Skip to contentSkip to conversation

arm64: ti: k3-j721e: Add SERDES PHY and USB3.0 support

PATCH Applied Roger Quadros 3 participants 10 messages Jun 29, 2020 – Jul 17, 2020

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

v4 cover arm64: ti: k3-j721e: Add SERDES PHY and USB3.0 support

Hi Tero,

This series adds SERDES PHY support and Type-C USB Super-Speed support to the J721E EVM.

Please queue this for -next. Thanks.

cheers,
-roger

Changelog:
v4:
- Removed redundant patch
- used compaible string for yaml filename
- typo fix s/mdf/mfd in patch subject
- added simple-mfd, address-cells, size-cells and ranges

v3:
- Add new DT schema for J721E System controller.
- Re-order system controller's compatible string i.e. most compatible to least.

v2:
- Addressed Rob's comments.
- Changed type-C debounce delay from 300ms to 700ms as 300ms is not sufficient on EVM.

Kishon Vijay Abraham I (2):
arm64: dts: ti: k3-j721e-main: Add WIZ and SERDES PHY nodes
arm64: dts: ti: k3-j721e-main: Add system controller node and SERDES
lane mux

Roger Quadros (4):
dt-bindings: mfd: ti,j721e-system-controller.yaml: Add J721e system
controller
arm64: dts: ti: k3-j721e-main.dtsi: Add USB to SERDES MUX
arm64: dts: ti: k3-j721e: Enable Super-Speed support for USB0
arm64: dts: k3-j721e-proc-board: Add wait time for sampling Type-C DIR
line

 .../mfd/ti,j721e-system-controller.yaml       |  74 +++++
 .../dts/ti/k3-j721e-common-proc-board.dts     |  33 ++-
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi     | 275 ++++++++++++++++++
 include/dt-bindings/mux/mux-j721e-wiz.h       |  53 ++++
 4 files changed, 433 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mfd/ti,j721e-system-controller.yaml
 create mode 100644 include/dt-bindings/mux/mux-j721e-wiz.h
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
#1 lore raw

PATCH v4 1/6 dt-bindings: mfd: ti,j721e-system-controller.yaml: Add J721e system controller

Add DT binding schema for J721e system controller.

---
 .../mfd/ti,j721e-system-controller.yaml       | 74 +++++++++++++++++++
 1 file changed, 74 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/ti,j721e-system-controller.yaml
Documentation/devicetree/bindings/mfd/ti,j721e-system-controller.yaml new file +74 -0
new file mode 100644
index 000000000000..03d0a232c75e
@@ -0,0 +1,74 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) 2020 Texas Instruments Incorporated - http://www.ti.com/
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/ti,j721e-system-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI J721e System Controller Registers R/W Device Tree Bindings
+
+description: |
+  This represents the Control Module registers (CTRL_MMR0) on the SoC.
+  System controller node represents a register region containing a set
+  of miscellaneous registers. The registers are not cohesive enough to
+  represent as any specific type of device. The typical use-case is
+  for some other node's driver, or platform-specific code, to acquire
+  a reference to the syscon node (e.g. by phandle, node path, or
+  search using a specific compatible value), interrogate the node (or
+  associated OS driver) to determine the location of the registers,
+  and access the registers directly.
+
+maintainers:
+  - Kishon Vijay Abraham I <[email protected]>
+  - Roger Quadros <[email protected]
+
+properties:
+  compatible:
+    anyOf:
+      - items:
+        - enum:
+           - ti,j721e-system-controller
+        - const: syscon
+        - const: simple-mfd
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 1
+
+  ranges: true
+
+# Optional children
+
+  "^serdes-ln-ctrl@[0-9a-f]+$":
+    type: object
+    description: |
+      This is the SERDES lane control mux. It should follow the bindings
+      specified in
+      Documentation/devicetree/bindings/mux/reg-mux.txt
+
+required:
+  - compatible
+  - reg
+  - "#address-cells"
+  - "#size-cells"
+  - ranges
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    scm_conf: scm-conf@100000 {
+        compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
+        reg = <0x00100000 0x1c000>;
+        #address-cells = <1>;
+        #size-cells = <1>;
+        ranges;
+
+        serdes_ln_ctrl: serdes-ln-ctrl@4080 {
+            compatible = "mmio-mux";
+            reg = <0x00004080 0x50>;
+        };
+    };
+...
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
maintainer Reviewed-by on v4 1/6
#2 lore raw

Re: [PATCH v4 1/6] dt-bindings: mfd: ti,j721e-system-controller.yaml: Add J721e system controller

Quoted 8 lines · Roger Quadros

Add DT binding schema for J721e system controller.

---
 .../mfd/ti,j721e-system-controller.yaml       | 74 +++++++++++++++++++
 1 file changed, 74 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/ti,j721e-system-controller.yaml
#3 lore raw

PATCH v4 2/6 arm64: dts: ti: k3-j721e-main: Add WIZ and SERDES PHY nodes

In reply to Roger Quadros

From: Kishon Vijay Abraham I <[email protected]>

Add DT nodes for all instances of WIZ and SERDES modules.

---
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 241 ++++++++++++++++++++++
 1 file changed, 241 insertions(+)
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +241 -0
index 96c929da639d..b11cb51af747 100644
@@ -4,6 +4,7 @@
  *
  * Copyright (C) 2016-2019 Texas Instruments Incorporated - http://www.ti.com/
  */
+#include <dt-bindings/phy/phy.h>
 
 &cbass_main {
 	msmc_ram: sram@70000000 {
@@ -277,6 +278,246 @@
 		pinctrl-single,function-mask = <0xffffffff>;
 	};
 
+	dummy_cmn_refclk: dummy-cmn-refclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <100000000>;
+	};
+
+	dummy_cmn_refclk1: dummy-cmn-refclk1 {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <100000000>;
+	};
+
+	serdes_wiz0: wiz@5000000 {
+		compatible = "ti,j721e-wiz-16g";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		power-domains = <&k3_pds 292 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 292 5>, <&k3_clks 292 11>, <&dummy_cmn_refclk>;
+		clock-names = "fck", "core_ref_clk", "ext_ref_clk";
+		assigned-clocks = <&k3_clks 292 11>, <&k3_clks 292 0>;
+		assigned-clock-parents = <&k3_clks 292 15>, <&k3_clks 292 4>;
+		num-lanes = <2>;
+		#reset-cells = <1>;
+		ranges = <0x5000000 0x0 0x5000000 0x10000>;
+
+		wiz0_pll0_refclk: pll0-refclk {
+			clocks = <&k3_clks 292 11>, <&dummy_cmn_refclk>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz0_pll0_refclk>;
+			assigned-clock-parents = <&k3_clks 292 11>;
+		};
+
+		wiz0_pll1_refclk: pll1-refclk {
+			clocks = <&k3_clks 292 0>, <&dummy_cmn_refclk1>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz0_pll1_refclk>;
+			assigned-clock-parents = <&k3_clks 292 0>;
+		};
+
+		wiz0_refclk_dig: refclk-dig {
+			clocks = <&k3_clks 292 11>, <&k3_clks 292 0>, <&dummy_cmn_refclk>, <&dummy_cmn_refclk1>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz0_refclk_dig>;
+			assigned-clock-parents = <&k3_clks 292 11>;
+		};
+
+		wiz0_cmn_refclk_dig_div: cmn-refclk-dig-div {
+			clocks = <&wiz0_refclk_dig>;
+			#clock-cells = <0>;
+		};
+
+		wiz0_cmn_refclk1_dig_div: cmn-refclk1-dig-div {
+			clocks = <&wiz0_pll1_refclk>;
+			#clock-cells = <0>;
+		};
+
+		serdes0: serdes@5000000 {
+			compatible = "ti,sierra-phy-t0";
+			reg-names = "serdes";
+			reg = <0x5000000 0x10000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			resets = <&serdes_wiz0 0>;
+			reset-names = "sierra_reset";
+			clocks = <&wiz0_cmn_refclk_dig_div>, <&wiz0_cmn_refclk1_dig_div>;
+			clock-names = "cmn_refclk_dig_div", "cmn_refclk1_dig_div";
+		};
+	};
+
+	serdes_wiz1: wiz@5010000 {
+		compatible = "ti,j721e-wiz-16g";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		power-domains = <&k3_pds 293 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 293 5>, <&k3_clks 293 13>, <&dummy_cmn_refclk>;
+		clock-names = "fck", "core_ref_clk", "ext_ref_clk";
+		assigned-clocks = <&k3_clks 293 13>, <&k3_clks 293 0>;
+		assigned-clock-parents = <&k3_clks 293 17>, <&k3_clks 293 4>;
+		num-lanes = <2>;
+		#reset-cells = <1>;
+		ranges = <0x5010000 0x0 0x5010000 0x10000>;
+
+		wiz1_pll0_refclk: pll0-refclk {
+			clocks = <&k3_clks 293 13>, <&dummy_cmn_refclk>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz1_pll0_refclk>;
+			assigned-clock-parents = <&k3_clks 293 13>;
+		};
+
+		wiz1_pll1_refclk: pll1-refclk {
+			clocks = <&k3_clks 293 0>, <&dummy_cmn_refclk1>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz1_pll1_refclk>;
+			assigned-clock-parents = <&k3_clks 293 0>;
+		};
+
+		wiz1_refclk_dig: refclk-dig {
+			clocks = <&k3_clks 293 13>, <&k3_clks 293 0>, <&dummy_cmn_refclk>, <&dummy_cmn_refclk1>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz1_refclk_dig>;
+			assigned-clock-parents = <&k3_clks 293 13>;
+		};
+
+		wiz1_cmn_refclk_dig_div: cmn-refclk-dig-div{
+			clocks = <&wiz1_refclk_dig>;
+			#clock-cells = <0>;
+		};
+
+		wiz1_cmn_refclk1_dig_div: cmn-refclk1-dig-div {
+			clocks = <&wiz1_pll1_refclk>;
+			#clock-cells = <0>;
+		};
+
+		serdes1: serdes@5010000 {
+			compatible = "ti,sierra-phy-t0";
+			reg-names = "serdes";
+			reg = <0x5010000 0x10000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			resets = <&serdes_wiz1 0>;
+			reset-names = "sierra_reset";
+			clocks = <&wiz1_cmn_refclk_dig_div>, <&wiz1_cmn_refclk1_dig_div>;
+			clock-names = "cmn_refclk_dig_div", "cmn_refclk1_dig_div";
+		};
+	};
+
+	serdes_wiz2: wiz@5020000 {
+		compatible = "ti,j721e-wiz-16g";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		power-domains = <&k3_pds 294 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 294 5>, <&k3_clks 294 11>, <&dummy_cmn_refclk>;
+		clock-names = "fck", "core_ref_clk", "ext_ref_clk";
+		assigned-clocks = <&k3_clks 294 11>, <&k3_clks 294 0>;
+		assigned-clock-parents = <&k3_clks 294 15>, <&k3_clks 294 4>;
+		num-lanes = <2>;
+		#reset-cells = <1>;
+		ranges = <0x5020000 0x0 0x5020000 0x10000>;
+
+		wiz2_pll0_refclk: pll0-refclk {
+			clocks = <&k3_clks 294 11>, <&dummy_cmn_refclk>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz2_pll0_refclk>;
+			assigned-clock-parents = <&k3_clks 294 11>;
+		};
+
+		wiz2_pll1_refclk: pll1-refclk {
+			clocks = <&k3_clks 294 0>, <&dummy_cmn_refclk1>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz2_pll1_refclk>;
+			assigned-clock-parents = <&k3_clks 294 0>;
+		};
+
+		wiz2_refclk_dig: refclk-dig {
+			clocks = <&k3_clks 294 11>, <&k3_clks 294 0>, <&dummy_cmn_refclk>, <&dummy_cmn_refclk1>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz2_refclk_dig>;
+			assigned-clock-parents = <&k3_clks 294 11>;
+		};
+
+		wiz2_cmn_refclk_dig_div: cmn-refclk-dig-div {
+			clocks = <&wiz2_refclk_dig>;
+			#clock-cells = <0>;
+		};
+
+		wiz2_cmn_refclk1_dig_div: cmn-refclk1-dig-div {
+			clocks = <&wiz2_pll1_refclk>;
+			#clock-cells = <0>;
+		};
+
+		serdes2: serdes@5020000 {
+			compatible = "ti,sierra-phy-t0";
+			reg-names = "serdes";
+			reg = <0x5020000 0x10000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			resets = <&serdes_wiz2 0>;
+			reset-names = "sierra_reset";
+			clocks = <&wiz2_cmn_refclk_dig_div>, <&wiz2_cmn_refclk1_dig_div>;
+			clock-names = "cmn_refclk_dig_div", "cmn_refclk1_dig_div";
+		};
+	};
+
+	serdes_wiz3: wiz@5030000 {
+		compatible = "ti,j721e-wiz-16g";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		power-domains = <&k3_pds 295 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 295 5>, <&k3_clks 295 9>, <&dummy_cmn_refclk>;
+		clock-names = "fck", "core_ref_clk", "ext_ref_clk";
+		assigned-clocks = <&k3_clks 295 9>, <&k3_clks 295 0>;
+		assigned-clock-parents = <&k3_clks 295 13>, <&k3_clks 295 4>;
+		num-lanes = <2>;
+		#reset-cells = <1>;
+		ranges = <0x5030000 0x0 0x5030000 0x10000>;
+
+		wiz3_pll0_refclk: pll0-refclk {
+			clocks = <&k3_clks 295 9>, <&dummy_cmn_refclk>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz3_pll0_refclk>;
+			assigned-clock-parents = <&k3_clks 295 9>;
+		};
+
+		wiz3_pll1_refclk: pll1-refclk {
+			clocks = <&k3_clks 295 0>, <&dummy_cmn_refclk1>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz3_pll1_refclk>;
+			assigned-clock-parents = <&k3_clks 295 0>;
+		};
+
+		wiz3_refclk_dig: refclk-dig {
+			clocks = <&k3_clks 295 9>, <&k3_clks 295 0>, <&dummy_cmn_refclk>, <&dummy_cmn_refclk1>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz3_refclk_dig>;
+			assigned-clock-parents = <&k3_clks 295 9>;
+		};
+
+		wiz3_cmn_refclk_dig_div: cmn-refclk-dig-div {
+			clocks = <&wiz3_refclk_dig>;
+			#clock-cells = <0>;
+		};
+
+		wiz3_cmn_refclk1_dig_div: cmn-refclk1-dig-div {
+			clocks = <&wiz3_pll1_refclk>;
+			#clock-cells = <0>;
+		};
+
+		serdes3: serdes@5030000 {
+			compatible = "ti,sierra-phy-t0";
+			reg-names = "serdes";
+			reg = <0x5030000 0x10000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			resets = <&serdes_wiz3 0>;
+			reset-names = "sierra_reset";
+			clocks = <&wiz3_cmn_refclk_dig_div>, <&wiz3_cmn_refclk1_dig_div>;
+			clock-names = "cmn_refclk_dig_div", "cmn_refclk1_dig_div";
+		};
+	};
+
 	main_uart0: serial@2800000 {
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02800000 0x00 0x100>;
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
#4 lore raw

PATCH v4 3/6 arm64: dts: ti: k3-j721e-main: Add system controller node and SERDES lane mux

In reply to Roger Quadros

From: Kishon Vijay Abraham I <[email protected]>

The system controller node manages the CTRL_MMR0 region.
Add serdes_ln_ctrl node which is used for controlling the SERDES lane mux.

---
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 27 ++++++++++++
 include/dt-bindings/mux/mux-j721e-wiz.h   | 53 +++++++++++++++++++++++
 2 files changed, 80 insertions(+)
 create mode 100644 include/dt-bindings/mux/mux-j721e-wiz.h
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +27 -0
index b11cb51af747..5f1f11b6fdff 100644
@@ -5,6 +5,8 @@
  * Copyright (C) 2016-2019 Texas Instruments Incorporated - http://www.ti.com/
  */
 #include <dt-bindings/phy/phy.h>
+#include <dt-bindings/mux/mux.h>
+#include <dt-bindings/mux/mux-j721e-wiz.h>
 
 &cbass_main {
 	msmc_ram: sram@70000000 {
@@ -19,6 +21,31 @@
 		};
 	};
 
+	scm_conf: scm-conf@100000 {
+		compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
+		reg = <0 0x00100000 0 0x1c000>; /* excludes pinctrl region */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x00100000 0x1c000>;
+
+		serdes_ln_ctrl: serdes-ln-ctrl@4080 {
+			compatible = "mmio-mux";
+			reg = <0x00004080 0x50>;
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x4080 0x3>, <0x4084 0x3>, /* SERDES0 lane0/1 select */
+					<0x4090 0x3>, <0x4094 0x3>, /* SERDES1 lane0/1 select */
+					<0x40a0 0x3>, <0x40a4 0x3>, /* SERDES2 lane0/1 select */
+					<0x40b0 0x3>, <0x40b4 0x3>, /* SERDES3 lane0/1 select */
+					<0x40c0 0x3>, <0x40c4 0x3>, <0x40c8 0x3>, <0x40cc 0x3>;
+					/* SERDES4 lane0/1/2/3 select */
+			idle-states = <SERDES0_LANE0_PCIE0_LANE0>, <SERDES0_LANE1_PCIE0_LANE1>,
+				      <SERDES1_LANE0_PCIE1_LANE0>, <SERDES1_LANE1_PCIE1_LANE1>,
+				      <SERDES2_LANE0_PCIE2_LANE0>, <SERDES2_LANE1_PCIE2_LANE1>,
+				      <MUX_IDLE_AS_IS>, <SERDES3_LANE1_USB3_0>,
+				      <SERDES4_LANE0_EDP_LANE0>, <SERDES4_LANE1_EDP_LANE1>, <SERDES4_LANE2_EDP_LANE2>, <SERDES4_LANE3_EDP_LANE3>;
+		};
+	};
+
 	gic500: interrupt-controller@1800000 {
 		compatible = "arm,gic-v3";
 		#address-cells = <2>;
include/dt-bindings/mux/mux-j721e-wiz.h new file +53 -0

53 lines not on this page · raw message

Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
maintainer Acked-by on v4 3/6
#5 lore raw

Re: [PATCH v4 3/6] arm64: dts: ti: k3-j721e-main: Add system controller node and SERDES lane mux

Quoted 5 lines · Roger Quadros

From: Kishon Vijay Abraham I <[email protected]>

The system controller node manages the CTRL_MMR0 region.
Add serdes_ln_ctrl node which is used for controlling the SERDES lane mux.

Quoted 8 lines
---
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 27 ++++++++++++
 include/dt-bindings/mux/mux-j721e-wiz.h   | 53 +++++++++++++++++++++++
 2 files changed, 80 insertions(+)
 create mode 100644 include/dt-bindings/mux/mux-j721e-wiz.h
#6 lore raw

PATCH v4 4/6 arm64: dts: ti: k3-j721e-main.dtsi: Add USB to SERDES MUX

In reply to Roger Quadros

The USB controllers can be connected to one of the 2 SERDESes using a MUX. Add a MUX controller node fot that.

---
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +7 -0
index 5f1f11b6fdff..469620aec9d4 100644
@@ -44,6 +44,13 @@
 				      <MUX_IDLE_AS_IS>, <SERDES3_LANE1_USB3_0>,
 				      <SERDES4_LANE0_EDP_LANE0>, <SERDES4_LANE1_EDP_LANE1>, <SERDES4_LANE2_EDP_LANE2>, <SERDES4_LANE3_EDP_LANE3>;
 		};
+
+		usb_serdes_mux: mux-controller@4000 {
+			compatible = "mmio-mux";
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x4000 0x8000000>, /* USB0 to SERDES0/3 mux */
+					<0x4010 0x8000000>; /* USB1 to SERDES1/2 mux */
+	    };
 	};
 
 	gic500: interrupt-controller@1800000 {
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
#7 lore raw

PATCH v4 5/6 arm64: dts: ti: k3-j721e: Enable Super-Speed support for USB0

In reply to Roger Quadros

USB0 supports super-speed mode on the EVM. Enable that. On the EVM, USB0 uses SERDES3 for super-speed lane.

Since USB0 is a type-C port, it needs to support lane swapping for cable flip support. This is provided using SERDES lane swap feature. Provide the Type-C cable orientation GPIO to the SERDES Wrapper driver.

---
 .../dts/ti/k3-j721e-common-proc-board.dts     | 32 +++++++++++++++++--
 1 file changed, 30 insertions(+), 2 deletions(-)
arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts +30 -2
index 6df823aaa37c..3294b96ebba8 100644
@@ -60,6 +60,7 @@
 	main_usbss0_pins_default: main_usbss0_pins_default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */
+			J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */
 		>;
 	};
 
@@ -335,16 +336,43 @@
 	status = "disabled";
 };
 
+&usb_serdes_mux {
+	idle-states = <1>, <0>; /* USB0 to SERDES3, USB1 to SERDES1 */
+};
+
+&serdes_ln_ctrl {
+	idle-states = <SERDES0_LANE0_PCIE0_LANE0>, <SERDES0_LANE1_PCIE0_LANE1>,
+		      <SERDES1_LANE0_PCIE1_LANE0>, <SERDES1_LANE1_PCIE1_LANE1>,
+		      <SERDES2_LANE0_PCIE2_LANE0>, <SERDES2_LANE1_PCIE2_LANE1>,
+		      <SERDES3_LANE0_USB3_0_SWAP>, <SERDES3_LANE1_USB3_0>,
+		      <SERDES4_LANE0_EDP_LANE0>, <SERDES4_LANE1_EDP_LANE1>, <SERDES4_LANE2_EDP_LANE2>, <SERDES4_LANE3_EDP_LANE3>;
+};
+
+&serdes_wiz3 {
+	typec-dir-gpios = <&main_gpio1 3 GPIO_ACTIVE_HIGH>;
+};
+
+&serdes3 {
+	serdes3_usb_link: link@0 {
+		reg = <0>;
+		cdns,num-lanes = <2>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_USB3>;
+		resets = <&serdes_wiz3 1>, <&serdes_wiz3 2>;
+	};
+};
+
 &usbss0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_usbss0_pins_default>;
-	ti,usb2-only;
 	ti,vbus-divider;
 };
 
 &usb0 {
 	dr_mode = "otg";
-	maximum-speed = "high-speed";
+	maximum-speed = "super-speed";
+	phys = <&serdes3_usb_link>;
+	phy-names = "cdns3,usb3-phy";
 };
 
 &usbss1 {
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
#8 lore raw

PATCH v4 6/6 arm64: dts: k3-j721e-proc-board: Add wait time for sampling Type-C DIR line

In reply to Roger Quadros

The Type-C compainon chip on the board needs ~133ms (tCCB_DEFAULT) to debounce the CC lines in order to detect attach and plug orientation and reflect the correct DIR status. [1]

On the EVM however we need to wait upto 700ms before sampling the Type-C DIR line else we can get incorrect direction state.

[1] http://www.ti.com/lit/ds/symlink/tusb321.pdf

---
 arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts +1 -0
index 3294b96ebba8..6307fe5ccb06 100644
@@ -350,6 +350,7 @@
 
 &serdes_wiz3 {
 	typec-dir-gpios = <&main_gpio1 3 GPIO_ACTIVE_HIGH>;
+	typec-dir-debounce-ms = <700>;	/* TUSB321, tCCB_DEFAULT 133 ms */
 };
 
 &serdes3 {
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
Applied
#9 lore raw
In reply to Roger Quadros
Quoted 6 lines · Roger Quadros

Hi Tero,

This series adds SERDES PHY support and Type-C USB Super-Speed support to the J721E EVM.

Please queue this for -next. Thanks.

Queued up for 5.9, thanks.

-Tero

Quoted 34 lines

cheers,
-roger

Changelog:
v4:
- Removed redundant patch
- used compaible string for yaml filename
- typo fix s/mdf/mfd in patch subject
- added simple-mfd, address-cells, size-cells and ranges

v3:
- Add new DT schema for J721E System controller.
- Re-order system controller's compatible string i.e. most compatible to least.

v2:
- Addressed Rob's comments.
- Changed type-C debounce delay from 300ms to 700ms as 300ms is not sufficient on EVM.

Kishon Vijay Abraham I (2):
arm64: dts: ti: k3-j721e-main: Add WIZ and SERDES PHY nodes
arm64: dts: ti: k3-j721e-main: Add system controller node and SERDES
lane mux

Roger Quadros (4):
dt-bindings: mfd: ti,j721e-system-controller.yaml: Add J721e system
controller
arm64: dts: ti: k3-j721e-main.dtsi: Add USB to SERDES MUX
arm64: dts: ti: k3-j721e: Enable Super-Speed support for USB0
arm64: dts: k3-j721e-proc-board: Add wait time for sampling Type-C DIR
line

Quoted 8 lines
  .../mfd/ti,j721e-system-controller.yaml       |  74 +++++
  .../dts/ti/k3-j721e-common-proc-board.dts     |  33 ++-
  arch/arm64/boot/dts/ti/k3-j721e-main.dtsi     | 275 ++++++++++++++++++
  include/dt-bindings/mux/mux-j721e-wiz.h       |  53 ++++
  4 files changed, 433 insertions(+), 2 deletions(-)

create mode 100644 Documentation/devicetree/bindings/mfd/ti,j721e-system-controller.yaml create mode 100644 include/dt-bindings/mux/mux-j721e-wiz.h

--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki