLKCTRL DRA7_CLKCTRL_INDEX(0x38)
Signature · 1 line
2.17.1
Re: [Patch v4 01/10] clk: ti: dra7: add cam clkctrl data
Quoting Benoit Parrot (2019-12-11 06:05:49)
Quoted 6 lines
Add clkctrl data for CAM domain.
Signed-off-by Benoit Parrot <[email protected]>Acked-by Tony Lindgren <[email protected]>Acked-by Rob Herring <[email protected]>---
Tero Kristo
AppliedRe: [Patch v4 01/10] clk: ti: dra7: add cam clkctrl data
Quoted 10 lines · Stephen Boyd
Quoting Benoit Parrot (2019-12-11 06:05:49)
Quoted 6 lines
Add clkctrl data for CAM domain.
Signed-off-by Benoit Parrot <[email protected]>Acked-by Tony Lindgren <[email protected]>Acked-by Rob Herring <[email protected]>---
Acked-by Stephen Boyd <[email protected]>
Queued this patch towards 5.6, thanks.
-Tero
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
PATCH v4 2/10 ARM: dts: dra7: add cam clkctrl node
In reply to Benoit ParrotAdd clkctrl nodes for CAM domain.
Note that because of the current dts node name dependency for mapping to clock domain, we must still use "cam-clkctrl@" naming instead of generic "clock@" naming for the node. And because of this, it's probably best to apply the dts node addition together along with the other clock changes.
--- arch/arm/boot/dts/dra7xx-clocks.dtsi | 14 ++++++++++++++ 1 file changed, 14 insertions(+)
arch/arm/boot/dts/dra7xx-clocks.dtsi +14 -0
@@ -1734,6 +1734,20 @@ }; }; + cam_cm: cam-cm@1000 { + compatible = "ti,omap4-cm"; + reg = <0x1000 0x100>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x1000 0x100>; + + cam_clkctrl: cam-clkctrl@20 { + compatible = "ti,clkctrl"; + reg = <0x20 0x2c>; + #clock-cells = <2>; + }; + }; + dss_cm: dss-cm@1100 { compatible = "ti,omap4-cm"; reg = <0x1100 0x100>;
Signature · 1 line
2.17.1
PATCH v4 3/10 ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
In reply to Benoit ParrotBoth CAL and VIP rely on this clock domain. But CAL DPHY require LVDSRX_96M_GFCLK to be active. When this domain is set to HWSUP the LVDSRX_96M_GFCLK is on;y active when VIP1 clock is also active. If only CAL on DRA72x (which uses the VIP2 clkctrl) probes the CAM domain is enabled but the LVDSRX_96M_GFCLK is left gated. Since LVDSRX_96M_GFCLK is sourcing the input clock to the DPHY then actual frame capture cannot start as the phy are inactive.
So we either have to also enabled VIP1 even if we don't intend on using it or we need to set the CAM domain to use SWSUP only.
This patch implements the latter.
--- arch/arm/mach-omap2/clockdomains7xx_data.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-omap2/clockdomains7xx_data.c +1 -1
@@ -606,7 +606,7 @@ static struct clockdomain cam_7xx_clkdm = { .dep_bit = DRA7XX_CAM_STATDEP_SHIFT, .wkdep_srcs = cam_wkup_sleep_deps, .sleepdep_srcs = cam_wkup_sleep_deps, - .flags = CLKDM_CAN_HWSUP_SWSUP, + .flags = CLKDM_CAN_SWSUP, };static struct clockdomain l4per_7xx_clkdm = {
Signature · 1 line
2.17.1
PATCH v4 4/10 ARM: dts: dra7-l4: Add ti-sysc node for CAM
In reply to Benoit ParrotAdd CAM nodes as a child of l4 interconnect in order for it to probe using ti-sysc.
--- arch/arm/boot/dts/dra7-l4.dtsi | 43 +++++++++++++++++++++++++++++----- 1 file changed, 37 insertions(+), 6 deletions(-)
arch/arm/boot/dts/dra7-l4.dtsi +37 -6
@@ -4166,27 +4166,58 @@ }; target-module@170000 { /* 0x48970000, ap 21 0a.0 */ - compatible = "ti,sysc"; - status = "disabled"; + compatible = "ti,sysc-omap4", "ti,sysc"; + reg = <0x170010 0x4>; + reg-names = "sysc"; + ti,sysc-midle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + clocks = <&cam_clkctrl DRA7_CAM_VIP1_CLKCTRL 0>; + clock-names = "fck"; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0x170000 0x10000>; + status = "disabled"; }; target-module@190000 { /* 0x48990000, ap 23 2e.0 */ - compatible = "ti,sysc"; - status = "disabled"; + compatible = "ti,sysc-omap4", "ti,sysc"; + reg = <0x190010 0x4>; + reg-names = "sysc"; + ti,sysc-midle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + clocks = <&cam_clkctrl DRA7_CAM_VIP2_CLKCTRL 0>; + clock-names = "fck"; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0x190000 0x10000>; + status = "disabled"; }; target-module@1b0000 { /* 0x489b0000, ap 25 34.0 */ - compatible = "ti,sysc"; - status = "disabled"; + compatible = "ti,sysc-omap4", "ti,sysc"; + reg = <0x1b0000 0x4>, + <0x1b0010 0x4>; + reg-names = "rev", "sysc"; + ti,sysc-midle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + clocks = <&cam_clkctrl DRA7_CAM_VIP3_CLKCTRL 0>; + clock-names = "fck"; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0x1b0000 0x10000>; + status = "disabled"; }; target-module@1d0010 { /* 0x489d0000, ap 27 30.0 */
Signature · 1 line
2.17.1
PATCH v4 5/10 ARM: dts: DRA72: Add CAL dtsi node
In reply to Benoit ParrotThis patch adds the required dtsi node to support the Camera Adaptation Layer (CAL) for the DRA72 family of devices.
--- arch/arm/boot/dts/dra72x.dtsi | 42 +++++++++++++++++++++++++++++++++++ 1 file changed, 42 insertions(+)
arch/arm/boot/dts/dra72x.dtsi +42 -0
@@ -17,6 +17,48 @@ }; }; +&l4_per2 { + target-module@5b000 { /* 0x4845b000, ap 59 46.0 */ + compatible = "ti,sysc-omap4", "ti,sysc"; + reg = <0x5b000 0x4>, + <0x5b010 0x4>; + reg-names = "rev", "sysc"; + ti,sysc-midle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>; + clocks = <&cam_clkctrl DRA7_CAM_VIP2_CLKCTRL 0>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x5b000 0x1000>; + + cal: cal@0 { + compatible = "ti,dra72-cal"; + reg = <0x0000 0x400>, + <0x0800 0x40>, + <0x0900 0x40>; + reg-names = "cal_top", + "cal_rx_core0", + "cal_rx_core1"; + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; + ti,camerrx-control = <&scm_conf 0xE94>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi2_0: port@0 { + reg = <0>; + }; + csi2_1: port@1 { + reg = <1>; + }; + }; + }; + }; +}; + &dss { reg = <0x58000000 0x80>, <0x58004054 0x4>,
Signature · 1 line
2.17.1
PATCH v4 6/10 arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
In reply to Benoit ParrotAdd device nodes for CSI2 camera board OV5640.
Add the CAL port nodes with the necessary linkage to the ov5640 nodes.
--- arch/arm/boot/dts/dra72-evm-common.dtsi | 31 +++++++++++++++++++++++++ 1 file changed, 31 insertions(+)
arch/arm/boot/dts/dra72-evm-common.dtsi +31 -0
@@ -187,6 +187,12 @@ gpio = <&gpio5 8 GPIO_ACTIVE_HIGH>; enable-active-high; }; + + clk_ov5640_fixed: clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24000000>; + }; }; &dra7_pmx_core {
@@ -269,6 +275,23 @@ line-name = "vin6_sel_s0"; }; }; + + ov5640@3c { + compatible = "ovti,ov5640"; + reg = <0x3c>; + + clocks = <&clk_ov5640_fixed>; + clock-names = "xclk"; + + port { + csi2_cam0: endpoint { + remote-endpoint = <&csi2_phy0>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + }; + }; &uart1 {
@@ -580,3 +603,11 @@ &pcie1_rc { status = "okay"; }; + +&csi2_0 { + csi2_phy0: endpoint { + remote-endpoint = <&csi2_cam0>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; +};
Signature · 1 line
2.17.1
PATCH v4 7/10 arm: dtsi: dra76x: Add CAL dtsi node
In reply to Benoit ParrotAdd the required dtsi node to support the Camera Adaptation Layer (CAL) for the DRA76 family of devices.
--- arch/arm/boot/dts/dra76x.dtsi | 42 +++++++++++++++++++++++++++++++++++ 1 file changed, 42 insertions(+)
arch/arm/boot/dts/dra76x.dtsi +42 -0
@@ -41,6 +41,48 @@ }; +&l4_per3 { + target-module@1b0000 { /* 0x489b0000, ap 25 34.0 */ + compatible = "ti,sysc-omap4", "ti,sysc"; + reg = <0x1b0000 0x4>, + <0x1b0010 0x4>; + reg-names = "rev", "sysc"; + ti,sysc-midle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>; + clocks = <&cam_clkctrl DRA7_CAM_VIP3_CLKCTRL 0>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x1b0000 0x10000>; + + cal: cal@0 { + compatible = "ti,dra76-cal"; + reg = <0x0000 0x400>, + <0x0800 0x40>, + <0x0900 0x40>; + reg-names = "cal_top", + "cal_rx_core0", + "cal_rx_core1"; + interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; + ti,camerrx-control = <&scm_conf 0x6dc>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi2_0: port@0 { + reg = <0>; + }; + csi2_1: port@1 { + reg = <1>; + }; + }; + }; + }; +}; + /* MCAN interrupts are hard-wired to irqs 67, 68 */ &crossbar_mpu { ti,irqs-skip = <10 67 68 133 139 140>;
Signature · 1 line
2.17.1
PATCH v4 8/10 arm: dts: dra76-evm: Add CAL and OV5640 nodes
In reply to Benoit ParrotAdd device nodes for CSI2 camera board OV5640.
Add the CAL port nodes with the necessary linkage to the ov5640 nodes.
--- arch/arm/boot/dts/dra76-evm.dts | 35 +++++++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+)
arch/arm/boot/dts/dra76-evm.dts +35 -0
@@ -116,6 +116,12 @@ regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; + + clk_ov5640_fixed: clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24000000>; + }; }; &i2c1 {
@@ -317,6 +323,27 @@ }; }; +&i2c5 { + status = "okay"; + clock-frequency = <400000>; + + ov5640@3c { + compatible = "ovti,ov5640"; + reg = <0x3c>; + + clocks = <&clk_ov5640_fixed>; + clock-names = "xclk"; + + port { + csi2_cam0: endpoint { + remote-endpoint = <&csi2_phy0>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + }; +}; + &cpu0 { vdd-supply = <&buck10_reg>; };
@@ -447,3 +474,11 @@ max-bitrate = <5000000>; }; }; + +&csi2_0 { + csi2_phy0: endpoint { + remote-endpoint = <&csi2_cam0>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; +};
Signature · 1 line
2.17.1
PATCH v4 9/10 arm64: dts: k3-am65-main Add CAL node
In reply to Benoit ParrotAdd CAL dtsi node for AM654 device. Including proper power-domains and clock properties.
--- arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+)
arch/arm64/boot/dts/ti/k3-am65-main.dtsi +22 -0
@@ -624,4 +624,26 @@ dma-coherent; interrupts = <GIC_SPI 355 IRQ_TYPE_EDGE_RISING>; }; + + cal: cal@6f03000 { + compatible = "ti,am654-cal"; + reg = <0x0 0x06f03000 0x0 0x400>, + <0x0 0x06f03800 0x0 0x40>; + reg-names = "cal_top", + "cal_rx_core0"; + interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>; + ti,camerrx-control = <&scm_conf 0x40c0>; + clock-names = "fck"; + clocks = <&k3_clks 2 0>; + power-domains = <&k3_pds 2 TI_SCI_PD_EXCLUSIVE>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi2_0: port@0 { + reg = <0>; + }; + }; + }; };
Signature · 1 line
2.17.1
Tero Kristo
AppliedRe: [Patch v4 09/10] arm64: dts: k3-am65-main Add CAL node
Quoted 4 lines · Benoit Parrot
Add CAL dtsi node for AM654 device. Including proper power-domains and clock properties.
Signed-off-by Benoit Parrot <[email protected]>
Queued this and patch #10 up for 5.6, thanks.
-Tero
Quoted 26 lines
--- arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+)arch/arm64/boot/dts/ti/k3-am65-main.dtsi +13
-0@@ -624,4 +624,26 @@ dma-coherent; interrupts = <GIC_SPI 355 IRQ_TYPE_EDGE_RISING>; }; + + cal: cal@6f03000 { + compatible = "ti,am654-cal"; + reg = <0x0 0x06f03000 0x0 0x400>, + <0x0 0x06f03800 0x0 0x40>; + reg-names = "cal_top", + "cal_rx_core0"; + interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>; + ti,camerrx-control = <&scm_conf 0x40c0>; + clock-names = "fck"; + clocks = <&k3_clks 2 0>; + power-domains = <&k3_pds 2 TI_SCI_PD_EXCLUSIVE>; +
arch/arm64/boot/dts/ti/k3-am65-main.dtsi line 649
Quoted 10 lines
arch/arm64/boot/dts/ti/k3-am65-main.dtsi +9
-0+ ports { + #address-cells = <1>; + #size-cells = <0>; + + csi2_0: port@0 { + reg = <0>; + }; + }; + }; };
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
PATCH v4 10/10 arm64: dts: k3-am654-base-board: Add CSI2 OV5640 camera
In reply to Benoit ParrotAdd support for the OV5640 CSI camera:
- add the OV5640 nodes
- add the CAL node linkage
- enable CAL node
--- .../arm64/boot/dts/ti/k3-am654-base-board.dts | 32 +++++++++++++++++++ 1 file changed, 32 insertions(+)
arch/arm64/boot/dts/ti/k3-am654-base-board.dts +32 -0
@@ -53,6 +53,12 @@ gpios = <&wkup_gpio0 27 GPIO_ACTIVE_LOW>; }; }; + + clk_ov5640_fixed: clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24000000>; + }; }; &wkup_pmx0 {
@@ -184,6 +190,23 @@ pinctrl-names = "default"; pinctrl-0 = <&main_i2c1_pins_default>; clock-frequency = <400000>; + + ov5640@3c { + compatible = "ovti,ov5640"; + reg = <0x3c>; + + clocks = <&clk_ov5640_fixed>; + clock-names = "xclk"; + + port { + csi2_cam0: endpoint { + remote-endpoint = <&csi2_phy0>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + }; + }; &main_i2c2 {
@@ -339,3 +362,12 @@ &mailbox0_cluster11 { status = "disabled"; }; + +&csi2_0 { + csi2_phy0: endpoint { + remote-endpoint = <&csi2_cam0>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; +}; +
Signature · 1 line
2.17.1
Tony Lindgren
maintainerQuoted 3 lines · Benoit Parrot
This patch series adds the needed clkctrl and ty-sysc nodes for CAL module. It also adds support for the module in related dtsi and dts for DRA72, DRA76 and AM654 SoC.
Applying these into omap-for-v5.6/ti-sysc-dt-cam on top of Tero's for-5.6-ti-clk branch. It might be too later for v5.6, but we'll see.
Regards,
Tony
Tony Lindgren
maintainerQuoted 8 lines · Tony Lindgren
Quoted 3 lines · Benoit Parrot
This patch series adds the needed clkctrl and ty-sysc nodes for CAL module. It also adds support for the module in related dtsi and dts for DRA72, DRA76 and AM654 SoC.
Applying these into omap-for-v5.6/ti-sysc-dt-cam on top of Tero's for-5.6-ti-clk branch. It might be too later for v5.6, but we'll see.
Actually I'll leave out the k3-am65 dts changes as I don't see acks for those. Tero can pick up those later.
Regards,
Tony
Quoted 10 lines · Tony Lindgren
Quoted 8 lines · Tony Lindgren
Quoted 3 lines · Benoit Parrot
This patch series adds the needed clkctrl and ty-sysc nodes for CAL module. It also adds support for the module in related dtsi and dts for DRA72, DRA76 and AM654 SoC.
Applying these into omap-for-v5.6/ti-sysc-dt-cam on top of Tero's for-5.6-ti-clk branch. It might be too later for v5.6, but we'll see.
Quoted 7 lines
Actually I'll leave out the k3-am65 dts changes as I don't see acks for those. Tero can pick up those later.
Regards,
Tony
Right, I think I also missed the cal clkctrl patch in this series. This series is imho applying against too many different trees (three if I am not mistaken) and should be split up to avoid confusion / not to get lost in mailboxes.
-Tero
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
Quoted 14 lines · Tero Kristo
Quoted 13 lines · Tony Lindgren
Quoted 8 lines · Tony Lindgren
Quoted 3 lines · Benoit Parrot
This patch series adds the needed clkctrl and ty-sysc nodes for CAL module. It also adds support for the module in related dtsi and dts for DRA72, DRA76 and AM654 SoC.
Applying these into omap-for-v5.6/ti-sysc-dt-cam on top of Tero's for-5.6-ti-clk branch. It might be too later for v5.6, but we'll see.
Actually I'll leave out the k3-am65 dts changes as I don't see acks for those. Tero can pick up those later.
Quoted 6 lines
Quoted 4 lines
Regards,
Tony
Right, I think I also missed the cal clkctrl patch in this series. This series is imho applying against too many different trees (three if I am not mistaken) and should be split up to avoid confusion / not to get lost in mailboxes.
Not cal clkctrl but the cal k3 patches. I just assumed all dts patches in this series were against omaps.
Anyways, I am planning to send k3 dts pull v2 today due to dma patches from Peter, so I think I can sneak these also in with that...
-Tero
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki