Add support for PinePhone LCD panel
Subsystems (6)
v4 cover Add support for PinePhone LCD panel
This patchset adds support for the LCD panel of PinePhone.
The first 3 patches are for the panel itself, and the last 2 patches are for enabling it on PinePhone.
I've tested this on PinePhone 1.0 and 1.2.
Please take a look.
thank you and regards,
Ondrej Jirman
Changes in v4:
- use ->type from the mode instead of hardcoding (Samuel)
- move init_sequence to ->prepare (Samuel)
- move anti-flicker delay to ->enable, explain it (Samuel)
- add enter_sleep after display_off (Samuel)
- drop ->disable (move code to ->unprepare)
- add ID bytes dumping (Linus)
(I can't test it since allwinner DSI driver has a broken
dcs_read function, and I didn't manage to fix it.)
- document magic bytes (Linus)
- assert reset during powerup
- cleanup powerup timings according to the datasheet
Changes in v3:
- Panel driver renamed to the name of the LCD controller
- Re-organize the driver slightly to more easily support more panels based on the same controller.
- Add patch to enable the touchscreen to complete the LCD support on PinePhone.
- Dropped the "DSI fix" patch (the driver seems to work for me without it)
- Improved brightness levels handling:
- PinePhone 1.0 uses default levels generated by the driver
- On PinePhone 1.1 duty cycles < 20% lead to black screen, so default levels can't be used. Martijn Braam came up with a list of duty cycle values that lead to perception of linear brigtness level <-> light intensity on PinePhone 1.1
- There was some feedback on v2 about this being similar to st7701. It's only similar in name. Most of the "user commands" are different, so I opted to keep this in a new driver instead of creating st770x.
Anyone who likes to check the differences, here are datasheets:
- https://megous.com/dl/tmp/ST7703_DS_v01_20160128.pdf
- https://megous.com/dl/tmp/ST7701.pdf
Changes in v2:
- DT Example fix.
- DT Format fix.
- Raised copyright info to 2020.
- Sort panel operation functions.
- Sort inclusion.
-- For phone owners: --
There's an open question on how to set the backlight brightness values on post 1.0 revision phone, since lower duty cycles (< 10-20%) lead to backlight being black. It would be nice if more people can test the various backlight levels on 1.1 and 1.2 revision with this change in dts:
brightness-levels = <0 1000>;
num-interpolated-steps = <1000>;and report at what brightness level the backlight turns on. So far it seems this has a wide range. Lowest useable duty cycle for me is ~7% on 1.2 and for Martijn ~20% on 1.1.
Icenowy Zheng (4):
dt-bindings: vendor-prefixes: Add Xingbangda
dt-bindings: panel: Add binding for Xingbangda XBD599 panel
drm: panel: Add Xingbangda XBD599 panel (ST7703 controller)
arm64: dts: sun50i-a64-pinephone: Enable LCD support on PinePhone
Ondrej Jirman (1):
arm64: dts: sun50i-a64-pinephone: Add touchscreen support
.../display/panel/sitronix,st7703.yaml | 63 +++ .../devicetree/bindings/vendor-prefixes.yaml | 2 + .../allwinner/sun50i-a64-pinephone-1.1.dts | 19 + .../dts/allwinner/sun50i-a64-pinephone.dtsi | 54 ++ drivers/gpu/drm/panel/Kconfig | 10 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-sitronix-st7703.c | 535 ++++++++++++++++++ 7 files changed, 684 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/sitronix,st7703.yaml create mode 100644 drivers/gpu/drm/panel/panel-sitronix-st7703.c
Signature · 1 line
2.27.0
PATCH v4 1/5 dt-bindings: vendor-prefixes: Add Xingbangda
From: Icenowy Zheng <[email protected]>
Shenzhen Xingbangda Display Technology Co., Ltd is a company which produces LCD modules. It supplies the LCD panels for the PinePhone.
Add the vendor prefix of it.
--- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/vendor-prefixes.yaml +2 -0
@@ -1157,6 +1157,8 @@ patternProperties: description: Xiaomi Technology Co., Ltd. "^xillybus,.*": description: Xillybus Ltd. + "^xingbangda,.*": + description: Shenzhen Xingbangda Display Technology Co., Ltd "^xinpeng,.*": description: Shenzhen Xinpeng Technology Co., Ltd "^xlnx,.*":
Signature · 1 line
2.27.0
PATCH v4 2/5 dt-bindings: panel: Add binding for Xingbangda XBD599 panel
In reply to Ondrej JirmanFrom: Icenowy Zheng <[email protected]>
Xingbangda XBD599 is a 5.99" 720x1440 MIPI-DSI LCD panel. It is based on Sitronix ST7703 LCD controller.
Add its device tree binding.
--- .../display/panel/sitronix,st7703.yaml | 63 +++++++++++++++++++ 1 file changed, 63 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/sitronix,st7703.yaml
Documentation/devicetree/bindings/display/panel/sitronix,st7703.yaml new file +63 -0
@@ -0,0 +1,63 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/sitronix,st7703.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sitronix ST7703 MIPI DSI panel + +maintainers: + - Icenowy Zheng <[email protected]> + - Ondrej Jirman <[email protected]> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + items: + - enum: + - xingbangda,xbd599 + - const: sitronix,st7703 + + reg: + description: DSI virtual channel used by that screen + maxItems: 1 + + vcc-supply: + description: regulator that supplies the VCC voltage + + iovcc-supply: + description: regulator that supplies the IOVCC voltage + + reset-gpios: true + + backlight: true + +required: + - compatible + - reg + - vcc-supply + - iovcc-supply + - reset-gpios + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + dsi { + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "xingbangda,xbd599", "sitronix,st7703"; + reg = <0>; + reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* LCD-RST: PD24 */ + iovcc-supply = <®_dldo2>; + vcc-supply = <®_ldo_io0>; + backlight = <&backlight>; + }; + }; +
Signature · 1 line
2.27.0
PATCH v4 3/5 drm: panel: Add Xingbangda XBD599 panel (ST7703 controller)
In reply to Ondrej JirmanFrom: Icenowy Zheng <[email protected]>
Xingbangda XBD599 is a 5.99" 720x1440 MIPI-DSI IPS LCD panel made by Xingbangda, which is used on PinePhone final assembled phones.
It is based on Sitronix ST7703 LCD controller.
Add support for it.
--- drivers/gpu/drm/panel/Kconfig | 10 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-sitronix-st7703.c | 535 ++++++++++++++++++ 3 files changed, 546 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-sitronix-st7703.c
drivers/gpu/drm/panel/Kconfig +10 -0
@@ -395,6 +395,16 @@ config DRM_PANEL_SITRONIX_ST7701 ST7701 controller for 480X864 LCD panels with MIPI/RGB/SPI system interfaces. +config DRM_PANEL_SITRONIX_ST7703 + tristate "Sitronix ST7703 panel driver" + depends on OF + depends on DRM_MIPI_DSI + depends on BACKLIGHT_CLASS_DEVICE + help + Say Y here if you want to enable support for the Sitronix + ST7703 controller for 720X1440 LCD panels with MIPI/RGB/SPI + system interfaces. + config DRM_PANEL_SITRONIX_ST7789V tristate "Sitronix ST7789V panel" depends on OF && SPI
drivers/gpu/drm/panel/Makefile +1 -0
@@ -41,6 +41,7 @@ obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o obj-$(CONFIG_DRM_PANEL_SHARP_LS037V7DW01) += panel-sharp-ls037v7dw01.o obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7701) += panel-sitronix-st7701.o +obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7703) += panel-sitronix-st7703.o obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o obj-$(CONFIG_DRM_PANEL_SONY_ACX424AKP) += panel-sony-acx424akp.o obj-$(CONFIG_DRM_PANEL_SONY_ACX565AKM) += panel-sony-acx565akm.o
drivers/gpu/drm/panel/panel-sitronix-st7703.c new file +535 -0
535 lines not on this page · raw message
Signature · 1 line
2.27.0
Re: [PATCH v4 3/5] drm: panel: Add Xingbangda XBD599 panel (ST7703 controller)
Hi Ondrej et al.
Quoted 6 lines · Ondrej Jirman
From: Icenowy Zheng <[email protected]>
Xingbangda XBD599 is a 5.99" 720x1440 MIPI-DSI IPS LCD panel made by Xingbangda, which is used on PinePhone final assembled phones.
It is based on Sitronix ST7703 LCD controller.
I am a little late to the game here - so sorry if this has been discussed before.
We already have panel-rocktech-jh057n00900.c which is a panle driver based on st7703.
Why is it we need a new driver?
Would it not be better to have one st7703 driver that suipports both panels?
The driver would need dedicated init functions depending on the panel. But a lot could also be shared.
Sam
Quoted 593 lines
Add support for it.
Signed-off-by Icenowy Zheng <[email protected]>Signed-off-by Ondrej Jirman <[email protected]>--- drivers/gpu/drm/panel/Kconfig | 10 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-sitronix-st7703.c | 535 ++++++++++++++++++ 3 files changed, 546 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-sitronix-st7703.cdrivers/gpu/drm/panel/Kconfig +10
-0@@ -395,6 +395,16 @@ config DRM_PANEL_SITRONIX_ST7701 ST7701 controller for 480X864 LCD panels with MIPI/RGB/SPI system interfaces. +config DRM_PANEL_SITRONIX_ST7703 + tristate "Sitronix ST7703 panel driver" + depends on OF + depends on DRM_MIPI_DSI + depends on BACKLIGHT_CLASS_DEVICE + help + Say Y here if you want to enable support for the Sitronix + ST7703 controller for 720X1440 LCD panels with MIPI/RGB/SPI + system interfaces. + config DRM_PANEL_SITRONIX_ST7789V tristate "Sitronix ST7789V panel" depends on OF && SPIdrivers/gpu/drm/panel/Makefile +1
-0@@ -41,6 +41,7 @@ obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o obj-$(CONFIG_DRM_PANEL_SHARP_LS037V7DW01) += panel-sharp-ls037v7dw01.o obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7701) += panel-sitronix-st7701.o +obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7703) += panel-sitronix-st7703.o obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o obj-$(CONFIG_DRM_PANEL_SONY_ACX424AKP) += panel-sony-acx424akp.o obj-$(CONFIG_DRM_PANEL_SONY_ACX565AKM) += panel-sony-acx565akm.odrivers/gpu/drm/panel/panel-sitronix-st7703.c new file +535
-0@@ -0,0 +1,535 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* DRM driver for Sitronix ST7703 MIPI DSI panel +* +* Copyright (C) 2020 Ondrej Jirman <[email protected]> +* Copyright (C) 2019-2020 Icenowy Zheng <[email protected]> +* +* Based on panel-rocktech-jh057n00900.c, which is: +* Copyright (C) Purism SPC 2019 +*/ + +#include <linux/delay.h> +#include <linux/gpio/consumer.h> +#include <linux/mod_devicetable.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/regulator/consumer.h> + +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_modes.h> +#include <drm/drm_panel.h> +#include <drm/drm_print.h> + +/* Manufacturer specific DCS commands */ +#define ST7703_CMD_SETDISP 0xB2 +#define ST7703_CMD_SETRGBIF 0xB3 +#define ST7703_CMD_SETCYC 0xB4 +#define ST7703_CMD_SETBGP 0xB5 +#define ST7703_CMD_SETVCOM 0xB6 +#define ST7703_CMD_SETOTP 0xB7 +#define ST7703_CMD_SETPOWER_EXT 0xB8 +#define ST7703_CMD_SETEXTC 0xB9 +#define ST7703_CMD_SETMIPI 0xBA +#define ST7703_CMD_SETVDC 0xBC +#define ST7703_CMD_UNK_BF 0xBF +#define ST7703_CMD_SETSCR 0xC0 +#define ST7703_CMD_SETPOWER 0xC1 +#define ST7703_CMD_UNK_C6 0xC6 +#define ST7703_CMD_SETPANEL 0xCC +#define ST7703_CMD_RDID1 0xDA +#define ST7703_CMD_RDID2 0xDB +#define ST7703_CMD_RDID3 0xDC +#define ST7703_CMD_SETGAMMA 0xE0 +#define ST7703_CMD_SETEQ 0xE3 +#define ST7703_CMD_SETGIP1 0xE9 +#define ST7703_CMD_SETGIP2 0xEA + +struct st7703_panel_desc { +const struct drm_display_mode *mode; +unsigned int lanes; +unsigned long flags; +enum mipi_dsi_pixel_format format; +const char *const *supply_names; +unsigned int num_supplies; +}; + +struct st7703 { +struct device *dev; +struct drm_panel panel; +struct gpio_desc *reset_gpio; +struct regulator_bulk_data *supplies; +const struct st7703_panel_desc *desc; +bool prepared; +}; + +static inline struct st7703 *panel_to_st7703 (struct drm_panel *panel) +{ + return container_of(panel, struct st7703, panel); +} + +#define dsi_dcs_write_seq(dsi, cmd, seq...) do { \ + static const u8 d[] = { seq }; \ + int ret; \ + ret = mipi_dsi_dcs_write(dsi, cmd, d, ARRAY_SIZE(d)); \ + if (ret < 0) \ + return ret; \ + } while (0) + + +static int st7703_init_sequence (struct st7703 *ctx) +{ +struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev); +struct device *dev = ctx->dev; + +/* +* Init sequence was supplied by the panel vendor. +*/ + +/* Magic sequence to unlock user commands below. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETEXTC ,0xF1 ,0x12 ,0x83 ); + +dsi_dcs_write_seq (dsi,ST7703_CMD_SETMIPI , +0x33 ,/* VC_main = 0, Lane_Number = 3 (4 lanes) */ +0x81 ,/* DSI_LDO_SEL = 1.7V, RTERM = 90 Ohm */ +0x05 ,/* IHSRX = x6 (Low High Speed driving ability) */ +0xF9 ,/* TX_CLK_SEL = fDSICLK/16 */ +0x0E ,/* HFP_OSC (min. HFP number in DSI mode) */ +0x0E ,/* HBP_OSC (min. HBP number in DSI mode) */ +/* The rest is undocumented in ST7703 datasheet */ +0x20 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 , +0x44 ,0x25 ,0x00 ,0x91 ,0x0a ,0x00 ,0x00 ,0x02 , +0x4F ,0x11 ,0x00 ,0x00 ,0x37 ); + +dsi_dcs_write_seq (dsi,ST7703_CMD_SETPOWER_EXT , +0x25 ,/* PCCS = 2, ECP_DC_DIV = 1/4 HSYNC */ +0x22 ,/* DT = 15ms XDK_ECP = x2 */ +0x20 ,/* PFM_DC_DIV = /1 */ +0x03 /* ECP_SYNC_EN = 1, VGX_SYNC_EN = 1 */ ); + +/* RGB I/F porch timing */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETRGBIF , +0x10 ,/* VBP_RGB_GEN */ +0x10 ,/* VFP_RGB_GEN */ +0x05 ,/* DE_BP_RGB_GEN */ +0x05 ,/* DE_FP_RGB_GEN */ +/* The rest is undocumented in ST7703 datasheet */ +0x03 ,0xFF , +0x00 ,0x00 , +0x00 ,0x00 ); + +/* Source driving settings. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETSCR , +0x73 ,/* N_POPON */ +0x73 ,/* N_NOPON */ +0x50 ,/* I_POPON */ +0x50 ,/* I_NOPON */ +0x00 ,/* SCR[31,24] */ +0xC0 ,/* SCR[23,16] */ +0x08 ,/* SCR[15,8] */ +0x70 ,/* SCR[7,0] */ +0x00 /* Undocumented */ ); + +/* NVDDD_SEL = -1.8V, VDDD_SEL = out of range (possibly 1.9V?) */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETVDC ,0x4E ); + +/* +* SS_PANEL = 1 (reverse scan), GS_PANEL = 0 (normal scan) +* REV_PANEL = 1 (normally black panel), BGR_PANEL = 1 (BGR) +*/ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETPANEL ,0x0B ); + +/* Zig-Zag Type C column inversion. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETCYC ,0x80 ); + +/* Set display resolution. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETDISP , +0xF0 ,/* NL = 240 */ +0x12 ,/* RES_V_LSB = 0, BLK_CON = VSSD, +* RESO_SEL = 720RGB +*/ +0xF0 /* WHITE_GND_EN = 1 (GND), +* WHITE_FRAME_SEL = 7 frames, +* ISC = 0 frames +*/ ); + +dsi_dcs_write_seq (dsi,ST7703_CMD_SETEQ , +0x00 ,/* PNOEQ */ +0x00 ,/* NNOEQ */ +0x0B ,/* PEQGND */ +0x0B ,/* NEQGND */ +0x10 ,/* PEQVCI */ +0x10 ,/* NEQVCI */ +0x00 ,/* PEQVCI1 */ +0x00 ,/* NEQVCI1 */ +0x00 ,/* reserved */ +0x00 ,/* reserved */ +0xFF ,/* reserved */ +0x00 ,/* reserved */ +0xC0 ,/* ESD_DET_DATA_WHITE = 1, ESD_WHITE_EN = 1 */ +0x10 /* SLPIN_OPTION = 1 (no need vsync after sleep-in) +* VEDIO_NO_CHECK_EN = 0 +* ESD_WHITE_GND_EN = 0 +* ESD_DET_TIME_SEL = 0 frames +*/ ); + +/* Undocumented command. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_UNK_C6 ,0x01 ,0x00 ,0xFF ,0xFF ,0x00 ); + +dsi_dcs_write_seq (dsi,ST7703_CMD_SETPOWER , +0x74 ,/* VBTHS, VBTLS: VGH = 17V, VBL = -11V */ +0x00 ,/* FBOFF_VGH = 0, FBOFF_VGL = 0 */ +0x32 ,/* VRP */ +0x32 ,/* VRN */ +0x77 ,/* reserved */ +0xF1 ,/* APS = 1 (small), +* VGL_DET_EN = 1, VGH_DET_EN = 1, +* VGL_TURBO = 1, VGH_TURBO = 1 +*/ +0xFF ,/* VGH1_L_DIV, VGL1_L_DIV (1.5MHz) */ +0xFF ,/* VGH1_R_DIV, VGL1_R_DIV (1.5MHz) */ +0xCC ,/* VGH2_L_DIV, VGL2_L_DIV (2.6MHz) */ +0xCC ,/* VGH2_R_DIV, VGL2_R_DIV (2.6MHz) */ +0x77 ,/* VGH3_L_DIV, VGL3_L_DIV (4.5MHz) */ +0x77 /* VGH3_R_DIV, VGL3_R_DIV (4.5MHz) */ ); + +/* Reference voltage. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETBGP , +0x07 ,/* VREF_SEL = 4.2V */ +0x07 /* NVREF_SEL = 4.2V */ ); + +dsi_dcs_write_seq (dsi,ST7703_CMD_SETVCOM , +0x2C ,/* VCOMDC_F = -0.67V */ +0x2C /* VCOMDC_B = -0.67V */ ); + +/* Undocumented command. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_UNK_BF ,0x02 ,0x11 ,0x00 ); + +/* This command is to set forward GIP timing. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETGIP1 , +0x82 ,0x10 ,0x06 ,0x05 ,0xA2 ,0x0A ,0xA5 ,0x12 , +0x31 ,0x23 ,0x37 ,0x83 ,0x04 ,0xBC ,0x27 ,0x38 , +0x0C ,0x00 ,0x03 ,0x00 ,0x00 ,0x00 ,0x0C ,0x00 , +0x03 ,0x00 ,0x00 ,0x00 ,0x75 ,0x75 ,0x31 ,0x88 , +0x88 ,0x88 ,0x88 ,0x88 ,0x88 ,0x13 ,0x88 ,0x64 , +0x64 ,0x20 ,0x88 ,0x88 ,0x88 ,0x88 ,0x88 ,0x88 , +0x02 ,0x88 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 , +0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ); + +/* This command is to set backward GIP timing. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETGIP2 , +0x02 ,0x21 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 , +0x00 ,0x00 ,0x00 ,0x00 ,0x02 ,0x46 ,0x02 ,0x88 , +0x88 ,0x88 ,0x88 ,0x88 ,0x88 ,0x64 ,0x88 ,0x13 , +0x57 ,0x13 ,0x88 ,0x88 ,0x88 ,0x88 ,0x88 ,0x88 , +0x75 ,0x88 ,0x23 ,0x14 ,0x00 ,0x00 ,0x02 ,0x00 , +0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 , +0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x03 ,0x0A , +0xA5 ,0x00 ,0x00 ,0x00 ,0x00 ); + +/* Adjust the gamma characteristics of the panel. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETGAMMA , +0x00 ,0x09 ,0x0D ,0x23 ,0x27 ,0x3C ,0x41 ,0x35 , +0x07 ,0x0D ,0x0E ,0x12 ,0x13 ,0x10 ,0x12 ,0x12 , +0x18 ,0x00 ,0x09 ,0x0D ,0x23 ,0x27 ,0x3C ,0x41 , +0x35 ,0x07 ,0x0D ,0x0E ,0x12 ,0x13 ,0x10 ,0x12 , +0x12 ,0x18 ); + +DRM_DEV_DEBUG_DRIVER (dev,"Panel init sequence done\n" ); +return 0 ; +} + +static int st7703_read_id (struct st7703 *ctx) +{ +struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev); +u8 id1, id2, id3; +int ret; + + ret =mipi_dsi_dcs_read (dsi,ST7703_CMD_RDID1 , &id1,1 ); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev,"could not read ID1\n" ); +return ret; + } + + ret =mipi_dsi_dcs_read (dsi,ST7703_CMD_RDID2 , &id2,1 ); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev,"could not read ID2\n" ); +return ret; + } + + ret =mipi_dsi_dcs_read (dsi,ST7703_CMD_RDID3 , &id3,1 ); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev,"could not read ID3\n" ); +return ret; + } + +DRM_DEV_INFO (ctx->dev, +"manufacturer: %02x version: %02x driver: %02x\n" , + id1, id2, id3); + +return 0 ; +} + +static int st7703_prepare (struct drm_panel *panel) +{ +struct st7703 *ctx =panel_to_st7703 (panel); +struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev); +int ret; + +if (ctx->prepared) +return 0 ; + +gpiod_set_value_cansleep (ctx->reset_gpio,1 ); + + ret =regulator_bulk_enable (ctx->desc->num_supplies, ctx->supplies); +if (ret) +return ret; + +/* Wait for regulators to stabilize. */ +usleep_range (10000 ,20000 ); + +gpiod_set_value_cansleep (ctx->reset_gpio,0 ); + +/* There needs to be at least 15ms post-reset delay. */ +usleep_range (15000 ,20000 ); + + ret =st7703_read_id (ctx); +if (ret <0 ) + goto err_poweroff; + + ret =st7703_init_sequence (ctx); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev, +"Panel init sequence failed (%d)\n" , ret); + goto err_poweroff; + } + + ret =mipi_dsi_dcs_exit_sleep_mode (dsi); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev, +"Failed to exit sleep mode (%d)\n" , ret); + goto err_poweroff; + } + +msleep (120 ); + + ret =mipi_dsi_dcs_set_display_on (dsi); +if (ret) { +DRM_DEV_ERROR (ctx->dev, +"Failed to turn on the display (%d)\n" , ret); + goto err_poweroff; + } + + ctx->prepared = true; + +return 0 ; + +err_poweroff: +gpiod_set_value_cansleep (ctx->reset_gpio,1 ); +regulator_bulk_disable (ctx->desc->num_supplies, ctx->supplies); +return ret; +} + +static int st7703_enable (struct drm_panel *panel) +{ +/* +* Avoid flicker by waiting for slightly more than 1 +* frame's interval. +*/ +msleep (50 ); + +return 0 ; +} + +static int st7703_unprepare (struct drm_panel *panel) +{ +struct st7703 *ctx =panel_to_st7703 (panel); +struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev); +int ret; + +if (!ctx->prepared) +return 0 ; + + ret =mipi_dsi_dcs_set_display_off (dsi); +if (ret <0 ) +DRM_DEV_ERROR (ctx->dev, +"Failed to turn off the display (%d)\n" , ret); + + ret =mipi_dsi_dcs_enter_sleep_mode (dsi); +if (ret <0 ) +DRM_DEV_ERROR (ctx->dev, +"Failed to enter sleep mode (%d)\n" , ret); + +gpiod_set_value_cansleep (ctx->reset_gpio,1 ); +regulator_bulk_disable (ctx->desc->num_supplies, ctx->supplies); + ctx->prepared = false; + +return 0 ; +} + +static int st7703_get_modes (struct drm_panel *panel, +struct drm_connector *connector) +{ +struct st7703 *ctx =panel_to_st7703 (panel); +struct drm_display_mode *mode; + + mode =drm_mode_duplicate (connector->dev, ctx->desc->mode); +if (!mode) { +DRM_DEV_ERROR (ctx->dev,"Failed to add mode\n" ); +return -ENOMEM ; + } + +drm_mode_set_name (mode); + + connector->display_info.width_mm = mode->width_mm; + connector->display_info.height_mm = mode->height_mm; +drm_mode_probed_add (connector, mode); + +return 1 ; +} + +static const struct drm_panel_funcs st7703_drm_funcs = { + .prepare = st7703_prepare, + .enable = st7703_enable, + .unprepare = st7703_unprepare, + .get_modes = st7703_get_modes, +}; + +static const struct drm_display_mode xbd599_mode = { + .hdisplay =720 , + .hsync_start =720 +40 , + .hsync_end =720 +40 +40 , + .htotal =720 +40 +40 +40 , + .vdisplay =1440 , + .vsync_start =1440 +18 , + .vsync_end =1440 +18 +10 , + .vtotal =1440 +18 +10 +17 , + .vrefresh =60 , + .clock =69000 , + .flags =DRM_MODE_FLAG_NHSYNC |DRM_MODE_FLAG_NVSYNC , + + .width_mm =68 , + .height_mm =136 , + .type =DRM_MODE_TYPE_DRIVER |DRM_MODE_TYPE_PREFERRED , +}; + +static const char *const xbd599_supply_names[] = { +"iovcc" , +"vcc" , +}; + +static const struct st7703_panel_desc xbd599_desc = { + .mode = &xbd599_mode, + .lanes =4 , + .flags =MIPI_DSI_MODE_VIDEO |MIPI_DSI_MODE_VIDEO_SYNC_PULSE , + .format =MIPI_DSI_FMT_RGB888 , + .supply_names = xbd599_supply_names, + .num_supplies =ARRAY_SIZE (xbd599_supply_names), +}; + +static int st7703_probe (struct mipi_dsi_device *dsi) +{ +const struct st7703_panel_desc *desc; +struct device *dev = &dsi->dev; +struct st7703 *ctx; +int i, ret; + + ctx =devm_kzalloc (dev,sizeof (*ctx),GFP_KERNEL ); +if (!ctx) +return -ENOMEM ; + + ctx->dev = dev; + ctx->desc = desc =of_device_get_match_data (dev); + + dsi->mode_flags = desc->flags; + dsi->format = desc->format; + dsi->lanes = desc->lanes; + + ctx->supplies =devm_kcalloc (&dsi->dev, desc->num_supplies, +sizeof (*ctx->supplies), +GFP_KERNEL ); +if (!ctx->supplies) +return -ENOMEM ; + +for (i =0 ; i < desc->num_supplies; i++) + ctx->supplies[i].supply = desc->supply_names[i]; + + ret =devm_regulator_bulk_get (&dsi->dev, desc->num_supplies, + ctx->supplies); +if (ret <0 ) +return ret; + + ctx->reset_gpio =devm_gpiod_get (dev,"reset" ,GPIOD_OUT_LOW ); +if (IS_ERR (ctx->reset_gpio)) { +DRM_DEV_ERROR (dev,"Can't get reset gpio\n" ); +return PTR_ERR (ctx->reset_gpio); + } + +mipi_dsi_set_drvdata (dsi, ctx); + +drm_panel_init (&ctx->panel, &dsi->dev, &st7703_drm_funcs, +DRM_MODE_CONNECTOR_DSI ); + + ret =drm_panel_of_backlight (&ctx->panel); +if (ret) +return ret; + +drm_panel_add (&ctx->panel); + + ret =mipi_dsi_attach (dsi); +if (ret <0 ) { +drm_panel_remove (&ctx->panel); +return ret; + } + +return 0 ; +} + +static void st7703_shutdown (struct mipi_dsi_device *dsi) +{ +struct st7703 *ctx =mipi_dsi_get_drvdata (dsi); +int ret; + + ret =drm_panel_unprepare (&ctx->panel); +if (ret <0 ) +DRM_DEV_ERROR (&dsi->dev, +"Failed to unprepare panel (%d)\n" , ret); +} + +static int st7703_remove (struct mipi_dsi_device *dsi) +{ +struct st7703 *ctx =mipi_dsi_get_drvdata (dsi); +int ret; + +st7703_shutdown (dsi); + + ret =mipi_dsi_detach (dsi); +if (ret <0 ) +DRM_DEV_ERROR (&dsi->dev, +"Failed to detach from DSI host (%d)\n" , ret); + +drm_panel_remove (&ctx->panel); + +return 0 ; +} + +static const struct of_device_id st7703_of_match[] = { + { .compatible ="xingbangda,xbd599" , .data = &xbd599_desc }, + {/* sentinel */ } +}; +MODULE_DEVICE_TABLE (of, st7703_of_match); + +static struct mipi_dsi_driver st7703_driver = { + .probe = st7703_probe, + .remove = st7703_remove, + .shutdown = st7703_shutdown, + .driver = { + .name ="st7703" , + .of_match_table = st7703_of_match, + }, +}; +module_mipi_dsi_driver (st7703_driver); + +MODULE_AUTHOR ("Icenowy Zheng <[email protected]>" ); +MODULE_DESCRIPTION ("DRM driver for Sitronix ST7703 MIPI DSI panel" ); +MODULE_LICENSE ("GPL v2" );Signature · 6 lines
2.27.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v4 3/5] drm: panel: Add Xingbangda XBD599 panel (ST7703 controller)
Quoted 8 lines · Sam Ravnborg
Hi Ondrej et al.
Quoted 5 lines · Ondrej Jirman
From: Icenowy Zheng <[email protected]>
Xingbangda XBD599 is a 5.99" 720x1440 MIPI-DSI IPS LCD panel made by Xingbangda, which is used on PinePhone final assembled phones.
Quoted 7 lines
Quoted 1 line
It is based on Sitronix ST7703 LCD controller.
I am a little late to the game here - so sorry if this has been discussed before.
We already havepanel-rocktech-jh057n00900.cwhich is a panle driver based on st7703.
Why is it we need a new driver?
No reason other than the driver not being named after the controller, so I didn't notice.
Quoted 5 lines
Would it not be better to have one st7703 driver that suipports both panels?
The driver would need dedicated init functions depending on the panel. But a lot could also be shared.
I guess I can move the code there.
regards,
o.
Quoted 595 lines
Sam
Quoted 593 lines
Add support for it.
Signed-off-by Icenowy Zheng <[email protected]>Signed-off-by Ondrej Jirman <[email protected]>--- drivers/gpu/drm/panel/Kconfig | 10 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-sitronix-st7703.c | 535 ++++++++++++++++++ 3 files changed, 546 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-sitronix-st7703.cdrivers/gpu/drm/panel/Kconfig +10
-0@@ -395,6 +395,16 @@ config DRM_PANEL_SITRONIX_ST7701 ST7701 controller for 480X864 LCD panels with MIPI/RGB/SPI system interfaces. +config DRM_PANEL_SITRONIX_ST7703 + tristate "Sitronix ST7703 panel driver" + depends on OF + depends on DRM_MIPI_DSI + depends on BACKLIGHT_CLASS_DEVICE + help + Say Y here if you want to enable support for the Sitronix + ST7703 controller for 720X1440 LCD panels with MIPI/RGB/SPI + system interfaces. + config DRM_PANEL_SITRONIX_ST7789V tristate "Sitronix ST7789V panel" depends on OF && SPIdrivers/gpu/drm/panel/Makefile +1
-0@@ -41,6 +41,7 @@ obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o obj-$(CONFIG_DRM_PANEL_SHARP_LS037V7DW01) += panel-sharp-ls037v7dw01.o obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7701) += panel-sitronix-st7701.o +obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7703) += panel-sitronix-st7703.o obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o obj-$(CONFIG_DRM_PANEL_SONY_ACX424AKP) += panel-sony-acx424akp.o obj-$(CONFIG_DRM_PANEL_SONY_ACX565AKM) += panel-sony-acx565akm.odrivers/gpu/drm/panel/panel-sitronix-st7703.c new file +535
-0@@ -0,0 +1,535 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* DRM driver for Sitronix ST7703 MIPI DSI panel +* +* Copyright (C) 2020 Ondrej Jirman <[email protected]> +* Copyright (C) 2019-2020 Icenowy Zheng <[email protected]> +* +* Based on panel-rocktech-jh057n00900.c, which is: +* Copyright (C) Purism SPC 2019 +*/ + +#include <linux/delay.h> +#include <linux/gpio/consumer.h> +#include <linux/mod_devicetable.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/regulator/consumer.h> + +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_modes.h> +#include <drm/drm_panel.h> +#include <drm/drm_print.h> + +/* Manufacturer specific DCS commands */ +#define ST7703_CMD_SETDISP 0xB2 +#define ST7703_CMD_SETRGBIF 0xB3 +#define ST7703_CMD_SETCYC 0xB4 +#define ST7703_CMD_SETBGP 0xB5 +#define ST7703_CMD_SETVCOM 0xB6 +#define ST7703_CMD_SETOTP 0xB7 +#define ST7703_CMD_SETPOWER_EXT 0xB8 +#define ST7703_CMD_SETEXTC 0xB9 +#define ST7703_CMD_SETMIPI 0xBA +#define ST7703_CMD_SETVDC 0xBC +#define ST7703_CMD_UNK_BF 0xBF +#define ST7703_CMD_SETSCR 0xC0 +#define ST7703_CMD_SETPOWER 0xC1 +#define ST7703_CMD_UNK_C6 0xC6 +#define ST7703_CMD_SETPANEL 0xCC +#define ST7703_CMD_RDID1 0xDA +#define ST7703_CMD_RDID2 0xDB +#define ST7703_CMD_RDID3 0xDC +#define ST7703_CMD_SETGAMMA 0xE0 +#define ST7703_CMD_SETEQ 0xE3 +#define ST7703_CMD_SETGIP1 0xE9 +#define ST7703_CMD_SETGIP2 0xEA + +struct st7703_panel_desc { +const struct drm_display_mode *mode; +unsigned int lanes; +unsigned long flags; +enum mipi_dsi_pixel_format format; +const char *const *supply_names; +unsigned int num_supplies; +}; + +struct st7703 { +struct device *dev; +struct drm_panel panel; +struct gpio_desc *reset_gpio; +struct regulator_bulk_data *supplies; +const struct st7703_panel_desc *desc; +bool prepared; +}; + +static inline struct st7703 *panel_to_st7703 (struct drm_panel *panel) +{ + return container_of(panel, struct st7703, panel); +} + +#define dsi_dcs_write_seq(dsi, cmd, seq...) do { \ + static const u8 d[] = { seq }; \ + int ret; \ + ret = mipi_dsi_dcs_write(dsi, cmd, d, ARRAY_SIZE(d)); \ + if (ret < 0) \ + return ret; \ + } while (0) + + +static int st7703_init_sequence (struct st7703 *ctx) +{ +struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev); +struct device *dev = ctx->dev; + +/* +* Init sequence was supplied by the panel vendor. +*/ + +/* Magic sequence to unlock user commands below. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETEXTC ,0xF1 ,0x12 ,0x83 ); + +dsi_dcs_write_seq (dsi,ST7703_CMD_SETMIPI , +0x33 ,/* VC_main = 0, Lane_Number = 3 (4 lanes) */ +0x81 ,/* DSI_LDO_SEL = 1.7V, RTERM = 90 Ohm */ +0x05 ,/* IHSRX = x6 (Low High Speed driving ability) */ +0xF9 ,/* TX_CLK_SEL = fDSICLK/16 */ +0x0E ,/* HFP_OSC (min. HFP number in DSI mode) */ +0x0E ,/* HBP_OSC (min. HBP number in DSI mode) */ +/* The rest is undocumented in ST7703 datasheet */ +0x20 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 , +0x44 ,0x25 ,0x00 ,0x91 ,0x0a ,0x00 ,0x00 ,0x02 , +0x4F ,0x11 ,0x00 ,0x00 ,0x37 ); + +dsi_dcs_write_seq (dsi,ST7703_CMD_SETPOWER_EXT , +0x25 ,/* PCCS = 2, ECP_DC_DIV = 1/4 HSYNC */ +0x22 ,/* DT = 15ms XDK_ECP = x2 */ +0x20 ,/* PFM_DC_DIV = /1 */ +0x03 /* ECP_SYNC_EN = 1, VGX_SYNC_EN = 1 */ ); + +/* RGB I/F porch timing */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETRGBIF , +0x10 ,/* VBP_RGB_GEN */ +0x10 ,/* VFP_RGB_GEN */ +0x05 ,/* DE_BP_RGB_GEN */ +0x05 ,/* DE_FP_RGB_GEN */ +/* The rest is undocumented in ST7703 datasheet */ +0x03 ,0xFF , +0x00 ,0x00 , +0x00 ,0x00 ); + +/* Source driving settings. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETSCR , +0x73 ,/* N_POPON */ +0x73 ,/* N_NOPON */ +0x50 ,/* I_POPON */ +0x50 ,/* I_NOPON */ +0x00 ,/* SCR[31,24] */ +0xC0 ,/* SCR[23,16] */ +0x08 ,/* SCR[15,8] */ +0x70 ,/* SCR[7,0] */ +0x00 /* Undocumented */ ); + +/* NVDDD_SEL = -1.8V, VDDD_SEL = out of range (possibly 1.9V?) */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETVDC ,0x4E ); + +/* +* SS_PANEL = 1 (reverse scan), GS_PANEL = 0 (normal scan) +* REV_PANEL = 1 (normally black panel), BGR_PANEL = 1 (BGR) +*/ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETPANEL ,0x0B ); + +/* Zig-Zag Type C column inversion. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETCYC ,0x80 ); + +/* Set display resolution. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETDISP , +0xF0 ,/* NL = 240 */ +0x12 ,/* RES_V_LSB = 0, BLK_CON = VSSD, +* RESO_SEL = 720RGB +*/ +0xF0 /* WHITE_GND_EN = 1 (GND), +* WHITE_FRAME_SEL = 7 frames, +* ISC = 0 frames +*/ ); + +dsi_dcs_write_seq (dsi,ST7703_CMD_SETEQ , +0x00 ,/* PNOEQ */ +0x00 ,/* NNOEQ */ +0x0B ,/* PEQGND */ +0x0B ,/* NEQGND */ +0x10 ,/* PEQVCI */ +0x10 ,/* NEQVCI */ +0x00 ,/* PEQVCI1 */ +0x00 ,/* NEQVCI1 */ +0x00 ,/* reserved */ +0x00 ,/* reserved */ +0xFF ,/* reserved */ +0x00 ,/* reserved */ +0xC0 ,/* ESD_DET_DATA_WHITE = 1, ESD_WHITE_EN = 1 */ +0x10 /* SLPIN_OPTION = 1 (no need vsync after sleep-in) +* VEDIO_NO_CHECK_EN = 0 +* ESD_WHITE_GND_EN = 0 +* ESD_DET_TIME_SEL = 0 frames +*/ ); + +/* Undocumented command. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_UNK_C6 ,0x01 ,0x00 ,0xFF ,0xFF ,0x00 ); + +dsi_dcs_write_seq (dsi,ST7703_CMD_SETPOWER , +0x74 ,/* VBTHS, VBTLS: VGH = 17V, VBL = -11V */ +0x00 ,/* FBOFF_VGH = 0, FBOFF_VGL = 0 */ +0x32 ,/* VRP */ +0x32 ,/* VRN */ +0x77 ,/* reserved */ +0xF1 ,/* APS = 1 (small), +* VGL_DET_EN = 1, VGH_DET_EN = 1, +* VGL_TURBO = 1, VGH_TURBO = 1 +*/ +0xFF ,/* VGH1_L_DIV, VGL1_L_DIV (1.5MHz) */ +0xFF ,/* VGH1_R_DIV, VGL1_R_DIV (1.5MHz) */ +0xCC ,/* VGH2_L_DIV, VGL2_L_DIV (2.6MHz) */ +0xCC ,/* VGH2_R_DIV, VGL2_R_DIV (2.6MHz) */ +0x77 ,/* VGH3_L_DIV, VGL3_L_DIV (4.5MHz) */ +0x77 /* VGH3_R_DIV, VGL3_R_DIV (4.5MHz) */ ); + +/* Reference voltage. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETBGP , +0x07 ,/* VREF_SEL = 4.2V */ +0x07 /* NVREF_SEL = 4.2V */ ); + +dsi_dcs_write_seq (dsi,ST7703_CMD_SETVCOM , +0x2C ,/* VCOMDC_F = -0.67V */ +0x2C /* VCOMDC_B = -0.67V */ ); + +/* Undocumented command. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_UNK_BF ,0x02 ,0x11 ,0x00 ); + +/* This command is to set forward GIP timing. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETGIP1 , +0x82 ,0x10 ,0x06 ,0x05 ,0xA2 ,0x0A ,0xA5 ,0x12 , +0x31 ,0x23 ,0x37 ,0x83 ,0x04 ,0xBC ,0x27 ,0x38 , +0x0C ,0x00 ,0x03 ,0x00 ,0x00 ,0x00 ,0x0C ,0x00 , +0x03 ,0x00 ,0x00 ,0x00 ,0x75 ,0x75 ,0x31 ,0x88 , +0x88 ,0x88 ,0x88 ,0x88 ,0x88 ,0x13 ,0x88 ,0x64 , +0x64 ,0x20 ,0x88 ,0x88 ,0x88 ,0x88 ,0x88 ,0x88 , +0x02 ,0x88 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 , +0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ); + +/* This command is to set backward GIP timing. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETGIP2 , +0x02 ,0x21 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 , +0x00 ,0x00 ,0x00 ,0x00 ,0x02 ,0x46 ,0x02 ,0x88 , +0x88 ,0x88 ,0x88 ,0x88 ,0x88 ,0x64 ,0x88 ,0x13 , +0x57 ,0x13 ,0x88 ,0x88 ,0x88 ,0x88 ,0x88 ,0x88 , +0x75 ,0x88 ,0x23 ,0x14 ,0x00 ,0x00 ,0x02 ,0x00 , +0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 , +0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x03 ,0x0A , +0xA5 ,0x00 ,0x00 ,0x00 ,0x00 ); + +/* Adjust the gamma characteristics of the panel. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETGAMMA , +0x00 ,0x09 ,0x0D ,0x23 ,0x27 ,0x3C ,0x41 ,0x35 , +0x07 ,0x0D ,0x0E ,0x12 ,0x13 ,0x10 ,0x12 ,0x12 , +0x18 ,0x00 ,0x09 ,0x0D ,0x23 ,0x27 ,0x3C ,0x41 , +0x35 ,0x07 ,0x0D ,0x0E ,0x12 ,0x13 ,0x10 ,0x12 , +0x12 ,0x18 ); + +DRM_DEV_DEBUG_DRIVER (dev,"Panel init sequence done\n" ); +return 0 ; +} + +static int st7703_read_id (struct st7703 *ctx) +{ +struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev); +u8 id1, id2, id3; +int ret; + + ret =mipi_dsi_dcs_read (dsi,ST7703_CMD_RDID1 , &id1,1 ); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev,"could not read ID1\n" ); +return ret; + } + + ret =mipi_dsi_dcs_read (dsi,ST7703_CMD_RDID2 , &id2,1 ); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev,"could not read ID2\n" ); +return ret; + } + + ret =mipi_dsi_dcs_read (dsi,ST7703_CMD_RDID3 , &id3,1 ); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev,"could not read ID3\n" ); +return ret; + } + +DRM_DEV_INFO (ctx->dev, +"manufacturer: %02x version: %02x driver: %02x\n" , + id1, id2, id3); + +return 0 ; +} + +static int st7703_prepare (struct drm_panel *panel) +{ +struct st7703 *ctx =panel_to_st7703 (panel); +struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev); +int ret; + +if (ctx->prepared) +return 0 ; + +gpiod_set_value_cansleep (ctx->reset_gpio,1 ); + + ret =regulator_bulk_enable (ctx->desc->num_supplies, ctx->supplies); +if (ret) +return ret; + +/* Wait for regulators to stabilize. */ +usleep_range (10000 ,20000 ); + +gpiod_set_value_cansleep (ctx->reset_gpio,0 ); + +/* There needs to be at least 15ms post-reset delay. */ +usleep_range (15000 ,20000 ); + + ret =st7703_read_id (ctx); +if (ret <0 ) + goto err_poweroff; + + ret =st7703_init_sequence (ctx); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev, +"Panel init sequence failed (%d)\n" , ret); + goto err_poweroff; + } + + ret =mipi_dsi_dcs_exit_sleep_mode (dsi); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev, +"Failed to exit sleep mode (%d)\n" , ret); + goto err_poweroff; + } + +msleep (120 ); + + ret =mipi_dsi_dcs_set_display_on (dsi); +if (ret) { +DRM_DEV_ERROR (ctx->dev, +"Failed to turn on the display (%d)\n" , ret); + goto err_poweroff; + } + + ctx->prepared = true; + +return 0 ; + +err_poweroff: +gpiod_set_value_cansleep (ctx->reset_gpio,1 ); +regulator_bulk_disable (ctx->desc->num_supplies, ctx->supplies); +return ret; +} + +static int st7703_enable (struct drm_panel *panel) +{ +/* +* Avoid flicker by waiting for slightly more than 1 +* frame's interval. +*/ +msleep (50 ); + +return 0 ; +} + +static int st7703_unprepare (struct drm_panel *panel) +{ +struct st7703 *ctx =panel_to_st7703 (panel); +struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev); +int ret; + +if (!ctx->prepared) +return 0 ; + + ret =mipi_dsi_dcs_set_display_off (dsi); +if (ret <0 ) +DRM_DEV_ERROR (ctx->dev, +"Failed to turn off the display (%d)\n" , ret); + + ret =mipi_dsi_dcs_enter_sleep_mode (dsi); +if (ret <0 ) +DRM_DEV_ERROR (ctx->dev, +"Failed to enter sleep mode (%d)\n" , ret); + +gpiod_set_value_cansleep (ctx->reset_gpio,1 ); +regulator_bulk_disable (ctx->desc->num_supplies, ctx->supplies); + ctx->prepared = false; + +return 0 ; +} + +static int st7703_get_modes (struct drm_panel *panel, +struct drm_connector *connector) +{ +struct st7703 *ctx =panel_to_st7703 (panel); +struct drm_display_mode *mode; + + mode =drm_mode_duplicate (connector->dev, ctx->desc->mode); +if (!mode) { +DRM_DEV_ERROR (ctx->dev,"Failed to add mode\n" ); +return -ENOMEM ; + } + +drm_mode_set_name (mode); + + connector->display_info.width_mm = mode->width_mm; + connector->display_info.height_mm = mode->height_mm; +drm_mode_probed_add (connector, mode); + +return 1 ; +} + +static const struct drm_panel_funcs st7703_drm_funcs = { + .prepare = st7703_prepare, + .enable = st7703_enable, + .unprepare = st7703_unprepare, + .get_modes = st7703_get_modes, +}; + +static const struct drm_display_mode xbd599_mode = { + .hdisplay =720 , + .hsync_start =720 +40 , + .hsync_end =720 +40 +40 , + .htotal =720 +40 +40 +40 , + .vdisplay =1440 , + .vsync_start =1440 +18 , + .vsync_end =1440 +18 +10 , + .vtotal =1440 +18 +10 +17 , + .vrefresh =60 , + .clock =69000 , + .flags =DRM_MODE_FLAG_NHSYNC |DRM_MODE_FLAG_NVSYNC , + + .width_mm =68 , + .height_mm =136 , + .type =DRM_MODE_TYPE_DRIVER |DRM_MODE_TYPE_PREFERRED , +}; + +static const char *const xbd599_supply_names[] = { +"iovcc" , +"vcc" , +}; + +static const struct st7703_panel_desc xbd599_desc = { + .mode = &xbd599_mode, + .lanes =4 , + .flags =MIPI_DSI_MODE_VIDEO |MIPI_DSI_MODE_VIDEO_SYNC_PULSE , + .format =MIPI_DSI_FMT_RGB888 , + .supply_names = xbd599_supply_names, + .num_supplies =ARRAY_SIZE (xbd599_supply_names), +}; + +static int st7703_probe (struct mipi_dsi_device *dsi) +{ +const struct st7703_panel_desc *desc; +struct device *dev = &dsi->dev; +struct st7703 *ctx; +int i, ret; + + ctx =devm_kzalloc (dev,sizeof (*ctx),GFP_KERNEL ); +if (!ctx) +return -ENOMEM ; + + ctx->dev = dev; + ctx->desc = desc =of_device_get_match_data (dev); + + dsi->mode_flags = desc->flags; + dsi->format = desc->format; + dsi->lanes = desc->lanes; + + ctx->supplies =devm_kcalloc (&dsi->dev, desc->num_supplies, +sizeof (*ctx->supplies), +GFP_KERNEL ); +if (!ctx->supplies) +return -ENOMEM ; + +for (i =0 ; i < desc->num_supplies; i++) + ctx->supplies[i].supply = desc->supply_names[i]; + + ret =devm_regulator_bulk_get (&dsi->dev, desc->num_supplies, + ctx->supplies); +if (ret <0 ) +return ret; + + ctx->reset_gpio =devm_gpiod_get (dev,"reset" ,GPIOD_OUT_LOW ); +if (IS_ERR (ctx->reset_gpio)) { +DRM_DEV_ERROR (dev,"Can't get reset gpio\n" ); +return PTR_ERR (ctx->reset_gpio); + } + +mipi_dsi_set_drvdata (dsi, ctx); + +drm_panel_init (&ctx->panel, &dsi->dev, &st7703_drm_funcs, +DRM_MODE_CONNECTOR_DSI ); + + ret =drm_panel_of_backlight (&ctx->panel); +if (ret) +return ret; + +drm_panel_add (&ctx->panel); + + ret =mipi_dsi_attach (dsi); +if (ret <0 ) { +drm_panel_remove (&ctx->panel); +return ret; + } + +return 0 ; +} + +static void st7703_shutdown (struct mipi_dsi_device *dsi) +{ +struct st7703 *ctx =mipi_dsi_get_drvdata (dsi); +int ret; + + ret =drm_panel_unprepare (&ctx->panel); +if (ret <0 ) +DRM_DEV_ERROR (&dsi->dev, +"Failed to unprepare panel (%d)\n" , ret); +} + +static int st7703_remove (struct mipi_dsi_device *dsi) +{ +struct st7703 *ctx =mipi_dsi_get_drvdata (dsi); +int ret; + +st7703_shutdown (dsi); + + ret =mipi_dsi_detach (dsi); +if (ret <0 ) +DRM_DEV_ERROR (&dsi->dev, +"Failed to detach from DSI host (%d)\n" , ret); + +drm_panel_remove (&ctx->panel); + +return 0 ; +} + +static const struct of_device_id st7703_of_match[] = { + { .compatible ="xingbangda,xbd599" , .data = &xbd599_desc }, + {/* sentinel */ } +}; +MODULE_DEVICE_TABLE (of, st7703_of_match); + +static struct mipi_dsi_driver st7703_driver = { + .probe = st7703_probe, + .remove = st7703_remove, + .shutdown = st7703_shutdown, + .driver = { + .name ="st7703" , + .of_match_table = st7703_of_match, + }, +}; +module_mipi_dsi_driver (st7703_driver); + +MODULE_AUTHOR ("Icenowy Zheng <[email protected]>" ); +MODULE_DESCRIPTION ("DRM driver for Sitronix ST7703 MIPI DSI panel" ); +MODULE_LICENSE ("GPL v2" );Signature · 6 lines
2.27.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v4 3/5] drm: panel: Add Xingbangda XBD599 panel (ST7703 controller)
Quoted 20 lines · Ondřej Jirman
Quoted 8 lines · Sam Ravnborg
Hi Ondrej et al.
Quoted 5 lines · Ondrej Jirman
From: Icenowy Zheng <[email protected]>
Xingbangda XBD599 is a 5.99" 720x1440 MIPI-DSI IPS LCD panel made by Xingbangda, which is used on PinePhone final assembled phones.
Quoted 7 lines
Quoted 1 line
It is based on Sitronix ST7703 LCD controller.
I am a little late to the game here - so sorry if this has been discussed before.
We already havepanel-rocktech-jh057n00900.cwhich is a panle driver based on st7703.
Why is it we need a new driver?No reason other than the driver not being named after the controller, so I didn't notice.
Quoted 7 lines
Quoted 5 lines
Would it not be better to have one st7703 driver that suipports both panels?
The driver would need dedicated init functions depending on the panel. But a lot could also be shared.
I guess I can move the code there.
In the same process the river should then be renamed to follow other sitronix based drivers.
So the next developer will recognize this and use the correct driver.
Sam
Quoted 595 lines
regards,
o.Quoted 591 lines
Sam
Quoted 589 lines
Add support for it.
Signed-off-by Icenowy Zheng <[email protected]>Signed-off-by Ondrej Jirman <[email protected]>--- drivers/gpu/drm/panel/Kconfig | 10 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-sitronix-st7703.c | 535 ++++++++++++++++++ 3 files changed, 546 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-sitronix-st7703.cdrivers/gpu/drm/panel/Kconfig +10
-0@@ -395,6 +395,16 @@ config DRM_PANEL_SITRONIX_ST7701 ST7701 controller for 480X864 LCD panels with MIPI/RGB/SPI system interfaces. +config DRM_PANEL_SITRONIX_ST7703 + tristate "Sitronix ST7703 panel driver" + depends on OF + depends on DRM_MIPI_DSI + depends on BACKLIGHT_CLASS_DEVICE + help + Say Y here if you want to enable support for the Sitronix + ST7703 controller for 720X1440 LCD panels with MIPI/RGB/SPI + system interfaces. + config DRM_PANEL_SITRONIX_ST7789V tristate "Sitronix ST7789V panel" depends on OF && SPIdrivers/gpu/drm/panel/Makefile +1
-0@@ -41,6 +41,7 @@ obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o obj-$(CONFIG_DRM_PANEL_SHARP_LS037V7DW01) += panel-sharp-ls037v7dw01.o obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7701) += panel-sitronix-st7701.o +obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7703) += panel-sitronix-st7703.o obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o obj-$(CONFIG_DRM_PANEL_SONY_ACX424AKP) += panel-sony-acx424akp.o obj-$(CONFIG_DRM_PANEL_SONY_ACX565AKM) += panel-sony-acx565akm.odrivers/gpu/drm/panel/panel-sitronix-st7703.c new file +535
-0@@ -0,0 +1,535 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* DRM driver for Sitronix ST7703 MIPI DSI panel +* +* Copyright (C) 2020 Ondrej Jirman <[email protected]> +* Copyright (C) 2019-2020 Icenowy Zheng <[email protected]> +* +* Based on panel-rocktech-jh057n00900.c, which is: +* Copyright (C) Purism SPC 2019 +*/ + +#include <linux/delay.h> +#include <linux/gpio/consumer.h> +#include <linux/mod_devicetable.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/regulator/consumer.h> + +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_modes.h> +#include <drm/drm_panel.h> +#include <drm/drm_print.h> + +/* Manufacturer specific DCS commands */ +#define ST7703_CMD_SETDISP 0xB2 +#define ST7703_CMD_SETRGBIF 0xB3 +#define ST7703_CMD_SETCYC 0xB4 +#define ST7703_CMD_SETBGP 0xB5 +#define ST7703_CMD_SETVCOM 0xB6 +#define ST7703_CMD_SETOTP 0xB7 +#define ST7703_CMD_SETPOWER_EXT 0xB8 +#define ST7703_CMD_SETEXTC 0xB9 +#define ST7703_CMD_SETMIPI 0xBA +#define ST7703_CMD_SETVDC 0xBC +#define ST7703_CMD_UNK_BF 0xBF +#define ST7703_CMD_SETSCR 0xC0 +#define ST7703_CMD_SETPOWER 0xC1 +#define ST7703_CMD_UNK_C6 0xC6 +#define ST7703_CMD_SETPANEL 0xCC +#define ST7703_CMD_RDID1 0xDA +#define ST7703_CMD_RDID2 0xDB +#define ST7703_CMD_RDID3 0xDC +#define ST7703_CMD_SETGAMMA 0xE0 +#define ST7703_CMD_SETEQ 0xE3 +#define ST7703_CMD_SETGIP1 0xE9 +#define ST7703_CMD_SETGIP2 0xEA + +struct st7703_panel_desc { +const struct drm_display_mode *mode; +unsigned int lanes; +unsigned long flags; +enum mipi_dsi_pixel_format format; +const char *const *supply_names; +unsigned int num_supplies; +}; + +struct st7703 { +struct device *dev; +struct drm_panel panel; +struct gpio_desc *reset_gpio; +struct regulator_bulk_data *supplies; +const struct st7703_panel_desc *desc; +bool prepared; +}; + +static inline struct st7703 *panel_to_st7703 (struct drm_panel *panel) +{ + return container_of(panel, struct st7703, panel); +} + +#define dsi_dcs_write_seq(dsi, cmd, seq...) do { \ + static const u8 d[] = { seq }; \ + int ret; \ + ret = mipi_dsi_dcs_write(dsi, cmd, d, ARRAY_SIZE(d)); \ + if (ret < 0) \ + return ret; \ + } while (0) + + +static int st7703_init_sequence (struct st7703 *ctx) +{ +struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev); +struct device *dev = ctx->dev; + +/* +* Init sequence was supplied by the panel vendor. +*/ + +/* Magic sequence to unlock user commands below. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETEXTC ,0xF1 ,0x12 ,0x83 ); + +dsi_dcs_write_seq (dsi,ST7703_CMD_SETMIPI , +0x33 ,/* VC_main = 0, Lane_Number = 3 (4 lanes) */ +0x81 ,/* DSI_LDO_SEL = 1.7V, RTERM = 90 Ohm */ +0x05 ,/* IHSRX = x6 (Low High Speed driving ability) */ +0xF9 ,/* TX_CLK_SEL = fDSICLK/16 */ +0x0E ,/* HFP_OSC (min. HFP number in DSI mode) */ +0x0E ,/* HBP_OSC (min. HBP number in DSI mode) */ +/* The rest is undocumented in ST7703 datasheet */ +0x20 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 , +0x44 ,0x25 ,0x00 ,0x91 ,0x0a ,0x00 ,0x00 ,0x02 , +0x4F ,0x11 ,0x00 ,0x00 ,0x37 ); + +dsi_dcs_write_seq (dsi,ST7703_CMD_SETPOWER_EXT , +0x25 ,/* PCCS = 2, ECP_DC_DIV = 1/4 HSYNC */ +0x22 ,/* DT = 15ms XDK_ECP = x2 */ +0x20 ,/* PFM_DC_DIV = /1 */ +0x03 /* ECP_SYNC_EN = 1, VGX_SYNC_EN = 1 */ ); + +/* RGB I/F porch timing */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETRGBIF , +0x10 ,/* VBP_RGB_GEN */ +0x10 ,/* VFP_RGB_GEN */ +0x05 ,/* DE_BP_RGB_GEN */ +0x05 ,/* DE_FP_RGB_GEN */ +/* The rest is undocumented in ST7703 datasheet */ +0x03 ,0xFF , +0x00 ,0x00 , +0x00 ,0x00 ); + +/* Source driving settings. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETSCR , +0x73 ,/* N_POPON */ +0x73 ,/* N_NOPON */ +0x50 ,/* I_POPON */ +0x50 ,/* I_NOPON */ +0x00 ,/* SCR[31,24] */ +0xC0 ,/* SCR[23,16] */ +0x08 ,/* SCR[15,8] */ +0x70 ,/* SCR[7,0] */ +0x00 /* Undocumented */ ); + +/* NVDDD_SEL = -1.8V, VDDD_SEL = out of range (possibly 1.9V?) */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETVDC ,0x4E ); + +/* +* SS_PANEL = 1 (reverse scan), GS_PANEL = 0 (normal scan) +* REV_PANEL = 1 (normally black panel), BGR_PANEL = 1 (BGR) +*/ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETPANEL ,0x0B ); + +/* Zig-Zag Type C column inversion. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETCYC ,0x80 ); + +/* Set display resolution. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETDISP , +0xF0 ,/* NL = 240 */ +0x12 ,/* RES_V_LSB = 0, BLK_CON = VSSD, +* RESO_SEL = 720RGB +*/ +0xF0 /* WHITE_GND_EN = 1 (GND), +* WHITE_FRAME_SEL = 7 frames, +* ISC = 0 frames +*/ ); + +dsi_dcs_write_seq (dsi,ST7703_CMD_SETEQ , +0x00 ,/* PNOEQ */ +0x00 ,/* NNOEQ */ +0x0B ,/* PEQGND */ +0x0B ,/* NEQGND */ +0x10 ,/* PEQVCI */ +0x10 ,/* NEQVCI */ +0x00 ,/* PEQVCI1 */ +0x00 ,/* NEQVCI1 */ +0x00 ,/* reserved */ +0x00 ,/* reserved */ +0xFF ,/* reserved */ +0x00 ,/* reserved */ +0xC0 ,/* ESD_DET_DATA_WHITE = 1, ESD_WHITE_EN = 1 */ +0x10 /* SLPIN_OPTION = 1 (no need vsync after sleep-in) +* VEDIO_NO_CHECK_EN = 0 +* ESD_WHITE_GND_EN = 0 +* ESD_DET_TIME_SEL = 0 frames +*/ ); + +/* Undocumented command. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_UNK_C6 ,0x01 ,0x00 ,0xFF ,0xFF ,0x00 ); + +dsi_dcs_write_seq (dsi,ST7703_CMD_SETPOWER , +0x74 ,/* VBTHS, VBTLS: VGH = 17V, VBL = -11V */ +0x00 ,/* FBOFF_VGH = 0, FBOFF_VGL = 0 */ +0x32 ,/* VRP */ +0x32 ,/* VRN */ +0x77 ,/* reserved */ +0xF1 ,/* APS = 1 (small), +* VGL_DET_EN = 1, VGH_DET_EN = 1, +* VGL_TURBO = 1, VGH_TURBO = 1 +*/ +0xFF ,/* VGH1_L_DIV, VGL1_L_DIV (1.5MHz) */ +0xFF ,/* VGH1_R_DIV, VGL1_R_DIV (1.5MHz) */ +0xCC ,/* VGH2_L_DIV, VGL2_L_DIV (2.6MHz) */ +0xCC ,/* VGH2_R_DIV, VGL2_R_DIV (2.6MHz) */ +0x77 ,/* VGH3_L_DIV, VGL3_L_DIV (4.5MHz) */ +0x77 /* VGH3_R_DIV, VGL3_R_DIV (4.5MHz) */ ); + +/* Reference voltage. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETBGP , +0x07 ,/* VREF_SEL = 4.2V */ +0x07 /* NVREF_SEL = 4.2V */ ); + +dsi_dcs_write_seq (dsi,ST7703_CMD_SETVCOM , +0x2C ,/* VCOMDC_F = -0.67V */ +0x2C /* VCOMDC_B = -0.67V */ ); + +/* Undocumented command. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_UNK_BF ,0x02 ,0x11 ,0x00 ); + +/* This command is to set forward GIP timing. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETGIP1 , +0x82 ,0x10 ,0x06 ,0x05 ,0xA2 ,0x0A ,0xA5 ,0x12 , +0x31 ,0x23 ,0x37 ,0x83 ,0x04 ,0xBC ,0x27 ,0x38 , +0x0C ,0x00 ,0x03 ,0x00 ,0x00 ,0x00 ,0x0C ,0x00 , +0x03 ,0x00 ,0x00 ,0x00 ,0x75 ,0x75 ,0x31 ,0x88 , +0x88 ,0x88 ,0x88 ,0x88 ,0x88 ,0x13 ,0x88 ,0x64 , +0x64 ,0x20 ,0x88 ,0x88 ,0x88 ,0x88 ,0x88 ,0x88 , +0x02 ,0x88 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 , +0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ); + +/* This command is to set backward GIP timing. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETGIP2 , +0x02 ,0x21 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 , +0x00 ,0x00 ,0x00 ,0x00 ,0x02 ,0x46 ,0x02 ,0x88 , +0x88 ,0x88 ,0x88 ,0x88 ,0x88 ,0x64 ,0x88 ,0x13 , +0x57 ,0x13 ,0x88 ,0x88 ,0x88 ,0x88 ,0x88 ,0x88 , +0x75 ,0x88 ,0x23 ,0x14 ,0x00 ,0x00 ,0x02 ,0x00 , +0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 , +0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x03 ,0x0A , +0xA5 ,0x00 ,0x00 ,0x00 ,0x00 ); + +/* Adjust the gamma characteristics of the panel. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETGAMMA , +0x00 ,0x09 ,0x0D ,0x23 ,0x27 ,0x3C ,0x41 ,0x35 , +0x07 ,0x0D ,0x0E ,0x12 ,0x13 ,0x10 ,0x12 ,0x12 , +0x18 ,0x00 ,0x09 ,0x0D ,0x23 ,0x27 ,0x3C ,0x41 , +0x35 ,0x07 ,0x0D ,0x0E ,0x12 ,0x13 ,0x10 ,0x12 , +0x12 ,0x18 ); + +DRM_DEV_DEBUG_DRIVER (dev,"Panel init sequence done\n" ); +return 0 ; +} + +static int st7703_read_id (struct st7703 *ctx) +{ +struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev); +u8 id1, id2, id3; +int ret; + + ret =mipi_dsi_dcs_read (dsi,ST7703_CMD_RDID1 , &id1,1 ); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev,"could not read ID1\n" ); +return ret; + } + + ret =mipi_dsi_dcs_read (dsi,ST7703_CMD_RDID2 , &id2,1 ); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev,"could not read ID2\n" ); +return ret; + } + + ret =mipi_dsi_dcs_read (dsi,ST7703_CMD_RDID3 , &id3,1 ); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev,"could not read ID3\n" ); +return ret; + } + +DRM_DEV_INFO (ctx->dev, +"manufacturer: %02x version: %02x driver: %02x\n" , + id1, id2, id3); + +return 0 ; +} + +static int st7703_prepare (struct drm_panel *panel) +{ +struct st7703 *ctx =panel_to_st7703 (panel); +struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev); +int ret; + +if (ctx->prepared) +return 0 ; + +gpiod_set_value_cansleep (ctx->reset_gpio,1 ); + + ret =regulator_bulk_enable (ctx->desc->num_supplies, ctx->supplies); +if (ret) +return ret; + +/* Wait for regulators to stabilize. */ +usleep_range (10000 ,20000 ); + +gpiod_set_value_cansleep (ctx->reset_gpio,0 ); + +/* There needs to be at least 15ms post-reset delay. */ +usleep_range (15000 ,20000 ); + + ret =st7703_read_id (ctx); +if (ret <0 ) + goto err_poweroff; + + ret =st7703_init_sequence (ctx); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev, +"Panel init sequence failed (%d)\n" , ret); + goto err_poweroff; + } + + ret =mipi_dsi_dcs_exit_sleep_mode (dsi); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev, +"Failed to exit sleep mode (%d)\n" , ret); + goto err_poweroff; + } + +msleep (120 ); + + ret =mipi_dsi_dcs_set_display_on (dsi); +if (ret) { +DRM_DEV_ERROR (ctx->dev, +"Failed to turn on the display (%d)\n" , ret); + goto err_poweroff; + } + + ctx->prepared = true; + +return 0 ; + +err_poweroff: +gpiod_set_value_cansleep (ctx->reset_gpio,1 ); +regulator_bulk_disable (ctx->desc->num_supplies, ctx->supplies); +return ret; +} + +static int st7703_enable (struct drm_panel *panel) +{ +/* +* Avoid flicker by waiting for slightly more than 1 +* frame's interval. +*/ +msleep (50 ); + +return 0 ; +} + +static int st7703_unprepare (struct drm_panel *panel) +{ +struct st7703 *ctx =panel_to_st7703 (panel); +struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev); +int ret; + +if (!ctx->prepared) +return 0 ; + + ret =mipi_dsi_dcs_set_display_off (dsi); +if (ret <0 ) +DRM_DEV_ERROR (ctx->dev, +"Failed to turn off the display (%d)\n" , ret); + + ret =mipi_dsi_dcs_enter_sleep_mode (dsi); +if (ret <0 ) +DRM_DEV_ERROR (ctx->dev, +"Failed to enter sleep mode (%d)\n" , ret); + +gpiod_set_value_cansleep (ctx->reset_gpio,1 ); +regulator_bulk_disable (ctx->desc->num_supplies, ctx->supplies); + ctx->prepared = false; + +return 0 ; +} + +static int st7703_get_modes (struct drm_panel *panel, +struct drm_connector *connector) +{ +struct st7703 *ctx =panel_to_st7703 (panel); +struct drm_display_mode *mode; + + mode =drm_mode_duplicate (connector->dev, ctx->desc->mode); +if (!mode) { +DRM_DEV_ERROR (ctx->dev,"Failed to add mode\n" ); +return -ENOMEM ; + } + +drm_mode_set_name (mode); + + connector->display_info.width_mm = mode->width_mm; + connector->display_info.height_mm = mode->height_mm; +drm_mode_probed_add (connector, mode); + +return 1 ; +} + +static const struct drm_panel_funcs st7703_drm_funcs = { + .prepare = st7703_prepare, + .enable = st7703_enable, + .unprepare = st7703_unprepare, + .get_modes = st7703_get_modes, +}; + +static const struct drm_display_mode xbd599_mode = { + .hdisplay =720 , + .hsync_start =720 +40 , + .hsync_end =720 +40 +40 , + .htotal =720 +40 +40 +40 , + .vdisplay =1440 , + .vsync_start =1440 +18 , + .vsync_end =1440 +18 +10 , + .vtotal =1440 +18 +10 +17 , + .vrefresh =60 , + .clock =69000 , + .flags =DRM_MODE_FLAG_NHSYNC |DRM_MODE_FLAG_NVSYNC , + + .width_mm =68 , + .height_mm =136 , + .type =DRM_MODE_TYPE_DRIVER |DRM_MODE_TYPE_PREFERRED , +}; + +static const char *const xbd599_supply_names[] = { +"iovcc" , +"vcc" , +}; + +static const struct st7703_panel_desc xbd599_desc = { + .mode = &xbd599_mode, + .lanes =4 , + .flags =MIPI_DSI_MODE_VIDEO |MIPI_DSI_MODE_VIDEO_SYNC_PULSE , + .format =MIPI_DSI_FMT_RGB888 , + .supply_names = xbd599_supply_names, + .num_supplies =ARRAY_SIZE (xbd599_supply_names), +}; + +static int st7703_probe (struct mipi_dsi_device *dsi) +{ +const struct st7703_panel_desc *desc; +struct device *dev = &dsi->dev; +struct st7703 *ctx; +int i, ret; + + ctx =devm_kzalloc (dev,sizeof (*ctx),GFP_KERNEL ); +if (!ctx) +return -ENOMEM ; + + ctx->dev = dev; + ctx->desc = desc =of_device_get_match_data (dev); + + dsi->mode_flags = desc->flags; + dsi->format = desc->format; + dsi->lanes = desc->lanes; + + ctx->supplies =devm_kcalloc (&dsi->dev, desc->num_supplies, +sizeof (*ctx->supplies), +GFP_KERNEL ); +if (!ctx->supplies) +return -ENOMEM ; + +for (i =0 ; i < desc->num_supplies; i++) + ctx->supplies[i].supply = desc->supply_names[i]; + + ret =devm_regulator_bulk_get (&dsi->dev, desc->num_supplies, + ctx->supplies); +if (ret <0 ) +return ret; + + ctx->reset_gpio =devm_gpiod_get (dev,"reset" ,GPIOD_OUT_LOW ); +if (IS_ERR (ctx->reset_gpio)) { +DRM_DEV_ERROR (dev,"Can't get reset gpio\n" ); +return PTR_ERR (ctx->reset_gpio); + } + +mipi_dsi_set_drvdata (dsi, ctx); + +drm_panel_init (&ctx->panel, &dsi->dev, &st7703_drm_funcs, +DRM_MODE_CONNECTOR_DSI ); + + ret =drm_panel_of_backlight (&ctx->panel); +if (ret) +return ret; + +drm_panel_add (&ctx->panel); + + ret =mipi_dsi_attach (dsi); +if (ret <0 ) { +drm_panel_remove (&ctx->panel); +return ret; + } + +return 0 ; +} + +static void st7703_shutdown (struct mipi_dsi_device *dsi) +{ +struct st7703 *ctx =mipi_dsi_get_drvdata (dsi); +int ret; + + ret =drm_panel_unprepare (&ctx->panel); +if (ret <0 ) +DRM_DEV_ERROR (&dsi->dev, +"Failed to unprepare panel (%d)\n" , ret); +} + +static int st7703_remove (struct mipi_dsi_device *dsi) +{ +struct st7703 *ctx =mipi_dsi_get_drvdata (dsi); +int ret; + +st7703_shutdown (dsi); + + ret =mipi_dsi_detach (dsi); +if (ret <0 ) +DRM_DEV_ERROR (&dsi->dev, +"Failed to detach from DSI host (%d)\n" , ret); + +drm_panel_remove (&ctx->panel); + +return 0 ; +} + +static const struct of_device_id st7703_of_match[] = { + { .compatible ="xingbangda,xbd599" , .data = &xbd599_desc }, + {/* sentinel */ } +}; +MODULE_DEVICE_TABLE (of, st7703_of_match); + +static struct mipi_dsi_driver st7703_driver = { + .probe = st7703_probe, + .remove = st7703_remove, + .shutdown = st7703_shutdown, + .driver = { + .name ="st7703" , + .of_match_table = st7703_of_match, + }, +}; +module_mipi_dsi_driver (st7703_driver); + +MODULE_AUTHOR ("Icenowy Zheng <[email protected]>" ); +MODULE_DESCRIPTION ("DRM driver for Sitronix ST7703 MIPI DSI panel" ); +MODULE_LICENSE ("GPL v2" );Signature · 1 line
2.27.0
Quoted 8 lines
Quoted 4 lines
Quoted 4 lines
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v4 3/5] drm: panel: Add Xingbangda XBD599 panel (ST7703 controller)
Hello Sam,
Quoted 3 lines · Sam Ravnborg
Quoted 2 lines · Ondřej Jirman
Quoted 1 line · Sam Ravnborg
Hi Ondrej et al.
...
Quoted 10 lines
Quoted 7 lines
Quoted 5 lines
Would it not be better to have one st7703 driver that suipports both panels?
The driver would need dedicated init functions depending on the panel. But a lot could also be shared.
I guess I can move the code there.
In the same process the river should then be renamed to follow other sitronix based drivers.
So the next developer will recognize this and use the correct driver.
Are driver/module names considered kernel ABI? Or is it possible to change them?
regards,
o.
Re: [PATCH v4 3/5] drm: panel: Add Xingbangda XBD599 panel (ST7703 controller)
Hi!
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 5 lines
Would it not be better to have one st7703 driver that suipports both panels?
The driver would need dedicated init functions depending on the panel. But a lot could also be shared.
Quoted 7 lines
Quoted 4 lines
Quoted 1 line
I guess I can move the code there.
In the same process the river should then be renamed to follow other sitronix based drivers.
So the next developer will recognize this and use the correct driver.Are driver/module names considered kernel ABI? Or is it possible to change them?
I believe you can get away with changing them.
Pavel
Signature · 6 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
PATCH v4 4/5 arm64: dts: sun50i-a64-pinephone: Enable LCD support on PinePhone
In reply to Ondrej JirmanFrom: Icenowy Zheng <[email protected]>
PinePhone uses PWM backlight and a XBD599 LCD panel over DSI for display.
Backlight levels curve was optimized by Martijn Braam using a lux meter.
Add its device nodes.
--- .../allwinner/sun50i-a64-pinephone-1.1.dts | 19 ++++++++++ .../dts/allwinner/sun50i-a64-pinephone.dtsi | 35 +++++++++++++++++++ 2 files changed, 54 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts +19 -0
@@ -9,3 +9,22 @@ / { model = "Pine64 PinePhone Braveheart (1.1)"; compatible = "pine64,pinephone-1.1", "allwinner,sun50i-a64"; }; + +&backlight { + power-supply = <®_ldo_io0>; + /* + * PWM backlight circuit on this PinePhone revision was changed since + * 1.0, and the lowest PWM duty cycle that doesn't lead to backlight + * being off is around 20%. Duty cycle for the lowest brightness level + * also varries quite a bit between individual boards, so the lowest + * value here was chosen as a safe default. + */ + brightness-levels = < + 774 793 814 842 + 882 935 1003 1088 + 1192 1316 1462 1633 + 1830 2054 2309 2596 + 2916 3271 3664 4096>; + num-interpolated-steps = <50>; + default-brightness-level = <400>; +};
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi +35 -0
@@ -16,6 +16,13 @@ aliases { serial0 = &uart0; }; + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&r_pwm 0 50000 PWM_POLARITY_INVERTED>; + enable-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */ + /* Backlight configuration differs per PinePhone revision. */ + }; + chosen { stdout-path = "serial0:115200n8"; };
@@ -84,6 +91,30 @@ &dai { status = "okay"; }; +&de { + status = "okay"; +}; + +&dphy { + status = "okay"; +}; + +&dsi { + vcc-dsi-supply = <®_dldo1>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + panel@0 { + compatible = "xingbangda,xbd599", "sitronix,st7703"; + reg = <0>; + reset-gpios = <&pio 3 23 GPIO_ACTIVE_LOW>; /* PD23 */ + iovcc-supply = <®_dldo2>; + vcc-supply = <®_ldo_io0>; + backlight = <&backlight>; + }; +}; + &ehci0 { status = "okay"; };
@@ -188,6 +219,10 @@ &r_pio { */ }; +&r_pwm { + status = "okay"; +}; + &r_rsb { status = "okay";
Signature · 7 lines
2.27.0 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v4 5/5 arm64: dts: sun50i-a64-pinephone: Add touchscreen support
In reply to Ondrej JirmanPinephone has a Goodix GT917S capacitive touchscreen controller on I2C0 bus. Add support for it.
--- .../dts/allwinner/sun50i-a64-pinephone.dtsi | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi +19 -0
@@ -123,6 +123,25 @@ &ehci1 { status = "okay"; }; +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + status = "okay"; + + touchscreen@5d { + compatible = "goodix,gt917s", "goodix,gt911"; + reg = <0x5d>; + interrupt-parent = <&pio>; + interrupts = <7 4 IRQ_TYPE_LEVEL_HIGH>; /* PH4 */ + irq-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + reset-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */ + AVDD28-supply = <®_ldo_io0>; + VDDIO-supply = <®_ldo_io0>; + touchscreen-size-x = <720>; + touchscreen-size-y = <1440>; + }; +}; + &i2c1 { status = "okay";
Signature · 1 line
2.27.0