hwmon: lochnagar: Move binding over to dtschema
Subsystems (8)
Charles Keepax
maintainerPATCH v3 1/5 hwmon: lochnagar: Move binding over to dtschema
---
No changes since v2.
Thanks,
Charles
.../devicetree/bindings/hwmon/cirrus,lochnagar.txt | 26 ---------------- .../bindings/hwmon/cirrus,lochnagar.yaml | 35 ++++++++++++++++++++++ 2 files changed, 35 insertions(+), 26 deletions(-) delete mode 100644 Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.txt create mode 100644 Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.yaml
Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.txt deleted +0 -26
@@ -1,26 +0,0 @@ -Cirrus Logic Lochnagar Audio Development Board - -Lochnagar is an evaluation and development board for Cirrus Logic -Smart CODEC and Amp devices. It allows the connection of most Cirrus -Logic devices on mini-cards, as well as allowing connection of -various application processor systems to provide a full evaluation -platform. Audio system topology, clocking and power can all be -controlled through the Lochnagar, allowing the device under test -to be used in a variety of possible use cases. - -This binding document describes the binding for the hardware monitor -portion of the driver. - -This binding must be part of the Lochnagar MFD binding: - [4] ../mfd/cirrus,lochnagar.txt - -Required properties: - - - compatible : One of the following strings: - "cirrus,lochnagar2-hwmon" - -Example: - -lochnagar-hwmon { - compatible = "cirrus,lochnagar2-hwmon"; -};
Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.yaml new file +35 -0
@@ -0,0 +1,35 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/cirrus,lochnagar.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cirrus Logic Lochnagar Audio Development Board + +maintainers: + - [email protected] + +description: | + Lochnagar is an evaluation and development board for Cirrus Logic + Smart CODEC and Amp devices. It allows the connection of most Cirrus + Logic devices on mini-cards, as well as allowing connection of various + application processor systems to provide a full evaluation platform. + Audio system topology, clocking and power can all be controlled through + the Lochnagar, allowing the device under test to be used in a variety of + possible use cases. + + This binding document describes the binding for the hardware monitor + portion of the driver. + + This binding must be part of the Lochnagar MFD binding: + [1] ../mfd/cirrus,lochnagar.yaml + +properties: + compatible: + enum: + - cirrus,lochnagar2-hwmon + +required: + - compatible + +additionalProperties: false
Signature · 1 line
2.11.0
Charles Keepax
maintainerPATCH 2/5 ASoC: lochnagar: Move binding over to dtschema
---
No changes since v2.
Thanks,
Charles
.../devicetree/bindings/sound/cirrus,lochnagar.txt | 39 ---------------- .../bindings/sound/cirrus,lochnagar.yaml | 52 ++++++++++++++++++++++ 2 files changed, 52 insertions(+), 39 deletions(-) delete mode 100644 Documentation/devicetree/bindings/sound/cirrus,lochnagar.txt create mode 100644 Documentation/devicetree/bindings/sound/cirrus,lochnagar.yaml
Documentation/devicetree/bindings/sound/cirrus,lochnagar.txt deleted +0 -39
@@ -1,39 +0,0 @@ -Cirrus Logic Lochnagar Audio Development Board - -Lochnagar is an evaluation and development board for Cirrus Logic -Smart CODEC and Amp devices. It allows the connection of most Cirrus -Logic devices on mini-cards, as well as allowing connection of -various application processor systems to provide a full evaluation -platform. Audio system topology, clocking and power can all be -controlled through the Lochnagar, allowing the device under test -to be used in a variety of possible use cases. - -This binding document describes the binding for the audio portion -of the driver. - -This binding must be part of the Lochnagar MFD binding: - [4] ../mfd/cirrus,lochnagar.txt - -Required properties: - - - compatible : One of the following strings: - "cirrus,lochnagar2-soundcard" - - - #sound-dai-cells : Must be set to 1. - - - clocks : Contains an entry for each entry in clock-names. - - clock-names : Must include the following clocks: - "mclk" Master clock source for the sound card, should normally - be set to LOCHNAGAR_SOUNDCARD_MCLK provided by the Lochnagar - clock driver. - -Example: - -lochnagar-sc { - compatible = "cirrus,lochnagar2-soundcard"; - - #sound-dai-cells = <1>; - - clocks = <&lochnagar_clk LOCHNAGAR_SOUNDCARD_MCLK>; - clock-names = "mclk"; -};
Documentation/devicetree/bindings/sound/cirrus,lochnagar.yaml new file +52 -0
52 lines not on this page · raw message
Signature · 1 line
2.11.0
Re: [PATCH 2/5] ASoC: lochnagar: Move binding over to dtschema
Quoted 5 lines · Charles Keepax
Signed-off-by Charles Keepax <[email protected]>---
No changes since v2.
Quoted 9 lines
Thanks,
Charles.../devicetree/bindings/sound/cirrus,lochnagar.txt | 39 ---------------- .../bindings/sound/cirrus,lochnagar.yaml | 52 ++++++++++++++++++++++ 2 files changed, 52 insertions(+), 39 deletions(-) delete mode 100644 Documentation/devicetree/bindings/sound/cirrus,lochnagar.txt create mode 100644 Documentation/devicetree/bindings/sound/cirrus,lochnagar.yaml
Applied, thanks!
Charles Keepax
maintainerPATCH v3 3/5 pinctrl: lochnagar: Move binding over to dtschema
In reply to Charles Keepax---
Changes since v2:
- Removed description for gpio-controller
- Force pin node to be called pin-settings
- Simplify -pins pattern
- Add additional blank line
Thanks,
Charles
.../bindings/pinctrl/cirrus,lochnagar.txt | 141 --------------- .../bindings/pinctrl/cirrus,lochnagar.yaml | 190 +++++++++++++++++++++ 2 files changed, 190 insertions(+), 141 deletions(-) delete mode 100644 Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.txt create mode 100644 Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.yaml
Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.txt deleted +0 -141
@@ -1,141 +0,0 @@ -Cirrus Logic Lochnagar Audio Development Board - -Lochnagar is an evaluation and development board for Cirrus Logic -Smart CODEC and Amp devices. It allows the connection of most Cirrus -Logic devices on mini-cards, as well as allowing connection of -various application processor systems to provide a full evaluation -platform. Audio system topology, clocking and power can all be -controlled through the Lochnagar, allowing the device under test -to be used in a variety of possible use cases. - -This binding document describes the binding for the pinctrl portion -of the driver. - -Also see these documents for generic binding information: - [1] GPIO : ../gpio/gpio.txt - [2] Pinctrl: ../pinctrl/pinctrl-bindings.txt - -And these for relevant defines: - [3] include/dt-bindings/pinctrl/lochnagar.h - -This binding must be part of the Lochnagar MFD binding: - [4] ../mfd/cirrus,lochnagar.txt - -Required properties: - - - compatible : One of the following strings: - "cirrus,lochnagar-pinctrl" - - - gpio-controller : Indicates this device is a GPIO controller. - - #gpio-cells : Must be 2. The first cell is the pin number, see - [3] for available pins and the second cell is used to specify - optional parameters, see [1]. - - gpio-ranges : Range of pins managed by the GPIO controller, see - [1]. Both the GPIO and Pinctrl base should be set to zero and the - count to the appropriate of the LOCHNAGARx_PIN_NUM_GPIOS define, - see [3]. - - - pinctrl-names : A pinctrl state named "default" must be defined. - - pinctrl-0 : A phandle to the default pinctrl state. - -Required sub-nodes: - -The pin configurations are defined as a child of the pinctrl states -node, see [2]. Each sub-node can have the following properties: - - groups : A list of groups to select (either this or "pins" must be - specified), available groups: - codec-aif1, codec-aif2, codec-aif3, dsp-aif1, dsp-aif2, psia1, - psia2, gf-aif1, gf-aif2, gf-aif3, gf-aif4, spdif-aif, usb-aif1, - usb-aif2, adat-aif, soundcard-aif - - pins : A list of pin names to select (either this or "groups" must - be specified), available pins: - fpga-gpio1, fpga-gpio2, fpga-gpio3, fpga-gpio4, fpga-gpio5, - fpga-gpio6, codec-gpio1, codec-gpio2, codec-gpio3, codec-gpio4, - codec-gpio5, codec-gpio6, codec-gpio7, codec-gpio8, dsp-gpio1, - dsp-gpio2, dsp-gpio3, dsp-gpio4, dsp-gpio5, dsp-gpio6, gf-gpio2, - gf-gpio3, gf-gpio7, codec-aif1-bclk, codec-aif1-rxdat, - codec-aif1-lrclk, codec-aif1-txdat, codec-aif2-bclk, - codec-aif2-rxdat, codec-aif2-lrclk, codec-aif2-txdat, - codec-aif3-bclk, codec-aif3-rxdat, codec-aif3-lrclk, - codec-aif3-txdat, dsp-aif1-bclk, dsp-aif1-rxdat, dsp-aif1-lrclk, - dsp-aif1-txdat, dsp-aif2-bclk, dsp-aif2-rxdat, - dsp-aif2-lrclk, dsp-aif2-txdat, psia1-bclk, psia1-rxdat, - psia1-lrclk, psia1-txdat, psia2-bclk, psia2-rxdat, psia2-lrclk, - psia2-txdat, gf-aif3-bclk, gf-aif3-rxdat, gf-aif3-lrclk, - gf-aif3-txdat, gf-aif4-bclk, gf-aif4-rxdat, gf-aif4-lrclk, - gf-aif4-txdat, gf-aif1-bclk, gf-aif1-rxdat, gf-aif1-lrclk, - gf-aif1-txdat, gf-aif2-bclk, gf-aif2-rxdat, gf-aif2-lrclk, - gf-aif2-txdat, dsp-uart1-rx, dsp-uart1-tx, dsp-uart2-rx, - dsp-uart2-tx, gf-uart2-rx, gf-uart2-tx, usb-uart-rx, - codec-pdmclk1, codec-pdmdat1, codec-pdmclk2, codec-pdmdat2, - codec-dmicclk1, codec-dmicdat1, codec-dmicclk2, codec-dmicdat2, - codec-dmicclk3, codec-dmicdat3, codec-dmicclk4, codec-dmicdat4, - dsp-dmicclk1, dsp-dmicdat1, dsp-dmicclk2, dsp-dmicdat2, i2c2-scl, - i2c2-sda, i2c3-scl, i2c3-sda, i2c4-scl, i2c4-sda, dsp-standby, - codec-mclk1, codec-mclk2, dsp-clkin, psia1-mclk, psia2-mclk, - gf-gpio1, gf-gpio5, dsp-gpio20, led1, led2 - - function : The mux function to select, available functions: - aif, fpga-gpio1, fpga-gpio2, fpga-gpio3, fpga-gpio4, fpga-gpio5, - fpga-gpio6, codec-gpio1, codec-gpio2, codec-gpio3, codec-gpio4, - codec-gpio5, codec-gpio6, codec-gpio7, codec-gpio8, dsp-gpio1, - dsp-gpio2, dsp-gpio3, dsp-gpio4, dsp-gpio5, dsp-gpio6, gf-gpio2, - gf-gpio3, gf-gpio7, gf-gpio1, gf-gpio5, dsp-gpio20, codec-clkout, - dsp-clkout, pmic-32k, spdif-clkout, clk-12m288, clk-11m2986, - clk-24m576, clk-22m5792, xmos-mclk, gf-clkout1, gf-mclk1, - gf-mclk3, gf-mclk2, gf-clkout2, codec-mclk1, codec-mclk2, - dsp-clkin, psia1-mclk, psia2-mclk, spdif-mclk, codec-irq, - codec-reset, dsp-reset, dsp-irq, dsp-standby, codec-pdmclk1, - codec-pdmdat1, codec-pdmclk2, codec-pdmdat2, codec-dmicclk1, - codec-dmicdat1, codec-dmicclk2, codec-dmicdat2, codec-dmicclk3, - codec-dmicdat3, codec-dmicclk4, codec-dmicdat4, dsp-dmicclk1, - dsp-dmicdat1, dsp-dmicclk2, dsp-dmicdat2, dsp-uart1-rx, - dsp-uart1-tx, dsp-uart2-rx, dsp-uart2-tx, gf-uart2-rx, - gf-uart2-tx, usb-uart-rx, usb-uart-tx, i2c2-scl, i2c2-sda, - i2c3-scl, i2c3-sda, i2c4-scl, i2c4-sda, spdif-aif, psia1, - psia1-bclk, psia1-lrclk, psia1-rxdat, psia1-txdat, psia2, - psia2-bclk, psia2-lrclk, psia2-rxdat, psia2-txdat, codec-aif1, - codec-aif1-bclk, codec-aif1-lrclk, codec-aif1-rxdat, - codec-aif1-txdat, codec-aif2, codec-aif2-bclk, codec-aif2-lrclk, - codec-aif2-rxdat, codec-aif2-txdat, codec-aif3, codec-aif3-bclk, - codec-aif3-lrclk, codec-aif3-rxdat, codec-aif3-txdat, dsp-aif1, - dsp-aif1-bclk, dsp-aif1-lrclk, dsp-aif1-rxdat, dsp-aif1-txdat, - dsp-aif2, dsp-aif2-bclk, dsp-aif2-lrclk, dsp-aif2-rxdat, - dsp-aif2-txdat, gf-aif3, gf-aif3-bclk, gf-aif3-lrclk, - gf-aif3-rxdat, gf-aif3-txdat, gf-aif4, gf-aif4-bclk, - gf-aif4-lrclk, gf-aif4-rxdat, gf-aif4-txdat, gf-aif1, - gf-aif1-bclk, gf-aif1-lrclk, gf-aif1-rxdat, gf-aif1-txdat, - gf-aif2, gf-aif2-bclk, gf-aif2-lrclk, gf-aif2-rxdat, - gf-aif2-txdat, usb-aif1, usb-aif2, adat-aif, soundcard-aif, - - - output-enable : Specifies that an AIF group will be used as a master - interface (either this or input-enable is required if a group is - being muxed to an AIF) - - input-enable : Specifies that an AIF group will be used as a slave - interface (either this or output-enable is required if a group is - being muxed to an AIF) - -Example: - -lochnagar-pinctrl { - compatible = "cirrus,lochnagar-pinctrl"; - - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&lochnagar 0 0 LOCHNAGAR2_PIN_NUM_GPIOS>; - - pinctrl-names = "default"; - pinctrl-0 = <&pin-settings>; - - pin-settings: pin-settings { - ap-aif { - input-enable; - groups = "gf-aif1"; - function = "codec-aif3"; - }; - codec-aif { - output-enable; - groups = "codec-aif3"; - function = "gf-aif1"; - }; - }; -};
Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.yaml new file +190 -0
190 lines not on this page · raw message
Signature · 1 line
2.11.0
Re: [PATCH v3 3/5] pinctrl: lochnagar: Move binding over to dtschema
Quoted 9 lines · Charles Keepax
Signed-off-by Charles Keepax <[email protected]>---
Changes since v2:
- Removed description for gpio-controller
- Force pin node to be called pin-settings
- Simplify -pins pattern
- Add additional blank line
Quoted 9 lines
Thanks,
Charles.../bindings/pinctrl/cirrus,lochnagar.txt | 141 --------------- .../bindings/pinctrl/cirrus,lochnagar.yaml | 190 +++++++++++++++++++++ 2 files changed, 190 insertions(+), 141 deletions(-) delete mode 100644 Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.txt create mode 100644 Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.yaml
Applied, thanks!
Charles Keepax
maintainerPATCH v3 4/5 clk: lochnagar: Move binding over to dtschema
In reply to Charles Keepax---
No changes since v2.
Thanks,
Charles
.../devicetree/bindings/clock/cirrus,lochnagar.txt | 94 ---------------------- .../bindings/clock/cirrus,lochnagar.yaml | 78 ++++++++++++++++++ 2 files changed, 78 insertions(+), 94 deletions(-) delete mode 100644 Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt create mode 100644 Documentation/devicetree/bindings/clock/cirrus,lochnagar.yaml
Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt deleted +0 -94
@@ -1,94 +0,0 @@ -Cirrus Logic Lochnagar Audio Development Board - -Lochnagar is an evaluation and development board for Cirrus Logic -Smart CODEC and Amp devices. It allows the connection of most Cirrus -Logic devices on mini-cards, as well as allowing connection of -various application processor systems to provide a full evaluation -platform. Audio system topology, clocking and power can all be -controlled through the Lochnagar, allowing the device under test -to be used in a variety of possible use cases. - -This binding document describes the binding for the clock portion of -the driver. - -Also see these documents for generic binding information: - [1] Clock : ../clock/clock-bindings.txt - -And these for relevant defines: - [2] include/dt-bindings/clock/lochnagar.h - -This binding must be part of the Lochnagar MFD binding: - [3] ../mfd/cirrus,lochnagar.txt - -Required properties: - - - compatible : One of the following strings: - "cirrus,lochnagar1-clk" - "cirrus,lochnagar2-clk" - - - #clock-cells : Must be 1. The first cell indicates the clock - number, see [2] for available clocks and [1]. - -Optional properties: - - - clocks : Must contain an entry for each clock in clock-names. - - clock-names : May contain entries for each of the following - clocks: - - ln-cdc-clkout : Output clock from CODEC card. - - ln-dsp-clkout : Output clock from DSP card. - - ln-gf-mclk1,ln-gf-mclk2,ln-gf-mclk3,ln-gf-mclk4 : Optional - input audio clocks from host system. - - ln-psia1-mclk, ln-psia2-mclk : Optional input audio clocks from - external connector. - - ln-spdif-mclk : Optional input audio clock from SPDIF. - - ln-spdif-clkout : Optional input audio clock from SPDIF. - - ln-adat-mclk : Optional input audio clock from ADAT. - - ln-pmic-32k : On board fixed clock. - - ln-clk-12m : On board fixed clock. - - ln-clk-11m : On board fixed clock. - - ln-clk-24m : On board fixed clock. - - ln-clk-22m : On board fixed clock. - - ln-clk-8m : On board fixed clock. - - ln-usb-clk-24m : On board fixed clock. - - ln-usb-clk-12m : On board fixed clock. - - - assigned-clocks : A list of Lochnagar clocks to be reparented, see - [2] for available clocks. - - assigned-clock-parents : Parents to be assigned to the clocks - listed in "assigned-clocks". - -Optional nodes: - - - fixed-clock nodes may be registered for the following on board clocks: - - ln-pmic-32k : 32768 Hz - - ln-clk-12m : 12288000 Hz - - ln-clk-11m : 11298600 Hz - - ln-clk-24m : 24576000 Hz - - ln-clk-22m : 22579200 Hz - - ln-clk-8m : 8192000 Hz - - ln-usb-clk-24m : 24576000 Hz - - ln-usb-clk-12m : 12288000 Hz - -Example: - -lochnagar { - lochnagar-clk { - compatible = "cirrus,lochnagar2-clk"; - - #clock-cells = <1>; - - clocks = <&clk-audio>, <&clk_pmic>; - clock-names = "ln-gf-mclk2", "ln-pmic-32k"; - - assigned-clocks = <&lochnagar-clk LOCHNAGAR_CDC_MCLK1>, - <&lochnagar-clk LOCHNAGAR_CDC_MCLK2>; - assigned-clock-parents = <&clk-audio>, - <&clk-pmic>; - }; - - clk-pmic: clk-pmic { - compatible = "fixed-clock"; - clock-cells = <0>; - clock-frequency = <32768>; - }; -};
Documentation/devicetree/bindings/clock/cirrus,lochnagar.yaml new file +78 -0
78 lines not on this page · raw message
Signature · 1 line
2.11.0
Re: [PATCH v3 4/5] clk: lochnagar: Move binding over to dtschema
Quoted 5 lines · Charles Keepax
Signed-off-by Charles Keepax <[email protected]>---
No changes since v2.
Quoted 9 lines
Thanks,
Charles.../devicetree/bindings/clock/cirrus,lochnagar.txt | 94 ---------------------- .../bindings/clock/cirrus,lochnagar.yaml | 78 ++++++++++++++++++ 2 files changed, 78 insertions(+), 94 deletions(-) delete mode 100644 Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt create mode 100644 Documentation/devicetree/bindings/clock/cirrus,lochnagar.yaml
Applied, thanks!
Charles Keepax
maintainerPATCH v3 5/5 mfd: lochnagar: Move binding over to dtschema
In reply to Charles Keepax---
No changes since v2.
Thanks,
Charles
.../devicetree/bindings/mfd/cirrus,lochnagar.txt | 85 ----- .../devicetree/bindings/mfd/cirrus,lochnagar.yaml | 352 +++++++++++++++++++++ .../bindings/regulator/cirrus,lochnagar.txt | 82 ----- MAINTAINERS | 11 +- 4 files changed, 357 insertions(+), 173 deletions(-) delete mode 100644 Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt create mode 100644 Documentation/devicetree/bindings/mfd/cirrus,lochnagar.yaml delete mode 100644 Documentation/devicetree/bindings/regulator/cirrus,lochnagar.txt
Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt deleted +0 -85
@@ -1,85 +0,0 @@ -Cirrus Logic Lochnagar Audio Development Board - -Lochnagar is an evaluation and development board for Cirrus Logic -Smart CODEC and Amp devices. It allows the connection of most Cirrus -Logic devices on mini-cards, as well as allowing connection of -various application processor systems to provide a full evaluation -platform. Audio system topology, clocking and power can all be -controlled through the Lochnagar, allowing the device under test -to be used in a variety of possible use cases. - -Also see these documents for generic binding information: - [1] GPIO : ../gpio/gpio.txt - -And these for relevant defines: - [2] include/dt-bindings/pinctrl/lochnagar.h - [3] include/dt-bindings/clock/lochnagar.h - -And these documents for the required sub-node binding details: - [4] Clock: ../clock/cirrus,lochnagar.txt - [5] Pinctrl: ../pinctrl/cirrus,lochnagar.txt - [6] Regulator: ../regulator/cirrus,lochnagar.txt - [7] Sound: ../sound/cirrus,lochnagar.txt - [8] Hardware Monitor: ../hwmon/cirrus,lochnagar.txt - -Required properties: - - - compatible : One of the following strings: - "cirrus,lochnagar1" - "cirrus,lochnagar2" - - - reg : I2C slave address - - - reset-gpios : Reset line to the Lochnagar, see [1]. - -Required sub-nodes: - - - lochnagar-clk : Binding for the clocking components, see [4]. - - - lochnagar-pinctrl : Binding for the pin control components, see [5]. - -Optional sub-nodes: - - - Bindings for the regulator components, see [6]. Only available on - Lochnagar 2. - - - lochnagar-sc : Binding for the sound card components, see [7]. - Only available on Lochnagar 2. - - lochnagar-hwmon : Binding for the hardware monitor components, see [8]. - Only available on Lochnagar 2. - -Optional properties: - - - present-gpios : Host present line, indicating the presence of a - host system, see [1]. This can be omitted if the present line is - tied in hardware. - -Example: - -lochnagar: lochnagar@22 { - compatible = "cirrus,lochnagar2"; - reg = <0x22>; - - reset-gpios = <&gpio0 55 0>; - present-gpios = <&gpio0 60 0>; - - lochnagar-clk { - compatible = "cirrus,lochnagar2-clk"; - ... - }; - - lochnagar-pinctrl { - compatible = "cirrus,lochnagar-pinctrl"; - ... - }; - - lochnagar-sc { - compatible = "cirrus,lochnagar2-soundcard"; - ... - }; - - lochnagar-hwmon { - compatible = "cirrus,lochnagar2-hwmon"; - ... - }; -};
Documentation/devicetree/bindings/mfd/cirrus,lochnagar.yaml new file +352 -0
352 lines not on this page · raw message
Documentation/devicetree/bindings/regulator/cirrus,lochnagar.txt deleted +0 -82
82 lines not on this page · raw message
MAINTAINERS +5 -6
@@ -4062,12 +4062,11 @@ M: Charles Keepax <[email protected]> M: Richard Fitzgerald <[email protected]> L: [email protected] S: Supported -F: Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt -F: Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.txt -F: Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt -F: Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.txt -F: Documentation/devicetree/bindings/regulator/cirrus,lochnagar.txt -F: Documentation/devicetree/bindings/sound/cirrus,lochnagar.txt +F: Documentation/devicetree/bindings/clock/cirrus,lochnagar.yaml +F: Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.yaml +F: Documentation/devicetree/bindings/mfd/cirrus,lochnagar.yaml +F: Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.yaml +F: Documentation/devicetree/bindings/sound/cirrus,lochnagar.yaml F: Documentation/hwmon/lochnagar.rst F: drivers/clk/clk-lochnagar.c F: drivers/hwmon/lochnagar-hwmon.c
Signature · 1 line
2.11.0
Re: [PATCH v3 5/5] mfd: lochnagar: Move binding over to dtschema
Quoted 8 lines · Charles Keepax
Signed-off-by Charles Keepax <[email protected]>---
No changes since v2.
Thanks,
Charles
Quoted 9 lines
.../devicetree/bindings/mfd/cirrus,lochnagar.txt | 85 ----- .../devicetree/bindings/mfd/cirrus,lochnagar.yaml | 352 +++++++++++++++++++++ .../bindings/regulator/cirrus,lochnagar.txt | 82 ----- MAINTAINERS | 11 +- 4 files changed, 357 insertions(+), 173 deletions(-) delete mode 100644 Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt create mode 100644 Documentation/devicetree/bindings/mfd/cirrus,lochnagar.yaml delete mode 100644 Documentation/devicetree/bindings/regulator/cirrus,lochnagar.txt
Applied, thanks!
Quoted 5 lines · Charles Keepax
Signed-off-by Charles Keepax <[email protected]>---
No changes since v2.
Quoted 9 lines
Thanks,
Charles.../devicetree/bindings/hwmon/cirrus,lochnagar.txt | 26 ---------------- .../bindings/hwmon/cirrus,lochnagar.yaml | 35 ++++++++++++++++++++++ 2 files changed, 35 insertions(+), 26 deletions(-) delete mode 100644 Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.txt create mode 100644 Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.yaml
Applied, thanks!