ARM: dts: stm32: Split AV96 into DHCOR SoM and AV96 board
Subsystems (3)
PATCH 1/1 ARM: dts: stm32: Split AV96 into DHCOR SoM and AV96 board
The AV96 is in fact an assembly of DH Electronics DHCOR SoM on top of an AV96 reference board. Split the DTs to reflect that and make sure to DHCOR SoM can be reused on other boards easily.
It is also highly recommended to configure the board for the DHCOM make stm32mp15_dhcom_basic_defconfig
make DEVICE_TREE=stm32mp15xx-dhcor-avenger96
as that permits reusing the board code for the DH components, like accessing and reading out the ethernet MAC from EEPROM.
---
arch/arm/dts/Makefile | 3 +-
arch/arm/dts/stm32mp157a-avenger96.dts | 393 +-----------------
.../stm32mp15xx-dhcor-avenger96-u-boot.dtsi | 80 ++++
arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts | 196 +++++++++
...oot.dtsi => stm32mp15xx-dhcor-u-boot.dtsi} | 79 +---
arch/arm/dts/stm32mp15xx-dhcor.dtsi | 220 ++++++++++
doc/board/st/stm32mp1.rst | 8 +-
7 files changed, 509 insertions(+), 470 deletions(-)
create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi
create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts
rename arch/arm/dts/{stm32mp157a-avenger96-u-boot.dtsi => stm32mp15xx-dhcor-u-boot.dtsi} (75%)
create mode 100644 arch/arm/dts/stm32mp15xx-dhcor.dtsiarch/arm/dts/Makefile +2 -1
@@ -884,7 +884,8 @@ dtb-$(CONFIG_STM32MP15x) += \ stm32mp157c-dk2.dtb \ stm32mp157c-ed1.dtb \ stm32mp157c-ev1.dtb \ - stm32mp15xx-dhcom-pdk2.dtb + stm32mp15xx-dhcom-pdk2.dtb \ + stm32mp15xx-dhcor-avenger96.dtb dtb-$(CONFIG_SOC_K3_AM6) += k3-am654-base-board.dtb k3-am654-r5-base-board.dtb dtb-$(CONFIG_SOC_K3_J721E) += k3-j721e-common-proc-board.dtb \
arch/arm/dts/stm32mp157a-avenger96.dts +2 -391
396 lines not on this page · raw message
arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi new file +80 -0
80 lines not on this page · raw message
arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts new file +196 -0
196 lines not on this page · raw message
arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi renamed from arch/arm/dts/stm32mp157a-avenger96-u-boot.dtsi +5 -74
103 lines not on this page · raw message
arch/arm/dts/stm32mp15xx-dhcor.dtsi new file +220 -0
220 lines not on this page · raw message
doc/board/st/stm32mp1.rst +4 -4
@@ -43,11 +43,11 @@ And the necessary drivers Currently the following boards are supported: - + stm32mp157a-avenger96.dts + stm32mp157a-dk1.dts + stm32mp157c-dk2.dts + stm32mp157c-ed1.dts + stm32mp157c-ev1.dts + + stm32mp15xx-dhcor-avenger96.dts Boot Sequences --------------
@@ -145,9 +145,9 @@ the supported device trees for STM32MP15x are: + stm32mp157c-dk2 -+ avenger96: Avenger96 board from Arrow Electronics ++ avenger96: Avenger96 board from Arrow Electronics based on DH Elec. DHCOR SoM - + stm32mp157a-avenger96 + + stm32mp15xx-dhcor-avenger96 Build Procedure ---------------
@@ -229,7 +229,7 @@ Build Procedure # export KBUILD_OUTPUT=stm32mp15_basic # make stm32mp15_basic_defconfig - # make DEVICE_TREE=stm32mp157a-avenger96 all + # make DEVICE_TREE=stm32mp15xx-dhcor-avenger96 all 6. Output files
Signature · 1 line
2.25.1
PATCH 1/1 ARM: dts: stm32: Split AV96 into DHCOR SoM and AV96 board
Hi Marek
Quoted 1,099 lines · Marek Vasut
The AV96 is in fact an assembly of DH Electronics DHCOR SoM on top of an AV96 reference board. Split the DTs to reflect that and make sure to DHCOR SoM can be reused on other boards easily.
It is also highly recommended to configure the board for the DHCOM make
stm32mp15_dhcom_basic_defconfig
make DEVICE_TREE=stm32mp15xx-dhcor-avenger96
as that permits reusing the board code for the DH components, like accessing and reading out the ethernet MAC from EEPROM.Signed-off-by Marek Vasut <[email protected]>Cc Patrick Delaunay <[email protected]>Cc Patrice Chotard <[email protected]>--- arch/arm/dts/Makefile | 3 +- arch/arm/dts/stm32mp157a-avenger96.dts | 393 +----------------- .../stm32mp15xx-dhcor-avenger96-u-boot.dtsi | 80 ++++ arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts | 196 +++++++++ ...oot.dtsi => stm32mp15xx-dhcor-u-boot.dtsi} | 79 +--- arch/arm/dts/stm32mp15xx-dhcor.dtsi | 220 ++++++++++ doc/board/st/stm32mp1.rst | 8 +- 7 files changed, 509 insertions(+), 470 deletions(-) create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts rename arch/arm/dts/{stm32mp157a-avenger96-u-boot.dtsi => stm32mp15xx-dhcor-u-boot.dtsi} (75%) create mode 100644 arch/arm/dts/stm32mp15xx-dhcor.dtsiarch/arm/dts/Makefile +2
-1@@ -884,7 +884,8 @@ dtb-$(CONFIG_STM32MP15x) += \ stm32mp157c-dk2.dtb \ stm32mp157c-ed1.dtb \ stm32mp157c-ev1.dtb \ - stm32mp15xx-dhcom-pdk2.dtb + stm32mp15xx-dhcom-pdk2.dtb \ + stm32mp15xx-dhcor-avenger96.dtb dtb-$(CONFIG_SOC_K3_AM6) += k3-am654-base-board.dtb k3-am654-r5-base-board.dtb dtb-$(CONFIG_SOC_K3_J721E) += k3-j721e-common-proc-board.dtb \arch/arm/dts/stm32mp157a-avenger96.dts +2
-391@@ -4,394 +4,5 @@ * Author: Manivannan Sadhasivam <[email protected]> */ -/dts-v1/; - -#include "stm32mp157c.dtsi" -#include "stm32mp157xac-pinctrl.dtsi" -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/mfd/st,stpmic1.h> - -/ { - model = "Arrow Electronics STM32MP157A Avenger96 board"; - compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157"; - - aliases { - ethernet0 = ðernet0; - mmc0 = &sdmmc1; - serial0 = &uart4; - serial1 = &uart7; - spi0 = &qspi; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - memory at c0000000 { - device_type = "memory"; - reg = <0xc0000000 0x40000000>; - }; - - led { - compatible = "gpio-leds"; - led1 { - label = "green:user1"; - gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "heartbeat"; - default-state = "off"; - }; - - led2 { - label = "green:user2"; - gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "mmc0"; - default-state = "off"; - }; - - led3 { - label = "green:user3"; - gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "mmc1"; - default-state = "off"; - }; - - led4 { - label = "green:user3"; - gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "none"; - default-state = "off"; - panic-indicator; - }; - - led5 { - label = "yellow:wifi"; - gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "phy0tx"; - default-state = "off"; - }; - - led6 { - label = "blue:bt"; - gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "bluetooth-power"; - default-state = "off"; - }; - }; -}; - -ðernet0 { - status = "okay"; - pinctrl-0 = <ðernet0_rgmii_pins_b>; - pinctrl-1 = <ðernet0_rgmii_pins_sleep_b>; - pinctrl-names = "default", "sleep"; - phy-mode = "rgmii"; - max-speed = <1000>; - phy-handle = <&phy0>; - phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>; - - mdio0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "snps,dwmac-mdio"; - phy0: ethernet-phy at 7 { - reg = <7>; - }; - }; -}; - -&i2c1 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_pins_b>; - i2c-scl-rising-time-ns = <185>; - i2c-scl-falling-time-ns = <20>; - status = "okay"; - /delete-property/dmas; - /delete-property/dma-names; -}; - -&i2c2 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c2_pins_b1 &i2c2_pins_b2>; - i2c-scl-rising-time-ns = <185>; - i2c-scl-falling-time-ns = <20>; - status = "okay"; - /delete-property/dmas; - /delete-property/dma-names; -}; - -&i2c4 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c4_pins_a>; - i2c-scl-rising-time-ns = <185>; - i2c-scl-falling-time-ns = <20>; - status = "okay"; - /delete-property/dmas; - /delete-property/dma-names; - - pmic: stpmic at 33 { - compatible = "st,stpmic1"; - reg = <0x33>; - interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>; - interrupt-controller; - #interrupt-cells = <2>; - status = "okay"; - - st,main-control-register = <0x04>; - st,vin-control-register = <0xc0>; - st,usb-control-register = <0x30>; - - regulators { - compatible = "st,stpmic1-regulators"; - - ldo1-supply = <&v3v3>; - ldo2-supply = <&v3v3>; - ldo3-supply = <&vdd_ddr>; - ldo5-supply = <&v3v3>; - ldo6-supply = <&v3v3>; - pwr_sw1-supply = <&bst_out>; - pwr_sw2-supply = <&bst_out>; - - vddcore: buck1 { - regulator-name = "vddcore"; - regulator-min-microvolt = <800000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-initial-mode = <0>; - regulator-over-current-protection; - }; - - vdd_ddr: buck2 { - regulator-name = "vdd_ddr"; - regulator-min-microvolt = <1350000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-initial-mode = <0>; - regulator-over-current-protection; - }; - - vdd: buck3 { - regulator-name = "vdd"; - regulator-min-microvolt = <2500000>; - regulator-max-microvolt = <2500000>; - regulator-always-on; - st,mask_reset; - regulator-initial-mode = <0>; - regulator-over-current-protection; - }; - - v3v3: buck4 { - regulator-name = "v3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-over-current-protection; - regulator-initial-mode = <0>; - }; - - vdda: ldo1 { - regulator-name = "vdda"; - regulator-min-microvolt = <2900000>; - regulator-max-microvolt = <2900000>; - interrupts = <IT_CURLIM_LDO1 0>; - interrupt-parent = <&pmic>; - }; - - v2v8: ldo2 { - regulator-name = "v2v8"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - interrupts = <IT_CURLIM_LDO2 0>; - interrupt-parent = <&pmic>; - }; - - vtt_ddr: ldo3 { - regulator-name = "vtt_ddr"; - regulator-min-microvolt = <0>; - regulator-max-microvolt = <1000000>; - regulator-always-on; - regulator-over-current-protection; - }; - - vdd_usb: ldo4 { - regulator-name = "vdd_usb"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - interrupts = <IT_CURLIM_LDO4 0>; - interrupt-parent = <&pmic>; - }; - - vdd_sd: ldo5 { - regulator-name = "vdd_sd"; - regulator-min-microvolt = <2900000>; - regulator-max-microvolt = <2900000>; - interrupts = <IT_CURLIM_LDO5 0>; - interrupt-parent = <&pmic>; - regulator-boot-on; - }; - - v1v8: ldo6 { - regulator-name = "v1v8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - interrupts = <IT_CURLIM_LDO6 0>; - interrupt-parent = <&pmic>; - regulator-enable-ramp-delay = <300000>; - }; - - vref_ddr: vref_ddr { - regulator-name = "vref_ddr"; - regulator-always-on; - regulator-over-current-protection; - }; - - bst_out: boost { - regulator-name = "bst_out"; - interrupts = <IT_OCP_BOOST 0>; - interrupt-parent = <&pmic>; - }; - - vbus_otg: pwr_sw1 { - regulator-name = "vbus_otg"; - interrupts = <IT_OCP_OTG 0>; - interrupt-parent = <&pmic>; - regulator-active-discharge = <1>; - }; - - vbus_sw: pwr_sw2 { - regulator-name = "vbus_sw"; - interrupts = <IT_OCP_SWOUT 0>; - interrupt-parent = <&pmic>; - regulator-active-discharge = <1>; - }; - }; - - onkey { - compatible = "st,stpmic1-onkey"; - interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>; - interrupt-names = "onkey-falling", "onkey-rising"; - status = "okay"; - }; - - watchdog { - compatible = "st,stpmic1-wdt"; - status = "disabled"; - }; - }; - - eeprom at 53 { - compatible = "atmel,24c02"; - reg = <0x53>; - pagesize = <16>; - }; -}; - -&iwdg2 { - timeout-sec = <32>; - status = "okay"; -}; - -&pwr_regulators { - vdd-supply = <&vdd>; - vdd_3v3_usbfs-supply = <&vdd_usb>; -}; - -&qspi { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>; - pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>; - reg = <0x58003000 0x1000>, <0x70000000 0x4000000>; - #address-cells = <1>; - #size-cells = <0>; - status = "okay"; - - flash0: mx66l51235l at 0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-rx-bus-width = <4>; - spi-max-frequency = <108000000>; - #address-cells = <1>; - #size-cells = <1>; - }; -}; - -&rng1 { - status = "okay"; -}; - -&rtc { - status = "okay"; -}; - -&sdmmc1 { - pinctrl-names = "default", "opendrain", "sleep"; - pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>; - pinctrl-1 = <&sdmmc1_b4_od_pins_a>; - pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; - broken-cd; - st,sig-dir; - st,neg-edge; - st,use-ckin; - bus-width = <4>; - vmmc-supply = <&vdd_sd>; - status = "okay"; -}; - -&sdmmc2 { - pinctrl-names = "default"; - pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>; - non-removable; - no-sd; - no-sdio; - st,neg-edge; - bus-width = <8>; - vmmc-supply = <&v3v3>; - mmc-ddr-3_3v; - status = "okay"; -}; - -&spi2 { - pinctrl-names = "default"; - pinctrl-0 = <&spi2_pins_a>; - status = "okay"; -}; - -&uart4 { - /* On Low speed expansion header */ - label = "LS-UART1"; - pinctrl-names = "default"; - pinctrl-0 = <&uart4_pins_b>; - status = "okay"; -}; - -&uart7 { - /* On Low speed expansion header */ - label = "LS-UART0"; - pinctrl-names = "default"; - pinctrl-0 = <&uart7_pins_a>; - status = "okay"; -}; - -&usbh_ehci { - phys = <&usbphyc_port0>; - phy-names = "usb"; - status = "okay"; -}; - -&usbotg_hs { - dr_mode = "peripheral"; - phys = <&usbphyc_port1 0>; - phy-names = "usb2-phy"; - status = "okay"; -}; - -&usbphyc { - status = "okay"; -}; - -&usbphyc_port0 { - phy-supply = <&vdd_usb>; -}; - -&usbphyc_port1 { - phy-supply = <&vdd_usb>; -}; +/* This is kept for backward compatibility and will be removed */ +#include "stm32mp15xx-dhcor-avenger96.dts"arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi new file +80
-0@@ -0,0 +1,80 @@ +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause +/* + * Copyright (C) 2020 Marek Vasut <[email protected]> + */ + +#include "stm32mp15xx-dhcor-u-boot.dtsi" + +/ { + aliases { + mmc0 = &sdmmc1; + mmc1 = &sdmmc2; + usb0 = &usbotg_hs; + }; + + config { + u-boot,boot-led = "led1"; + u-boot,error-led = "led4"; + }; +}; + +&sdmmc1 { + u-boot,dm-spl; +}; + +&sdmmc1_b4_pins_a { + u-boot,dm-spl; + pins { + u-boot,dm-spl; + }; +}; + +&sdmmc1_dir_pins_a { + u-boot,dm-spl; + pins1 { + u-boot,dm-spl; + }; + pins2 { + u-boot,dm-spl; + }; +}; + +&sdmmc2 { + u-boot,dm-spl; +}; + +&sdmmc2_b4_pins_a { + u-boot,dm-spl; + pins1 { + u-boot,dm-spl; + }; + pins2 { + u-boot,dm-spl; + }; +}; + +&sdmmc2_d47_pins_a { + u-boot,dm-spl; + pins { + u-boot,dm-spl; + }; +}; + +&uart4 { + u-boot,dm-pre-reloc; +}; + +&uart4_pins_b { + u-boot,dm-pre-reloc; + pins1 { + u-boot,dm-pre-reloc; + }; + pins2 { + u-boot,dm-pre-reloc; + }; +}; + +&usbotg_hs { + u-boot,force-b-session-valid; + hnp-srp-disable; +};arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts new file +196
-0@@ -0,0 +1,196 @@ +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) +/* + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved + * Author: Manivannan Sadhasivam <[email protected]> + * Copyright (C) 2020 Marek Vasut <[email protected]> + */ + +/dts-v1/; + +#include "stm32mp15xx-dhcor.dtsi" +#include "stm32mp15xx-dhcor-avenger96-u-boot.dtsi" + +/ { + model = "Arrow Electronics STM32MP15xx Avenger96 board"; + compatible = "arrow,stm32mp15xx-avenger96", "st,stm32mp15x"; + + aliases { + eeprom0 = &eeprom0; + ethernet0 = ðernet0; + mmc0 = &sdmmc1; + serial0 = &uart4; + serial1 = &uart7; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + led { + compatible = "gpio-leds"; + led1 { + label = "green:user1"; + gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led2 { + label = "green:user2"; + gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + + led3 { + label = "green:user3"; + gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc1"; + default-state = "off"; + }; + + led4 { + label = "green:user3"; + gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "none"; + default-state = "off"; + panic-indicator; + }; + + led5 { + label = "yellow:wifi"; + gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tx"; + default-state = "off"; + }; + + led6 { + label = "blue:bt"; + gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "bluetooth-power"; + default-state = "off"; + }; + }; +}; + +ðernet0 { + status = "okay"; + pinctrl-0 = <ðernet0_rgmii_pins_b>; + pinctrl-1 = <ðernet0_rgmii_pins_sleep_b>; + pinctrl-names = "default", "sleep"; + phy-mode = "rgmii"; + max-speed = <1000>; + phy-handle = <&phy0>; + phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + phy0: ethernet-phy at 7 { + reg = <7>; + }; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_b>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_b1 &i2c2_pins_b2>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; +}; + +&i2c4 { + eeprom0: eeprom at 53 { + compatible = "atmel,24c02"; + reg = <0x53>; + pagesize = <16>; + }; +}; + +&sdmmc1 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; + broken-cd; + st,sig-dir; + st,neg-edge; + st,use-ckin; + bus-width = <4>; + vmmc-supply = <&vdd_sd>; + status = "okay"; +}; + +&sdmmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>; + non-removable; + no-sd; + no-sdio; + st,neg-edge; + bus-width = <8>; + vmmc-supply = <&v3v3>; + mmc-ddr-3_3v; + status = "okay"; +}; + +&spi2 { + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins_a>; + status = "okay"; +}; + +&uart4 { + /* On Low speed expansion header */ + label = "LS-UART1"; + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins_b>; + status = "okay"; +}; + +&uart7 { + /* On Low speed expansion header */ + label = "LS-UART0"; + pinctrl-names = "default"; + pinctrl-0 = <&uart7_pins_a>; + status = "okay"; +}; + +&usbh_ehci { + phys = <&usbphyc_port0>; + phy-names = "usb"; + status = "okay"; +}; + +&usbotg_hs { + dr_mode = "peripheral"; + phys = <&usbphyc_port1 0>; + phy-names = "usb2-phy"; + status = "okay"; +}; + +&usbphyc { + status = "okay"; +}; + +&usbphyc_port0 { + phy-supply = <&vdd_usb>; +}; + +&usbphyc_port1 { + phy-supply = <&vdd_usb>; +};arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi renamed from arch/arm/dts/stm32mp157a-avenger96-u-boot.dtsi +5
-74@@ -4,25 +4,13 @@ * * Copyright (C) Linaro Ltd 2019 - All Rights Reserved * Author: Manivannan Sadhasivam <[email protected]> + * Copyright (C) 2020 Marek Vasut <[email protected]> */ #include <dt-bindings/clock/stm32mp1-clksrc.h> #include "stm32mp157-u-boot.dtsi" #include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi" -/ { - aliases { - mmc0 = &sdmmc1; - mmc1 = &sdmmc2; - usb0 = &usbotg_hs; - }; - - config { - u-boot,boot-led = "led1"; - u-boot,error-led = "led4"; - }; -}; - &i2c4 { u-boot,dm-pre-reloc; };@@ -38,6 +26,10 @@ u-boot,dm-pre-reloc; }; +&qspi { + u-boot,dm-spl; +}; + &rcc { st,clksrc = < CLK_MPU_PLL1P@@ -139,67 +131,6 @@ }; }; -&sdmmc1 { - u-boot,dm-spl; -}; - -&sdmmc1_b4_pins_a { - u-boot,dm-spl; - pins { - u-boot,dm-spl; - }; -}; - -&sdmmc1_dir_pins_a { - u-boot,dm-spl; - pins1 { - u-boot,dm-spl; - }; - pins2 { - u-boot,dm-spl; - }; -}; - -&sdmmc2 { - u-boot,dm-spl; -}; - -&sdmmc2_b4_pins_a { - u-boot,dm-spl; - pins1 { - u-boot,dm-spl; - }; - pins2 { - u-boot,dm-spl; - }; -}; - -&sdmmc2_d47_pins_a { - u-boot,dm-spl; - pins { - u-boot,dm-spl; - }; -}; - -&uart4 { - u-boot,dm-pre-reloc; -}; - -&uart4_pins_b { - u-boot,dm-pre-reloc; - pins1 { - u-boot,dm-pre-reloc; - }; - pins2 { - u-boot,dm-pre-reloc; - }; -}; - -&usbotg_hs { - u-boot,force-b-session-valid; - hnp-srp-disable; -}; - &v3v3 { regulator-always-on; };arch/arm/dts/stm32mp15xx-dhcor.dtsi new file +220
-0@@ -0,0 +1,220 @@ +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) +/* + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved + * Author: Manivannan Sadhasivam <[email protected]> + * Copyright (C) 2020 Marek Vasut <[email protected]> + */ +/dts-v1/; + +#include "stm32mp157c.dtsi" +#include "stm32mp157xac-pinctrl.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/mfd/st,stpmic1.h> + +/ { + aliases { + spi0 = &qspi; + }; + + memory at c0000000 { + device_type = "memory"; + reg = <0xc0000000 0x40000000>; + }; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; + + pmic: stpmic at 33 { + compatible = "st,stpmic1"; + reg = <0x33>; + interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + status = "okay"; + + st,main-control-register = <0x04>; + st,vin-control-register = <0xc0>; + st,usb-control-register = <0x30>; + + regulators { + compatible = "st,stpmic1-regulators"; + + ldo1-supply = <&v3v3>; + ldo2-supply = <&v3v3>; + ldo3-supply = <&vdd_ddr>; + ldo5-supply = <&v3v3>; + ldo6-supply = <&v3v3>; + pwr_sw1-supply = <&bst_out>; + pwr_sw2-supply = <&bst_out>; + + vddcore: buck1 { + regulator-name = "vddcore"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd_ddr: buck2 { + regulator-name = "vdd_ddr"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd: buck3 { + regulator-name = "vdd"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + st,mask_reset; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + v3v3: buck4 { + regulator-name = "v3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-over-current-protection; + regulator-initial-mode = <0>; + }; + + vdda: ldo1 { + regulator-name = "vdda"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + interrupts = <IT_CURLIM_LDO1 0>; + interrupt-parent = <&pmic>; + }; + + v2v8: ldo2 { + regulator-name = "v2v8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + interrupts = <IT_CURLIM_LDO2 0>; + interrupt-parent = <&pmic>; + }; + + vtt_ddr: ldo3 { + regulator-name = "vtt_ddr"; + regulator-min-microvolt = <0>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-over-current-protection; + }; + + vdd_usb: ldo4 { + regulator-name = "vdd_usb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + interrupts = <IT_CURLIM_LDO4 0>; + interrupt-parent = <&pmic>; + }; + + vdd_sd: ldo5 { + regulator-name = "vdd_sd"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + interrupts = <IT_CURLIM_LDO5 0>; + interrupt-parent = <&pmic>; + regulator-boot-on; + }; + + v1v8: ldo6 { + regulator-name = "v1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + interrupts = <IT_CURLIM_LDO6 0>; + interrupt-parent = <&pmic>; + regulator-enable-ramp-delay = <300000>; + }; + + vref_ddr: vref_ddr { + regulator-name = "vref_ddr"; + regulator-always-on; + regulator-over-current-protection; + }; + + bst_out: boost { + regulator-name = "bst_out"; + interrupts = <IT_OCP_BOOST 0>; + interrupt-parent = <&pmic>; + }; + + vbus_otg: pwr_sw1 { + regulator-name = "vbus_otg"; + interrupts = <IT_OCP_OTG 0>; + interrupt-parent = <&pmic>; + regulator-active-discharge = <1>; + }; + + vbus_sw: pwr_sw2 { + regulator-name = "vbus_sw"; + interrupts = <IT_OCP_SWOUT 0>; + interrupt-parent = <&pmic>; + regulator-active-discharge = <1>; + }; + }; + + onkey { + compatible = "st,stpmic1-onkey"; + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>; + interrupt-names = "onkey-falling", "onkey-rising"; + status = "okay"; + }; + + watchdog { + compatible = "st,stpmic1-wdt"; + status = "disabled"; + }; + }; +}; + +&iwdg2 { + timeout-sec = <32>; + status = "okay"; +}; + +&pwr_regulators { + vdd-supply = <&vdd>; + vdd_3v3_usbfs-supply = <&vdd_usb>; +}; + +&qspi { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>; + pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>; + reg = <0x58003000 0x1000>, <0x70000000 0x4000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + flash0: mx66l51235l at 0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +&rng1 { + status = "okay"; +}; + +&rtc { + status = "okay"; +};doc/board/st/stm32mp1.rst +3
-3@@ -43,11 +43,11 @@ And the necessary drivers Currently the following boards are supported: - + stm32mp157a-avenger96.dts + stm32mp157a-dk1.dts + stm32mp157c-dk2.dts + stm32mp157c-ed1.dts + stm32mp157c-ev1.dts + + stm32mp15xx-dhcor-avenger96.dts Boot Sequences --------------@@ -145,9 +145,9 @@ the supported device trees for STM32MP15x are: + stm32mp157c-dk2 -+ avenger96: Avenger96 board from Arrow Electronics ++ avenger96: Avenger96 board from Arrow Electronics based on DH Elec. DHCOR SoM - + stm32mp157a-avenger96 + + stm32mp15xx-dhcor-avenger96 Build Procedure ---------------
doc/board/st/stm32mp1.rst Build Procedure · line 235
Quoted 8 lines
doc/board/st/stm32mp1.rst +1
-1@@ -229,7 +229,7 @@ Build Procedure # export KBUILD_OUTPUT=stm32mp15_basic # make stm32mp15_basic_defconfig - # make DEVICE_TREE=stm32mp157a-avenger96 all + # make DEVICE_TREE=stm32mp15xx-dhcor-avenger96 all 6. Output files
Thanks
PATCH 1/1 ARM: dts: stm32: Split AV96 into DHCOR SoM and AV96 board
Quoted 1 line · Patrice CHOTARD
Hi Marek
Hi,
[...]
Quoted 21 lines
Quoted 21 lines
Boot Sequences
--------------doc/board/st/stm32mp1.rst +3
-3@@ -145,9 +145,9 @@ the supported device trees for STM32MP15x are: + stm32mp157c-dk2 -+ avenger96: Avenger96 board from Arrow Electronics ++ avenger96: Avenger96 board from Arrow Electronics based on DH Elec. DHCOR SoM - + stm32mp157a-avenger96 + + stm32mp15xx-dhcor-avenger96 Build Procedure ---------------@@ -229,7 +229,7 @@ Build Procedure # export KBUILD_OUTPUT=stm32mp15_basic # make stm32mp15_basic_defconfig - # make DEVICE_TREE=stm32mp157a-avenger96 all + # make DEVICE_TREE=stm32mp15xx-dhcor-avenger96 all
Quoted 6 lines
doc/board/st/stm32mp1.rst Build Procedure · line 235
Quoted 2 lines
doc/board/st/stm32mp1.rst +0
-06. Output filesReviewed-by Patrice Chotard <[email protected]>Thanks
It would be nice to get these AV96 fixes into 2020.04 release, because without all these, the board doesn't even boot :-( Do you have a branch with these patches applied, so I can check if something is missing ?
btw. please clip the email with [...], so it's easy to find the comments.