Skip to contentSkip to conversation

Add initial support for MikroTik RB3011

PATCH Applied Jonathan McDowell 3 participants 6 messages May 18, 2020 – May 29, 2020

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

cover Add initial support for MikroTik RB3011

This patches do some prep (device tree vendor addition, missing ethernet definitions for IPQ8064 dts) and then add an initial device tree for the MikroTik RB3011 1U router, which is an IPQ8064 device with 1G RAM. They are sufficient to boot with an initrd, the serial console and the first 5 switch ports fully functional (the second bank of 5 require some extra patches to the QCA8K driver which will follow later). The bootloader NOR is also supported, but the 128MB NAND is not yet enabled.

Jonathan McDowell (3):
dt-bindings: vendor-prefixes: Add MikroTik
ARM: dts: qcom: add ethernet definitions to ipq8064
ARM: dts: qcom: Add MikroTik RB3011

 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 arch/arm/boot/dts/Makefile                    |   1 +
 arch/arm/boot/dts/qcom-ipq8064-rb3011.dts     | 308 ++++++++++++++++++
 arch/arm/boot/dts/qcom-ipq8064.dtsi           | 108 ++++++
 4 files changed, 419 insertions(+)
 create mode 100644 arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
Signature · 1 line
2.20.1
#1 lore raw

PATCH 1/3 dt-bindings: vendor-prefixes: Add MikroTik

MikroTik (SIA Mikrotīkls) is a Latvian company who develop routers and wireless ISP systems.

---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/vendor-prefixes.yaml +2 -0
index d3891386d671..d3277fe6640b 100644
@@ -633,6 +633,8 @@ patternProperties:
     description: Microsoft Corporation
   "^mikroe,.*":
     description: MikroElektronika d.o.o.
+  "^mikrotik,.*":
+    description: MikroTik
   "^miniand,.*":
     description: Miniand Tech
   "^minix,.*":
Signature · 1 line
2.20.1
maintainer Applied
#2 lore raw

Re: [PATCH 1/3] dt-bindings: vendor-prefixes: Add MikroTik

Quoted 8 lines · Jonathan McDowell

MikroTik (SIA Mikrotīkls) is a Latvian company who develop routers and wireless ISP systems.

---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

Applied, thanks!

#3 lore raw

PATCH 2/3 ARM: dts: qcom: add ethernet definitions to ipq8064

In reply to Jonathan McDowell

Plumb in the 4 IPQ8064 stmmac based ethernet interfaces.

---
 arch/arm/boot/dts/qcom-ipq8064.dtsi | 108 ++++++++++++++++++++++++++++
 1 file changed, 108 insertions(+)
arch/arm/boot/dts/qcom-ipq8064.dtsi +108 -0
index b912da9a3ff3..9c0d5510c805 100644
@@ -597,6 +597,114 @@
 			perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
 		};
 
+		nss_common: syscon@03000000 {
+			compatible = "syscon";
+			reg = <0x03000000 0x0000FFFF>;
+		};
+
+		qsgmii_csr: syscon@1bb00000 {
+			compatible = "syscon";
+			reg = <0x1bb00000 0x000001FF>;
+		};
+
+		stmmac_axi_setup: stmmac-axi-config {
+			snps,wr_osr_lmt = <7>;
+			snps,rd_osr_lmt = <7>;
+			snps,blen = <16 0 0 0 0 0 0>;
+		};
+
+		gmac0: ethernet@37000000 {
+			device_type = "network";
+			compatible = "qcom,ipq806x-gmac";
+			reg = <0x37000000 0x200000>;
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,pbl = <32>;
+			snps,aal = <1>;
+
+			qcom,nss-common = <&nss_common>;
+			qcom,qsgmii-csr = <&qsgmii_csr>;
+
+			clocks = <&gcc GMAC_CORE1_CLK>;
+			clock-names = "stmmaceth";
+
+			resets = <&gcc GMAC_CORE1_RESET>;
+			reset-names = "stmmaceth";
+
+			status = "disabled";
+		};
+
+		gmac1: ethernet@37200000 {
+			device_type = "network";
+			compatible = "qcom,ipq806x-gmac";
+			reg = <0x37200000 0x200000>;
+			interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,pbl = <32>;
+			snps,aal = <1>;
+
+			qcom,nss-common = <&nss_common>;
+			qcom,qsgmii-csr = <&qsgmii_csr>;
+
+			clocks = <&gcc GMAC_CORE2_CLK>;
+			clock-names = "stmmaceth";
+
+			resets = <&gcc GMAC_CORE2_RESET>;
+			reset-names = "stmmaceth";
+
+			status = "disabled";
+		};
+
+		gmac2: ethernet@37400000 {
+			device_type = "network";
+			compatible = "qcom,ipq806x-gmac";
+			reg = <0x37400000 0x200000>;
+			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,pbl = <32>;
+			snps,aal = <1>;
+
+			qcom,nss-common = <&nss_common>;
+			qcom,qsgmii-csr = <&qsgmii_csr>;
+
+			clocks = <&gcc GMAC_CORE3_CLK>;
+			clock-names = "stmmaceth";
+
+			resets = <&gcc GMAC_CORE3_RESET>;
+			reset-names = "stmmaceth";
+
+			status = "disabled";
+		};
+
+		gmac3: ethernet@37600000 {
+			device_type = "network";
+			compatible = "qcom,ipq806x-gmac";
+			reg = <0x37600000 0x200000>;
+			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,pbl = <32>;
+			snps,aal = <1>;
+
+			qcom,nss-common = <&nss_common>;
+			qcom,qsgmii-csr = <&qsgmii_csr>;
+
+			clocks = <&gcc GMAC_CORE4_CLK>;
+			clock-names = "stmmaceth";
+
+			resets = <&gcc GMAC_CORE4_RESET>;
+			reset-names = "stmmaceth";
+
+			status = "disabled";
+		};
+
 		vsdcc_fixed: vsdcc-regulator {
 			compatible = "regulator-fixed";
 			regulator-name = "SDCC Power";
Signature · 1 line
2.20.1
#4 lore raw

PATCH 3/3 ARM: dts: qcom: Add MikroTik RB3011

In reply to Jonathan McDowell

This patch adds a DTS file for the MikroTik RouterBoard 3011, which is a 1U rackmount router based on the IPQ8064, supporting the serial UART, dual QCA8337 Gigabit ethernet switches, boot loader NOR and user LED device.

---
 arch/arm/boot/dts/Makefile                |   1 +
 arch/arm/boot/dts/qcom-ipq8064-rb3011.dts | 308 ++++++++++++++++++++++
 2 files changed, 309 insertions(+)
 create mode 100644 arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
arch/arm/boot/dts/Makefile +1 -0
index e8dd99201397..e697a4bd7426 100644
@@ -884,6 +884,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-ipq4019-ap.dk07.1-c1.dtb \
 	qcom-ipq4019-ap.dk07.1-c2.dtb \
 	qcom-ipq8064-ap148.dtb \
+	qcom-ipq8064-rb3011.dtb \
 	qcom-msm8660-surf.dtb \
 	qcom-msm8960-cdp.dtb \
 	qcom-msm8974-fairphone-fp2.dtb \
arch/arm/boot/dts/qcom-ipq8064-rb3011.dts new file +308 -0

308 lines not on this page · raw message

Signature · 1 line
2.20.1
#5 lore raw

Re: [PATCH 3/3] ARM: dts: qcom: Add MikroTik RB3011

Quoted 6 lines · Jonathan McDowell

This patch adds a DTS file for the MikroTik RouterBoard 3011, which is a 1U rackmount router based on the IPQ8064, supporting the serial UART, dual QCA8337 Gigabit ethernet switches, boot loader NOR and user LED device.

Patch 2 and 3 picked up for 5.9

Thanks,
Bjorn

Quoted 335 lines
---
 arch/arm/boot/dts/Makefile                |   1 +
 arch/arm/boot/dts/qcom-ipq8064-rb3011.dts | 308 ++++++++++++++++++++++
 2 files changed, 309 insertions(+)
 create mode 100644 arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
arch/arm/boot/dts/Makefile +1 -0
index e8dd99201397..e697a4bd7426 100644
@@ -884,6 +884,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-ipq4019-ap.dk07.1-c1.dtb \
 	qcom-ipq4019-ap.dk07.1-c2.dtb \
 	qcom-ipq8064-ap148.dtb \
+	qcom-ipq8064-rb3011.dtb \
 	qcom-msm8660-surf.dtb \
 	qcom-msm8960-cdp.dtb \
 	qcom-msm8974-fairphone-fp2.dtb \
arch/arm/boot/dts/qcom-ipq8064-rb3011.dts new file +308 -0
new file mode 100644
index 000000000000..282b89ce3d45
@@ -0,0 +1,308 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-ipq8064.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "MikroTik RB3011UiAS-RM";
+	compatible = "mikrotik,rb3011";
+
+	aliases {
+		serial0 = &gsbi7_serial;
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac3;
+		mdio-gpio0 = &mdio0;
+		mdio-gpio1 = &mdio1;
+	};
+
+	chosen {
+		bootargs = "loglevel=8 console=ttyMSM0,115200";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		reg = <0x42000000 0x3e000000>;
+		device_type = "memory";
+	};
+
+	mdio0: mdio@0 {
+		status = "okay";
+		compatible = "virtual,mdio-gpio";
+		gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
+			<&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-0 = <&mdio0_pins>;
+		pinctrl-names = "default";
+
+		switch0: switch@10 {
+			compatible = "qca,qca8337";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			dsa,member = <0 0>;
+
+			pinctrl-0 = <&sw0_reset_pin>;
+			pinctrl-names = "default";
+
+			reset-gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>;
+			reg = <0x10>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				switch0cpu: port@0 {
+					reg = <0>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "rgmii-id";
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "sw1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "sw2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "sw3";
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "sw4";
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "sw5";
+				};
+			};
+		};
+	};
+
+	mdio1: mdio@1 {
+		status = "okay";
+		compatible = "virtual,mdio-gpio";
+		gpios = <&qcom_pinmux 11 GPIO_ACTIVE_HIGH>,
+			<&qcom_pinmux 10 GPIO_ACTIVE_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-0 = <&mdio1_pins>;
+		pinctrl-names = "default";
+
+		switch1: switch@14 {
+			compatible = "qca,qca8337";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			dsa,member = <1 0>;
+
+			pinctrl-0 = <&sw1_reset_pin>;
+			pinctrl-names = "default";
+
+			reset-gpios = <&qcom_pinmux 17 GPIO_ACTIVE_LOW>;
+			reg = <0x10>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				switch1cpu: port@0 {
+					reg = <0>;
+					label = "cpu";
+					ethernet = <&gmac3>;
+					phy-mode = "sgmii";
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "sw6";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "sw7";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "sw8";
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "sw9";
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "sw10";
+				};
+			};
+		};
+	};
+
+	soc {
+		gsbi5: gsbi@1a200000 {
+			qcom,mode = <GSBI_PROT_SPI>;
+			status = "okay";
+
+			spi4: spi@1a280000 {
+				status = "okay";
+				spi-max-frequency = <50000000>;
+
+				pinctrl-0 = <&spi_pins>;
+				pinctrl-names = "default";
+
+				cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+				norflash: s25fl016k@0 {
+					compatible = "jedec,spi-nor";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					spi-max-frequency = <50000000>;
+					reg = <0>;
+
+					partition@0 {
+						label = "RouterBoot";
+						reg = <0x0 0x40000>;
+					};
+				};
+			};
+		};
+
+		gpio_keys {
+			compatible = "gpio-keys";
+			pinctrl-0 = <&buttons_pins>;
+			pinctrl-names = "default";
+
+			button@1 {
+				label = "reset";
+				linux,code = <KEY_RESTART>;
+				gpios = <&qcom_pinmux 66 GPIO_ACTIVE_LOW>;
+				linux,input-type = <1>;
+				debounce-interval = <60>;
+			};
+		};
+
+		leds {
+			compatible = "gpio-leds";
+			pinctrl-0 = <&leds_pins>;
+			pinctrl-names = "default";
+
+			led@7 {
+				label = "rb3011:green:user";
+				gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+			};
+		};
+
+	};
+};
+
+&gmac0 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	qcom,id = <0>;
+	phy-handle = <&switch0cpu>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gmac3 {
+	status = "okay";
+
+	phy-mode = "sgmii";
+	qcom,id = <3>;
+	phy-handle = <&switch1cpu>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gsbi7 {
+	status = "okay";
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+};
+
+&gsbi7_serial {
+	status = "okay";
+};
+
+&qcom_pinmux {
+	buttons_pins: buttons_pins {
+		mux {
+			pins = "gpio66";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	leds_pins: leds_pins {
+		mux {
+			pins = "gpio33";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	mdio0_pins: mdio0_pins {
+		mux {
+			pins = "gpio0", "gpio1";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	mdio1_pins: mdio1_pins {
+		mux {
+			pins = "gpio10", "gpio11";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	sw0_reset_pin: sw0_reset_pin {
+		mux {
+			pins = "gpio16";
+			drive-strength = <16>;
+			function = "gpio";
+			bias-disable;
+			input-disable;
+		};
+	};
+
+	sw1_reset_pin: sw1_reset_pin {
+		mux {
+			pins = "gpio17";
+			drive-strength = <16>;
+			function = "gpio";
+			bias-disable;
+			input-disable;
+		};
+	};
+};
Signature · 1 line
2.20.1