rockchip: rk3399pro: Add Add Rock Pi N10 support
Subsystems (2)
cover rockchip: rk3399pro: Add Add Rock Pi N10 support
Rock Pi N10 is a Rockchip RK3399Pro based SBC, which has
- VMARC RK3399Pro SOM (as per SMARC standard) from Vamrs.
- Dalang carrier board from Radxa.
All the required dts(i) files are synced from linux-next v5.7-rc1 since the current sync available for rk3399 is the same.
Any inputs?
Jagan.
Jagan Teki (4):
arm64: dts: rockchip: Sync v5.7-rc1 rk3399pro.dtsi
arm64: dts: rockchip: Sync v5.7-rc1 VMARC RK3399Pro SOM
ARM: dts: rockchip: Sync v5.7-rc1 Radxa Dalang Carrier
arm64: dts: rockchip: Add Radxa Rock Pi N10 initial support
arch/arm/dts/Makefile | 3 +- .../arm/dts/rk3399pro-rock-pi-n10-u-boot.dtsi | 7 + arch/arm/dts/rk3399pro-rock-pi-n10.dts | 18 + arch/arm/dts/rk3399pro-u-boot.dtsi | 6 + arch/arm/dts/rk3399pro-vmarc-som.dtsi | 333 ++++++++++++++++++ arch/arm/dts/rk3399pro.dtsi | 22 ++ .../dts/rockchip-radxa-dalang-carrier.dtsi | 81 +++++ board/rockchip/evb_rk3399/MAINTAINERS | 6 + configs/rock-pi-n10-rk3399pro_defconfig | 46 +++ 9 files changed, 521 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/rk3399pro-rock-pi-n10-u-boot.dtsi create mode 100644 arch/arm/dts/rk3399pro-rock-pi-n10.dts create mode 100644 arch/arm/dts/rk3399pro-u-boot.dtsi create mode 100644 arch/arm/dts/rk3399pro-vmarc-som.dtsi create mode 100644 arch/arm/dts/rk3399pro.dtsi create mode 100644 arch/arm/dts/rockchip-radxa-dalang-carrier.dtsi create mode 100644 configs/rock-pi-n10-rk3399pro_defconfig
Signature · 1 line
2.25.1
A message that is not in the archive (sent off-list or not yet received): 20200610103658.96678-1-jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org
PATCH 1/4 arm64: dts: rockchip: Sync v5.7-rc1 rk3399pro.dtsi
Sync linux-next v5.7-rc1 rk3399pro.dtsi.
--- arch/arm/dts/rk3399pro.dtsi | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+) create mode 100644 arch/arm/dts/rk3399pro.dtsi
arch/arm/dts/rk3399pro.dtsi new file +22 -0
@@ -0,0 +1,22 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd. + +#include "rk3399.dtsi" + +/ { + compatible = "rockchip,rk3399pro"; +}; + +/* Default to enabled since AP talk to NPU part over pcie */ +&pcie_phy { + status = "okay"; +}; + +/* Default to enabled since AP talk to NPU part over pcie */ +&pcie0 { + ep-gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>; + num-lanes = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie_clkreqn_cpm>; + status = "okay"; +};
Signature · 1 line
2.25.1
Re: [PATCH 1/4] arm64: dts: rockchip: Sync v5.7-rc1 rk3399pro.dtsi
Quoted 3 lines · Jagan Teki
Sync linux-next v5.7-rc1
rk3399pro.dtsi.Signed-off-by Jagan Teki <[email protected]>
Thanks,
- Kever
Quoted 33 lines
--- arch/arm/dts/rk3399pro.dtsi | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+)create mode 100644
arch/arm/dts/rk3399pro.dtsiarch/arm/dts/rk3399pro.dtsi new file +22
-0@@ -0,0 +1,22 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd. + +#include "rk3399.dtsi" + +/ { + compatible = "rockchip,rk3399pro"; +}; + +/* Default to enabled since AP talk to NPU part over pcie */ +&pcie_phy { + status = "okay"; +}; + +/* Default to enabled since AP talk to NPU part over pcie */ +&pcie0 { + ep-gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>; + num-lanes = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie_clkreqn_cpm>; + status = "okay"; +};
PATCH 2/4 arm64: dts: rockchip: Sync v5.7-rc1 VMARC RK3399Pro SOM
In reply to a message not in the archiveVMARC RK3399Pro SOM is a standard SMARC SOM design with Rockchip RK3399Pro SoC, which is designed by Vamrs.
Specification:
- Rockchip RK3399Pro
- PMIC: RK809-3
- SD slot, 16GiB eMMC
- 2xUSB-2.0, 1xUSB3.0
- USB-C for power supply
- Ethernet, PCIe
- HDMI, MIPI-DSI/CSI, eDP
Add initial support for VMARC RK3399Pro SOM, this would use with associated carrier board.
Sync this dtsi from linux-next v5.7-rc1.
--- arch/arm/dts/rk3399pro-vmarc-som.dtsi | 333 ++++++++++++++++++++++++++ 1 file changed, 333 insertions(+) create mode 100644 arch/arm/dts/rk3399pro-vmarc-som.dtsi
arch/arm/dts/rk3399pro-vmarc-som.dtsi new file +333 -0
@@ -0,0 +1,333 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd + * Copyright (c) 2019 Vamrs Limited + * Copyright (c) 2019 Amarula Solutions(India) + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/rockchip.h> +#include <dt-bindings/pwm/pwm.h> + +/ { + compatible = "vamrs,rk3399pro-vmarc-som", "rockchip,rk3399pro"; + + clkin_gmac: external-gmac-clock { + compatible = "fixed-clock"; + clock-frequency = <125000000>; + clock-output-names = "clkin_gmac"; + #clock-cells = <0>; + }; + + vcc12v_dcin: vcc12v-dcin-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc12v_dcin"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + }; + + vcc5v0_sys: vcc5v0-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc12v_dcin>; + }; +}; + +&cpu_l0 { + cpu-supply = <&vdd_cpu_l>; +}; + +&cpu_l1 { + cpu-supply = <&vdd_cpu_l>; +}; + +&cpu_l2 { + cpu-supply = <&vdd_cpu_l>; +}; + +&cpu_l3 { + cpu-supply = <&vdd_cpu_l>; +}; + +&emmc_phy { + status = "okay"; +}; + +&gmac { + assigned-clocks = <&cru SCLK_RMII_SRC>; + assigned-clock-parents = <&clkin_gmac>; + clock_in_out = "input"; + phy-supply = <&vcc_lan>; + phy-mode = "rgmii"; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>; + snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 50000>; + tx_delay = <0x28>; + rx_delay = <0x11>; +}; + +&i2c0 { + clock-frequency = <400000>; + i2c-scl-rising-time-ns = <180>; + i2c-scl-falling-time-ns = <30>; + status = "okay"; + + rk809: pmic@20 { + compatible = "rockchip,rk809"; + reg = <0x20>; + interrupt-parent = <&gpio1>; + interrupts = <RK_PC2 IRQ_TYPE_LEVEL_LOW>; + #clock-cells = <1>; + clock-output-names = "rk808-clkout1", "rk808-clkout2"; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int_l>; + rockchip,system-power-controller; + wakeup-source; + + vcc1-supply = <&vcc5v0_sys>; + vcc2-supply = <&vcc5v0_sys>; + vcc3-supply = <&vcc5v0_sys>; + vcc4-supply = <&vcc5v0_sys>; + vcc5-supply = <&vcc_buck5>; + vcc6-supply = <&vcc_buck5>; + vcc7-supply = <&vcc5v0_sys>; + vcc8-supply = <&vcc3v3_sys>; + vcc9-supply = <&vcc5v0_sys>; + + regulators { + vdd_log: DCDC_REG1 { + regulator-name = "vdd_log"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1350000>; + regulator-initial-mode = <0x2>; + regulator-state-mem { + regulator-off-in-suspend; + regulator-suspend-microvolt = <900000>; + }; + }; + + vdd_cpu_l: DCDC_REG2 { + regulator-name = "vdd_cpu_l"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <6001>; + regulator-initial-mode = <0x2>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_ddr: DCDC_REG3 { + regulator-name = "vcc_ddr"; + regulator-always-on; + regulator-boot-on; + regulator-initial-mode = <0x2>; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc3v3_sys: DCDC_REG4 { + regulator-name = "vcc3v3_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-initial-mode = <0x2>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcc_buck5: DCDC_REG5 { + regulator-name = "vcc_buck5"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <2200000>; + }; + }; + + vcca_0v9: LDO_REG1 { + regulator-name = "vcca_0v9"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_1v8: LDO_REG2 { + regulator-name = "vcc_1v8"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vcc_0v9: LDO_REG3 { + regulator-name = "vcc_0v9"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <900000>; + }; + }; + + vcca_1v8: LDO_REG4 { + regulator-name = "vcca_1v8"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <1850000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + /* + * As per BSP, but schematic not showing any regulator + * pin for LD05. + */ + vdd1v5_dvp: LDO_REG5 { + regulator-name = "vdd1v5_dvp"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_1v5: LDO_REG6 { + regulator-name = "vcc_1v5"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vccio_3v0: LDO_REG7 { + regulator-name = "vccio_3v0"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vccio_sd: LDO_REG8 { + regulator-name = "vccio_sd"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + /* + * As per BSP, but schematic not showing any regulator + * pin for LD09. + */ + vcc_sd: LDO_REG9 { + regulator-name = "vcc_sd"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc5v0_usb2: SWITCH_REG1 { + regulator-name = "vcc5v0_usb2"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <5000000>; + }; + }; + + vccio_3v3: vcc_lan: SWITCH_REG2 { + regulator-name = "vccio_3v3"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + }; + }; +}; + +&io_domains { + status = "okay"; + bt656-supply = <&vcca_1v8>; + sdmmc-supply = <&vccio_sd>; + gpio1830-supply = <&vccio_3v0>; +}; + +&pmu_io_domains { + status = "okay"; + pmu1830-supply = <&vcc_1v8>; +}; + +&sdhci { + bus-width = <8>; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + non-removable; + status = "okay"; +}; + +&tsadc { + status = "okay"; + rockchip,hw-tshut-mode = <1>; + rockchip,hw-tshut-polarity = <1>; +}; + +&pinctrl { + pmic { + pmic_int_l: pmic-int-l { + rockchip,pins = + <1 RK_PC2 0 &pcfg_pull_up>; + }; + }; +};
Signature · 1 line
2.25.1
Re: [PATCH 2/4] arm64: dts: rockchip: Sync v5.7-rc1 VMARC RK3399Pro SOM
Quoted 12 lines · Jagan Teki
VMARC RK3399Pro SOM is a standard SMARC SOM design with Rockchip RK3399Pro SoC, which is designed by Vamrs.
Specification:
- Rockchip RK3399Pro
- PMIC: RK809-3
- SD slot, 16GiB eMMC
- 2xUSB-2.0, 1xUSB3.0
- USB-C for power supply
- Ethernet, PCIe
- HDMI, MIPI-DSI/CSI, eDP
Quoted 6 lines
Add initial support for VMARC RK3399Pro SOM, this would use with associated carrier board.
Sync this dtsi from linux-next v5.7-rc1.
Signed-off-by Jagan Teki <[email protected]>
Thanks,
- Kever
Quoted 344 lines
--- arch/arm/dts/rk3399pro-vmarc-som.dtsi | 333 ++++++++++++++++++++++++++ 1 file changed, 333 insertions(+)create mode 100644
arch/arm/dts/rk3399pro-vmarc-som.dtsiarch/arm/dts/rk3399pro-vmarc-som.dtsi new file +333
-0@@ -0,0 +1,333 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd + * Copyright (c) 2019 Vamrs Limited + * Copyright (c) 2019 Amarula Solutions(India) + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/rockchip.h> +#include <dt-bindings/pwm/pwm.h> + +/ { + compatible = "vamrs,rk3399pro-vmarc-som", "rockchip,rk3399pro"; + + clkin_gmac: external-gmac-clock { + compatible = "fixed-clock"; + clock-frequency = <125000000>; + clock-output-names = "clkin_gmac"; + #clock-cells = <0>; + }; + + vcc12v_dcin: vcc12v-dcin-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc12v_dcin"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + }; + + vcc5v0_sys: vcc5v0-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc12v_dcin>; + }; +}; + +&cpu_l0 { + cpu-supply = <&vdd_cpu_l>; +}; + +&cpu_l1 { + cpu-supply = <&vdd_cpu_l>; +}; + +&cpu_l2 { + cpu-supply = <&vdd_cpu_l>; +}; + +&cpu_l3 { + cpu-supply = <&vdd_cpu_l>; +}; + +&emmc_phy { + status = "okay"; +}; + +&gmac { + assigned-clocks = <&cru SCLK_RMII_SRC>; + assigned-clock-parents = <&clkin_gmac>; + clock_in_out = "input"; + phy-supply = <&vcc_lan>; + phy-mode = "rgmii"; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>; + snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 50000>; + tx_delay = <0x28>; + rx_delay = <0x11>; +}; + +&i2c0 { + clock-frequency = <400000>; + i2c-scl-rising-time-ns = <180>; + i2c-scl-falling-time-ns = <30>; + status = "okay"; + + rk809: pmic@20 { + compatible = "rockchip,rk809"; + reg = <0x20>; + interrupt-parent = <&gpio1>; + interrupts = <RK_PC2 IRQ_TYPE_LEVEL_LOW>; + #clock-cells = <1>; + clock-output-names = "rk808-clkout1", "rk808-clkout2"; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int_l>; + rockchip,system-power-controller; + wakeup-source; + + vcc1-supply = <&vcc5v0_sys>; + vcc2-supply = <&vcc5v0_sys>; + vcc3-supply = <&vcc5v0_sys>; + vcc4-supply = <&vcc5v0_sys>; + vcc5-supply = <&vcc_buck5>; + vcc6-supply = <&vcc_buck5>; + vcc7-supply = <&vcc5v0_sys>; + vcc8-supply = <&vcc3v3_sys>; + vcc9-supply = <&vcc5v0_sys>; + + regulators { + vdd_log: DCDC_REG1 { + regulator-name = "vdd_log"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1350000>; + regulator-initial-mode = <0x2>; + regulator-state-mem { + regulator-off-in-suspend; + regulator-suspend-microvolt = <900000>; + }; + }; + + vdd_cpu_l: DCDC_REG2 { + regulator-name = "vdd_cpu_l"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <6001>; + regulator-initial-mode = <0x2>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_ddr: DCDC_REG3 { + regulator-name = "vcc_ddr"; + regulator-always-on; + regulator-boot-on; + regulator-initial-mode = <0x2>; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc3v3_sys: DCDC_REG4 { + regulator-name = "vcc3v3_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-initial-mode = <0x2>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcc_buck5: DCDC_REG5 { + regulator-name = "vcc_buck5"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <2200000>; + }; + }; + + vcca_0v9: LDO_REG1 { + regulator-name = "vcca_0v9"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_1v8: LDO_REG2 { + regulator-name = "vcc_1v8"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vcc_0v9: LDO_REG3 { + regulator-name = "vcc_0v9"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <900000>; + }; + }; + + vcca_1v8: LDO_REG4 { + regulator-name = "vcca_1v8"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <1850000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + /* + * As per BSP, but schematic not showing any regulator + * pin for LD05. + */ + vdd1v5_dvp: LDO_REG5 { + regulator-name = "vdd1v5_dvp"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_1v5: LDO_REG6 { + regulator-name = "vcc_1v5"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vccio_3v0: LDO_REG7 { + regulator-name = "vccio_3v0"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vccio_sd: LDO_REG8 { + regulator-name = "vccio_sd"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + /* + * As per BSP, but schematic not showing any regulator + * pin for LD09. + */ + vcc_sd: LDO_REG9 { + regulator-name = "vcc_sd"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc5v0_usb2: SWITCH_REG1 { + regulator-name = "vcc5v0_usb2"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <5000000>; + }; + }; + + vccio_3v3: vcc_lan: SWITCH_REG2 { + regulator-name = "vccio_3v3"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + }; + }; +}; + +&io_domains { + status = "okay"; + bt656-supply = <&vcca_1v8>; + sdmmc-supply = <&vccio_sd>; + gpio1830-supply = <&vccio_3v0>; +}; + +&pmu_io_domains { + status = "okay"; + pmu1830-supply = <&vcc_1v8>; +}; + +&sdhci { + bus-width = <8>; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + non-removable; + status = "okay"; +}; + +&tsadc { + status = "okay"; + rockchip,hw-tshut-mode = <1>; + rockchip,hw-tshut-polarity = <1>; +}; + +&pinctrl { + pmic { + pmic_int_l: pmic-int-l { + rockchip,pins = + <1 RK_PC2 0 &pcfg_pull_up>; + }; + }; +};
PATCH 3/4 ARM: dts: rockchip: Sync v5.7-rc1 Radxa Dalang Carrier
In reply to a message not in the archiveCarrier board often referred as baseboard. For making complete SBC or any other industrial boards, these carrier boards will be used with associated SOMs.
Radxa has Dalang carrier board which supports on-board peripherals, ports like USB-2.0, USB-3.0, HDMI, MIPI DSI/CSI, eDP, Ethernet, WiFi, PCIe, USB-C, 40-Pin GPIO header and etc.
Right now Dalang carrier board is used with two SBC-variants:
Rock Pi N10 => VMARC RK3399Por SOM + Dalang carrier board Rock Pi N8 => VMARC RK3288 SOM + Dalang carrier board(+codec)
So add this carrier board dtsi as a separate file in ARM directory, so-that the same can reuse it in both rk3288, rk3399pro variants of Rockchip SOMs.
Sync this dtsi from linux-next v5.7-rc1.
--- .../dts/rockchip-radxa-dalang-carrier.dtsi | 81 +++++++++++++++++++ 1 file changed, 81 insertions(+) create mode 100644 arch/arm/dts/rockchip-radxa-dalang-carrier.dtsi
arch/arm/dts/rockchip-radxa-dalang-carrier.dtsi new file +81 -0
@@ -0,0 +1,81 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd + * Copyright (c) 2019 Radxa Limited + * Copyright (c) 2019 Amarula Solutions(India) + */ + +#include <dt-bindings/pwm/pwm.h> + +/ { + chosen { + stdout-path = "serial2:1500000n8"; + }; +}; + +&gmac { + status = "okay"; +}; + +&i2c1 { + status = "okay"; + i2c-scl-rising-time-ns = <140>; + i2c-scl-falling-time-ns = <30>; +}; + +&i2c2 { + status = "okay"; + clock-frequency = <400000>; + + hym8563: hym8563@51 { + compatible = "haoyu,hym8563"; + reg = <0x51>; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "hym8563"; + pinctrl-names = "default"; + pinctrl-0 = <&hym8563_int>; + interrupt-parent = <&gpio4>; + interrupts = <30 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +&pwm0 { + status = "okay"; +}; + +&pwm2 { + status = "okay"; +}; + +&sdmmc { + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>; + disable-wp; + vqmmc-supply = <&vccio_sd>; + max-frequency = <150000000>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>; + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_xfer &uart0_cts>; + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&pinctrl { + hym8563 { + hym8563_int: hym8563-int { + rockchip,pins = + <4 RK_PD6 0 &pcfg_pull_up>; + }; + }; +};
Signature · 1 line
2.25.1
Re: [PATCH 3/4] ARM: dts: rockchip: Sync v5.7-rc1 Radxa Dalang Carrier
Quoted 12 lines · Jagan Teki
Carrier board often referred as baseboard. For making complete SBC or any other industrial boards, these carrier boards will be used with associated SOMs.
Radxa has Dalang carrier board which supports on-board peripherals, ports like USB-2.0, USB-3.0, HDMI, MIPI DSI/CSI, eDP, Ethernet, WiFi, PCIe, USB-C, 40-Pin GPIO header and etc.
Right now Dalang carrier board is used with two SBC-variants:
Rock Pi N10 => VMARC RK3399Por SOM + Dalang carrier board Rock Pi N8 => VMARC RK3288 SOM + Dalang carrier board(+codec)
Quoted 7 lines
So add this carrier board dtsi as a separate file in ARM directory, so-that the same can reuse it in both rk3288, rk3399pro variants of Rockchip SOMs.
Sync this dtsi from linux-next v5.7-rc1.
Signed-off-by Jagan Teki <[email protected]>
Thanks,
- Kever
Quoted 92 lines
--- .../dts/rockchip-radxa-dalang-carrier.dtsi | 81 +++++++++++++++++++ 1 file changed, 81 insertions(+)create mode 100644
arch/arm/dts/rockchip-radxa-dalang-carrier.dtsiarch/arm/dts/rockchip-radxa-dalang-carrier.dtsi new file +81
-0@@ -0,0 +1,81 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd + * Copyright (c) 2019 Radxa Limited + * Copyright (c) 2019 Amarula Solutions(India) + */ + +#include <dt-bindings/pwm/pwm.h> + +/ { + chosen { + stdout-path = "serial2:1500000n8"; + }; +}; + +&gmac { + status = "okay"; +}; + +&i2c1 { + status = "okay"; + i2c-scl-rising-time-ns = <140>; + i2c-scl-falling-time-ns = <30>; +}; + +&i2c2 { + status = "okay"; + clock-frequency = <400000>; + + hym8563: hym8563@51 { + compatible = "haoyu,hym8563"; + reg = <0x51>; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "hym8563"; + pinctrl-names = "default"; + pinctrl-0 = <&hym8563_int>; + interrupt-parent = <&gpio4>; + interrupts = <30 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +&pwm0 { + status = "okay"; +}; + +&pwm2 { + status = "okay"; +}; + +&sdmmc { + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>; + disable-wp; + vqmmc-supply = <&vccio_sd>; + max-frequency = <150000000>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>; + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_xfer &uart0_cts>; + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&pinctrl { + hym8563 { + hym8563_int: hym8563-int { + rockchip,pins = + <4 RK_PD6 0 &pcfg_pull_up>; + }; + }; +};
PATCH 4/4 arm64: dts: rockchip: Add Radxa Rock Pi N10 initial support
In reply to a message not in the archiveRock Pi N10 is a Rockchip RK3399Pro based SBC, which has
- VMARC RK3399Pro SOM (as per SMARC standard) from Vamrs.
- Compatible carrier board from Radxa.
VAMRC RK3399Pro SOM need to mount on top of radxa dalang carrier board for making Rock Pi N10 SBC.
So, add initial support for Rock Pi N10 by including rk3399, rk3399pro vamrc-som and raxda dalang carrier board dtsi files.
rk3399pro-rock-pi-n10.dts was synced from linux-next v5.7-rc1.
Tested
- ROCK PI N10 Model B
- ROCK PI N10 Model C
- Boot from SD
--- arch/arm/dts/Makefile | 3 +- .../arm/dts/rk3399pro-rock-pi-n10-u-boot.dtsi | 7 +++ arch/arm/dts/rk3399pro-rock-pi-n10.dts | 18 ++++++++ arch/arm/dts/rk3399pro-u-boot.dtsi | 6 +++ board/rockchip/evb_rk3399/MAINTAINERS | 6 +++ configs/rock-pi-n10-rk3399pro_defconfig | 46 +++++++++++++++++++ 6 files changed, 85 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/rk3399pro-rock-pi-n10-u-boot.dtsi create mode 100644 arch/arm/dts/rk3399pro-rock-pi-n10.dts create mode 100644 arch/arm/dts/rk3399pro-u-boot.dtsi create mode 100644 configs/rock-pi-n10-rk3399pro_defconfig
arch/arm/dts/Makefile +2 -1
@@ -136,7 +136,8 @@ dtb-$(CONFIG_ROCKCHIP_RK3399) += \ rk3399-roc-pc-mezzanine.dtb \ rk3399-rock-pi-4.dtb \ rk3399-rock960.dtb \ - rk3399-rockpro64.dtb + rk3399-rockpro64.dtb \ + rk3399pro-rock-pi-n10.dtb dtb-$(CONFIG_ROCKCHIP_RV1108) += \ rv1108-elgin-r1.dtb \
arch/arm/dts/rk3399pro-rock-pi-n10-u-boot.dtsi new file +7 -0
@@ -0,0 +1,7 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2019 Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org> + */ + +#include "rk3399pro-u-boot.dtsi" +#include "rk3399-sdram-lpddr3-4GB-1600.dtsi"
arch/arm/dts/rk3399pro-rock-pi-n10.dts new file +18 -0
@@ -0,0 +1,18 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd + * Copyright (c) 2019 Radxa Limited + * Copyright (c) 2019 Amarula Solutions(India) + */ + +/dts-v1/; +#include "rk3399.dtsi" +#include "rk3399-opp.dtsi" +#include "rk3399pro-vmarc-som.dtsi" +#include <rockchip-radxa-dalang-carrier.dtsi> + +/ { + model = "Radxa ROCK Pi N10"; + compatible = "radxa,rockpi-n10", "vamrs,rk3399pro-vmarc-som", + "rockchip,rk3399pro"; +};
arch/arm/dts/rk3399pro-u-boot.dtsi new file +6 -0
@@ -0,0 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2019 Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org> + */ + +#include "rk3399-u-boot.dtsi"
board/rockchip/evb_rk3399/MAINTAINERS +6 -0
@@ -68,3 +68,9 @@ M: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org> S: Maintained F: configs/rock-pi-4-rk3399_defconfig F: arch/arm/dts/rk3399-rock-pi-4-u-boot.dtsi + +ROCK-PI-N10 +M: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org> +S: Maintained +F: configs/rock-pi-n10-rk3399pro_defconfig +F: arch/arm/dts/rk3399pro-rock-pi-n10-u-boot.dtsi
configs/rock-pi-n10-rk3399pro_defconfig new file +46 -0
46 lines not on this page · raw message
Signature · 1 line
2.25.1
Re: [PATCH 4/4] arm64: dts: rockchip: Add Radxa Rock Pi N10 initial support
Quoted 10 lines · Jagan Teki
Rock Pi N10 is a Rockchip RK3399Pro based SBC, which has
- VMARC RK3399Pro SOM (as per SMARC standard) from Vamrs.
- Compatible carrier board from Radxa.VAMRC RK3399Pro SOM need to mount on top of radxa dalang carrier board for making Rock Pi N10 SBC.
So, add initial support for Rock Pi N10 by including rk3399, rk3399pro vamrc-som and raxda dalang carrier board dtsi files.
Quoted 8 lines
rk3399pro-rock-pi-n10.dtswas synced from linux-next v5.7-rc1.Tested
- ROCK PI N10 Model B
- ROCK PI N10 Model C
- Boot from SDSigned-off-by Jagan Teki <[email protected]>
Thanks,
- Kever
Quoted 142 lines
--- arch/arm/dts/Makefile | 3 +- .../arm/dts/rk3399pro-rock-pi-n10-u-boot.dtsi | 7 +++ arch/arm/dts/rk3399pro-rock-pi-n10.dts | 18 ++++++++ arch/arm/dts/rk3399pro-u-boot.dtsi | 6 +++ board/rockchip/evb_rk3399/MAINTAINERS | 6 +++ configs/rock-pi-n10-rk3399pro_defconfig | 46 +++++++++++++++++++ 6 files changed, 85 insertions(+), 1 deletion(-)create mode 100644
arch/arm/dts/rk3399pro-rock-pi-n10-u-boot.dtsicreate mode 100644arch/arm/dts/rk3399pro-rock-pi-n10.dtscreate mode 100644arch/arm/dts/rk3399pro-u-boot.dtsicreate mode 100644 configs/rock-pi-n10-rk3399pro_defconfigarch/arm/dts/Makefile +2
-1@@ -136,7 +136,8 @@ dtb-$(CONFIG_ROCKCHIP_RK3399) += \ rk3399-roc-pc-mezzanine.dtb \ rk3399-rock-pi-4.dtb \ rk3399-rock960.dtb \ - rk3399-rockpro64.dtb + rk3399-rockpro64.dtb \ + rk3399pro-rock-pi-n10.dtb dtb-$(CONFIG_ROCKCHIP_RV1108) += \ rv1108-elgin-r1.dtb \arch/arm/dts/rk3399pro-rock-pi-n10-u-boot.dtsi new file +7
-0@@ -0,0 +1,7 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2019 Jagan Teki <[email protected]> + */ + +#include "rk3399pro-u-boot.dtsi" +#include "rk3399-sdram-lpddr3-4GB-1600.dtsi"arch/arm/dts/rk3399pro-rock-pi-n10.dts new file +18
-0@@ -0,0 +1,18 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd + * Copyright (c) 2019 Radxa Limited + * Copyright (c) 2019 Amarula Solutions(India) + */ + +/dts-v1/; +#include "rk3399.dtsi" +#include "rk3399-opp.dtsi" +#include "rk3399pro-vmarc-som.dtsi" +#include <rockchip-radxa-dalang-carrier.dtsi> + +/ { + model = "Radxa ROCK Pi N10"; + compatible = "radxa,rockpi-n10", "vamrs,rk3399pro-vmarc-som", + "rockchip,rk3399pro"; +};arch/arm/dts/rk3399pro-u-boot.dtsi new file +6
-0@@ -0,0 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2019 Jagan Teki <[email protected]> + */ + +#include "rk3399-u-boot.dtsi"board/rockchip/evb_rk3399/MAINTAINERS +6
-0@@ -68,3 +68,9 @@ M: Jagan Teki <[email protected]> S: Maintained F: configs/rock-pi-4-rk3399_defconfig F: arch/arm/dts/rk3399-rock-pi-4-u-boot.dtsi + +ROCK-PI-N10 +M: Jagan Teki <[email protected]> +S: Maintained +F: configs/rock-pi-n10-rk3399pro_defconfig +F: arch/arm/dts/rk3399pro-rock-pi-n10-u-boot.dtsiconfigs/rock-pi-n10-rk3399pro_defconfig new file +46
-0@@ -0,0 +1,46 @@ +CONFIG_ARM=y +CONFIG_ARCH_ROCKCHIP=y +CONFIG_SYS_TEXT_BASE=0x00200000 +CONFIG_SPL_GPIO_SUPPORT=y +CONFIG_ENV_OFFSET=0x3F8000 +CONFIG_ROCKCHIP_RK3399=y +CONFIG_TARGET_EVB_RK3399=y +CONFIG_NR_DRAM_BANKS=1 +CONFIG_DEBUG_UART_BASE=0xFF1A0000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_DEBUG_UART=y +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399pro-rock-pi-n10.dtb" +CONFIG_MISC_INIT_R=y +CONFIG_DISPLAY_BOARDINFO_LATE=y +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +CONFIG_SPL_STACK_R=y +CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 +CONFIG_TPL=y +CONFIG_CMD_BOOTZ=y +CONFIG_CMD_GPT=y +CONFIG_CMD_MMC=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_TIME=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="rk3399pro-rock-pi-n10" +CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents" +CONFIG_ENV_IS_IN_MMC=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_ROCKCHIP_GPIO=y +CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y +CONFIG_MMC_DW=y +CONFIG_MMC_DW_ROCKCHIP=y +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_ROCKCHIP=y +CONFIG_DM_ETH=y +CONFIG_ETH_DESIGNWARE=y +CONFIG_GMAC_ROCKCHIP=y +CONFIG_PMIC_RK8XX=y +CONFIG_REGULATOR_PWM=y +CONFIG_REGULATOR_RK8XX=y +CONFIG_PWM_ROCKCHIP=y +CONFIG_BAUDRATE=1500000 +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_SYSRESET=y +CONFIG_ERRNO_STR=y