Skip to contentSkip to conversation

ARM: dts: stm32: Split AV96 into DHCOR SoM and AV96 board

PATCH New Marek Vasut 2 participants 3 messages Mar 26, 2020 – Mar 30, 2020

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ARM: dts: stm32: Split AV96 into DHCOR SoM and AV96 board

The AV96 is in fact an assembly of DH Electronics DHCOR SoM on top of an AV96 reference board. Split the DTs to reflect that and make sure to DHCOR SoM can be reused on other boards easily.

It is also highly recommended to configure the board for the DHCOM make stm32mp15_dhcom_basic_defconfig
make DEVICE_TREE=stm32mp15xx-dhcor-avenger96
as that permits reusing the board code for the DH components, like accessing and reading out the ethernet MAC from EEPROM.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>
---
 arch/arm/dts/Makefile                         |   3 +-
 arch/arm/dts/stm32mp157a-avenger96.dts        | 393 +-----------------
 .../stm32mp15xx-dhcor-avenger96-u-boot.dtsi   |  80 ++++
 arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts  | 196 +++++++++
 ...oot.dtsi => stm32mp15xx-dhcor-u-boot.dtsi} |  79 +---
 arch/arm/dts/stm32mp15xx-dhcor.dtsi           | 220 ++++++++++
 doc/board/st/stm32mp1.rst                     |   8 +-
 7 files changed, 509 insertions(+), 470 deletions(-)
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts
 rename arch/arm/dts/{stm32mp157a-avenger96-u-boot.dtsi => stm32mp15xx-dhcor-u-boot.dtsi} (75%)
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcor.dtsi
arch/arm/dts/Makefile +2 -1
index 9c593b2c98..2564f790de 100644
@@ -884,7 +884,8 @@ dtb-$(CONFIG_STM32MP15x) += \
 	stm32mp157c-dk2.dtb \
 	stm32mp157c-ed1.dtb \
 	stm32mp157c-ev1.dtb \
-	stm32mp15xx-dhcom-pdk2.dtb
+	stm32mp15xx-dhcom-pdk2.dtb \
+	stm32mp15xx-dhcor-avenger96.dtb
 
 dtb-$(CONFIG_SOC_K3_AM6) += k3-am654-base-board.dtb k3-am654-r5-base-board.dtb
 dtb-$(CONFIG_SOC_K3_J721E) += k3-j721e-common-proc-board.dtb \
arch/arm/dts/stm32mp157a-avenger96.dts +2 -391

396 lines not on this page · raw message

arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi new file +80 -0

80 lines not on this page · raw message

arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts new file +196 -0

196 lines not on this page · raw message

arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi renamed from arch/arm/dts/stm32mp157a-avenger96-u-boot.dtsi +5 -74

103 lines not on this page · raw message

arch/arm/dts/stm32mp15xx-dhcor.dtsi new file +220 -0

220 lines not on this page · raw message

doc/board/st/stm32mp1.rst +4 -4
index 1640bf910e..73195134f1 100644
@@ -43,11 +43,11 @@ And the necessary drivers
 
 Currently the following boards are supported:
 
- + stm32mp157a-avenger96.dts
  + stm32mp157a-dk1.dts
  + stm32mp157c-dk2.dts
  + stm32mp157c-ed1.dts
  + stm32mp157c-ev1.dts
+ + stm32mp15xx-dhcor-avenger96.dts
 
 Boot Sequences
 --------------
@@ -145,9 +145,9 @@ the supported device trees for STM32MP15x are:
 
    + stm32mp157c-dk2
 
-+ avenger96: Avenger96 board from Arrow Electronics
++ avenger96: Avenger96 board from Arrow Electronics based on DH Elec. DHCOR SoM
 
-   + stm32mp157a-avenger96
+   + stm32mp15xx-dhcor-avenger96
 
 Build Procedure
 ---------------
@@ -229,7 +229,7 @@ Build Procedure
 
      # export KBUILD_OUTPUT=stm32mp15_basic
      # make stm32mp15_basic_defconfig
-     # make DEVICE_TREE=stm32mp157a-avenger96 all
+     # make DEVICE_TREE=stm32mp15xx-dhcor-avenger96 all
 
 6. Output files
 
Signature · 1 line
2.25.1
#1 lore raw

PATCH 1/1 ARM: dts: stm32: Split AV96 into DHCOR SoM and AV96 board

Hi Marek

Quoted 1,099 lines · Marek Vasut

The AV96 is in fact an assembly of DH Electronics DHCOR SoM on top of an AV96 reference board. Split the DTs to reflect that and make sure to DHCOR SoM can be reused on other boards easily.

It is also highly recommended to configure the board for the DHCOM make stm32mp15_dhcom_basic_defconfig
make DEVICE_TREE=stm32mp15xx-dhcor-avenger96
as that permits reusing the board code for the DH components, like accessing and reading out the ethernet MAC from EEPROM.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>
---
 arch/arm/dts/Makefile                         |   3 +-
 arch/arm/dts/stm32mp157a-avenger96.dts        | 393 +-----------------
 .../stm32mp15xx-dhcor-avenger96-u-boot.dtsi   |  80 ++++
 arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts  | 196 +++++++++
 ...oot.dtsi => stm32mp15xx-dhcor-u-boot.dtsi} |  79 +---
 arch/arm/dts/stm32mp15xx-dhcor.dtsi           | 220 ++++++++++
 doc/board/st/stm32mp1.rst                     |   8 +-
 7 files changed, 509 insertions(+), 470 deletions(-)
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts
 rename arch/arm/dts/{stm32mp157a-avenger96-u-boot.dtsi => stm32mp15xx-dhcor-u-boot.dtsi} (75%)
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcor.dtsi
arch/arm/dts/Makefile +2 -1
index 9c593b2c98..2564f790de 100644
@@ -884,7 +884,8 @@ dtb-$(CONFIG_STM32MP15x) += \
 	stm32mp157c-dk2.dtb \
 	stm32mp157c-ed1.dtb \
 	stm32mp157c-ev1.dtb \
-	stm32mp15xx-dhcom-pdk2.dtb
+	stm32mp15xx-dhcom-pdk2.dtb \
+	stm32mp15xx-dhcor-avenger96.dtb
 
 dtb-$(CONFIG_SOC_K3_AM6) += k3-am654-base-board.dtb k3-am654-r5-base-board.dtb
 dtb-$(CONFIG_SOC_K3_J721E) += k3-j721e-common-proc-board.dtb \
arch/arm/dts/stm32mp157a-avenger96.dts +2 -391
index 8e36df8787..9c165104fb 100644
@@ -4,394 +4,5 @@
  * Author: Manivannan Sadhasivam <[email protected]>
  */
 
-/dts-v1/;
-
-#include "stm32mp157c.dtsi"
-#include "stm32mp157xac-pinctrl.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/mfd/st,stpmic1.h>
-
-/ {
-	model = "Arrow Electronics STM32MP157A Avenger96 board";
-	compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157";
-
-	aliases {
-		ethernet0 = &ethernet0;
-		mmc0 = &sdmmc1;
-		serial0 = &uart4;
-		serial1 = &uart7;
-		spi0 = &qspi;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	memory at c0000000 {
-		device_type = "memory";
-		reg = <0xc0000000 0x40000000>;
-	};
-
-	led {
-		compatible = "gpio-leds";
-		led1 {
-			label = "green:user1";
-			gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-			default-state = "off";
-		};
-
-		led2 {
-			label = "green:user2";
-			gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc0";
-			default-state = "off";
-		};
-
-		led3 {
-			label = "green:user3";
-			gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc1";
-			default-state = "off";
-		};
-
-		led4 {
-			label = "green:user3";
-			gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "none";
-			default-state = "off";
-			panic-indicator;
-		};
-
-		led5 {
-			label = "yellow:wifi";
-			gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "phy0tx";
-			default-state = "off";
-		};
-
-		led6 {
-			label = "blue:bt";
-			gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "bluetooth-power";
-			default-state = "off";
-		};
-	};
-};
-
-&ethernet0 {
-	status = "okay";
-	pinctrl-0 = <&ethernet0_rgmii_pins_b>;
-	pinctrl-1 = <&ethernet0_rgmii_pins_sleep_b>;
-	pinctrl-names = "default", "sleep";
-	phy-mode = "rgmii";
-	max-speed = <1000>;
-	phy-handle = <&phy0>;
-	phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
-
-	mdio0 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "snps,dwmac-mdio";
-		phy0: ethernet-phy at 7 {
-			reg = <7>;
-		};
-	};
-};
-
-&i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_b>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/delete-property/dmas;
-	/delete-property/dma-names;
-};
-
-&i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_b1 &i2c2_pins_b2>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/delete-property/dmas;
-	/delete-property/dma-names;
-};
-
-&i2c4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c4_pins_a>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/delete-property/dmas;
-	/delete-property/dma-names;
-
-	pmic: stpmic at 33 {
-		compatible = "st,stpmic1";
-		reg = <0x33>;
-		interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		status = "okay";
-
-		st,main-control-register = <0x04>;
-		st,vin-control-register = <0xc0>;
-		st,usb-control-register = <0x30>;
-
-		regulators {
-			compatible = "st,stpmic1-regulators";
-
-			ldo1-supply = <&v3v3>;
-			ldo2-supply = <&v3v3>;
-			ldo3-supply = <&vdd_ddr>;
-			ldo5-supply = <&v3v3>;
-			ldo6-supply = <&v3v3>;
-			pwr_sw1-supply = <&bst_out>;
-			pwr_sw2-supply = <&bst_out>;
-
-			vddcore: buck1 {
-				regulator-name = "vddcore";
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <1350000>;
-				regulator-always-on;
-				regulator-initial-mode = <0>;
-				regulator-over-current-protection;
-			};
-
-			vdd_ddr: buck2 {
-				regulator-name = "vdd_ddr";
-				regulator-min-microvolt = <1350000>;
-				regulator-max-microvolt = <1350000>;
-				regulator-always-on;
-				regulator-initial-mode = <0>;
-				regulator-over-current-protection;
-			};
-
-			vdd: buck3 {
-				regulator-name = "vdd";
-				regulator-min-microvolt = <2500000>;
-				regulator-max-microvolt = <2500000>;
-				regulator-always-on;
-				st,mask_reset;
-				regulator-initial-mode = <0>;
-				regulator-over-current-protection;
-			};
-
-			v3v3: buck4 {
-				regulator-name = "v3v3";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-always-on;
-				regulator-over-current-protection;
-				regulator-initial-mode = <0>;
-			};
-
-			vdda: ldo1 {
-				regulator-name = "vdda";
-				regulator-min-microvolt = <2900000>;
-				regulator-max-microvolt = <2900000>;
-				interrupts = <IT_CURLIM_LDO1 0>;
-				interrupt-parent = <&pmic>;
-			};
-
-			v2v8: ldo2 {
-				regulator-name = "v2v8";
-				regulator-min-microvolt = <2800000>;
-				regulator-max-microvolt = <2800000>;
-				interrupts = <IT_CURLIM_LDO2 0>;
-				interrupt-parent = <&pmic>;
-			};
-
-			vtt_ddr: ldo3 {
-				regulator-name = "vtt_ddr";
-				regulator-min-microvolt = <0>;
-				regulator-max-microvolt = <1000000>;
-				regulator-always-on;
-				regulator-over-current-protection;
-			};
-
-			vdd_usb: ldo4 {
-				regulator-name = "vdd_usb";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-				interrupts = <IT_CURLIM_LDO4 0>;
-				interrupt-parent = <&pmic>;
-			};
-
-			vdd_sd: ldo5 {
-				regulator-name = "vdd_sd";
-				regulator-min-microvolt = <2900000>;
-				regulator-max-microvolt = <2900000>;
-				interrupts = <IT_CURLIM_LDO5 0>;
-				interrupt-parent = <&pmic>;
-				regulator-boot-on;
-			};
-
-			v1v8: ldo6 {
-				regulator-name = "v1v8";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				interrupts = <IT_CURLIM_LDO6 0>;
-				interrupt-parent = <&pmic>;
-				regulator-enable-ramp-delay = <300000>;
-			};
-
-			vref_ddr: vref_ddr {
-				regulator-name = "vref_ddr";
-				regulator-always-on;
-				regulator-over-current-protection;
-			};
-
-			bst_out: boost {
-				regulator-name = "bst_out";
-				interrupts = <IT_OCP_BOOST 0>;
-				interrupt-parent = <&pmic>;
-			};
-
-			vbus_otg: pwr_sw1 {
-				regulator-name = "vbus_otg";
-				interrupts = <IT_OCP_OTG 0>;
-				interrupt-parent = <&pmic>;
-				regulator-active-discharge = <1>;
-			};
-
-			vbus_sw: pwr_sw2 {
-				regulator-name = "vbus_sw";
-				interrupts = <IT_OCP_SWOUT 0>;
-				interrupt-parent = <&pmic>;
-				regulator-active-discharge = <1>;
-			};
-		};
-
-		onkey {
-			compatible = "st,stpmic1-onkey";
-			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
-			interrupt-names = "onkey-falling", "onkey-rising";
-			status = "okay";
-		};
-
-		watchdog {
-			compatible = "st,stpmic1-wdt";
-			status = "disabled";
-		};
-	};
-
-	eeprom at 53 {
-		compatible = "atmel,24c02";
-		reg = <0x53>;
-		pagesize = <16>;
-	};
-};
-
-&iwdg2 {
-	timeout-sec = <32>;
-	status = "okay";
-};
-
-&pwr_regulators {
-	vdd-supply = <&vdd>;
-	vdd_3v3_usbfs-supply = <&vdd_usb>;
-};
-
-&qspi {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
-	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
-	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
-	#address-cells = <1>;
-	#size-cells = <0>;
-	status = "okay";
-
-	flash0: mx66l51235l at 0 {
-		compatible = "jedec,spi-nor";
-		reg = <0>;
-		spi-rx-bus-width = <4>;
-		spi-max-frequency = <108000000>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-	};
-};
-
-&rng1 {
-	status = "okay";
-};
-
-&rtc {
-	status = "okay";
-};
-
-&sdmmc1 {
-	pinctrl-names = "default", "opendrain", "sleep";
-	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
-	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
-	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
-	broken-cd;
-	st,sig-dir;
-	st,neg-edge;
-	st,use-ckin;
-	bus-width = <4>;
-	vmmc-supply = <&vdd_sd>;
-	status = "okay";
-};
-
-&sdmmc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
-	non-removable;
-	no-sd;
-	no-sdio;
-	st,neg-edge;
-	bus-width = <8>;
-	vmmc-supply = <&v3v3>;
-	mmc-ddr-3_3v;
-	status = "okay";
-};
-
-&spi2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi2_pins_a>;
-	status = "okay";
-};
-
-&uart4 {
-	/* On Low speed expansion header */
-	label = "LS-UART1";
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart4_pins_b>;
-	status = "okay";
-};
-
-&uart7 {
-	/* On Low speed expansion header */
-	label = "LS-UART0";
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart7_pins_a>;
-	status = "okay";
-};
-
-&usbh_ehci {
-	phys = <&usbphyc_port0>;
-	phy-names = "usb";
-	status = "okay";
-};
-
-&usbotg_hs {
-	dr_mode = "peripheral";
-	phys = <&usbphyc_port1 0>;
-	phy-names = "usb2-phy";
-	status = "okay";
-};
-
-&usbphyc {
-	status = "okay";
-};
-
-&usbphyc_port0 {
-	phy-supply = <&vdd_usb>;
-};
-
-&usbphyc_port1 {
-	phy-supply = <&vdd_usb>;
-};
+/* This is kept for backward compatibility and will be removed */
+#include "stm32mp15xx-dhcor-avenger96.dts"
arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi new file +80 -0
new file mode 100644
index 0000000000..484f1436b8
@@ -0,0 +1,80 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marek Vasut <[email protected]>
+ */
+
+#include "stm32mp15xx-dhcor-u-boot.dtsi"
+
+/ {
+	aliases {
+		mmc0 = &sdmmc1;
+		mmc1 = &sdmmc2;
+		usb0 = &usbotg_hs;
+	};
+
+	config {
+		u-boot,boot-led = "led1";
+		u-boot,error-led = "led4";
+	};
+};
+
+&sdmmc1 {
+	u-boot,dm-spl;
+};
+
+&sdmmc1_b4_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc1_dir_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc2 {
+	u-boot,dm-spl;
+};
+
+&sdmmc2_b4_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc2_d47_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&uart4 {
+	u-boot,dm-pre-reloc;
+};
+
+&uart4_pins_b {
+	u-boot,dm-pre-reloc;
+	pins1 {
+		u-boot,dm-pre-reloc;
+	};
+	pins2 {
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&usbotg_hs {
+	u-boot,force-b-session-valid;
+	hnp-srp-disable;
+};
arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts new file +196 -0
new file mode 100644
index 0000000000..c912818ac9
@@ -0,0 +1,196 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <[email protected]>
+ * Copyright (C) 2020 Marek Vasut <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "stm32mp15xx-dhcor.dtsi"
+#include "stm32mp15xx-dhcor-avenger96-u-boot.dtsi"
+
+/ {
+	model = "Arrow Electronics STM32MP15xx Avenger96 board";
+	compatible = "arrow,stm32mp15xx-avenger96", "st,stm32mp15x";
+
+	aliases {
+		eeprom0 = &eeprom0;
+		ethernet0 = &ethernet0;
+		mmc0 = &sdmmc1;
+		serial0 = &uart4;
+		serial1 = &uart7;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	led {
+		compatible = "gpio-leds";
+		led1 {
+			label = "green:user1";
+			gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led2 {
+			label = "green:user2";
+			gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+
+		led3 {
+			label = "green:user3";
+			gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc1";
+			default-state = "off";
+		};
+
+		led4 {
+			label = "green:user3";
+			gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "none";
+			default-state = "off";
+			panic-indicator;
+		};
+
+		led5 {
+			label = "yellow:wifi";
+			gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy0tx";
+			default-state = "off";
+		};
+
+		led6 {
+			label = "blue:bt";
+			gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "bluetooth-power";
+			default-state = "off";
+		};
+	};
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_b>;
+	pinctrl-1 = <&ethernet0_rgmii_pins_sleep_b>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+	phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy at 7 {
+			reg = <7>;
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_b>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_b1 &i2c2_pins_b2>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c4 {
+	eeprom0: eeprom at 53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	broken-cd;
+	st,sig-dir;
+	st,neg-edge;
+	st,use-ckin;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	mmc-ddr-3_3v;
+	status = "okay";
+};
+
+&spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+};
+
+&uart4 {
+	/* On Low speed expansion header */
+	label = "LS-UART1";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_b>;
+	status = "okay";
+};
+
+&uart7 {
+	/* On Low speed expansion header */
+	label = "LS-UART0";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart7_pins_a>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi renamed from arch/arm/dts/stm32mp157a-avenger96-u-boot.dtsi +5 -74
similarity index 75%
rename from arch/arm/dts/stm32mp157a-avenger96-u-boot.dtsi
rename to arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi
index 8dcd8866e8..70b35e79e5 100644
@@ -4,25 +4,13 @@
  *
  * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
  * Author: Manivannan Sadhasivam <[email protected]>
+ * Copyright (C) 2020 Marek Vasut <[email protected]>
  */
 
 #include <dt-bindings/clock/stm32mp1-clksrc.h>
 #include "stm32mp157-u-boot.dtsi"
 #include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi"
 
-/ {
-	aliases {
-		mmc0 = &sdmmc1;
-		mmc1 = &sdmmc2;
-		usb0 = &usbotg_hs;
-	};
-
-	config {
-		u-boot,boot-led = "led1";
-		u-boot,error-led = "led4";
-	};
-};
-
 &i2c4 {
 	u-boot,dm-pre-reloc;
 };
@@ -38,6 +26,10 @@
 	u-boot,dm-pre-reloc;
 };
 
+&qspi {
+	u-boot,dm-spl;
+};
+
 &rcc {
 	st,clksrc = <
 		CLK_MPU_PLL1P
@@ -139,67 +131,6 @@
 	};
 };
 
-&sdmmc1 {
-	u-boot,dm-spl;
-};
-
-&sdmmc1_b4_pins_a {
-	u-boot,dm-spl;
-	pins {
-		u-boot,dm-spl;
-	};
-};
-
-&sdmmc1_dir_pins_a {
-	u-boot,dm-spl;
-	pins1 {
-		u-boot,dm-spl;
-	};
-	pins2 {
-		u-boot,dm-spl;
-	};
-};
-
-&sdmmc2 {
-	u-boot,dm-spl;
-};
-
-&sdmmc2_b4_pins_a {
-	u-boot,dm-spl;
-	pins1 {
-		u-boot,dm-spl;
-	};
-	pins2 {
-		u-boot,dm-spl;
-	};
-};
-
-&sdmmc2_d47_pins_a {
-	u-boot,dm-spl;
-	pins {
-		u-boot,dm-spl;
-	};
-};
-
-&uart4 {
-	u-boot,dm-pre-reloc;
-};
-
-&uart4_pins_b {
-	u-boot,dm-pre-reloc;
-	pins1 {
-		u-boot,dm-pre-reloc;
-	};
-	pins2 {
-		u-boot,dm-pre-reloc;
-	};
-};
-
-&usbotg_hs {
-	u-boot,force-b-session-valid;
-	hnp-srp-disable;
-};
-
 &v3v3 {
 	regulator-always-on;
 };
arch/arm/dts/stm32mp15xx-dhcor.dtsi new file +220 -0
new file mode 100644
index 0000000000..ff55505bfc
@@ -0,0 +1,220 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <[email protected]>
+ * Copyright (C) 2020 Marek Vasut <[email protected]>
+ */
+/dts-v1/;
+
+#include "stm32mp157c.dtsi"
+#include "stm32mp157xac-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	aliases {
+		spi0 = &qspi;
+	};
+
+	memory at c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x40000000>;
+	};
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pmic: stpmic at 33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		st,main-control-register = <0x04>;
+		st,vin-control-register = <0xc0>;
+		st,usb-control-register = <0x30>;
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+
+			ldo1-supply = <&v3v3>;
+			ldo2-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo5-supply = <&v3v3>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-always-on;
+				st,mask_reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			vdda: ldo1 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO1 0>;
+				interrupt-parent = <&pmic>;
+			};
+
+			v2v8: ldo2 {
+				regulator-name = "v2v8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				interrupts = <IT_CURLIM_LDO2 0>;
+				interrupt-parent = <&pmic>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <0>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				interrupts = <IT_CURLIM_LDO4 0>;
+				interrupt-parent = <&pmic>;
+			};
+
+			vdd_sd: ldo5 {
+				regulator-name = "vdd_sd";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				interrupt-parent = <&pmic>;
+				regulator-boot-on;
+			};
+
+			v1v8: ldo6 {
+				regulator-name = "v1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				interrupts = <IT_CURLIM_LDO6 0>;
+				interrupt-parent = <&pmic>;
+				regulator-enable-ramp-delay = <300000>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+				interrupt-parent = <&pmic>;
+			};
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+				interrupt-parent = <&pmic>;
+				regulator-active-discharge = <1>;
+			};
+
+			vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				interrupt-parent = <&pmic>;
+				regulator-active-discharge = <1>;
+			};
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash0: mx66l51235l at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
doc/board/st/stm32mp1.rst +3 -3
index 1640bf910e..73195134f1 100644
@@ -43,11 +43,11 @@ And the necessary drivers
 
 Currently the following boards are supported:
 
- + stm32mp157a-avenger96.dts
  + stm32mp157a-dk1.dts
  + stm32mp157c-dk2.dts
  + stm32mp157c-ed1.dts
  + stm32mp157c-ev1.dts
+ + stm32mp15xx-dhcor-avenger96.dts
 
 Boot Sequences
 --------------
@@ -145,9 +145,9 @@ the supported device trees for STM32MP15x are:
 
    + stm32mp157c-dk2
 
-+ avenger96: Avenger96 board from Arrow Electronics
++ avenger96: Avenger96 board from Arrow Electronics based on DH Elec. DHCOR SoM
 
-   + stm32mp157a-avenger96
+   + stm32mp15xx-dhcor-avenger96
 
 Build Procedure
 ---------------

doc/board/st/stm32mp1.rst Build Procedure · line 235

Quoted 8 lines
doc/board/st/stm32mp1.rst +1 -1
@@ -229,7 +229,7 @@ Build Procedure
 
      # export KBUILD_OUTPUT=stm32mp15_basic
      # make stm32mp15_basic_defconfig
-     # make DEVICE_TREE=stm32mp157a-avenger96 all
+     # make DEVICE_TREE=stm32mp15xx-dhcor-avenger96 all
 
 6. Output files
 

Thanks

#2 lore raw

PATCH 1/1 ARM: dts: stm32: Split AV96 into DHCOR SoM and AV96 board

Quoted 1 line · Patrice CHOTARD

Hi Marek

Hi,

[...]

Quoted 21 lines
Quoted 21 lines

Boot Sequences
--------------

doc/board/st/stm32mp1.rst +3 -3
@@ -145,9 +145,9 @@ the supported device trees for STM32MP15x are:
 
    + stm32mp157c-dk2
 
-+ avenger96: Avenger96 board from Arrow Electronics
++ avenger96: Avenger96 board from Arrow Electronics based on DH Elec. DHCOR SoM
 
-   + stm32mp157a-avenger96
+   + stm32mp15xx-dhcor-avenger96
 
 Build Procedure
 ---------------
@@ -229,7 +229,7 @@ Build Procedure
 
      # export KBUILD_OUTPUT=stm32mp15_basic
      # make stm32mp15_basic_defconfig
-     # make DEVICE_TREE=stm32mp157a-avenger96 all
+     # make DEVICE_TREE=stm32mp15xx-dhcor-avenger96 all
 
Quoted 6 lines

doc/board/st/stm32mp1.rst Build Procedure · line 235

Quoted 2 lines
doc/board/st/stm32mp1.rst +0 -0
 6. Output files
 

Thanks

It would be nice to get these AV96 fixes into 2020.04 release, because without all these, the board doesn't even boot :-( Do you have a branch with these patches applied, so I can check if something is missing ?

btw. please clip the email with [...], so it's easy to find the comments.