power_supply: Add additional health properties to the header
Subsystems (2)
PATCH 1/4 power_supply: Add additional health properties to the header
Add HEALTH_WARM, HEALTH_COOL and HEALTH_HOT to the health enum.
HEALTH_WARM, HEALTH_COOL, and HEALTH_HOT properties are taken from the JEITA spec.
--- Documentation/ABI/testing/sysfs-class-power | 2 +- drivers/power/supply/power_supply_sysfs.c | 2 +- include/linux/power_supply.h | 3 +++ 3 files changed, 5 insertions(+), 2 deletions(-)
Documentation/ABI/testing/sysfs-class-power +1 -1
@@ -190,7 +190,7 @@ Description: Valid values: "Unknown", "Good", "Overheat", "Dead", "Over voltage", "Unspecified failure", "Cold", "Watchdog timer expire", "Safety timer expire", - "Over current" + "Over current", "Warm", "Cool", "Hot" What: /sys/class/power_supply/<supply_name>/precharge_current Date: June 2017
drivers/power/supply/power_supply_sysfs.c +1 -1
@@ -61,7 +61,7 @@ static const char * const power_supply_charge_type_text[] = {static const char *const power_supply_health_text[] = {"Unknown" ,"Good" ,"Overheat" ,"Dead" ,"Over voltage" ,"Unspecified failure" ,"Cold" ,"Watchdog timer expire" , -"Safety timer expire" ,"Over current" +"Safety timer expire" ,"Over current" ,"Warm" ,"Cool" ,"Hot" };static const char *const power_supply_technology_text[] = {
include/linux/power_supply.h +3 -0
@@ -61,6 +61,9 @@ enum {POWER_SUPPLY_HEALTH_WATCHDOG_TIMER_EXPIRE ,POWER_SUPPLY_HEALTH_SAFETY_TIMER_EXPIRE ,POWER_SUPPLY_HEALTH_OVERCURRENT , +POWER_SUPPLY_HEALTH_WARM , +POWER_SUPPLY_HEALTH_COOL , + POWER_SUPPLY_HEALTH_HOT, }; enum {
Signature · 1 line
2.26.2
PATCH 2/4 dt-bindings: power: Convert battery.txt to battery.yaml
Convert the battery.txt file to yaml and fix up the examples.
--- .../bindings/power/supply/battery.txt | 82 +--------- .../bindings/power/supply/battery.yaml | 143 ++++++++++++++++++ 2 files changed, 144 insertions(+), 81 deletions(-) create mode 100644 Documentation/devicetree/bindings/power/supply/battery.yaml
Documentation/devicetree/bindings/power/supply/battery.txt +1 -81
@@ -1,81 +1 @@ -Battery Characteristics - -The devicetree battery node provides static battery characteristics. -In smart batteries, these are typically stored in non-volatile memory -on a fuel gauge chip. The battery node should be used where there is -no appropriate non-volatile memory, or it is unprogrammed/incorrect. - -Upstream dts files should not include battery nodes, unless the battery -represented cannot easily be replaced in the system by one of a -different type. This prevents unpredictable, potentially harmful, -behavior should a replacement that changes the battery type occur -without a corresponding update to the dtb. - -Required Properties: - - compatible: Must be "simple-battery" - -Optional Properties: - - voltage-min-design-microvolt: drained battery voltage - - voltage-max-design-microvolt: fully charged battery voltage - - energy-full-design-microwatt-hours: battery design energy - - charge-full-design-microamp-hours: battery design capacity - - precharge-current-microamp: current for pre-charge phase - - charge-term-current-microamp: current for charge termination phase - - constant-charge-current-max-microamp: maximum constant input current - - constant-charge-voltage-max-microvolt: maximum constant input voltage - - factory-internal-resistance-micro-ohms: battery factory internal resistance - - ocv-capacity-table-0: An array providing the open circuit voltage (OCV) - of the battery and corresponding battery capacity percent, which is used - to look up battery capacity according to current OCV value. And the open - circuit voltage unit is microvolt. - - ocv-capacity-table-1: Same as ocv-capacity-table-0 - ...... - - ocv-capacity-table-n: Same as ocv-capacity-table-0 - - ocv-capacity-celsius: An array containing the temperature in degree Celsius, - for each of the battery capacity lookup table. The first temperature value - specifies the OCV table 0, and the second temperature value specifies the - OCV table 1, and so on. - - resistance-temp-table: An array providing the temperature in degree Celsius - and corresponding battery internal resistance percent, which is used to look - up the resistance percent according to current temperature to get a accurate - batterty internal resistance in different temperatures. - -Battery properties are named, where possible, for the corresponding -elements in enum power_supply_property, defined in -https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/include/linux/power_supply.h - -Batteries must be referenced by chargers and/or fuel-gauges -using a phandle. The phandle's property should be named -"monitored-battery". - -Example: - - bat: battery { - compatible = "simple-battery"; - voltage-min-design-microvolt = <3200000>; - voltage-max-design-microvolt = <4200000>; - energy-full-design-microwatt-hours = <5290000>; - charge-full-design-microamp-hours = <1430000>; - precharge-current-microamp = <256000>; - charge-term-current-microamp = <128000>; - constant-charge-current-max-microamp = <900000>; - constant-charge-voltage-max-microvolt = <4200000>; - factory-internal-resistance-micro-ohms = <250000>; - ocv-capacity-celsius = <(-10) 0 10>; - ocv-capacity-table-0 = <4185000 100>, <4113000 95>, <4066000 90>, ...; - ocv-capacity-table-1 = <4200000 100>, <4185000 95>, <4113000 90>, ...; - ocv-capacity-table-2 = <4250000 100>, <4200000 95>, <4185000 90>, ...; - resistance-temp-table = <20 100>, <10 90>, <0 80>, <(-10) 60>; - }; - - charger: charger@11 { - .... - monitored-battery = <&bat>; - ... - }; - - fuel_gauge: fuel-gauge@22 { - .... - monitored-battery = <&bat>; - ... - }; +The contents of this file has been moved to battery.yaml
Documentation/devicetree/bindings/power/supply/battery.yaml new file +143 -0
143 lines not on this page · raw message
Signature · 1 line
2.26.2
PATCH 3/4 dt-bindings: power: Add the bindings for the bq2515x family of chargers.
In reply to Dan MurphyFrom: Ricardo Rivera-Matos <[email protected]>
The BQ2515X family of devices are highly integrated battery management ICs that integrate the most common functions for wearable devices namely a charger, an output voltage rail, ADC for battery and system monitoring, and a push-button controller.
Datasheets:
http://www.ti.com/lit/ds/symlink/bq25150.pdf
http://www.ti.com/lit/ds/symlink/bq25155.pdf
--- .../bindings/power/supply/bq2515x.yaml | 110 ++++++++++++++++++ 1 file changed, 110 insertions(+) create mode 100644 Documentation/devicetree/bindings/power/supply/bq2515x.yaml
Documentation/devicetree/bindings/power/supply/bq2515x.yaml new file +110 -0
@@ -0,0 +1,110 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (C) 2020 Texas Instruments Incorporated +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/bq2515x.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: TI bq2515x 500-mA Linear charger family + +maintainers: + - Dan Murphy <[email protected]> + - Ricardo Rivera-Matos <[email protected]> + +description: | + The BQ2515x family is a highly integrated battery charge management IC that + integrates the most common functions for wearable devices, namely a charger, + an output voltage rail, ADC for battery and system monitoring, and + push-button controller. + + Specifications about the charger can be found at: + http://www.ti.com/lit/ds/symlink/bq25150.pdf + http://www.ti.com/lit/ds/symlink/bq25155.pdf + +properties: + compatible: + enum: + - ti,bq25150 + - ti,bq25155 + + reg: + maxItems: 1 + description: I2C address of the charger. + + ac-detect-gpios: + description: | + GPIO used for connecting the bq2515x device PG (AC Detect) + pin. This pin should be used if possible as this is the + recommended way to obtain the charger's input PG state. + If this pin is not specified a software-based approach for PG + detection is used. + maxItems: 1 + + reset-gpios: + description: GPIO used for hardware reset. + maxItems: 1 + + low-power-gpios: + description: GPIO used for low power mode of IC. + maxItems: 1 + + charge-enable-gpios: + description: GPIO used to turn on and off charging. + maxItems: 1 + + constant-charge-current-max-microamp: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Maximum charging current in micro Amps. + minimum: 50000 + maximum: 600000 + + precharge-current-max-microamp: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Maximum precharging current in micro Amps. + minimum: 1250 + maximum: 77500 + + input-current-limit-microamp: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Maximum input current in micro Amps. + minimum: 50000 + maximum: 500000 + + constant-charge-voltage-max-microvolt: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Maximum charging voltage in micro volts. + minimum: 3600000 + maximum: 4600000 + + monitored-battery: + $ref: battery.yaml# + +required: + - compatible + - reg + +examples: + - | + bat: battery { + compatible = "simple-battery"; + constant-charge-current-max-microamp = <50000>; + precharge-current-microamp = <2500>; + constant-charge-voltage-max-microvolt = <4000000>; + }; + #include <dt-bindings/gpio/gpio.h> + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + bq25150: charger@6b { + compatible = "ti,bq25150"; + reg = <0x6b>; + monitored-battery = <&bat>; + input-current-limit-microamp = <100000>; + + ac-detect-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; + low-power-gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; + charge-enable-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; + }; + };
Signature · 1 line
2.26.2
PATCH 4/4 power: supply: bq25150 introduce the bq25150
In reply to Dan MurphyFrom: Ricardo Rivera-Matos <[email protected]>
Introduce the bq2515x family of chargers.
The BQ2515X family of devices are highly integrated battery management ICs that integrate the most common functions for wearable devices namely a charger, an output voltage rail, ADC for battery and system monitoring, and a push-button controller.
Datasheets:
bq25150 - http://www.ti.com/lit/ds/symlink/bq25150.pdf bq25155 - http://www.ti.com/lit/ds/symlink/bq25155.pdf
--- drivers/power/supply/Kconfig | 13 + drivers/power/supply/Makefile | 1 + drivers/power/supply/bq2515x_charger.c | 1159 ++++++++++++++++++++++++ 3 files changed, 1173 insertions(+) create mode 100644 drivers/power/supply/bq2515x_charger.c
drivers/power/supply/Kconfig +13 -0
@@ -589,6 +589,19 @@ config CHARGER_BQ24735 help Say Y to enable support for the TI BQ24735 battery charger. +config CHARGER_BQ2515X + tristate "TI BQ2515X battery charger family" + depends on I2C + depends on GPIOLIB || COMPILE_TEST + select REGMAP_I2C + help + Say Y to enable support for the TI BQ2515X family of battery + charging integrated circuits. The BQ2515X are highly integrated + battery charge management ICs that integrate the most common + functions for wearable devices, namely a charger, an output voltage + rail, ADC for battery and system monitoring, and push-button + controller. + config CHARGER_BQ25890 tristate "TI BQ25890 battery charger driver" depends on I2C
drivers/power/supply/Makefile +1 -0
@@ -80,6 +80,7 @@ obj-$(CONFIG_CHARGER_BQ2415X) += bq2415x_charger.o obj-$(CONFIG_CHARGER_BQ24190) += bq24190_charger.o obj-$(CONFIG_CHARGER_BQ24257) += bq24257_charger.o obj-$(CONFIG_CHARGER_BQ24735) += bq24735-charger.o +obj-$(CONFIG_CHARGER_BQ2515X) += bq2515x_charger.o obj-$(CONFIG_CHARGER_BQ25890) += bq25890_charger.o obj-$(CONFIG_CHARGER_SMB347) += smb347-charger.o obj-$(CONFIG_CHARGER_TPS65090) += tps65090-charger.o
drivers/power/supply/bq2515x_charger.c new file +1159 -0
1,159 lines not on this page · raw message
Signature · 1 line
2.26.2