Skip to contentSkip to conversation

hwmon: lochnagar: Move binding over to dtschema

PATCH Applied Charles Keepax 2 participants 10 messages May 12, 2020 – May 27, 2020

Subsystems (8)
lore
Share & tools
lore

Charles Keepax

author maintainer
#0 lore raw

PATCH v3 1/5 hwmon: lochnagar: Move binding over to dtschema

---

No changes since v2.

Thanks,
Charles

 .../devicetree/bindings/hwmon/cirrus,lochnagar.txt | 26 ----------------
 .../bindings/hwmon/cirrus,lochnagar.yaml           | 35 ++++++++++++++++++++++
 2 files changed, 35 insertions(+), 26 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.txt
 create mode 100644 Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.yaml
Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.txt deleted +0 -26
deleted file mode 100644
index ffb79ccf51ee3..0000000000000
@@ -1,26 +0,0 @@
-Cirrus Logic Lochnagar Audio Development Board
-
-Lochnagar is an evaluation and development board for Cirrus Logic
-Smart CODEC and Amp devices. It allows the connection of most Cirrus
-Logic devices on mini-cards, as well as allowing connection of
-various application processor systems to provide a full evaluation
-platform.  Audio system topology, clocking and power can all be
-controlled through the Lochnagar, allowing the device under test
-to be used in a variety of possible use cases.
-
-This binding document describes the binding for the hardware monitor
-portion of the driver.
-
-This binding must be part of the Lochnagar MFD binding:
-  [4] ../mfd/cirrus,lochnagar.txt
-
-Required properties:
-
-  - compatible : One of the following strings:
-                 "cirrus,lochnagar2-hwmon"
-
-Example:
-
-lochnagar-hwmon {
-	compatible = "cirrus,lochnagar2-hwmon";
-};
Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.yaml new file +35 -0
new file mode 100644
index 0000000000000..cc00b97a7dace
@@ -0,0 +1,35 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/hwmon/cirrus,lochnagar.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cirrus Logic Lochnagar Audio Development Board
+
+maintainers:
+  - [email protected]
+
+description: |
+  Lochnagar is an evaluation and development board for Cirrus Logic
+  Smart CODEC and Amp devices. It allows the connection of most Cirrus
+  Logic devices on mini-cards, as well as allowing connection of various
+  application processor systems to provide a full evaluation platform.
+  Audio system topology, clocking and power can all be controlled through
+  the Lochnagar, allowing the device under test to be used in a variety of
+  possible use cases.
+
+  This binding document describes the binding for the hardware monitor
+  portion of the driver.
+
+  This binding must be part of the Lochnagar MFD binding:
+    [1] ../mfd/cirrus,lochnagar.yaml
+
+properties:
+  compatible:
+    enum:
+      - cirrus,lochnagar2-hwmon
+
+required:
+  - compatible
+
+additionalProperties: false
Signature · 1 line
2.11.0
author maintainer
#1 lore raw

PATCH 2/5 ASoC: lochnagar: Move binding over to dtschema

---

No changes since v2.

Thanks,
Charles

 .../devicetree/bindings/sound/cirrus,lochnagar.txt | 39 ----------------
 .../bindings/sound/cirrus,lochnagar.yaml           | 52 ++++++++++++++++++++++
 2 files changed, 52 insertions(+), 39 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/sound/cirrus,lochnagar.txt
 create mode 100644 Documentation/devicetree/bindings/sound/cirrus,lochnagar.yaml
Documentation/devicetree/bindings/sound/cirrus,lochnagar.txt deleted +0 -39
deleted file mode 100644
index 41ae2699f07a9..0000000000000
@@ -1,39 +0,0 @@
-Cirrus Logic Lochnagar Audio Development Board
-
-Lochnagar is an evaluation and development board for Cirrus Logic
-Smart CODEC and Amp devices. It allows the connection of most Cirrus
-Logic devices on mini-cards, as well as allowing connection of
-various application processor systems to provide a full evaluation
-platform.  Audio system topology, clocking and power can all be
-controlled through the Lochnagar, allowing the device under test
-to be used in a variety of possible use cases.
-
-This binding document describes the binding for the audio portion
-of the driver.
-
-This binding must be part of the Lochnagar MFD binding:
-  [4] ../mfd/cirrus,lochnagar.txt
-
-Required properties:
-
-  - compatible : One of the following strings:
-                 "cirrus,lochnagar2-soundcard"
-
-  - #sound-dai-cells : Must be set to 1.
-
-  - clocks : Contains an entry for each entry in clock-names.
-  - clock-names : Must include the following clocks:
-      "mclk" Master clock source for the sound card, should normally
-      be set to LOCHNAGAR_SOUNDCARD_MCLK provided by the Lochnagar
-      clock driver.
-
-Example:
-
-lochnagar-sc {
-	compatible = "cirrus,lochnagar2-soundcard";
-
-	#sound-dai-cells = <1>;
-
-	clocks = <&lochnagar_clk LOCHNAGAR_SOUNDCARD_MCLK>;
-	clock-names = "mclk";
-};
Documentation/devicetree/bindings/sound/cirrus,lochnagar.yaml new file +52 -0

52 lines not on this page · raw message

Signature · 1 line
2.11.0
maintainer Applied
#2 lore raw

Re: [PATCH 2/5] ASoC: lochnagar: Move binding over to dtschema

Quoted 5 lines · Charles Keepax

---

No changes since v2.

Quoted 9 lines

Thanks,
Charles

 .../devicetree/bindings/sound/cirrus,lochnagar.txt | 39 ----------------
 .../bindings/sound/cirrus,lochnagar.yaml           | 52 ++++++++++++++++++++++
 2 files changed, 52 insertions(+), 39 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/sound/cirrus,lochnagar.txt
 create mode 100644 Documentation/devicetree/bindings/sound/cirrus,lochnagar.yaml

Applied, thanks!

author maintainer
#3 lore raw

PATCH v3 3/5 pinctrl: lochnagar: Move binding over to dtschema

In reply to Charles Keepax

---

Changes since v2:
- Removed description for gpio-controller
- Force pin node to be called pin-settings
- Simplify -pins pattern
- Add additional blank line

Thanks,
Charles

 .../bindings/pinctrl/cirrus,lochnagar.txt          | 141 ---------------
 .../bindings/pinctrl/cirrus,lochnagar.yaml         | 190 +++++++++++++++++++++
 2 files changed, 190 insertions(+), 141 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.txt
 create mode 100644 Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.yaml
Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.txt deleted +0 -141
deleted file mode 100644
index a87447180e838..0000000000000
@@ -1,141 +0,0 @@
-Cirrus Logic Lochnagar Audio Development Board
-
-Lochnagar is an evaluation and development board for Cirrus Logic
-Smart CODEC and Amp devices. It allows the connection of most Cirrus
-Logic devices on mini-cards, as well as allowing connection of
-various application processor systems to provide a full evaluation
-platform.  Audio system topology, clocking and power can all be
-controlled through the Lochnagar, allowing the device under test
-to be used in a variety of possible use cases.
-
-This binding document describes the binding for the pinctrl portion
-of the driver.
-
-Also see these documents for generic binding information:
-  [1] GPIO : ../gpio/gpio.txt
-  [2] Pinctrl: ../pinctrl/pinctrl-bindings.txt
-
-And these for relevant defines:
-  [3] include/dt-bindings/pinctrl/lochnagar.h
-
-This binding must be part of the Lochnagar MFD binding:
-  [4] ../mfd/cirrus,lochnagar.txt
-
-Required properties:
-
-  - compatible : One of the following strings:
-                 "cirrus,lochnagar-pinctrl"
-
-  - gpio-controller : Indicates this device is a GPIO controller.
-  - #gpio-cells : Must be 2. The first cell is the pin number, see
-    [3] for available pins and the second cell is used to specify
-    optional parameters, see [1].
-  - gpio-ranges : Range of pins managed by the GPIO controller, see
-    [1]. Both the GPIO and Pinctrl base should be set to zero and the
-    count to the appropriate of the LOCHNAGARx_PIN_NUM_GPIOS define,
-    see [3].
-
-  - pinctrl-names : A pinctrl state named "default" must be defined.
-  - pinctrl-0 : A phandle to the default pinctrl state.
-
-Required sub-nodes:
-
-The pin configurations are defined as a child of the pinctrl states
-node, see [2]. Each sub-node can have the following properties:
-  - groups : A list of groups to select (either this or "pins" must be
-    specified), available groups:
-      codec-aif1, codec-aif2, codec-aif3, dsp-aif1, dsp-aif2, psia1,
-      psia2, gf-aif1, gf-aif2, gf-aif3, gf-aif4, spdif-aif, usb-aif1,
-      usb-aif2, adat-aif, soundcard-aif
-  - pins : A list of pin names to select (either this or "groups" must
-    be specified), available pins:
-      fpga-gpio1, fpga-gpio2, fpga-gpio3, fpga-gpio4, fpga-gpio5,
-      fpga-gpio6, codec-gpio1, codec-gpio2, codec-gpio3, codec-gpio4,
-      codec-gpio5, codec-gpio6, codec-gpio7, codec-gpio8, dsp-gpio1,
-      dsp-gpio2, dsp-gpio3, dsp-gpio4, dsp-gpio5, dsp-gpio6, gf-gpio2,
-      gf-gpio3, gf-gpio7, codec-aif1-bclk, codec-aif1-rxdat,
-      codec-aif1-lrclk, codec-aif1-txdat, codec-aif2-bclk,
-      codec-aif2-rxdat, codec-aif2-lrclk, codec-aif2-txdat,
-      codec-aif3-bclk, codec-aif3-rxdat, codec-aif3-lrclk,
-      codec-aif3-txdat, dsp-aif1-bclk, dsp-aif1-rxdat, dsp-aif1-lrclk,
-      dsp-aif1-txdat, dsp-aif2-bclk, dsp-aif2-rxdat,
-      dsp-aif2-lrclk, dsp-aif2-txdat, psia1-bclk, psia1-rxdat,
-      psia1-lrclk, psia1-txdat, psia2-bclk, psia2-rxdat, psia2-lrclk,
-      psia2-txdat, gf-aif3-bclk, gf-aif3-rxdat, gf-aif3-lrclk,
-      gf-aif3-txdat, gf-aif4-bclk, gf-aif4-rxdat, gf-aif4-lrclk,
-      gf-aif4-txdat, gf-aif1-bclk, gf-aif1-rxdat, gf-aif1-lrclk,
-      gf-aif1-txdat, gf-aif2-bclk, gf-aif2-rxdat, gf-aif2-lrclk,
-      gf-aif2-txdat, dsp-uart1-rx, dsp-uart1-tx, dsp-uart2-rx,
-      dsp-uart2-tx, gf-uart2-rx, gf-uart2-tx, usb-uart-rx,
-      codec-pdmclk1, codec-pdmdat1, codec-pdmclk2, codec-pdmdat2,
-      codec-dmicclk1, codec-dmicdat1, codec-dmicclk2, codec-dmicdat2,
-      codec-dmicclk3, codec-dmicdat3, codec-dmicclk4, codec-dmicdat4,
-      dsp-dmicclk1, dsp-dmicdat1, dsp-dmicclk2, dsp-dmicdat2, i2c2-scl,
-      i2c2-sda, i2c3-scl, i2c3-sda, i2c4-scl, i2c4-sda, dsp-standby,
-      codec-mclk1, codec-mclk2, dsp-clkin, psia1-mclk, psia2-mclk,
-      gf-gpio1, gf-gpio5, dsp-gpio20, led1, led2
-  - function : The mux function to select, available functions:
-      aif, fpga-gpio1, fpga-gpio2, fpga-gpio3, fpga-gpio4, fpga-gpio5,
-      fpga-gpio6, codec-gpio1, codec-gpio2, codec-gpio3, codec-gpio4,
-      codec-gpio5, codec-gpio6, codec-gpio7, codec-gpio8, dsp-gpio1,
-      dsp-gpio2, dsp-gpio3, dsp-gpio4, dsp-gpio5, dsp-gpio6, gf-gpio2,
-      gf-gpio3, gf-gpio7, gf-gpio1, gf-gpio5, dsp-gpio20, codec-clkout,
-      dsp-clkout, pmic-32k, spdif-clkout, clk-12m288, clk-11m2986,
-      clk-24m576, clk-22m5792, xmos-mclk, gf-clkout1, gf-mclk1,
-      gf-mclk3, gf-mclk2, gf-clkout2, codec-mclk1, codec-mclk2,
-      dsp-clkin, psia1-mclk, psia2-mclk, spdif-mclk, codec-irq,
-      codec-reset, dsp-reset, dsp-irq, dsp-standby, codec-pdmclk1,
-      codec-pdmdat1, codec-pdmclk2, codec-pdmdat2, codec-dmicclk1,
-      codec-dmicdat1, codec-dmicclk2, codec-dmicdat2, codec-dmicclk3,
-      codec-dmicdat3, codec-dmicclk4, codec-dmicdat4, dsp-dmicclk1,
-      dsp-dmicdat1, dsp-dmicclk2, dsp-dmicdat2, dsp-uart1-rx,
-      dsp-uart1-tx, dsp-uart2-rx, dsp-uart2-tx, gf-uart2-rx,
-      gf-uart2-tx, usb-uart-rx, usb-uart-tx, i2c2-scl, i2c2-sda,
-      i2c3-scl, i2c3-sda, i2c4-scl, i2c4-sda, spdif-aif, psia1,
-      psia1-bclk, psia1-lrclk, psia1-rxdat, psia1-txdat, psia2,
-      psia2-bclk, psia2-lrclk, psia2-rxdat, psia2-txdat, codec-aif1,
-      codec-aif1-bclk, codec-aif1-lrclk, codec-aif1-rxdat,
-      codec-aif1-txdat, codec-aif2, codec-aif2-bclk, codec-aif2-lrclk,
-      codec-aif2-rxdat, codec-aif2-txdat, codec-aif3, codec-aif3-bclk,
-      codec-aif3-lrclk, codec-aif3-rxdat, codec-aif3-txdat, dsp-aif1,
-      dsp-aif1-bclk, dsp-aif1-lrclk, dsp-aif1-rxdat, dsp-aif1-txdat,
-      dsp-aif2, dsp-aif2-bclk, dsp-aif2-lrclk, dsp-aif2-rxdat,
-      dsp-aif2-txdat, gf-aif3, gf-aif3-bclk, gf-aif3-lrclk,
-      gf-aif3-rxdat, gf-aif3-txdat, gf-aif4, gf-aif4-bclk,
-      gf-aif4-lrclk, gf-aif4-rxdat, gf-aif4-txdat, gf-aif1,
-      gf-aif1-bclk, gf-aif1-lrclk, gf-aif1-rxdat, gf-aif1-txdat,
-      gf-aif2, gf-aif2-bclk, gf-aif2-lrclk, gf-aif2-rxdat,
-      gf-aif2-txdat, usb-aif1, usb-aif2, adat-aif, soundcard-aif,
-
-  - output-enable : Specifies that an AIF group will be used as a master
-    interface (either this or input-enable is required if a group is
-    being muxed to an AIF)
-  - input-enable : Specifies that an AIF group will be used as a slave
-    interface (either this or output-enable is required if a group is
-    being muxed to an AIF)
-
-Example:
-
-lochnagar-pinctrl {
-	compatible = "cirrus,lochnagar-pinctrl";
-
-	gpio-controller;
-	#gpio-cells = <2>;
-	gpio-ranges = <&lochnagar 0 0 LOCHNAGAR2_PIN_NUM_GPIOS>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pin-settings>;
-
-	pin-settings: pin-settings {
-		ap-aif {
-			input-enable;
-			groups = "gf-aif1";
-			function = "codec-aif3";
-		};
-		codec-aif {
-			output-enable;
-			groups = "codec-aif3";
-			function = "gf-aif1";
-		};
-	};
-};
Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.yaml new file +190 -0

190 lines not on this page · raw message

Signature · 1 line
2.11.0
maintainer Applied
#4 lore raw

Re: [PATCH v3 3/5] pinctrl: lochnagar: Move binding over to dtschema

Quoted 9 lines · Charles Keepax

---

Changes since v2:
- Removed description for gpio-controller
- Force pin node to be called pin-settings
- Simplify -pins pattern
- Add additional blank line

Quoted 9 lines

Thanks,
Charles

 .../bindings/pinctrl/cirrus,lochnagar.txt          | 141 ---------------
 .../bindings/pinctrl/cirrus,lochnagar.yaml         | 190 +++++++++++++++++++++
 2 files changed, 190 insertions(+), 141 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.txt
 create mode 100644 Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.yaml

Applied, thanks!

author maintainer
#5 lore raw

PATCH v3 4/5 clk: lochnagar: Move binding over to dtschema

In reply to Charles Keepax

---

No changes since v2.

Thanks,
Charles

 .../devicetree/bindings/clock/cirrus,lochnagar.txt | 94 ----------------------
 .../bindings/clock/cirrus,lochnagar.yaml           | 78 ++++++++++++++++++
 2 files changed, 78 insertions(+), 94 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt
 create mode 100644 Documentation/devicetree/bindings/clock/cirrus,lochnagar.yaml
Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt deleted +0 -94
deleted file mode 100644
index 52a064c789eec..0000000000000
@@ -1,94 +0,0 @@
-Cirrus Logic Lochnagar Audio Development Board
-
-Lochnagar is an evaluation and development board for Cirrus Logic
-Smart CODEC and Amp devices. It allows the connection of most Cirrus
-Logic devices on mini-cards, as well as allowing connection of
-various application processor systems to provide a full evaluation
-platform.  Audio system topology, clocking and power can all be
-controlled through the Lochnagar, allowing the device under test
-to be used in a variety of possible use cases.
-
-This binding document describes the binding for the clock portion of
-the driver.
-
-Also see these documents for generic binding information:
-  [1] Clock : ../clock/clock-bindings.txt
-
-And these for relevant defines:
-  [2] include/dt-bindings/clock/lochnagar.h
-
-This binding must be part of the Lochnagar MFD binding:
-  [3] ../mfd/cirrus,lochnagar.txt
-
-Required properties:
-
-  - compatible : One of the following strings:
-                 "cirrus,lochnagar1-clk"
-                 "cirrus,lochnagar2-clk"
-
-  - #clock-cells : Must be 1. The first cell indicates the clock
-    number, see [2] for available clocks and [1].
-
-Optional properties:
-
-  - clocks : Must contain an entry for each clock in clock-names.
-  - clock-names : May contain entries for each of the following
-    clocks:
-     - ln-cdc-clkout : Output clock from CODEC card.
-     - ln-dsp-clkout : Output clock from DSP card.
-     - ln-gf-mclk1,ln-gf-mclk2,ln-gf-mclk3,ln-gf-mclk4 : Optional
-       input audio clocks from host system.
-     - ln-psia1-mclk, ln-psia2-mclk : Optional input audio clocks from
-       external connector.
-     - ln-spdif-mclk : Optional input audio clock from SPDIF.
-     - ln-spdif-clkout : Optional input audio clock from SPDIF.
-     - ln-adat-mclk : Optional input audio clock from ADAT.
-     - ln-pmic-32k : On board fixed clock.
-     - ln-clk-12m : On board fixed clock.
-     - ln-clk-11m : On board fixed clock.
-     - ln-clk-24m : On board fixed clock.
-     - ln-clk-22m : On board fixed clock.
-     - ln-clk-8m : On board fixed clock.
-     - ln-usb-clk-24m : On board fixed clock.
-     - ln-usb-clk-12m : On board fixed clock.
-
-  - assigned-clocks : A list of Lochnagar clocks to be reparented, see
-    [2] for available clocks.
-  - assigned-clock-parents : Parents to be assigned to the clocks
-    listed in "assigned-clocks".
-
-Optional nodes:
-
-  - fixed-clock nodes may be registered for the following on board clocks:
-     - ln-pmic-32k : 32768 Hz
-     - ln-clk-12m : 12288000 Hz
-     - ln-clk-11m : 11298600 Hz
-     - ln-clk-24m : 24576000 Hz
-     - ln-clk-22m : 22579200 Hz
-     - ln-clk-8m : 8192000 Hz
-     - ln-usb-clk-24m : 24576000 Hz
-     - ln-usb-clk-12m : 12288000 Hz
-
-Example:
-
-lochnagar {
-	lochnagar-clk {
-		compatible = "cirrus,lochnagar2-clk";
-
-		#clock-cells = <1>;
-
-		clocks = <&clk-audio>, <&clk_pmic>;
-		clock-names = "ln-gf-mclk2", "ln-pmic-32k";
-
-		assigned-clocks = <&lochnagar-clk LOCHNAGAR_CDC_MCLK1>,
-				  <&lochnagar-clk LOCHNAGAR_CDC_MCLK2>;
-		assigned-clock-parents = <&clk-audio>,
-					 <&clk-pmic>;
-	};
-
-	clk-pmic: clk-pmic {
-		compatible = "fixed-clock";
-		clock-cells = <0>;
-		clock-frequency = <32768>;
-	};
-};
Documentation/devicetree/bindings/clock/cirrus,lochnagar.yaml new file +78 -0

78 lines not on this page · raw message

Signature · 1 line
2.11.0
maintainer Applied
#6 lore raw

Re: [PATCH v3 4/5] clk: lochnagar: Move binding over to dtschema

Quoted 5 lines · Charles Keepax

---

No changes since v2.

Quoted 9 lines

Thanks,
Charles

 .../devicetree/bindings/clock/cirrus,lochnagar.txt | 94 ----------------------
 .../bindings/clock/cirrus,lochnagar.yaml           | 78 ++++++++++++++++++
 2 files changed, 78 insertions(+), 94 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt
 create mode 100644 Documentation/devicetree/bindings/clock/cirrus,lochnagar.yaml

Applied, thanks!

author maintainer
#7 lore raw

PATCH v3 5/5 mfd: lochnagar: Move binding over to dtschema

In reply to Charles Keepax

---

No changes since v2.

Thanks,
Charles

 .../devicetree/bindings/mfd/cirrus,lochnagar.txt   |  85 -----
 .../devicetree/bindings/mfd/cirrus,lochnagar.yaml  | 352 +++++++++++++++++++++
 .../bindings/regulator/cirrus,lochnagar.txt        |  82 -----
 MAINTAINERS                                        |  11 +-
 4 files changed, 357 insertions(+), 173 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt
 create mode 100644 Documentation/devicetree/bindings/mfd/cirrus,lochnagar.yaml
 delete mode 100644 Documentation/devicetree/bindings/regulator/cirrus,lochnagar.txt
Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt deleted +0 -85
deleted file mode 100644
index 3bf92ad37fa1b..0000000000000
@@ -1,85 +0,0 @@
-Cirrus Logic Lochnagar Audio Development Board
-
-Lochnagar is an evaluation and development board for Cirrus Logic
-Smart CODEC and Amp devices. It allows the connection of most Cirrus
-Logic devices on mini-cards, as well as allowing connection of
-various application processor systems to provide a full evaluation
-platform.  Audio system topology, clocking and power can all be
-controlled through the Lochnagar, allowing the device under test
-to be used in a variety of possible use cases.
-
-Also see these documents for generic binding information:
-  [1] GPIO : ../gpio/gpio.txt
-
-And these for relevant defines:
-  [2] include/dt-bindings/pinctrl/lochnagar.h
-  [3] include/dt-bindings/clock/lochnagar.h
-
-And these documents for the required sub-node binding details:
-  [4] Clock: ../clock/cirrus,lochnagar.txt
-  [5] Pinctrl: ../pinctrl/cirrus,lochnagar.txt
-  [6] Regulator: ../regulator/cirrus,lochnagar.txt
-  [7] Sound: ../sound/cirrus,lochnagar.txt
-  [8] Hardware Monitor: ../hwmon/cirrus,lochnagar.txt
-
-Required properties:
-
-  - compatible : One of the following strings:
-                 "cirrus,lochnagar1"
-                 "cirrus,lochnagar2"
-
-  - reg : I2C slave address
-
-  - reset-gpios : Reset line to the Lochnagar, see [1].
-
-Required sub-nodes:
-
-  - lochnagar-clk : Binding for the clocking components, see [4].
-
-  - lochnagar-pinctrl : Binding for the pin control components, see [5].
-
-Optional sub-nodes:
-
-  - Bindings for the regulator components, see [6]. Only available on
-    Lochnagar 2.
-
-  - lochnagar-sc : Binding for the sound card components, see [7].
-                   Only available on Lochnagar 2.
-  - lochnagar-hwmon : Binding for the hardware monitor components, see [8].
-                      Only available on Lochnagar 2.
-
-Optional properties:
-
-  - present-gpios : Host present line, indicating the presence of a
-    host system, see [1]. This can be omitted if the present line is
-    tied in hardware.
-
-Example:
-
-lochnagar: lochnagar@22 {
-	compatible = "cirrus,lochnagar2";
-	reg = <0x22>;
-
-	reset-gpios = <&gpio0 55 0>;
-	present-gpios = <&gpio0 60 0>;
-
-	lochnagar-clk {
-		compatible = "cirrus,lochnagar2-clk";
-		...
-	};
-
-	lochnagar-pinctrl {
-		compatible = "cirrus,lochnagar-pinctrl";
-		...
-	};
-
-	lochnagar-sc {
-		compatible = "cirrus,lochnagar2-soundcard";
-		...
-	};
-
-	lochnagar-hwmon {
-		compatible = "cirrus,lochnagar2-hwmon";
-		...
-	};
-};
Documentation/devicetree/bindings/mfd/cirrus,lochnagar.yaml new file +352 -0

352 lines not on this page · raw message

Documentation/devicetree/bindings/regulator/cirrus,lochnagar.txt deleted +0 -82

82 lines not on this page · raw message

MAINTAINERS +5 -6
index e64e5db314976..91bf1fbe98c8e 100644
@@ -4062,12 +4062,11 @@ M:	Charles Keepax <[email protected]>
 M:	Richard Fitzgerald <[email protected]>
 L:	[email protected]
 S:	Supported
-F:	Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt
-F:	Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.txt
-F:	Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt
-F:	Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.txt
-F:	Documentation/devicetree/bindings/regulator/cirrus,lochnagar.txt
-F:	Documentation/devicetree/bindings/sound/cirrus,lochnagar.txt
+F:	Documentation/devicetree/bindings/clock/cirrus,lochnagar.yaml
+F:	Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.yaml
+F:	Documentation/devicetree/bindings/mfd/cirrus,lochnagar.yaml
+F:	Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.yaml
+F:	Documentation/devicetree/bindings/sound/cirrus,lochnagar.yaml
 F:	Documentation/hwmon/lochnagar.rst
 F:	drivers/clk/clk-lochnagar.c
 F:	drivers/hwmon/lochnagar-hwmon.c
Signature · 1 line
2.11.0
maintainer Applied
#8 lore raw

Re: [PATCH v3 5/5] mfd: lochnagar: Move binding over to dtschema

Quoted 8 lines · Charles Keepax

---

No changes since v2.

Thanks,
Charles

Quoted 9 lines
 .../devicetree/bindings/mfd/cirrus,lochnagar.txt   |  85 -----
 .../devicetree/bindings/mfd/cirrus,lochnagar.yaml  | 352 +++++++++++++++++++++
 .../bindings/regulator/cirrus,lochnagar.txt        |  82 -----
 MAINTAINERS                                        |  11 +-
 4 files changed, 357 insertions(+), 173 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt
 create mode 100644 Documentation/devicetree/bindings/mfd/cirrus,lochnagar.yaml
 delete mode 100644 Documentation/devicetree/bindings/regulator/cirrus,lochnagar.txt

Applied, thanks!

maintainer Applied
#9 lore raw
In reply to Charles Keepax
Quoted 5 lines · Charles Keepax

---

No changes since v2.

Quoted 9 lines

Thanks,
Charles

 .../devicetree/bindings/hwmon/cirrus,lochnagar.txt | 26 ----------------
 .../bindings/hwmon/cirrus,lochnagar.yaml           | 35 ++++++++++++++++++++++
 2 files changed, 35 insertions(+), 26 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.txt
 create mode 100644 Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.yaml

Applied, thanks!