configs: disable eMMC HS200 support on layerscape platforms
PATCH 1/1 configs: disable eMMC HS200 support on layerscape platforms
The eMMC HS200 speed mode on Layerscape platforms has not been supported properly. The eSDHC clock tuning has not been implemented by now. So disable it until it is supported properly in case of any potential issues.
--- configs/ls1012ardb_tfa_defconfig | 1 - configs/ls1028ardb_tfa_defconfig | 1 - configs/lx2160ardb_tfa_defconfig | 1 - 3 files changed, 3 deletions(-)
configs/ls1012ardb_tfa_defconfig +0 -1
@@ -38,7 +38,6 @@ CONFIG_NET_RANDOM_ETHADDR=y CONFIG_DM=y CONFIG_SATA_CEVA=y CONFIG_DM_MMC=y -CONFIG_MMC_HS200_SUPPORT=y CONFIG_FSL_ESDHC=y CONFIG_MTD=y CONFIG_DM_SPI_FLASH=y
configs/ls1028ardb_tfa_defconfig +0 -1
@@ -45,7 +45,6 @@ CONFIG_I2C_DEFAULT_BUS_NUMBER=0 CONFIG_I2C_MUX=y CONFIG_I2C_MUX_PCA954x=y CONFIG_DM_MMC=y -CONFIG_MMC_HS200_SUPPORT=y CONFIG_FSL_ESDHC=y CONFIG_MTD=y CONFIG_DM_SPI_FLASH=y
configs/lx2160ardb_tfa_defconfig +0 -1
@@ -41,7 +41,6 @@ CONFIG_DM_I2C=y CONFIG_I2C_SET_DEFAULT_BUS_NUM=y CONFIG_I2C_DEFAULT_BUS_NUMBER=0 CONFIG_DM_MMC=y -CONFIG_MMC_HS200_SUPPORT=y CONFIG_FSL_ESDHC=y CONFIG_MTD=y CONFIG_DM_SPI_FLASH=y
Signature · 1 line
2.7.4
PATCH 1/1 configs: disable eMMC HS200 support on layerscape platforms
Any comments?
Thanks!
Best regards,
Yangbo Lu
Quoted 61 lines
-----Original Message-----
From: Yangbo Lu <[email protected]>
Sent: Tuesday, March 3, 2020 10:33 AM
To: u-boot at lists.denx.de; Priyanka Jain <[email protected]>
Cc: Y.b. Lu <[email protected]>
Subject: [PATCH] configs: disable eMMC HS200 support on layerscape platformsThe eMMC HS200 speed mode on Layerscape platforms has not been supported properly. The eSDHC clock tuning has not been implemented by now. So disable it until it is supported properly in case of any potential issues.
Signed-off-by Yangbo Lu <[email protected]>--- configs/ls1012ardb_tfa_defconfig | 1 - configs/ls1028ardb_tfa_defconfig | 1 - configs/lx2160ardb_tfa_defconfig | 1 - 3 files changed, 3 deletions(-)configs/ls1012ardb_tfa_defconfig +0
-1@@ -38,7 +38,6 @@ CONFIG_NET_RANDOM_ETHADDR=y CONFIG_DM=y CONFIG_SATA_CEVA=y CONFIG_DM_MMC=y -CONFIG_MMC_HS200_SUPPORT=y CONFIG_FSL_ESDHC=y CONFIG_MTD=y CONFIG_DM_SPI_FLASH=yconfigs/ls1028ardb_tfa_defconfig +0
-1@@ -45,7 +45,6 @@ CONFIG_I2C_DEFAULT_BUS_NUMBER=0 CONFIG_I2C_MUX=y CONFIG_I2C_MUX_PCA954x=y CONFIG_DM_MMC=y -CONFIG_MMC_HS200_SUPPORT=y CONFIG_FSL_ESDHC=y CONFIG_MTD=y CONFIG_DM_SPI_FLASH=yconfigs/lx2160ardb_tfa_defconfig +0
-2@@ -41,7 +41,6 @@ CONFIG_DM_I2C=y CONFIG_I2C_SET_DEFAULT_BUS_NUM=y CONFIG_I2C_DEFAULT_BUS_NUMBER=0 CONFIG_DM_MMC=y -CONFIG_MMC_HS200_SUPPORT=y CONFIG_FSL_ESDHC=y CONFIG_MTD=y CONFIG_DM_SPI_FLASH=y --2.7.4
PATCH 1/1 configs: disable eMMC HS200 support on layerscape platforms
Hi,
Quoted 18 lines · Y.b. Lu
Any comments?
Thanks!Best regards,
Yangbo LuQuoted 12 lines
-----Original Message-----
From: Yangbo Lu <[email protected]>
Sent: Tuesday, March 3, 2020 10:33 AM
To: u-boot at lists.denx.de; Priyanka Jain <[email protected]>
Cc: Y.b. Lu <[email protected]>
Subject: [PATCH] configs: disable eMMC HS200 support on layerscape platformsThe eMMC HS200 speed mode on Layerscape platforms has not been supported properly. The eSDHC clock tuning has not been implemented by now. So disable it until it is supported properly in case of any potential issues.
If it's not working fine, looks good to me.
BTW, I didn't have tested on its platform. Do you have a plan to fix it?
Quoted 52 lines
Quoted 49 lines
Signed-off-by Yangbo Lu <[email protected]>--- configs/ls1012ardb_tfa_defconfig | 1 - configs/ls1028ardb_tfa_defconfig | 1 - configs/lx2160ardb_tfa_defconfig | 1 - 3 files changed, 3 deletions(-)configs/ls1012ardb_tfa_defconfig +0
-1@@ -38,7 +38,6 @@ CONFIG_NET_RANDOM_ETHADDR=y CONFIG_DM=y CONFIG_SATA_CEVA=y CONFIG_DM_MMC=y -CONFIG_MMC_HS200_SUPPORT=y CONFIG_FSL_ESDHC=y CONFIG_MTD=y CONFIG_DM_SPI_FLASH=yconfigs/ls1028ardb_tfa_defconfig +0
-1@@ -45,7 +45,6 @@ CONFIG_I2C_DEFAULT_BUS_NUMBER=0 CONFIG_I2C_MUX=y CONFIG_I2C_MUX_PCA954x=y CONFIG_DM_MMC=y -CONFIG_MMC_HS200_SUPPORT=y CONFIG_FSL_ESDHC=y CONFIG_MTD=y CONFIG_DM_SPI_FLASH=yconfigs/lx2160ardb_tfa_defconfig +0
-2@@ -41,7 +41,6 @@ CONFIG_DM_I2C=y CONFIG_I2C_SET_DEFAULT_BUS_NUM=y CONFIG_I2C_DEFAULT_BUS_NUMBER=0 CONFIG_DM_MMC=y -CONFIG_MMC_HS200_SUPPORT=y CONFIG_FSL_ESDHC=y CONFIG_MTD=y CONFIG_DM_SPI_FLASH=y --2.7.4
PATCH 1/1 configs: disable eMMC HS200 support on layerscape platforms
Hi Jaehoon,
Quoted 25 lines
-----Original Message-----
From: Jaehoon Chung <[email protected]>
Sent: Thursday, March 19, 2020 5:01 PM
To: Y.b. Lu <[email protected]>; u-boot at lists.denx.de; Priyanka Jain <[email protected]>
Subject: Re: [PATCH] configs: disable eMMC HS200 support on layerscape platformsHi,
Quoted 14 lines · Y.b. Lu
Any comments?
Thanks!Best regards,
Yangbo LuQuoted 8 lines
-----Original Message-----
From: Yangbo Lu <[email protected]>
Sent: Tuesday, March 3, 2020 10:33 AM
To: u-boot at lists.denx.de; Priyanka Jain <[email protected]>
Cc: Y.b. Lu <[email protected]>
Subject: [PATCH] configs: disable eMMC HS200 support on layerscape platforms
Quoted 8 lines
Quoted 4 lines
Quoted 4 lines
The eMMC HS200 speed mode on Layerscape platforms has not been supported properly. The eSDHC clock tuning has not been implemented by now. So disable it until it is supported properly in case of any potential issues.
If it's not working fine, looks good to me.
BTW, I didn't have tested on its platform. Do you have a plan to fix it?
[Yangbo Lu] Because we got issues with HS200 mode in testing, I sent this patch to disable it for now. The tuning support with eSDHC tuning block is in my plan.
Thanks.
Quoted 56 lines
Reviewed-by Jaehoon Chung <[email protected]>Quoted 52 lines
Quoted 49 lines
Signed-off-by Yangbo Lu <[email protected]>--- configs/ls1012ardb_tfa_defconfig | 1 - configs/ls1028ardb_tfa_defconfig | 1 - configs/lx2160ardb_tfa_defconfig | 1 - 3 files changed, 3 deletions(-)configs/ls1012ardb_tfa_defconfig +0
-1@@ -38,7 +38,6 @@ CONFIG_NET_RANDOM_ETHADDR=y CONFIG_DM=y CONFIG_SATA_CEVA=y CONFIG_DM_MMC=y -CONFIG_MMC_HS200_SUPPORT=y CONFIG_FSL_ESDHC=y CONFIG_MTD=y CONFIG_DM_SPI_FLASH=yconfigs/ls1028ardb_tfa_defconfig +0
-1@@ -45,7 +45,6 @@ CONFIG_I2C_DEFAULT_BUS_NUMBER=0 CONFIG_I2C_MUX=y CONFIG_I2C_MUX_PCA954x=y CONFIG_DM_MMC=y -CONFIG_MMC_HS200_SUPPORT=y CONFIG_FSL_ESDHC=y CONFIG_MTD=y CONFIG_DM_SPI_FLASH=yconfigs/lx2160ardb_tfa_defconfig +0
-2@@ -41,7 +41,6 @@ CONFIG_DM_I2C=y CONFIG_I2C_SET_DEFAULT_BUS_NUM=y CONFIG_I2C_DEFAULT_BUS_NUMBER=0 CONFIG_DM_MMC=y -CONFIG_MMC_HS200_SUPPORT=y CONFIG_FSL_ESDHC=y CONFIG_MTD=y CONFIG_DM_SPI_FLASH=y --2.7.4
PATCH 1/1 configs: disable eMMC HS200 support on layerscape platforms
In reply to Yangbo LuQuoted 8 lines
-----Original Message-----
From: U-Boot <[email protected]> On Behalf Of Yangbo Lu
Sent: Tuesday, March 3, 2020 8:03 AM
To: u-boot at lists.denx.de; Priyanka Jain <[email protected]>
Cc: Y.b. Lu <[email protected]>
Subject: [PATCH] configs: disable eMMC HS200 support on layerscape platforms
Quoted 7 lines
The eMMC HS200 speed mode on Layerscape platforms has not been supported properly. The eSDHC clock tuning has not been implemented by now. So disable it until it is supported properly in case of any potential issues.
Signed-off-by Yangbo Lu <[email protected]>---
Applied to u-boot-fsl-qoriq after rebasing. Waiting upstream
Thanks
Priyanka