Skip to contentSkip to conversation

net: phy: call phy_disable_interrupts() in phy_init_hw()

PATCH Superseded Jisheng Zhang 2 participants 4 messages Jun 23, 2020

Subsystems (3)

v2 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

v2 cover net: phy: call phy_disable_interrupts() in phy_init_hw()

We face an issue with rtl8211f, a pin is shared between INTB and PMEB, and the PHY Register Accessible Interrupt is enabled by default, so the INTB/PMEB pin is always active in polling mode case.

As Heiner pointed out "I was thinking about calling phy_disable_interrupts() in phy_init_hw(), to have a defined init state as we don't know in which state the PHY is if the PHY driver is loaded. We shouldn't assume that it's the chip power-on defaults, BIOS or boot loader could have changed this. Or in case of dual-boot systems the other OS could leave the PHY in whatever state."

patch1 exports phy_disable_interrupts() so that it could be used in phy_init_hw() to have a defined init state.

patch2 calls phy_disable_interrupts() in phy_init_hw() to have a defined init state.

Since v1:
- EXPORT the correct symbol

Jisheng Zhang (2):
net: phy: export phy_disable_interrupts()
net: phy: call phy_disable_interrupts() in phy_init_hw()

 drivers/net/phy/phy.c        | 3 ++-
 drivers/net/phy/phy_device.c | 7 +++++--
 include/linux/phy.h          | 1 +
 3 files changed, 8 insertions(+), 3 deletions(-)
Signature · 1 line
2.27.0
#1 lore raw

PATCH v2 1/2 net: phy: export phy_disable_interrupts()

We face an issue with rtl8211f, a pin is shared between INTB and PMEB, and the PHY Register Accessible Interrupt is enabled by default, so the INTB/PMEB pin is always active in polling mode case.

As Heiner pointed out "I was thinking about calling phy_disable_interrupts() in phy_init_hw(), to have a defined init state as we don't know in which state the PHY is if the PHY driver is loaded. We shouldn't assume that it's the chip power-on defaults, BIOS or boot loader could have changed this. Or in case of dual-boot systems the other OS could leave the PHY in whatever state."

Export phy_disable_interrupts() so that it could be used in phy_init_hw() to have a defined init state.

---
 drivers/net/phy/phy.c | 3 ++-
 include/linux/phy.h   | 1 +
 2 files changed, 3 insertions(+), 1 deletion(-)
drivers/net/phy/phy.c +2 -1
index 1de3938628f4..cd2dbbdba235 100644
@@ -840,7 +840,7 @@ static void phy_error(struct phy_device *phydev)
  * phy_disable_interrupts - Disable the PHY interrupts from the PHY side
  * @phydev: target phy_device struct
  */
-static int phy_disable_interrupts(struct phy_device *phydev)
+int phy_disable_interrupts(struct phy_device *phydev)
 {
 	int err;
 
@@ -852,6 +852,7 @@ static int phy_disable_interrupts(struct phy_device *phydev)
 	/* Clear the interrupt */
 	return phy_clear_interrupt(phydev);
 }
+EXPORT_SYMBOL_GPL(phy_disable_interrupts);
 
 /**
  * phy_interrupt - PHY interrupt handler
include/linux/phy.h +1 -0
index 8c05d0fb5c00..b693b609b2f5 100644
@@ -1416,6 +1416,7 @@ int phy_ethtool_ksettings_set(struct phy_device *phydev,
 int phy_mii_ioctl(struct phy_device *phydev, struct ifreq *ifr, int cmd);
 int phy_do_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd);
 int phy_do_ioctl_running(struct net_device *dev, struct ifreq *ifr, int cmd);
+int phy_disable_interrupts(struct phy_device *phydev);
 void phy_request_interrupt(struct phy_device *phydev);
 void phy_free_interrupt(struct phy_device *phydev);
 void phy_print_status(struct phy_device *phydev);
Signature · 1 line
2.27.0
maintainer
#2 lore raw

Re: [PATCH v2 1/2] net: phy: export phy_disable_interrupts()

From: Jisheng Zhang <[email protected]>
Date: Tue, 23 Jun 2020 15:41:04 +0800

Quoted 1 line

+EXPORT_SYMBOL_GPL(phy_disable_interrupts);

phy.o and phy_device.o are always linked together, therefore you don't need a module symbol export.

If you plan to use it later in a device, submit the symbol export with the driver change that uses it.

#3 lore raw

PATCH v2 2/2 net: phy: call phy_disable_interrupts() in phy_init_hw()

In reply to Jisheng Zhang

Call phy_disable_interrupts() in phy_init_hw() to "have a defined init state as we don't know in which state the PHY is if the PHY driver is loaded. We shouldn't assume that it's the chip power-on defaults, BIOS or boot loader could have changed this. Or in case of dual-boot systems the other OS could leave the PHY in whatever state." as pointed out by Heiner.

---
 drivers/net/phy/phy_device.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/net/phy/phy_device.c +5 -2
index 04946de74fa0..f17d397ba689 100644
@@ -1090,10 +1090,13 @@ int phy_init_hw(struct phy_device *phydev)
 	if (ret < 0)
 		return ret;
 
-	if (phydev->drv->config_init)
+	if (phydev->drv->config_init) {
 		ret = phydev->drv->config_init(phydev);
+		if (ret < 0)
+			return ret;
+	}
 
-	return ret;
+	return phy_disable_interrupts(phydev);
 }
 EXPORT_SYMBOL(phy_init_hw);
 
Signature · 1 line
2.27.0