Add support for PinePhone LCD panel
Subsystems (6)
v7 cover Add support for PinePhone LCD panel
This patchset adds support for the LCD panel of PinePhone.
I've tested this on PinePhone 1.0 and 1.2.
Please take a look.
thank you and regards,
Ondrej Jirman
Changes in v7:
- Removed mode.vrefresh, rebased onto next-20200701
- v6->v7 diff: https://megous.com/dl/tmp/v6-v7.patch
Changes in v6:
- Fixed spacing in yaml
- Fixed wrong vccio->iovcc supply name in the bindings doc
- I noticed that the original driver uses a delay of 20ms in the init function to achieve a combined total of 120ms required from post-reset to display_on. I've added a similar delay to xbd599_init, so that xbd599 panel also has the right timing. (patch 9)
- v5->v6 diff: https://megous.com/dl/tmp/v5-v6.patch
- Added review/ack tags
- Learned to run dt_binding_check by myself ;)
Changes in v5:
- rewritten on top of rocktech-jh057n00900 driver
- rocktech-jh057n00900 renamed to st7703 (controller name)
- converted rocktech-jh057n00900 bindings to yaml and extended for xbd599
Changes in v4:
- use ->type from the mode instead of hardcoding (Samuel)
- move init_sequence to ->prepare (Samuel)
- move anti-flicker delay to ->enable, explain it (Samuel)
- add enter_sleep after display_off (Samuel)
- drop ->disable (move code to ->unprepare)
- add ID bytes dumping (Linus)
(I can't test it since allwinner DSI driver has a broken
dcs_read function, and I didn't manage to fix it.)
- document magic bytes (Linus)
- assert reset during powerup
- cleanup powerup timings according to the datasheet
Changes in v3:
- Panel driver renamed to the name of the LCD controller
- Re-organize the driver slightly to more easily support more panels based on the same controller.
- Add patch to enable the touchscreen to complete the LCD support on PinePhone.
- Dropped the "DSI fix" patch (the driver seems to work for me without it)
- Improved brightness levels handling:
- PinePhone 1.0 uses default levels generated by the driver
- On PinePhone 1.1 duty cycles < 20% lead to black screen, so default levels can't be used. Martijn Braam came up with a list of duty cycle values that lead to perception of linear brigtness level <-> light intensity on PinePhone 1.1
- There was some feedback on v2 about this being similar to st7701. It's only similar in name. Most of the "user commands" are different, so I opted to keep this in a new driver instead of creating st770x.
Anyone who likes to check the differences, here are datasheets:
- https://megous.com/dl/tmp/ST7703_DS_v01_20160128.pdf
- https://megous.com/dl/tmp/ST7701.pdf
Changes in v2:
- DT Example fix.
- DT Format fix.
- Raised copyright info to 2020.
- Sort panel operation functions.
- Sort inclusion.
-- For phone owners: --
There's an open question on how to set the backlight brightness values on post 1.0 revision phone, since lower duty cycles (< 10-20%) lead to backlight being black. It would be nice if more people can test the various backlight levels on 1.1 and 1.2 revision with this change in dts:
brightness-levels = <0 1000>;
num-interpolated-steps = <1000>;and report at what brightness level the backlight turns on. So far it seems this has a wide range. Lowest useable duty cycle for me is ~7% on 1.2 and for Martijn ~20% on 1.1.
Icenowy Zheng (2):
dt-bindings: vendor-prefixes: Add Xingbangda
arm64: dts: sun50i-a64-pinephone: Enable LCD support on PinePhone
Ondrej Jirman (11):
dt-bindings: panel: Convert rocktech,jh057n00900 to yaml
dt-bindings: panel: Add compatible for Xingbangda XBD599 panel drm/panel: rocktech-jh057n00900: Rename the driver to st7703 drm/panel: st7703: Rename functions from jh057n prefix to st7703 drm/panel: st7703: Prepare for supporting multiple panels drm/panel: st7703: Move code specific to jh057n closer together drm/panel: st7703: Move generic part of init sequence to enable
callback
drm/panel: st7703: Add support for Xingbangda XBD599 drm/panel: st7703: Enter sleep after display off drm/panel: st7703: Assert reset prior to powering down the regulators
arm64: dts: sun50i-a64-pinephone: Add touchscreen support
.../display/panel/rocktech,jh057n00900.txt | 23 - .../display/panel/rocktech,jh057n00900.yaml | 70 ++ .../devicetree/bindings/vendor-prefixes.yaml | 2 + .../allwinner/sun50i-a64-pinephone-1.1.dts | 19 + .../dts/allwinner/sun50i-a64-pinephone.dtsi | 54 ++ drivers/gpu/drm/panel/Kconfig | 26 +- drivers/gpu/drm/panel/Makefile | 2 +- .../drm/panel/panel-rocktech-jh057n00900.c | 423 ----------- drivers/gpu/drm/panel/panel-sitronix-st7703.c | 654 ++++++++++++++++++ 9 files changed, 813 insertions(+), 460 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.txt create mode 100644 Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.yaml delete mode 100644 drivers/gpu/drm/panel/panel-rocktech-jh057n00900.c create mode 100644 drivers/gpu/drm/panel/panel-sitronix-st7703.c
Signature · 1 line
2.27.0
PATCH v7 1/13 dt-bindings: vendor-prefixes: Add Xingbangda
From: Icenowy Zheng <[email protected]>
Shenzhen Xingbangda Display Technology Co., Ltd is a company which produces LCD modules. It supplies the LCD panels for the PinePhone.
Add the vendor prefix of it.
--- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/vendor-prefixes.yaml +2 -0
@@ -1157,6 +1157,8 @@ patternProperties: description: Xiaomi Technology Co., Ltd. "^xillybus,.*": description: Xillybus Ltd. + "^xingbangda,.*": + description: Shenzhen Xingbangda Display Technology Co., Ltd "^xinpeng,.*": description: Shenzhen Xinpeng Technology Co., Ltd "^xlnx,.*":
Signature · 1 line
2.27.0
PATCH v7 2/13 dt-bindings: panel: Convert rocktech,jh057n00900 to yaml
In reply to Ondrej JirmanConvert Rocktech MIPI DSI panel driver from txt to yaml bindings.
--- .../display/panel/rocktech,jh057n00900.txt | 23 ------- .../display/panel/rocktech,jh057n00900.yaml | 66 +++++++++++++++++++ 2 files changed, 66 insertions(+), 23 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.txt create mode 100644 Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.yaml
Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.txt deleted +0 -23
@@ -1,23 +0,0 @@ -Rocktech jh057n00900 5.5" 720x1440 TFT LCD panel - -Required properties: -- compatible: should be "rocktech,jh057n00900" -- reg: DSI virtual channel of the peripheral -- reset-gpios: panel reset gpio -- backlight: phandle of the backlight device attached to the panel -- vcc-supply: phandle of the regulator that provides the vcc supply voltage. -- iovcc-supply: phandle of the regulator that provides the iovcc supply - voltage. - -Example: - - &mipi_dsi { - panel@0 { - compatible = "rocktech,jh057n00900"; - reg = <0>; - backlight = <&backlight>; - reset-gpios = <&gpio3 13 GPIO_ACTIVE_LOW>; - vcc-supply = <®_2v8_p>; - iovcc-supply = <®_1v8_p>; - }; - };
Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.yaml new file +66 -0
66 lines not on this page · raw message
Signature · 1 line
2.27.0
Rob Herring
maintainerRe: [PATCH v7 02/13] dt-bindings: panel: Convert rocktech, jh057n00900 to yaml
Quoted 10 lines · Ondrej Jirman
Convert Rocktech MIPI DSI panel driver from txt to yaml bindings.
Signed-off-by Ondrej Jirman <[email protected]>--- .../display/panel/rocktech,jh057n00900.txt | 23 ------- .../display/panel/rocktech,jh057n00900.yaml | 66 +++++++++++++++++++ 2 files changed, 66 insertions(+), 23 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.txt create mode 100644 Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.yaml
My bot found errors running 'make dt_binding_check' on your patch:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/nwl-dsi.example.dt.yaml: panel@0: '#address-cells', '#size-cells', 'port@0' do not match any of the regexes: 'pinctrl-[0-9]+' /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/nwl-dsi.example.dt.yaml: panel@0: 'vcc-supply' is a required property /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/nwl-dsi.example.dt.yaml: panel@0: 'iovcc-supply' is a required property /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/nwl-dsi.example.dt.yaml: panel@0: 'reset-gpios' is a required property
See https://patchwork.ozlabs.org/patch/1320690
If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure dt-schema is up to date:
pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
Please check and re-submit.
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v7 02/13] dt-bindings: panel: Convert rocktech, jh057n00900 to yaml
Quoted 13 lines · Rob Herring
Quoted 10 lines · Ondrej Jirman
Convert Rocktech MIPI DSI panel driver from txt to yaml bindings.
Signed-off-by Ondrej Jirman <[email protected]>--- .../display/panel/rocktech,jh057n00900.txt | 23 ------- .../display/panel/rocktech,jh057n00900.yaml | 66 +++++++++++++++++++ 2 files changed, 66 insertions(+), 23 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.txt create mode 100644 Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.yaml
Quoted 6 lines
My bot found errors running 'make
dt_binding_check' on your patch:/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/nwl-dsi.example.dt.yaml: panel@0: '#address-cells', '#size-cells', 'port@0' do not match any of the regexes: 'pinctrl-[0-9]+' /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/nwl-dsi.example.dt.yaml: panel@0: 'vcc-supply' is a required property /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/nwl-dsi.example.dt.yaml: panel@0: 'iovcc-supply' is a required property /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/nwl-dsi.example.dt.yaml: panel@0: 'reset-gpios' is a required property
Paths look bogus ^^^^
It should be .../rocktech,jh057n00900.yaml: ...
regards,
o.
Quoted 10 lines
See https://patchwork.ozlabs.org/patch/1320690
If you already ran 'make
dt_binding_check' and didn't see the above error(s), then make sure dt-schema is up to date:pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
Please check and re-submit.
Re: [PATCH v7 02/13] dt-bindings: panel: Convert rocktech, jh057n00900 to yaml
Hi Ondrej.
Quoted 10 lines
Quoted 6 lines
My bot found errors running 'make
dt_binding_check' on your patch:/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/nwl-dsi.example.dt.yaml: panel@0: '#address-cells', '#size-cells', 'port@0' do not match any of the regexes: 'pinctrl-[0-9]+' /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/nwl-dsi.example.dt.yaml: panel@0: 'vcc-supply' is a required property /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/nwl-dsi.example.dt.yaml: panel@0: 'iovcc-supply' is a required property /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/nwl-dsi.example.dt.yaml: panel@0: 'reset-gpios' is a required property
Paths look bogus ^^^^
It should be
.../rocktech,jh057n00900.yaml: ...
The example in nwl-dsi.yaml contains:
compatible = "rocktech,jh057n00900";
So the example is checked against your updated binding. And the binding check fails because the example is no longer valid.
This needs to be fixed as we do not wat to introduce new errors. Either the example or the binding needs the fix.
Sam
Quoted 14 lines
regards,
o.Quoted 10 lines
See https://patchwork.ozlabs.org/patch/1320690
If you already ran 'make
dt_binding_check' and didn't see the above error(s), then make sure dt-schema is up to date:pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
Please check and re-submit.
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v7 02/13] dt-bindings: panel: Convert rocktech, jh057n00900 to yaml
Hello Sam,
Quoted 11 lines · Sam Ravnborg
Hi Ondrej.
Quoted 9 lines
Quoted 6 lines
My bot found errors running 'make
dt_binding_check' on your patch:/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/nwl-dsi.example.dt.yaml: panel@0: '#address-cells', '#size-cells', 'port@0' do not match any of the regexes: 'pinctrl-[0-9]+' /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/nwl-dsi.example.dt.yaml: panel@0: 'vcc-supply' is a required property /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/nwl-dsi.example.dt.yaml: panel@0: 'iovcc-supply' is a required property /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/nwl-dsi.example.dt.yaml: panel@0: 'reset-gpios' is a required property
Paths look bogus ^^^^
Quoted 7 lines
Quoted 1 line
It should be
.../rocktech,jh057n00900.yaml: ...The example in
nwl-dsi.yamlcontains:compatible = "rocktech,jh057n00900";So the example is checked against your updated binding. And the binding check fails because the example is no longer valid.
Ah, now I understand.
Quoted 2 lines
This needs to be fixed as we do not wat to introduce new errors. Either the example or the binding needs the fix.
I think we can unrequire the supplies, but reset is needed really.
The panel only has one port, so there should be no address/size-cells in the example, and port@0 should be just port to match existing binding. If it had multiple ports, port@0 would have to be inside ports { } node anyway, according to the existing binding. Then add reset-gpios to the example...
And that should fix it.
I'll prepare the patch shortly.
regards,
o.
Quoted 17 lines
Sam
Quoted 14 lines
regards,
o.Quoted 10 lines
See https://patchwork.ozlabs.org/patch/1320690
If you already ran 'make
dt_binding_check' and didn't see the above error(s), then make sure dt-schema is up to date:pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
Please check and re-submit.
Re: [PATCH v7 02/13] dt-bindings: panel: Convert rocktech, jh057n00900 to yaml
Quoted 22 lines · megous hlavni
Hello Sam,
Quoted 11 lines · Sam Ravnborg
Hi Ondrej.
Quoted 9 lines
Quoted 6 lines
My bot found errors running 'make
dt_binding_check' on your patch:/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/nwl-dsi.example.dt.yaml: panel@0: '#address-cells', '#size-cells', 'port@0' do not match any of the regexes: 'pinctrl-[0-9]+' /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/nwl-dsi.example.dt.yaml: panel@0: 'vcc-supply' is a required property /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/nwl-dsi.example.dt.yaml: panel@0: 'iovcc-supply' is a required property /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/nwl-dsi.example.dt.yaml: panel@0: 'reset-gpios' is a required property
Paths look bogus ^^^^
Quoted 7 lines
Quoted 1 line
It should be
.../rocktech,jh057n00900.yaml: ...The example in
nwl-dsi.yamlcontains:compatible = "rocktech,jh057n00900";So the example is checked against your updated binding. And the binding check fails because the example is no longer valid.
Quoted 6 lines
Ah, now I understand.
Quoted 2 lines
This needs to be fixed as we do not wat to introduce new errors. Either the example or the binding needs the fix.
I think we can unrequire the supplies, but reset is needed really.
Hmm, that's probably wrong kind of thinking. Panel has the supplies, and obviously requires them, so the dts must describe them somehow, even if they are the fixed supplies. So I'll not unrequire them.
Quoted 30 lines
The panel only has one port, so there should be no address/size-cells in the example, and port@0 should be just port to match existing binding. If it had multiple ports, port@0 would have to be inside ports { } node anyway, according to the existing binding. Then add reset-gpios to the example...
And that should fix it.
I'll prepare the patch shortly.
regards,
o.Quoted 17 lines
Sam
Quoted 14 lines
regards,
o.Quoted 10 lines
See https://patchwork.ozlabs.org/patch/1320690
If you already ran 'make
dt_binding_check' and didn't see the above error(s), then make sure dt-schema is up to date:pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
Please check and re-submit.
PATCH v7 3/13 dt-bindings: panel: Add compatible for Xingbangda XBD599 panel
In reply to Ondrej JirmanXingbangda XBD599 is a 5.99" 720x1440 MIPI-DSI LCD panel. It is based on Sitronix ST7703 LCD controller just like rocktech,jh057n00900. It is used in PinePhone.
Add a compatible for it.
--- .../bindings/display/panel/rocktech,jh057n00900.yaml | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.yaml +5 -1
@@ -18,7 +18,11 @@ allOf: properties: compatible: - const: rocktech,jh057n00900 + enum: + # Rocktech JH057N00900 5.5" 720x1440 TFT LCD panel + - rocktech,jh057n00900 + # Xingbangda XBD599 5.99" 720x1440 TFT LCD panel + - xingbangda,xbd599 reg: maxItems: 1
Signature · 1 line
2.27.0
PATCH v7 4/13 drm/panel: rocktech-jh057n00900: Rename the driver to st7703
In reply to Ondrej JirmanThis rename is done so that the driver matches the name of the display controller and in preparation for adding support for more panels to the driver.
This is just a basic file rename, with no code changes.
---
drivers/gpu/drm/panel/Kconfig | 26 +++++++++----------
drivers/gpu/drm/panel/Makefile | 2 +-
...-jh057n00900.c => panel-sitronix-st7703.c} | 0
3 files changed, 14 insertions(+), 14 deletions(-)
rename drivers/gpu/drm/panel/{panel-rocktech-jh057n00900.c => panel-sitronix-st7703.c} (100%)drivers/gpu/drm/panel/Kconfig +13 -13
@@ -283,19 +283,6 @@ config DRM_PANEL_RAYDIUM_RM68200 Say Y here if you want to enable support for Raydium RM68200 720x1280 DSI video mode panel. -config DRM_PANEL_ROCKTECH_JH057N00900 - tristate "Rocktech JH057N00900 MIPI touchscreen panel" - depends on OF - depends on DRM_MIPI_DSI - depends on BACKLIGHT_CLASS_DEVICE - help - Say Y here if you want to enable support for Rocktech JH057N00900 - MIPI DSI panel as e.g. used in the Librem 5 devkit. It has a - resolution of 720x1440 pixels, a built in backlight and touch - controller. - Touch input support is provided by the goodix driver and needs to be - selected separately. - config DRM_PANEL_RONBO_RB070D30 tristate "Ronbo Electronics RB070D30 panel" depends on OF
@@ -395,6 +382,19 @@ config DRM_PANEL_SITRONIX_ST7701 ST7701 controller for 480X864 LCD panels with MIPI/RGB/SPI system interfaces. +config DRM_PANEL_SITRONIX_ST7703 + tristate "Sitronix ST7703 based MIPI touchscreen panels" + depends on OF + depends on DRM_MIPI_DSI + depends on BACKLIGHT_CLASS_DEVICE + help + Say Y here if you want to enable support for Sitronix ST7703 based + panels, souch as Rocktech JH057N00900 MIPI DSI panel as e.g. used in + the Librem 5 devkit. It has a resolution of 720x1440 pixels, a built + in backlight and touch controller. + Touch input support is provided by the goodix driver and needs to be + selected separately. + config DRM_PANEL_SITRONIX_ST7789V tristate "Sitronix ST7789V panel" depends on OF && SPI
drivers/gpu/drm/panel/Makefile +1 -1
@@ -27,7 +27,6 @@ obj-$(CONFIG_DRM_PANEL_PANASONIC_VVX10F034N00) += panel-panasonic-vvx10f034n00.o obj-$(CONFIG_DRM_PANEL_RASPBERRYPI_TOUCHSCREEN) += panel-raspberrypi-touchscreen.o obj-$(CONFIG_DRM_PANEL_RAYDIUM_RM67191) += panel-raydium-rm67191.o obj-$(CONFIG_DRM_PANEL_RAYDIUM_RM68200) += panel-raydium-rm68200.o -obj-$(CONFIG_DRM_PANEL_ROCKTECH_JH057N00900) += panel-rocktech-jh057n00900.o obj-$(CONFIG_DRM_PANEL_RONBO_RB070D30) += panel-ronbo-rb070d30.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_LD9040) += panel-samsung-ld9040.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6D16D0) += panel-samsung-s6d16d0.o
@@ -41,6 +40,7 @@ obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o obj-$(CONFIG_DRM_PANEL_SHARP_LS037V7DW01) += panel-sharp-ls037v7dw01.o obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7701) += panel-sitronix-st7701.o +obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7703) += panel-sitronix-st7703.o obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o obj-$(CONFIG_DRM_PANEL_SONY_ACX424AKP) += panel-sony-acx424akp.o obj-$(CONFIG_DRM_PANEL_SONY_ACX565AKM) += panel-sony-acx565akm.o
drivers/gpu/drm/panel/panel-sitronix-st7703.c renamed from drivers/gpu/drm/panel/panel-rocktech-jh057n00900.c +0 -0
Signature · 1 line
2.27.0
PATCH v7 5/13 drm/panel: st7703: Rename functions from jh057n prefix to st7703
In reply to Ondrej JirmanThis is done so that code that's not specific to a particular jh057n panel is named after the controller. Functions specific to the panel are kept named after the panel.
--- drivers/gpu/drm/panel/panel-sitronix-st7703.c | 90 ++++++++++--------- 1 file changed, 46 insertions(+), 44 deletions(-)
drivers/gpu/drm/panel/panel-sitronix-st7703.c +46 -44
@@ -1,6 +1,8 @@// SPDX-License-Identifier: GPL-2.0 /* -* Rockteck jh057n00900 5.5" MIPI-DSI panel driver +* Driver for panels based on Sitronix ST7703 controller, souch as: +* +* - Rocktech jh057n00900 5.5" MIPI-DSI panel * * Copyright (C) Purism SPC 2019 */
@@ -21,7 +23,7 @@#include <drm/drm_panel.h> #include <drm/drm_print.h> -#define DRV_NAME "panel-rocktech-jh057n00900" +#define DRV_NAME "panel-sitronix-st7703"/* Manufacturer specific Commands send via DSI */ #define ST7703_CMD_ALL_PIXEL_OFF 0x22
@@ -45,7 +47,7 @@#define ST7703_CMD_SETGIP1 0xE9#define ST7703_CMD_SETGIP2 0xEA -struct jh057n { +struct st7703 {struct device *dev;struct drm_panel panel;struct gpio_desc *reset_gpio;
@@ -56,9 +58,9 @@ struct jh057n {struct dentry *debugfs; }; -static inline struct jh057n *panel_to_jh057n (struct drm_panel *panel) +static inline struct st7703 *panel_to_st7703 (struct drm_panel *panel) { - return container_of(panel, struct jh057n, panel); + return container_of(panel, struct st7703, panel); } #define dsi_generic_write_seq(dsi, seq...) do { \
@@ -69,7 +71,7 @@ static inline struct jh057n *panel_to_jh057n(struct drm_panel *panel)return ret; \ }while (0 ) -static int jh057n_init_sequence(struct jh057n *ctx) +static int jh057n_init_sequence(struct st7703 *ctx) {struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev);struct device *dev = ctx->dev;
@@ -141,9 +143,9 @@ static int jh057n_init_sequence(struct jh057n *ctx)return 0 ; } -static int jh057n_enable (struct drm_panel *panel) +static int st7703_enable (struct drm_panel *panel) { -struct jh057n *ctx =panel_to_jh057n (panel); +struct st7703 *ctx =panel_to_st7703 (panel);int ret; ret =jh057n_init_sequence (ctx);
@@ -156,17 +158,17 @@ static int jh057n_enable(struct drm_panel *panel)return 0 ; } -static int jh057n_disable (struct drm_panel *panel) +static int st7703_disable (struct drm_panel *panel) { -struct jh057n *ctx =panel_to_jh057n (panel); +struct st7703 *ctx =panel_to_st7703 (panel);struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev);return mipi_dsi_dcs_set_display_off (dsi); } -static int jh057n_unprepare (struct drm_panel *panel) +static int st7703_unprepare (struct drm_panel *panel) { -struct jh057n *ctx =panel_to_jh057n (panel); +struct st7703 *ctx =panel_to_st7703 (panel);if (!ctx->prepared)return 0 ;
@@ -178,9 +180,9 @@ static int jh057n_unprepare(struct drm_panel *panel)return 0 ; } -static int jh057n_prepare (struct drm_panel *panel) +static int st7703_prepare (struct drm_panel *panel) { -struct jh057n *ctx =panel_to_jh057n (panel); +struct st7703 *ctx =panel_to_st7703 (panel);int ret;if (ctx->prepared)
@@ -229,10 +231,10 @@ static const struct drm_display_mode default_mode = { .height_mm = 130, }; -static int jh057n_get_modes (struct drm_panel *panel, +static int st7703_get_modes (struct drm_panel *panel,struct drm_connector *connector) { -struct jh057n *ctx =panel_to_jh057n (panel); +struct st7703 *ctx =panel_to_st7703 (panel);struct drm_display_mode *mode; mode =drm_mode_duplicate (connector->dev, &default_mode);
@@ -253,17 +255,17 @@ static int jh057n_get_modes(struct drm_panel *panel,return 1 ; } -static const struct drm_panel_funcs jh057n_drm_funcs = { - .disable = jh057n_disable, - .unprepare = jh057n_unprepare, - .prepare = jh057n_prepare, - .enable = jh057n_enable, - .get_modes = jh057n_get_modes, +static const struct drm_panel_funcs st7703_drm_funcs = { + .disable = st7703_disable, + .unprepare = st7703_unprepare, + .prepare = st7703_prepare, + .enable = st7703_enable, + .get_modes = st7703_get_modes, };static int allpixelson_set (void *data,u64 val) { -struct jh057n *ctx = data; +struct st7703 *ctx = data;struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev);DRM_DEV_DEBUG_DRIVER (ctx->dev,"Setting all pixels on\n" );
@@ -281,7 +283,7 @@ static int allpixelson_set(void *data, u64 val)DEFINE_SIMPLE_ATTRIBUTE (allpixelson_fops,NULL , allpixelson_set,"%llu\n" ); -static void jh057n_debugfs_init (struct jh057n *ctx) +static void st7703_debugfs_init (struct st7703 *ctx) { ctx->debugfs =debugfs_create_dir (DRV_NAME ,NULL );
@@ -289,16 +291,16 @@ static void jh057n_debugfs_init(struct jh057n *ctx) &allpixelson_fops); } -static void jh057n_debugfs_remove (struct jh057n *ctx) +static void st7703_debugfs_remove (struct st7703 *ctx) {debugfs_remove_recursive (ctx->debugfs); ctx->debugfs =NULL ; } -static int jh057n_probe (struct mipi_dsi_device *dsi) +static int st7703_probe (struct mipi_dsi_device *dsi) {struct device *dev = &dsi->dev; -struct jh057n *ctx; +struct st7703 *ctx;int ret; ctx =devm_kzalloc (dev,sizeof (*ctx),GFP_KERNEL );
@@ -339,7 +341,7 @@ static int jh057n_probe(struct mipi_dsi_device *dsi)return ret; } -drm_panel_init (&ctx->panel, dev, &jh057n_drm_funcs, +drm_panel_init (&ctx->panel, dev, &st7703_drm_funcs,DRM_MODE_CONNECTOR_DSI ); ret =drm_panel_of_backlight (&ctx->panel);
@@ -362,13 +364,13 @@ static int jh057n_probe(struct mipi_dsi_device *dsi)drm_mode_vrefresh (&default_mode), mipi_dsi_pixel_format_to_bpp(dsi->format), dsi->lanes); -jh057n_debugfs_init (ctx); +st7703_debugfs_init (ctx);return 0 ; } -static void jh057n_shutdown (struct mipi_dsi_device *dsi) +static void st7703_shutdown (struct mipi_dsi_device *dsi) { -struct jh057n *ctx =mipi_dsi_get_drvdata (dsi); +struct st7703 *ctx =mipi_dsi_get_drvdata (dsi);int ret; ret =drm_panel_unprepare (&ctx->panel);
@@ -382,12 +384,12 @@ static void jh057n_shutdown(struct mipi_dsi_device *dsi) ret); } -static int jh057n_remove (struct mipi_dsi_device *dsi) +static int st7703_remove (struct mipi_dsi_device *dsi) { -struct jh057n *ctx =mipi_dsi_get_drvdata (dsi); +struct st7703 *ctx =mipi_dsi_get_drvdata (dsi);int ret; -jh057n_shutdown (dsi); +st7703_shutdown (dsi); ret =mipi_dsi_detach (dsi);if (ret <0 )
@@ -396,28 +398,28 @@ static int jh057n_remove(struct mipi_dsi_device *dsi)drm_panel_remove (&ctx->panel); -jh057n_debugfs_remove (ctx); +st7703_debugfs_remove (ctx);return 0 ; } -static const struct of_device_id jh057n_of_match[] = { +static const struct of_device_id st7703_of_match[] = { { .compatible ="rocktech,jh057n00900" }, {/* sentinel */ } }; -MODULE_DEVICE_TABLE (of, jh057n_of_match); +MODULE_DEVICE_TABLE (of, st7703_of_match); -static struct mipi_dsi_driver jh057n_driver = { - .probe = jh057n_probe, - .remove = jh057n_remove, - .shutdown = jh057n_shutdown, +static struct mipi_dsi_driver st7703_driver = { + .probe = st7703_probe, + .remove = st7703_remove, + .shutdown = st7703_shutdown, .driver = { .name =DRV_NAME , - .of_match_table = jh057n_of_match, + .of_match_table = st7703_of_match, }, }; -module_mipi_dsi_driver (jh057n_driver); +module_mipi_dsi_driver (st7703_driver);MODULE_AUTHOR ("Guido Günther <[email protected]>" ); -MODULE_DESCRIPTION ("DRM driver for Rocktech JH057N00900 MIPI DSI panel" ); +MODULE_DESCRIPTION ("DRM driver for Sitronix ST7703 based MIPI DSI panels" );MODULE_LICENSE ("GPL v2" );
Signature · 1 line
2.27.0
PATCH v7 6/13 drm/panel: st7703: Prepare for supporting multiple panels
In reply to Ondrej JirmanParametrize the driver so that it can support more panels based on st7703 controller.
--- drivers/gpu/drm/panel/panel-sitronix-st7703.c | 43 +++++++++++++------ 1 file changed, 31 insertions(+), 12 deletions(-)
drivers/gpu/drm/panel/panel-sitronix-st7703.c +31 -12
@@ -13,6 +13,7 @@#include <linux/media-bus-format.h> #include <linux/mod_devicetable.h> #include <linux/module.h> +#include <linux/of_device.h> #include <linux/regulator/consumer.h> #include <video/display_timing.h>
@@ -56,6 +57,15 @@ struct st7703 {bool prepared;struct dentry *debugfs; +const struct st7703_panel_desc *desc; +}; + +struct st7703_panel_desc { +const struct drm_display_mode *mode; +unsigned int lanes; +unsigned long mode_flags; +enum mipi_dsi_pixel_format format; +int (*init_sequence)(struct st7703 *ctx); };static inline struct st7703 *panel_to_st7703 (struct drm_panel *panel)
@@ -148,7 +158,7 @@ static int st7703_enable(struct drm_panel *panel)struct st7703 *ctx =panel_to_st7703 (panel);int ret; - ret =jh057n_init_sequence (ctx); + ret = ctx->desc->init_sequence (ctx);if (ret <0 ) {DRM_DEV_ERROR (ctx->dev,"Panel init sequence failed: %d\n" , ret);
@@ -216,7 +226,7 @@ static int st7703_prepare(struct drm_panel *panel)return ret; } -static const struct drm_display_mode default_mode = { +static const struct drm_display_mode jh057n00900_mode = { .hdisplay =720 , .hsync_start =720 +90 , .hsync_end =720 +90 +20 ,
@@ -231,17 +241,26 @@ static const struct drm_display_mode default_mode = { .height_mm = 130, }; +struct st7703_panel_desc jh057n00900_panel_desc = { + .mode = &jh057n00900_mode, + .lanes =4 , + .mode_flags =MIPI_DSI_MODE_VIDEO | +MIPI_DSI_MODE_VIDEO_BURST |MIPI_DSI_MODE_VIDEO_SYNC_PULSE , + .format =MIPI_DSI_FMT_RGB888 , + .init_sequence = jh057n_init_sequence, +}; +static int st7703_get_modes (struct drm_panel *panel,struct drm_connector *connector) {struct st7703 *ctx =panel_to_st7703 (panel);struct drm_display_mode *mode; - mode =drm_mode_duplicate (connector->dev, &default_mode); + mode =drm_mode_duplicate (connector->dev, ctx->desc->mode);if (!mode) {DRM_DEV_ERROR (ctx->dev,"Failed to add mode %ux%u@%u\n" , - default_mode.hdisplay, default_mode.vdisplay, -drm_mode_vrefresh (&default_mode)); + ctx->desc->mode->hdisplay, ctx->desc->mode->vdisplay, +drm_mode_vrefresh (ctx->desc->mode));return -ENOMEM ; }
@@ -316,11 +335,11 @@ static int st7703_probe(struct mipi_dsi_device *dsi)mipi_dsi_set_drvdata (dsi, ctx); ctx->dev = dev; + ctx->desc =of_device_get_match_data (dev); - dsi->lanes =4 ; - dsi->format =MIPI_DSI_FMT_RGB888 ; - dsi->mode_flags =MIPI_DSI_MODE_VIDEO | -MIPI_DSI_MODE_VIDEO_BURST |MIPI_DSI_MODE_VIDEO_SYNC_PULSE ; + dsi->mode_flags = ctx->desc->mode_flags; + dsi->format = ctx->desc->format; + dsi->lanes = ctx->desc->lanes; ctx->vcc =devm_regulator_get (dev,"vcc" );if (IS_ERR (ctx->vcc)) {
@@ -360,8 +379,8 @@ static int st7703_probe(struct mipi_dsi_device *dsi) }DRM_DEV_INFO (dev,"%ux%u@%u %ubpp dsi %udl - ready\n" , - default_mode.hdisplay, default_mode.vdisplay, -drm_mode_vrefresh (&default_mode), + ctx->desc->mode->hdisplay, ctx->desc->mode->vdisplay, +drm_mode_vrefresh (ctx->desc->mode),mipi_dsi_pixel_format_to_bpp (dsi->format), dsi->lanes);st7703_debugfs_init (ctx);
@@ -404,7 +423,7 @@ static int st7703_remove(struct mipi_dsi_device *dsi) }static const struct of_device_id st7703_of_match[] = { - { .compatible ="rocktech,jh057n00900" }, + { .compatible ="rocktech,jh057n00900" , .data = &jh057n00900_panel_desc }, {/* sentinel */ } };MODULE_DEVICE_TABLE (of, st7703_of_match);
Signature · 1 line
2.27.0
PATCH v7 7/13 drm/panel: st7703: Move code specific to jh057n closer together
In reply to Ondrej JirmanIt's better than having it spread around the driver.
--- drivers/gpu/drm/panel/panel-sitronix-st7703.c | 48 +++++++++---------- 1 file changed, 24 insertions(+), 24 deletions(-)
drivers/gpu/drm/panel/panel-sitronix-st7703.c +24 -24
@@ -153,6 +153,30 @@ static int jh057n_init_sequence(struct st7703 *ctx)return 0 ; } +static const struct drm_display_mode jh057n00900_mode = { + .hdisplay =720 , + .hsync_start =720 +90 , + .hsync_end =720 +90 +20 , + .htotal =720 +90 +20 +20 , + .vdisplay =1440 , + .vsync_start =1440 +20 , + .vsync_end =1440 +20 +4 , + .vtotal =1440 +20 +4 +12 , + .clock =75276 , + .flags =DRM_MODE_FLAG_NHSYNC |DRM_MODE_FLAG_NVSYNC , + .width_mm =65 , + .height_mm =130 , +}; + +struct st7703_panel_desc jh057n00900_panel_desc = { + .mode = &jh057n00900_mode, + .lanes =4 , + .mode_flags =MIPI_DSI_MODE_VIDEO | +MIPI_DSI_MODE_VIDEO_BURST |MIPI_DSI_MODE_VIDEO_SYNC_PULSE , + .format =MIPI_DSI_FMT_RGB888 , + .init_sequence = jh057n_init_sequence, +}; +static int st7703_enable (struct drm_panel *panel) {struct st7703 *ctx =panel_to_st7703 (panel);
@@ -226,30 +250,6 @@ static int st7703_prepare(struct drm_panel *panel)return ret; } -static const struct drm_display_mode jh057n00900_mode = { - .hdisplay =720 , - .hsync_start =720 +90 , - .hsync_end =720 +90 +20 , - .htotal =720 +90 +20 +20 , - .vdisplay =1440 , - .vsync_start =1440 +20 , - .vsync_end =1440 +20 +4 , - .vtotal =1440 +20 +4 +12 , - .clock =75276 , - .flags =DRM_MODE_FLAG_NHSYNC |DRM_MODE_FLAG_NVSYNC , - .width_mm =65 , - .height_mm =130 , -}; - -struct st7703_panel_desc jh057n00900_panel_desc = { - .mode = &jh057n00900_mode, - .lanes =4 , - .mode_flags =MIPI_DSI_MODE_VIDEO | -MIPI_DSI_MODE_VIDEO_BURST |MIPI_DSI_MODE_VIDEO_SYNC_PULSE , - .format =MIPI_DSI_FMT_RGB888 , - .init_sequence = jh057n_init_sequence, -}; -static int st7703_get_modes (struct drm_panel *panel,struct drm_connector *connector) {
Signature · 1 line
2.27.0
PATCH v7 8/13 drm/panel: st7703: Move generic part of init sequence to enable callback
In reply to Ondrej JirmanCalling sleep out and display on is a controller specific part of the initialization process. Move it out of the panel specific initialization function to the enable callback.
--- drivers/gpu/drm/panel/panel-sitronix-st7703.c | 33 ++++++++++--------- 1 file changed, 18 insertions(+), 15 deletions(-)
drivers/gpu/drm/panel/panel-sitronix-st7703.c +18 -15
@@ -84,8 +84,6 @@ static inline struct st7703 *panel_to_st7703(struct drm_panel *panel)static int jh057n_init_sequence (struct st7703 *ctx) {struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev); -struct device *dev = ctx->dev; -int ret;/* * Init sequence was supplied by the panel vendor. Most of the commands
@@ -136,20 +134,7 @@ static int jh057n_init_sequence(struct st7703 *ctx)0x18 ,0x00 ,0x09 ,0x0E ,0x29 ,0x2D ,0x3C ,0x41 ,0x37 ,0x07 ,0x0B ,0x0D ,0x10 ,0x11 ,0x0F ,0x10 , 0x11, 0x18); -msleep (20 ); - - ret =mipi_dsi_dcs_exit_sleep_mode (dsi); -if (ret <0 ) { -DRM_DEV_ERROR (dev,"Failed to exit sleep mode: %d\n" , ret); -return ret; - } -/* Panel is operational 120 msec after reset */ -msleep (60 ); - ret =mipi_dsi_dcs_set_display_on (dsi); -if (ret) -return ret; -DRM_DEV_DEBUG_DRIVER (dev,"Panel init sequence done\n" );return 0 ; }
@@ -180,6 +165,7 @@ struct st7703_panel_desc jh057n00900_panel_desc = {static int st7703_enable (struct drm_panel *panel) {struct st7703 *ctx =panel_to_st7703 (panel); +struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev);int ret; ret = ctx->desc->init_sequence (ctx);
@@ -189,6 +175,23 @@ static int st7703_enable(struct drm_panel *panel)return ret; } +msleep (20 ); + + ret =mipi_dsi_dcs_exit_sleep_mode (dsi); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev,"Failed to exit sleep mode: %d\n" , ret); +return ret; + } + +/* Panel is operational 120 msec after reset */ +msleep (60 ); + + ret =mipi_dsi_dcs_set_display_on (dsi); +if (ret) +return ret; + +DRM_DEV_DEBUG_DRIVER (ctx->dev,"Panel init sequence done\n" ); +return 0 ; }
Signature · 1 line
2.27.0
PATCH v7 9/13 drm/panel: st7703: Add support for Xingbangda XBD599
In reply to Ondrej JirmanXingbangda XBD599 is a 5.99" 720x1440 MIPI-DSI LCD panel used in PinePhone. Add support for it.
--- drivers/gpu/drm/panel/panel-sitronix-st7703.c | 199 +++++++++++++++++- 1 file changed, 197 insertions(+), 2 deletions(-)
drivers/gpu/drm/panel/panel-sitronix-st7703.c +197 -2
@@ -39,10 +39,11 @@#define ST7703_CMD_SETEXTC 0xB9#define ST7703_CMD_SETMIPI 0xBA#define ST7703_CMD_SETVDC 0xBC -#define ST7703_CMD_UNKNOWN0 0xBF +#define ST7703_CMD_UNKNOWN_BF 0xBF#define ST7703_CMD_SETSCR 0xC0#define ST7703_CMD_SETPOWER 0xC1#define ST7703_CMD_SETPANEL 0xCC +#define ST7703_CMD_UNKNOWN_C6 0xC6#define ST7703_CMD_SETGAMMA 0xE0#define ST7703_CMD_SETEQ 0xE3#define ST7703_CMD_SETGIP1 0xE9
@@ -109,7 +110,7 @@ static int jh057n_init_sequence(struct st7703 *ctx)msleep (20 );dsi_generic_write_seq (dsi,ST7703_CMD_SETVCOM ,0x3F ,0x3F ); -dsi_generic_write_seq (dsi,ST7703_CMD_UNKNOWN0 ,0x02 ,0x11 ,0x00 ); +dsi_generic_write_seq (dsi,ST7703_CMD_UNKNOWN_BF ,0x02 ,0x11 ,0x00 ); dsi_generic_write_seq(dsi, ST7703_CMD_SETGIP1, 0x82, 0x10, 0x06, 0x05, 0x9E, 0x0A, 0xA5, 0x12, 0x31, 0x23, 0x37, 0x83, 0x04, 0xBC, 0x27, 0x38,
@@ -162,6 +163,199 @@ struct st7703_panel_desc jh057n00900_panel_desc = { .init_sequence = jh057n_init_sequence, }; +#define dsi_dcs_write_seq(dsi, cmd, seq...) do { \ + static const u8 d[] = { seq }; \ + int ret; \ + ret = mipi_dsi_dcs_write(dsi, cmd, d, ARRAY_SIZE(d)); \ + if (ret < 0) \ + return ret; \ + } while (0) + + +static int xbd599_init_sequence (struct st7703 *ctx) +{ +struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev); + +/* +* Init sequence was supplied by the panel vendor. +*/ + +/* Magic sequence to unlock user commands below. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETEXTC ,0xF1 ,0x12 ,0x83 ); + +dsi_dcs_write_seq (dsi,ST7703_CMD_SETMIPI , +0x33 ,/* VC_main = 0, Lane_Number = 3 (4 lanes) */ +0x81 ,/* DSI_LDO_SEL = 1.7V, RTERM = 90 Ohm */ +0x05 ,/* IHSRX = x6 (Low High Speed driving ability) */ +0xF9 ,/* TX_CLK_SEL = fDSICLK/16 */ +0x0E ,/* HFP_OSC (min. HFP number in DSI mode) */ +0x0E ,/* HBP_OSC (min. HBP number in DSI mode) */ +/* The rest is undocumented in ST7703 datasheet */ +0x20 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 , +0x44 ,0x25 ,0x00 ,0x91 ,0x0a ,0x00 ,0x00 ,0x02 , +0x4F ,0x11 ,0x00 ,0x00 ,0x37 ); + +dsi_dcs_write_seq (dsi,ST7703_CMD_SETPOWER_EXT , +0x25 ,/* PCCS = 2, ECP_DC_DIV = 1/4 HSYNC */ +0x22 ,/* DT = 15ms XDK_ECP = x2 */ +0x20 ,/* PFM_DC_DIV = /1 */ +0x03 /* ECP_SYNC_EN = 1, VGX_SYNC_EN = 1 */ ); + +/* RGB I/F porch timing */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETRGBIF , +0x10 ,/* VBP_RGB_GEN */ +0x10 ,/* VFP_RGB_GEN */ +0x05 ,/* DE_BP_RGB_GEN */ +0x05 ,/* DE_FP_RGB_GEN */ +/* The rest is undocumented in ST7703 datasheet */ +0x03 ,0xFF , +0x00 ,0x00 , +0x00 ,0x00 ); + +/* Source driving settings. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETSCR , +0x73 ,/* N_POPON */ +0x73 ,/* N_NOPON */ +0x50 ,/* I_POPON */ +0x50 ,/* I_NOPON */ +0x00 ,/* SCR[31,24] */ +0xC0 ,/* SCR[23,16] */ +0x08 ,/* SCR[15,8] */ +0x70 ,/* SCR[7,0] */ +0x00 /* Undocumented */ ); + +/* NVDDD_SEL = -1.8V, VDDD_SEL = out of range (possibly 1.9V?) */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETVDC ,0x4E ); + +/* +* SS_PANEL = 1 (reverse scan), GS_PANEL = 0 (normal scan) +* REV_PANEL = 1 (normally black panel), BGR_PANEL = 1 (BGR) +*/ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETPANEL ,0x0B ); + +/* Zig-Zag Type C column inversion. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETCYC ,0x80 ); + +/* Set display resolution. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETDISP , +0xF0 ,/* NL = 240 */ +0x12 ,/* RES_V_LSB = 0, BLK_CON = VSSD, +* RESO_SEL = 720RGB +*/ +0xF0 /* WHITE_GND_EN = 1 (GND), +* WHITE_FRAME_SEL = 7 frames, +* ISC = 0 frames +*/ ); + +dsi_dcs_write_seq (dsi,ST7703_CMD_SETEQ , +0x00 ,/* PNOEQ */ +0x00 ,/* NNOEQ */ +0x0B ,/* PEQGND */ +0x0B ,/* NEQGND */ +0x10 ,/* PEQVCI */ +0x10 ,/* NEQVCI */ +0x00 ,/* PEQVCI1 */ +0x00 ,/* NEQVCI1 */ +0x00 ,/* reserved */ +0x00 ,/* reserved */ +0xFF ,/* reserved */ +0x00 ,/* reserved */ +0xC0 ,/* ESD_DET_DATA_WHITE = 1, ESD_WHITE_EN = 1 */ +0x10 /* SLPIN_OPTION = 1 (no need vsync after sleep-in) +* VEDIO_NO_CHECK_EN = 0 +* ESD_WHITE_GND_EN = 0 +* ESD_DET_TIME_SEL = 0 frames +*/ ); + +/* Undocumented command. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_UNKNOWN_C6 ,0x01 ,0x00 ,0xFF ,0xFF ,0x00 ); + +dsi_dcs_write_seq (dsi,ST7703_CMD_SETPOWER , +0x74 ,/* VBTHS, VBTLS: VGH = 17V, VBL = -11V */ +0x00 ,/* FBOFF_VGH = 0, FBOFF_VGL = 0 */ +0x32 ,/* VRP */ +0x32 ,/* VRN */ +0x77 ,/* reserved */ +0xF1 ,/* APS = 1 (small), +* VGL_DET_EN = 1, VGH_DET_EN = 1, +* VGL_TURBO = 1, VGH_TURBO = 1 +*/ +0xFF ,/* VGH1_L_DIV, VGL1_L_DIV (1.5MHz) */ +0xFF ,/* VGH1_R_DIV, VGL1_R_DIV (1.5MHz) */ +0xCC ,/* VGH2_L_DIV, VGL2_L_DIV (2.6MHz) */ +0xCC ,/* VGH2_R_DIV, VGL2_R_DIV (2.6MHz) */ +0x77 ,/* VGH3_L_DIV, VGL3_L_DIV (4.5MHz) */ +0x77 /* VGH3_R_DIV, VGL3_R_DIV (4.5MHz) */ ); + +/* Reference voltage. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETBGP , +0x07 ,/* VREF_SEL = 4.2V */ +0x07 /* NVREF_SEL = 4.2V */ ); +msleep (20 ); + +dsi_dcs_write_seq (dsi,ST7703_CMD_SETVCOM , +0x2C ,/* VCOMDC_F = -0.67V */ +0x2C /* VCOMDC_B = -0.67V */ ); + +/* Undocumented command. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_UNKNOWN_BF ,0x02 ,0x11 ,0x00 ); + +/* This command is to set forward GIP timing. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETGIP1 , +0x82 ,0x10 ,0x06 ,0x05 ,0xA2 ,0x0A ,0xA5 ,0x12 , +0x31 ,0x23 ,0x37 ,0x83 ,0x04 ,0xBC ,0x27 ,0x38 , +0x0C ,0x00 ,0x03 ,0x00 ,0x00 ,0x00 ,0x0C ,0x00 , +0x03 ,0x00 ,0x00 ,0x00 ,0x75 ,0x75 ,0x31 ,0x88 , +0x88 ,0x88 ,0x88 ,0x88 ,0x88 ,0x13 ,0x88 ,0x64 , +0x64 ,0x20 ,0x88 ,0x88 ,0x88 ,0x88 ,0x88 ,0x88 , +0x02 ,0x88 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 , +0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ); + +/* This command is to set backward GIP timing. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETGIP2 , +0x02 ,0x21 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 , +0x00 ,0x00 ,0x00 ,0x00 ,0x02 ,0x46 ,0x02 ,0x88 , +0x88 ,0x88 ,0x88 ,0x88 ,0x88 ,0x64 ,0x88 ,0x13 , +0x57 ,0x13 ,0x88 ,0x88 ,0x88 ,0x88 ,0x88 ,0x88 , +0x75 ,0x88 ,0x23 ,0x14 ,0x00 ,0x00 ,0x02 ,0x00 , +0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 , +0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x03 ,0x0A , +0xA5 ,0x00 ,0x00 ,0x00 ,0x00 ); + +/* Adjust the gamma characteristics of the panel. */ +dsi_dcs_write_seq (dsi,ST7703_CMD_SETGAMMA , +0x00 ,0x09 ,0x0D ,0x23 ,0x27 ,0x3C ,0x41 ,0x35 , +0x07 ,0x0D ,0x0E ,0x12 ,0x13 ,0x10 ,0x12 ,0x12 , +0x18 ,0x00 ,0x09 ,0x0D ,0x23 ,0x27 ,0x3C ,0x41 , +0x35 ,0x07 ,0x0D ,0x0E ,0x12 ,0x13 ,0x10 ,0x12 , +0x12 ,0x18 ); + +return 0 ; +} + +static const struct drm_display_mode xbd599_mode = { + .hdisplay =720 , + .hsync_start =720 +40 , + .hsync_end =720 +40 +40 , + .htotal =720 +40 +40 +40 , + .vdisplay =1440 , + .vsync_start =1440 +18 , + .vsync_end =1440 +18 +10 , + .vtotal =1440 +18 +10 +17 , + .clock =69000 , + .flags =DRM_MODE_FLAG_NHSYNC |DRM_MODE_FLAG_NVSYNC , + .width_mm =68 , + .height_mm =136 , +}; + +static const struct st7703_panel_desc xbd599_desc = { + .mode = &xbd599_mode, + .lanes =4 , + .mode_flags =MIPI_DSI_MODE_VIDEO |MIPI_DSI_MODE_VIDEO_SYNC_PULSE , + .format =MIPI_DSI_FMT_RGB888 , + .init_sequence = xbd599_init_sequence, +}; +static int st7703_enable (struct drm_panel *panel) {struct st7703 *ctx =panel_to_st7703 (panel);
@@ -427,6 +621,7 @@ static int st7703_remove(struct mipi_dsi_device *dsi)static const struct of_device_id st7703_of_match[] = { { .compatible ="rocktech,jh057n00900" , .data = &jh057n00900_panel_desc }, + { .compatible ="xingbangda,xbd599" , .data = &xbd599_desc }, {/* sentinel */ } };MODULE_DEVICE_TABLE (of, st7703_of_match);
Signature · 1 line
2.27.0
PATCH v7 10/13 drm/panel: st7703: Enter sleep after display off
In reply to Ondrej JirmanThe datasheet suggests to issue sleep in after display off as a part of the panel's shutdown sequence.
--- drivers/gpu/drm/panel/panel-sitronix-st7703.c | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-)
drivers/gpu/drm/panel/panel-sitronix-st7703.c +12 -1
@@ -393,8 +393,19 @@ static int st7703_disable(struct drm_panel *panel) {struct st7703 *ctx =panel_to_st7703 (panel);struct mipi_dsi_device *dsi =to_mipi_dsi_device (ctx->dev); +int ret; + + ret =mipi_dsi_dcs_set_display_off (dsi); +if (ret <0 ) +DRM_DEV_ERROR (ctx->dev, +"Failed to turn off the display: %d\n" , ret); -return mipi_dsi_dcs_set_display_off (dsi); + ret =mipi_dsi_dcs_enter_sleep_mode (dsi); +if (ret <0 ) +DRM_DEV_ERROR (ctx->dev, +"Failed to enter sleep mode: %d\n" , ret); + +return 0 ; }static int st7703_unprepare (struct drm_panel *panel)
Signature · 1 line
2.27.0
PATCH v7 11/13 drm/panel: st7703: Assert reset prior to powering down the regulators
In reply to Ondrej JirmanThe reset pin is inverted, so if we don't assert reset, the actual gpio will be high and may keep driving the IO port of the panel.
--- drivers/gpu/drm/panel/panel-sitronix-st7703.c | 1 + 1 file changed, 1 insertion(+)
drivers/gpu/drm/panel/panel-sitronix-st7703.c +1 -0
@@ -415,6 +415,7 @@ static int st7703_unprepare(struct drm_panel *panel)if (!ctx->prepared)return 0 ; +gpiod_set_value_cansleep (ctx->reset_gpio,1 );regulator_disable (ctx->iovcc);regulator_disable (ctx->vcc); ctx->prepared = false;
Signature · 1 line
2.27.0
PATCH v7 12/13 arm64: dts: sun50i-a64-pinephone: Enable LCD support on PinePhone
In reply to Ondrej JirmanFrom: Icenowy Zheng <[email protected]>
PinePhone uses PWM backlight and a XBD599 LCD panel over DSI for display.
Backlight levels curve was optimized by Martijn Braam using a lux meter.
Add its device nodes.
--- .../allwinner/sun50i-a64-pinephone-1.1.dts | 19 ++++++++++ .../dts/allwinner/sun50i-a64-pinephone.dtsi | 35 +++++++++++++++++++ 2 files changed, 54 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts +19 -0
@@ -9,3 +9,22 @@ / { model = "Pine64 PinePhone Braveheart (1.1)"; compatible = "pine64,pinephone-1.1", "allwinner,sun50i-a64"; }; + +&backlight { + power-supply = <®_ldo_io0>; + /* + * PWM backlight circuit on this PinePhone revision was changed since + * 1.0, and the lowest PWM duty cycle that doesn't lead to backlight + * being off is around 20%. Duty cycle for the lowest brightness level + * also varries quite a bit between individual boards, so the lowest + * value here was chosen as a safe default. + */ + brightness-levels = < + 774 793 814 842 + 882 935 1003 1088 + 1192 1316 1462 1633 + 1830 2054 2309 2596 + 2916 3271 3664 4096>; + num-interpolated-steps = <50>; + default-brightness-level = <400>; +};
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi +35 -0
@@ -16,6 +16,13 @@ aliases { serial0 = &uart0; }; + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&r_pwm 0 50000 PWM_POLARITY_INVERTED>; + enable-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */ + /* Backlight configuration differs per PinePhone revision. */ + }; + chosen { stdout-path = "serial0:115200n8"; };
@@ -84,6 +91,30 @@ &dai { status = "okay"; }; +&de { + status = "okay"; +}; + +&dphy { + status = "okay"; +}; + +&dsi { + vcc-dsi-supply = <®_dldo1>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + panel@0 { + compatible = "xingbangda,xbd599"; + reg = <0>; + reset-gpios = <&pio 3 23 GPIO_ACTIVE_LOW>; /* PD23 */ + iovcc-supply = <®_dldo2>; + vcc-supply = <®_ldo_io0>; + backlight = <&backlight>; + }; +}; + &ehci0 { status = "okay"; };
@@ -188,6 +219,10 @@ &r_pio { */ }; +&r_pwm { + status = "okay"; +}; + &r_rsb { status = "okay";
Signature · 1 line
2.27.0
Re: [PATCH v7 12/13] arm64: dts: sun50i-a64-pinephone: Enable LCD support on PinePhone
Quoted 71 lines · Ondrej Jirman
From: Icenowy Zheng <[email protected]>
PinePhone uses PWM backlight and a XBD599 LCD panel over DSI for display.
Backlight levels curve was optimized by Martijn Braam using a lux meter.
Add its device nodes.
Signed-off-by Icenowy Zheng <[email protected]>Signed-off-by Martijn Braam <[email protected]>Signed-off-by Ondrej Jirman <[email protected]>Acked-by Linus Walleij <[email protected]>--- .../allwinner/sun50i-a64-pinephone-1.1.dts | 19 ++++++++++ .../dts/allwinner/sun50i-a64-pinephone.dtsi | 35 +++++++++++++++++++ 2 files changed, 54 insertions(+)arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts +19
-0@@ -9,3 +9,22 @@ / { model = "Pine64 PinePhone Braveheart (1.1)"; compatible = "pine64,pinephone-1.1", "allwinner,sun50i-a64"; }; + +&backlight { + power-supply = <®_ldo_io0>; + /* + * PWM backlight circuit on this PinePhone revision was changed since + * 1.0, and the lowest PWM duty cycle that doesn't lead to backlight + * being off is around 20%. Duty cycle for the lowest brightness level + * also varries quite a bit between individual boards, so the lowest + * value here was chosen as a safe default. + */ + brightness-levels = < + 774 793 814 842 + 882 935 1003 1088 + 1192 1316 1462 1633 + 1830 2054 2309 2596 + 2916 3271 3664 4096>; + num-interpolated-steps = <50>; + default-brightness-level = <400>; +};arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi +10
-0@@ -16,6 +16,13 @@ aliases { serial0 = &uart0; }; + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&r_pwm 0 50000 PWM_POLARITY_INVERTED>; + enable-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */ + /* Backlight configuration differs per PinePhone revision. */ + }; + chosen { stdout-path = "serial0:115200n8"; };@@ -84,6 +91,30 @@ &dai { status = "okay"; }; +&de { + status = "okay"; +};
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi &dai { · line 106
Quoted 10 lines
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi +10
-0+ +&dphy { + status = "okay"; +}; + +&dsi { + vcc-dsi-supply = <®_dldo1>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay";
If you're about to send a new version, you can remove #address-cells and #size-cells too, they're already set in the DTSI.
Maxime
PATCH v7 13/13 arm64: dts: sun50i-a64-pinephone: Add touchscreen support
In reply to Ondrej JirmanPinephone has a Goodix GT917S capacitive touchscreen controller on I2C0 bus. Add support for it.
--- .../dts/allwinner/sun50i-a64-pinephone.dtsi | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi +19 -0
@@ -123,6 +123,25 @@ &ehci1 { status = "okay"; }; +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + status = "okay"; + + touchscreen@5d { + compatible = "goodix,gt917s", "goodix,gt911"; + reg = <0x5d>; + interrupt-parent = <&pio>; + interrupts = <7 4 IRQ_TYPE_LEVEL_HIGH>; /* PH4 */ + irq-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + reset-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */ + AVDD28-supply = <®_ldo_io0>; + VDDIO-supply = <®_ldo_io0>; + touchscreen-size-x = <720>; + touchscreen-size-y = <1440>; + }; +}; + &i2c1 { status = "okay";
Signature · 1 line
2.27.0
Hi Ondrej.
Quoted 3 lines · Ondrej Jirman
This patchset adds support for the LCD panel of PinePhone.
I've tested this on PinePhone 1.0 and 1.2.
Thanks for this nive sereis.
Applied the first 11 patches to drm-misc-next.
The DTS files needs to go in via another tree.
Sam
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Hello Sam,
Quoted 10 lines · Sam Ravnborg
Hi Ondrej.
Quoted 3 lines · Ondrej Jirman
This patchset adds support for the LCD panel of PinePhone.
I've tested this on PinePhone 1.0 and 1.2.
Thanks for this nive sereis.
Applied the first 11 patches to drm-misc-next.
The DTS files needs to go in via another tree.
Thank you very much, too. :)
regards,
o.
Quoted 1 line
Sam