Skip to contentSkip to conversation

drm/ast: Managed modesetting

PATCH In review Thomas Zimmermann 2 participants 20 messages Jul 2, 2020 – Jul 3, 2020

Subsystems (3)
lore
Share & tools
lore

Thomas Zimmermann

author maintainer
#0 lore raw

v2 cover drm/ast: Managed modesetting

This is the first patchset to convert ast to use managed interfaces. These patches address modesetting. I expect that there will be at least one more set of patches for memory management and one for device structures.

Patches 1 to 11 tackle HW cursor handling. The overall point is to get cursor support out of the plane functions and put the code into helpers. There are quite a few improvements that make cursors easier and faster to use. Patch 10 converts cursors to managed release.

With cursors out of the way, modesetting initialization is much more simple. Patches 12 to 14 put all related code next to each other and switch to managed initialization.

The patchset was tested on AST2100 hardware.

v2:
* use to_ast_private() instead of
struct drm_device.dev_private (Sam)

Thomas Zimmermann (14):
drm/ast: Move cursor functions to ast_cursor.c drm/ast: Pass struct ast_private instance to cursor init/fini
functions
drm/ast: Move cursor fb pinning and mapping into helper drm/ast: Update cursor image and checksum from same function drm/ast: Move cursor pageflip into helper
drm/ast: Replace ast_cursor_move() with ast_cursor_show() drm/ast: Don't enable HW cursors twice during atomic update drm/ast: Add helper to hide cursor
drm/ast: Keep cursor HW BOs mapped
drm/ast: Managed cursor release
drm/ast: Init cursors before creating modesetting structures drm/ast: Replace struct ast_crtc with struct drm_crtc drm/ast: Use managed mode-config init
drm/ast: Initialize mode setting in ast_mode_config_init()

 drivers/gpu/drm/ast/Makefile     |   3 +-
 drivers/gpu/drm/ast/ast_cursor.c | 289 +++++++++++++++++++++++++++
 drivers/gpu/drm/ast/ast_drv.h    |  19 +-
 drivers/gpu/drm/ast/ast_main.c   |  35 +---
 drivers/gpu/drm/ast/ast_mode.c   | 322 ++++++-------------------------
 5 files changed, 359 insertions(+), 309 deletions(-)
 create mode 100644 drivers/gpu/drm/ast/ast_cursor.c

--
2.27.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

author maintainer
#1 lore raw

PATCH v2 1/14 drm/ast: Move cursor functions to ast_cursor.c

The cursor manipulation functions are unrelated to modesetting. Move them into their own file.

---
 drivers/gpu/drm/ast/Makefile     |   3 +-
 drivers/gpu/drm/ast/ast_cursor.c | 218 +++++++++++++++++++++++++++++++
 drivers/gpu/drm/ast/ast_drv.h    |   9 ++
 drivers/gpu/drm/ast/ast_mode.c   | 195 ---------------------------
 4 files changed, 229 insertions(+), 196 deletions(-)
 create mode 100644 drivers/gpu/drm/ast/ast_cursor.c
drivers/gpu/drm/ast/Makefile +2 -1
index 561f7c4199e4..6a5b3b247316 100644
@@ -3,6 +3,7 @@
 # Makefile for the drm device driver.  This driver provides support for the
 # Direct Rendering Infrastructure (DRI) in XFree86 4.1.0 and higher.
 
-ast-y := ast_drv.o ast_main.o ast_mode.o ast_ttm.o ast_post.o ast_dp501.o
+ast-y := ast_cursor.o ast_drv.o ast_main.o ast_mode.o ast_ttm.o ast_post.o \
+	 ast_dp501.o
 
 obj-$(CONFIG_DRM_AST) := ast.o
drivers/gpu/drm/ast/ast_cursor.c new file +218 -0

218 lines not on this page · raw message

drivers/gpu/drm/ast/ast_drv.h +9 -0
index c44c1376c697..245ed2e2d775 100644
@@ -314,4 +314,13 @@ bool ast_dp501_read_edid(struct drm_device *dev, u8 *ediddata);
 u8 ast_get_dp501_max_clk(struct drm_device *dev);
 void ast_init_3rdtx(struct drm_device *dev);
 void ast_release_firmware(struct drm_device *dev);
+
+/* ast_cursor.c */
+int ast_cursor_init(struct drm_device *dev);
+void ast_cursor_fini(struct drm_device *dev);
+int ast_cursor_update(void *dst, void *src, unsigned int width,
+		      unsigned int height);
+void ast_cursor_set_base(struct ast_private *ast, u64 address);
+int ast_cursor_move(struct drm_crtc *crtc, int x, int y);
+
 #endif
drivers/gpu/drm/ast/ast_mode.c +0 -195

210 lines not on this page · raw message

Signature · 6 lines
2.27.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#2 lore raw

PATCH v2 2/14 drm/ast: Pass struct ast_private instance to cursor init/fini functions

In reply to Thomas Zimmermann

Removes some typecasting.

v2:
* use to_ast_private() instead of struct drm_device.dev_private

---
 drivers/gpu/drm/ast/ast_cursor.c | 7 +++----
 drivers/gpu/drm/ast/ast_drv.h    | 4 ++--
 drivers/gpu/drm/ast/ast_mode.c   | 6 ++++--
 3 files changed, 9 insertions(+), 8 deletions(-)
drivers/gpu/drm/ast/ast_cursor.c +3 -4
index 53bb6eebc7cd..1d4f51a7fe22 100644
@@ -34,9 +34,9 @@
 /*
  * Allocate cursor BOs and pins them at the end of VRAM.
  */
-int ast_cursor_init(struct drm_device *dev)
+int ast_cursor_init(struct ast_private *ast)
 {
-	struct ast_private *ast = to_ast_private(dev);
+	struct drm_device *dev = ast->dev;
 	size_t size, i;
 	struct drm_gem_vram_object *gbo;
 	int ret;
@@ -72,9 +72,8 @@ int ast_cursor_init(struct drm_device *dev)
 	return ret;
 }
 
-void ast_cursor_fini(struct drm_device *dev)
+void ast_cursor_fini(struct ast_private *ast)
 {
-	struct ast_private *ast = to_ast_private(dev);
 	size_t i;
 	struct drm_gem_vram_object *gbo;
 
drivers/gpu/drm/ast/ast_drv.h +2 -2
index 245ed2e2d775..f7b120f862a8 100644
@@ -316,8 +316,8 @@ void ast_init_3rdtx(struct drm_device *dev);
 void ast_release_firmware(struct drm_device *dev);
 
 /* ast_cursor.c */
-int ast_cursor_init(struct drm_device *dev);
-void ast_cursor_fini(struct drm_device *dev);
+int ast_cursor_init(struct ast_private *ast);
+void ast_cursor_fini(struct ast_private *ast);
 int ast_cursor_update(void *dst, void *src, unsigned int width,
 		      unsigned int height);
 void ast_cursor_set_base(struct ast_private *ast, u64 address);
drivers/gpu/drm/ast/ast_mode.c +4 -2
index c8399699d773..e69965f5636d 100644
@@ -1149,7 +1149,7 @@ int ast_mode_init(struct drm_device *dev)
 	drm_plane_helper_add(&ast->cursor_plane,
 			     &ast_cursor_plane_helper_funcs);
 
-	ast_cursor_init(dev);
+	ast_cursor_init(ast);
 	ast_crtc_init(dev);
 	ast_encoder_init(dev);
 	ast_connector_init(dev);
@@ -1159,7 +1159,9 @@ int ast_mode_init(struct drm_device *dev)
 
 void ast_mode_fini(struct drm_device *dev)
 {
-	ast_cursor_fini(dev);
+	struct ast_private *ast = to_ast_private(dev);
+
+	ast_cursor_fini(ast);
 }
 
 static int get_clock(void *i2c_priv)
Signature · 6 lines
2.27.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#3 lore raw

PATCH v2 3/14 drm/ast: Move cursor fb pinning and mapping into helper

In reply to Thomas Zimmermann

The new helper ast_cursor_blit() updates a cursor's backbuffer HW BO from a framebuffer structure. The cursor plane's prepare_fb() function now uses the new interface.

Pinning and mapping of BOs is done automatically by the helper. This includes the source BO, which was not pinned by the original code in prepare_fb().

---
 drivers/gpu/drm/ast/ast_cursor.c | 57 ++++++++++++++++++++++++++++++--
 drivers/gpu/drm/ast/ast_drv.h    |  3 +-
 drivers/gpu/drm/ast/ast_mode.c   | 41 ++---------------------
 3 files changed, 59 insertions(+), 42 deletions(-)
drivers/gpu/drm/ast/ast_cursor.c +55 -2
index 1d4f51a7fe22..8f94d4712f66 100644
@@ -140,8 +140,8 @@ static u32 copy_cursor_image(u8 *src, u8 *dst, int width, int height)
 	return csum;
 }
 
-int ast_cursor_update(void *dst, void *src, unsigned int width,
-		      unsigned int height)
+static int ast_cursor_update(void *dst, void *src, unsigned int width,
+			     unsigned int height)
 {
 	u32 csum;
 
@@ -159,6 +159,59 @@ int ast_cursor_update(void *dst, void *src, unsigned int width,
 	return 0;
 }
 
+int ast_cursor_blit(struct ast_private *ast, struct drm_framebuffer *fb)
+{
+	struct drm_device *dev = ast->dev;
+	struct drm_gem_vram_object *gbo;
+	int ret;
+	void *src;
+	void *dst;
+
+	if (drm_WARN_ON_ONCE(dev, fb->width > AST_MAX_HWC_WIDTH) ||
+	    drm_WARN_ON_ONCE(dev, fb->height > AST_MAX_HWC_HEIGHT))
+		return -EINVAL;
+
+	gbo = drm_gem_vram_of_gem(fb->obj[0]);
+
+	ret = drm_gem_vram_pin(gbo, 0);
+	if (ret)
+		return ret;
+	src = drm_gem_vram_vmap(gbo);
+	if (IS_ERR(src)) {
+		ret = PTR_ERR(src);
+		goto err_drm_gem_vram_unpin;
+	}
+
+	dst = drm_gem_vram_vmap(ast->cursor.gbo[ast->cursor.next_index]);
+	if (IS_ERR(dst)) {
+		ret = PTR_ERR(dst);
+		goto err_drm_gem_vram_vunmap_src;
+	}
+
+	ret = ast_cursor_update(dst, src, fb->width, fb->height);
+	if (ret)
+		goto err_drm_gem_vram_vunmap_dst;
+
+	/*
+	 * Always unmap buffers here. Destination buffers are
+	 * perma-pinned while the driver is active. We're only
+	 * changing ref-counters here.
+	 */
+	drm_gem_vram_vunmap(ast->cursor.gbo[ast->cursor.next_index], dst);
+	drm_gem_vram_vunmap(gbo, src);
+	drm_gem_vram_unpin(gbo);
+
+	return 0;
+
+err_drm_gem_vram_vunmap_dst:
+	drm_gem_vram_vunmap(ast->cursor.gbo[ast->cursor.next_index], dst);
+err_drm_gem_vram_vunmap_src:
+	drm_gem_vram_vunmap(gbo, src);
+err_drm_gem_vram_unpin:
+	drm_gem_vram_unpin(gbo);
+	return ret;
+}
+
 void ast_cursor_set_base(struct ast_private *ast, u64 address)
 {
 	u8 addr0 = (address >> 3) & 0xff;
drivers/gpu/drm/ast/ast_drv.h +1 -2
index f7b120f862a8..9bc1bb76ec91 100644
@@ -318,8 +318,7 @@ void ast_release_firmware(struct drm_device *dev);
 /* ast_cursor.c */
 int ast_cursor_init(struct ast_private *ast);
 void ast_cursor_fini(struct ast_private *ast);
-int ast_cursor_update(void *dst, void *src, unsigned int width,
-		      unsigned int height);
+int ast_cursor_blit(struct ast_private *ast, struct drm_framebuffer *fb);
 void ast_cursor_set_base(struct ast_private *ast, u64 address);
 int ast_cursor_move(struct drm_crtc *crtc, int x, int y);
 
drivers/gpu/drm/ast/ast_mode.c +3 -38

59 lines not on this page · raw message

Signature · 6 lines
2.27.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#4 lore raw

PATCH v2 4/14 drm/ast: Update cursor image and checksum from same function

In reply to Thomas Zimmermann

Cursor image and checksum go hand in hand. Update both in the same place. The helper cannot fail, so remove the return type.

---
 drivers/gpu/drm/ast/ast_cursor.c | 24 +++++-------------------
 1 file changed, 5 insertions(+), 19 deletions(-)
drivers/gpu/drm/ast/ast_cursor.c +5 -19
index 8f94d4712f66..7474baddf048 100644
@@ -84,7 +84,7 @@ void ast_cursor_fini(struct ast_private *ast)
 	}
 }
 
-static u32 copy_cursor_image(u8 *src, u8 *dst, int width, int height)
+static void update_cursor_image(u8 __iomem *dst, const u8 *src, int width, int height)
 {
 	union {
 		u32 ul;
@@ -96,7 +96,8 @@ static u32 copy_cursor_image(u8 *src, u8 *dst, int width, int height)
 	} data16;
 	u32 csum = 0;
 	s32 alpha_dst_delta, last_alpha_dst_delta;
-	u8 *srcxor, *dstxor;
+	u8 __iomem *dstxor;
+	const u8 *srcxor;
 	int i, j;
 	u32 per_pixel_copy, two_pixel_copy;
 
@@ -137,16 +138,6 @@ static u32 copy_cursor_image(u8 *src, u8 *dst, int width, int height)
 		}
 		dstxor += last_alpha_dst_delta;
 	}
-	return csum;
-}
-
-static int ast_cursor_update(void *dst, void *src, unsigned int width,
-			     unsigned int height)
-{
-	u32 csum;
-
-	/* do data transfer to cursor cache */
-	csum = copy_cursor_image(src, dst, width, height);
 
 	/* write checksum + signature */
 	dst += AST_HWC_SIZE;
@@ -155,8 +146,6 @@ static int ast_cursor_update(void *dst, void *src, unsigned int width,
 	writel(height, dst + AST_HWC_SIGNATURE_SizeY);
 	writel(0, dst + AST_HWC_SIGNATURE_HOTSPOTX);
 	writel(0, dst + AST_HWC_SIGNATURE_HOTSPOTY);
-
-	return 0;
 }
 
 int ast_cursor_blit(struct ast_private *ast, struct drm_framebuffer *fb)
@@ -188,9 +177,8 @@ int ast_cursor_blit(struct ast_private *ast, struct drm_framebuffer *fb)
 		goto err_drm_gem_vram_vunmap_src;
 	}
 
-	ret = ast_cursor_update(dst, src, fb->width, fb->height);
-	if (ret)
-		goto err_drm_gem_vram_vunmap_dst;
+	/* do data transfer to cursor BO */
+	update_cursor_image(dst, src, fb->width, fb->height);
 
 	/*
 	 * Always unmap buffers here. Destination buffers are
@@ -203,8 +191,6 @@ int ast_cursor_blit(struct ast_private *ast, struct drm_framebuffer *fb)
 
 	return 0;
 
-err_drm_gem_vram_vunmap_dst:
-	drm_gem_vram_vunmap(ast->cursor.gbo[ast->cursor.next_index], dst);
 err_drm_gem_vram_vunmap_src:
 	drm_gem_vram_vunmap(gbo, src);
 err_drm_gem_vram_unpin:
Signature · 6 lines
2.27.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#5 lore raw

PATCH v2 5/14 drm/ast: Move cursor pageflip into helper

In reply to Thomas Zimmermann

The new helper ast_cursor_page_flip() switches the cursor's front and back BOs. This simplifies the cursor plane's update helper.

---
 drivers/gpu/drm/ast/ast_cursor.c | 20 +++++++++++++++++++-
 drivers/gpu/drm/ast/ast_drv.h    |  2 +-
 drivers/gpu/drm/ast/ast_mode.c   | 12 +-----------
 3 files changed, 21 insertions(+), 13 deletions(-)
drivers/gpu/drm/ast/ast_cursor.c +19 -1
index 7474baddf048..815d95b2f392 100644
@@ -198,7 +198,7 @@ int ast_cursor_blit(struct ast_private *ast, struct drm_framebuffer *fb)
 	return ret;
 }
 
-void ast_cursor_set_base(struct ast_private *ast, u64 address)
+static void ast_cursor_set_base(struct ast_private *ast, u64 address)
 {
 	u8 addr0 = (address >> 3) & 0xff;
 	u8 addr1 = (address >> 11) & 0xff;
@@ -209,6 +209,24 @@ void ast_cursor_set_base(struct ast_private *ast, u64 address)
 	ast_set_index_reg(ast, AST_IO_CRTC_PORT, 0xca, addr2);
 }
 
+void ast_cursor_page_flip(struct ast_private *ast)
+{
+	struct drm_device *dev = ast->dev;
+	struct drm_gem_vram_object *gbo;
+	s64 off;
+
+	gbo = ast->cursor.gbo[ast->cursor.next_index];
+
+	off = drm_gem_vram_offset(gbo);
+	if (drm_WARN_ON_ONCE(dev, off < 0))
+		return; /* Bug: we didn't pin the cursor HW BO to VRAM. */
+
+	ast_cursor_set_base(ast, off);
+
+	++ast->cursor.next_index;
+	ast->cursor.next_index %= ARRAY_SIZE(ast->cursor.gbo);
+}
+
 int ast_cursor_move(struct drm_crtc *crtc, int x, int y)
 {
 	struct ast_crtc *ast_crtc = to_ast_crtc(crtc);
drivers/gpu/drm/ast/ast_drv.h +1 -1
index 9bc1bb76ec91..e973c1ab96cb 100644
@@ -319,7 +319,7 @@ void ast_release_firmware(struct drm_device *dev);
 int ast_cursor_init(struct ast_private *ast);
 void ast_cursor_fini(struct ast_private *ast);
 int ast_cursor_blit(struct ast_private *ast, struct drm_framebuffer *fb);
-void ast_cursor_set_base(struct ast_private *ast, u64 address);
+void ast_cursor_page_flip(struct ast_private *ast);
 int ast_cursor_move(struct drm_crtc *crtc, int x, int y);
 
 #endif
drivers/gpu/drm/ast/ast_mode.c +1 -11
index 701211050832..32365f16c78c 100644
@@ -660,14 +660,11 @@ static void
 ast_cursor_plane_helper_atomic_update(struct drm_plane *plane,
 				      struct drm_plane_state *old_state)
 {
-	struct drm_device *dev = plane->dev;
 	struct drm_plane_state *state = plane->state;
 	struct drm_crtc *crtc = state->crtc;
 	struct drm_framebuffer *fb = state->fb;
 	struct ast_private *ast = to_ast_private(plane->dev);
 	struct ast_crtc *ast_crtc = to_ast_crtc(crtc);
-	struct drm_gem_vram_object *gbo;
-	s64 off;
 	u8 jreg;
 
 	ast_crtc->offset_x = AST_MAX_HWC_WIDTH - fb->width;
@@ -675,14 +672,7 @@ ast_cursor_plane_helper_atomic_update(struct drm_plane *plane,
 
 	if (state->fb != old_state->fb) {
 		/* A new cursor image was installed. */
-		gbo = ast->cursor.gbo[ast->cursor.next_index];
-		off = drm_gem_vram_offset(gbo);
-		if (drm_WARN_ON_ONCE(dev, off < 0))
-			return; /* Bug: we didn't pin cursor HW BO to VRAM. */
-		ast_cursor_set_base(ast, off);
-
-		++ast->cursor.next_index;
-		ast->cursor.next_index %= ARRAY_SIZE(ast->cursor.gbo);
+		ast_cursor_page_flip(ast);
 	}
 
 	ast_cursor_move(crtc, state->crtc_x, state->crtc_y);
Signature · 6 lines
2.27.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#6 lore raw

PATCH v2 6/14 drm/ast: Replace ast_cursor_move() with ast_cursor_show()

In reply to Thomas Zimmermann

Having a cursor move function is misleading, as it actually enables the cursor's image for displaying. So rename it to ast_cursor_show(). It's semantics is to show a cursor at the specified location on the screen. The displayed cursor is always the image in the cursor front BO.

This change also simplifies struct ast_crtc to being a mere wrapper around around struct drm_crtc. It will be removed by a later patch.

---
 drivers/gpu/drm/ast/ast_cursor.c | 42 ++++++++++++++++++++------------
 drivers/gpu/drm/ast/ast_drv.h    |  4 +--
 drivers/gpu/drm/ast/ast_mode.c   | 12 ++++-----
 3 files changed, 35 insertions(+), 23 deletions(-)
drivers/gpu/drm/ast/ast_cursor.c +27 -15
index 815d95b2f392..8f8fdc831830 100644
@@ -227,12 +227,27 @@ void ast_cursor_page_flip(struct ast_private *ast)
 	ast->cursor.next_index %= ARRAY_SIZE(ast->cursor.gbo);
 }
 
-int ast_cursor_move(struct drm_crtc *crtc, int x, int y)
+static void ast_cursor_set_location(struct ast_private *ast, u16 x, u16 y,
+				    u8 x_offset, u8 y_offset)
+{
+	u8 x0 = (x & 0x00ff);
+	u8 x1 = (x & 0x0f00) >> 8;
+	u8 y0 = (y & 0x00ff);
+	u8 y1 = (y & 0x0700) >> 8;
+
+	ast_set_index_reg(ast, AST_IO_CRTC_PORT, 0xc2, x_offset);
+	ast_set_index_reg(ast, AST_IO_CRTC_PORT, 0xc3, y_offset);
+	ast_set_index_reg(ast, AST_IO_CRTC_PORT, 0xc4, x0);
+	ast_set_index_reg(ast, AST_IO_CRTC_PORT, 0xc5, x1);
+	ast_set_index_reg(ast, AST_IO_CRTC_PORT, 0xc6, y0);
+	ast_set_index_reg(ast, AST_IO_CRTC_PORT, 0xc7, y1);
+}
+
+int ast_cursor_show(struct ast_private *ast, int x, int y,
+		    unsigned int offset_x, unsigned int offset_y)
 {
-	struct ast_crtc *ast_crtc = to_ast_crtc(crtc);
-	struct ast_private *ast = to_ast_private(crtc->dev);
 	struct drm_gem_vram_object *gbo;
-	int x_offset, y_offset;
+	u8 x_offset, y_offset;
 	u8 *dst, *sig;
 	u8 jreg;
 
@@ -245,23 +260,20 @@ int ast_cursor_move(struct drm_crtc *crtc, int x, int y)
 	writel(x, sig + AST_HWC_SIGNATURE_X);
 	writel(y, sig + AST_HWC_SIGNATURE_Y);
 
-	x_offset = ast_crtc->offset_x;
-	y_offset = ast_crtc->offset_y;
 	if (x < 0) {
-		x_offset = (-x) + ast_crtc->offset_x;
+		x_offset = (-x) + offset_x;
 		x = 0;
+	} else {
+		x_offset = offset_x;
 	}
-
 	if (y < 0) {
-		y_offset = (-y) + ast_crtc->offset_y;
+		y_offset = (-y) + offset_y;
 		y = 0;
+	} else {
+		y_offset = offset_y;
 	}
-	ast_set_index_reg(ast, AST_IO_CRTC_PORT, 0xc2, x_offset);
-	ast_set_index_reg(ast, AST_IO_CRTC_PORT, 0xc3, y_offset);
-	ast_set_index_reg(ast, AST_IO_CRTC_PORT, 0xc4, (x & 0xff));
-	ast_set_index_reg(ast, AST_IO_CRTC_PORT, 0xc5, ((x >> 8) & 0x0f));
-	ast_set_index_reg(ast, AST_IO_CRTC_PORT, 0xc6, (y & 0xff));
-	ast_set_index_reg(ast, AST_IO_CRTC_PORT, 0xc7, ((y >> 8) & 0x07));
+
+	ast_cursor_set_location(ast, x, y, x_offset, y_offset);
 
 	/* dummy write to fire HWC */
 	jreg = 0x02 |
drivers/gpu/drm/ast/ast_drv.h +2 -2
index e973c1ab96cb..b00091798ef5 100644
@@ -239,7 +239,6 @@ struct ast_connector {
 
 struct ast_crtc {
 	struct drm_crtc base;
-	u8 offset_x, offset_y;
 };
 
 #define to_ast_crtc(x) container_of(x, struct ast_crtc, base)
@@ -320,6 +319,7 @@ int ast_cursor_init(struct ast_private *ast);
 void ast_cursor_fini(struct ast_private *ast);
 int ast_cursor_blit(struct ast_private *ast, struct drm_framebuffer *fb);
 void ast_cursor_page_flip(struct ast_private *ast);
-int ast_cursor_move(struct drm_crtc *crtc, int x, int y);
+int ast_cursor_show(struct ast_private *ast, int x, int y,
+		    unsigned int offset_x, unsigned int offset_y);
 
 #endif
drivers/gpu/drm/ast/ast_mode.c +6 -6
index 32365f16c78c..b452f9e28d7c 100644
@@ -661,21 +661,21 @@ ast_cursor_plane_helper_atomic_update(struct drm_plane *plane,
 				      struct drm_plane_state *old_state)
 {
 	struct drm_plane_state *state = plane->state;
-	struct drm_crtc *crtc = state->crtc;
 	struct drm_framebuffer *fb = state->fb;
-	struct ast_private *ast = to_ast_private(plane->dev);
-	struct ast_crtc *ast_crtc = to_ast_crtc(crtc);
+	struct ast_private *ast = plane->dev->dev_private;
+	unsigned int offset_x, offset_y;
 	u8 jreg;
 
-	ast_crtc->offset_x = AST_MAX_HWC_WIDTH - fb->width;
-	ast_crtc->offset_y = AST_MAX_HWC_WIDTH - fb->height;
+	offset_x = AST_MAX_HWC_WIDTH - fb->width;
+	offset_y = AST_MAX_HWC_WIDTH - fb->height;
 
 	if (state->fb != old_state->fb) {
 		/* A new cursor image was installed. */
 		ast_cursor_page_flip(ast);
 	}
 
-	ast_cursor_move(crtc, state->crtc_x, state->crtc_y);
+	ast_cursor_show(ast, state->crtc_x, state->crtc_y,
+			offset_x, offset_y);
 
 	jreg = 0x2;
 	/* enable ARGB cursor */
Signature · 6 lines
2.27.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#7 lore raw

PATCH v2 7/14 drm/ast: Don't enable HW cursors twice during atomic update

In reply to Thomas Zimmermann

The ast_cursor_show() helper enables the cursor to be displayed. No need to repeat that operation in the plane's atomic-update function.

---
 drivers/gpu/drm/ast/ast_mode.c | 6 ------
 1 file changed, 6 deletions(-)
drivers/gpu/drm/ast/ast_mode.c +0 -6
index b452f9e28d7c..5c41a91f5630 100644
@@ -664,7 +664,6 @@ ast_cursor_plane_helper_atomic_update(struct drm_plane *plane,
 	struct drm_framebuffer *fb = state->fb;
 	struct ast_private *ast = plane->dev->dev_private;
 	unsigned int offset_x, offset_y;
-	u8 jreg;
 
 	offset_x = AST_MAX_HWC_WIDTH - fb->width;
 	offset_y = AST_MAX_HWC_WIDTH - fb->height;
@@ -676,11 +675,6 @@ ast_cursor_plane_helper_atomic_update(struct drm_plane *plane,
 
 	ast_cursor_show(ast, state->crtc_x, state->crtc_y,
 			offset_x, offset_y);
-
-	jreg = 0x2;
-	/* enable ARGB cursor */
-	jreg |= 1;
-	ast_set_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xcb, 0xfc, jreg);
 }
 
 static void
Signature · 6 lines
2.27.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#8 lore raw

PATCH v2 8/14 drm/ast: Add helper to hide cursor

In reply to Thomas Zimmermann

As the inverse to ast_cursor_show(), ast_cursor_hide() disables the HW cursor.

---
 drivers/gpu/drm/ast/ast_cursor.c | 5 +++++
 drivers/gpu/drm/ast/ast_drv.h    | 1 +
 drivers/gpu/drm/ast/ast_mode.c   | 2 +-
 3 files changed, 7 insertions(+), 1 deletion(-)
drivers/gpu/drm/ast/ast_cursor.c +5 -0
index 8f8fdc831830..5421241015d6 100644
@@ -284,3 +284,8 @@ int ast_cursor_show(struct ast_private *ast, int x, int y,
 
 	return 0;
 }
+
+void ast_cursor_hide(struct ast_private *ast)
+{
+	ast_set_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xcb, 0xfc, 0x00);
+}
drivers/gpu/drm/ast/ast_drv.h +1 -0
index b00091798ef5..92af0637ac48 100644
@@ -321,5 +321,6 @@ int ast_cursor_blit(struct ast_private *ast, struct drm_framebuffer *fb);
 void ast_cursor_page_flip(struct ast_private *ast);
 int ast_cursor_show(struct ast_private *ast, int x, int y,
 		    unsigned int offset_x, unsigned int offset_y);
+void ast_cursor_hide(struct ast_private *ast);
 
 #endif
drivers/gpu/drm/ast/ast_mode.c +1 -1
index 5c41a91f5630..8fdc46401814 100644
@@ -683,7 +683,7 @@ ast_cursor_plane_helper_atomic_disable(struct drm_plane *plane,
 {
 	struct ast_private *ast = to_ast_private(plane->dev);
 
-	ast_set_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xcb, 0xfc, 0x00);
+	ast_cursor_hide(ast);
 }
 
 static const struct drm_plane_helper_funcs ast_cursor_plane_helper_funcs = {
Signature · 6 lines
2.27.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#9 lore raw

PATCH v2 9/14 drm/ast: Keep cursor HW BOs mapped

In reply to Thomas Zimmermann

Updating the image in a cursor's HW BO requires a mapping of the BO's buffer in the kernel's address space. Cursor image updates can happen frequently and create CPU overhead.

As cursor HW BOs are small and never move, they are now map exactly once during the initialization and the mapping is used throughout the driver's lifetime.

This change also removes a possible source of failures from ast_cursor_show(). As the helper does not establish mappings, it cannot fail. As a result, the cursor plane's atomic-update helper does not call any failable interfaces. All failures are detected before trying to update the cursor plane.

---
 drivers/gpu/drm/ast/ast_cursor.c | 44 +++++++++++++-------------------
 drivers/gpu/drm/ast/ast_drv.h    |  5 ++--
 2 files changed, 21 insertions(+), 28 deletions(-)
drivers/gpu/drm/ast/ast_cursor.c +18 -26
index 5421241015d6..35680402e410 100644
@@ -39,6 +39,7 @@ int ast_cursor_init(struct ast_private *ast)
 	struct drm_device *dev = ast->dev;
 	size_t size, i;
 	struct drm_gem_vram_object *gbo;
+	void __iomem *vaddr;
 	int ret;
 
 	size = roundup(AST_HWC_SIZE + AST_HWC_SIGNATURE_SIZE, PAGE_SIZE);
@@ -55,8 +56,16 @@ int ast_cursor_init(struct ast_private *ast)
 			drm_gem_vram_put(gbo);
 			goto err_drm_gem_vram_put;
 		}
+		vaddr = drm_gem_vram_vmap(gbo);
+		if (IS_ERR(vaddr)) {
+			ret = PTR_ERR(vaddr);
+			drm_gem_vram_unpin(gbo);
+			drm_gem_vram_put(gbo);
+			goto err_drm_gem_vram_put;
+		}
 
 		ast->cursor.gbo[i] = gbo;
+		ast->cursor.vaddr[i] = vaddr;
 	}
 
 	return 0;
@@ -65,9 +74,11 @@ int ast_cursor_init(struct ast_private *ast)
 	while (i) {
 		--i;
 		gbo = ast->cursor.gbo[i];
+		drm_gem_vram_vunmap(gbo, ast->cursor.vaddr[i]);
 		drm_gem_vram_unpin(gbo);
 		drm_gem_vram_put(gbo);
 		ast->cursor.gbo[i] = NULL;
+		ast->cursor.vaddr[i] = NULL;
 	}
 	return ret;
 }
@@ -79,6 +90,7 @@ void ast_cursor_fini(struct ast_private *ast)
 
 	for (i = 0; i < ARRAY_SIZE(ast->cursor.gbo); ++i) {
 		gbo = ast->cursor.gbo[i];
+		drm_gem_vram_vunmap(gbo, ast->cursor.vaddr[i]);
 		drm_gem_vram_unpin(gbo);
 		drm_gem_vram_put(gbo);
 	}
@@ -154,7 +166,7 @@ int ast_cursor_blit(struct ast_private *ast, struct drm_framebuffer *fb)
 	struct drm_gem_vram_object *gbo;
 	int ret;
 	void *src;
-	void *dst;
+	void __iomem *dst;
 
 	if (drm_WARN_ON_ONCE(dev, fb->width > AST_MAX_HWC_WIDTH) ||
 	    drm_WARN_ON_ONCE(dev, fb->height > AST_MAX_HWC_HEIGHT))
@@ -171,28 +183,16 @@ int ast_cursor_blit(struct ast_private *ast, struct drm_framebuffer *fb)
 		goto err_drm_gem_vram_unpin;
 	}
 
-	dst = drm_gem_vram_vmap(ast->cursor.gbo[ast->cursor.next_index]);
-	if (IS_ERR(dst)) {
-		ret = PTR_ERR(dst);
-		goto err_drm_gem_vram_vunmap_src;
-	}
+	dst = ast->cursor.vaddr[ast->cursor.next_index];
 
 	/* do data transfer to cursor BO */
 	update_cursor_image(dst, src, fb->width, fb->height);
 
-	/*
-	 * Always unmap buffers here. Destination buffers are
-	 * perma-pinned while the driver is active. We're only
-	 * changing ref-counters here.
-	 */
-	drm_gem_vram_vunmap(ast->cursor.gbo[ast->cursor.next_index], dst);
 	drm_gem_vram_vunmap(gbo, src);
 	drm_gem_vram_unpin(gbo);
 
 	return 0;
 
-err_drm_gem_vram_vunmap_src:
-	drm_gem_vram_vunmap(gbo, src);
 err_drm_gem_vram_unpin:
 	drm_gem_vram_unpin(gbo);
 	return ret;
@@ -243,18 +243,14 @@ static void ast_cursor_set_location(struct ast_private *ast, u16 x, u16 y,
 	ast_set_index_reg(ast, AST_IO_CRTC_PORT, 0xc7, y1);
 }
 
-int ast_cursor_show(struct ast_private *ast, int x, int y,
-		    unsigned int offset_x, unsigned int offset_y)
+void ast_cursor_show(struct ast_private *ast, int x, int y,
+		     unsigned int offset_x, unsigned int offset_y)
 {
-	struct drm_gem_vram_object *gbo;
 	u8 x_offset, y_offset;
-	u8 *dst, *sig;
+	u8 __iomem *dst, __iomem *sig;
 	u8 jreg;
 
-	gbo = ast->cursor.gbo[ast->cursor.next_index];
-	dst = drm_gem_vram_vmap(gbo);
-	if (IS_ERR(dst))
-		return PTR_ERR(dst);
+	dst = ast->cursor.vaddr[ast->cursor.next_index];
 
 	sig = dst + AST_HWC_SIZE;
 	writel(x, sig + AST_HWC_SIGNATURE_X);
@@ -279,10 +275,6 @@ int ast_cursor_show(struct ast_private *ast, int x, int y,
 	jreg = 0x02 |
 	       0x01; /* enable ARGB4444 cursor */
 	ast_set_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xcb, 0xfc, jreg);
-
-	drm_gem_vram_vunmap(gbo, dst);
-
-	return 0;
 }
 
 void ast_cursor_hide(struct ast_private *ast)
drivers/gpu/drm/ast/ast_drv.h +3 -2
index 92af0637ac48..f465e0c0984b 100644
@@ -116,6 +116,7 @@ struct ast_private {
 
 	struct {
 		struct drm_gem_vram_object *gbo[AST_DEFAULT_HWC_NUM];
+		void __iomem *vaddr[AST_DEFAULT_HWC_NUM];
 		unsigned int next_index;
 	} cursor;
 
@@ -319,8 +320,8 @@ int ast_cursor_init(struct ast_private *ast);
 void ast_cursor_fini(struct ast_private *ast);
 int ast_cursor_blit(struct ast_private *ast, struct drm_framebuffer *fb);
 void ast_cursor_page_flip(struct ast_private *ast);
-int ast_cursor_show(struct ast_private *ast, int x, int y,
-		    unsigned int offset_x, unsigned int offset_y);
+void ast_cursor_show(struct ast_private *ast, int x, int y,
+		     unsigned int offset_x, unsigned int offset_y);
 void ast_cursor_hide(struct ast_private *ast);
 
 #endif
Signature · 6 lines
2.27.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#10 lore raw

PATCH v2 10/14 drm/ast: Managed cursor release

In reply to Thomas Zimmermann

Register a release function to finalize cursors. The _fini() function gets un-exported from the source file.

The function ast_mode_fini() is now empty and will be removed by a later patch.

---
 drivers/gpu/drm/ast/ast_cursor.c | 38 ++++++++++++++++++--------------
 drivers/gpu/drm/ast/ast_drv.h    |  1 -
 drivers/gpu/drm/ast/ast_mode.c   |  3 ---
 3 files changed, 22 insertions(+), 20 deletions(-)
drivers/gpu/drm/ast/ast_cursor.c +22 -16
index 35680402e410..acf0d23514e8 100644
@@ -28,9 +28,30 @@
  */
 
 #include <drm/drm_gem_vram_helper.h>
+#include <drm/drm_managed.h>
 
 #include "ast_drv.h"
 
+static void ast_cursor_fini(struct ast_private *ast)
+{
+	size_t i;
+	struct drm_gem_vram_object *gbo;
+
+	for (i = 0; i < ARRAY_SIZE(ast->cursor.gbo); ++i) {
+		gbo = ast->cursor.gbo[i];
+		drm_gem_vram_vunmap(gbo, ast->cursor.vaddr[i]);
+		drm_gem_vram_unpin(gbo);
+		drm_gem_vram_put(gbo);
+	}
+}
+
+static void ast_cursor_release(struct drm_device *dev, void *ptr)
+{
+	struct ast_private *ast = dev->dev_private;
+
+	ast_cursor_fini(ast);
+}
+
 /*
  * Allocate cursor BOs and pins them at the end of VRAM.
  */
@@ -68,7 +89,7 @@ int ast_cursor_init(struct ast_private *ast)
 		ast->cursor.vaddr[i] = vaddr;
 	}
 
-	return 0;
+	return drmm_add_action_or_reset(dev, ast_cursor_release, NULL);
 
 err_drm_gem_vram_put:
 	while (i) {
@@ -77,25 +98,10 @@ int ast_cursor_init(struct ast_private *ast)
 		drm_gem_vram_vunmap(gbo, ast->cursor.vaddr[i]);
 		drm_gem_vram_unpin(gbo);
 		drm_gem_vram_put(gbo);
-		ast->cursor.gbo[i] = NULL;
-		ast->cursor.vaddr[i] = NULL;
 	}
 	return ret;
 }
 
-void ast_cursor_fini(struct ast_private *ast)
-{
-	size_t i;
-	struct drm_gem_vram_object *gbo;
-
-	for (i = 0; i < ARRAY_SIZE(ast->cursor.gbo); ++i) {
-		gbo = ast->cursor.gbo[i];
-		drm_gem_vram_vunmap(gbo, ast->cursor.vaddr[i]);
-		drm_gem_vram_unpin(gbo);
-		drm_gem_vram_put(gbo);
-	}
-}
-
 static void update_cursor_image(u8 __iomem *dst, const u8 *src, int width, int height)
 {
 	union {
drivers/gpu/drm/ast/ast_drv.h +0 -1
index f465e0c0984b..ea4de3dce2c4 100644
@@ -317,7 +317,6 @@ void ast_release_firmware(struct drm_device *dev);
 
 /* ast_cursor.c */
 int ast_cursor_init(struct ast_private *ast);
-void ast_cursor_fini(struct ast_private *ast);
 int ast_cursor_blit(struct ast_private *ast, struct drm_framebuffer *fb);
 void ast_cursor_page_flip(struct ast_private *ast);
 void ast_cursor_show(struct ast_private *ast, int x, int y,
drivers/gpu/drm/ast/ast_mode.c +0 -3
index 8fdc46401814..4724a38c001a 100644
@@ -1108,9 +1108,6 @@ int ast_mode_init(struct drm_device *dev)
 
 void ast_mode_fini(struct drm_device *dev)
 {
-	struct ast_private *ast = to_ast_private(dev);
-
-	ast_cursor_fini(ast);
 }
 
 static int get_clock(void *i2c_priv)
Signature · 6 lines
2.27.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#11 lore raw

PATCH v2 11/14 drm/ast: Init cursors before creating modesetting structures

In reply to Thomas Zimmermann

The cursor helpers reserve buffer objects in VRAM and update their content. So although tied to modesetting, cursor helpers are more of a memory manager. The modesetting's cursor plane requires this functionality, so initialize cursors before modesetting.

While at it, also add an error check for ast_cursor_init().

---
 drivers/gpu/drm/ast/ast_mode.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/gpu/drm/ast/ast_mode.c +4 -1
index 4724a38c001a..89d9ee0a9e81 100644
@@ -1073,6 +1073,10 @@ int ast_mode_init(struct drm_device *dev)
 	struct ast_private *ast = to_ast_private(dev);
 	int ret;
 
+	ret = ast_cursor_init(ast);
+	if (ret)
+		return ret;
+
 	memset(&ast->primary_plane, 0, sizeof(ast->primary_plane));
 	ret = drm_universal_plane_init(dev, &ast->primary_plane, 0x01,
 				       &ast_primary_plane_funcs,
@@ -1098,7 +1102,6 @@ int ast_mode_init(struct drm_device *dev)
 	drm_plane_helper_add(&ast->cursor_plane,
 			     &ast_cursor_plane_helper_funcs);
 
-	ast_cursor_init(ast);
 	ast_crtc_init(dev);
 	ast_encoder_init(dev);
 	ast_connector_init(dev);
Signature · 6 lines
2.27.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#12 lore raw

PATCH v2 12/14 drm/ast: Replace struct ast_crtc with struct drm_crtc

In reply to Thomas Zimmermann

Struct ast_crtc has been cleaned up and it's now a wrapper around the DRM CRTC structure struct drm_crtc. This patch converts the driver to struct drm_crtc and removes struct ast_crtc.

---
 drivers/gpu/drm/ast/ast_drv.h  |  5 -----
 drivers/gpu/drm/ast/ast_mode.c | 11 ++++++-----
 2 files changed, 6 insertions(+), 10 deletions(-)
drivers/gpu/drm/ast/ast_drv.h +0 -5
index ea4de3dce2c4..77226e2fd7c0 100644
@@ -238,11 +238,6 @@ struct ast_connector {
 	struct ast_i2c_chan *i2c;
 };
 
-struct ast_crtc {
-	struct drm_crtc base;
-};
-
-#define to_ast_crtc(x) container_of(x, struct ast_crtc, base)
 #define to_ast_connector(x) container_of(x, struct ast_connector, base)
 
 struct ast_vbios_stdtable {
drivers/gpu/drm/ast/ast_mode.c +6 -5
index 89d9ee0a9e81..43c9686ba0f7 100644
@@ -881,21 +881,22 @@ static const struct drm_crtc_funcs ast_crtc_funcs = {
 static int ast_crtc_init(struct drm_device *dev)
 {
 	struct ast_private *ast = to_ast_private(dev);
-	struct ast_crtc *crtc;
+	struct drm_crtc *crtc;
 	int ret;
 
-	crtc = kzalloc(sizeof(struct ast_crtc), GFP_KERNEL);
+	crtc = kzalloc(sizeof(*crtc), GFP_KERNEL);
 	if (!crtc)
 		return -ENOMEM;
 
-	ret = drm_crtc_init_with_planes(dev, &crtc->base, &ast->primary_plane,
+	ret = drm_crtc_init_with_planes(dev, crtc, &ast->primary_plane,
 					&ast->cursor_plane, &ast_crtc_funcs,
 					NULL);
 	if (ret)
 		goto err_kfree;
 
-	drm_mode_crtc_set_gamma_size(&crtc->base, 256);
-	drm_crtc_helper_add(&crtc->base, &ast_crtc_helper_funcs);
+	drm_mode_crtc_set_gamma_size(crtc, 256);
+	drm_crtc_helper_add(crtc, &ast_crtc_helper_funcs);
+
 	return 0;
 
 err_kfree:
Signature · 6 lines
2.27.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#13 lore raw

Re: [PATCH v2 12/14] drm/ast: Replace struct ast_crtc with struct drm_crtc

Hi Thomas.

Just browsing code..

Quoted 5 lines · Thomas Zimmermann

Struct ast_crtc has been cleaned up and it's now a wrapper around the DRM CRTC structure struct drm_crtc. This patch converts the driver to struct drm_crtc and removes struct ast_crtc.

Why is it we cannot embed struct drm_crtc?
And I also failed to see where is is de-allocated - but surely I miss something obvious here.

Sam

Quoted 60 lines
---
 drivers/gpu/drm/ast/ast_drv.h  |  5 -----
 drivers/gpu/drm/ast/ast_mode.c | 11 ++++++-----
 2 files changed, 6 insertions(+), 10 deletions(-)
drivers/gpu/drm/ast/ast_drv.h +0 -5
index ea4de3dce2c4..77226e2fd7c0 100644
@@ -238,11 +238,6 @@ struct ast_connector {
 	struct ast_i2c_chan *i2c;
 };
 
-struct ast_crtc {
-	struct drm_crtc base;
-};
-
-#define to_ast_crtc(x) container_of(x, struct ast_crtc, base)
 #define to_ast_connector(x) container_of(x, struct ast_connector, base)
 
 struct ast_vbios_stdtable {
drivers/gpu/drm/ast/ast_mode.c +6 -5
index 89d9ee0a9e81..43c9686ba0f7 100644
@@ -881,21 +881,22 @@ static const struct drm_crtc_funcs ast_crtc_funcs = {
 static int ast_crtc_init(struct drm_device *dev)
 {
 	struct ast_private *ast = to_ast_private(dev);
-	struct ast_crtc *crtc;
+	struct drm_crtc *crtc;
 	int ret;
 
-	crtc = kzalloc(sizeof(struct ast_crtc), GFP_KERNEL);
+	crtc = kzalloc(sizeof(*crtc), GFP_KERNEL);
 	if (!crtc)
 		return -ENOMEM;
 
-	ret = drm_crtc_init_with_planes(dev, &crtc->base, &ast->primary_plane,
+	ret = drm_crtc_init_with_planes(dev, crtc, &ast->primary_plane,
 					&ast->cursor_plane, &ast_crtc_funcs,
 					NULL);
 	if (ret)
 		goto err_kfree;
 
-	drm_mode_crtc_set_gamma_size(&crtc->base, 256);
-	drm_crtc_helper_add(&crtc->base, &ast_crtc_helper_funcs);
+	drm_mode_crtc_set_gamma_size(crtc, 256);
+	drm_crtc_helper_add(crtc, &ast_crtc_helper_funcs);
+
 	return 0;
 
 err_kfree:
Signature · 6 lines
2.27.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

author maintainer
#14 lore raw

Re: [PATCH v2 12/14] drm/ast: Replace struct ast_crtc with struct drm_crtc

Hi Sam

Am 03.07.20 um 08:38 schrieb Sam Ravnborg:

Quoted 4 lines

Hi Thomas.

Just browsing code..

Quoted 8 lines
Quoted 5 lines · Thomas Zimmermann

Struct ast_crtc has been cleaned up and it's now a wrapper around the DRM CRTC structure struct drm_crtc. This patch converts the driver to struct drm_crtc and removes struct ast_crtc.

Why is it we cannot embed struct drm_crtc?

I want to do that in a later patchset. The conversion to managed code is fairly large, so thought it might be better to do it in several rounds.

This patchset is only for modesetting. I have another patchset that converts the memory management to managed interfaces. After that the final patchset will address device structures. Embedding everything CRTC and other structures in struct ast_private would be part of this.

If you prefer a longer patchset that does everything, let me know.

Quoted 2 lines

And I also failed to see where is is de-allocated - but surely I miss something obvious here.

It's freed in ast_crtc_destroy().

Best regards
Thomas

Quoted 68 lines

Sam

Quoted 60 lines
---
 drivers/gpu/drm/ast/ast_drv.h  |  5 -----
 drivers/gpu/drm/ast/ast_mode.c | 11 ++++++-----
 2 files changed, 6 insertions(+), 10 deletions(-)
drivers/gpu/drm/ast/ast_drv.h +0 -5
index ea4de3dce2c4..77226e2fd7c0 100644
@@ -238,11 +238,6 @@ struct ast_connector {
 	struct ast_i2c_chan *i2c;
 };
 
-struct ast_crtc {
-	struct drm_crtc base;
-};
-
-#define to_ast_crtc(x) container_of(x, struct ast_crtc, base)
 #define to_ast_connector(x) container_of(x, struct ast_connector, base)
 
 struct ast_vbios_stdtable {
drivers/gpu/drm/ast/ast_mode.c +6 -5
index 89d9ee0a9e81..43c9686ba0f7 100644
@@ -881,21 +881,22 @@ static const struct drm_crtc_funcs ast_crtc_funcs = {
 static int ast_crtc_init(struct drm_device *dev)
 {
 	struct ast_private *ast = to_ast_private(dev);
-	struct ast_crtc *crtc;
+	struct drm_crtc *crtc;
 	int ret;
 
-	crtc = kzalloc(sizeof(struct ast_crtc), GFP_KERNEL);
+	crtc = kzalloc(sizeof(*crtc), GFP_KERNEL);
 	if (!crtc)
 		return -ENOMEM;
 
-	ret = drm_crtc_init_with_planes(dev, &crtc->base, &ast->primary_plane,
+	ret = drm_crtc_init_with_planes(dev, crtc, &ast->primary_plane,
 					&ast->cursor_plane, &ast_crtc_funcs,
 					NULL);
 	if (ret)
 		goto err_kfree;
 
-	drm_mode_crtc_set_gamma_size(&crtc->base, 256);
-	drm_crtc_helper_add(&crtc->base, &ast_crtc_helper_funcs);
+	drm_mode_crtc_set_gamma_size(crtc, 256);
+	drm_crtc_helper_add(crtc, &ast_crtc_helper_funcs);
+
 	return 0;
 
 err_kfree:
Signature · 6 lines
2.27.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Signature · 6 lines
Thomas Zimmermann
Graphics Driver Developer
SUSE Software Solutions Germany GmbH
Maxfeldstr. 5, 90409 Nürnberg, Germany
(HRB 36809, AG Nürnberg)
Geschäftsführer: Felix Imendörffer

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

#15 lore raw

Re: [PATCH v2 12/14] drm/ast: Replace struct ast_crtc with struct drm_crtc

Hi Thomas.

Quoted 12 lines · Thomas Zimmermann

Hi Sam

Am 03.07.20 um 08:38 schrieb Sam Ravnborg:

Quoted 9 lines

Hi Thomas.

Just browsing code..

Quoted 4 lines · Thomas Zimmermann

Struct ast_crtc has been cleaned up and it's now a wrapper around the DRM CRTC structure struct drm_crtc. This patch converts the driver to struct drm_crtc and removes struct ast_crtc.

Quoted 6 lines
Quoted 3 lines
Quoted 1 line

Why is it we cannot embed struct drm_crtc?

I want to do that in a later patchset. The conversion to managed code is fairly large, so thought it might be better to do it in several rounds.

Understood, and several rounds are good.

Quoted 6 lines

This patchset is only for modesetting. I have another patchset that converts the memory management to managed interfaces. After that the final patchset will address device structures. Embedding everything CRTC and other structures in struct ast_private would be part of this.

Quoted 6 lines

If you prefer a longer patchset that does everything, let me know.

Quoted 2 lines

And I also failed to see where is is de-allocated - but surely I miss something obvious here.

It's freed in ast_crtc_destroy().

Ohh, one of the places that worked/works because struct crtc was/is the first member.

I get it now, thanks for the explanation.

Sam
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

author maintainer
#16 lore raw

PATCH v2 13/14 drm/ast: Use managed mode-config init

In reply to Thomas Zimmermann

Using drmm_mode_config_init() sets up managed release of modesetting resources. The existing modesetting's finalizer is empty, so remove it.

---
 drivers/gpu/drm/ast/ast_drv.h  | 1 -
 drivers/gpu/drm/ast/ast_main.c | 6 +++---
 drivers/gpu/drm/ast/ast_mode.c | 4 ----
 3 files changed, 3 insertions(+), 8 deletions(-)
drivers/gpu/drm/ast/ast_drv.h +0 -1
index 77226e2fd7c0..ad1d0b14ef12 100644
@@ -287,7 +287,6 @@ struct ast_crtc_state {
 #define to_ast_crtc_state(state) container_of(state, struct ast_crtc_state, base)
 
 extern int ast_mode_init(struct drm_device *dev);
-extern void ast_mode_fini(struct drm_device *dev);
 
 #define AST_MM_ALIGN_SHIFT 4
 #define AST_MM_ALIGN_MASK ((1 << AST_MM_ALIGN_SHIFT) - 1)
drivers/gpu/drm/ast/ast_main.c +3 -3
index 2eab19a9056f..2642e6d0152b 100644
@@ -473,7 +473,9 @@ int ast_driver_load(struct drm_device *dev, unsigned long flags)
 	if (ret)
 		goto out_free;
 
-	drm_mode_config_init(dev);
+	ret = drmm_mode_config_init(dev);
+	if (ret)
+		goto out_free;
 
 	dev->mode_config.funcs = (void *)&ast_mode_funcs;
 	dev->mode_config.min_width = 0;
@@ -516,8 +518,6 @@ void ast_driver_unload(struct drm_device *dev)
 
 	ast_release_firmware(dev);
 	kfree(ast->dp501_fw_addr);
-	ast_mode_fini(dev);
-	drm_mode_config_cleanup(dev);
 
 	ast_mm_fini(ast);
 	kfree(ast);
drivers/gpu/drm/ast/ast_mode.c +0 -4
index 43c9686ba0f7..33b4b6f3e394 100644
@@ -1110,10 +1110,6 @@ int ast_mode_init(struct drm_device *dev)
 	return 0;
 }
 
-void ast_mode_fini(struct drm_device *dev)
-{
-}
-
 static int get_clock(void *i2c_priv)
 {
 	struct ast_i2c_chan *i2c = i2c_priv;
Signature · 6 lines
2.27.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#17 lore raw

PATCH v2 14/14 drm/ast: Initialize mode setting in ast_mode_config_init()

In reply to Thomas Zimmermann

There's modesetting init code in ast_main.c. Move it to ast_mode.c and merge it with the modesetting init code in ast_mode_init(). The result is ast_mode_config_init(), which initalizes the whole modesetting.

---
 drivers/gpu/drm/ast/ast_drv.h  |  2 +-
 drivers/gpu/drm/ast/ast_main.c | 35 +----------------------------
 drivers/gpu/drm/ast/ast_mode.c | 41 ++++++++++++++++++++++++++++++++--
 3 files changed, 41 insertions(+), 37 deletions(-)
drivers/gpu/drm/ast/ast_drv.h +1 -1
index ad1d0b14ef12..c8c442e9efdc 100644
@@ -286,7 +286,7 @@ struct ast_crtc_state {
 
 #define to_ast_crtc_state(state) container_of(state, struct ast_crtc_state, base)
 
-extern int ast_mode_init(struct drm_device *dev);
+int ast_mode_config_init(struct ast_private *ast);
 
 #define AST_MM_ALIGN_SHIFT 4
 #define AST_MM_ALIGN_MASK ((1 << AST_MM_ALIGN_SHIFT) - 1)
drivers/gpu/drm/ast/ast_main.c +1 -34
index 2642e6d0152b..860a43a64b31 100644
@@ -31,7 +31,6 @@
 #include <drm/drm_atomic_helper.h>
 #include <drm/drm_crtc_helper.h>
 #include <drm/drm_gem.h>
-#include <drm/drm_gem_framebuffer_helper.h>
 #include <drm/drm_gem_vram_helper.h>
 
 #include "ast_drv.h"
@@ -379,13 +378,6 @@ static int ast_get_dram_info(struct drm_device *dev)
 	return 0;
 }
 
-static const struct drm_mode_config_funcs ast_mode_funcs = {
-	.fb_create = drm_gem_fb_create,
-	.mode_valid = drm_vram_helper_mode_valid,
-	.atomic_check = drm_atomic_helper_check,
-	.atomic_commit = drm_atomic_helper_commit,
-};
-
 static u32 ast_get_vram_info(struct drm_device *dev)
 {
 	struct ast_private *ast = to_ast_private(dev);
@@ -473,35 +465,10 @@ int ast_driver_load(struct drm_device *dev, unsigned long flags)
 	if (ret)
 		goto out_free;
 
-	ret = drmm_mode_config_init(dev);
-	if (ret)
-		goto out_free;
-
-	dev->mode_config.funcs = (void *)&ast_mode_funcs;
-	dev->mode_config.min_width = 0;
-	dev->mode_config.min_height = 0;
-	dev->mode_config.preferred_depth = 24;
-	dev->mode_config.prefer_shadow = 1;
-	dev->mode_config.fb_base = pci_resource_start(ast->dev->pdev, 0);
-
-	if (ast->chip == AST2100 ||
-	    ast->chip == AST2200 ||
-	    ast->chip == AST2300 ||
-	    ast->chip == AST2400 ||
-	    ast->chip == AST2500) {
-		dev->mode_config.max_width = 1920;
-		dev->mode_config.max_height = 2048;
-	} else {
-		dev->mode_config.max_width = 1600;
-		dev->mode_config.max_height = 1200;
-	}
-
-	ret = ast_mode_init(dev);
+	ret = ast_mode_config_init(ast);
 	if (ret)
 		goto out_free;
 
-	drm_mode_config_reset(dev);
-
 	return 0;
 out_free:
 	kfree(ast);
drivers/gpu/drm/ast/ast_mode.c +39 -2

66 lines not on this page · raw message

Signature · 6 lines
2.27.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Acked-by on the v2 series
#18 lore raw
In reply to Thomas Zimmermann

Hi Thomas.

Quoted 19 lines · Thomas Zimmermann

This is the first patchset to convert ast to use managed interfaces. These patches address modesetting. I expect that there will be at least one more set of patches for memory management and one for device structures.

Patches 1 to 11 tackle HW cursor handling. The overall point is to get cursor support out of the plane functions and put the code into helpers. There are quite a few improvements that make cursors easier and faster to use. Patch 10 converts cursors to managed release.

With cursors out of the way, modesetting initialization is much more simple. Patches 12 to 14 put all related code next to each other and switch to managed initialization.

The patchset was tested on AST2100 hardware.

v2:
* use to_ast_private() instead of
struct drm_device.dev_private (Sam)

Quoted 16 lines

Thomas Zimmermann (14):
drm/ast: Move cursor functions to ast_cursor.c drm/ast: Pass struct ast_private instance to cursor init/fini
functions
drm/ast: Move cursor fb pinning and mapping into helper drm/ast: Update cursor image and checksum from same function drm/ast: Move cursor pageflip into helper
drm/ast: Replace ast_cursor_move() with ast_cursor_show() drm/ast: Don't enable HW cursors twice during atomic update drm/ast: Add helper to hide cursor
drm/ast: Keep cursor HW BOs mapped
drm/ast: Managed cursor release
drm/ast: Init cursors before creating modesetting structures drm/ast: Replace struct ast_crtc with struct drm_crtc drm/ast: Use managed mode-config init
drm/ast: Initialize mode setting in ast_mode_config_init()

I have browsed the patch-set. Nothing jumped at me but then most of the bo handling I do not understand.

Feel free to add:

to all patches.

But I hope someone else that knows this better could jump in and take a look too.

Sam

Quoted 9 lines
 drivers/gpu/drm/ast/Makefile     |   3 +-
 drivers/gpu/drm/ast/ast_cursor.c | 289 +++++++++++++++++++++++++++
 drivers/gpu/drm/ast/ast_drv.h    |  19 +-
 drivers/gpu/drm/ast/ast_main.c   |  35 +---
 drivers/gpu/drm/ast/ast_mode.c   | 322 ++++++-------------------------
 5 files changed, 359 insertions(+), 309 deletions(-)
 create mode 100644 drivers/gpu/drm/ast/ast_cursor.c
Quoted 7 lines

--
2.27.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

author maintainer
#19 lore raw

Hi

Am 03.07.20 um 08:44 schrieb Sam Ravnborg:

Quoted 41 lines

Hi Thomas.

Quoted 19 lines · Thomas Zimmermann

This is the first patchset to convert ast to use managed interfaces. These patches address modesetting. I expect that there will be at least one more set of patches for memory management and one for device structures.

Patches 1 to 11 tackle HW cursor handling. The overall point is to get cursor support out of the plane functions and put the code into helpers. There are quite a few improvements that make cursors easier and faster to use. Patch 10 converts cursors to managed release.

With cursors out of the way, modesetting initialization is much more simple. Patches 12 to 14 put all related code next to each other and switch to managed initialization.

The patchset was tested on AST2100 hardware.

v2:
* use to_ast_private() instead of
struct drm_device.dev_private (Sam)

Quoted 16 lines

Thomas Zimmermann (14):
drm/ast: Move cursor functions to ast_cursor.c drm/ast: Pass struct ast_private instance to cursor init/fini
functions
drm/ast: Move cursor fb pinning and mapping into helper drm/ast: Update cursor image and checksum from same function drm/ast: Move cursor pageflip into helper
drm/ast: Replace ast_cursor_move() with ast_cursor_show() drm/ast: Don't enable HW cursors twice during atomic update drm/ast: Add helper to hide cursor
drm/ast: Keep cursor HW BOs mapped
drm/ast: Managed cursor release
drm/ast: Init cursors before creating modesetting structures drm/ast: Replace struct ast_crtc with struct drm_crtc drm/ast: Use managed mode-config init
drm/ast: Initialize mode setting in ast_mode_config_init()

I have browsed the patch-set. Nothing jumped at me but then most of the bo handling I do not understand.

Quoted 6 lines

Feel free to add:

to all patches.

But I hope someone else that knows this better could jump in and take a look too.

Thank you so much. Finding reviewers for such obscure drivers is not easy. I appreciate your feedback.

Best regards
Thomas

Quoted 24 lines

Sam

Quoted 9 lines
 drivers/gpu/drm/ast/Makefile     |   3 +-
 drivers/gpu/drm/ast/ast_cursor.c | 289 +++++++++++++++++++++++++++
 drivers/gpu/drm/ast/ast_drv.h    |  19 +-
 drivers/gpu/drm/ast/ast_main.c   |  35 +---
 drivers/gpu/drm/ast/ast_mode.c   | 322 ++++++-------------------------
 5 files changed, 359 insertions(+), 309 deletions(-)
 create mode 100644 drivers/gpu/drm/ast/ast_cursor.c
Quoted 7 lines

--
2.27.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Signature · 6 lines
Thomas Zimmermann
Graphics Driver Developer
SUSE Software Solutions Germany GmbH
Maxfeldstr. 5, 90409 Nürnberg, Germany
(HRB 36809, AG Nürnberg)
Geschäftsführer: Felix Imendörffer

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel