Skip to contentSkip to conversation

ARM: dts: stm32: Add GPIO keys for STM32MP1 DHCOM PDK2

PATCH Superseded Marek Vasut 1 participant 4 messages May 12, 2020

Subsystems (4)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/4 ARM: dts: stm32: Add GPIO keys for STM32MP1 DHCOM PDK2

Add bindings for the four GPIO keys on DH PDK2 board. Note that TA1 key is polled because it's IRQ line conflicts with ethernet IRQ, the rest of the GPIO keys, TA2, TA3, TA4, are interrupt-driven and wake up sources.

Cc Alexandre Torgue <[email protected]>
Cc Maxime Coquelin <[email protected]>
Cc Patrice Chotard <[email protected]>
Cc Patrick Delaunay <[email protected]>

To: [email protected]
---
V2: No change

---
 arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts | 43 ++++++++++++++++++++
 1 file changed, 43 insertions(+)
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts +43 -0
index 13b1586d4a8f..e5036c9b9e92 100644
@@ -4,6 +4,7 @@
  */
 
 #include "stm32mp157c-dhcom-som.dtsi"
+#include <dt-bindings/input/input.h>
 #include <dt-bindings/pwm/pwm.h>
 
 / {
@@ -46,6 +47,48 @@ ethernet_vio: vioregulator {
 		regulator-boot-on;
 	};
 
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#size-cells = <0>;
+		poll-interval = <20>;
+
+		/*
+		 * The EXTi IRQ line 3 is shared with touchscreen and ethernet,
+		 * so mark this as polled GPIO key.
+		 */
+		button-0 {
+			label = "TA1-GPIO-A";
+			linux,code = <KEY_A>;
+			gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#size-cells = <0>;
+
+		button-1 {
+			label = "TA2-GPIO-B";
+			linux,code = <KEY_B>;
+			gpios = <&gpiod 6 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+
+		button-2 {
+			label = "TA3-GPIO-C";
+			linux,code = <KEY_C>;
+			gpios = <&gpioi 11 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+
+		button-3 {
+			label = "TA4-GPIO-D";
+			linux,code = <KEY_D>;
+			gpios = <&gpiod 12 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+	};
+
 	panel {
 		compatible = "edt,etm0700g0edh6";
 		backlight = <&display_bl>;
Signature · 7 lines
2.25.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#1 lore raw

PATCH v2 2/4 ARM: dts: stm32: Add GPIO LEDs for STM32MP1 DHCOM PDK2

Add bindings for the four GPIO LEDs on DH PDK2 board. Note that LED5 GPIO-E may conflict with touchscreen interrupt, hence LED5 must be disabled when using the DH 560-200 display unit with touchscreen.

Cc Alexandre Torgue <[email protected]>
Cc Maxime Coquelin <[email protected]>
Cc Patrice Chotard <[email protected]>
Cc Patrick Delaunay <[email protected]>

To: [email protected]
---
V2: No change

---
 arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts | 28 ++++++++++++++++++++
 1 file changed, 28 insertions(+)
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts +28 -0
index e5036c9b9e92..b380268750f3 100644
@@ -89,6 +89,34 @@ button-3 {
 		};
 	};
 
+	led {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "green:led5";
+			gpios = <&gpiog 2 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-1 {
+			label = "green:led6";
+			gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-2 {
+			label = "green:led7";
+			gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-3 {
+			label = "green:led8";
+			gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
 	panel {
 		compatible = "edt,etm0700g0edh6";
 		backlight = <&display_bl>;
Signature · 7 lines
2.25.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#2 lore raw

PATCH v2 3/4 ARM: dts: stm32: Split SoC-independent parts of DHCOM SOM and PDK2

In reply to Marek Vasut

The DH Electronics PDK2 can be populated with SoM with any STM32MP15xx variant. Split the SoC-independent parts of the SoM and PDK2 into the stm32mp15xx-dhcom-*.dtsi and reduce stm32mp157c-dhcom-*dts* to example of adding STM32MP157C variant of the SoM into a PDK2 carrier board.

Cc Alexandre Torgue <[email protected]>
Cc Maxime Coquelin <[email protected]>
Cc Patrice Chotard <[email protected]>
Cc Patrick Delaunay <[email protected]>

To: [email protected]
---
V2: - Drop the stm32mp157c-dhcom-som.dtsi , as it was just include statements
- Add comment about what SoM+Board combination is currently supported

---
 arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts  | 343 +-----------------
 arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi | 342 +++++++++++++++++
 ...om-som.dtsi => stm32mp15xx-dhcom-som.dtsi} |   5 +-
 3 files changed, 352 insertions(+), 338 deletions(-)
 create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
 rename arch/arm/boot/dts/{stm32mp157c-dhcom-som.dtsi => stm32mp15xx-dhcom-som.dtsi} (98%)
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts +9 -334
index b380268750f3..9885509ba1cb 100644
@@ -1,243 +1,18 @@
 // SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
 /*
- * Copyright (C) 2019 Marek Vasut <[email protected]>
+ * Copyright (C) 2019-2020 Marek Vasut <[email protected]>
  */
+/dts-v1/;
 
-#include "stm32mp157c-dhcom-som.dtsi"
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pwm/pwm.h>
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcom-som.dtsi"
+#include "stm32mp15xx-dhcom-pdk2.dtsi"
 
 / {
-	model = "STMicroelectronics STM32MP157C DHCOM Premium Developer Kit (2)";
-	compatible = "dh,stm32mp157c-dhcom-pdk2", "st,stm32mp157";
-
-	aliases {
-		serial0 = &uart4;
-		serial1 = &usart3;
-		serial2 = &uart8;
-		ethernet0 = &ethernet0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	clk_ext_audio_codec: clock-codec {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <24000000>;
-	};
-
-	display_bl: display-bl {
-		compatible = "pwm-backlight";
-		pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
-		brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>;
-		default-brightness-level = <8>;
-		enable-gpios = <&gpioi 0 GPIO_ACTIVE_HIGH>;
-		status = "okay";
-	};
-
-	ethernet_vio: vioregulator {
-		compatible = "regulator-fixed";
-		regulator-name = "vio";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
-		regulator-always-on;
-		regulator-boot-on;
-	};
-
-	gpio-keys-polled {
-		compatible = "gpio-keys-polled";
-		#size-cells = <0>;
-		poll-interval = <20>;
-
-		/*
-		 * The EXTi IRQ line 3 is shared with touchscreen and ethernet,
-		 * so mark this as polled GPIO key.
-		 */
-		button-0 {
-			label = "TA1-GPIO-A";
-			linux,code = <KEY_A>;
-			gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		#size-cells = <0>;
-
-		button-1 {
-			label = "TA2-GPIO-B";
-			linux,code = <KEY_B>;
-			gpios = <&gpiod 6 GPIO_ACTIVE_LOW>;
-			wakeup-source;
-		};
-
-		button-2 {
-			label = "TA3-GPIO-C";
-			linux,code = <KEY_C>;
-			gpios = <&gpioi 11 GPIO_ACTIVE_LOW>;
-			wakeup-source;
-		};
-
-		button-3 {
-			label = "TA4-GPIO-D";
-			linux,code = <KEY_D>;
-			gpios = <&gpiod 12 GPIO_ACTIVE_LOW>;
-			wakeup-source;
-		};
-	};
-
-	led {
-		compatible = "gpio-leds";
-
-		led-0 {
-			label = "green:led5";
-			gpios = <&gpiog 2 GPIO_ACTIVE_HIGH>;
-			default-state = "off";
-		};
-
-		led-1 {
-			label = "green:led6";
-			gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
-			default-state = "off";
-		};
-
-		led-2 {
-			label = "green:led7";
-			gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>;
-			default-state = "off";
-		};
-
-		led-3 {
-			label = "green:led8";
-			gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>;
-			default-state = "off";
-		};
-	};
-
-	panel {
-		compatible = "edt,etm0700g0edh6";
-		backlight = <&display_bl>;
-
-		port {
-			lcd_panel_in: endpoint {
-				remote-endpoint = <&lcd_display_out>;
-			};
-		};
-	};
-
-	sound {
-		compatible = "audio-graph-card";
-		routing =
-			"MIC_IN", "Capture",
-			"Capture", "Mic Bias",
-			"Playback", "HP_OUT";
-		dais = <&sai2a_port &sai2b_port>;
-		status = "okay";
-	};
-};
-
-&cec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&cec_pins_a>;
-	status = "okay";
-};
-
-&ethernet0 {
-	status = "okay";
-	pinctrl-0 = <&ethernet0_rmii_pins_a>;
-	pinctrl-1 = <&ethernet0_rmii_sleep_pins_a>;
-	pinctrl-names = "default", "sleep";
-	phy-mode = "rmii";
-	max-speed = <100>;
-	phy-handle = <&phy0>;
-	st,eth-ref-clk-sel;
-	phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
-
-	mdio0 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "snps,dwmac-mdio";
-
-		phy0: ethernet-phy@1 {
-			reg = <1>;
-		};
-	};
-};
-
-&i2c2 {	/* Header X22 */
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_a>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/* spare dmas for other usage */
-	/delete-property/dmas;
-	/delete-property/dma-names;
-	status = "okay";
-};
-
-&i2c5 {	/* Header X21 */
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c5_pins_a>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/* spare dmas for other usage */
-	/delete-property/dmas;
-	/delete-property/dma-names;
-
-	sgtl5000: codec@a {
-		compatible = "fsl,sgtl5000";
-		reg = <0x0a>;
-		#sound-dai-cells = <0>;
-		clocks = <&clk_ext_audio_codec>;
-		VDDA-supply = <&v3v3>;
-		VDDIO-supply = <&vdd>;
-
-		sgtl5000_port: port {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			sgtl5000_tx_endpoint: endpoint@0 {
-				reg = <0>;
-				remote-endpoint = <&sai2a_endpoint>;
-				frame-master;
-				bitclock-master;
-			};
-
-			sgtl5000_rx_endpoint: endpoint@1 {
-				reg = <1>;
-				remote-endpoint = <&sai2b_endpoint>;
-				frame-master;
-				bitclock-master;
-			};
-		};
-
-	};
-
-	polytouch@38 {
-		compatible = "edt,edt-ft5x06";
-		reg = <0x38>;
-		interrupt-parent = <&gpiog>;
-		interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
-		linux,wakeup;
-	};
-};
-
-&ltdc {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&ltdc_pins_b>;
-	pinctrl-1 = <&ltdc_sleep_pins_b>;
-	status = "okay";
-
-	port {
-		lcd_display_out: endpoint {
-			remote-endpoint = <&lcd_panel_in>;
-		};
-	};
+	model = "DH Electronics STM32MP157C DHCOM Premium Developer Kit (2)";
+	compatible = "dh,stm32mp157c-dhcom-pdk2", "dh,stm32mp157c-dhcom-som",
+		     "st,stm32mp157";
 };
 
 &m_can1 {
@@ -246,103 +21,3 @@ &m_can1 {
 	pinctrl-1 = <&m_can1_sleep_pins_a>;
 	status = "okay";
 };
-
-&sai2 {
-	clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
-	clock-names = "pclk", "x8k", "x11k";
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sai2a_pins_b &sai2b_pins_b>;
-	pinctrl-1 = <&sai2a_sleep_pins_b &sai2b_sleep_pins_b>;
-	status = "okay";
-
-	sai2a: audio-controller@4400b004 {
-		#clock-cells = <0>;
-		dma-names = "tx";
-		clocks = <&rcc SAI2_K>;
-		clock-names = "sai_ck";
-		status = "okay";
-
-		sai2a_port: port {
-			sai2a_endpoint: endpoint {
-				remote-endpoint = <&sgtl5000_tx_endpoint>;
-				format = "i2s";
-				mclk-fs = <512>;
-				dai-tdm-slot-num = <2>;
-				dai-tdm-slot-width = <16>;
-			};
-		};
-	};
-
-	sai2b: audio-controller@4400b024 {
-		dma-names = "rx";
-		st,sync = <&sai2a 2>;
-		clocks = <&rcc SAI2_K>, <&sai2a>;
-		clock-names = "sai_ck", "MCLK";
-		status = "okay";
-
-		sai2b_port: port {
-			sai2b_endpoint: endpoint {
-				remote-endpoint = <&sgtl5000_rx_endpoint>;
-				format = "i2s";
-				mclk-fs = <512>;
-				dai-tdm-slot-num = <2>;
-				dai-tdm-slot-width = <16>;
-			};
-		};
-	};
-};
-
-&timers2 {
-	/* spare dmas for other usage (un-delete to enable pwm capture) */
-	/delete-property/dmas;
-	/delete-property/dma-names;
-	status = "okay";
-	pwm2: pwm {
-		pinctrl-0 = <&pwm2_pins_a>;
-		pinctrl-names = "default";
-		status = "okay";
-	};
-	timer@1 {
-		status = "okay";
-	};
-};
-
-&usart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usart3_pins_a>;
-	status = "okay";
-};
-
-&uart8 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart8_pins_a>;
-	status = "okay";
-};
-
-&usbh_ehci {
-	phys = <&usbphyc_port0>;
-	status = "okay";
-};
-
-&usbotg_hs {
-	dr_mode = "peripheral";
-	phys = <&usbphyc_port1 0>;
-	phy-names = "usb2-phy";
-	status = "okay";
-};
-
-&usbphyc {
-	status = "okay";
-};
-
-&usbphyc_port0 {
-	phy-supply = <&vdd_usb>;
-	vdda1v1-supply = <&reg11>;
-	vdda1v8-supply = <&reg18>;
-};
-
-&usbphyc_port1 {
-	phy-supply = <&vdd_usb>;
-	vdda1v1-supply = <&reg11>;
-	vdda1v8-supply = <&reg18>;
-};
arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi new file +342 -0

342 lines not on this page · raw message

arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi renamed from arch/arm/boot/dts/stm32mp157c-dhcom-som.dtsi +1 -4
similarity index 98%
rename from arch/arm/boot/dts/stm32mp157c-dhcom-som.dtsi
rename to arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
index f97e0d2ecf17..ba905196fb54 100644
@@ -1,11 +1,8 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
 /*
- * Copyright (C) 2019 Marek Vasut <[email protected]>
+ * Copyright (C) 2019-2020 Marek Vasut <[email protected]>
  */
-/dts-v1/;
 
-#include "stm32mp157.dtsi"
-#include "stm32mp15xc.dtsi"
 #include "stm32mp15-pinctrl.dtsi"
 #include "stm32mp15xxaa-pinctrl.dtsi"
 #include <dt-bindings/gpio/gpio.h>
Signature · 7 lines
2.25.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#3 lore raw

PATCH v2 4/4 ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board

In reply to Marek Vasut

The Avenger96 is in fact an assembly of DH Electronics DHCOR SoM on top of an Avenger96 reference board. The DHCOR SoM can be populated with any STM32MP15xx. Split the DTs to reflect this such that the common SoM and Avenger96 parts are now in stm32mp15xx-dhcor-*dtsi and a specific example implementation of STM32MP157A SoM and Avenger96 board is separated into stm32mp157a-dhcor-*dts* . The stm32mp157a-avenger96.dts is retained for the sake of backward naming compatibility.

Cc Alexandre Torgue <[email protected]>
Cc Manivannan Sadhasivam <[email protected]>
Cc Maxime Coquelin <[email protected]>
Cc Patrice Chotard <[email protected]>
Cc Patrick Delaunay <[email protected]>

To: [email protected]
---
V2: - Drop the stm32mp157a-dhcor-som.dtsi , as it was just include statements
- Add comment about what SoM+Board combination is currently supported

---
 arch/arm/boot/dts/Makefile                    |   1 +
 arch/arm/boot/dts/stm32mp157a-avenger96.dts   | 618 +-----------------
 .../boot/dts/stm32mp157a-dhcor-avenger96.dts  |  38 ++
 .../boot/dts/stm32mp15xx-dhcor-avenger96.dtsi | 401 ++++++++++++
 .../arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi |  23 +
 arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi  | 209 ++++++
 6 files changed, 675 insertions(+), 615 deletions(-)
 create mode 100644 arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts
 create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
 create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi
 create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
arch/arm/boot/dts/Makefile +1 -0
index f43467b02bcd..d0f6c5838568 100644
@@ -1029,6 +1029,7 @@ dtb-$(CONFIG_ARCH_STM32) += \
 	stm32h743i-eval.dtb \
 	stm32h743i-disco.dtb \
 	stm32mp157a-avenger96.dtb \
+	stm32mp157a-dhcor-avenger96.dtb \
 	stm32mp157a-dk1.dtb \
 	stm32mp157c-dhcom-pdk2.dtb \
 	stm32mp157c-dk2.dtb \
arch/arm/boot/dts/stm32mp157a-avenger96.dts +3 -615

625 lines not on this page · raw message

arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts new file +38 -0
new file mode 100644
index 000000000000..2e3c9fbb4eb3
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <[email protected]>
+ * Copyright (C) 2020 Marek Vasut <[email protected]>
+ *
+ * DHCOR STM32MP1 variant:
+ * DHCR-STM32MP157A-C065-R102-V18-SPI-C-01LG
+ * DHCOR PCB number: 586-100 or newer
+ * Avenger96 PCB number: 588-200 or newer
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcor-som.dtsi"
+#include "stm32mp15xx-dhcor-avenger96.dtsi"
+
+/ {
+	model = "Arrow Electronics STM32MP157A Avenger96 board";
+	compatible = "arrow,stm32mp157a-avenger96", "dh,stm32mp157a-dhcor-som",
+		     "st,stm32mp157";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_b>;
+	pinctrl-1 = <&m_can1_sleep_pins_b>;
+	status = "disabled";
+};
+
+&m_can2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can2_pins_a>;
+	pinctrl-1 = <&m_can2_sleep_pins_a>;
+	status = "disabled";
+};
arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi new file +401 -0

401 lines not on this page · raw message

arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi new file +23 -0
new file mode 100644
index 000000000000..75172314d7af
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <[email protected]>
+ * Copyright (C) 2020 Marek Vasut <[email protected]>
+ */
+
+/ {
+	/* Enpirion EP3A8LQI U2 on the DHCOR */
+	vdd_io: regulator-buck-io {
+		compatible = "regulator-fixed";
+		regulator-name = "buck-io";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd>;
+	};
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd_io>;
+};
arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi new file +209 -0

209 lines not on this page · raw message

Signature · 7 lines
2.25.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel