ARM: dts: stm32: Add GPIO keys for STM32MP1 DHCOM PDK2
Subsystems (4)
PATCH v3 1/4 ARM: dts: stm32: Add GPIO keys for STM32MP1 DHCOM PDK2
Add bindings for the four GPIO keys on DH PDK2 board. Note that TA1 key is polled because it's IRQ line conflicts with ethernet IRQ, the rest of the GPIO keys, TA2, TA3, TA4, are interrupt-driven and wake up sources.
To: [email protected]
---
V2: No change
V3: No change
--- arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts | 43 ++++++++++++++++++++ 1 file changed, 43 insertions(+)
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts +43 -0
@@ -4,6 +4,7 @@ */ #include "stm32mp157c-dhcom-som.dtsi" +#include <dt-bindings/input/input.h> #include <dt-bindings/pwm/pwm.h> / {
@@ -46,6 +47,48 @@ ethernet_vio: vioregulator { regulator-boot-on; }; + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #size-cells = <0>; + poll-interval = <20>; + + /* + * The EXTi IRQ line 3 is shared with touchscreen and ethernet, + * so mark this as polled GPIO key. + */ + button-0 { + label = "TA1-GPIO-A"; + linux,code = <KEY_A>; + gpios = <&gpiof 3 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + #size-cells = <0>; + + button-1 { + label = "TA2-GPIO-B"; + linux,code = <KEY_B>; + gpios = <&gpiod 6 GPIO_ACTIVE_LOW>; + wakeup-source; + }; + + button-2 { + label = "TA3-GPIO-C"; + linux,code = <KEY_C>; + gpios = <&gpioi 11 GPIO_ACTIVE_LOW>; + wakeup-source; + }; + + button-3 { + label = "TA4-GPIO-D"; + linux,code = <KEY_D>; + gpios = <&gpiod 12 GPIO_ACTIVE_LOW>; + wakeup-source; + }; + }; + panel { compatible = "edt,etm0700g0edh6"; backlight = <&display_bl>;
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v3 2/4 ARM: dts: stm32: Add GPIO LEDs for STM32MP1 DHCOM PDK2
Add bindings for the four GPIO LEDs on DH PDK2 board. Note that LED5 GPIO-E may conflict with touchscreen interrupt, hence LED5 must be disabled when using the DH 560-200 display unit with touchscreen.
To: [email protected]
---
V2: No change
V3: No change
--- arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts | 28 ++++++++++++++++++++ 1 file changed, 28 insertions(+)
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts +28 -0
@@ -89,6 +89,34 @@ button-3 { }; }; + led { + compatible = "gpio-leds"; + + led-0 { + label = "green:led5"; + gpios = <&gpiog 2 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-1 { + label = "green:led6"; + gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-2 { + label = "green:led7"; + gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-3 { + label = "green:led8"; + gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + panel { compatible = "edt,etm0700g0edh6"; backlight = <&display_bl>;
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v3 3/4 ARM: dts: stm32: Split SoC-independent parts of DHCOM SOM and PDK2
In reply to Marek VasutThe DH Electronics PDK2 can be populated with SoM with any STM32MP15xx variant. Split the SoC-independent parts of the SoM and PDK2 into the stm32mp15xx-dhcom-*.dtsi and reduce stm32mp157c-dhcom-*dts* to example of adding STM32MP157C variant of the SoM into a PDK2 carrier board.
To: [email protected]
---
V2: - Drop the stm32mp157c-dhcom-som.dtsi , as it was just include statements
- Add comment about what SoM+Board combination is currently supported
V3: Move the comment to stm32mp157c-dhcom-pdk2.dts
---
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts | 348 +-----------------
arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi | 337 +++++++++++++++++
...om-som.dtsi => stm32mp15xx-dhcom-som.dtsi} | 5 +-
3 files changed, 352 insertions(+), 338 deletions(-)
create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
rename arch/arm/boot/dts/{stm32mp157c-dhcom-som.dtsi => stm32mp15xx-dhcom-som.dtsi} (98%)arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts +14 -334
@@ -1,243 +1,23 @@ // SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause /* - * Copyright (C) 2019 Marek Vasut <[email protected]> + * Copyright (C) 2019-2020 Marek Vasut <[email protected]> + * + * DHCOM STM32MP1 variant: + * DHCM-STM32MP157C-C065-R102-F0819-SPI-E2-CAN2-SDR104-RTC-WBT-T-DSI-I-01D2 + * DHCOR PCB number: 587-200 or newer + * PDK2 PCB number: 516-400 or newer */ +/dts-v1/; -#include "stm32mp157c-dhcom-som.dtsi" -#include <dt-bindings/input/input.h> -#include <dt-bindings/pwm/pwm.h> +#include "stm32mp157.dtsi" +#include "stm32mp15xc.dtsi" +#include "stm32mp15xx-dhcom-som.dtsi" +#include "stm32mp15xx-dhcom-pdk2.dtsi" / { - model = "STMicroelectronics STM32MP157C DHCOM Premium Developer Kit (2)"; - compatible = "dh,stm32mp157c-dhcom-pdk2", "st,stm32mp157"; - - aliases { - serial0 = &uart4; - serial1 = &usart3; - serial2 = &uart8; - ethernet0 = ðernet0; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - clk_ext_audio_codec: clock-codec { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <24000000>; - }; - - display_bl: display-bl { - compatible = "pwm-backlight"; - pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>; - brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>; - default-brightness-level = <8>; - enable-gpios = <&gpioi 0 GPIO_ACTIVE_HIGH>; - status = "okay"; - }; - - ethernet_vio: vioregulator { - compatible = "regulator-fixed"; - regulator-name = "vio"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpiog 3 GPIO_ACTIVE_LOW>; - regulator-always-on; - regulator-boot-on; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #size-cells = <0>; - poll-interval = <20>; - - /* - * The EXTi IRQ line 3 is shared with touchscreen and ethernet, - * so mark this as polled GPIO key. - */ - button-0 { - label = "TA1-GPIO-A"; - linux,code = <KEY_A>; - gpios = <&gpiof 3 GPIO_ACTIVE_LOW>; - }; - }; - - gpio-keys { - compatible = "gpio-keys"; - #size-cells = <0>; - - button-1 { - label = "TA2-GPIO-B"; - linux,code = <KEY_B>; - gpios = <&gpiod 6 GPIO_ACTIVE_LOW>; - wakeup-source; - }; - - button-2 { - label = "TA3-GPIO-C"; - linux,code = <KEY_C>; - gpios = <&gpioi 11 GPIO_ACTIVE_LOW>; - wakeup-source; - }; - - button-3 { - label = "TA4-GPIO-D"; - linux,code = <KEY_D>; - gpios = <&gpiod 12 GPIO_ACTIVE_LOW>; - wakeup-source; - }; - }; - - led { - compatible = "gpio-leds"; - - led-0 { - label = "green:led5"; - gpios = <&gpiog 2 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - - led-1 { - label = "green:led6"; - gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - - led-2 { - label = "green:led7"; - gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - - led-3 { - label = "green:led8"; - gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - }; - - panel { - compatible = "edt,etm0700g0edh6"; - backlight = <&display_bl>; - - port { - lcd_panel_in: endpoint { - remote-endpoint = <&lcd_display_out>; - }; - }; - }; - - sound { - compatible = "audio-graph-card"; - routing = - "MIC_IN", "Capture", - "Capture", "Mic Bias", - "Playback", "HP_OUT"; - dais = <&sai2a_port &sai2b_port>; - status = "okay"; - }; -}; - -&cec { - pinctrl-names = "default"; - pinctrl-0 = <&cec_pins_a>; - status = "okay"; -}; - -ðernet0 { - status = "okay"; - pinctrl-0 = <ðernet0_rmii_pins_a>; - pinctrl-1 = <ðernet0_rmii_sleep_pins_a>; - pinctrl-names = "default", "sleep"; - phy-mode = "rmii"; - max-speed = <100>; - phy-handle = <&phy0>; - st,eth-ref-clk-sel; - phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>; - - mdio0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "snps,dwmac-mdio"; - - phy0: ethernet-phy@1 { - reg = <1>; - }; - }; -}; - -&i2c2 { /* Header X22 */ - pinctrl-names = "default"; - pinctrl-0 = <&i2c2_pins_a>; - i2c-scl-rising-time-ns = <185>; - i2c-scl-falling-time-ns = <20>; - status = "okay"; - /* spare dmas for other usage */ - /delete-property/dmas; - /delete-property/dma-names; - status = "okay"; -}; - -&i2c5 { /* Header X21 */ - pinctrl-names = "default"; - pinctrl-0 = <&i2c5_pins_a>; - i2c-scl-rising-time-ns = <185>; - i2c-scl-falling-time-ns = <20>; - status = "okay"; - /* spare dmas for other usage */ - /delete-property/dmas; - /delete-property/dma-names; - - sgtl5000: codec@a { - compatible = "fsl,sgtl5000"; - reg = <0x0a>; - #sound-dai-cells = <0>; - clocks = <&clk_ext_audio_codec>; - VDDA-supply = <&v3v3>; - VDDIO-supply = <&vdd>; - - sgtl5000_port: port { - #address-cells = <1>; - #size-cells = <0>; - - sgtl5000_tx_endpoint: endpoint@0 { - reg = <0>; - remote-endpoint = <&sai2a_endpoint>; - frame-master; - bitclock-master; - }; - - sgtl5000_rx_endpoint: endpoint@1 { - reg = <1>; - remote-endpoint = <&sai2b_endpoint>; - frame-master; - bitclock-master; - }; - }; - - }; - - polytouch@38 { - compatible = "edt,edt-ft5x06"; - reg = <0x38>; - interrupt-parent = <&gpiog>; - interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */ - linux,wakeup; - }; -}; - -<dc { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <<dc_pins_b>; - pinctrl-1 = <<dc_sleep_pins_b>; - status = "okay"; - - port { - lcd_display_out: endpoint { - remote-endpoint = <&lcd_panel_in>; - }; - }; + model = "DH Electronics STM32MP157C DHCOM Premium Developer Kit (2)"; + compatible = "dh,stm32mp157c-dhcom-pdk2", "dh,stm32mp157c-dhcom-som", + "st,stm32mp157"; }; &m_can1 {
@@ -246,103 +26,3 @@ &m_can1 { pinctrl-1 = <&m_can1_sleep_pins_a>; status = "okay"; }; - -&sai2 { - clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>; - clock-names = "pclk", "x8k", "x11k"; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&sai2a_pins_b &sai2b_pins_b>; - pinctrl-1 = <&sai2a_sleep_pins_b &sai2b_sleep_pins_b>; - status = "okay"; - - sai2a: audio-controller@4400b004 { - #clock-cells = <0>; - dma-names = "tx"; - clocks = <&rcc SAI2_K>; - clock-names = "sai_ck"; - status = "okay"; - - sai2a_port: port { - sai2a_endpoint: endpoint { - remote-endpoint = <&sgtl5000_tx_endpoint>; - format = "i2s"; - mclk-fs = <512>; - dai-tdm-slot-num = <2>; - dai-tdm-slot-width = <16>; - }; - }; - }; - - sai2b: audio-controller@4400b024 { - dma-names = "rx"; - st,sync = <&sai2a 2>; - clocks = <&rcc SAI2_K>, <&sai2a>; - clock-names = "sai_ck", "MCLK"; - status = "okay"; - - sai2b_port: port { - sai2b_endpoint: endpoint { - remote-endpoint = <&sgtl5000_rx_endpoint>; - format = "i2s"; - mclk-fs = <512>; - dai-tdm-slot-num = <2>; - dai-tdm-slot-width = <16>; - }; - }; - }; -}; - -&timers2 { - /* spare dmas for other usage (un-delete to enable pwm capture) */ - /delete-property/dmas; - /delete-property/dma-names; - status = "okay"; - pwm2: pwm { - pinctrl-0 = <&pwm2_pins_a>; - pinctrl-names = "default"; - status = "okay"; - }; - timer@1 { - status = "okay"; - }; -}; - -&usart3 { - pinctrl-names = "default"; - pinctrl-0 = <&usart3_pins_a>; - status = "okay"; -}; - -&uart8 { - pinctrl-names = "default"; - pinctrl-0 = <&uart8_pins_a>; - status = "okay"; -}; - -&usbh_ehci { - phys = <&usbphyc_port0>; - status = "okay"; -}; - -&usbotg_hs { - dr_mode = "peripheral"; - phys = <&usbphyc_port1 0>; - phy-names = "usb2-phy"; - status = "okay"; -}; - -&usbphyc { - status = "okay"; -}; - -&usbphyc_port0 { - phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; -}; - -&usbphyc_port1 { - phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; -};
arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi new file +337 -0
337 lines not on this page · raw message
arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi renamed from arch/arm/boot/dts/stm32mp157c-dhcom-som.dtsi +1 -4
@@ -1,11 +1,8 @@ // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) /* - * Copyright (C) 2019 Marek Vasut <[email protected]> + * Copyright (C) 2019-2020 Marek Vasut <[email protected]> */ -/dts-v1/; -#include "stm32mp157.dtsi" -#include "stm32mp15xc.dtsi" #include "stm32mp15-pinctrl.dtsi" #include "stm32mp15xxaa-pinctrl.dtsi" #include <dt-bindings/gpio/gpio.h>
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v3 4/4 ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board
In reply to Marek VasutThe Avenger96 is in fact an assembly of DH Electronics DHCOR SoM on top of an Avenger96 reference board. The DHCOR SoM can be populated with any STM32MP15xx. Split the DTs to reflect this such that the common SoM and Avenger96 parts are now in stm32mp15xx-dhcor-*dtsi and a specific example implementation of STM32MP157A SoM and Avenger96 board is separated into stm32mp157a-dhcor-*dts* . The stm32mp157a-avenger96.dts is retained for the sake of backward naming compatibility.
To: [email protected]
---
V2: - Drop the stm32mp157a-dhcor-som.dtsi , as it was just include statements
- Add comment about what SoM+Board combination is currently supported
V3: No change
--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/stm32mp157a-avenger96.dts | 618 +----------------- .../boot/dts/stm32mp157a-dhcor-avenger96.dts | 38 ++ .../boot/dts/stm32mp15xx-dhcor-avenger96.dtsi | 401 ++++++++++++ .../arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi | 23 + arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi | 209 ++++++ 6 files changed, 675 insertions(+), 615 deletions(-) create mode 100644 arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
arch/arm/boot/dts/Makefile +1 -0
@@ -1029,6 +1029,7 @@ dtb-$(CONFIG_ARCH_STM32) += \ stm32h743i-eval.dtb \ stm32h743i-disco.dtb \ stm32mp157a-avenger96.dtb \ + stm32mp157a-dhcor-avenger96.dtb \ stm32mp157a-dk1.dtb \ stm32mp157c-dhcom-pdk2.dtb \ stm32mp157c-dk2.dtb \
arch/arm/boot/dts/stm32mp157a-avenger96.dts +3 -615
625 lines not on this page · raw message
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts new file +38 -0
@@ -0,0 +1,38 @@ +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) +/* + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved + * Author: Manivannan Sadhasivam <[email protected]> + * Copyright (C) 2020 Marek Vasut <[email protected]> + * + * DHCOR STM32MP1 variant: + * DHCR-STM32MP157A-C065-R102-V18-SPI-C-01LG + * DHCOR PCB number: 586-100 or newer + * Avenger96 PCB number: 588-200 or newer + */ + +/dts-v1/; + +#include "stm32mp157.dtsi" +#include "stm32mp15xc.dtsi" +#include "stm32mp15xx-dhcor-som.dtsi" +#include "stm32mp15xx-dhcor-avenger96.dtsi" + +/ { + model = "Arrow Electronics STM32MP157A Avenger96 board"; + compatible = "arrow,stm32mp157a-avenger96", "dh,stm32mp157a-dhcor-som", + "st,stm32mp157"; +}; + +&m_can1 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&m_can1_pins_b>; + pinctrl-1 = <&m_can1_sleep_pins_b>; + status = "disabled"; +}; + +&m_can2 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&m_can2_pins_a>; + pinctrl-1 = <&m_can2_sleep_pins_a>; + status = "disabled"; +};
arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi new file +401 -0
401 lines not on this page · raw message
arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi new file +23 -0
@@ -0,0 +1,23 @@ +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) +/* + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved + * Author: Manivannan Sadhasivam <[email protected]> + * Copyright (C) 2020 Marek Vasut <[email protected]> + */ + +/ { + /* Enpirion EP3A8LQI U2 on the DHCOR */ + vdd_io: regulator-buck-io { + compatible = "regulator-fixed"; + regulator-name = "buck-io"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vdd>; + }; +}; + +&pwr_regulators { + vdd-supply = <&vdd_io>; +};
arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi new file +209 -0
209 lines not on this page · raw message
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Re: [PATCH V3 4/4] ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board
Quoted 9 lines · Marek Vasut
The Avenger96 is in fact an assembly of DH Electronics DHCOR SoM on top of an Avenger96 reference board. The DHCOR SoM can be populated with any STM32MP15xx. Split the DTs to reflect this such that the common SoM and Avenger96 parts are now in stm32mp15xx-dhcor-*dtsi and a specific example implementation of STM32MP157A SoM and Avenger96 board is separated into stm32mp157a-dhcor-*dts* . The
stm32mp157a-avenger96.dtsis retained for the sake of backward naming compatibility.Signed-off-by Marek Vasut <[email protected]>
LGTM.
Thanks,
Mani
Quoted 1,364 lines
Cc: Alexandre Torgue <[email protected]>
Cc: Manivannan Sadhasivam <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Cc: [email protected]
To: [email protected]
---
V2: - Drop thestm32mp157a-dhcor-som.dtsi, as it was just include statements
- Add comment about what SoM+Board combination is currently supported
V3: No change--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/stm32mp157a-avenger96.dts | 618 +----------------- .../boot/dts/stm32mp157a-dhcor-avenger96.dts | 38 ++ .../boot/dts/stm32mp15xx-dhcor-avenger96.dtsi | 401 ++++++++++++ .../arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi | 23 + arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi | 209 ++++++ 6 files changed, 675 insertions(+), 615 deletions(-) create mode 100644 arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsiarch/arm/boot/dts/Makefile +1
-0@@ -1029,6 +1029,7 @@ dtb-$(CONFIG_ARCH_STM32) += \ stm32h743i-eval.dtb \ stm32h743i-disco.dtb \ stm32mp157a-avenger96.dtb \ + stm32mp157a-dhcor-avenger96.dtb \ stm32mp157a-dk1.dtb \ stm32mp157c-dhcom-pdk2.dtb \ stm32mp157c-dk2.dtb \arch/arm/boot/dts/stm32mp157a-avenger96.dts +3
-615@@ -2,622 +2,10 @@ /* * Copyright (C) Linaro Ltd 2019 - All Rights Reserved * Author: Manivannan Sadhasivam <[email protected]> + * Copyright (C) 2020 Marek Vasut <[email protected]> */ /dts-v1/; -#include "stm32mp157.dtsi" -#include "stm32mp15-pinctrl.dtsi" -#include "stm32mp15xxac-pinctrl.dtsi" -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/mfd/st,stpmic1.h> - -/ { - model = "Arrow Electronics STM32MP157A Avenger96 board"; - compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157"; - - aliases { - ethernet0 = ðernet0; - mmc0 = &sdmmc1; - serial0 = &uart4; - serial1 = &uart7; - serial2 = &usart2; - spi0 = &qspi; - }; - - /* XTal Q1 */ - cec_clock: clk-cec-fixed { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <24000000>; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - hdmi-out { - compatible = "hdmi-connector"; - type = "a"; - - port { - hdmi_con: endpoint { - remote-endpoint = <&adv7513_out>; - }; - }; - }; - - memory@c0000000 { - device_type = "memory"; - reg = <0xc0000000 0x40000000>; - }; - - led { - compatible = "gpio-leds"; - led1 { - label = "green:user0"; - gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "heartbeat"; - default-state = "off"; - }; - - led2 { - label = "green:user1"; - gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "mmc0"; - default-state = "off"; - }; - - led3 { - label = "green:user2"; - gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "mmc1"; - default-state = "off"; - }; - - led4 { - label = "green:user3"; - gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "none"; - default-state = "off"; - panic-indicator; - }; - }; - - sd_switch: regulator-sd_switch { - compatible = "regulator-gpio"; - regulator-name = "sd_switch"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <2900000>; - regulator-type = "voltage"; - regulator-always-on; - - gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>; - gpios-states = <0>; - states = <1800000 0x1>, - <2900000 0x0>; - }; - - sound { - compatible = "audio-graph-card"; - label = "STM32MP1-AV96-HDMI"; - dais = <&sai2a_port>; - status = "okay"; - }; - - /* Enpirion EP3A8LQI U2 on the DHCOR */ - vdd_io: regulator-buck-io { - compatible = "regulator-fixed"; - regulator-name = "buck-io"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - vin-supply = <&vdd>; - }; - - wlan_pwr: regulator-wlan { - compatible = "regulator-fixed"; - - regulator-name = "wl-reg"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - - gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -&adc { - pinctrl-names = "default"; - pinctrl-0 = <&adc12_ain_pins_b>; - vdd-supply = <&vdd>; - vdda-supply = <&vdda>; - vref-supply = <&vdda>; - status = "okay"; - - adc1: adc@0 { - st,adc-channels = <0 1 6>; - st,min-sample-time-nsecs = <5000>; - status = "okay"; - }; - - adc2: adc@100 { - st,adc-channels = <0 1 2>; - st,min-sample-time-nsecs = <5000>; - status = "okay"; - }; -}; - -ðernet0 { - status = "okay"; - pinctrl-0 = <ðernet0_rgmii_pins_c>; - pinctrl-1 = <ðernet0_rgmii_sleep_pins_c>; - pinctrl-names = "default", "sleep"; - phy-mode = "rgmii"; - max-speed = <1000>; - phy-handle = <&phy0>; - - mdio0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "snps,dwmac-mdio"; - reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>; - reset-delay-us = <1000>; - - phy0: ethernet-phy@7 { - reg = <7>; - - rxc-skew-ps = <1500>; - rxdv-skew-ps = <540>; - rxd0-skew-ps = <420>; - rxd1-skew-ps = <420>; - rxd2-skew-ps = <420>; - rxd3-skew-ps = <420>; - - txc-skew-ps = <1440>; - txen-skew-ps = <540>; - txd0-skew-ps = <420>; - txd1-skew-ps = <420>; - txd2-skew-ps = <420>; - txd3-skew-ps = <420>; - }; - }; -}; - -&i2c1 { /* X6 I2C1 */ - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_pins_b>; - i2c-scl-rising-time-ns = <185>; - i2c-scl-falling-time-ns = <20>; - status = "okay"; - /delete-property/dmas; - /delete-property/dma-names; -}; - -&i2c2 { /* X6 I2C2 */ - pinctrl-names = "default"; - pinctrl-0 = <&i2c2_pins_c>; - i2c-scl-rising-time-ns = <185>; - i2c-scl-falling-time-ns = <20>; - status = "okay"; - /delete-property/dmas; - /delete-property/dma-names; -}; - -&i2c4 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c4_pins_a>; - i2c-scl-rising-time-ns = <185>; - i2c-scl-falling-time-ns = <20>; - status = "okay"; - /delete-property/dmas; - /delete-property/dma-names; - - pmic: stpmic@33 { - compatible = "st,stpmic1"; - reg = <0x33>; - interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>; - interrupt-controller; - #interrupt-cells = <2>; - status = "okay"; - - regulators { - compatible = "st,stpmic1-regulators"; - - ldo1-supply = <&v3v3>; - ldo2-supply = <&v3v3>; - ldo3-supply = <&vdd_ddr>; - ldo5-supply = <&v3v3>; - ldo6-supply = <&v3v3>; - pwr_sw1-supply = <&bst_out>; - pwr_sw2-supply = <&bst_out>; - - vddcore: buck1 { - regulator-name = "vddcore"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-initial-mode = <0>; - regulator-over-current-protection; - }; - - vdd_ddr: buck2 { - regulator-name = "vdd_ddr"; - regulator-min-microvolt = <1350000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-initial-mode = <0>; - regulator-over-current-protection; - }; - - vdd: buck3 { - regulator-name = "vdd"; - regulator-min-microvolt = <2900000>; - regulator-max-microvolt = <2900000>; - regulator-always-on; - regulator-initial-mode = <0>; - regulator-over-current-protection; - }; - - v3v3: buck4 { - regulator-name = "v3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-over-current-protection; - regulator-initial-mode = <0>; - }; - - vdda: ldo1 { - regulator-name = "vdda"; - regulator-min-microvolt = <2900000>; - regulator-max-microvolt = <2900000>; - interrupts = <IT_CURLIM_LDO1 0>; - }; - - v2v8: ldo2 { - regulator-name = "v2v8"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - interrupts = <IT_CURLIM_LDO2 0>; - }; - - vtt_ddr: ldo3 { - regulator-name = "vtt_ddr"; - regulator-min-microvolt = <500000>; - regulator-max-microvolt = <750000>; - regulator-always-on; - regulator-over-current-protection; - }; - - vdd_usb: ldo4 { - regulator-name = "vdd_usb"; - interrupts = <IT_CURLIM_LDO4 0>; - }; - - vdd_sd: ldo5 { - regulator-name = "vdd_sd"; - regulator-min-microvolt = <2900000>; - regulator-max-microvolt = <2900000>; - interrupts = <IT_CURLIM_LDO5 0>; - regulator-boot-on; - }; - - v1v8: ldo6 { - regulator-name = "v1v8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - interrupts = <IT_CURLIM_LDO6 0>; - regulator-enable-ramp-delay = <300000>; - }; - - vref_ddr: vref_ddr { - regulator-name = "vref_ddr"; - regulator-always-on; - }; - - bst_out: boost { - regulator-name = "bst_out"; - interrupts = <IT_OCP_BOOST 0>; - }; - - vbus_otg: pwr_sw1 { - regulator-name = "vbus_otg"; - interrupts = <IT_OCP_OTG 0>; - regulator-active-discharge = <1>; - }; - - vbus_sw: pwr_sw2 { - regulator-name = "vbus_sw"; - interrupts = <IT_OCP_SWOUT 0>; - regulator-active-discharge = <1>; - }; - }; - - onkey { - compatible = "st,stpmic1-onkey"; - interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>; - interrupt-names = "onkey-falling", "onkey-rising"; - status = "okay"; - }; - - watchdog { - compatible = "st,stpmic1-wdt"; - status = "disabled"; - }; - }; - - hdmi-transmitter@3d { - compatible = "adi,adv7513"; - reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>; - reg-names = "main", "cec", "edid", "packet"; - clocks = <&cec_clock>; - clock-names = "cec"; - - avdd-supply = <&v3v3>; - dvdd-supply = <&v3v3>; - pvdd-supply = <&v3v3>; - dvdd-3v-supply = <&v3v3>; - bgvdd-supply = <&v3v3>; - - interrupts = <9 IRQ_TYPE_EDGE_FALLING>; - interrupt-parent = <&gpiog>; - - status = "okay"; - - adi,input-depth = <8>; - adi,input-colorspace = "rgb"; - adi,input-clock = "1x"; - adi,input-style = <1>; - adi,input-justification = "evenly"; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - adv7513_in: endpoint { - remote-endpoint = <<dc_ep0_out>; - }; - }; - - port@1 { - reg = <1>; - adv7513_out: endpoint { - remote-endpoint = <&hdmi_con>; - }; - }; - - port@2 { - reg = <2>; - adv7513_i2s0: endpoint { - remote-endpoint = <&sai2a_endpoint>; - }; - }; - }; - }; - - eeprom@53 { - compatible = "atmel,24c02"; - reg = <0x53>; - pagesize = <16>; - }; -}; - -&iwdg2 { - timeout-sec = <32>; - status = "okay"; -}; - -<dc { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <<dc_pins_d>; - pinctrl-1 = <<dc_sleep_pins_d>; - status = "okay"; - - port { - #address-cells = <1>; - #size-cells = <0>; - - ltdc_ep0_out: endpoint@0 { - reg = <0>; - remote-endpoint = <&adv7513_in>; - }; - }; -}; - -&m_can1 { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&m_can1_pins_b>; - pinctrl-1 = <&m_can1_sleep_pins_b>; - status = "disabled"; -}; - -&m_can2 { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&m_can2_pins_a>; - pinctrl-1 = <&m_can2_sleep_pins_a>; - status = "disabled"; -}; - -&pwr_regulators { - vdd-supply = <&vdd_io>; - vdd_3v3_usbfs-supply = <&vdd_usb>; -}; - -&qspi { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>; - pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>; - reg = <0x58003000 0x1000>, <0x70000000 0x200000>; - #address-cells = <1>; - #size-cells = <0>; - status = "okay"; - - flash0: spi-flash@0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-rx-bus-width = <4>; - spi-max-frequency = <108000000>; - #address-cells = <1>; - #size-cells = <1>; - }; -}; - -&rng1 { - status = "okay"; -}; - -&rtc { - status = "okay"; -}; - -&sai2 { - clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&sai2a_pins_c>; - pinctrl-1 = <&sai2a_sleep_pins_c>; - clock-names = "pclk", "x8k", "x11k"; - status = "okay"; - - sai2a: audio-controller@4400b004 { - #clock-cells = <0>; - dma-names = "tx"; - clocks = <&rcc SAI2_K>; - clock-names = "sai_ck"; - status = "okay"; - - sai2a_port: port { - sai2a_endpoint: endpoint { - remote-endpoint = <&adv7513_i2s0>; - format = "i2s"; - mclk-fs = <256>; - }; - }; - }; -}; - -&sdmmc1 { - pinctrl-names = "default", "opendrain", "sleep"; - pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>; - pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>; - pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>; - cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; - disable-wp; - st,sig-dir; - st,neg-edge; - st,use-ckin; - bus-width = <4>; - vmmc-supply = <&vdd_sd>; - vqmmc-supply = <&sd_switch>; - status = "okay"; -}; - -&sdmmc2 { - pinctrl-names = "default", "opendrain", "sleep"; - pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>; - pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>; - pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>; - bus-width = <8>; - mmc-ddr-1_8v; - no-sd; - no-sdio; - non-removable; - st,neg-edge; - vmmc-supply = <&v3v3>; - vqmmc-supply = <&vdd_io>; - status = "okay"; -}; - -&sdmmc3 { - pinctrl-names = "default", "opendrain", "sleep"; - pinctrl-0 = <&sdmmc3_b4_pins_b>; - pinctrl-1 = <&sdmmc3_b4_od_pins_b>; - pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>; - broken-cd; - non-removable; - st,neg-edge; - bus-width = <4>; - vmmc-supply = <&wlan_pwr>; - status = "okay"; - - #address-cells = <1>; - #size-cells = <0>; - brcmf: bcrmf@1 { - reg = <1>; - compatible = "brcm,bcm4329-fmac"; - }; -}; - -&spi2 { - pinctrl-names = "default"; - pinctrl-0 = <&spi2_pins_a>; - cs-gpios = <&gpioi 0 0>; - status = "disabled"; - /delete-property/dmas; - /delete-property/dma-names; -}; - -&uart4 { - /* On Low speed expansion header */ - label = "LS-UART1"; - pinctrl-names = "default"; - pinctrl-0 = <&uart4_pins_b>; - status = "okay"; -}; - -&uart7 { - /* On Low speed expansion header */ - label = "LS-UART0"; - pinctrl-names = "default"; - pinctrl-0 = <&uart7_pins_a>; - status = "okay"; -}; - -/* Bluetooth */ -&usart2 { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&usart2_pins_a>; - pinctrl-1 = <&usart2_sleep_pins_a>; - st,hw-flow-ctrl; - status = "okay"; - - bluetooth { - compatible = "brcm,bcm43438-bt"; - max-speed = <3000000>; - shutdown-gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; - }; -}; - -&usbh_ehci { - phys = <&usbphyc_port0>; - phy-names = "usb"; - status = "okay"; -}; - -&usbotg_hs { - pinctrl-0 = <&usbotg_hs_pins_a>; - pinctrl-names = "default"; - phy-names = "usb2-phy"; - phys = <&usbphyc_port1 0>; - status = "okay"; - vbus-supply = <&vbus_otg>; -}; - -&usbphyc { - status = "okay"; -}; - -&usbphyc_port0 { - phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; -}; - -&usbphyc_port1 { - phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; -}; +/* This DT is here only for backward compatibility */ +#include "stm32mp157a-dhcor-avenger96.dts"arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts new file +38
-0@@ -0,0 +1,38 @@ +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) +/* + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved + * Author: Manivannan Sadhasivam <[email protected]> + * Copyright (C) 2020 Marek Vasut <[email protected]> + * + * DHCOR STM32MP1 variant: + * DHCR-STM32MP157A-C065-R102-V18-SPI-C-01LG + * DHCOR PCB number: 586-100 or newer + * Avenger96 PCB number: 588-200 or newer + */ + +/dts-v1/; + +#include "stm32mp157.dtsi" +#include "stm32mp15xc.dtsi" +#include "stm32mp15xx-dhcor-som.dtsi" +#include "stm32mp15xx-dhcor-avenger96.dtsi" + +/ { + model = "Arrow Electronics STM32MP157A Avenger96 board"; + compatible = "arrow,stm32mp157a-avenger96", "dh,stm32mp157a-dhcor-som", + "st,stm32mp157"; +}; + +&m_can1 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&m_can1_pins_b>; + pinctrl-1 = <&m_can1_sleep_pins_b>; + status = "disabled"; +}; + +&m_can2 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&m_can2_pins_a>; + pinctrl-1 = <&m_can2_sleep_pins_a>; + status = "disabled"; +};arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi new file +401
-0@@ -0,0 +1,401 @@ +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) +/* + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved + * Author: Manivannan Sadhasivam <[email protected]> + * Copyright (C) 2020 Marek Vasut <[email protected]> + */ + +/* Avenger96 uses DHCOR SoM configured for 1V8 IO operation */ +#include "stm32mp15xx-dhcor-io1v8.dtsi" + +/ { + aliases { + ethernet0 = ðernet0; + mmc0 = &sdmmc1; + serial0 = &uart4; + serial1 = &uart7; + serial2 = &usart2; + spi0 = &qspi; + }; + + /* XTal Q1 */ + cec_clock: clk-cec-fixed { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24000000>; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + hdmi-out { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con: endpoint { + remote-endpoint = <&adv7513_out>; + }; + }; + }; + + led { + compatible = "gpio-leds"; + led1 { + label = "green:user0"; + gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led2 { + label = "green:user1"; + gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + + led3 { + label = "green:user2"; + gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc1"; + default-state = "off"; + }; + + led4 { + label = "green:user3"; + gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "none"; + default-state = "off"; + panic-indicator; + }; + }; + + sd_switch: regulator-sd_switch { + compatible = "regulator-gpio"; + regulator-name = "sd_switch"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2900000>; + regulator-type = "voltage"; + regulator-always-on; + + gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>; + gpios-states = <0>; + states = <1800000 0x1>, + <2900000 0x0>; + }; + + sound { + compatible = "audio-graph-card"; + label = "STM32MP1-AV96-HDMI"; + dais = <&sai2a_port>; + status = "okay"; + }; + + wlan_pwr: regulator-wlan { + compatible = "regulator-fixed"; + + regulator-name = "wl-reg"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&adc { + pinctrl-names = "default"; + pinctrl-0 = <&adc12_ain_pins_b>; + vdd-supply = <&vdd>; + vdda-supply = <&vdda>; + vref-supply = <&vdda>; + status = "okay"; + + adc1: adc@0 { + st,adc-channels = <0 1 6>; + st,min-sample-time-nsecs = <5000>; + status = "okay"; + }; + + adc2: adc@100 { + st,adc-channels = <0 1 2>; + st,min-sample-time-nsecs = <5000>; + status = "okay"; + }; +}; + +ðernet0 { + status = "okay"; + pinctrl-0 = <ðernet0_rgmii_pins_c>; + pinctrl-1 = <ðernet0_rgmii_sleep_pins_c>; + pinctrl-names = "default", "sleep"; + phy-mode = "rgmii"; + max-speed = <1000>; + phy-handle = <&phy0>; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>; + reset-delay-us = <1000>; + + phy0: ethernet-phy@7 { + reg = <7>; + + rxc-skew-ps = <1500>; + rxdv-skew-ps = <540>; + rxd0-skew-ps = <420>; + rxd1-skew-ps = <420>; + rxd2-skew-ps = <420>; + rxd3-skew-ps = <420>; + + txc-skew-ps = <1440>; + txen-skew-ps = <540>; + txd0-skew-ps = <420>; + txd1-skew-ps = <420>; + txd2-skew-ps = <420>; + txd3-skew-ps = <420>; + }; + }; +}; + +&i2c1 { /* X6 I2C1 */ + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_b>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; +}; + +&i2c2 { /* X6 I2C2 */ + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_c>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; +}; + +&i2c4 { + hdmi-transmitter@3d { + compatible = "adi,adv7513"; + reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>; + reg-names = "main", "cec", "edid", "packet"; + clocks = <&cec_clock>; + clock-names = "cec"; + + avdd-supply = <&v3v3>; + dvdd-supply = <&v3v3>; + pvdd-supply = <&v3v3>; + dvdd-3v-supply = <&v3v3>; + bgvdd-supply = <&v3v3>; + + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; + interrupt-parent = <&gpiog>; + + status = "okay"; + + adi,input-depth = <8>; + adi,input-colorspace = "rgb"; + adi,input-clock = "1x"; + adi,input-style = <1>; + adi,input-justification = "evenly"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7513_in: endpoint { + remote-endpoint = <<dc_ep0_out>; + }; + }; + + port@1 { + reg = <1>; + adv7513_out: endpoint { + remote-endpoint = <&hdmi_con>; + }; + }; + + port@2 { + reg = <2>; + adv7513_i2s0: endpoint { + remote-endpoint = <&sai2a_endpoint>; + }; + }; + }; + }; +}; + +<dc { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <<dc_pins_d>; + pinctrl-1 = <<dc_sleep_pins_d>; + status = "okay"; + + port { + #address-cells = <1>; + #size-cells = <0>; + + ltdc_ep0_out: endpoint@0 { + reg = <0>; + remote-endpoint = <&adv7513_in>; + }; + }; +}; + +&sai2 { + clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sai2a_pins_c>; + pinctrl-1 = <&sai2a_sleep_pins_c>; + clock-names = "pclk", "x8k", "x11k"; + status = "okay"; + + sai2a: audio-controller@4400b004 { + #clock-cells = <0>; + dma-names = "tx"; + clocks = <&rcc SAI2_K>; + clock-names = "sai_ck"; + status = "okay"; + + sai2a_port: port { + sai2a_endpoint: endpoint { + remote-endpoint = <&adv7513_i2s0>; + format = "i2s"; + mclk-fs = <256>; + }; + }; + }; +}; + +&sdmmc1 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>; + cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + disable-wp; + st,sig-dir; + st,neg-edge; + st,use-ckin; + bus-width = <4>; + vmmc-supply = <&vdd_sd>; + vqmmc-supply = <&sd_switch>; + status = "okay"; +}; + +&sdmmc2 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>; + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>; + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>; + bus-width = <8>; + mmc-ddr-1_8v; + no-sd; + no-sdio; + non-removable; + st,neg-edge; + vmmc-supply = <&v3v3>; + vqmmc-supply = <&vdd_io>; + status = "okay"; +}; + +&sdmmc3 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc3_b4_pins_b>; + pinctrl-1 = <&sdmmc3_b4_od_pins_b>; + pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>; + broken-cd; + non-removable; + st,neg-edge; + bus-width = <4>; + vmmc-supply = <&wlan_pwr>; + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +&spi2 { + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins_a>; + cs-gpios = <&gpioi 0 0>; + status = "disabled"; + /delete-property/dmas; + /delete-property/dma-names; +}; + +&uart4 { + /* On Low speed expansion header */ + label = "LS-UART1"; + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins_b>; + status = "okay"; +}; + +&uart7 { + /* On Low speed expansion header */ + label = "LS-UART0"; + pinctrl-names = "default"; + pinctrl-0 = <&uart7_pins_a>; + status = "okay"; +}; + +/* Bluetooth */ +&usart2 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&usart2_pins_a>; + pinctrl-1 = <&usart2_sleep_pins_a>; + st,hw-flow-ctrl; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + max-speed = <3000000>; + shutdown-gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; + }; +}; + +&usbh_ehci { + phys = <&usbphyc_port0>; + phy-names = "usb"; + status = "okay"; +}; + +&usbotg_hs { + pinctrl-0 = <&usbotg_hs_pins_a>; + pinctrl-names = "default"; + phy-names = "usb2-phy"; + phys = <&usbphyc_port1 0>; + status = "okay"; + vbus-supply = <&vbus_otg>; +}; + +&usbphyc { + status = "okay"; +}; + +&usbphyc_port0 { + phy-supply = <&vdd_usb>; + vdda1v1-supply = <®11>; + vdda1v8-supply = <®18>; +}; + +&usbphyc_port1 { + phy-supply = <&vdd_usb>; + vdda1v1-supply = <®11>; + vdda1v8-supply = <®18>; +};arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi new file +23
-0@@ -0,0 +1,23 @@ +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) +/* + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved + * Author: Manivannan Sadhasivam <[email protected]> + * Copyright (C) 2020 Marek Vasut <[email protected]> + */ + +/ { + /* Enpirion EP3A8LQI U2 on the DHCOR */ + vdd_io: regulator-buck-io { + compatible = "regulator-fixed"; + regulator-name = "buck-io"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vdd>; + }; +}; + +&pwr_regulators { + vdd-supply = <&vdd_io>; +};arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi new file +209
-0@@ -0,0 +1,209 @@ +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) +/* + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved + * Author: Manivannan Sadhasivam <[email protected]> + * Copyright (C) 2020 Marek Vasut <[email protected]> + */ + +#include "stm32mp15-pinctrl.dtsi" +#include "stm32mp15xxac-pinctrl.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/mfd/st,stpmic1.h> + +/ { + aliases { + spi0 = &qspi; + }; + + memory@c0000000 { + device_type = "memory"; + reg = <0xc0000000 0x40000000>; + }; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; + + pmic: stpmic@33 { + compatible = "st,stpmic1"; + reg = <0x33>; + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + status = "okay"; + + regulators { + compatible = "st,stpmic1-regulators"; + + ldo1-supply = <&v3v3>; + ldo2-supply = <&v3v3>; + ldo3-supply = <&vdd_ddr>; + ldo5-supply = <&v3v3>; + ldo6-supply = <&v3v3>; + pwr_sw1-supply = <&bst_out>; + pwr_sw2-supply = <&bst_out>; + + vddcore: buck1 { + regulator-name = "vddcore"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd_ddr: buck2 { + regulator-name = "vdd_ddr"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd: buck3 { + regulator-name = "vdd"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + v3v3: buck4 { + regulator-name = "v3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-over-current-protection; + regulator-initial-mode = <0>; + }; + + vdda: ldo1 { + regulator-name = "vdda"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + interrupts = <IT_CURLIM_LDO1 0>; + }; + + v2v8: ldo2 { + regulator-name = "v2v8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + interrupts = <IT_CURLIM_LDO2 0>; + }; + + vtt_ddr: ldo3 { + regulator-name = "vtt_ddr"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <750000>; + regulator-always-on; + regulator-over-current-protection; + }; + + vdd_usb: ldo4 { + regulator-name = "vdd_usb"; + interrupts = <IT_CURLIM_LDO4 0>; + }; + + vdd_sd: ldo5 { + regulator-name = "vdd_sd"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + interrupts = <IT_CURLIM_LDO5 0>; + regulator-boot-on; + }; + + v1v8: ldo6 { + regulator-name = "v1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + interrupts = <IT_CURLIM_LDO6 0>; + regulator-enable-ramp-delay = <300000>; + }; + + vref_ddr: vref_ddr { + regulator-name = "vref_ddr"; + regulator-always-on; + }; + + bst_out: boost { + regulator-name = "bst_out"; + interrupts = <IT_OCP_BOOST 0>; + }; + + vbus_otg: pwr_sw1 { + regulator-name = "vbus_otg"; + interrupts = <IT_OCP_OTG 0>; + regulator-active-discharge = <1>; + }; + + vbus_sw: pwr_sw2 { + regulator-name = "vbus_sw"; + interrupts = <IT_OCP_SWOUT 0>; + regulator-active-discharge = <1>; + }; + }; + + onkey { + compatible = "st,stpmic1-onkey"; + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>; + interrupt-names = "onkey-falling", "onkey-rising"; + status = "okay"; + }; + + watchdog { + compatible = "st,stpmic1-wdt"; + status = "disabled"; + }; + }; + + eeprom@53 { + compatible = "atmel,24c02"; + reg = <0x53>; + pagesize = <16>; + }; +}; + +&iwdg2 { + timeout-sec = <32>; + status = "okay"; +}; + +&pwr_regulators { + vdd-supply = <&vdd>; + vdd_3v3_usbfs-supply = <&vdd_usb>; +}; + +&qspi { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>; + pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>; + reg = <0x58003000 0x1000>, <0x70000000 0x200000>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + flash0: spi-flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +&rng1 { + status = "okay"; +}; + +&rtc { + status = "okay"; +};Signature · 1 line
2.25.1
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Re: [PATCH V3 4/4] ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board
In reply to Marek VasutHi Marek
Quoted 28 lines · Marek Vasut
The Avenger96 is in fact an assembly of DH Electronics DHCOR SoM on top of an Avenger96 reference board. The DHCOR SoM can be populated with any STM32MP15xx. Split the DTs to reflect this such that the common SoM and Avenger96 parts are now in stm32mp15xx-dhcor-*dtsi and a specific example implementation of STM32MP157A SoM and Avenger96 board is separated into stm32mp157a-dhcor-*dts* . The
stm32mp157a-avenger96.dtsis retained for the sake of backward naming compatibility.Signed-off-by Marek Vasut <[email protected]>Cc Alexandre Torgue <[email protected]>Cc Manivannan Sadhasivam <[email protected]>Cc Maxime Coquelin <[email protected]>Cc Patrice Chotard <[email protected]>Cc Patrick Delaunay <[email protected]>To: [email protected]
---
V2: - Drop thestm32mp157a-dhcor-som.dtsi, as it was just include statements
- Add comment about what SoM+Board combination is currently supported
V3: No change--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/stm32mp157a-avenger96.dts | 618 +----------------- .../boot/dts/stm32mp157a-dhcor-avenger96.dts | 38 ++ .../boot/dts/stm32mp15xx-dhcor-avenger96.dtsi | 401 ++++++++++++ .../arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi | 23 + arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi | 209 ++++++ 6 files changed, 675 insertions(+), 615 deletions(-)
Quoted 5 lines
create mode 100644
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dtscreate mode 100644arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsicreate mode 100644arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsicreate mode 100644arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
Series applied on stm32-next.
Regards
Alex
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel