rockchip: rk3399: Add SPI boot
Subsystems (3)
v4 cover rockchip: rk3399: Add SPI boot
Now, nvme scan seems stable with environment.
This series v4 version for SPI boot support on rk3399.
Changes for v4:
- adjust env offset, size
changes for v3:
- SPI env offset, size changes based on roc-rk3399-pc Changes for v2:
- same defconfig to support both MMC, SPI boot
- add spi flash program document
Any inputs?
Jagan.
Jagan Teki (4):
Makefile: Drop to handle rkspi image type
roc-rk3399-pc: Mark default env from SPI
roc-rk3399-pc: Add SPI boot
doc: rockchip: Document SPI flash program steps
Makefile | 11 ++-------- arch/arm/dts/rk3399-roc-pc-u-boot.dtsi | 12 ++++++++++- configs/roc-pc-mezzanine-rk3399_defconfig | 7 +++++- configs/roc-pc-rk3399_defconfig | 7 +++++- doc/board/rockchip/rockchip.rst | 26 ++++++++++++++++++++++- include/configs/roc-pc-rk3399.h | 4 ---- 6 files changed, 50 insertions(+), 17 deletions(-)
Signature · 1 line
2.20.1
A message that is not in the archive (sent off-list or not yet received): 20200608181708.17842-1-jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org
PATCH v4 1/4 Makefile: Drop to handle rkspi image type
On rockchip platforms, SPI boot image creation is not straightforward like MMC boot image creation where former requires to specify tpl, spl in multimage format in mkimage, and later simply do a concatenate mkimaged-tpl with spl.
On this note, let drop rkspi image type creation via kbuild and let inform via rockchip.rst
---
Changes for v4:
- none
Makefile | 11 ++--------- 1 file changed, 2 insertions(+), 9 deletions(-)
Makefile +2 -9
@@ -1438,22 +1438,15 @@ u-boot-with-spl.bin: $(SPL_IMAGE) $(SPL_PAYLOAD) FORCE ifeq ($(CONFIG_ARCH_ROCKCHIP),y) -# rockchip image type -ifeq ($(CONFIG_SPL_SPI_LOAD),y) -ROCKCHIP_IMG_TYPE := rkspi -else -ROCKCHIP_IMG_TYPE := rksd -endif - # TPL + SPL ifeq ($(CONFIG_SPL)$(CONFIG_TPL),yy) -MKIMAGEFLAGS_u-boot-tpl-rockchip.bin = -n $(CONFIG_SYS_SOC) -T $(ROCKCHIP_IMG_TYPE) +MKIMAGEFLAGS_u-boot-tpl-rockchip.bin = -n $(CONFIG_SYS_SOC) -T rksd tpl/u-boot-tpl-rockchip.bin: tpl/u-boot-tpl.bin FORCE $(call if_changed,mkimage) idbloader.img: tpl/u-boot-tpl-rockchip.bin spl/u-boot-spl.bin FORCE $(call if_changed,cat) else -MKIMAGEFLAGS_idbloader.img = -n $(CONFIG_SYS_SOC) -T $(ROCKCHIP_IMG_TYPE) +MKIMAGEFLAGS_idbloader.img = -n $(CONFIG_SYS_SOC) -T rksd idbloader.img: spl/u-boot-spl.bin FORCE $(call if_changed,mkimage) endif
Signature · 1 line
2.20.1
PATCH v4 2/4 roc-rk3399-pc: Mark default env from SPI
In reply to a message not in the archiveMark the default U-Boot environment as SPI flash since this is an on board flash device.
Updated env offset, size in contrast with default since the U-Boot proper has starting from 384K.
---
Changes for v4:
- adjust env offset, size
configs/roc-pc-mezzanine-rk3399_defconfig | 4 +++- configs/roc-pc-rk3399_defconfig | 4 +++- include/configs/roc-pc-rk3399.h | 4 ---- 3 files changed, 6 insertions(+), 6 deletions(-)
configs/roc-pc-mezzanine-rk3399_defconfig +3 -1
@@ -1,7 +1,9 @@ CONFIG_ARM=y CONFIG_ARCH_ROCKCHIP=y CONFIG_SYS_TEXT_BASE=0x00200000 +CONFIG_ENV_SIZE=0x8000 CONFIG_ENV_OFFSET=0x3F8000 +CONFIG_ENV_SECT_SIZE=0x1000 CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_ROC_PC_RK3399=y CONFIG_NR_DRAM_BANKS=1
@@ -25,7 +27,7 @@ CONFIG_CMD_TIME=y CONFIG_SPL_OF_CONTROL=y CONFIG_DEFAULT_DEVICE_TREE="rk3399-roc-pc-mezzanine" CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents" -CONFIG_ENV_IS_IN_MMC=y +CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_ROCKCHIP_GPIO=y CONFIG_SYS_I2C_ROCKCHIP=y
configs/roc-pc-rk3399_defconfig +3 -1
@@ -1,7 +1,9 @@ CONFIG_ARM=y CONFIG_ARCH_ROCKCHIP=y CONFIG_SYS_TEXT_BASE=0x00200000 +CONFIG_ENV_SIZE=0x8000 CONFIG_ENV_OFFSET=0x3F8000 +CONFIG_ENV_SECT_SIZE=0x1000 CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_ROC_PC_RK3399=y CONFIG_NR_DRAM_BANKS=1
@@ -24,7 +26,7 @@ CONFIG_CMD_TIME=y CONFIG_SPL_OF_CONTROL=y CONFIG_DEFAULT_DEVICE_TREE="rk3399-roc-pc" CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents" -CONFIG_ENV_IS_IN_MMC=y +CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_ROCKCHIP_GPIO=y CONFIG_SYS_I2C_ROCKCHIP=y
include/configs/roc-pc-rk3399.h +0 -4
@@ -13,10 +13,6 @@#include <configs/rk3399_common.h> -#if defined(CONFIG_ENV_IS_IN_MMC ) -# define CONFIG_SYS_MMC_ENV_DEV 0 -#endif -#define SDRAM_BANK_SIZE (2UL << 30)#endif
Signature · 1 line
2.20.1
PATCH v4 3/4 roc-rk3399-pc: Add SPI boot
In reply to a message not in the archiveU-Boot TPL 2020.07-rc3-00090-gd4e919f927-dirty (Jun 01 2020 - 23:45:53) Channel 0: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB Channel 1: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB 256B stride
256B stridelpddr4_set_rate: change freq to 400000000 mhz 0, 1lpddr4_set_rate: change freq to 800000000 mhz 1, 0
Trying to boot from BOOTROM
Returning to boot ROM...
U-Boot SPL 2020.07-rc3-00087-ga21e9fd385 (Jun 02 2020 - 00:09:45 +0530) Trying to boot from MMC1
NOTICE: BL31: v2.2(release): NOTICE: BL31: Built : 15:05:37, May 12 2020
U-Boot 2020.07-rc3-00087-ga21e9fd385 (Jun 02 2020 - 00:09:45 +0530)
SoC: Rockchip rk3399 Reset cause: POR Model: Firefly ROC-RK3399-PC Board DRAM: 3.9 GiB PMIC: RK808 MMC: mmc@fe320000: 1, sdhci@fe330000: 0
Loading Environment from SPI Flash... SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment
In: serial Out: serial Err: serial Model: Firefly ROC-RK3399-PC Board
---
Changes for v4:
- none
arch/arm/dts/rk3399-roc-pc-u-boot.dtsi | 12 +++++++++++- configs/roc-pc-mezzanine-rk3399_defconfig | 3 +++ configs/roc-pc-rk3399_defconfig | 3 +++ 3 files changed, 17 insertions(+), 1 deletion(-)
arch/arm/dts/rk3399-roc-pc-u-boot.dtsi +11 -1
@@ -12,7 +12,11 @@ }; chosen { - u-boot,spl-boot-order = "same-as-spl", &sdhci, &sdmmc; + u-boot,spl-boot-order = "same-as-spl", &spi_flash, &sdhci, &sdmmc; + }; + + config { + u-boot,spl-payload-offset = <0x60000>; /* @ 384KB */ }; vcc_hub_en: vcc_hub_en-regulator {
@@ -40,6 +44,12 @@ vin-supply = <&vcc_vbus_typec0>; }; +&spi1 { + spi_flash: flash@0 { + u-boot,dm-pre-reloc; + }; +}; + &vdd_log { regulator-min-microvolt = <430000>; regulator-init-microvolt = <950000>;
configs/roc-pc-mezzanine-rk3399_defconfig +3 -0
@@ -9,12 +9,15 @@ CONFIG_TARGET_ROC_PC_RK3399=y CONFIG_NR_DRAM_BANKS=1 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SPL_SPI_FLASH_SUPPORT=y +CONFIG_SPL_SPI_SUPPORT=y CONFIG_DEBUG_UART=y CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-roc-pc-mezzanine.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set CONFIG_SPL_STACK_R=y CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 +CONFIG_SPL_SPI_LOAD=y CONFIG_TPL=y CONFIG_TPL_GPIO_SUPPORT=y CONFIG_CMD_BOOTZ=y
configs/roc-pc-rk3399_defconfig +3 -0
@@ -9,12 +9,15 @@ CONFIG_TARGET_ROC_PC_RK3399=y CONFIG_NR_DRAM_BANKS=1 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SPL_SPI_FLASH_SUPPORT=y +CONFIG_SPL_SPI_SUPPORT=y CONFIG_DEBUG_UART=y CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-roc-pc.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set CONFIG_SPL_STACK_R=y CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 +CONFIG_SPL_SPI_LOAD=y CONFIG_TPL=y CONFIG_TPL_GPIO_SUPPORT=y CONFIG_CMD_BOOTZ=y
Signature · 1 line
2.20.1
PATCH v4 4/4 doc: rockchip: Document SPI flash program steps
In reply to a message not in the archiveDocument SPI flash program steps for rockchip platforms.
---
Changes for v4:
- none
doc/board/rockchip/rockchip.rst | 26 +++++++++++++++++++++++++- 1 file changed, 25 insertions(+), 1 deletion(-)
doc/board/rockchip/rockchip.rst +25 -1
@@ -162,6 +162,30 @@ Program the flash:: Note: for rockchip 32-bit platforms the U-Boot proper image is u-boot-dtb.img +SPI +^^^ + +Generating idbloader for SPI boot would require to input a multi image +image format to mkimage tool instead of concerting (like for MMC boot). + +SPL-alone SPI boot image:: + + ./tools/mkimage -n rk3399 -T rkspi -d spl/u-boot-spl.bin idbloader.img + +TPL+SPL SPI boot image:: + + ./tools/mkimage -n rk3399 -T rkspi -d tpl/u-boot-tpl.bin:spl/u-boot-spl.bin idbloader.img + +Copy SPI boot images into SD card and boot from SD:: + + sf probe + load mmc 1:1 $kernel_addr_r idbloader.img + sf erase 0 +$filesize + sf write $kernel_addr_r 0 ${filesize} + load mmc 1:1 ${kernel_addr_r} u-boot.itb + sf erase 0x60000 +$filesize + sf write $kernel_addr_r 0x60000 ${filesize} + TODO ----
@@ -171,4 +195,4 @@ TODO - Add missing SoC's with it boards list .. Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org> -.. Sunday 24 May 2020 10:08:41 PM IST +.. Tuesday 02 June 2020 12:18:57 AM IST
Signature · 1 line
2.20.1