Skip to contentSkip to conversation

drm/bridge: dw-hdmi: implement bus-format negotiation and YUV420 support

PATCH Applied Neil Armstrong 2 participants 14 messages Mar 4, 2020 – Apr 16, 2020

Subsystems (5)
lore
Share & tools
lore
#0 lore raw

v5 cover drm/bridge: dw-hdmi: implement bus-format negotiation and YUV420 support

Hi Philippe, Heiko, Maxime, Laurent,

A bad negociation was detected on platforms not implementing a bridge on the encoder side, which has been fixed in this version.

Could you check it doesn't break your platforms using dw-hdmi ? Especially patches 1-5.

Thanks,
Neil

This patchset is based on Boris's merged "drm: Add support for bus-format negotiation" patchset to implement full bus-format negotiation for DW-HDMI, including YUV420 support and 10/12/16bit YUV444, YUV422 and RGB. The Color Space Converter support is already implemented.

And the counterpart implementation in the Amlogic Meson VPU dw-hdmi glue :
- basic bus-format negotiation to select YUV444 bus-format as DW-HDMI input
- YUV420 support when HDMI2.0 YUV420 modeset

This is a follow-up from the previous attempts :
- "drm/meson: Add support for HDMI2.0 YUV420 4k60" at [2]
- "drm/meson: Add support for HDMI2.0 4k60" at [3]

Changes since v4 at [7]:
- Cleaned up patch 1
- Added comment on patch 2
- Added commit message on patch 3
- Fixed invalid negociation when encoder is not yet a bridge (seen on allwinner & rockchip platforms) on patch 4
- Fixed invalid defines, handled MEDIA_BUS_FMT_FIXED and cleaned negociation debug on patch 4
- Added tags on patch 5, 6
- Removed meson_venc_hdmi_encoder_get_out_bus_fmts on patch 7
- Add off-list r-b from Jernej

Changes since v3 at [6]:
- Added "Plug atomic state hooks to the default implementation" on drm/bridge: dw-hdmi
- Also added these atomic state hooks in meson-dw-hdmi in patch 7
- Rebased on latest drm-misc-next including patches 1-7 of [1]

Changes since RFC v2 at [5]:
- Added fixes from Jonas, who tested and integrated it for Rockchip SoCs
- Added support for 10/12/16bit tmds clock calculation
- Added support for max_bcp connector property
- Adapted to Boris's v4 patchset
- Fixed typos reported by boris

Changes since RFC v1 at [4]:
- Rewrote negociation using the v2 patchset, including full DW-HDMI fmt negociation

[2] https://patchwork.freedesktop.org/patch/msgid/[email protected]
[3] https://patchwork.freedesktop.org/patch/msgid/[email protected]
[4] https://patchwork.freedesktop.org/patch/msgid/[email protected]
[5] https://patchwork.freedesktop.org/patch/msgid/[email protected]
[6] https://patchwork.freedesktop.org/patch/msgid/[email protected]
[7] https://patchwork.freedesktop.org/patch/msgid/[email protected]

Jonas Karlman (2):
drm/bridge: dw-hdmi: set mtmdsclock for deep color drm/bridge: dw-hdmi: add max bpc connector property

Neil Armstrong (9):
drm/bridge: dw-hdmi: Plug atomic state hooks to the default
implementation
drm/bridge: synopsys: dw-hdmi: add bus format negociation drm/bridge: synopsys: dw-hdmi: allow ycbcr420 modes for >= 0x200a drm/meson: venc: make drm_display_mode const
drm/meson: meson_dw_hdmi: add bridge and switch to drm_bridge_funcs drm/meson: dw-hdmi: stop enforcing input_bus_format drm/meson: venc: add support for YUV420 setup
drm/meson: vclk: add support for YUV420 setup
drm/meson: Add YUV420 output support

 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 319 +++++++++++++++++++++-
 drivers/gpu/drm/meson/meson_dw_hdmi.c     | 180 +++++++++---
 drivers/gpu/drm/meson/meson_vclk.c        |  93 +++++--
 drivers/gpu/drm/meson/meson_vclk.h        |   7 +-
 drivers/gpu/drm/meson/meson_venc.c        |  10 +-
 drivers/gpu/drm/meson/meson_venc.h        |   4 +-
 drivers/gpu/drm/meson/meson_venc_cvbs.c   |   6 +-
 include/drm/bridge/dw_hdmi.h              |   1 +
 8 files changed, 544 insertions(+), 76 deletions(-)
Signature · 6 lines
2.22.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#1 lore raw

PATCH v5 1/11 drm/bridge: dw-hdmi: set mtmdsclock for deep color

From: Jonas Karlman <[email protected]>

Configure the correct mtmdsclock for deep colors to prepare support for 10, 12 & 16bit output.

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 21 ++++++++++++++++++++-
 1 file changed, 20 insertions(+), 1 deletion(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +20 -1
index 9bad194cfd0a..10f98c9ee77e 100644
@@ -1814,13 +1814,32 @@ static void hdmi_av_composer(struct dw_hdmi *hdmi,
 	int hblank, vblank, h_de_hs, v_de_vs, hsync_len, vsync_len;
 	unsigned int vdisplay, hdisplay;
 
-	vmode->mtmdsclock = vmode->mpixelclock = mode->clock * 1000;
+	vmode->mpixelclock = mode->clock * 1000;
 
 	dev_dbg(hdmi->dev, "final pixclk = %d\n", vmode->mpixelclock);
 
+	vmode->mtmdsclock = vmode->mpixelclock;
+
+	if (!hdmi_bus_fmt_is_yuv422(hdmi->hdmi_data.enc_out_bus_format)) {
+		switch (hdmi_bus_fmt_color_depth(
+				hdmi->hdmi_data.enc_out_bus_format)) {
+		case 16:
+			vmode->mtmdsclock = vmode->mpixelclock * 2;
+			break;
+		case 12:
+			vmode->mtmdsclock = vmode->mpixelclock * 3 / 2;
+			break;
+		case 10:
+			vmode->mtmdsclock = vmode->mpixelclock * 5 / 4;
+			break;
+		}
+	}
+
 	if (hdmi_bus_fmt_is_yuv420(hdmi->hdmi_data.enc_out_bus_format))
 		vmode->mtmdsclock /= 2;
 
+	dev_dbg(hdmi->dev, "final tmdsclock = %d\n", vmode->mtmdsclock);
+
 	/* Set up HDMI_FC_INVIDCONF */
 	inv_val = (hdmi->hdmi_data.hdcp_enable ||
 		   (dw_hdmi_support_scdc(hdmi) &&
Signature · 6 lines
2.22.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#2 lore raw

PATCH v5 2/11 drm/bridge: dw-hdmi: add max bpc connector property

In reply to Neil Armstrong

From: Jonas Karlman <[email protected]>

Add the max_bpc property to the dw-hdmi connector to prepare support for 10, 12 & 16bit output support.

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +8 -0
index 10f98c9ee77e..e097f60e6431 100644
@@ -2414,6 +2414,14 @@ static int dw_hdmi_bridge_attach(struct drm_bridge *bridge,
 				    DRM_MODE_CONNECTOR_HDMIA,
 				    hdmi->ddc);
 
+	/*
+	 * drm_connector_attach_max_bpc_property() requires the
+	 * connector to have a state.
+	 */
+	drm_atomic_helper_connector_reset(connector);
+
+	drm_connector_attach_max_bpc_property(connector, 8, 16);
+
 	if (hdmi->version >= 0x200a && hdmi->plat_data->use_drm_infoframe)
 		drm_object_attach_property(&connector->base,
 			connector->dev->mode_config.hdr_output_metadata_property, 0);
Signature · 1 line
2.22.0
#3 lore raw

PATCH v5 3/11 drm/bridge: dw-hdmi: Plug atomic state hooks to the default implementation

In reply to Neil Armstrong

Add atomic_duplicate_state/atomic_destroy_state/atomic_reset bridge funcs to allow setup of atomic bridge state.

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +3 -0
index e097f60e6431..9f2918898f60 100644
@@ -2506,6 +2506,9 @@ static void dw_hdmi_bridge_enable(struct drm_bridge *bridge)
 }
 
 static const struct drm_bridge_funcs dw_hdmi_bridge_funcs = {
+	.atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
+	.atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
+	.atomic_reset = drm_atomic_helper_bridge_reset,
 	.attach = dw_hdmi_bridge_attach,
 	.detach = dw_hdmi_bridge_detach,
 	.enable = dw_hdmi_bridge_enable,
Signature · 6 lines
2.22.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#4 lore raw

PATCH v5 4/11 drm/bridge: synopsys: dw-hdmi: add bus format negociation

In reply to Neil Armstrong

Add the atomic_get_output_bus_fmts, atomic_get_input_bus_fmts to negociate the possible output and input formats for the current mode and monitor, and use the negotiated formats in a basic atomic_check callback.

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 281 +++++++++++++++++++++-
 1 file changed, 277 insertions(+), 4 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +277 -4
index 9f2918898f60..de19e8993e1d 100644
@@ -2097,11 +2097,10 @@ static int dw_hdmi_setup(struct dw_hdmi *hdmi, struct drm_display_mode *mode)
 	hdmi->hdmi_data.video_mode.mpixelrepetitionoutput = 0;
 	hdmi->hdmi_data.video_mode.mpixelrepetitioninput = 0;
 
-	/* TOFIX: Get input format from plat data or fallback to RGB888 */
 	if (hdmi->plat_data->input_bus_format)
 		hdmi->hdmi_data.enc_in_bus_format =
 			hdmi->plat_data->input_bus_format;
-	else
+	else if (hdmi->hdmi_data.enc_in_bus_format == MEDIA_BUS_FMT_FIXED)
 		hdmi->hdmi_data.enc_in_bus_format = MEDIA_BUS_FMT_RGB888_1X24;
 
 	/* TOFIX: Get input encoding from plat data or fallback to none */
@@ -2111,8 +2110,8 @@ static int dw_hdmi_setup(struct dw_hdmi *hdmi, struct drm_display_mode *mode)
 	else
 		hdmi->hdmi_data.enc_in_encoding = V4L2_YCBCR_ENC_DEFAULT;
 
-	/* TOFIX: Default to RGB888 output format */
-	hdmi->hdmi_data.enc_out_bus_format = MEDIA_BUS_FMT_RGB888_1X24;
+	if (hdmi->hdmi_data.enc_out_bus_format == MEDIA_BUS_FMT_FIXED)
+		hdmi->hdmi_data.enc_out_bus_format = MEDIA_BUS_FMT_RGB888_1X24;
 
 	hdmi->hdmi_data.pix_repet_factor = 0;
 	hdmi->hdmi_data.hdcp_enable = 0;
@@ -2390,6 +2389,277 @@ static const struct drm_connector_helper_funcs dw_hdmi_connector_helper_funcs =
 	.atomic_check = dw_hdmi_connector_atomic_check,
 };
 
+/*
+ * Possible output formats :
+ * - MEDIA_BUS_FMT_UYYVYY16_0_5X48,
+ * - MEDIA_BUS_FMT_UYYVYY12_0_5X36,
+ * - MEDIA_BUS_FMT_UYYVYY10_0_5X30,
+ * - MEDIA_BUS_FMT_UYYVYY8_0_5X24,
+ * - MEDIA_BUS_FMT_YUV16_1X48,
+ * - MEDIA_BUS_FMT_RGB161616_1X48,
+ * - MEDIA_BUS_FMT_UYVY12_1X24,
+ * - MEDIA_BUS_FMT_YUV12_1X36,
+ * - MEDIA_BUS_FMT_RGB121212_1X36,
+ * - MEDIA_BUS_FMT_UYVY10_1X20,
+ * - MEDIA_BUS_FMT_YUV10_1X30,
+ * - MEDIA_BUS_FMT_RGB101010_1X30,
+ * - MEDIA_BUS_FMT_UYVY8_1X16,
+ * - MEDIA_BUS_FMT_YUV8_1X24,
+ * - MEDIA_BUS_FMT_RGB888_1X24,
+ */
+
+/* Can return a maximum of 11 possible output formats for a mode/connector */
+#define MAX_OUTPUT_SEL_FORMATS	11
+
+static u32 *dw_hdmi_bridge_atomic_get_output_bus_fmts(struct drm_bridge *bridge,
+					struct drm_bridge_state *bridge_state,
+					struct drm_crtc_state *crtc_state,
+					struct drm_connector_state *conn_state,
+					unsigned int *num_output_fmts)
+{
+	struct drm_connector *conn = conn_state->connector;
+	struct drm_display_info *info = &conn->display_info;
+	struct drm_display_mode *mode = &crtc_state->mode;
+	u8 max_bpc = conn_state->max_requested_bpc;
+	bool is_hdmi2_sink = info->hdmi.scdc.supported ||
+			     (info->color_formats & DRM_COLOR_FORMAT_YCRCB420);
+	u32 *output_fmts;
+	unsigned int i = 0;
+
+	*num_output_fmts = 0;
+
+	output_fmts = kcalloc(MAX_OUTPUT_SEL_FORMATS, sizeof(*output_fmts),
+			      GFP_KERNEL);
+	if (!output_fmts)
+		return NULL;
+
+	/* If dw-hdmi is the only bridge, avoid negociating with ourselves */
+	if (list_is_singular(&bridge->encoder->bridge_chain)) {
+		*num_output_fmts = 1;
+		output_fmts[0] = MEDIA_BUS_FMT_FIXED;
+
+		return output_fmts;
+	}
+
+	/*
+	 * If the current mode enforces 4:2:0, force the output but format
+	 * to 4:2:0 and do not add the YUV422/444/RGB formats
+	 */
+	if (conn->ycbcr_420_allowed &&
+	    (drm_mode_is_420_only(info, mode) ||
+	     (is_hdmi2_sink && drm_mode_is_420_also(info, mode)))) {
+
+		/* Order bus formats from 16bit to 8bit if supported */
+		if (max_bpc >= 16 && info->bpc == 16 &&
+		    (info->hdmi.y420_dc_modes & DRM_EDID_YCBCR420_DC_48))
+			output_fmts[i++] = MEDIA_BUS_FMT_UYYVYY16_0_5X48;
+
+		if (max_bpc >= 12 && info->bpc >= 12 &&
+		    (info->hdmi.y420_dc_modes & DRM_EDID_YCBCR420_DC_36))
+			output_fmts[i++] = MEDIA_BUS_FMT_UYYVYY12_0_5X36;
+
+		if (max_bpc >= 10 && info->bpc >= 10 &&
+		    (info->hdmi.y420_dc_modes & DRM_EDID_YCBCR420_DC_30))
+			output_fmts[i++] = MEDIA_BUS_FMT_UYYVYY10_0_5X30;
+
+		/* Default 8bit fallback */
+		output_fmts[i++] = MEDIA_BUS_FMT_UYYVYY8_0_5X24;
+
+		*num_output_fmts = i;
+
+		return output_fmts;
+	}
+
+	/*
+	 * Order bus formats from 16bit to 8bit and from YUV422 to RGB
+	 * if supported. In any case the default RGB888 format is added
+	 */
+
+	if (max_bpc >= 16 && info->bpc == 16) {
+		if (info->color_formats & DRM_COLOR_FORMAT_YCRCB444)
+			output_fmts[i++] = MEDIA_BUS_FMT_YUV16_1X48;
+
+		output_fmts[i++] = MEDIA_BUS_FMT_RGB161616_1X48;
+	}
+
+	if (max_bpc >= 12 && info->bpc >= 12) {
+		if (info->color_formats & DRM_COLOR_FORMAT_YCRCB422)
+			output_fmts[i++] = MEDIA_BUS_FMT_UYVY12_1X24;
+
+		if (info->color_formats & DRM_COLOR_FORMAT_YCRCB444)
+			output_fmts[i++] = MEDIA_BUS_FMT_YUV12_1X36;
+
+		output_fmts[i++] = MEDIA_BUS_FMT_RGB121212_1X36;
+	}
+
+	if (max_bpc >= 10 && info->bpc >= 10) {
+		if (info->color_formats & DRM_COLOR_FORMAT_YCRCB422)
+			output_fmts[i++] = MEDIA_BUS_FMT_UYVY10_1X20;
+
+		if (info->color_formats & DRM_COLOR_FORMAT_YCRCB444)
+			output_fmts[i++] = MEDIA_BUS_FMT_YUV10_1X30;
+
+		output_fmts[i++] = MEDIA_BUS_FMT_RGB101010_1X30;
+	}
+
+	if (info->color_formats & DRM_COLOR_FORMAT_YCRCB422)
+		output_fmts[i++] = MEDIA_BUS_FMT_UYVY8_1X16;
+
+	if (info->color_formats & DRM_COLOR_FORMAT_YCRCB444)
+		output_fmts[i++] = MEDIA_BUS_FMT_YUV8_1X24;
+
+	/* Default 8bit RGB fallback */
+	output_fmts[i++] = MEDIA_BUS_FMT_RGB888_1X24;
+
+	*num_output_fmts = i;
+
+	return output_fmts;
+}
+
+/*
+ * Possible input formats :
+ * - MEDIA_BUS_FMT_RGB888_1X24
+ * - MEDIA_BUS_FMT_YUV8_1X24
+ * - MEDIA_BUS_FMT_UYVY8_1X16
+ * - MEDIA_BUS_FMT_UYYVYY8_0_5X24
+ * - MEDIA_BUS_FMT_RGB101010_1X30
+ * - MEDIA_BUS_FMT_YUV10_1X30
+ * - MEDIA_BUS_FMT_UYVY10_1X20
+ * - MEDIA_BUS_FMT_UYYVYY10_0_5X30
+ * - MEDIA_BUS_FMT_RGB121212_1X36
+ * - MEDIA_BUS_FMT_YUV12_1X36
+ * - MEDIA_BUS_FMT_UYVY12_1X24
+ * - MEDIA_BUS_FMT_UYYVYY12_0_5X36
+ * - MEDIA_BUS_FMT_RGB161616_1X48
+ * - MEDIA_BUS_FMT_YUV16_1X48
+ * - MEDIA_BUS_FMT_UYYVYY16_0_5X48
+ */
+
+/* Can return a maximum of 3 possible input formats for an output format */
+#define MAX_INPUT_SEL_FORMATS	3
+
+static u32 *dw_hdmi_bridge_atomic_get_input_bus_fmts(struct drm_bridge *bridge,
+					struct drm_bridge_state *bridge_state,
+					struct drm_crtc_state *crtc_state,
+					struct drm_connector_state *conn_state,
+					u32 output_fmt,
+					unsigned int *num_input_fmts)
+{
+	u32 *input_fmts;
+	unsigned int i = 0;
+
+	*num_input_fmts = 0;
+
+	input_fmts = kcalloc(MAX_INPUT_SEL_FORMATS, sizeof(*input_fmts),
+			     GFP_KERNEL);
+	if (!input_fmts)
+		return NULL;
+
+	switch (output_fmt) {
+	/* If MEDIA_BUS_FMT_FIXED is tested, return default bus format */
+	case MEDIA_BUS_FMT_FIXED:
+		input_fmts[i++] = MEDIA_BUS_FMT_RGB888_1X24;
+		break;
+	/* 8bit */
+	case MEDIA_BUS_FMT_RGB888_1X24:
+		input_fmts[i++] = MEDIA_BUS_FMT_RGB888_1X24;
+		input_fmts[i++] = MEDIA_BUS_FMT_YUV8_1X24;
+		input_fmts[i++] = MEDIA_BUS_FMT_UYVY8_1X16;
+		break;
+	case MEDIA_BUS_FMT_YUV8_1X24:
+		input_fmts[i++] = MEDIA_BUS_FMT_YUV8_1X24;
+		input_fmts[i++] = MEDIA_BUS_FMT_UYVY8_1X16;
+		input_fmts[i++] = MEDIA_BUS_FMT_RGB888_1X24;
+		break;
+	case MEDIA_BUS_FMT_UYVY8_1X16:
+		input_fmts[i++] = MEDIA_BUS_FMT_UYVY8_1X16;
+		input_fmts[i++] = MEDIA_BUS_FMT_YUV8_1X24;
+		input_fmts[i++] = MEDIA_BUS_FMT_RGB888_1X24;
+		break;
+
+	/* 10bit */
+	case MEDIA_BUS_FMT_RGB101010_1X30:
+		input_fmts[i++] = MEDIA_BUS_FMT_RGB101010_1X30;
+		input_fmts[i++] = MEDIA_BUS_FMT_YUV10_1X30;
+		input_fmts[i++] = MEDIA_BUS_FMT_UYVY10_1X20;
+		break;
+	case MEDIA_BUS_FMT_YUV10_1X30:
+		input_fmts[i++] = MEDIA_BUS_FMT_YUV10_1X30;
+		input_fmts[i++] = MEDIA_BUS_FMT_UYVY10_1X20;
+		input_fmts[i++] = MEDIA_BUS_FMT_RGB101010_1X30;
+		break;
+	case MEDIA_BUS_FMT_UYVY10_1X20:
+		input_fmts[i++] = MEDIA_BUS_FMT_UYVY10_1X20;
+		input_fmts[i++] = MEDIA_BUS_FMT_YUV10_1X30;
+		input_fmts[i++] = MEDIA_BUS_FMT_RGB101010_1X30;
+		break;
+
+	/* 12bit */
+	case MEDIA_BUS_FMT_RGB121212_1X36:
+		input_fmts[i++] = MEDIA_BUS_FMT_RGB121212_1X36;
+		input_fmts[i++] = MEDIA_BUS_FMT_YUV12_1X36;
+		input_fmts[i++] = MEDIA_BUS_FMT_UYVY12_1X24;
+		break;
+	case MEDIA_BUS_FMT_YUV12_1X36:
+		input_fmts[i++] = MEDIA_BUS_FMT_YUV12_1X36;
+		input_fmts[i++] = MEDIA_BUS_FMT_UYVY12_1X24;
+		input_fmts[i++] = MEDIA_BUS_FMT_RGB121212_1X36;
+		break;
+	case MEDIA_BUS_FMT_UYVY12_1X24:
+		input_fmts[i++] = MEDIA_BUS_FMT_UYVY12_1X24;
+		input_fmts[i++] = MEDIA_BUS_FMT_YUV12_1X36;
+		input_fmts[i++] = MEDIA_BUS_FMT_RGB121212_1X36;
+		break;
+
+	/* 16bit */
+	case MEDIA_BUS_FMT_RGB161616_1X48:
+		input_fmts[i++] = MEDIA_BUS_FMT_RGB161616_1X48;
+		input_fmts[i++] = MEDIA_BUS_FMT_YUV16_1X48;
+		break;
+	case MEDIA_BUS_FMT_YUV16_1X48:
+		input_fmts[i++] = MEDIA_BUS_FMT_YUV16_1X48;
+		input_fmts[i++] = MEDIA_BUS_FMT_RGB161616_1X48;
+		break;
+
+	/*YUV 4:2:0 */
+	case MEDIA_BUS_FMT_UYYVYY8_0_5X24:
+	case MEDIA_BUS_FMT_UYYVYY10_0_5X30:
+	case MEDIA_BUS_FMT_UYYVYY12_0_5X36:
+	case MEDIA_BUS_FMT_UYYVYY16_0_5X48:
+		input_fmts[i++] = output_fmt;
+		break;
+	}
+
+	*num_input_fmts = i;
+
+	if (*num_input_fmts == 0) {
+		kfree(input_fmts);
+		input_fmts = NULL;
+	}
+
+	return input_fmts;
+}
+
+static int dw_hdmi_bridge_atomic_check(struct drm_bridge *bridge,
+				       struct drm_bridge_state *bridge_state,
+				       struct drm_crtc_state *crtc_state,
+				       struct drm_connector_state *conn_state)
+{
+	struct dw_hdmi *hdmi = bridge->driver_private;
+
+	hdmi->hdmi_data.enc_out_bus_format =
+			bridge_state->output_bus_cfg.format;
+
+	hdmi->hdmi_data.enc_in_bus_format =
+			bridge_state->input_bus_cfg.format;
+
+	dev_dbg(hdmi->dev, "input format 0x%04x, output format 0x%04x\n",
+		bridge_state->input_bus_cfg.format,
+		bridge_state->output_bus_cfg.format);
+
+	return 0;
+}
+
 static int dw_hdmi_bridge_attach(struct drm_bridge *bridge,
 				 enum drm_bridge_attach_flags flags)
 {
@@ -2511,6 +2781,9 @@ static const struct drm_bridge_funcs dw_hdmi_bridge_funcs = {
 	.atomic_reset = drm_atomic_helper_bridge_reset,
 	.attach = dw_hdmi_bridge_attach,
 	.detach = dw_hdmi_bridge_detach,
+	.atomic_check = dw_hdmi_bridge_atomic_check,
+	.atomic_get_output_bus_fmts = dw_hdmi_bridge_atomic_get_output_bus_fmts,
+	.atomic_get_input_bus_fmts = dw_hdmi_bridge_atomic_get_input_bus_fmts,
 	.enable = dw_hdmi_bridge_enable,
 	.disable = dw_hdmi_bridge_disable,
 	.mode_set = dw_hdmi_bridge_mode_set,
Signature · 1 line
2.22.0
#5 lore raw

PATCH v5 5/11 drm/bridge: synopsys: dw-hdmi: allow ycbcr420 modes for >= 0x200a

In reply to Neil Armstrong

Now the DW-HDMI Controller supports the HDMI2.0 modes, enable support for these modes in the connector if the platform supports them. We limit these modes to DW-HDMI IP version >= 0x200a which are designed to support HDMI2.0 display modes.

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 6 ++++++
 include/drm/bridge/dw_hdmi.h              | 1 +
 2 files changed, 7 insertions(+)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +6 -0
index de19e8993e1d..f85c15ad8486 100644
@@ -3252,6 +3252,12 @@ __dw_hdmi_probe(struct platform_device *pdev,
 	hdmi->bridge.of_node = pdev->dev.of_node;
 #endif
 
+	if (hdmi->version >= 0x200a)
+		hdmi->connector.ycbcr_420_allowed =
+			hdmi->plat_data->ycbcr_420_allowed;
+	else
+		hdmi->connector.ycbcr_420_allowed = false;
+
 	memset(&pdevinfo, 0, sizeof(pdevinfo));
 	pdevinfo.parent = dev;
 	pdevinfo.id = PLATFORM_DEVID_AUTO;
include/drm/bridge/dw_hdmi.h +1 -0
index 9d4d5cc47969..0b34a12c4a1c 100644
@@ -129,6 +129,7 @@ struct dw_hdmi_plat_data {
 	unsigned long input_bus_format;
 	unsigned long input_bus_encoding;
 	bool use_drm_infoframe;
+	bool ycbcr_420_allowed;
 
 	/* Vendor PHY support */
 	const struct dw_hdmi_phy_ops *phy_ops;
Signature · 6 lines
2.22.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#6 lore raw

PATCH v5 6/11 drm/meson: venc: make drm_display_mode const

In reply to Neil Armstrong

Before switching to bridge funcs, make sure drm_display_mode is passed as const to the venc functions.

---
 drivers/gpu/drm/meson/meson_venc.c | 2 +-
 drivers/gpu/drm/meson/meson_venc.h | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)
drivers/gpu/drm/meson/meson_venc.c +1 -1
index 4efd7864d5bf..a9ab78970bfe 100644
@@ -946,7 +946,7 @@ bool meson_venc_hdmi_venc_repeat(int vic)
 EXPORT_SYMBOL_GPL(meson_venc_hdmi_venc_repeat);
 
 void meson_venc_hdmi_mode_set(struct meson_drm *priv, int vic,
-			      struct drm_display_mode *mode)
+			      const struct drm_display_mode *mode)
 {
 	union meson_hdmi_venc_mode *vmode = NULL;
 	union meson_hdmi_venc_mode vmode_dmt;
drivers/gpu/drm/meson/meson_venc.h +1 -1
index 576768bdd08d..1abdcbdf51c0 100644
@@ -60,7 +60,7 @@ extern struct meson_cvbs_enci_mode meson_cvbs_enci_ntsc;
 void meson_venci_cvbs_mode_set(struct meson_drm *priv,
 			       struct meson_cvbs_enci_mode *mode);
 void meson_venc_hdmi_mode_set(struct meson_drm *priv, int vic,
-			      struct drm_display_mode *mode);
+			      const struct drm_display_mode *mode);
 unsigned int meson_venci_get_field(struct meson_drm *priv);
 
 void meson_venc_enable_vsync(struct meson_drm *priv);
Signature · 6 lines
2.22.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#7 lore raw

PATCH v5 7/11 drm/meson: meson_dw_hdmi: add bridge and switch to drm_bridge_funcs

In reply to Neil Armstrong

Switch the dw-hdmi driver to drm_bridge_funcs by implementing a new local bridge, connecting it to the dw-hdmi bridge, then implement the atomic_get_input_bus_fmts/atomic_get_output_bus_fmts.

---
 drivers/gpu/drm/meson/meson_dw_hdmi.c | 85 ++++++++++++++++++++-------
 1 file changed, 65 insertions(+), 20 deletions(-)
drivers/gpu/drm/meson/meson_dw_hdmi.c +65 -20
index 3bb7ffe5fc39..8f51d032262c 100644
@@ -16,6 +16,7 @@
 
 #include <drm/bridge/dw_hdmi.h>
 #include <drm/drm_atomic_helper.h>
+#include <drm/drm_bridge.h>
 #include <drm/drm_device.h>
 #include <drm/drm_edid.h>
 #include <drm/drm_probe_helper.h>
@@ -135,6 +136,7 @@ struct meson_dw_hdmi_data {
 
 struct meson_dw_hdmi {
 	struct drm_encoder encoder;
+	struct drm_bridge bridge;
 	struct dw_hdmi_plat_data dw_plat_data;
 	struct meson_drm *priv;
 	struct device *dev;
@@ -151,6 +153,8 @@ struct meson_dw_hdmi {
 };
 #define encoder_to_meson_dw_hdmi(x) \
 	container_of(x, struct meson_dw_hdmi, encoder)
+#define bridge_to_meson_dw_hdmi(x) \
+	container_of(x, struct meson_dw_hdmi, bridge)
 
 static inline int dw_hdmi_is_compatible(struct meson_dw_hdmi *dw_hdmi,
 					const char *compat)
@@ -368,7 +372,7 @@ static inline void meson_dw_hdmi_phy_reset(struct meson_dw_hdmi *dw_hdmi)
 }
 
 static void dw_hdmi_set_vclk(struct meson_dw_hdmi *dw_hdmi,
-			     struct drm_display_mode *mode)
+			     const struct drm_display_mode *mode)
 {
 	struct meson_drm *priv = dw_hdmi->priv;
 	int vic = drm_match_cea_mode(mode);
@@ -663,6 +667,10 @@ dw_hdmi_mode_valid(struct drm_connector *connector,
 
 /* Encoder */
 
+static const u32 meson_dw_hdmi_out_bus_fmts[] = {
+	MEDIA_BUS_FMT_YUV8_1X24,
+};
+
 static void meson_venc_hdmi_encoder_destroy(struct drm_encoder *encoder)
 {
 	drm_encoder_cleanup(encoder);
@@ -672,16 +680,43 @@ static const struct drm_encoder_funcs meson_venc_hdmi_encoder_funcs = {
 	.destroy        = meson_venc_hdmi_encoder_destroy,
 };
 
-static int meson_venc_hdmi_encoder_atomic_check(struct drm_encoder *encoder,
+static u32 *
+meson_venc_hdmi_encoder_get_inp_bus_fmts(struct drm_bridge *bridge,
+					struct drm_bridge_state *bridge_state,
+					struct drm_crtc_state *crtc_state,
+					struct drm_connector_state *conn_state,
+					u32 output_fmt,
+					unsigned int *num_input_fmts)
+{
+	u32 *input_fmts = NULL;
+
+	if (output_fmt == meson_dw_hdmi_out_bus_fmts[0]) {
+		*num_input_fmts = 1;
+		input_fmts = kcalloc(*num_input_fmts,
+				     sizeof(*input_fmts),
+				     GFP_KERNEL);
+		if (!input_fmts)
+			return NULL;
+
+		input_fmts[0] = output_fmt;
+	} else {
+		*num_input_fmts = 0;
+	}
+
+	return input_fmts;
+}
+
+static int meson_venc_hdmi_encoder_atomic_check(struct drm_bridge *bridge,
+					struct drm_bridge_state *bridge_state,
 					struct drm_crtc_state *crtc_state,
 					struct drm_connector_state *conn_state)
 {
 	return 0;
 }
 
-static void meson_venc_hdmi_encoder_disable(struct drm_encoder *encoder)
+static void meson_venc_hdmi_encoder_disable(struct drm_bridge *bridge)
 {
-	struct meson_dw_hdmi *dw_hdmi = encoder_to_meson_dw_hdmi(encoder);
+	struct meson_dw_hdmi *dw_hdmi = bridge_to_meson_dw_hdmi(bridge);
 	struct meson_drm *priv = dw_hdmi->priv;
 
 	DRM_DEBUG_DRIVER("\n");
@@ -693,9 +728,9 @@ static void meson_venc_hdmi_encoder_disable(struct drm_encoder *encoder)
 	writel_relaxed(0, priv->io_base + _REG(ENCP_VIDEO_EN));
 }
 
-static void meson_venc_hdmi_encoder_enable(struct drm_encoder *encoder)
+static void meson_venc_hdmi_encoder_enable(struct drm_bridge *bridge)
 {
-	struct meson_dw_hdmi *dw_hdmi = encoder_to_meson_dw_hdmi(encoder);
+	struct meson_dw_hdmi *dw_hdmi = bridge_to_meson_dw_hdmi(bridge);
 	struct meson_drm *priv = dw_hdmi->priv;
 
 	DRM_DEBUG_DRIVER("%s\n", priv->venc.hdmi_use_enci ? "VENCI" : "VENCP");
@@ -706,11 +741,11 @@ static void meson_venc_hdmi_encoder_enable(struct drm_encoder *encoder)
 		writel_relaxed(1, priv->io_base + _REG(ENCP_VIDEO_EN));
 }
 
-static void meson_venc_hdmi_encoder_mode_set(struct drm_encoder *encoder,
-				   struct drm_display_mode *mode,
-				   struct drm_display_mode *adjusted_mode)
+static void meson_venc_hdmi_encoder_mode_set(struct drm_bridge *bridge,
+				   const struct drm_display_mode *mode,
+				   const struct drm_display_mode *adjusted_mode)
 {
-	struct meson_dw_hdmi *dw_hdmi = encoder_to_meson_dw_hdmi(encoder);
+	struct meson_dw_hdmi *dw_hdmi = bridge_to_meson_dw_hdmi(bridge);
 	struct meson_drm *priv = dw_hdmi->priv;
 	int vic = drm_match_cea_mode(mode);
 
@@ -726,12 +761,15 @@ static void meson_venc_hdmi_encoder_mode_set(struct drm_encoder *encoder,
 	writel_relaxed(0, priv->io_base + _REG(VPU_HDMI_FMT_CTRL));
 }
 
-static const struct drm_encoder_helper_funcs
-				meson_venc_hdmi_encoder_helper_funcs = {
-	.atomic_check	= meson_venc_hdmi_encoder_atomic_check,
-	.disable	= meson_venc_hdmi_encoder_disable,
-	.enable		= meson_venc_hdmi_encoder_enable,
-	.mode_set	= meson_venc_hdmi_encoder_mode_set,
+static const struct drm_bridge_funcs meson_venc_hdmi_encoder_bridge_funcs = {
+	.atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
+	.atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
+	.atomic_get_input_bus_fmts = meson_venc_hdmi_encoder_get_inp_bus_fmts,
+	.atomic_reset = drm_atomic_helper_bridge_reset,
+	.atomic_check = meson_venc_hdmi_encoder_atomic_check,
+	.enable	= meson_venc_hdmi_encoder_enable,
+	.disable = meson_venc_hdmi_encoder_disable,
+	.mode_set = meson_venc_hdmi_encoder_mode_set,
 };
 
 /* DW HDMI Regmap */
@@ -852,6 +890,7 @@ static int meson_dw_hdmi_bind(struct device *dev, struct device *master,
 	struct drm_device *drm = data;
 	struct meson_drm *priv = drm->dev_private;
 	struct dw_hdmi_plat_data *dw_plat_data;
+	struct drm_bridge *next_bridge;
 	struct drm_encoder *encoder;
 	struct resource *res;
 	int irq;
@@ -953,8 +992,6 @@ static int meson_dw_hdmi_bind(struct device *dev, struct device *master,
 
 	/* Encoder */
 
-	drm_encoder_helper_add(encoder, &meson_venc_hdmi_encoder_helper_funcs);
-
 	ret = drm_encoder_init(drm, encoder, &meson_venc_hdmi_encoder_funcs,
 			       DRM_MODE_ENCODER_TMDS, "meson_hdmi");
 	if (ret) {
@@ -962,6 +999,9 @@ static int meson_dw_hdmi_bind(struct device *dev, struct device *master,
 		return ret;
 	}
 
+	meson_dw_hdmi->bridge.funcs = &meson_venc_hdmi_encoder_bridge_funcs;
+	drm_bridge_attach(encoder, &meson_dw_hdmi->bridge, NULL, 0);
+
 	encoder->possible_crtcs = BIT(0);
 
 	DRM_DEBUG_DRIVER("encoder initialized\n");
@@ -984,11 +1024,16 @@ static int meson_dw_hdmi_bind(struct device *dev, struct device *master,
 
 	platform_set_drvdata(pdev, meson_dw_hdmi);
 
-	meson_dw_hdmi->hdmi = dw_hdmi_bind(pdev, encoder,
-					   &meson_dw_hdmi->dw_plat_data);
+	meson_dw_hdmi->hdmi = dw_hdmi_probe(pdev,
+					    &meson_dw_hdmi->dw_plat_data);
 	if (IS_ERR(meson_dw_hdmi->hdmi))
 		return PTR_ERR(meson_dw_hdmi->hdmi);
 
+	next_bridge = of_drm_find_bridge(pdev->dev.of_node);
+	if (next_bridge)
+		drm_bridge_attach(encoder, next_bridge,
+				  &meson_dw_hdmi->bridge, 0);
+
 	DRM_DEBUG_DRIVER("HDMI controller initialized\n");
 
 	return 0;
Signature · 1 line
2.22.0
#8 lore raw

PATCH v5 8/11 drm/meson: dw-hdmi: stop enforcing input_bus_format

In reply to Neil Armstrong

To allow using formats from negotiation, stop enforcing input_bus_format in the private dw-plat-data struct.

---
 drivers/gpu/drm/meson/meson_dw_hdmi.c | 1 -
 1 file changed, 1 deletion(-)
drivers/gpu/drm/meson/meson_dw_hdmi.c +0 -1
index 8f51d032262c..72c118142eaf 100644
@@ -1014,7 +1014,6 @@ static int meson_dw_hdmi_bind(struct device *dev, struct device *master,
 	dw_plat_data->phy_ops = &meson_dw_hdmi_phy_ops;
 	dw_plat_data->phy_name = "meson_dw_hdmi_phy";
 	dw_plat_data->phy_data = meson_dw_hdmi;
-	dw_plat_data->input_bus_format = MEDIA_BUS_FMT_YUV8_1X24;
 	dw_plat_data->input_bus_encoding = V4L2_YCBCR_ENC_709;
 
 	if (dw_hdmi_is_compatible(meson_dw_hdmi, "amlogic,meson-gxl-dw-hdmi") ||
Signature · 6 lines
2.22.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#9 lore raw

PATCH v5 9/11 drm/meson: venc: add support for YUV420 setup

In reply to Neil Armstrong

This patch adds encoding support for the YUV420 output from the Amlogic Meson SoCs Video Processing Unit to the HDMI Controller.

The YUV420 is obtained by generating a YUV444 pixel stream like the classic HDMI display modes, but then the Video Encoder output can be configured to down-sample the YUV444 pixel stream to a YUV420 stream.

In addition if pixel stream down-sampling, the Y Cb Cr components must also be mapped differently to align with the HDMI2.0 specifications.

---
 drivers/gpu/drm/meson/meson_dw_hdmi.c | 3 ++-
 drivers/gpu/drm/meson/meson_venc.c    | 8 +++++---
 drivers/gpu/drm/meson/meson_venc.h    | 2 ++
 3 files changed, 9 insertions(+), 4 deletions(-)
drivers/gpu/drm/meson/meson_dw_hdmi.c +2 -1
index 72c118142eaf..b2105c0fe205 100644
@@ -752,7 +752,8 @@ static void meson_venc_hdmi_encoder_mode_set(struct drm_bridge *bridge,
 	DRM_DEBUG_DRIVER("\"%s\" vic %d\n", mode->name, vic);
 
 	/* VENC + VENC-DVI Mode setup */
-	meson_venc_hdmi_mode_set(priv, vic, mode);
+	meson_venc_hdmi_mode_set(priv, vic, ycrcb_map, false,
+				 VPU_HDMI_OUTPUT_CBYCR);
 
 	/* VCLK Set clock */
 	dw_hdmi_set_vclk(dw_hdmi, mode);
drivers/gpu/drm/meson/meson_venc.c +5 -3
index a9ab78970bfe..f93c725b6f02 100644
@@ -946,6 +946,8 @@ bool meson_venc_hdmi_venc_repeat(int vic)
 EXPORT_SYMBOL_GPL(meson_venc_hdmi_venc_repeat);
 
 void meson_venc_hdmi_mode_set(struct meson_drm *priv, int vic,
+			      unsigned int ycrcb_map,
+			      bool yuv420_mode,
 			      const struct drm_display_mode *mode)
 {
 	union meson_hdmi_venc_mode *vmode = NULL;
@@ -1528,14 +1530,14 @@ void meson_venc_hdmi_mode_set(struct meson_drm *priv, int vic,
 	if (mode->flags & DRM_MODE_FLAG_PVSYNC)
 		reg |= VPU_HDMI_INV_VSYNC;
 
-	/* Output data format: CbYCr */
-	reg |= VPU_HDMI_OUTPUT_CBYCR;
+	/* Output data format */
+	reg |= ycrcb_map;
 
 	/*
 	 * Write rate to the async FIFO between VENC and HDMI.
 	 * One write every 2 wr_clk.
 	 */
-	if (venc_repeat)
+	if (venc_repeat || yuv420_mode)
 		reg |= VPU_HDMI_WR_RATE(2);
 
 	/*
drivers/gpu/drm/meson/meson_venc.h +2 -0
index 1abdcbdf51c0..9138255ffc9e 100644
@@ -60,6 +60,8 @@ extern struct meson_cvbs_enci_mode meson_cvbs_enci_ntsc;
 void meson_venci_cvbs_mode_set(struct meson_drm *priv,
 			       struct meson_cvbs_enci_mode *mode);
 void meson_venc_hdmi_mode_set(struct meson_drm *priv, int vic,
+			      unsigned int ycrcb_map,
+			      bool yuv420_mode,
 			      const struct drm_display_mode *mode);
 unsigned int meson_venci_get_field(struct meson_drm *priv);
 
Signature · 1 line
2.22.0
#10 lore raw

PATCH v5 10/11 drm/meson: vclk: add support for YUV420 setup

In reply to Neil Armstrong

This patch adds clocking support for the YUV420 output from the Amlogic Meson SoCs Video Processing Unit to the HDMI Controller.

The YUV420 is obtained by generating a YUV444 pixel stream like the classic HDMI display modes, but then the Video Encoder output can be configured to down-sample the YUV444 pixel stream to a YUV420 stream.

This mode needs a different clock generation scheme since the TMDS PHY clock must match the 10x ratio with the YUV420 pixel clock, but the video encoder must run at 2x the pixel clock.

This patch adds the TMDS PHY clock value in all the video clock setup in order to better support these specific uses cases and switch to the Common Clock framework for clocks handling in the future.

---
 drivers/gpu/drm/meson/meson_dw_hdmi.c   | 24 ++++---
 drivers/gpu/drm/meson/meson_vclk.c      | 93 +++++++++++++++++++------
 drivers/gpu/drm/meson/meson_vclk.h      |  7 +-
 drivers/gpu/drm/meson/meson_venc_cvbs.c |  6 +-
 4 files changed, 95 insertions(+), 35 deletions(-)
drivers/gpu/drm/meson/meson_dw_hdmi.c +16 -8
index b2105c0fe205..b5b0d45eb314 100644
@@ -376,15 +376,19 @@ static void dw_hdmi_set_vclk(struct meson_dw_hdmi *dw_hdmi,
 {
 	struct meson_drm *priv = dw_hdmi->priv;
 	int vic = drm_match_cea_mode(mode);
+	unsigned int phy_freq;
 	unsigned int vclk_freq;
 	unsigned int venc_freq;
 	unsigned int hdmi_freq;
 
 	vclk_freq = mode->clock;
 
+	/* TMDS clock is pixel_clock * 10 */
+	phy_freq = vclk_freq * 10;
+
 	if (!vic) {
-		meson_vclk_setup(priv, MESON_VCLK_TARGET_DMT, vclk_freq,
-				 vclk_freq, vclk_freq, false);
+		meson_vclk_setup(priv, MESON_VCLK_TARGET_DMT, phy_freq,
+				 vclk_freq, vclk_freq, vclk_freq, false);
 		return;
 	}
 
@@ -402,11 +406,11 @@ static void dw_hdmi_set_vclk(struct meson_dw_hdmi *dw_hdmi,
 	if (mode->flags & DRM_MODE_FLAG_DBLCLK)
 		venc_freq /= 2;
 
-	DRM_DEBUG_DRIVER("vclk:%d venc=%d hdmi=%d enci=%d\n",
-		vclk_freq, venc_freq, hdmi_freq,
+	DRM_DEBUG_DRIVER("vclk:%d phy=%d venc=%d hdmi=%d enci=%d\n",
+		phy_freq, vclk_freq, venc_freq, hdmi_freq,
 		priv->venc.hdmi_use_enci);
 
-	meson_vclk_setup(priv, MESON_VCLK_TARGET_HDMI, vclk_freq,
+	meson_vclk_setup(priv, MESON_VCLK_TARGET_HDMI, phy_freq, vclk_freq,
 			 venc_freq, hdmi_freq, priv->venc.hdmi_use_enci);
 }
 
@@ -617,6 +621,7 @@ dw_hdmi_mode_valid(struct drm_connector *connector,
 		   const struct drm_display_mode *mode)
 {
 	struct meson_drm *priv = connector->dev->dev_private;
+	unsigned int phy_freq;
 	unsigned int vclk_freq;
 	unsigned int venc_freq;
 	unsigned int hdmi_freq;
@@ -643,6 +648,9 @@ dw_hdmi_mode_valid(struct drm_connector *connector,
 
 	vclk_freq = mode->clock;
 
+	/* TMDS clock is pixel_clock * 10 */
+	phy_freq = vclk_freq * 10;
+
 	/* 480i/576i needs global pixel doubling */
 	if (mode->flags & DRM_MODE_FLAG_DBLCLK)
 		vclk_freq *= 2;
@@ -659,10 +667,10 @@ dw_hdmi_mode_valid(struct drm_connector *connector,
 	if (mode->flags & DRM_MODE_FLAG_DBLCLK)
 		venc_freq /= 2;
 
-	dev_dbg(connector->dev->dev, "%s: vclk:%d venc=%d hdmi=%d\n", __func__,
-		vclk_freq, venc_freq, hdmi_freq);
+	dev_dbg(connector->dev->dev, "%s: vclk:%d phy=%d venc=%d hdmi=%d\n",
+		__func__, phy_freq, vclk_freq, venc_freq, hdmi_freq);
 
-	return meson_vclk_vic_supported_freq(vclk_freq);
+	return meson_vclk_vic_supported_freq(phy_freq, vclk_freq);
 }
 
 /* Encoder */
drivers/gpu/drm/meson/meson_vclk.c +71 -22

203 lines not on this page · raw message

drivers/gpu/drm/meson/meson_vclk.h +4 -3
index b62125540aef..aed0ab2efa71 100644
@@ -25,10 +25,11 @@ enum {
 enum drm_mode_status
 meson_vclk_dmt_supported_freq(struct meson_drm *priv, unsigned int freq);
 enum drm_mode_status
-meson_vclk_vic_supported_freq(unsigned int freq);
+meson_vclk_vic_supported_freq(unsigned int phy_freq, unsigned int vclk_freq);
 
 void meson_vclk_setup(struct meson_drm *priv, unsigned int target,
-		      unsigned int vclk_freq, unsigned int venc_freq,
-		      unsigned int dac_freq, bool hdmi_use_enci);
+		      unsigned int phy_freq, unsigned int vclk_freq,
+		      unsigned int venc_freq, unsigned int dac_freq,
+		      bool hdmi_use_enci);
 
 #endif /* __MESON_VCLK_H */
drivers/gpu/drm/meson/meson_venc_cvbs.c +4 -2
index 1bd6b6d15ffb..541f9eb2a135 100644
@@ -213,8 +213,10 @@ static void meson_venc_cvbs_encoder_mode_set(struct drm_encoder *encoder,
 		meson_venci_cvbs_mode_set(priv, meson_mode->enci);
 
 		/* Setup 27MHz vclk2 for ENCI and VDAC */
-		meson_vclk_setup(priv, MESON_VCLK_TARGET_CVBS, MESON_VCLK_CVBS,
-				 MESON_VCLK_CVBS, MESON_VCLK_CVBS, true);
+		meson_vclk_setup(priv, MESON_VCLK_TARGET_CVBS,
+				 MESON_VCLK_CVBS, MESON_VCLK_CVBS,
+				 MESON_VCLK_CVBS, MESON_VCLK_CVBS,
+				 true);
 	}
 }
 
Signature · 1 line
2.22.0
#11 lore raw

PATCH v5 11/11 drm/meson: Add YUV420 output support

In reply to Neil Armstrong

This patch adds support for the YUV420 output from the Amlogic Meson SoCs Video Processing Unit to the HDMI Controller.

The YUV420 is obtained by generating a YUV444 pixel stream like the classic HDMI display modes, but then the Video Encoder output can be configured to down-sample the YUV444 pixel stream to a YUV420 stream.
In addition if pixel stream down-sampling, the Y Cb Cr components must also be mapped differently to align with the HDMI2.0 specifications.

This mode needs a different clock generation scheme since the TMDS PHY clock must match the 10x ratio with the YUV420 pixel clock, but the video encoder must run at 2x the pixel clock.

This patch enables the bridge bus format negociation, and handles the YUV420 case if selected by the negociation.

---
 drivers/gpu/drm/meson/meson_dw_hdmi.c | 91 ++++++++++++++++++++-------
 1 file changed, 70 insertions(+), 21 deletions(-)
drivers/gpu/drm/meson/meson_dw_hdmi.c +70 -21
index b5b0d45eb314..e8c94915a4fc 100644
@@ -150,6 +150,7 @@ struct meson_dw_hdmi {
 	struct regulator *hdmi_supply;
 	u32 irq_stat;
 	struct dw_hdmi *hdmi;
+	unsigned long output_bus_fmt;
 };
 #define encoder_to_meson_dw_hdmi(x) \
 	container_of(x, struct meson_dw_hdmi, encoder)
@@ -301,6 +302,10 @@ static void meson_hdmi_phy_setup_mode(struct meson_dw_hdmi *dw_hdmi,
 	struct meson_drm *priv = dw_hdmi->priv;
 	unsigned int pixel_clock = mode->clock;
 
+	/* For 420, pixel clock is half unlike venc clock */
+	if (dw_hdmi->output_bus_fmt == MEDIA_BUS_FMT_UYYVYY8_0_5X24)
+		pixel_clock /= 2;
+
 	if (dw_hdmi_is_compatible(dw_hdmi, "amlogic,meson-gxl-dw-hdmi") ||
 	    dw_hdmi_is_compatible(dw_hdmi, "amlogic,meson-gxm-dw-hdmi")) {
 		if (pixel_clock >= 371250) {
@@ -383,6 +388,10 @@ static void dw_hdmi_set_vclk(struct meson_dw_hdmi *dw_hdmi,
 
 	vclk_freq = mode->clock;
 
+	/* For 420, pixel clock is half unlike venc clock */
+	if (dw_hdmi->output_bus_fmt == MEDIA_BUS_FMT_UYYVYY8_0_5X24)
+		vclk_freq /= 2;
+
 	/* TMDS clock is pixel_clock * 10 */
 	phy_freq = vclk_freq * 10;
 
@@ -392,13 +401,16 @@ static void dw_hdmi_set_vclk(struct meson_dw_hdmi *dw_hdmi,
 		return;
 	}
 
+	/* 480i/576i needs global pixel doubling */
 	if (mode->flags & DRM_MODE_FLAG_DBLCLK)
 		vclk_freq *= 2;
 
 	venc_freq = vclk_freq;
 	hdmi_freq = vclk_freq;
 
-	if (meson_venc_hdmi_venc_repeat(vic))
+	/* VENC double pixels for 1080i, 720p and YUV420 modes */
+	if (meson_venc_hdmi_venc_repeat(vic) ||
+	    dw_hdmi->output_bus_fmt == MEDIA_BUS_FMT_UYYVYY8_0_5X24)
 		venc_freq *= 2;
 
 	vclk_freq = max(venc_freq, hdmi_freq);
@@ -445,8 +457,9 @@ static int dw_hdmi_phy_init(struct dw_hdmi *hdmi, void *data,
 	/* Enable normal output to PHY */
 	dw_hdmi->data->top_write(dw_hdmi, HDMITX_TOP_BIST_CNTL, BIT(12));
 
-	/* TMDS pattern setup (TOFIX Handle the YUV420 case) */
-	if (mode->clock > 340000) {
+	/* TMDS pattern setup */
+	if (mode->clock > 340000 &&
+	    dw_hdmi->output_bus_fmt == MEDIA_BUS_FMT_YUV8_1X24) {
 		dw_hdmi->data->top_write(dw_hdmi, HDMITX_TOP_TMDS_CLK_PTTN_01,
 				  0);
 		dw_hdmi->data->top_write(dw_hdmi, HDMITX_TOP_TMDS_CLK_PTTN_23,
@@ -621,6 +634,7 @@ dw_hdmi_mode_valid(struct drm_connector *connector,
 		   const struct drm_display_mode *mode)
 {
 	struct meson_drm *priv = connector->dev->dev_private;
+	bool is_hdmi2_sink = connector->display_info.hdmi.scdc.supported;
 	unsigned int phy_freq;
 	unsigned int vclk_freq;
 	unsigned int venc_freq;
@@ -630,9 +644,11 @@ dw_hdmi_mode_valid(struct drm_connector *connector,
 
 	DRM_DEBUG_DRIVER("Modeline " DRM_MODE_FMT "\n", DRM_MODE_ARG(mode));
 
-	/* If sink max TMDS clock, we reject the mode */
+	/* If sink does not support 540MHz, reject the non-420 HDMI2 modes */
 	if (connector->display_info.max_tmds_clock &&
-	    mode->clock > connector->display_info.max_tmds_clock)
+	    mode->clock > connector->display_info.max_tmds_clock &&
+	    !drm_mode_is_420_only(&connector->display_info, mode) &&
+	    !drm_mode_is_420_also(&connector->display_info, mode))
 		return MODE_BAD;
 
 	/* Check against non-VIC supported modes */
@@ -648,6 +664,12 @@ dw_hdmi_mode_valid(struct drm_connector *connector,
 
 	vclk_freq = mode->clock;
 
+	/* For 420, pixel clock is half unlike venc clock */
+	if (drm_mode_is_420_only(&connector->display_info, mode) ||
+	    (!is_hdmi2_sink &&
+	     drm_mode_is_420_also(&connector->display_info, mode)))
+		vclk_freq /= 2;
+
 	/* TMDS clock is pixel_clock * 10 */
 	phy_freq = vclk_freq * 10;
 
@@ -658,8 +680,11 @@ dw_hdmi_mode_valid(struct drm_connector *connector,
 	venc_freq = vclk_freq;
 	hdmi_freq = vclk_freq;
 
-	/* VENC double pixels for 1080i and 720p modes */
-	if (meson_venc_hdmi_venc_repeat(vic))
+	/* VENC double pixels for 1080i, 720p and YUV420 modes */
+	if (meson_venc_hdmi_venc_repeat(vic) ||
+	    drm_mode_is_420_only(&connector->display_info, mode) ||
+	    (!is_hdmi2_sink &&
+	     drm_mode_is_420_also(&connector->display_info, mode)))
 		venc_freq *= 2;
 
 	vclk_freq = max(venc_freq, hdmi_freq);
@@ -677,6 +702,7 @@ dw_hdmi_mode_valid(struct drm_connector *connector,
 
 static const u32 meson_dw_hdmi_out_bus_fmts[] = {
 	MEDIA_BUS_FMT_YUV8_1X24,
+	MEDIA_BUS_FMT_UYYVYY8_0_5X24,
 };
 
 static void meson_venc_hdmi_encoder_destroy(struct drm_encoder *encoder)
@@ -697,18 +723,23 @@ meson_venc_hdmi_encoder_get_inp_bus_fmts(struct drm_bridge *bridge,
 					unsigned int *num_input_fmts)
 {
 	u32 *input_fmts = NULL;
+	int i;
 
-	if (output_fmt == meson_dw_hdmi_out_bus_fmts[0]) {
-		*num_input_fmts = 1;
-		input_fmts = kcalloc(*num_input_fmts,
-				     sizeof(*input_fmts),
-				     GFP_KERNEL);
-		if (!input_fmts)
-			return NULL;
+	*num_input_fmts = 0;
 
-		input_fmts[0] = output_fmt;
-	} else {
-		*num_input_fmts = 0;
+	for (i = 0 ; i < ARRAY_SIZE(meson_dw_hdmi_out_bus_fmts) ; ++i) {
+		if (output_fmt == meson_dw_hdmi_out_bus_fmts[i]) {
+			*num_input_fmts = 1;
+			input_fmts = kcalloc(*num_input_fmts,
+					     sizeof(*input_fmts),
+					     GFP_KERNEL);
+			if (!input_fmts)
+				return NULL;
+
+			input_fmts[0] = output_fmt;
+
+			break;
+		}
 	}
 
 	return input_fmts;
@@ -719,6 +750,12 @@ static int meson_venc_hdmi_encoder_atomic_check(struct drm_bridge *bridge,
 					struct drm_crtc_state *crtc_state,
 					struct drm_connector_state *conn_state)
 {
+	struct meson_dw_hdmi *dw_hdmi = bridge_to_meson_dw_hdmi(bridge);
+
+	dw_hdmi->output_bus_fmt = bridge_state->output_bus_cfg.format;
+
+	DRM_DEBUG_DRIVER("output_bus_fmt %lx\n", dw_hdmi->output_bus_fmt);
+
 	return 0;
 }
 
@@ -756,18 +793,29 @@ static void meson_venc_hdmi_encoder_mode_set(struct drm_bridge *bridge,
 	struct meson_dw_hdmi *dw_hdmi = bridge_to_meson_dw_hdmi(bridge);
 	struct meson_drm *priv = dw_hdmi->priv;
 	int vic = drm_match_cea_mode(mode);
+	unsigned int ycrcb_map = VPU_HDMI_OUTPUT_CBYCR;
+	bool yuv420_mode = false;
 
 	DRM_DEBUG_DRIVER("\"%s\" vic %d\n", mode->name, vic);
 
+	if (dw_hdmi->output_bus_fmt == MEDIA_BUS_FMT_UYYVYY8_0_5X24) {
+		ycrcb_map = VPU_HDMI_OUTPUT_CRYCB;
+		yuv420_mode = true;
+	}
+
 	/* VENC + VENC-DVI Mode setup */
-	meson_venc_hdmi_mode_set(priv, vic, ycrcb_map, false,
-				 VPU_HDMI_OUTPUT_CBYCR);
+	meson_venc_hdmi_mode_set(priv, vic, ycrcb_map, yuv420_mode, mode);
 
 	/* VCLK Set clock */
 	dw_hdmi_set_vclk(dw_hdmi, mode);
 
-	/* Setup YUV444 to HDMI-TX, no 10bit diphering */
-	writel_relaxed(0, priv->io_base + _REG(VPU_HDMI_FMT_CTRL));
+	if (dw_hdmi->output_bus_fmt == MEDIA_BUS_FMT_UYYVYY8_0_5X24)
+		/* Setup YUV420 to HDMI-TX, no 10bit diphering */
+		writel_relaxed(2 | (2 << 2),
+			       priv->io_base + _REG(VPU_HDMI_FMT_CTRL));
+	else
+		/* Setup YUV444 to HDMI-TX, no 10bit diphering */
+		writel_relaxed(0, priv->io_base + _REG(VPU_HDMI_FMT_CTRL));
 }
 
 static const struct drm_bridge_funcs meson_venc_hdmi_encoder_bridge_funcs = {
@@ -1024,6 +1072,7 @@ static int meson_dw_hdmi_bind(struct device *dev, struct device *master,
 	dw_plat_data->phy_name = "meson_dw_hdmi_phy";
 	dw_plat_data->phy_data = meson_dw_hdmi;
 	dw_plat_data->input_bus_encoding = V4L2_YCBCR_ENC_709;
+	dw_plat_data->ycbcr_420_allowed = true;
 
 	if (dw_hdmi_is_compatible(meson_dw_hdmi, "amlogic,meson-gxl-dw-hdmi") ||
 	    dw_hdmi_is_compatible(meson_dw_hdmi, "amlogic,meson-gxm-dw-hdmi") ||
Signature · 1 line
2.22.0
author Applied
#12 lore raw
In reply to Neil Armstrong
Quoted 71 lines · Neil Armstrong

Hi Philippe, Heiko, Maxime, Laurent,

A bad negociation was detected on platforms not implementing a bridge on the encoder side, which has been fixed in this version.

Could you check it doesn't break your platforms using dw-hdmi ? Especially patches 1-5.

Thanks,
Neil

This patchset is based on Boris's merged "drm: Add support for bus-format negotiation" patchset to implement full bus-format negotiation for DW-HDMI, including YUV420 support and 10/12/16bit YUV444, YUV422 and RGB. The Color Space Converter support is already implemented.

And the counterpart implementation in the Amlogic Meson VPU dw-hdmi glue :
- basic bus-format negotiation to select YUV444 bus-format as DW-HDMI input
- YUV420 support when HDMI2.0 YUV420 modeset

This is a follow-up from the previous attempts :
- "drm/meson: Add support for HDMI2.0 YUV420 4k60" at [2]
- "drm/meson: Add support for HDMI2.0 4k60" at [3]

Changes since v4 at [7]:
- Cleaned up patch 1
- Added comment on patch 2
- Added commit message on patch 3
- Fixed invalid negociation when encoder is not yet a bridge (seen on allwinner & rockchip platforms) on patch 4
- Fixed invalid defines, handled MEDIA_BUS_FMT_FIXED and cleaned negociation debug on patch 4
- Added tags on patch 5, 6
- Removed meson_venc_hdmi_encoder_get_out_bus_fmts on patch 7
- Add off-list r-b from Jernej

Changes since v3 at [6]:
- Added "Plug atomic state hooks to the default implementation" on drm/bridge: dw-hdmi
- Also added these atomic state hooks in meson-dw-hdmi in patch 7
- Rebased on latest drm-misc-next including patches 1-7 of [1]

Changes since RFC v2 at [5]:
- Added fixes from Jonas, who tested and integrated it for Rockchip SoCs
- Added support for 10/12/16bit tmds clock calculation
- Added support for max_bcp connector property
- Adapted to Boris's v4 patchset
- Fixed typos reported by boris

Changes since RFC v1 at [4]:
- Rewrote negociation using the v2 patchset, including full DW-HDMI fmt negociation

[2] https://patchwork.freedesktop.org/patch/msgid/[email protected]
[3] https://patchwork.freedesktop.org/patch/msgid/[email protected]
[4] https://patchwork.freedesktop.org/patch/msgid/[email protected]
[5] https://patchwork.freedesktop.org/patch/msgid/[email protected]
[6] https://patchwork.freedesktop.org/patch/msgid/[email protected]
[7] https://patchwork.freedesktop.org/patch/msgid/[email protected]

Jonas Karlman (2):
drm/bridge: dw-hdmi: set mtmdsclock for deep color drm/bridge: dw-hdmi: add max bpc connector property

Neil Armstrong (9):
drm/bridge: dw-hdmi: Plug atomic state hooks to the default
implementation
drm/bridge: synopsys: dw-hdmi: add bus format negociation drm/bridge: synopsys: dw-hdmi: allow ycbcr420 modes for >= 0x200a drm/meson: venc: make drm_display_mode const
drm/meson: meson_dw_hdmi: add bridge and switch to drm_bridge_funcs drm/meson: dw-hdmi: stop enforcing input_bus_format drm/meson: venc: add support for YUV420 setup
drm/meson: vclk: add support for YUV420 setup
drm/meson: Add YUV420 output support

Quoted 10 lines
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 319 +++++++++++++++++++++-
 drivers/gpu/drm/meson/meson_dw_hdmi.c     | 180 +++++++++---
 drivers/gpu/drm/meson/meson_vclk.c        |  93 +++++--
 drivers/gpu/drm/meson/meson_vclk.h        |   7 +-
 drivers/gpu/drm/meson/meson_venc.c        |  10 +-
 drivers/gpu/drm/meson/meson_venc.h        |   4 +-
 drivers/gpu/drm/meson/meson_venc_cvbs.c   |   6 +-
 include/drm/bridge/dw_hdmi.h              |   1 +
 8 files changed, 544 insertions(+), 76 deletions(-)

Pushed to drm-misc-next

Neil
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

#13 lore raw
In reply to Neil Armstrong
This series was applied to khilman/linux-amlogic.git (refs/heads/for-next).

Hello:

This series was applied to khilman/linux-amlogic.git (refs/heads/for-next).

Quoted 9 lines · On Wed, 4 Mar 2020 11:40:41 +0100 you wrote:

Hi Philippe, Heiko, Maxime, Laurent,

A bad negociation was detected on platforms not implementing a bridge on the encoder side, which has been fixed in this version.

Could you check it doesn't break your platforms using dw-hdmi ? Especially patches 1-5.

[...]

Here is a summary with links:
- [v5,01/11] drm/bridge: dw-hdmi: set mtmdsclock for deep color

    https://git.kernel.org/khilman/linux-amlogic/c/c6cae702340069d9f48925bd2201359602a72e83
  - [v5,02/11] drm/bridge: dw-hdmi: add max bpc connector property
    https://git.kernel.org/khilman/linux-amlogic/c/b8e810e868f73a698af9bde1ac51a332c0f61fc4
  - [v5,03/11] drm/bridge: dw-hdmi: Plug atomic state hooks to the default implementation
    https://git.kernel.org/khilman/linux-amlogic/c/a5cf9e2e52b638ae62049bf06d2283f5d757ac7d
  - [v5,04/11] drm/bridge: synopsys: dw-hdmi: add bus format negociation
    https://git.kernel.org/khilman/linux-amlogic/c/6c3c719936dafeb5df3a625cd57a674bf1d6ef31
  - [v5,05/11] drm/bridge: synopsys: dw-hdmi: allow ycbcr420 modes for >= 0x200a
    https://git.kernel.org/khilman/linux-amlogic/c/f14d3f6c39f39acf0eec90f4dcf1105f7be1fc1b
  - [v5,06/11] drm/meson: venc: make drm_display_mode const
    https://git.kernel.org/khilman/linux-amlogic/c/0fad640bbfed33e7e2a8db056e3782b396c42185
  - [v5,07/11] drm/meson: meson_dw_hdmi: add bridge and switch to drm_bridge_funcs
    https://git.kernel.org/khilman/linux-amlogic/c/f43aa58432de8fba8975826eedbd51425b791688
  - [v5,08/11] drm/meson: dw-hdmi: stop enforcing input_bus_format
    https://git.kernel.org/khilman/linux-amlogic/c/1fd34184aab0fe04c5d50af01a37fe1bb8bd6595
  - [v5,09/11] drm/meson: venc: add support for YUV420 setup
    https://git.kernel.org/khilman/linux-amlogic/c/64db601a9561778b41add87270daf512c9bf0433
  - [v5,10/11] drm/meson: vclk: add support for YUV420 setup
    https://git.kernel.org/khilman/linux-amlogic/c/e5fab2ec9ca4f7db47aaf1d7f39e43a13b03a4b7
  - [v5,11/11] drm/meson: Add YUV420 output support
    https://git.kernel.org/khilman/linux-amlogic/c/8496a2172d7cd25d1baa734b756cbee4574d4652

You are awesome, thank you!

Signature · 7 lines
Deet-doot-dot, I am a bot.
https://korg.wiki.kernel.org/userdoc/pwbot

_______________________________________________
linux-amlogic mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-amlogic